To optimize register read/write operations, the HTC firmwares were patched
to change EP3 and EP4 pipe types from Interrupt to Bulk. So register writes
are submitted as bulk urbs, but register reads are not. Also changing the
register read endpoint pipe as bulk type when URBs are filled improves the
register reads considerably which results in reduced scan time and CPU
utilization.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes following warning
drivers/net/wireless/ath/ath9k/eeprom_def.c: In function 'ath9k_hw_def_get_num_ant_config'
drivers/net/wireless/ath/ath9k/eeprom_def.c:1425:47: warning: comparison
between 'enum ath9k_hal_freq_band' and 'enum ieee80211_band'
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CHECK drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/ath/ath9k/recv.c:1341:6: warning: symbol 'ath_ant_div_conf_fast_divbias' was not declared. Should it be static?
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Print raw and decoded rxfilter in debufs 'wiphy' file.
Also, move variable-length printouts to bottom of file to
make bounds checking easier.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When there is more than one VIF, listen for all beacons
and ensure ATH9K_RX_FILTER_MCAST_BCAST_ALL is set.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use key management functions which have been moved to ath/key.c and remove
ath9k copies of these functions and other now unused definitions.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace common->splitmic with ATH_CRYPT_CAP_MIC_COMBINED flag.
splitmic has to be used when the ATH_CRYPT_CAP_MIC_COMBINED capability flag is
not set.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If AR_KeyMiss is set in the rx descriptor and AR_RxFrameOK is unset,
the hardware could not locate a valid key during a decryption attempt.
In this case, the frame must not be reported as decrypted, otherwise
mac80211 sees only random garbage.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At the time the .add_interface driver op is called, the interface has not
been marked as running yet, so ieee80211_iterate_active_interfaces will
not pass it to the iterator function.
Because of this, the calculated BSSID mask is wrong, which breaks multi-BSS
operation.
Additionally, the current way of comparing all addresses against each other
is pointless, as the hardware only uses the hardware MAC address and the BSSID
mask for matching the destination address, so all the address array
reallocation is completely unnecessary.
This patch simplifies the logic by setting the initial mask bytes to 0xff
and removing all bits in the iterator call that don't match the hardware MAC
address. It also calls the iterator for the vif that was passed to
add_interface()
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The CPU consumption during the scan period is high, since
the register write go over Interrupt endpoint. On downloading
the firmware to the target, the USB descriptors are
'patched' to change the type of the endpoints from Interrupt
to Bulk.
With this fix, the CPU usage during a scan run comes down to
acceptable levels.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_wmi_ctrl_rx is racy with ath9k_wmi_tasklet on event notification
due to which the wmi_skb may be overwritten which leads to memory leak.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace (sizeof(ofdm_level_table)/sizeof(ofdm_level_table[0]) with
ARRAY_SIZE(ofdm_level_table), and (sizeof(cck_level_table)/
sizeof(cck_level_table[0]) with ARRAY_SIZE(cck_level_table) in
drivers/net/wireless/ath/ath9k/ani.c
Signed-off-by: Nikitas Angelinas <nikitasangelinas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To reduce scan time, enable fastcc for AR7010
(fastcc == fast channel change -- JWL)
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For AR9271 chips, if partial reset is done while scanning, the cycpwrThr1
will be set to maximum. This causes the degrade in DL throughput.
So restore the ANI registers to default during the partial reset.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By enabling fastcc, the scan time reduced to half.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This algorithm chooses the best main and alt lna out of
LNA1, LNA2, LNA1+LNA2 and LNA1-LNA2 to improve rx for single
chain chips(AR9285). This would greatly improve rx when there
is only one antenna is connected with AR9285.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is enabled only for ar9285.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 5 GHz CTL indexes were not being read for all hardware
devices due to the masking out through the CTL_MODE_M mask
being one bit too short. Without this the calibrated regulatory
maximum values were not being picked up when devices operate
on 5 GHz in HT40 mode. The final output power used for Atheros
devices is the minimum between the calibrated CTL values and
what CRDA provides.
Cc: stable@kernel.org [2.6.27+]
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The EEPROM is compressed on AR9003, upon decompression
the wrong upper limit was being used for the block which
prevented the 5 GHz CTL indexes from being used, which are
stored towards the end of the EEPROM block. This fix allows
the actual intended regulatory limits to be used on AR9003
hardware.
Cc: stable@kernel.org [2.6.36+]
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to the hardware documentation, the MIC failure bit is only
valid if the frame was decrypted using a valid TKIP key and is not a
fragment.
In some setups I've seen hardware-reported MIC failures on an AP that
was configured for CCMP only, so it's clear that additional checks are
necessary.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While scanning, ANI is triggered unnecessarily where sta is in
unassociated state. And cancelling ani work in ath9k_htc_stop
is not required.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All major Atheros customers require the led to be in continuous
ON state rather than the blinking pattern.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, mac80211 translates the cfg80211
cipher suite selectors into ALG_* values.
That isn't all too useful, and some drivers
benefit from the distinction between WEP40
and WEP104 as well. Therefore, convert it
all to use the cipher suite selectors.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use ath9k_cmn_get_hw_crypto_keytype() instead which is
already exported and shared, and does exactly the same thing.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Outdent the code following the if.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@
(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
if (p1[0].column == p2[0].column):
cocci.print_main("branch",p1)
cocci.print_secs("after",p2)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the noise floor limits are being bypassed because of strong
interference, sensitivity is also reduced.
In order to recover from this as quickly as possible, trigger a
long periodic calibration every second instead of every 30 seconds,
until the NF median is within limits again. This is especially important
if the interference lasts for a while, since it takes multiple clean
NF calibrations to bring the median back to normal.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When beacons get stuck in AP mode, the most likely cause is interference.
Such interference can often go on for a while, and too many consecutive
beacon misses can lead to connected clients getting dropped.
Since connected clients might not be subjected to the same interference
if that happens to be very local, the AP should try to deal with it as
good as it can. One way to do this is to trigger an NF calibration with
automatic baseband update right after the beacon miss. In my tests with
very strong interference, this allowed the AP to continue transmitting
beacons after only 2-3 misses, which allows a normal client to stay
connected.
With some of the newer - really sensitive - chips, the maximum noise
floor limit is very low, which can be problematic during very strong
interference. To avoid an endless loop of stuck beacons -> nfcal ->
periodic calibration -> stuck beacons, the beacon miss event also sets
a flag, which allows the calibration code to bypass the chip specific
maximum NF value. This flag is automatically cleared, as soon as the
first NF median goes back below the limits for all chains.
In my tests, this allowed an ath9k AP to survive very strong interference
(measured NF: -68, or sometimes even higher) without losing connectivity
to its clients. Even under these conditions, I was able to transmit
several mbits/s through the interface.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stuck beacons are a useful indicator for debugging various PHY
issues such as calibration. Putting them on the same debug level
as the other beacon stuff makes it hard to spot them in huge amounts
of spam.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This helps us debug channel changes better.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch handles the firmware loading properly
for device ID 7015.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some APs advertise that they may be HT40 capable in the capabilites
but the current operating channel configuration may be only HT20.
This causes disconnection as ath9k_htc sets WLAN_RC_40_FLAG despite
the AP operating in HT20 mode.
Hence set this flag only if the current channel configuration
is HT40 enabled.
Cc: stable@kernel.org
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_rx_skb_preprocess nulls rxs and the mactime is never set again -
mactime is always 0. This causes problems in IBSS mode.
ieee80211_rx_bss_info uses mactime to decide if an IBSS merge is needed.
Without this patch the merge is triggered by each beacon received.
This can be recognized by the "beacon TSF higher than local TSF - IBSS
merge with BSSID" log message accompanying each beacon.
This problem was not completely fixed in commit
a6d2055b02 and is not a stable kernel fix.
It is solely intended for wireless-testing.
Signed-off-by: Jan Friedrich <jft@dev2day.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I noticed a possible issue in the paused flag management of the
ath_atx_tid data structure. In particular, in a noisy environment and
under heavy load, I observed that the AGGR session establishment could
fail several times consecutively causing values of the paused flag
greater than one for this TID (ath_tx_pause_tid is called more than
once from ath_tx_aggr_start).
Considering that the session for this TID can not be established also
after the mac80211 stack calls the ieee80211_agg_tx_operational() since
the ath_tx_aggr_resume() lowers the paused flag only by one.
This patch also replaces some BUG_ON calls with WARN_ON, as even if
these unlikely conditions happen, it's not fatal enough to justify a
BUG_ON.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9003 was not relying on the CTL indexes from the EEPROM for capping the
max output power. The CTL indexes from the EEPROM provide calibrated
limits for output power for each tested and supported frequency. Without
this the device operates at a power level which only conforms to the
transmit spectrum mask as specified by IEEE Annex I.2.3.
The regulatory limit by CRDA is always used but does not provide
calibrated values for optimal performance, specially on band edges.
Using the calibrated data from the EEPROM ensures the device
operates at optimal output power while still ensuring proper
regulatory compliance. The device uses the minimum of these tree
values, the value from CRDA, the calibrated value from CTL indexex,
and the value to conform to the IEEE transmit spectrum mask.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR5008-AR9002, other forms of calibration must not be started while
the noise floor calibration is running, as this can create invalid
readings which were sometimes not even recoverable by any further
calibration attempts.
This patch also ensures that the result of noise floor measurements
are processed faster and also allows the result of the initial
calibration on reset to make it into the NF history buffer
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The noise floor history buffer is currently not kept per channel, which
can lead to problems when changing channels from a clean channel to a
noisy one. Also when switching from HT20 to HT40, the noise floor
history buffer is full of measurements, but none of them contain data
for the extension channel, which it needs quite a bit of time to recover
from.
This patch puts all the per-channel calibration data into a single data
structure, and gives the the driver control over whether that is used
per-channel or even not used for some channels.
For ath9k_htc, I decided to keep this per-channel in order to avoid
creating regressions.
For ath9k, the data is kept only for the operating channel, which saves
some space. ath9k_hw takes care of wiping old data when the operating
channel or its channel flags change.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously the software scan callback was used to indicate to the hardware,
when it was safe to calibrate. This didn't really work properly, because it
depends on a specific order of software scan callbacks vs. channel changes.
Also, software scans are not the only thing that triggers off-channel
activity, so it's better to use the newly added indication from mac80211 for
this and not use the software scan callback for anything calibration related.
This fixes at least some of the invalid noise floor readings that I've seen
in AP mode on AR9160
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Writes to the analog shift registers, which are issues by the initval
programming function, require a 100 usec delay (similar to AR9002,
but in a different register range).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When updating the PAPRD table in hardware, PAPRD itself needs to be
disabled first, otherwise the hardware can throw a data bus error,
which upsets at least some platforms.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The periodic noise floor calibration is broken on this chip family, because
it keeps triggering a software-filtered noise floor calibration, but never
reads the result before uploading the history buffer value to the hardware.
Fix this with a call to ath9k_hw_getnf(), just like on AR9002.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR9003 the initial noise floor calibration is currently triggered
at the end of the reset without allowing the hardware to update the
baseband settings. This could potentially make scans in noisy
environments a bit more unreliable, so use the same calibration
sequence that is used on AR9002.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When issuing two consecutive scans you could often end up
getting in the logs:
"ath9k: Two wiphys trying to scan at the same time"
This message is due to a race in mac80211 but addressing
that race requires some more major changes on the driver
and perhaps optimizations on mac80211 like removing the
scan complete callback alltogether. Its too late to address
this this kernel release so supress the complaint and annotate
this needs fixing for later.
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
base index is not used anymore and so remove it.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The user ratekbs of MCS15 ShortGI is incorrect and can not be lesser
than MCS15 rate. This incorrect rate may affect switching to higher
rates as the rate control algorithm always finds MCS15 is better
than MCS15 ShortGI and results in lower throughput. Fix this by
feeding the correct user ratekbs for MCS15 ShortGI rate.
This issue affects 3 stream case very badly as the 3 stream rates are
not used at all once we scale down to MCS15 from 3 stream rates.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds 3 stream rate control support for AR938X family
chipsets which supports 3 streams.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
replace valid and valid_single_stream in rate table with bit masks
and reorganize the code so adding 3x3 rate control would be easier.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The noisefloor array index always corresponds to the rx chain number it
belongs to (with an offset of 3 for the extension chain).
It's much simpler (and actually more correct) to directly use the
chainmask to calculate the bitmask for the noisefloor array, instead of
using these weird chip revision checks and hardcoded mask values.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the noisefloor array, the extension channel values start at index 3
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the hardware is configured in HT20 mode, noise floor readings for
the extension channel often return invalid values, which keep the
values in the NF history buffer at the hardware-specific maximum limit.
Fix this by discarding the extension channel values when in HT20 mode.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an aggregation session is being cleaned up, while the tx status
for some frames is being processed, the TID is flushed and its buffers
are sent out.
Unfortunately that left the pending un-acked frames unprocessed, thus
leaking buffers. Fix this by reordering the code so that those frames
are processed first, before the TID is flushed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes txq state(txq->stopped) can be marked as started but the actual
queue may not be started (in ATH_WIPHY_SCAN state, for example). Fix this.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The snprintf() function returns the number of characters that would have
been written (not counting the NUL character on the end). It could
potentially be larger than the size of the buffer.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath/ath9k/main.c:282:26: warning: incorrect type in assignment (different base types)
drivers/net/wireless/ath/ath9k/main.c:282:26: expected restricted __le16 [usertype] duration_id
drivers/net/wireless/ath/ath9k/main.c:282:26: got int
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An A-MPDU may contain several subframes each containing its own
CRC for the data. Each subframe also has a respective CRC for the
MPDU length and 4 reserved bits (aka delimeter CRC). AR9003 will
ACK frames that have a valid data CRC but have failed to pass the
CRC for the MPDU length, if and only if the subframe is not the
last subframe in an A-MPDU and if an OFDM phy OFDM reset error has
been caught. Discarding those subframes results in packet loss under
heavy stress conditions, an example being UDP video. Since the
frames are ACK'd by hardware we need to let these frames through
and process them as valid frames.
Cc: Tushit Jain <tushit.jain@atheros.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes this sparse complaint:
CHECK drivers/net/wireless/ath/ath9k/htc_drv_main.c
drivers/net/wireless/ath/ath9k/htc_drv_main.c:441:5:
warning: symbol 'ath9k_htc_tx_aggr_oper'
was not declared. Should it be static?
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to documentation, The following chip revisions were never sold:
- AR9280 v1.0
- AR9285 v1.0
- AR9285 v1.1
- AR9287 v1.0
Removing initvals specific to these chip revisions saves around 30k in
binary size (tested on MIPS).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch 'ath9k: fix a buffer leak in A-MPDU completion' addressed the
issue of running out of buffers/descriptors in the tx path if a STA is
deleted while tx status feedback is still pending.
The remaining issue is that the skbs of the buffers are not reclaimed,
leaving a memory leak.
This patch fixes this issue by running the buffers through
ath_tx_complete_buf(), ensuring that the pending frames counter is also
updated.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
num_sec_wiphy means max secondary wifis that the driver can accomudate.
So cancelling wiphy work should be based on the presence of
secondary wifis.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove tMinCalPower from ath9k_hw_set_def_power_cal_table(), as it's
never used. Remove corresponding arguments of the functions calculating
that value.
Original patch by Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
LED should be ON when the radio is put into FULL SLEEP mode during the idle
unassociated state.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR5008+ and AR9003 currently use two separate implementations of the
ath9k_hw_loadnf function. There are three main differences:
- PHY registers for AR9003 are different
- AR9003 always uses 3 chains, earlier versions are more selective
- The AR9003 variant contains a fix for NF load timeouts
This patch merges the two implementations into one, storing the
register array in the ath_hw struct. The fix for NF load timeouts is
not just relevant for AR9003, but also important for earlier hardware,
so it's better to just keep one common implementation.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Occasionally the hardware can send out tx status information with the wrong
TID. In that case, the BA status cannot be trusted and the aggregate
must be retransmitted.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the receive path gets stuck, a full hardware reset is necessary to
recover from it. If this happens during a scan, the whole scan might fail,
as each channel change bypasses the full reset sequence.
Fix this by resetting the fast channel change flag if stopping the
receive path fails.
This will reduce the number of error messages that look like this:
ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x40000020
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PDADC values were only generated for values surrounding the target
index, however not for the target index itself, leading to a minor
error in the generated curve.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR9285, the antenna switch configuration register uses more than just
16 bits. Because of an arbitrary mask applied to the EEPROM value that
stores this configuration, diversity was broken in some cases, leading
to a significant degradation in signal strength.
Fix this by changing the callback to return a 32 bit value and remove
the arbitrary mask.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When ath_tx_complete_aggr() is called, it's responsible for returning
all buffers in the linked list. This was not done when the STA lookup
failed, leading to a race condition that could leak a few buffers when
a STA just disconnected.
Fix this by immediately returning all buffers to the free list in this case.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It looks like it might be possible for a TID to be paused, while still
holding some queued buffers, however ath_tx_node_cleanup currently only
iterates over active TIDs.
Fix this by always checking every allocated TID for the STA that is being
cleaned up.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Failure cases within ath9k_hif_usb_alloc_urbs are failed
to release allocated memory.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit eed8e22f01 added support for using
multicast key lookup to support per-vif/sta keys for AP and ad-hoc.
Unfortunately, it also introduced a crash in ad-hoc mode when the sta
pointer is NULL, which happens when setting up an interface with WEP
keys. This patch fixes it by falling back to the assigned key index.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_check_alive() occasionally returns false, as the hardware
is still processing data in a specific state. Fix this issue by
repeating the test a few times with longer delay inbetween attempts.
This gets rid of excessive hardware resets that appear frequently on
some AR9132 based devices, but could also happen on AR9280.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Björn Smedman <bjorn.smedman@venatech.se>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This refactors the noise floor range checks to make them generic,
and adds proper ranges for each supported chip type.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This includes the following changes/fixes:
- a bugfix for stuck beacon issues
- timing changes for improved performance
- AGC setting improvements
- fixes for high temperature issues on some chips
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This format is generated by the initval tool, available at:
git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/initvals-tool.git
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When issuing a reset, the TSF value is lost in the hardware because of
the 913x specific cold reset. As with some AR9280 cards, the TSF needs
to be preserved in software here.
Additionally, there's an issue that frequently prevents a successful
TSF write directly after the chip reset. In this case, repeating the
TSF write after the initval-writes usually works.
This patch detects failed TSF writes and recovers from them, taking
into account the delay caused by the initval writes.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Björn Smedman <bjorn.smedman@venatech.se>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'bf_retries' field of the ath_buf structure was used for both
software retries (AMPDU subframes) and hardware retries (legacy
frames). This led to a wrong retry count being reported for the A-MPDU
rate control stats.
This patch changes the code to no longer use bf_retries for reporting
retry counts, but instead always using the real on-chip retry count
from the ath_tx_status.
Additionally, if the first subframe of an A-MPDU was not acked, the tx
status report is submitted along with the first acked subframe, which
may not contain the correct rates in the tx info.
This is easily corrected by saving the tx rate info before looping over
subframes, and then copying it back once the A-MPDU status report is
submitted.
In my tests this change improves throughput visibly.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Björn Smedman <bjorn.smedman@venatech.se>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move ath9k_ps_wakeup() down just before accessing hw registers.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is possbile that the transmission of paprd test frame
might not get completed in 100ms if tx is stuck. Freeing
this skb upon timeout in ath_paprd_calibrate() will result
in accessing already freed memory when the associated pending
buffer is drained in txq. This patch fixes this issue.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are few places where ANI is started without checking
if it is right to start. This might lead to a case where ani
timer would be left undeleted and cause improper memory acccess
during module unload. This bug is clearly exposed with
paprd support where the driver detects tx hang and does a
chip reset. During this reset ani is (re)started without checking
if it needs to be started. This would leave a timer scheduled
even after all the resources are freed and cause a panic.
This patch introduces a bit in sc_flags to indicate if ani
needs to be started in sw_scan_start() and ath_reset().
This would fix the following panic. This issue is easily seen
with ar9003 + paprd.
BUG: unable to handle kernel paging request at 0000000000003f38
[<ffffffff81075391>] ? __queue_work+0x41/0x50
[<ffffffff8106afaa>] run_timer_softirq+0x17a/0x370
[<ffffffff81088be8>] ? tick_dev_program_event+0x48/0x110
[<ffffffff81061f69>] __do_softirq+0xb9/0x1f0
[<ffffffff810ba060>] ? handle_IRQ_event+0x50/0x160
[<ffffffff8100af5c>] call_softirq+0x1c/0x30
[<ffffffff8100c9f5>] do_softirq+0x65/0xa0
[<ffffffff81061e25>] irq_exit+0x85/0x90
[<ffffffff8155e095>] do_IRQ+0x75/0xf0
[<ffffffff815570d3>] ret_from_intr+0x0/0x11
<EOI>
[<ffffffff812fd67b>] ? acpi_idle_enter_simple+0xe4/0x119
[<ffffffff812fd674>] ? acpi_idle_enter_simple+0xdd/0x119
[<ffffffff81441c87>] cpuidle_idle_call+0xa7/0x140
[<ffffffff81008da3>] cpu_idle+0xb3/0x110
[<ffffffff81550722>] start_secondary+0x1ee/0x1f5
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some vendors require the LED to be ON always irrespective of any
radio activity. Introducing a module parameter to disable blinking,
so that one can choose between always on or led blink during
activity.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Without this we could start trying to work with the device without
it being fully functional yet and loose some packets upon resume.
Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: Madhan Jaganathan <madhan.jaganathan@atheros.com>
signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The array we use will vary depending on whether or not we are
to go to lower power or not. The default values (iniPcieSerdes)
are a copy or what go into the registers through the INI files.
Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: Madhan Jaganathan <madhan.jaganathan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This can be useful during testing of new ASPM tweaks which often
have to be done through the PCI Serializer-Deserializer (SERDES).
Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: Madhan Jaganathan <madhan.jaganathan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The LowPower array writes disables the PLL when ASPM is enabled.
The host driver makes quite a few calls to ath9k_hw_configpcipowersave()
and these same calls also need to ensure the PLL is off when they issue
it.
Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: Madhan Jaganathan <madhan.jaganathan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AR_WA register should not be read when in sleep state so
add a variable we can stash its value into for when we need
to set it. Additionally the AR_WA_D3_TO_L1_DISABLE_REAL
(bit 16) needs to be removed.
Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: Madhan Jaganathan <madhan.jaganathan@atheros.com>
signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds USB IDs for some more supported
devices.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that ampdu_action() can sleep, remove all
the driver hacks and just issue WMI commands
to the target.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IBSS requires the cwmin and cwmax to be respected when
we reset the txqueues on AR9003 otherwise the distribution
of beacons will be balanced towards the AR9003 card first
preventing equal contention for air time for other peers
on the IBSS.
Without this IBSS will work but only the AR9003 card will be
be issuing beacons on the IBSS.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This capability check is no longer used, so it can be removed along with
the now-obsolete ath9k_hw_getcapability function.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 already masks the HT sta capabilities based on hardware support
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver always sets this to enabled, but this can be simplified with
a small change to ah->sta_id1_defaults instead.
This change also removes the now-obsolete ath9k_hw_setcapability function.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is only used as a workaround for an issue in one specific hw revision.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
replace calls that read this capability with accesses to ath9k_hw's
regulatory data.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All of the ciphers that are tested for are always supported
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All AR9003 features are now complete so enable AR9003
support.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_setmac() only copies the mac address it is called with into
common->macaddr, yet in all call sites, the supplied mac address pointer
is already common->macaddr.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Debugfs requires a u32 for bool knobs though so we turn the
ath9k_hw knob into a u32 as well.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k tries to prevent WMM queue tx buffer starvation caused by
traffic on different queues by limiting the number of pending frames
in a tx queue (tracked in the ath_buf structure). This had a leak
issue, because the a skb can be reassigned to a different ath_buf
in the tx path, causing the pending frame counter to become inaccurate.
To fix this, track the number of frames in an array in the softc,
using the mac80211 queue mapping as index.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR5416 and all newer chipsets use a 32 bit rx timestamp, so there
is no need to keep the 15 bit timestamp extending logic around.
This patch removes ath9k_hw_extend_tsf (replaced by a call to
ath9k_hw_gettsf64), and reduces the frequency of TSF reads, which
can improve performance in some cases.
This change also has the side effect of making rx timestamps
more accurate.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_get_mac80211_qnum() expects the queue 'subtype'
(internal ID for the WMM AC) as argument when looking up
the mac80211 queue, however ath_wake_mac80211_queue provides
txq->axq_qnum instead, which contains the hardware queue
number. Fix this by keeping track of the WMM class ID in
the txq data structure.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All AR9003 devices are PCI-E only, the extra delay here
is not required and only reduces the delay for loading
the initial register values by at least 14ms.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9003 has been tested with the new ANI implementation
and so ANI can now be enabled for that family.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for ANI for AR9003. The implementation for
ANI for AR9003 is slightly different than the one used for
the older chipset families. It can technically be used for
the older families as well but this is not yet fully tested
so we only enable the new ANI for the AR5008, AR9001 and AR9002
families with a module parameter, force_new_ani.
The old ANI implementation is left intact.
Details of the new ANI implemention:
* ANI adjustment logic is now table driven so that each ANI level
setting is parameterized. This makes adjustments much more
deterministic than the old procedure based logic and allows
adjustments to be made incrementally to several parameters per
level.
* ANI register settings are now relative to INI values; so ANI
param zero level == INI value. Appropriate floor and ceiling
values are obeyed when adjustments are combined with INI values.
* ANI processing is done once per second rather that every 100ms.
The poll interval is now a set upon hardware initialization and
can be picked up by the core driver.
* OFDM error and CCK error processing are made in a round robin
fashion rather than allowing all OFDM adjustments to be made
before CCK adjustments.
* ANI adjusts MRC CCK off in the presence of high CCK errors
* When adjusting spur immunity (SI) and OFDM weak signal detection,
ANI now sets register values for the extension channel too
* When adjusting FIR step (ST), ANI now sets register for FIR step
low too
* FIR step adjustments now allow for an extra level of immunity for
extremely noisy environments
* The old Noise immunity setting (NI), which changes coarse low, size
desired, etc have been removed. Changing these settings could affect
up RIFS RX as well.
* CCK weak signal adjustment is no longer used
* ANI no longer enables phy error interrupts; in all cases phy hw
counting registers are used instead
* The phy error count (overflow) interrupts are also no longer used
for ANI adjustments. All ANI adjustments are made via the polling
routine and no adjustments are possible in the ISR context anymore
* A history settings buffer is now correctly used for each channel;
channel settings are initialized with the defaults but later
changes are restored when returning back to that channel
* When scanning, ANI is disabled settings are returned to (INI) defaults.
* OFDM phy error thresholds are now 400 & 1000 (errors/second units) for
low/high water marks, providing increased stability/hysteresis when
changing levels.
* Similarly CCK phy error thresholds are now 300 & 600 (errors/second)
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new ANI implementation will use this to skip ANI
calibration upon a scan. This cannot be ported to the
older ANI implementation unless default ANI values from
the ANI are also used upon a scan. This is essentially
what one of the things thenew ANI does.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AR9003 hardware family will use a slightly modified ANI
implementation which has not yet been tested on the other hardware
families. To allow for this new ANI implementation a few ANI
calls need to be abstracted away. This patch just allows for
each hardware family to declare their own ANI ops and annotates
the current ANI implementation as old.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We get an MIB interrupt when we hit certain PHY error counter
thresholds. If ANI is disabled but the MIB interrupt is enabled
we'll keep around the old MIB interrupt causes.
Since ath9k disables the MIB interrupt when ANI is disabled
this is not a fix, but more of a sanity fix in case we ever
need the MIB interrupt enabled but disabling ANI.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The clock rate was assumed to be static but it actually
changes depending on the mode of operation, correct this
to help improve the calcuation of the listenTime for ANI.
This change will help adjust ANI more accurately on different
PHY thresholds.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These will be used by the ANI code next.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow drivers to sleep, and indicate this in
the documentation. ath9k has some locking I
don't understand, so keep it safe and disable
BHs in it, all other drivers look fine with
the context change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The non-irqsafe aggregation start/stop done
callbacks are currently only used by ath9k_htc,
and can cause callbacks into the driver again.
This might lead to locking issues, which will
only get worse as we modify locking. To avoid
trouble, remove the non-irqsafe versions and
change ath9k_htc to use those instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes 'make -j24 CONFIG_DEBUG_SECTION_MISMATCH=y' warning:
drivers/net/wireless/ath/ath9k/eeprom_4k.c: In function ‘ath9k_hw_get_4k_gain_boundaries_pdadcs.clone.1’:
drivers/net/wireless/ath/ath9k/eeprom_4k.c:311: error: ‘minPwrT4’ may be used uninitialized in this function
drivers/net/wireless/ath/ath9k/eeprom_9287.c: In function ‘ath9k_hw_get_AR9287_gain_boundaries_pdadcs’:
drivers/net/wireless/ath/ath9k/eeprom_9287.c:302: error: ‘minPwrT4’ may be used uninitialized in this function
drivers/net/wireless/ath/ath9k/eeprom_def.c: In function ‘ath9k_hw_get_def_gain_boundaries_pdadcs.clone.0’:
drivers/net/wireless/ath/ath9k/eeprom_def.c:679: error: ‘minPwrT4’ may be used uninitialized in this function
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The following commit added an entry in 11na and 11ng rate
table but missed to update its rate count field. This
inconsistency between the rate count and the actual number
of rates in the table will leave out the final rate entry
(mcs15 with half gi in ht40) while forming the valid
rate indices. Not having mcs15+shortGI in ht40 will have
a performance impact (on max throughput) of about 10% both
in nght40 and naht40 mode.
Author: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Date: Thu May 13 18:42:38 2010 -0700
ath9k: Enable Short GI in 20 Mhz for ar9287 and later chips
This patch enables short GI rx at all rates and tx at mcs15
for 20 Mhz channel width also.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For non-AR9271 chips, the credit size is different
and has to be configured appropriately.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR7010 is dual-band. Setup the channels and rateset
for 5GHz band.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rate information on the target has to be updated
for 2-stream devices, along with the correct chainmask.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The supported MCS rate set has to be setup properly
for 2-stream devices.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the USB device IDs for AR7010 and handle
firmware loading properly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes programming the byte swap registers
for chipsets other than AR9271. This is needed for
AR7010.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not assign the FW name to driver_info but determine
it dynamically on device probe. This facilitates adding new
firmware.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
