As we reset the GPMI block at resume, the timing parameters setup by a
previous exec_op is lost. Rewriting GPMI timing registers on first exec_op
after resume fixes the problem.
Fixes: ef347c0cfd ("mtd: rawnand: gpmi: Implement exec_op")
Cc: stable@vger.kernel.org
Signed-off-by: Esben Haabendal <esben@geanix.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The commit converting the driver to DMAengine was missing the flags for
the memcpy prepare call.
It went unnoticed since the omap-dma driver was ignoring them.
Fixes: 3ed6a4d1de (" mtd: onenand: omap2: Convert to use dmaengine for memcp")
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use dma_addr_t type to pass memory address and control data in
DMA descriptor fields memory_pointer and ctrl_data_ptr
To fix warning: cast to pointer from integer of different size
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We are currently using nand_soft_waitrdy to poll the status of the NAND
flash. FMC2 enables the wait feature bit (this feature is mandatory for
the sequencer mode). By enabling this feature, we can't poll the status
of the NAND flash, the read status command is stucked in FMC2 pipeline
until R/B# signal is high, and locks the CPU bus.
To avoid to lock the CPU bus, we poll FMC2 ISR register. This register
reports the status of the R/B# signal.
Fixes: 2cd457f328 ("mtd: rawnand: stm32_fmc2: add STM32 FMC2 NAND flash controller driver")
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Here is the "big" tty and serial driver patches for 5.5-rc1. It's a bit
later in the merge window than normal as I wanted to make sure some
last-minute patches applied to it were all sane. They seem to be :)
There's a lot of little stuff in here, for the tty core, and for lots of
serial drivers:
- reverts of uartlite serial driver patches that were wrong
- msm-serial driver fixes
- serial core updates and fixes
- tty core fixes
- serial driver dma mapping api changes
- lots of other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXebFIQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylnmACgjfMcfQWa7uC9Q6m2DaQaRMaW6QoAnjg+TgBB
eW9EhvyXL2VbrsuUl+iH
=Am9O
-----END PGP SIGNATURE-----
Merge tag 'tty-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the "big" tty and serial driver patches for 5.5-rc1.
It's a bit later in the merge window than normal as I wanted to make
sure some last-minute patches applied to it were all sane. They seem
to be :)
There's a lot of little stuff in here, for the tty core, and for lots
of serial drivers:
- reverts of uartlite serial driver patches that were wrong
- msm-serial driver fixes
- serial core updates and fixes
- tty core fixes
- serial driver dma mapping api changes
- lots of other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (58 commits)
Revert "serial/8250: Add support for NI-Serial PXI/PXIe+485 devices"
vcs: prevent write access to vcsu devices
tty: vt: keyboard: reject invalid keycodes
tty: don't crash in tty_init_dev when missing tty_port
serial: stm32: fix clearing interrupt error flags
tty: Fix Kconfig indentation, continued
serial: serial_core: Perform NULL checks for break_ctl ops
tty: remove unused argument from tty_open_by_driver()
tty: Fix Kconfig indentation
{tty: serial, nand: onenand}: samsung: rename to fix build warning
serial: ifx6x60: add missed pm_runtime_disable
serial: pl011: Fix DMA ->flush_buffer()
Revert "serial-uartlite: Move the uart register"
Revert "serial-uartlite: Add get serial id if not provided"
Revert "serial-uartlite: Do not use static struct uart_driver out of probe()"
Revert "serial-uartlite: Add runtime support"
Revert "serial-uartlite: Change logic how console_port is setup"
Revert "serial-uartlite: Use allocated structure instead of static ones"
tty: serial: msm_serial: Use dma_request_chan() directly for channel request
tty: serial: tegra: Use dma_request_chan() directly for channel request
...
Any arm config which has 'CONFIG_MTD_ONENAND_SAMSUNG=m' and
'CONFIG_SERIAL_SAMSUNG=m' gives a build warning:
warning: same module names found:
drivers/tty/serial/samsung.ko
drivers/mtd/nand/onenand/samsung.ko
Rename both drivers/tty/serial/samsung.c to
drivers/tty/serial/samsung_tty.c and drivers/mtd/nand/onenand/samsung.c
drivers/mtd/nand/onenand/samsung_mtd.c to fix the warning.
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Acked-by: Richard Weinberger <richard@nod.at>
Link: https://lore.kernel.org/r/20191117202435.28127-1-sudipm.mukherjee@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Useless extra checks dropped.
* Updated the detection of the bad block markers position
Raw NAND controller drivers:
* Cadence : New driver
* Brcmnand: Support for flash-dma v0 + fixes
* Denali : Support for the legacy controller/chip DT representation
dropped
* Superfluous dev_err() calls removed
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl3KwQYACgkQJWrqGEe9
VoTj1wf/Zvnk1u2vNVUaWDaHnUTAcMvjYNr1N1ppXquRXQTknZHxcgqavcwOA3yV
inHRdjQpvTPft3Pb0tddC2VBOMQTYWDGJs6JOLiPF5c4QdW/w4yHRrdnEIumbVP/
itXySbPj2QsXcRuIoEm165NTI8mdSzZFixZvCNS58r2mvMXvQbcUHsP9vjlUs9/S
XPqBlSBPKa6hC2ToIiXhgkGDQzVJ/OkCOSgG+37ATUrEqWUi9oN2KUPkbk4HSZe9
dntUIFSjeAqGjKGRGwAlt4axhnFWABfWa9xBwX9k5s4mt/FJ9QF24geemz/F1Ljp
7xd6MJu3JYoW8qBcXRRDgHuv5RNnHA==
=rpUJ
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.5' into mtd/next
Raw NAND core
* Useless extra checks dropped.
* Updated the detection of the bad block markers position
Raw NAND controller drivers:
* Cadence : New driver
* Brcmnand: Support for flash-dma v0 + fixes
* Denali : Support for the legacy controller/chip DT representation
dropped
* Superfluous dev_err() calls removed
- introduce 'struct spi_nor_controller_ops',
- clean the Register Operations methods,
- use dev_dbg insted of dev_err for low level info,
- fix retlen handling in sst_write(),
- fix silent truncations in spi_nor_read and spi_nor_read_raw(),
- fix the clearing of QE bit on lock()/unlock(),
- rework the disabling of the block write protection,
- rework the Quad Enable methods,
- make sure nor->spimem and nor->controller_ops are mutually exclusive,
- set default Quad Enable method for ISSI flashes,
- add support for few flashes.
SPI NOR controller drivers changes:
- intel-spi:
- support chips without software sequencer,
- add support for Intel Cannon Lake and Intel Comet Lake-H flashes.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAl3Kep8ACgkQS1VPR6WN
FOn9kgf/aKPgU6LR84YpwUKRZ4S+6K1H8SdDUt8v0FYSQ6oaTjF13fApg43WDja5
Zk0l5tlX7WIvlcRC6XKPhryZTXOKWojW1X8sguPYIZGzo7q82Eyda23jkw1QptWr
VO9L/tdK4yVUbdtp6VS/FUF31PC0DtDoCzsfBSUgrZP2srFF1BtOJNUgyuDceoxo
y3hEmINDnkaOvDDl/kbJjdEHG4PV8Vi4k0KE8deLpqlp8GDG1nkTeA1Sim7WjBPA
ZZOdg9fmGI8H8+umQEnn06H4O95T2+fX+kDMCYo4RbgWyWlGv5TidgRREmC/cSbl
YEPu6LCQoUZPVEvgolr/8Akf968ZiQ==
=i15M
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.5' into mtd/next
SPI NOR core changes:
- introduce 'struct spi_nor_controller_ops',
- clean the Register Operations methods,
- use dev_dbg insted of dev_err for low level info,
- fix retlen handling in sst_write(),
- fix silent truncations in spi_nor_read and spi_nor_read_raw(),
- fix the clearing of QE bit on lock()/unlock(),
- rework the disabling of the block write protection,
- rework the Quad Enable methods,
- make sure nor->spimem and nor->controller_ops are mutually exclusive,
- set default Quad Enable method for ISSI flashes,
- add support for few flashes.
SPI NOR controller drivers changes:
- intel-spi:
- support chips without software sequencer,
- add support for Intel Cannon Lake and Intel Comet Lake-H flashes.
Remove unecessary checking if dmac is NULL.
If Cadence nand controller driver uses DMA engine then cdns_ctrl->dmac
cannot be NULL. It is verified during driver initialization.
If Cadence nand controller driver does not use DMA engine then
CPU IO read/write are executed instead of slave DMA transfer.
In that case cdns_ctrl->dmac is not used at all.
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
platform_get_irq() will call dev_err() itself on failure,
so there is no need for the driver to also do this.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
platform_get_irq() will call dev_err() itself on failure,
so there is no need for the driver to also do this.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Sparse complained about the following:
drivers/mtd/nand/raw/brcmnand/brcmnand.c:921:40: warning: Using plain integer as NULL pointer
fix this issue by assigning the pointer to NULL.
Fixes: c1ac2dc34b ("mtd: rawnand: brcmnand: When oops in progress use pio and interrupt polling")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Commit d8e8fd0ebf ("mtd: rawnand: denali: decouple controller and
NAND chips") supported the new binding for the separate controller/chip
representation, keeping the backward compatibility.
All the device trees in upstream migrated to the new binding.
Remove the support for the old binding.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Commit 7e534323c4 ("mtd: rawnand: Pass a nand_chip object to
chip->read_xxx() hooks") modified the prototype of the struct nand_chip
read_buf function pointer. In the au1550nd driver we have 2
implementations of read_buf. The previously mentioned commit modified
the au_read_buf() implementation to match the function pointer, but not
au_read_buf16(). This results in a compiler warning for MIPS
db1xxx_defconfig builds:
drivers/mtd/nand/raw/au1550nd.c:443:57:
warning: pointer type mismatch in conditional expression
Fix this by updating the prototype of au_read_buf16() to take a struct
nand_chip pointer as its first argument, as is expected after commit
7e534323c4 ("mtd: rawnand: Pass a nand_chip object to chip->read_xxx()
hooks").
Note that this shouldn't have caused any functional issues at runtime,
since the offset of the struct mtd_info within struct nand_chip is 0
making mtd_to_nand() effectively a type-cast.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 7e534323c4 ("mtd: rawnand: Pass a nand_chip object to chip->read_xxx() hooks")
Cc: stable@vger.kernel.org # v4.20+
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add new Cadence NAND driver to MTD subsystem
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Change calculating of position page containing BBM
If none of BBM flags are set then function nand_bbm_get_next_page
reports EINVAL. It causes that BBM is not read at all during scanning
factory bad blocks. The result is that the BBT table is build without
checking factory BBM at all. For Micron flash memories none of these
flags are set if page size is different than 2048 bytes.
Address this regression by:
- adding NAND_BBM_FIRSTPAGE chip flag without any condition. It solves
issue only for Micron devices.
- changing the nand_bbm_get_next_page_function. It will return 0
if no of BBM flag is set and page parameter is 0. After that modification
way of discovering factory bad blocks will work similar as in kernel
version 5.1.
Cc: stable@vger.kernel.org
Fixes: f90da7818b (mtd: rawnand: Support bad block markers in first, second or last page)
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
- boot_mem_map is removed, providing a nice cleanup made possible by the
recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs or
MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of Vincenzo
Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic SoCs.
- pte_special() is now supported for some configurations, allowing among
other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil, mostly
enabled by the inclusion of the new TCU (timer-counter unit) drivers
he's spent a very patient year or so working on. Plus some fixes for
X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXYaqpRUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN2JUQD+PQGFIlq9bo/3vLyqsXJffm+DhwVQ
4WSCSeN5brPkO8EA/153sRJBlRtG+KK5p9f7WYKUuBfbcEawuc1uwmKuy7cG
=lWlM
-----END PGP SIGNATURE-----
Merge tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Paul Burton:
"Main MIPS changes:
- boot_mem_map is removed, providing a nice cleanup made possible by
the recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs
or MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of
Vincenzo Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic
SoCs.
- pte_special() is now supported for some configurations, allowing
among other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil,
mostly enabled by the inclusion of the new TCU (timer-counter unit)
drivers he's spent a very patient year or so working on. Plus some
fixes for X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems"
* tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (89 commits)
MIPS: Detect bad _PFN_SHIFT values
MIPS: Disable pte_special() for MIPS32 with RiXi
MIPS: ralink: deactivate PCI support for SOC_MT7621
mips: compat: vdso: Use legacy syscalls as fallback
MIPS: Drop Loongson _CACHE_* definitions
MIPS: tlbex: Remove cpu_has_local_ebase
MIPS: tlbex: Simplify r3k check
MIPS: Select R3k-style TLB in Kconfig
MIPS: PCI: refactor ioc3 special handling
mips: remove ioremap_cachable
mips/atomic: Fix smp_mb__{before,after}_atomic()
mips/atomic: Fix loongson_llsc_mb() wreckage
mips/atomic: Fix cmpxchg64 barriers
MIPS: Octeon: remove duplicated include from dma-octeon.c
firmware: bcm47xx_nvram: Allow COMPILE_TEST
firmware: bcm47xx_nvram: Correct size_t printf format
MIPS: Treat Loongson Extensions as ASEs
MIPS: Remove dev_err() usage after platform_get_irq()
MIPS: dts: mscc: describe the PTP ready interrupt
MIPS: dts: mscc: describe the PTP register range
...
* Fixing typos
* Adding missing of_node_put() in various drivers
Raw NAND controller drivers:
* Macronix: new controller driver
* Omap2: Fixing the number of bitflips returned
* Brcmnand: Fix a pointer not iterating over all the page chunks
* W90x900: Driver removed
* Onenand: Fix a memory leak
* Sharpsl: Missing include guard
* STM32: Avoid warnings when building with W=1
* Ingenic: Fix a coccinelle warning
* r852: Call a helper to simplify the code
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl1ny0EACgkQJWrqGEe9
VoSToQf9Gk13+TPg8oFu6tlmxuQlNU5Dpc+4Hmiahzb1IWwo9Deh2VtZaeWLqPob
uAisb1HByUD0shgoG6cgmVajULlFpmTdfwBQCPR1Wgvq5pejoOC1MQOMexaZ7Gjx
cj4DZEk15FFSR7/zSsN78kFDLFh590hUGfBLW55qE69M5xphmb42BVQUFn44Q/N2
yBvqwUQO/h8TsOS4FXGNc1X0U2/wYQQSOZ6grN3x105cY8Rp05T15a+Qxu22cBem
5IqPY4dwOTXjY5l0mHVIiO/Jk/N9bAgMSd1a15VVukiAL3oefH/kNpsI8T5d31f2
uNONC6GhRJj8c3GDmO8gZ6skzTPhIg==
=a6jq
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/for-5.4
NAND core
* Fixing typos
* Adding missing of_node_put() in various drivers
Raw NAND controller drivers:
* Macronix: new controller driver
* Omap2: Fixing the number of bitflips returned
* Brcmnand: Fix a pointer not iterating over all the page chunks
* W90x900: Driver removed
* Onenand: Fix a memory leak
* Sharpsl: Missing include guard
* STM32: Avoid warnings when building with W=1
* Ingenic: Fix a coccinelle warning
* r852: Call a helper to simplify the code
omap_elm_correct_data() returns the number of bitflips for the whole
page. This is wrong, it should return the maximum number of bitflips
found in each ECC step.
In my case with a 4k page size NAND mtcdore reported -EUCLEAN with
only 12 bitflips on a page where we could correct up to 128 bits per
page (provided they are distributed equally on the 8 ECC steps)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In brcmstb_nand_verify_erased_page(), the ECC chunk pointer calculation
while correcting erased page bitflips is wrong, fix it.
Fixes: 02b88eea9f ("mtd: brcmnand: Add check for erased page bitflips")
Signed-off-by: Claire Lin <claire.lin@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The ARM w90x900 platform is getting removed, so this driver is obsolete.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add a driver for Macronix raw NAND controller.
Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In nand_scan_bbt(), a temporary buffer 'buf' is allocated through
vmalloc(). However, if check_create() fails, 'buf' is not deallocated,
leading to a memory leak bug. To fix this issue, free 'buf' before
returning the error.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In onenand_scan(), if CONFIG_MTD_ONENAND_VERIFY_WRITE is defined,
'this->verify_buf' is allocated through kzalloc(). However, it is not
deallocated in the following execution, if the allocation for
'this->oob_buf' fails, leading to a memory leak bug. To fix this issue,
free 'this->verify_buf' before returning the error.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Variable ret is being initialized with a value that is never read
and ret is being re-assigned a little later on. The assignment is
redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
drivers/mtd/nand/raw/ingenic/ingenic_nand_drv.c:330:1-9: WARNING: Use devm_platform_ioremap_resource for cs -> base
Use devm_platform_ioremap_resource helper which wraps
platform_get_resource() and devm_ioremap_resource() together.
Generated by: scripts/coccinelle/api/devm_platform_ioremap_resource.cocci
Fixes: c403ec33b6 ("mtd: rawnand: ingenic: Fix ingenic_ecc dependency")
CC: Paul Cercueil <paul@crapouillou.net>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
- Fix Micron driver as some chips enable internal ECC correction
during their discovery while they advertize they do not have any.
Hyperbus:
- Restrict the build to only ARM64 SoCs (and compile testing) which is
what should have been done since the beginning.
- Fix Kconfig issue by selection something instead of implying it.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl1E0XAACgkQJWrqGEe9
VoSVXAf/XyLI00EIj3L2KF8K8iYLPRN+lfbeN/YrFvFd9WYhyjY82NKQ/7A1WVjB
k5VIJx4StnhvVBFj/amviK4NycZcJ8GXz5eQvd5oQYRP5pZ9rBBeed/7QAdQ1uEJ
s8yZyFZKQblFyqTISDsfAmiRmwPipAn5TrBRPvpN094tSxoz8MB4SLvRsUy4FIrr
zj6wGrIbSu2x/G3KUw7yTDAfL9QOdgHaCnmM04TOndoDPC+38yVs8ca/67AP44Ni
j0cYivMZhVpavx2n3G01WUiyXAgkDilaG3F+Tn6754zxfQhJM5tVzZOiwSCBI9FS
Cg2dgcRXfPlJJuD5Vs7aPFIGJHLEFg==
=TWEV
-----END PGP SIGNATURE-----
Merge tag 'mtd/fixes-for-5.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD fixes from Miquel Raynal:
"NAND:
- Fix Micron driver as some chips enable internal ECC correction
during their discovery while they advertize they do not have any.
Hyperbus:
- Restrict the build to only ARM64 SoCs (and compile testing) which
is what should have been done since the beginning.
- Fix Kconfig issue by selection something instead of implying it"
* tag 'mtd/fixes-for-5.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: hyperbus: Add hardware dependency to AM654 driver
mtd: hyperbus: Kconfig: Fix HBMC_AM654 dependencies
mtd: rawnand: micron: handle on-die "ECC-off" devices correctly
Some devices are not supposed to support on-die ECC but experience
shows that internal ECC machinery can actually be enabled through the
"SET FEATURE (EFh)" command, even if a read of the "READ ID Parameter
Tables" returns that it is not.
Currently, the driver checks the "READ ID Parameter" field directly
after having enabled the feature. If the check fails it returns
immediately but leaves the ECC on. When using buggy chips like
MT29F2G08ABAGA and MT29F2G08ABBGA, all future read/program cycles will
go through the on-die ECC, confusing the host controller which is
supposed to be the one handling correction.
To address this in a common way we need to turn off the on-die ECC
directly after reading the "READ ID Parameter" and before checking the
"ECC status".
Cc: stable@vger.kernel.org
Fixes: dbc44edbf8 ("mtd: rawnand: micron: Fix on-die ECC detection logic")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It has been replaced with the newer Ingenic NAND driver.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This patch fixes the following warning:
drivers/mtd/nand/onenand/onenand_base.c: In function ‘onenand_check_features’:
drivers/mtd/nand/onenand/onenand_base.c:3264:17: warning: this statement may fall through [-Wimplicit-fallthrough=]
this->options |= ONENAND_HAS_NOP_1;
drivers/mtd/nand/onenand/onenand_base.c:3265:2: note: here
case ONENAND_DEVICE_DENSITY_4Gb:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Cc: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a goto from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put under a new goto to put
the node at a loop exit.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a goto from the middle of the loop, there is no
put, thus causing a memory leak. Hence add an of_node_put before the
goto.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This patch solves warnings detected by setting W=1 when building.
Warnings type detected:
drivers/mtd/nand/raw/stm32_fmc2_nand.c: In function ‘stm32_fmc2_calc_timings’:
drivers/mtd/nand/raw/stm32_fmc2_nand.c:1417:23: warning: comparison is
always false due to limited range of data type [-Wtype-limits]
else if (tims->twait > FMC2_PMEM_PATT_TIMING_MASK)
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Cc: stable@vger.kernel.org
Fixes: 2cd457f328 ("mtd: rawnand: stm32_fmc2: add STM32 FMC2 NAND flash controller driver")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
While I was tempted to move it to admin-guide, as some docs
there are more userspace-faced, there are some very technical
discussions about memory error correction code from the Kernel
implementer's PoV. So, let's place it inside the driver-api
book.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rename the mtd documentation files to ReST, add an
index for them and adjust in order to produce a nice html
output via the Sphinx build system.
It should be noticed that Sphinx doesn't handle very well
URLs with dots in the middle. Thankfully, internally, the '.'
char is translated to %2E, so we can jus use %2E instead of
dots, and this will work fine on both text and processed files.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
MTD core changes:
- New Hyperbus framework
- New _is_locked (concat) implementation
- Various cleanups
NAND core changes:
- use longest matching pattern in ->exec_op() default parser
- export NAND operation tracer
- add flag to indicate panic_write in MTD
- use kzalloc() instead of kmalloc() and memset()
Raw NAND controller drivers changes:
- brcmnand:
* fix BCH ECC layout for large page NAND parts
* fallback to detected ecc-strength, ecc-step-size
* when oops in progress use pio and interrupt polling
* code refactor code to introduce helper functions
* add support for v7.3 controller
- FSMC:
* use nand_op_trace for operation tracing
- GPMI:
* move all driver code into single file
* various cleanups (including dmaengine changes)
* use runtime PM to manage clocks
* implement exec_op
- MTK:
* correct low level time calculation of r/w cycle
* improve data sampling timing for read cycle
* add validity check for CE# pin setting
* fix wrongly assigned OOB buffer pointer issue
* re-license MTK NAND driver as Dual MIT/GPL
- STM32:
* manage the get_irq error case
* increase DMA completion timeouts
Raw NAND chips drivers changes:
- Macronix: add read-retry support
Onenand driver changes:
- add support for 8Gb datasize chips
- avoid fall-through warnings
SPI-NAND changes:
- define macros for page-read ops with three-byte addresses
- add support for two-byte device IDs and then for GigaDevice
GD5F1GQ4UFxxG
- add initial support for Paragon PN26G0xA
- handle the case where the last page read has bitflips
SPI-NOR core changes:
- add support for the mt25ql02g and w25q16jv flashes
- print error in case of jedec read id fails
- is25lp256: add post BFPT fix to correct the addr_width
SPI NOR controller drivers changes:
- intel-spi: Add support for Intel Elkhart Lake SPI serial flash
- smt32: remove the driver as the driver was replaced by spi-stm32-qspi.c
- cadence-quadspi: add reset control
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl0qLr4ACgkQJWrqGEe9
VoQVCwf/ZCG5CldS3cs6B68kMJoZ/rJyJxBnxtIhffda2vw1KG/12o6XaDO9xA/R
EwYrOTzlYZxzCZsNvWyHepG3Kj3d38CJ52ZqhavjpihwMlKKOgW/K39xuKWCrfxS
sVMLz/UdrcsQfcPGAy7DSyqhzRAtupNxngCdEkIIMGFZWsv4uZfOFEGMrzUJ5RYN
/okIyUE7Iz0dRq1/KXSl365V1MS8QP2eHFuHrUd38+kJ8TJnQjXX3Bmdul4aNTx+
HIIpykovoAn5BZ0YA4lJL90zVoDOWysARwHIAMDvJa8zS0wDTU16Tj2M6AQK+a4x
hbIOOkeX0hTKpJvy7/khli5y1bn2mw==
=L+tV
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"This contains the following changes for MTD:
MTD core changes:
- New Hyperbus framework
- New _is_locked (concat) implementation
- Various cleanups
NAND core changes:
- use longest matching pattern in ->exec_op() default parser
- export NAND operation tracer
- add flag to indicate panic_write in MTD
- use kzalloc() instead of kmalloc() and memset()
Raw NAND controller drivers changes:
- brcmnand:
- fix BCH ECC layout for large page NAND parts
- fallback to detected ecc-strength, ecc-step-size
- when oops in progress use pio and interrupt polling
- code refactor code to introduce helper functions
- add support for v7.3 controller
- FSMC:
- use nand_op_trace for operation tracing
- GPMI:
- move all driver code into single file
- various cleanups (including dmaengine changes)
- use runtime PM to manage clocks
- implement exec_op
- MTK:
- correct low level time calculation of r/w cycle
- improve data sampling timing for read cycle
- add validity check for CE# pin setting
- fix wrongly assigned OOB buffer pointer issue
- re-license MTK NAND driver as Dual MIT/GPL
- STM32:
- manage the get_irq error case
- increase DMA completion timeouts
Raw NAND chips drivers changes:
- Macronix: add read-retry support
Onenand driver changes:
- add support for 8Gb datasize chips
- avoid fall-through warnings
SPI-NAND changes:
- define macros for page-read ops with three-byte addresses
- add support for two-byte device IDs and then for GigaDevice
GD5F1GQ4UFxxG
- add initial support for Paragon PN26G0xA
- handle the case where the last page read has bitflips
SPI-NOR core changes:
- add support for the mt25ql02g and w25q16jv flashes
- print error in case of jedec read id fails
- is25lp256: add post BFPT fix to correct the addr_width
SPI NOR controller drivers changes:
- intel-spi: Add support for Intel Elkhart Lake SPI serial flash
- smt32: remove the driver as the driver was replaced by spi-stm32-qspi.c
- cadence-quadspi: add reset control"
* tag 'mtd/for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (60 commits)
mtd: concat: implement _is_locked mtd operation
mtd: concat: refactor concat_lock/concat_unlock
mtd: abi: do not use C++ style comments in uapi header
mtd: afs: remove unneeded NULL check
mtd: rawnand: stm32_fmc2: increase DMA completion timeouts
mtd: rawnand: Use kzalloc() instead of kmalloc() and memset()
mtd: hyperbus: Add driver for TI's HyperBus memory controller
mtd: spinand: read returns badly if the last page has bitflips
mtd: spinand: Add initial support for Paragon PN26G0xA
mtd: rawnand: mtk: Re-license MTK NAND driver as Dual MIT/GPL
mtd: rawnand: gpmi: remove double assignment to block_size
dt-bindings: mtd: brcmnand: Add brcmnand, brcmnand-v7.3 support
mtd: rawnand: brcmnand: Add support for v7.3 controller
mtd: rawnand: brcmnand: Refactored code to introduce helper functions
mtd: rawnand: brcmnand: When oops in progress use pio and interrupt polling
mtd: Add flag to indicate panic_write
mtd: rawnand: Add Macronix NAND read retry support
mtd: onenand: Avoid fall-through warnings
mtd: spinand: Add support for GigaDevice GD5F1GQ4UFxxG
mtd: spinand: Add support for two-byte device IDs
...
Allwinner NAND controllers can make use of DMA to enhance the I/O
throughput thanks to ECC pipelining. DMA handling with A23/A33 NAND IP
is a bit different than with the older SoCs, hence the introduction of
a new compatible to handle:
* the differences between register offsets,
* the burst length change from 4 to minimum 8,
* manage SRAM accesses through MBUS with extra configuration.
Fixes: c49836f05a ("mtd: rawnand: sunxi: Add A23/A33 DMA support")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This reverts commit c49836f05a.
The commit is wrong and its approach actually does not work. Let's
revert it in order to add the feature with a clean patch.
Fixes: c49836f05a ("mtd: rawnand: sunxi: Add A23/A33 DMA support")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
If MTD_NAND_JZ4780 is y and MTD_NAND_JZ4780_BCH is m,
which select CONFIG_MTD_NAND_INGENIC_ECC to m, building fails:
drivers/mtd/nand/raw/ingenic/ingenic_nand.o: In function `ingenic_nand_remove':
ingenic_nand.c:(.text+0x177): undefined reference to `ingenic_ecc_release'
drivers/mtd/nand/raw/ingenic/ingenic_nand.o: In function `ingenic_nand_ecc_correct':
ingenic_nand.c:(.text+0x2ee): undefined reference to `ingenic_ecc_correct'
To fix that, the ingenic_nand and ingenic_ecc modules have been fused
into one single module.
- The ingenic_ecc.c code is now compiled in only if
$(CONFIG_MTD_NAND_INGENIC_ECC) is set. This is now a boolean instead
of tristate.
- To avoid changing the module name, the ingenic_nand.c file is moved to
ingenic_nand_drv.c. Then the module name is still ingenic_nand.
- Since ingenic_ecc.c is no more a module, the module-specific macros
have been dropped, and the functions are no more exported for use by
the ingenic_nand driver.
Fixes: 15de8c6efd ("mtd: rawnand: ingenic: Separate top-level and SoC specific code")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Hulk Robot <hulkci@huawei.com>
Cc: YueHaibing <yuehaibing@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The 1Gb Macronix chip can have a maximum of 20 bad blocks, while
the 2Gb version has twice as many blocks and therefore the maximum
number of bad blocks is 40.
The 4Gb GigaDevice GD5F4GQ4xA has twice as many blocks as its 2Gb
counterpart and therefore a maximum of 80 bad blocks.
Fixes: 377e517b5f ("mtd: nand: Add max_bad_eraseblocks_per_lun info to memorg")
Reported-by: Emil Lenngren <emil.lenngren@gmail.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
When the system is overloaded, DMA data transfer completion occurs after
100ms. Increase the timeouts to let it the time to complete.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
