Change USB controller version to 2.5 in compatible string for T2080/T2081
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
T1042RDB_PI is Freescale Reference Design Board supporting the T1042
QorIQ Power Architecture™ processor. T1042 is a reduced personality
of T1040 SoC without Integrated 8-port Gigabit. The board is designed
with low power features targeted for Printing Image Market.
T1042RDB_PI is similar to T1040RDB board with few differences like
it has video interface, supports T1042 personality only
T1042RDB_PI board Overview
-----------------------
- SERDES Connections, 8 lanes supporting:
- PCI
- SATA 2.0
- DDR Controller
- Supports rates of up to 1600 MHz data-rate
- Supports one DDR3LP UDIMM
-IFC/Local Bus
- NAND flash: 1GB 8-bit NAND flash
- NOR: 128MB 16-bit NOR Flash
- Ethernet
- Two on-board RGMII 10/100/1G ethernet ports.
- PHY #0 remains powered up during deep-sleep
- CPLD
- Clocks
- System and DDR clock (SYSCLK, “DDRCLK”)
- SERDES clocks
- Power Supplies
- USB
- Supports two USB 2.0 ports with integrated PHYs
- Two type A ports with 5V@1.5A per port.
- SDHC
- SDHC/SDXC connector
- SPI
- On-board 64MB SPI flash
- I2C
- Device connected: EEPROM, thermal monitor, VID controller, RTC
- Other IO
- Two Serial ports
- ProfiBus port
Add support for T1042RDB_PI board:
-add device tree
-Add entry in corenet_generic.c, as it is similar to other corenet platforms
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
T1040/T1042RDB is Freescale Reference Design Board.
The board can support both T1040/T1042 QorIQ Power Architecture™ processor.
T1040/T1042RDB board Overview
-----------------------
- SERDES Connections, 8 lanes supporting:
- PCI
- SGMII
- QSGMII
- SATA 2.0
- DDR Controller
- Supports rates of up to 1600 MHz data-rate
- Supports one DDR3LP UDIMM
-IFC/Local Bus
- NAND flash: 1GB 8-bit NAND flash
- NOR: 128MB 16-bit NOR Flash
- Ethernet
- Two on-board RGMII 10/100/1G ethernet ports.
- PHY #0 remains powered up during deep-sleep
- CPLD
- Clocks
- System and DDR clock (SYSCLK, “DDRCLK”)
- SERDES clocks
- Power Supplies
- USB
- Supports two USB 2.0 ports with integrated PHYs
- Two type A ports with 5V@1.5A per port.
- SDHC
- SDHC/SDXC connector
- SPI
- On-board 64MB SPI flash
- I2C
- Devices connected: EEPROM, thermal monitor, VID controller
- Other IO
- Two Serial ports
- ProfiBus port
Add support for T1040/T1042 RDB board:
-add device tree
-add entry in Kconfig to build
-Add entry in corenet_generic.c, as it is similar to other corenet platforms
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Change USB controller version to 2.5 in compatible string for T4240
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Pull more powerpc updates from Ben Herrenschmidt:
"Here are some more powerpc bits for 3.17, essentially fixes.
The biggest series, also aimed at -stable, is from Aneesh and is the
result of weeks and weeks of debugging to find out why the heck or THP
implementation was occasionally triggering multi-hit errors in our
level 1 TLB. It ended up being a combination of issues including
subtleties as to how we should invalidate those special 'MPSS' pages
we use to allow the use of 16M pages inside 4K/64K "base page size"
segments (you really have to love our MMU !)
Another interesting one in the "OMG" category is the series from
Michael adding memory barriers to spin_is_locked(). That's also the
result of many days of debugging to figure out why the semaphore code
would occasionally crash in ways that made no sense. It ended up
being some creative lock stacking that was defeated by the fact that
our locks allow a load inside the locked section to be re-ordered with
the load of the lock value itself (I'm still of two mind about whether
to kill that once and for all by putting a heavier barrier back into
our lock implementation...). The fixes come with a long explanation
in the cset comments, feel free to read it if you feel like having a
headache today"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (25 commits)
powerpc/thp: Add tracepoints to track hugepage invalidate
powerpc/mm: Use read barrier when creating real_pte
powerpc/thp: Use ACCESS_ONCE when loading pmdp
powerpc/thp: Invalidate with vpn in loop
powerpc/thp: Handle combo pages in invalidate
powerpc/thp: Invalidate old 64K based hash page mapping before insert of 4k pte
powerpc/thp: Don't recompute vsid and ssize in loop on invalidate
powerpc/thp: Add write barrier after updating the valid bit
powerpc: reorder per-cpu NUMA information's initialization
powerpc/perf/hv-24x7: Use kmem_cache_free
powerpc/pseries/hvcserver: Fix endian issue in hvcs_get_partner_info
powerpc: Hard disable interrupts in xmon
powerpc: remove duplicate definition of TEXASR_FS
powerpc/pseries: Avoid deadlock on removing ddw
powerpc/pseries: Failure on removing device node
powerpc/boot: Use correct zlib types for comparison
powerpc/powernv: Interface to register/unregister opal dump region
printk: Add function to return log buffer address and size
powerpc: Add POWER8 features to CPU_FTRS_POSSIBLE/ALWAYS
powerpc/ppc476: Disable BTAC
...
Avoids this warning:
arch/powerpc/boot/gunzip_util.c:118:9: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull slave-dma updates from Vinod Koul:
"Some notable changes are:
- new driver for AMBA AXI NBPF by Guennadi
- new driver for sun6i controller by Maxime
- pl330 drivers fixes from Lar's
- sh-dma updates and fixes from Laurent, Geert and Kuninori
- Documentation updates from Geert
- drivers fixes and updates spread over dw, edma, freescale, mpc512x
etc.."
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (72 commits)
dmaengine: sun6i: depends on RESET_CONTROLLER
dma: at_hdmac: fix invalid remaining bytes detection
dmaengine: nbpfaxi: don't build this driver where it cannot be used
dmaengine: nbpf_error_get_channel() can be static
dma: pl08x: Use correct specifier for size_t values
dmaengine: Remove the context argument to the prep_dma_cyclic operation
dmaengine: nbpfaxi: convert to tasklet
dmaengine: nbpfaxi: fix a theoretical race
dmaengine: add a driver for AMBA AXI NBPF DMAC IP cores
dmaengine: add device tree binding documentation for the nbpfaxi driver
dmaengine: edma: Do not register second device when booted with DT
dmaengine: edma: Do not change the error code returned from edma_alloc_slot
dmaengine: rcar-dmac: Add device tree bindings documentation
dmaengine: shdma: Allocate cyclic sg list dynamically
dmaengine: shdma: Make channel filter ignore unrelated devices
dmaengine: sh: Rework Kconfig and Makefile
dmaengine: sun6i: Fix memory leaks
dmaengine: sun6i: Free the interrupt before killing the tasklet
dmaengine: sun6i: Remove switch statement from buswidth convertion routine
dmaengine: of: kconfig: select DMA_ENGINE when DMA_OF is selected
...
Pull powerpc updates from Ben Herrenschmidt:
"This is the powerpc new goodies for 3.17. The short story:
The biggest bit is Michael removing all of pre-POWER4 processor
support from the 64-bit kernel. POWER3 and rs64. This gets rid of a
ton of old cruft that has been bitrotting in a long while. It was
broken for quite a few versions already and nobody noticed. Nobody
uses those machines anymore. While at it, he cleaned up a bunch of
old dusty cabinets, getting rid of a skeletton or two.
Then, we have some base VFIO support for KVM, which allows assigning
of PCI devices to KVM guests, support for large 64-bit BARs on
"powernv" platforms, support for HMI (Hardware Management Interrupts)
on those same platforms, some sparse-vmemmap improvements (for memory
hotplug),
There is the usual batch of Freescale embedded updates (summary in the
merge commit) and fixes here or there, I think that's it for the
highlights"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (102 commits)
powerpc/eeh: Export eeh_iommu_group_to_pe()
powerpc/eeh: Add missing #ifdef CONFIG_IOMMU_API
powerpc: Reduce scariness of interrupt frames in stack traces
powerpc: start loop at section start of start in vmemmap_populated()
powerpc: implement vmemmap_free()
powerpc: implement vmemmap_remove_mapping() for BOOK3S
powerpc: implement vmemmap_list_free()
powerpc: Fail remap_4k_pfn() if PFN doesn't fit inside PTE
powerpc/book3s: Fix endianess issue for HMI handling on napping cpus.
powerpc/book3s: handle HMIs for cpus in nap mode.
powerpc/powernv: Invoke opal call to handle hmi.
powerpc/book3s: Add basic infrastructure to handle HMI in Linux.
powerpc/iommu: Fix comments with it_page_shift
powerpc/powernv: Handle compound PE in config accessors
powerpc/powernv: Handle compound PE for EEH
powerpc/powernv: Handle compound PE
powerpc/powernv: Split ioda_eeh_get_state()
powerpc/powernv: Allow to freeze PE
powerpc/powernv: Enable M64 aperatus for PHB3
powerpc/eeh: Aux PE data for error log
...
Fix wrong __IO_H definition in boot/io.h
Reported-by: Fernando Silveira <fsilveira@gmail.com>
Signed-off-by: Lucas Tanure <tanure@linux.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Register the controller for device tree based lookup of DMA channels
(non-fatal for backwards compatibility with older device trees) and
provide the '#dma-cells' property in the shared mpc5121.dtsi file
Signed-off-by: Alexander Popov <a13xp0p0v88@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The driver is compatible with SEC version 4.0, which was missing from
device tree resulting that the caam driver doesn't gets probed. Since
SEC is backward compatible with older versions, so this patch adds those
missing versions in c29x device tree.
Signed-off-by: Nitesh Narayan Lal <b44382@freescale.com>
Signed-off-by: Vakul Garg <b16394@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for Freescale T2080/T2081 QDS Development System Board.
The T2080QDS Development System is a high-performance computing,
evaluation, and development platform that supports T2080 QorIQ
Power Architecture processor, with following major features:
T2080QDS feature overview:
Processor:
- T2080 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
Memory:
- Single memory controller capable of supporting DDR3 and DDR3-LP
- Dual DIMM slots up 2133MT/s with ECC
Ethernet interfaces:
- Two 1Gbps RGMII on-board ports
- Four 10Gbps XFI on-board cages
- 1Gbps/2.5Gbps SGMII Riser card
- 10Gbps XAUI Riser card
Accelerator:
- DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
SerDes:
- 16 lanes up to 10.3125GHz
- Supports Aurora debug, PEX, SATA, SGMII, sRIO, HiGig, XFI and XAUI
IFC:
- 128MB NOR Flash, 512MB NAND Flash, PromJet debug port and FPGA
eSPI:
- Three SPI flash (16MB N25Q128A + 8MB EN25S64 + 512KB SST25WF040)
USB:
- Two USB2.0 ports with internal PHY (one Type-A + one micro Type-AB)
PCIE:
- Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0, SR-IOV)
SATA:
- Two SATA 2.0 ports on-board
SRIO:
- Two Serial RapidIO 2.0 ports up to 5 GHz
eSDHC:
- Supports SD/MMC/eMMC Card
DMA:
- Three 8-channels DMA controllers
I2C:
- Four I2C controllers.
UART:
- Dual 4-pins UART serial ports
System Logic:
- QIXIS-II FPGA system controll
T2081QDS board shares the same PCB with T1040QDS with some differences.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The T2080 QorIQ multicore processor combines four dual-threaded e6500 Power
Architecture processor cores with high-performance datapath acceleration
logic and network and peripheral bus interfaces required for networking,
telecom/datacom, wireless infrastructure, and mil/aerospace applications.
The T2080 SoC includes the following function and features:
- Four dual-threaded 64-bit Power architecture e6500 cores, up to 1.8GHz
- 2MB L2 cache and 512KB CoreNet platform cache (CPC)
- Hierarchical interconnect fabric
- One 32-/64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
- 16 SerDes lanes up to 10.3125 GHz
- 8 Ethernet interfaces (multiple 1G/2.5G/10G MACs)
- High-speed peripheral interfaces
- Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0)
- Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz
- Additional peripheral interfaces
- Two serial ATA (SATA 2.0) controllers
- Two high-speed USB 2.0 controllers with integrated PHY
- Enhanced secure digital host controller (SD/SDXC/eMMC)
- Enhanced serial peripheral interface (eSPI)
- Four I2C controllers
- Four 2-pin UARTs or two 4-pin UARTs
- Integrated Flash Controller supporting NAND and NOR flash
- Three eight-channel DMA engines
- Support for hardware virtualization and partitioning enforcement
- QorIQ Platform's Trust Architecture 2.0
T2081 is a reduced personality of T2080 with following difference:
Feature T2080 T2081
1G Ethernet numbers: 8 6
10G Ethernet numbers: 4 2
SerDes lanes: 16 8
Serial RapidIO,RMan: 2 no
SATA Controller: 2 no
Aurora: yes no
SoC Package: 896-pins 780-pins
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[scottwood@freescale.com: added fsl,qoriq-pci-v3.0 for U-Boot compat]
Signed-off-by: Scott Wood <scottwood@freescale.com>
T4240RDB board Specification
----------------------------
Memory subsystem:
6GB DDR3
128MB NOR flash
2GB NAND flash
Ethernet:
Eight 1G SGMII ports
Four 10Gbps SFP+ ports
PCIe:
Two PCIe slots
USB:
Two USB2.0 Type A ports
SDHC:
One SD-card port
SATA:
One SATA port
UART:
Dual RJ45 ports
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The mux2 node is missing the clock-output-names field that is required
by the clk-ppc-corenet driver.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
T4240 has a third DMA engine controller, so add the corresponding DMA
node into the dts file.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
[scottwood@freescale.com: reword commit message]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Pull kbuild updates from Michal Marek:
"Kbuild changes for v3.16-rc1:
- cross-compilation fix so that cc-option is testing the right
compiler
- Fix for make defconfig all
- Using relative paths to the object and source directory where
possible, plus fixes for the fallout of the change
- several cleanups in the Makefiles and scripts
The powerpc fix is from today, because it was only discovered
recently. The rest has been in linux-next for some time"
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
powerpc: Avoid circular dependency with zImage.%
kbuild: create include/config directory in scripts/kconfig/Makefile
kbuild: do not create include/linux directory
Makefile: Fix unrecognized cross-compiler command line options
kbuild: do not add "selinux" to subdir- twice
um: Fix for relative objtree when generating x86 headers
kbuild: Use relative path when building in a subdir of the source tree
kbuild: Use relative path when building in the source tree
kbuild: Use relative path for $(objtree)
firmware: Use $(quote) in the Makefile
firmware: Simplify directory creation
kbuild: trivial - fix comment block indent
kbuild: trivial - remove trailing spaces
kbuild: support simultaneous "make %config" and "make all"
kbuild: move extra gcc checks to scripts/Makefile.extrawarn
The rule to create the final images uses a zImage.% pattern.
Unfortunately, this also matches the names of the zImage.*.lds linker
scripts, which appear as a dependency of the final images. This somehow
worked when $(srctree) used to be an absolute path, but now the pattern
matches too much. List only the images from $(image-y) as the target of
the rule, to avoid the circular dependency.
Reported-and-tested-by: Mike Qiu <qiudayu@linux.vnet.ibm.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Pull powerpc updates from Ben Herrenschmidt:
"Here is the bulk of the powerpc changes for this merge window. It got
a bit delayed in part because I wasn't paying attention, and in part
because I discovered I had a core PCI change without a PCI maintainer
ack in it. Bjorn eventually agreed it was ok to merge it though we'll
probably improve it later and I didn't want to rebase to add his ack.
There is going to be a bit more next week, essentially fixes that I
still want to sort through and test.
The biggest item this time is the support to build the ppc64 LE kernel
with our new v2 ABI. We previously supported v2 userspace but the
kernel itself was a tougher nut to crack. This is now sorted mostly
thanks to Anton and Rusty.
We also have a fairly big series from Cedric that add support for
64-bit LE zImage boot wrapper. This was made harder by the fact that
traditionally our zImage wrapper was always 32-bit, but our new LE
toolchains don't really support 32-bit anymore (it's somewhat there
but not really "supported") so we didn't want to rely on it. This
meant more churn that just endian fixes.
This brings some more LE bits as well, such as the ability to run in
LE mode without a hypervisor (ie. under OPAL firmware) by doing the
right OPAL call to reinitialize the CPU to take HV interrupts in the
right mode and the usual pile of endian fixes.
There's another series from Gavin adding EEH improvements (one day we
*will* have a release with less than 20 EEH patches, I promise!).
Another highlight is the support for the "Split core" functionality on
P8 by Michael. This allows a P8 core to be split into "sub cores" of
4 threads which allows the subcores to run different guests under KVM
(the HW still doesn't support a partition per thread).
And then the usual misc bits and fixes ..."
[ Further delayed by gmail deciding that BenH is a dirty spammer.
Google knows. ]
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (155 commits)
powerpc/powernv: Add missing include to LPC code
selftests/powerpc: Test the THP bug we fixed in the previous commit
powerpc/mm: Check paca psize is up to date for huge mappings
powerpc/powernv: Pass buffer size to OPAL validate flash call
powerpc/pseries: hcall functions are exported to modules, need _GLOBAL_TOC()
powerpc: Exported functions __clear_user and copy_page use r2 so need _GLOBAL_TOC()
powerpc/powernv: Set memory_block_size_bytes to 256MB
powerpc: Allow ppc_md platform hook to override memory_block_size_bytes
powerpc/powernv: Fix endian issues in memory error handling code
powerpc/eeh: Skip eeh sysfs when eeh is disabled
powerpc: 64bit sendfile is capped at 2GB
powerpc/powernv: Provide debugfs access to the LPC bus via OPAL
powerpc/serial: Use saner flags when creating legacy ports
powerpc: Add cpu family documentation
powerpc/xmon: Fix up xmon format strings
powerpc/powernv: Add calls to support little endian host
powerpc: Document sysfs DSCR interface
powerpc: Fix regression of per-CPU DSCR setting
powerpc: Split __SYSFS_SPRSETUP macro
arch: powerpc/fadump: Cleaning up inconsistent NULL checks
...
- BSC9132 is an integrated device that targets Femto base station market.
It combines Power Architecture e500v2 and DSP StarCore SC3850 technologies
with MAPLE-B2F baseband acceleration processing elements
- BSC9132QDS Overview
2Gbyte DDR3 (on board DDR)
32Mbyte 16bit NOR flash
128Mbyte 2K page size NAND Flash
256 Kbit M24256 I2C EEPROM
128 Mbit SPI Flash memory
SD slot
eTSEC1: Connected to SGMII PHY
eTSEC2: Connected to SGMII PHY
DUART interface: supports one UARTs up to 115200 bps for console display
Signed-off-by: Harninder Rai <harninder.rai@freescale.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
P1023RDS is no longer supported/manufactured by Freescale while P1023RDB is.
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add support for T104x board in board file t104x_qds.c, It is common for
both T1040 and T1042 as they share same QDS board.
T1040QDS board Overview
-----------------------
- SERDES Connections, 8 lanes supporting:
— PCI Express: supporting Gen 1 and Gen 2;
— SGMII
— QSGMII
— SATA 2.0
— Aurora debug with dedicated connectors (T1040 only)
- DDR Controller
- Supports rates of up to 1600 MHz data-rate
- Supports one DDR3LP UDIMM/RDIMMs, of single-, dual- or quad-rank types.
-IFC/Local Bus
- NAND flash: 8-bit, async, up to 2GB.
- NOR: 8-bit or 16-bit, non-multiplexed, up to 512MB
- GASIC: Simple (minimal) target within Qixis FPGA
- PromJET rapid memory download support
- Ethernet
- Two on-board RGMII 10/100/1G ethernet ports.
- PHY #0 remains powered up during deep-sleep (T1040 only)
- QIXIS System Logic FPGA
- Clocks
- System and DDR clock (SYSCLK, “DDRCLK”)
- SERDES clocks
- Power Supplies
- Video
- DIU supports video at up to 1280x1024x32bpp
- USB
- Supports two USB 2.0 ports with integrated PHYs
— Two type A ports with 5V@1.5A per port.
— Second port can be converted to OTG mini-AB
- SDHC
- SDHC port connects directly to an adapter card slot, featuring:
- Supporting SD slots for: SD, SDHC (1x, 4x, 8x) and/or MMC
— Supporting eMMC memory devices
- SPI
- On-board support of 3 different devices and sizes
- Other IO
- Two Serial ports
- ProfiBus port
- Four I2C ports
Add T104xQDS support in Kconfig and Makefile. Also create device tree.
Following features are currently not implmented.
- SerDes: Aurora
- IFC: GASIC, Promjet
- QIXIS
- Ethernet
- DIU
- power supplies management
- ProfiBus
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The QorIQ T1040/T1042 processor support four integrated 64-bit e5500 PA
processor cores with high-performance data path acceleration architecture
and network peripheral interfaces required for networking & telecommunications.
T1042 personality is a reduced personality of T1040 without Integrated 8-port
Gigabit Ethernet switch.
The T1040/T1042 SoC includes the following function and features:
- Four e5500 cores, each with a private 256 KB L2 cache
- 256 KB shared L3 CoreNet platform cache (CPC)
- Interconnect CoreNet platform
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving
support
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
for the following functions:
- Packet parsing, classification, and distribution
- Queue management for scheduling, packet sequencing, and congestion
management
- Cryptography Acceleration (SEC 5.0)
- RegEx Pattern Matching Acceleration (PME 2.2)
- IEEE Std 1588 support
- Hardware buffer management for buffer allocation and deallocation
- Ethernet interfaces
- Integrated 8-port Gigabit Ethernet switch (T1040 only)
- Four 1 Gbps Ethernet controllers
- Two RGMII interfaces or one RGMII and one MII interfaces
- High speed peripheral interfaces
- Four PCI Express 2.0 controllers running at up to 5 GHz
- Two SATA controllers supporting 1.5 and 3.0 Gb/s operation
- Upto two QSGMII interface
- Upto six SGMII interface supporting 1000 Mbps
- One SGMII interface supporting upto 2500 Mbps
- Additional peripheral interfaces
- Two USB 2.0 controllers with integrated PHY
- SD/eSDHC/eMMC
- eSPI controller
- Four I2C controllers
- Four UARTs
- Four GPIO controllers
- Integrated flash controller (IFC)
- Change this to LCD/ HDMI interface (DIU) with 12 bit dual data rate
- TDM interface
- Multicore programmable interrupt controller (PIC)
- Two 8-channel DMA engines
- Single source clocking implementation
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Updated the device trees according to the corenet-cf
binding definition.
Signed-off-by: Diana Craciun <Diana.Craciun@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Updated the device trees according to the corenet-cf
binding definition.
Signed-off-by: Diana Craciun <Diana.Craciun@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch introduces the support for Keymile's kmcoge4 board which is
the internal reference design for boards based on Freescale's
P2040/P2041 SoCs. This internal reference design is named kmp204x.
The peripherals used on this board are:
- SPI NOR Flash as bootloader medium
- NAND Flash with a ubi partition
- 2 PCIe busses (hosts 1 and 3)
- 3 FMAN Ethernet devices (FMAN1 DTSEC1/2/5)
- 4 Local Bus windows, with one dedicated to the QRIO reset/power mgmt
CPLD
- 2 I2C busses
- last but not least, the mandatory serial port
The patch also adds a defconfig file for this reference design that is
necessary because of the lowmem option that must be set higher due to
the number of PCIe devices with big ioremapped mem ranges on the boad.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This series adds support for building the powerpc 64-bit
LE kernel using the new ABI v2. We already supported
running ABI v2 userspace programs but this adds support
for building the kernel itself using the new ABI.
MPC512x and MPC8308 have similar DMA controllers, but are independent SoCs.
DMA controller driver should have separate 'compatible' values for these SoCs.
Signed-off-by: Alexander Popov <a13xp0p0v88@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The PPC476GTR SoC supports message signalled interrupts (MSI) by writing
to special addresses within the High Speed Transfer Assist (HSTA) module.
This patch adds support for PCI MSI with a new system device. The DMA
window is also updated to allow access to the entire 42-bit address range
to allow PCI devices write access to the HSTA module.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds support for the IBM Akebono board.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The code is only slightly modified : entry points now use the
FIXUP_ENDIAN trampoline to switch endian order. The 32bit wrapper
is kept for big endian kernels and 64bit is enforced for little
endian kernels with a PPC64_BOOT_WRAPPER config option.
The linker script is generated using the kernel preprocessor flags
to make use of the CONFIG_* definitions and the wrapper script is
modified to take into account the new elf64ppc format.
Finally, the zImage file is compiled as a position independent
executable (-pie) which makes it loadable at any address by the
firmware.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When entering the boot wrapper in little endian, we will need to fix
the endian order using a fixup trampoline like in the kernel. This
patch overrides the _zimage_start entry point for this purpose.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds support a 64bit wrapper entry point. As in 32bit, the
entry point does its own relocation and can be loaded at any address
by the firmware.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch defines a 'prom' routine similar to 'enter_prom' in the
kernel.
The difference is in the MSR which is built before entering prom. Big
endian order is enforced as in the kernel but 32bit mode is not. It
prepares ground for the next patches which will introduce Little endian
order.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It could certainly be improved using Elf macros and byteswapping
routines, but the initial version of the code is organised to be a
single file program with limited dependencies. yaboot is the same.
Please scream if you want a total rewrite.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These are not the most efficient versions of swab but the wrapper does
not do much byte swapping. On a big endian cpu, these routines are
a no-op.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
arch/powerpc/boot/oflib.c:211:9: warning: cast to pointer from integer of \
different size [-Wint-to-pointer-cast]
return (phandle) of_call_prom("finddevice", 1, 1, name);
This is a work around. The definite solution would be to define the
phandle typedef as a u32, as in the kernel, but this would break the
device tree ops API.
Let it be for the moment.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch fixes 64bit compile warnings and updates the wrapper code
to converge the kernel code in prom_init.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is mostly useful to make to the boot wrapper code closer with
the kernel code in prom_init.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Values will need to be byte-swapped when calling prom (big endian) from
a little endian boot wrapper.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch updates the wrapper code to converge with the kernel code in
prom_init.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch fixes warnings when the wrapper is compiled in 64bit and
updates the boot wrapper code related to prom to converge with the
kernel code in prom_init. This should make the review of changes easier.
The kernel has a different number of possible arguments (10) when
entering prom. There does not seem to be any good reason to have
12 in the wrapper, so the patch changes this value to args[10] in
the prom_args struct.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When the boot wrapper is compiled in 64bit, there is no need to
use __div64_32.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Bump the boot wrapper BOOT_COMMAND_LINE_SIZE to match the
kernel.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have two definitions of COMMAND_LINE_SIZE, one for the kernel
and one for the boot wrapper. I assume this is so the boot
wrapper can be self sufficient and not rely on kernel headers.
Having two defines with the same name is confusing, I just
updated the wrong one when trying to bump it.
Make the boot wrapper define unique by calling it
BOOT_COMMAND_LINE_SIZE.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
binutils is smart enough to know that a branch to a function
descriptor is actually a branch to the functions text address.
Alan tells me that binutils has been doing this for 9 years.
Signed-off-by: Anton Blanchard <anton@samba.org>
Add power sensor chip ina220 node in dts to support
power monitor
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The following SoCs will be affected: p2041, p3041, p4080,
p5020, p5040, b4420, b4860, t4240
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This processor/memory module was mostly used on ATCA blades and
before that, on cPCI blades. It wasn't really user friendly, with
custom non u-boot bootloaders (powerboot/motload) and no real way
to recover corrupted boot flash (which was a common problem).
As such, it had its day back before the big ppc --> powerpc move
to device trees, and that was largely through commercial BSPs that
started to dry up around 2007.
Systems using one were largely in a "deploy and sustain" mode,
so interest in upgrading to new kernels in the field was nil.
Also, requiring 50A, 48V power supplies and a 2'x2'x2' ATCA
chassis largely rules out any hobbyist/enthusiast interest.
The point of all this, is that we might as well delete the in
kernel files relating to this platform. No point in continuing
to build it via walking the defconfigs or via linux-next testing.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
<<
Switch mpc512x to the common clock framework and adapt mpc512x
drivers to use the new clock driver. Old PPC_CLOCK code is
removed entirely since there are no users any more.
>>
Pull powerpc updates from Ben Herrenschmidt:
"So here's my next branch for powerpc. A bit late as I was on vacation
last week. It's mostly the same stuff that was in next already, I
just added two patches today which are the wiring up of lockref for
powerpc, which for some reason fell through the cracks last time and
is trivial.
The highlights are, in addition to a bunch of bug fixes:
- Reworked Machine Check handling on kernels running without a
hypervisor (or acting as a hypervisor). Provides hooks to handle
some errors in real mode such as TLB errors, handle SLB errors,
etc...
- Support for retrieving memory error information from the service
processor on IBM servers running without a hypervisor and routing
them to the memory poison infrastructure.
- _PAGE_NUMA support on server processors
- 32-bit BookE relocatable kernel support
- FSL e6500 hardware tablewalk support
- A bunch of new/revived board support
- FSL e6500 deeper idle states and altivec powerdown support
You'll notice a generic mm change here, it has been acked by the
relevant authorities and is a pre-req for our _PAGE_NUMA support"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (121 commits)
powerpc: Implement arch_spin_is_locked() using arch_spin_value_unlocked()
powerpc: Add support for the optimised lockref implementation
powerpc/powernv: Call OPAL sync before kexec'ing
powerpc/eeh: Escalate error on non-existing PE
powerpc/eeh: Handle multiple EEH errors
powerpc: Fix transactional FP/VMX/VSX unavailable handlers
powerpc: Don't corrupt transactional state when using FP/VMX in kernel
powerpc: Reclaim two unused thread_info flag bits
powerpc: Fix races with irq_work
Move precessing of MCE queued event out from syscall exit path.
pseries/cpuidle: Remove redundant call to ppc64_runlatch_off() in cpu idle routines
powerpc: Make add_system_ram_resources() __init
powerpc: add SATA_MV to ppc64_defconfig
powerpc/powernv: Increase candidate fw image size
powerpc: Add debug checks to catch invalid cpu-to-node mappings
powerpc: Fix the setup of CPU-to-Node mappings during CPU online
powerpc/iommu: Don't detach device without IOMMU group
powerpc/eeh: Hotplug improvement
powerpc/eeh: Call opal_pci_reinit() on powernv for restoring config space
powerpc/eeh: Add restore_config operation
...
device_type is deprecated. There is no need to check for it in device
driver code and no need to specify it in the device tree. Remove the
property from stock .dts files and remove the check for it from device
drivers. This change should be 100% backwards compatible with old device
trees.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
device_type is a deprecated property, but some MDIO bus nodes still have
it. Except for a couple of old binding (compatible="gianfar" and
compatible="ucc_geth_phy") the kernel doesn't look for
device_type="mdio" at all.
This patch removes all instances of device_type="mdio" from the binding
documentation and the .dts files.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The device_type property is deprecated for the flattened device tree and
the value "ethernet-phy" has never been defined as having a useful
meaning. Neither the kernel nor u-boot depend on it. It should never
have appeared in PHY bindings. This patch removes all references to
"ethernet-phy" as a device_type value from the documentation and the
.dts files.
This patch was generated mechanically with the following command and
then verified by looking at the diff.
sed -i '/"ethernet-phy"/d' `git grep -l '"ethernet-phy"'`
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
this addresses the client side of device tree based clock lookups
add clock specifiers to the mbx, nfc, mscan, sdhc, i2c, axe, diu, viu,
mdio, fec, usb, pata, psc, psc fifo, and pci nodes in the shared
mpc5121.dtsi include
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: devicetree@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
this addresses the clock driver aka provider's side of clocks
- introduce a 'clocks' subtree with an 'osc' node for the crystal
or oscillator SoC input (fixed frequency)
- the 'clock@f00' clock-control-module node references the 'osc' for
its input, and is another provider for all the clocks which the
CCM component manages
- prepare for future references to clocks from peripheral nodes
by means of the <&clks ID> syntax and symbolic ID names which a
header file provides
- provide default values with 33MHz oscillator frequency in the
common include (the 66MHz IPS bus already was there), and add
override values for the ifm AC14xx board which deviates from
the reference design (25MHz xtal, 80MHz IPS bus)
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add elo3-dma-2.dtsi to support the third DMA controller.
This is used on T2080, T4240, B4860, etc.
FSL MPIC v4.3 adds a new discontiguous address range for internal interrupts,
e.g. internal interrupt 0 is at offset 0x200 and thus interrupt number is:
0x200 >> 5 = 16 in the device tree. DMA controller 3 channel 0 internal
interrupt 240 is at offset 0x3a00, and thus the corresponding interrupt
number is: 0x3a00 >> 5 = 464, it's similar for other 7 interrupt numbers
of DMA 3 channels.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Hongbo Zhang <hongbo.zhang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
As of commit b81f18e55e ("powerpc/boot:
Only build board support files when required.") the two defconfigs
ep88xc_defconfig and storcenter_defconfig would fail final link as
follows:
WRAP arch/powerpc/boot/dtbImage.ep88xc
arch/powerpc/boot/wrapper.a(mpc8xx.o): In function `mpc885_get_clock':
arch/powerpc/boot/mpc8xx.c:30: undefined reference to `fsl_get_immr'
make[1]: *** [arch/powerpc/boot/dtbImage.ep88xc] Error 1
...and...
WRAP arch/powerpc/boot/cuImage.storcenter
arch/powerpc/boot/cuboot-pq2.o: In function `pq2_platform_fixups':
cuboot-pq2.c:(.text+0x324): undefined reference to `fsl_get_immr'
make[1]: *** [arch/powerpc/boot/cuImage.storcenter] Error 1
We need the fsl-soc board files built for these two platforms.
Cc: Tony Breeds <tony@bakeyournoodle.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fixes: b81f18e55e ("powerpc/boot: Only build board support files when required.")
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
P1020, P1021, P1022, P1023 when the lbc get error, the error
interrupt will be triggered. The corresponding interrupt is
internal IRQ0. So system have to process the lbc IRQ0 interrupt.
The corresponding lbc general interrupt is internal IRQ3.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
[scottwood@freescale.com: bracketed individual list elements]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add support for the Motorola/Emerson MVME5100 Single Board Computer.
The MVME5100 is a 6U form factor VME64 computer with:
- A single MPC7410 or MPC750 CPU
- A HAWK Processor Host Bridge (CPU to PCI) and
MultiProcessor Interrupt Controller (MPIC)
- Up to 500Mb of onboard memory
- A M48T37 Real Time Clock (RTC) and Non-Volatile Memory chip
- Two 16550 compatible UARTS
- Two Intel E100 Fast Ethernets
- Two PCI Mezzanine Card (PMC) Slots
- PPCBug Firmware
The HAWK PHB/MPIC is compatible with the MPC10x devices.
There is no onboard disk support. This is usually provided by installing a PMC
in first PMC slot.
This patch revives the board support, it was present in early 2.6
series kernels. The board support in those days was by Matt Porter of
MontaVista Software.
CSC Australia has around 31 of these boards in service. The kernel in use
for the boards is based on 2.6.31. The boards are operated without disks
from a file server.
This patch is based on linux-3.13-rc2 and has been boot tested.
Only boards with 512 Mb of memory are known to work.
Signed-off-by: Stephen Chivers <schivers@csc.com>
Tested-by: Alessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add an external interrupt for rtc node.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
RTC Hardware(ds3232) and rtc compatible string does not match.
Change "dallas,ds1339" to "dallas,ds3232".
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
It is not correct according to p1010rdb-pa user guide.
So modify it.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
TWR-P1025 Overview
-----------------
512Mbyte DDR3 (on board DDR)
64MB Nor Flash
eTSEC1: Connected to RGMII PHY AR8035
eTSEC3: Connected to RGMII PHY AR8035
Two USB2.0 Type A
One microSD Card slot
One mini-PCIe slot
One mini-USB TypeB dual UART
Signed-off-by: Michael Johnston <michael.johnston@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
[scottwood@freescale.com: use pr_info rather than KERN_INFO]
Signed-off-by: Scott Wood <scottwood@freescale.com>
P1010rdb-pa and p1010rdb-pb have different mtd of nand.
So update dts to adapt to both p1010rdb-pa and p1010rdb-pb.
Move the nand-mtd from p1010rdb.dtsi to p1010rdb-pa*.dts.
Remove nand-mtd for p1010rdb-pb, whick will use mtdparts
from u-boot instead of nand-mtd in device tree.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
P1010rdb-pa and p1010rdb-pb have different phy interrupts.
So update dts to adapt to both p1010rdb-pa and p1010rdb-pb.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Merge a pile of fixes that went into the "merge" branch (3.13-rc's) such
as Anton Little Endian fixes.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
At the moment the USB controller's pin muxing is not setup
correctly and causes a kernel panic upon system startup, so
disable the USB1 device tree node in the MPC5125 tower board
dts file.
The USB controller is connected to an USB3320 ULPI transceiver
and the device tree should receive an update to reflect correct
dependencies and required initialization data before the USB1
node can get re-enabled.
Signed-off-by: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
the 'soc' node in the MPC5125 "tower" board .dts has an '#interrupt-cells'
property although this node is not an interrupt controller
remove this erroneously placed property because starting with v3.13-rc1
lookup and resolution of 'interrupts' specs for peripherals gets misled
(tries to use the 'soc' as the interrupt parent which fails), emits
'no irq domain found' WARN() messages and breaks the boot process
[ best viewed with 'git diff -U5' to have DT node names in the context ]
Cc: Anatolij Gustschin <agust@denx.de>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This fixes a warning:
DTC arch/powerpc/boot/virtex440-ml507.dtb
Warning (reg_format): "reg" property in /plb@0/xps-ll-temac@81c00000/ethernet@81c00000/phy@7 has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells value for /plb@0/xps-ll-temac@81c00000/ethernet@81c00000/phy@7
Warning (avoid_default_addr_size): Relying on default #size-cells value for /plb@0/xps-ll-temac@81c00000/ethernet@81c00000/phy@7
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Gernot Vormayr <gvormayr@gmail.com>
Cc: devicetree@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently I see:
DTC arch/powerpc/boot/kilauea.dtb
Warning (reg_format): "reg" property in /plb/ppc4xx-msi@C10000000 has invalid length (12 bytes) (#address-cells == 1, #size-cells == 1)
It appears that unlike the other platforms handled by 3fb7933850
"powerpc/4xx: Adding PCIe MSI support" this platform does not use address-cells=2.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Josh Boyer <jwboyer@gmail.com>
Cc: Rupjyoti Sarmah <rsarmah@apm.com>
Cc: Tirumala R Marri <tmarri@apm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: devicetree@vger.kernel.org (open list:OPEN FIRMWARE AND...)
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These lines were inoperative for four years, which puts some doubt into
their importance, and it's possible the fixed version will regress, but
at the very least they should be removed instead.
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Commit beb2dc0a7a breaks the MPC8xx which
seems to not support using mfspr SPRN_TBRx instead of mftb/mftbu
despite what is written in the reference manual.
This patch reverts to the use of mftb/mftbu when CONFIG_8xx is
selected.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Pull slave-dmaengine changes from Vinod Koul:
"This brings for slave dmaengine:
- Change dma notification flag to DMA_COMPLETE from DMA_SUCCESS as
dmaengine can only transfer and not verify validaty of dma
transfers
- Bunch of fixes across drivers:
- cppi41 driver fixes from Daniel
- 8 channel freescale dma engine support and updated bindings from
Hongbo
- msx-dma fixes and cleanup by Markus
- DMAengine updates from Dan:
- Bartlomiej and Dan finalized a rework of the dma address unmap
implementation.
- In the course of testing 1/ a collection of enhancements to
dmatest fell out. Notably basic performance statistics, and
fixed / enhanced test control through new module parameters
'run', 'wait', 'noverify', and 'verbose'. Thanks to Andriy and
Linus [Walleij] for their review.
- Testing the raid related corner cases of 1/ triggered bugs in
the recently added 16-source operation support in the ioatdma
driver.
- Some minor fixes / cleanups to mv_xor and ioatdma"
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (99 commits)
dma: mv_xor: Fix mis-usage of mmio 'base' and 'high_base' registers
dma: mv_xor: Remove unneeded NULL address check
ioat: fix ioat3_irq_reinit
ioat: kill msix_single_vector support
raid6test: add new corner case for ioatdma driver
ioatdma: clean up sed pool kmem_cache
ioatdma: fix selection of 16 vs 8 source path
ioatdma: fix sed pool selection
ioatdma: Fix bug in selftest after removal of DMA_MEMSET.
dmatest: verbose mode
dmatest: convert to dmaengine_unmap_data
dmatest: add a 'wait' parameter
dmatest: add basic performance metrics
dmatest: add support for skipping verification and random data setup
dmatest: use pseudo random numbers
dmatest: support xor-only, or pq-only channels in tests
dmatest: restore ability to start test at module load and init
dmatest: cleanup redundant "dmatest: " prefixes
dmatest: replace stored results mechanism, with uniform messages
Revert "dmatest: append verify result to results"
...
Freescale QorIQ T4 and B4 introduce new 8-channel DMA engines, this patch adds
the device tree nodes for them.
Signed-off-by: Hongbo Zhang <hongbo.zhang@freescale.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The wrapper script needs an explicit rule for the "of" boot
wrapper (generic wrapper, similar to pseries). Before
0c9fa29149 it was hanlded
implicitly by the statement:
platformo=$object/"$platform".o
But now that epapr.o needs to be added, that doesn't work
and an explicit rule must be added.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit c55aef0e5b ("powerpc/boot: Change the load address for the
wrapper to fit the kernel") adjusts the wrapper address unnecessarily
for platforms that use arch/powerpc/boot/of.c, since the code there
allocates space for the kernel wherever it can find it and doesn't
necessarily load the kernel at address 0. Changing the link address
is actually harmful since it can cause the zImage to overlap with
Open Firmware and thus fail to boot.
To fix this, we set make_space to n for all of the platforms that
use of.o.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
C290PCIe has NAND flash present on IFC Chip Select(CS) 1.
So Add "ranges" field for NAND flash on CS1.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
B4860EMU is a emualtor target with minimum peripherals. It is based on
B4860QDS and trimmed down most peripherals due to either not modeled or
lack of board level connections. The main purpose of this minimum dts is
to speed up booting on emulator.
Signed-off-by: York Sun <yorksun@freescale.com>
[scottwood@freescale.com: whitespace fix]
Signed-off-by: Scott Wood <scottwood@freescale.com>
T4240EMU is an emulator target with minimum peripherals. It is based on
T4240QDS and trimmed down most peripherals due to either not modeled or
lack of board level connections. The main purpose of this minimum dts is
to speed up booting on emulator.
Signed-off-by: York Sun <yorksun@freescale.com>
[scottwood@freescale.com: whitespace fixes]
Signed-off-by: Scott Wood <scottwood@freescale.com>
In both B4 and T4240QDS platform PCA9547 I2C bus multiplexer is used.
The sub-nodes are also reorganized according to right I2C topology.
Signed-off-by: Jia Hongtao <hongtao.jia@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
We use property "sdhci,auto-cmd12" instead of "fsl,sdhci-auto-cmd12"
to distinguish if the sdhc host has quirk SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Freescale T4240QDS reference board has extra voltage shifters added
to allow 3.3V operation, so add 3.3v voltage support for T4240QDS.
1.8v and 3.3v is recommand for eMMC and SDHC card.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
bsc9131 device tree does not have these properties.
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
b4420 and b4860 device trees do not have these properties.
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
For B4 platform, MPIC EISR register is in reversed bitmap order,
instead of "Error interrupt source 0-31. Bit 0 represents SRC0."
the correct ordering is "Error interrupt source 0-31. Bit 0
represents SRC31." This patch is to fix sRIO EISR bit value
of error interrupt in dts node.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch allows the kbuild system to successfully compile a kernel
for the little endian PowerPC64 architecture. A subsequent patch
will add the CONFIG_CPU_LITTLE_ENDIAN kernel config option which
must be set to build such a kernel.
If cross compiling, CROSS_COMPILE must point to a suitable toolchain
(compiled for the powerpc64le-linux and powerpcle-linux targets).
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This makes the "OF" zImage wrapper (zImage.pseries, zImage.pmac,
zImage.maple) work if booted via a flat device-tree (ePAPR boot
mode), and thus potentially usable with kexec.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
From Anatolij:
<<
There are cleanups for some mpc5121 specific drivers and DTS files
in preparation to switch mpc5121 clock support to a clock driver
based on common clock framework. Additionally Sebastian fixed the
mpc52xx PIC driver so that it builds when using older gcc versions.
>>
C293PCIE board is a series of Freescale PCIe add-in cards to perform
as public key crypto accelerator or secure key management module.
- 512KB platform SRAM in addition to 512K L2 Cache/SRAM
- 512MB soldered DDR3 32bit memory
- CPLD System Logic
- 64MB x16 NOR flash and 4GB x8 NAND flash
- 16MB SPI flash
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Po Liu <Po.Liu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add device tree for SEC 6.0 used on C29x silicon.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Po Liu <Po.Liu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
prepare C preprocessor support when processing MPC512x DTS files
- switch from DTS syntax to CPP syntax for include specs
- create a symlink such that DTS processing can reference includes
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Some CPUs (such as e500v1/v2) don't implement mftb and will take a
trap. mfspr should work on everything that has a timebase, and is the
preferred instruction according to ISA v2.06.
Currently we get away with mftb on 85xx because the assembler converts
it to mfspr due to -Wa,-me500. However, that flag has other effects
that are undesireable for certain targets (e.g. lwsync is converted to
sync), and is hostile to multiplatform kernels. Thus we would like to
stop setting it for all e500-family builds.
mftb/mftbu instances which are in 85xx code or common code are
converted. Instances which will never run on 85xx are left alone.
Signed-off-by: Scott Wood <scottwood@freescale.com>
This is another file we can generate so add it to the list.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For the latest platform T4 and B4, MPIC controller has been updated
to v4.3. This patch adds a new file to describe the latest MPIC.
The MSI blocks number is increased to four, the registers number
of each block is increased to sixteen. MSIIR1 has been added to
access these sixteen MSI registers.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This file is a common include for B4860 and B4420 but is not a valid DTS itself:
DTC arch/powerpc/boot/b4qds.dtb
Error: arch/powerpc/boot/dts/b4qds.dts:35.1-2 syntax error
FATAL ERROR: Unable to parse input tree
make[1]: *** [arch/powerpc/boot/b4qds.dtb] Error 1
make: *** [b4qds.dtb] Error 2
I spotted in build tests of device-tree.git, announcement
https://lkml.org/lkml/2013/4/24/209, which builds *.dts. Probably no one would
do this this in real life on linux.git but it still seems worth fixing.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Shaveta Leekha <shaveta@freescale.com>
Cc: Minghuan Lian <Minghuan.Lian@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Scott Wood <scottwood@freescale.com>
The Interlaken is a narrow, high speed channelized chip-to-chip interface. To
facilitate interoperability between a data path device and a look-aside
co-processor, the Interlaken Look-Aside protocol is defined for short
transaction-related transfers. Although based on the Interlaken protocol,
Interlaken Look-Aside is not directly compatible with Interlaken and can be
considered a different operation mode.
The Interlaken LA controller connects internal platform to Interlaken serial
interface. It accepts LA command through software portals, which are system
memory mapped 4KB spaces. The LA commands are then translated into the
Interlaken control words and data words, which are sent on TX side to TCAM
through SerDes lanes.
Signed-off-by: Joe Liccese <joe.liccese@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The currituck board uses a different IRQ for the pci usb host
controller depending on the board revision. This patch adds support
for newer board revisions by retrieving the board revision from the
FPGA and mapping the appropriate IRQ.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Acked-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Core:
- Introduce MMC_CAP2_NO_PRESCAN_POWERUP to allow skipping mmc_power_up()
at boot/initialization time if it's already happened, for performance
(faster boot time) reasons.
- Fix a bit width test failure that resulted in old eMMC cards being put
into 1-bit mode when 4-bit mode was available.
- Expose fwrev/hwrev for MMCv4 parts.
- Improve card removal logic in the case where the card's removed slowly;
we were missing card removal events if the card retained contact with
the slot pads for long enough to reply to a CMD13 while being removed.
Drivers:
- davinci_mmc: Support using PIO instead of DMA.
- dw_mmc: Add support for Exynos4412.
- mxcmmc: DT support, use slot-gpio API.
- mxs-mmc: Add broken-cd/cd-inverted/non-removable DT property support.
- sdhci-sirf: New sdhci-pltfm driver for CSR SiRF SoCs:
SiRFprimaII: unicore ARM Cortex-A9
SiRFatlas6: unicore ARM Cortex-A9
SiRFmarco: dual core ARM Cortex-A9 SMP
- sdhci-tegra: Add support for Tegra114 platforms, use mmc_of_parse().
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQIcBAABAgAGBQJRfr+qAAoJEHNBYZ7TNxYMG90QALW6ArdTxkfNKNybCx/s3ttm
hyP2BB9eXF/FbZ9bGHGuv9NXV/4YZ4yr4c3yV4paOMW3s0z/+IhqajLfCgPFPCGK
MOk5GAStN/+znBjLy+5V/17EJuVpE+WVwUqDg3RafB8NGQtaClymwPg6R+SMWwL9
uiRcCVgmgzlk9l+4Z1p9wHUeQlhZQ/Okzj4CjkOpWfgsUpo0PcWQRosd+CHHirWz
iWnhFBM1cP4Nj59ashYSedu797s29pKGd31JcuWWQE228iykGfcCJWzMr9YMiU6x
LwESeuTST8b9HblI7WYnFvpVvD9qTuBkkKMIKMNb4E34xBf8+H2zUh1hK7iEnDXt
W0F1xy3WsxpJ1yF0BY9SqqnNeLpJBOenHlTZfGlf5r+kHWYUUQvvqw/ZdmWStRgv
mSoqXSmz/oM3rn1KjMritJ9oyr0EH8kHDMAsoiCF0EuGipmenFTdJJiwbh0JZJxK
bjqPUROtSK8TdPvTw1BPRX5YtJLzsG4HdsI3C8W05BTbCL9iIE1NaWP27nikPVfq
glt9EilzgR252Wc649OrB7JAHBZjlVFIndNzjziGdxNzH6m1AK05qxTL5hBvba99
plccrsVMDGWLSmsGVwz7Eo+TLflRCdtrE+7O4NrlydZzp2t24HZrMc9rN8GDWQQE
dP91YUdpDYrTsUBKiKGQ
=Pr7P
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC update from Chris Ball:
"MMC highlights for 3.10:
Core:
- Introduce MMC_CAP2_NO_PRESCAN_POWERUP to allow skipping
mmc_power_up() at boot/initialization time if it's already
happened, for performance (faster boot time) reasons.
- Fix a bit width test failure that resulted in old eMMC cards being
put into 1-bit mode when 4-bit mode was available.
- Expose fwrev/hwrev for MMCv4 parts.
- Improve card removal logic in the case where the card's removed
slowly; we were missing card removal events if the card retained
contact with the slot pads for long enough to reply to a CMD13
while being removed.
Drivers:
- davinci_mmc: Support using PIO instead of DMA.
- dw_mmc: Add support for Exynos4412.
- mxcmmc: DT support, use slot-gpio API.
- mxs-mmc: Add broken-cd/cd-inverted/non-removable DT property
support.
- sdhci-sirf: New sdhci-pltfm driver for CSR SiRF SoCs:
SiRFprimaII: unicore ARM Cortex-A9
SiRFatlas6: unicore ARM Cortex-A9
SiRFmarco: dual core ARM Cortex-A9 SMP
- sdhci-tegra: Add support for Tegra114 platforms, use
mmc_of_parse()"
* tag 'mmc-updates-for-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (66 commits)
mmc: sdhci-tegra: fix MODULE_DEVICE_TABLE
mmc: core: fix init controller performance regression, updated patch
mmc: mxcmmc: enable DMA support on mpc512x
mmc: mxcmmc: constify mxcmci_devtype
mmc: mxcmmc: use slot-gpio API for write-protect detection
mmc: mxcmmc: add mpc512x SDHC support
mmc: mxcmmc: fix race conditions for host->req and host->data access
mmc: mxcmmc: DT support
mmc: dw_mmc: let device core setup the default pin configuration
mmc: mxs-mmc: add broken-cd property
mmc: mxs-mmc: add non-removable property
mmc: mxs-mmc: add cd-inverted property
mmc: core: call pm_runtime_put_noidle in pm_runtime_get_sync failed case
mmc: mxcmmc: Fix bug when card is present during boot
mmc: core: fix performance regression initializing MMC host controllers
Revert "mmc: core: wait while adding MMC host to ensure root mounts successfully"
mmc: atmel-mci: pio hang on block errors
mmc: core: Fix bit width test failing on old eMMC cards
mmc: dw_mmc: Use pr_info instead of printk
mmc: dw_mmc: Check return value of regulator_enable
...
From Kumar Gala:
<<
Add support for T4 and B4 SoC families from Freescale, e6500 altivec
support, some various board fixes and other minor cleanups.
>>
The reg property in the pci bridge device node is used to bind this
device node to the pci bridge device. Then all the pci devices under
this bridge could use the interrupt maps defined in this device node
to do the irq translation. So if this property is missed, the pci
traditional irq mechanism will not work.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix the following errors:
Error: p1025rdb.dtsi:326.2-3 label or path, 'qe', not found
Error: p1021si-post.dtsi:242.2-3 label or path, 'qe', not found
FATAL ERROR: Syntax error parsing input tree
Signed-off-by: Zhicheng Fan <B32736@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add SDHC DMA channel description to the mpc512x device tree to enable
slave channel requesting in the mxcmmc driver.
mpc512x DMA engine doesn't support endianness conversion when
reading/writing data from peripheral's FIFO, so we have to swap data
buffers before each DMA write and after each DMA read transfer manually.
Since chained SDHC DMA transfers are not supported on mpc512x, limit
'max_segs' tunable parameter to one and initialise it to 64 only when
running on i.MX platforms.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The localbus node should be in at 0xfffe05000 not 0xffe05000. Also
fixed the names of the localbus and pci nodes to reflect the addresses
they are actually at.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The crypto node now contains a new property 'fsl,sec-era'.
This is required so that applications can retrieve era info without
having to be able to read SEC's register space.
Signed-off-by: Vakul Garg <vakul@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Removing qoriq-sec4.1-0.dtsi as it is not used by any soc anymore.
Signed-off-by: Vakul Garg <vakul@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add dts file for ac14xx board and its board compatible
string to the generic mpc512x board match list.
Also add phandle to the dma DT node since there is a change
(for MPC5121 SDHC DMA support) merged via linux-mmc tree
with reference to the dma controller node in the sdhc node.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
B4860QDS and B4420QDS share same QDS board
* common board features have been added in b4qds.dts
* various board differences are in respective files of B4860 and B4420
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
B4860 and B4420 are similar that share some commonalities
* common features have been added in b4si-pre.dtsi and b4si-post.dtsi
* differences are added in respective silicon files of B4860 and B4420
There are several things missing from the device trees of B4860 and B4420:
* DPAA related nodes (Qman, Bman, Fman, Rman)
* DSP related nodes/information
* serdes, sfp(security fuse processor), thermal,
gpio, maple, cpri, quad timers nodes
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Vakul Garg <vakul@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Fix cpu unit address to match reg
* Update compatible for rcpm & clockgen to be 2.0 instead of 2
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
As the T4240 is based on corenet chassis v2.0 spec we update the global
utilities (GUTS) device config compatiable to reflect this.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Identifies the epu as compatible with Chassis v1 Debug IP.
Signed-off-by: Stephen George <Stephen.George@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Due to the partition of JFFS2 overlaps with QE ucode firmware, So JFFS2
will break QE ucode. Shrink JFFS2's partition to reserve the space of
QE ucode firmware.
Signed-off-by: Jiucheng Xu <Jiucheng.Xu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add first usb controller node for qonverge qoriq platforms like
B4860, etc
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable a baseline T4240 SoC to boot. There are several things missing
from the device trees for T4240:
* Proper PAMU topology information
* DPAA related nodes (Qman, Bman, Fman, Rman, DCE)
* Prefetch Manager
* Thermal monitor unit
* Interlaken
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Vakul Garg <vakul@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add device tree for SEC (crypto engine) version 5.0 used on T4240.
Signed-off-by: Vakul Garg <vakul@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
-also define a binding for fsl,eref-* properties
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
<<
Please pull mpc5xxx patches for v3.9. The bestcomm driver is
moved to drivers/dma (so it will be usable for ColdFire).
mpc5121 now provides common dtsi file and existing mpc5121 device
trees use it. There are some minor clock init and sparse fixes
and updates for various 5200 device tree files from Grant. Some
fixes for bugs in the mpc5121 DIU driver are also included here
(Andrew Morton suggested to push them via my mpc5xxx tree).
>>
BSC9131RDB doesn't have SDHC enabled. As a result of this typo,
the node was not getting disabled from the device tree which was
leading to linux hang during bootup
Signed-off-by: Harninder Rai <harninder.rai@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Initial board support for the Prodrive PPA8548 AMC module. Board
is an MPC8548 AMC platform used in RapidIO systems. This module is
also used to test/work on mainline linux RapidIO software.
PPA8548 overview:
- 1.3 GHz Freescale PowerQUICC III MPC8548 processor
- 1 GB DDR2 @ 266 MHz
- 8 MB NOR flash
- Serial RapidIO 1.2
- 1 x 10/100/1000 BASE-T front ethernet
- 1 x 1000 BASE-BX ethernet on AMC connector
Signed-off-by: Stef van Os <stef.van.os@prodrive.nl>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This facilitates getting the physical address of the SEC node.
Signed-off-by: Liu po <po.liu@freescale.com>
Reviewed-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix and/or improve the compatible strings of the PCI device tree nodes for
some Freescale SOCs. This fixes some issues and improves consistency among
the SOCs.
Specifically:
1) The P1022 has a v1 PCIe controller, so the compatible property should just
say "fsl,mpc8548-pcie". U-Boot does not look for "fsl,p1022-pcie", so it
wasn't fixing up the node.
2) The P4080 has a v2.1 PCIe controller, so add that version-specific string
to the device tree. Update the kernel to also look for that string.
Currently, the kernel looks for "fsl,p4080-pcie" specifically, but
eventually that check should be deleted.
3) The P1010 device tree claims compatibility with v2.2 and v2.3, but that's
redundant. No other device tree does this. Remove the v2.2 string.
4) The kernel looks for both "fsl,p1023-pcie" and "fsl,qoriq-pcie-v2.2",
even though the P1023 device trees has always included both strings. Remove
the search for "fsl,p1023-pcie".
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PAMU caches use the LIODNs to determine which cache lines hold the
entries for the corresponding LIODs. The LIODNs must therefore be
carefully assigned to avoid cache thrashing -- two active LIODs with
LIODNs that put them in the same cache line.
Currently, LIODNs are statically assigned by U-Boot, but this has
limitations. LIODNs are assigned even for devices that may be disabled
or unused by the kernel. Static assignments also do not allow for device
drivers which may know which LIODs can be used simultaneously. In
other words, we really should assign LIODNs dynamically in Linux.
To do that, we need to describe the PAMU device and cache topologies in
the device trees.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Stuart Yoder <stuart.yoder@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
By moving the two JP12 jumpers 90 degrees, and switching the
setting of SW2.8, the sbc8548 can be configured to boot off
the alternate 64MB SODIMM, which when populated with u-boot
can be a handy recovery option, in case the u-boot in the
8MB soldered on flash gets corrupted. Here we add an alternate
dts file to match that configuration.
To better highlight the differences, the output from the u-boot
"fli" command is shown for the normal configuration and then
the alternate configuration.
Normal:
-----------------------
Bank # 1: CFI conformant flash (8 x 8) Size: 8 MB in 64 Sectors
Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x17
Erase timeout: 4096 ms, write timeout: 1 ms
Buffer write timeout: 2 ms, buffer size: 32 bytes
Sector Start Addresses:
FF800000 E FF820000 E FF840000 E FF860000 E FF880000 E
[...]
FFEE0000 E FFF00000 E FFF20000 E FFF40000 E FFF60000 E
FFF80000 FFFA0000 RO FFFC0000 RO FFFE0000 RO
Bank # 2: CFI conformant flash (32 x 8) Size: 64 MB in 128 Sectors
Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x18
Erase timeout: 4096 ms, write timeout: 1 ms
Buffer write timeout: 2 ms, buffer size: 32 bytes
Sector Start Addresses:
EC000000 E EC080000 E EC100000 E EC180000 E EC200000 E
[...]
EFC00000 E EFC80000 E EFD00000 E EFD80000 E EFE00000 E
EFE80000 E EFF00000 EFF80000
-----------------------
Alternate:
-----------------------
Bank # 1: CFI conformant flash (32 x 8) Size: 64 MB in 128 Sectors
Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x18
Erase timeout: 4096 ms, write timeout: 1 ms
Buffer write timeout: 2 ms, buffer size: 32 bytes
Sector Start Addresses:
FC000000 E FC080000 E FC100000 E FC180000 E FC200000 E
[...]
FFC00000 E FFC80000 E FFD00000 E FFD80000 E FFE00000 E
FFE80000 E FFF00000 RO FFF80000 RO
Bank # 2: CFI conformant flash (8 x 8) Size: 8 MB in 64 Sectors
Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x17
Erase timeout: 4096 ms, write timeout: 1 ms
Buffer write timeout: 2 ms, buffer size: 32 bytes
Sector Start Addresses:
EF800000 E EF820000 E EF840000 E EF860000 E EF880000 E
[...]
EFEE0000 E EFF00000 E EFF20000 E EFF40000 E EFF60000 E
EFF80000 E EFFA0000 EFFC0000 EFFE0000
-----------------------
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The original memory map for the sbc8548 had the 64MB SODIMM flash
device misaligned by 8MB to allow a window of address space for
the soldered on 8MB device -- i.e.
start end CS<n> width Desc.
----------------------------------------------------------
fb80_0000 ff7f_ffff CS6 32 SODIMM flash (64MB)
ff80_0000 ffff_ffff CS0 8 Boot flash (8MB)
However, if we want to change the configuration so that it boots
off the 64MB flash, it is in turn then aligned with a 64MB boundary,
starting at fc00_0000 (and the 8MB @ fb80_0000 -> fbff_ffff).
This makes for complicated updates, since what is the beginning
of the physical device is 8MB into its address space in the default
configuration shown above.
This issue was fixed as of u-boot commit 3fd673cf363bc86ed42eff713d4
("sbc8548: relocate 64MB user flash to sane boundary") -- in which
the SODIMM was mapped to ec00_0000 (natively aligned under efff_ffff)
and so when JP12/SW2.8 are switched, it will be a a simple 0xec --> 0xfc
mapping between the two instances.
Here we make the associated changes in the localbus flash memory
map in the dts file: indicating the 64MB device starts at ec00_0000
and that the tail end of the 64MB device (last 2 sectors) can contain
a bootloader image.
The partitions for both flash devices get a clean-up; there were
non-meaningful assignments in there that probably originated from
the MPC8548CDS on which the file was based on. Now there is just
the categorization of free space and bootloader images.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Updates to u-boot allow this board to boot off of either
the 8MB soldered on flash, or the 64MB SODIMM flash.
This is achieved by changing JP12 and SW2.8 which in turn
swaps which flash device appears on /CS0 and /CS6 respectively.
Since the flash devices are not the same size, this also
changes the MTD memory map layout on the local bus.
Here we split the common chunks out into a pre and post
include, so they can be reused by an upcoming "alternative
boot" dts file; leaving only the local bus chunk behind.
No content changes are made at this point - it is just purely
the move to using include files.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The DTC labels feature allows a dts file to reference a node without
having to reproduce the entire node hierarchy above it. We can use this
to simplify the MPC5200 board dts files by referencing the gpt nodes by
label.
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
[agust: fixed gpt7 phandle in the csi node of o2d.dtsi]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The Lite5200 evaluation board has a number of debug LEDs that Linux
doesn't know about yet. This change adds a gpio-leds stanza to the
lite5200 device tree so that the correct driver can get hooked up.
Also, make use of the dtc labels feature to reduce the number of source
lines required to add the gpio-controller property to the general
purpose timer nodes. In addition, the required #gpio-cells properties
are added to the common mpc5200b dtsi include file so that each board
doesn't need to add them explicitly. This still doesn't enable gpio
mode, 'gpio-controller' is required for that, but it means less work
needs to be done by board ports.
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This adds the marvel phy which is present on the ml507 board.
Without this ethtool causes kernel-oopses.
Tested on ml507 board.
Signed-off-by: Gernot Vormayr <gvormayr@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch consists of:
- Add driver for OCM component
- Export OCM Information at /sys/kernel/debug/ppc4xx_ocm/info
Signed-off-by: Vinh Nguyen Huu Tuong <vhtnguyen@apm.com>
Acked-by: Josh Boyer <jwboyer@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds the MPC5200B based a3m071 board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The RaidEngine is a new Freescale hardware that used for parity
computation offloading in RAID5/6.
This patch adds the device node in device tree and related binding
documentation.
Signed-off-by: Harninder Rai <harninder.rai@freescale.com>
Signed-off-by: Naveen Burmi <naveenburmi@freescale.com>
Signed-off-by: Xuelin Shi <b29237@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add a node for the pcm030-audio-fabric ASoC driver
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Pull powerpc updates from Benjamin Herrenschmidt:
"Some highlights in addition to the usual batch of fixes:
- 64TB address space support for 64-bit processes by Aneesh Kumar
- Gavin Shan did a major cleanup & re-organization of our EEH support
code (IBM fancy PCI error handling & recovery infrastructure) which
paves the way for supporting different platform backends, along
with some rework of the PCIe code for the PowerNV platform in order
to remove home made resource allocations and instead use the
generic code (which is possible after some small improvements to it
done by Gavin).
- Uprobes support by Ananth N Mavinakayanahalli
- A pile of embedded updates from Freescale folks, including new SoC
and board supports, more KVM stuff including preparing for 64-bit
BookE KVM support, ePAPR 1.1 updates, etc..."
Fixup trivial conflicts in drivers/scsi/ipr.c
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (146 commits)
powerpc/iommu: Fix multiple issues with IOMMU pools code
powerpc: Fix VMX fix for memcpy case
driver/mtd:IFC NAND:Initialise internal SRAM before any write
powerpc/fsl-pci: use 'Header Type' to identify PCIE mode
powerpc/eeh: Don't release eeh_mutex in eeh_phb_pe_get
powerpc: Remove tlb batching hack for nighthawk
powerpc: Set paca->data_offset = 0 for boot cpu
powerpc/perf: Sample only if SIAR-Valid bit is set in P7+
powerpc/fsl-pci: fix warning when CONFIG_SWIOTLB is disabled
powerpc/mpc85xx: Update interrupt handling for IFC controller
powerpc/85xx: Enable USB support in p1023rds_defconfig
powerpc/smp: Do not disable IPI interrupts during suspend
powerpc/eeh: Fix crash on converting OF node to edev
powerpc/eeh: Lock module while handling EEH event
powerpc/kprobe: Don't emulate store when kprobe stwu r1
powerpc/kprobe: Complete kprobe and migrate exception frame
powerpc/kprobe: Introduce a new thread flag
powerpc: Remove unused __get_user64() and __put_user64()
powerpc/eeh: Global mutex to protect PE tree
powerpc/eeh: Remove EEH PE for normal PCI hotplug
...
Pull the trivial tree from Jiri Kosina:
"Tiny usual fixes all over the place"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
doc: fix old config name of kprobetrace
fs/fs-writeback.c: cleanup riteback_sb_inodes kerneldoc
btrfs: fix the commment for the action flags in delayed-ref.h
btrfs: fix trivial typo for the comment of BTRFS_FREE_INO_OBJECTID
vfs: fix kerneldoc for generic_fh_to_parent()
treewide: fix comment/printk/variable typos
ipr: fix small coding style issues
doc: fix broken utf8 encoding
nfs: comment fix
platform/x86: fix asus_laptop.wled_type module parameter
mfd: printk/comment fixes
doc: getdelays.c: remember to close() socket on error in create_nl_socket()
doc: aliasing-test: close fd on write error
mmc: fix comment typos
dma: fix comments
spi: fix comment/printk typos in spi
Coccinelle: fix typo in memdup_user.cocci
tmiofb: missing NULL pointer checks
tools: perf: Fix typo in tools/perf
tools/testing: fix comment / output typos
...
Add common o2d dtsi file to reuse it for other configurations.
Add machine compatible string to mpc5200 simple platform file.
Add dts files for O2D, O2I, O2MNT, O2DNT2, O2D300 and O3DNT boards.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Device node adt7461 was wrongly added in p5040ds.dts, it should be added
into i2c instead of localbus, when build p5040ds.dtb, a warning will dump:
Warning (reg_format): "reg" property in
/localbus@ffe124000/nand@2,0/adt7461@4c has invalid length (4 bytes)
(#address-cells == 1, #size-cells == 1)
This was introduced by:
commit ea6b1ba692bcb5f6e39f409a78cf8b04fdf23baa
Author: Jia Hongtao <B38951@freescale.com>
Date: Tue Aug 28 10:00:55 2012 +0800
powerpc: add adt7461 thermal monitor support to applicable boards
Add thermal monitor support to following boards:
P1022DS, MPC8536DS, P2041RDB, P3041DS, P4080DS, P5020DS, P5040DS
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
create partition table for norflash.
Signed-off-by: Wang Dongsheng <Dongsheng.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add thermal monitor support to following boards:
P1022DS, MPC8536DS, P2041RDB, P3041DS, P4080DS, P5020DS, P5040DS
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
power-isa-version and power-isa-* are cpu node general properties defined
in ePAPR.
If the power-isa-version property exists, then for each category from the
Categories section of Book I of the Power ISA version indicated, the
existence of a property named power-isa-[CAT], where [CAT] is the
abbreviated category name with all uppercase letters converted to
lowercase, indicates that the category is supported by the implementation.
This patch update all the e5500 platforms.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Olivia Yin <hong-hua.yin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
power-isa-version and power-isa-* are cpu node general properties defined
in ePAPR.
If the power-isa-version property exists, then for each category from the
Categories section of Book I of the Power ISA version indicated, the
existence of a property named power-isa-[CAT], where [CAT] is the
abbreviated category name with all uppercase letters converted to
lowercase, indicates that the category is supported by the implementation.
The patch update all the e500mc platforms.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Olivia Yin <hong-hua.yin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
power-isa-version and power-isa-* are cpu node general properties defined
in ePAPR.
If the power-isa-version property exists, then for each category from the
Categories section of Book I of the Power ISA version indicated, the
existence of a property named power-isa-[CAT], where [CAT] is the
abbreviated category name with all uppercase letters converted to
lowercase, indicates that the category is supported by the implementation.
The patch update all e500v2 platforms.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Olivia Yin <hong-hua.yin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale / iVeia P1022RDK reference board is a small-factor board
with a Freescale P1022 SOC. It includes:
1) 512 MB 64-bit DDR3-800 (max) memory
2) 8MB SPI serial flash memory for boot loader
3) Bootable 4-bit SD/MMC port
4) Two 10/100/1000 Ethernet connectors
5) One SATA port
6) Two USB ports
7) One PCIe x4 slot
8) DVI video connector
9) Audio input and output jacks, powered by a Wolfson WM8960 codec.
Unlike the P1022DS, the P1022RDK does not have any localbus devices,
presumably because of the localbus / DIU multiplexing restriction of
the P1022 SOC.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for the Freescale P5040DS Reference Board ("Superhydra"), which
is similar to the P5020DS. Features of the P5040 are listed below, but
not all of these features (e.g. DPAA networking) are currently supported.
Four P5040 single-threaded e5500 cores built
Up to 2.4 GHz with 64-bit ISA support
Three levels of instruction: user, supervisor, hypervisor
CoreNet platform cache (CPC)
2.0 MB configures as dual 1 MB blocks hierarchical interconnect fabric
Two 64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
support Up to 1600MT/s
Memory pre-fetch engine
DPAA incorporating acceleration for the following functions
Packet parsing, classification, and distribution (FMAN)
Queue management for scheduling, packet sequencing and
congestion management (QMAN)
Hardware buffer management for buffer allocation and
de-allocation (BMAN)
Cryptography acceleration (SEC 5.0) at up to 40 Gbps SerDes
20 lanes at up to 5 Gbps
Supports SGMII, XAUI, PCIe rev1.1/2.0, SATA Ethernet interfaces
Two 10 Gbps Ethernet MACs
Ten 1 Gbps Ethernet MACs
High-speed peripheral interfaces
Two PCI Express 2.0/3.0 controllers
Additional peripheral interfaces
Two serial ATA (SATA 2.0) controllers
Two high-speed USB 2.0 controllers with integrated PHY
Enhanced secure digital host controller (SD/MMC/eMMC)
Enhanced serial peripheral interface (eSPI)
Two I2C controllers
Four UARTs
Integrated flash controller supporting NAND and NOR flash
DMA
Dual four channel
Support for hardware virtualization and partitioning enforcement
Extra privileged level for hypervisor support
QorIQ Trust Architecture 1.1
Secure boot, secure debug, tamper detection, volatile key storage
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add device tree (dtsi) files for the Freescale P5040 SOC. Since this
SOC introduces SEC v5.2, add the dtsi file for that also.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We only need two examples of CAMP device trees in the upstream kernel.
Co-operative Asymmetric Multi-Processing (CAMP) is a technique where two
or more operating systems (typically multiple copies of the same Linux
kernel) are loaded into memory, and each kernel is given a subset of the
available cores to execute on. For example, on a four-core system, one
kernel runs on cores 0 and 1, and the other runs on cores 2 and 3.
The devices are also partitioned among the operating systems, and this is
done with customized device trees. Each kernel gets its own device tree
that has only the devices that it should know about.
Unfortunately, this approach is very hackish. The kernels are trusted to
only access devices in their respective device trees, and the partitioning
only works for devices that can be handled. Crafting the device trees is a
tricky process, and getting U-Boot to load and start all kernels is
cumbersome.
But most importantly, each CAMP setup is very application-specific, since
the actual partitioning of resources is done in the DTS by the system
designer. Therefore, it doesn't make a lot of sense to have a lot of CAMP
device trees, since we only expect them to be used as examples.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Several files in obj-plat depend on libfdt header file. Sometimes
when building one can see the following issue. This patch adds
libfdt as dependency to those object files
| In file included from arch/powerpc/boot/treeboot-iss4xx.c:33:0:
| arch/powerpc/boot/libfdt.h:854:1: error: unterminated comment
| In file included from arch/powerpc/boot/treeboot-iss4xx.c:33:0:
| arch/powerpc/boot/libfdt.h:1:0: error: unterminated #ifndef
| BOOTCC arch/powerpc/boot/inffast.o
| make[1]: *** [arch/powerpc/boot/treeboot-iss4xx.o] Error 1
| make[1]: *** Waiting for unfinished jobs....
| BOOTCC arch/powerpc/boot/inflate.o
| make: *** [uImage] Error 2
| ERROR: oe_runmake failed
| ERROR: Function failed: do_compile (see /srv/home/pokybuild/yocto-autobuilder/yocto-slave/p1022ds/build/build/tmp/work/p1022ds-poky-linux-gnuspe/linux-qoriq-sdk-3.0.34-r5/temp/log.do_compile.2167 for further information)
NOTE: recipe linux-qoriq-sdk-3.0.34-r5: task do_compile: Failed
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 4f3865fb57 ("zlib_inflate: Upgrade
library code to a recent version") removed infblock.c, infblock.h,
infcodes.c, and infcodes.h from the tree. Remove their entries in
powerpc's .gitignore file too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add the missing usb controller version info and port0, which is
required during setup usb phy.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Default CoreNet Coherency Bus (CCB) frequency on P3041 is 750MHz, but espi
cannot work at 40MHz with this CCB frequency, so we need to slow down the
clock rate of espi to 35MHz to make it work stable at the CCB frequency.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In SGMII riser card different PHY chip are used with different external
IRQ from eTSEC. To support PHY link state auto detect in SGMII mode we
should add another group of PHY nodes for SGMII mode.
For MPC8572DS IRQ6 is used for PHY0~PHY1, IRQ7 is used for PHY2~PHY3.
For MPC8544DS and MPC8536DS IRQ6 is used for PHY0~PHY1.
For P2020DS IRQ5 is used for PHY1~PHY2.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The board is really P1021RDB-PC, so rename from p1021rdb.* to p1021rdb-pc.*
Signed-off-by: Xu Jiucheng <Jiucheng.Xu@freescale.com>
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add device tree nodes to enable ucc uart support on P1025RDB.
Signed-off-by: Zhicheng Fan <B32736@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
With 2-cell format interrupts of MSI PCIe ethernet card can not work.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
BSC9131RDB is a Freescale reference design board for BSC9131 SoC. The
BSC9131 is integrated SoC that targets Femto base station market. It
combines Power Architecture e500v2 and DSP StarCore SC3850 core
technologies with MAPLE-B2F baseband acceleration processing elements.
The BSC9131 SoC includes the following function and features:
. Power Architecture subsystem including a e500 processor with 256-Kbyte
shared L2 cache
. StarCore SC3850 DSP subsystem with a 512-Kbyte private L2 cache
. The Multi Accelerator Platform Engine for Femto BaseStation Baseband
Processing (MAPLE-B2F)
. A multi-standard baseband algorithm accelerator for Channel
Decoding/Encoding, Fourier Transforms, UMTS chip rate processing, LTE
UP/DL Channel processing, and CRC algorithms
. Consists of accelerators for Convolution, Filtering, Turbo Encoding,
Turbo Decoding, Viterbi decoding, Chiprate processing, and Matrix
Inversion operations
. DDR3/3L memory interface with 32-bit data width without ECC and 16-bit
with ECC, up to 400-MHz clock/800 MHz data rate
. Dedicated security engine featuring trusted boot
. DMA controller
. OCNDMA with four bidirectional channels
. Interfaces
. Two triple-speed Gigabit Ethernet controllers featuring network
acceleration including IEEE 1588. v2 hardware support and
virtualization (eTSEC)
. eTSEC 1 supports RGMII/RMII
. eTSEC 2 supports RGMII
. High-speed USB 2.0 host and device controller with ULPI interface
. Enhanced secure digital (SD/MMC) host controller (eSDHC)
. Antenna interface controller (AIC), supporting three industry standard
JESD207/three custom ADI RF interfaces (two dual port and one single
port) and three MAXIM's MaxPHY serial interfaces
. ADI lanes support both full duplex FDD support and half duplex TDD
support
. Universal Subscriber Identity Module (USIM) interface that facilitates
communication to SIM cards or Eurochip pre-paid phone cards
. TDM with one TDM port
. Two DUART, four eSPI, and two I2C controllers
. Integrated Flash memory controller (IFC)
. TDM with 256 channels
. GPIO
. Sixteen 32-bit timers
The DSP portion of the SoC consists of DSP core (SC3850) and various
accelerators pertaining to DSP operations.
BSC9131RDB Overview
----------------------
BSC9131 SoC
1Gbyte DDR3 (on board DDR)
128Mbyte 2K page size NAND Flash
256 Kbit M24256 I2C EEPROM
128 Mbit SPI Flash memory
USB-ULPI
eTSEC1: Connected to RGMII PHY
eTSEC2: Connected to RGMII PHY
DUART interface: supports one UARTs up to 115200 bps for console display
Linux runs on e500v2 core and access some DSP peripherals like AIC
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Akhil Goyal <Akhil.Goyal@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Rajan Srivastava <rajan.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This reverts commit 96cc017c5b.
The P3060 was cancelled before it went into production, so there's no point
in supporting it.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In order to enable the DIU video controller on the P1022DS, the FPGA needs
to be switched to "indirect mode", where the localbus is disabled and
the FPGA is accessed via writes to localbus chip select signals CS0 and CS1.
To obtain the address of CS0 and CS1, the platform driver uses an "indirect
pixis mode" device tree node. This node assumes that the localbus 'ranges'
property is sorted in chip-select order. That is, reg value 0 maps to
CS0, reg value 1 maps to CS1, etc. This is how the 'ranges' property is
supposed to be arranged.
Unfortunately, the 'ranges' property is often mis-arranged, and not just on
the P1022DS. Linux normally does not care, since it does not program the
localbus. But the indirect-mode code on the P1022DS does care.
The "proper" fix is to have U-Boot fix the 'ranges' property, but this would
be too cumbersome. The names and 'reg' properties of all the localbus
devices would also need to be updated, and determining which localbus device
maps to which chip select is board-specific.
Instead, we determine the CS0/CS1 base addresses the same way that U-boot
does -- by reading the BRx registers directly and mapping them to physical
addresses. This code is simpler and more reliable, and it does not require
a U-boot or device tree change.
Since the indirect pixis device tree node is no longer needed, the node is
deleted from the DTS.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This reference board dates back to 2004, and is largely a legacy
EOL product. The MPC8560 is a pre e500v2 CPU. The SBC8548 is
a more modern, better e500v2 target for people to use as a
reference board with today's kernels, should they require one.
Removing support for it will also allow us to remove some
sbc8560 specific quirk handling in 8250 UART code, and some
MTD mapping support.
Cc: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add EEPROM to the P1010RDB device tree.
The 24c01 acts as a memory SPD so it shouldn't be overwritten without
care.
The 24c256 is a general purpose memory.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This reverts commit 0c00f65653.
The initial commit was my fault. There are two boards out there:
P2020RDB and P2020RDB-PC. I wasn't aware of that and assumed that I have
a RDB board in front of me while I the RDB-PC. This patch makes it work
for the RDB-PC variant and breaks it for the RDB. Now there is a device
tree file available for the RDB-PC which was not there earlier. So with
this revert, everything gets back to normal :)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add spi support for mgcoge into the platform code and the dts
file. Additionaly SPIDEV is switched on in the defconfig and the
updates for the newer kernel version are committed. The SPI
interface is used to drive the Maxim DS3106 clock chip.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the RTC support into the p1022ds device tree
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Commit 430b01e8f5 ("[POWERPC] Kill
flatdevtree.c") killed the two files including flatdevtree_env.h. It was
apparently just an oversight to not kill that header too. Kill it now.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we build all board files regardless of the final zImage
target. This is sub-optimal (in terms on compilation) and leads to
problems in one platform needlessly causing failures for other
platforms.
Use the Kconfig variables to selectively construct this board files to
build.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These changes are specific to some driver that may be used by multiple
boards or socs. The most significant change in here is the move of the
samsung iommu code from a platform specific in-kernel interface to the
generic iommu subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=hgkg
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc driver specific updates from Olof Johansson:
"These changes are specific to some driver that may be used by multiple
boards or socs. The most significant change in here is the move of
the samsung iommu code from a platform specific in-kernel interface to
the generic iommu subsystem."
Fix up trivial conflicts in arch/arm/mach-exynos/Kconfig
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
mmc: dt: Consolidate DT bindings
iommu/exynos: Add iommu driver for EXYNOS Platforms
ARM: davinci: optimize the DMA ISR
ARM: davinci: implement DEBUG_LL port choice
ARM: tegra: Add SMMU enabler in AHB
ARM: tegra: Add Tegra AHB driver
Input: pxa27x_keypad add choice to set direct_key_mask
Input: pxa27x_keypad direct key may be low active
Input: pxa27x_keypad bug fix for direct_key_mask
Input: pxa27x_keypad keep clock on as wakeup source
ARM: dt: tegra: pinmux changes for USB ULPI
ARM: tegra: add USB ULPI PHY reset GPIO to device tree
ARM: tegra: don't hard-code USB ULPI PHY reset_gpio
ARM: tegra: change pll_p_out4's rate to 24MHz
ARM: tegra: fix pclk rate
ARM: tegra: reparent sclk to pll_c_out1
ARM: tegra: Add pllc clock init table
ARM: dt: tegra cardhu: basic audio support
ARM: dt: tegra30.dtsi: Add audio-related nodes
ARM: tegra: add AUXDATA required for audio
...
* drivers/mmc:
mmc: dt: Consolidate DT bindings
Also pulls in the omap/dt-missed-3.4 branch as a dependency.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch unifies the current DT MMC bindings documentation and code,
adds generic MMC DT bindings documentation, and updates .dts files for
consistency.
[cjb: typo fixes, addition of max-frequency property]
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The association in the decice tree between PCI and MSI
using fsl,msi property was an artificial one and it does
not reflect the actual hardware.
Signed-off-by: Diana CRACIUN <Diana.Craciun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
