Print the enable_mask and status_mask from
__i915_{enable,disable}_pipestat() when the caller has messed them up
somehow.
v2: Use pipe_name() (Damien)
Fix a typo in the commit message
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In commit a51435a313
Author: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Date: Wed Mar 12 16:39:40 2014 +0530
drm/i915: disable rings before HW status page setup
we reordered stopping the rings to do so before we set the HWS register.
However, there is an extra workaround for g45 to reset the rings twice,
and for consistency we should apply that workaround before setting the
HWS to be sure that the rings are truly stopped.
Cc: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have been setting the bit which was originally BIOS dependent since:
commit f05bb0c7b6
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Sun Jan 20 16:33:32 2013 +0000
drm/i915: GFX_MODE Flush TLB Invalidate Mode must be '1' for scanline waits
Therefore, we do not need to try to figure it out dynamically and we can
just always invalidate the TLBs.
It's a partial revert of:
commit 12b0286f49
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Mon Jun 4 14:42:50 2012 -0700
drm/i915: possibly invalidate TLB before context switch
The original commit attempted to only invalidate when necessary
(very much a relic from the old days). Now, we can just always invalidate.
I guess the old TODO still exists. Since we seem to have abandoned ILK
contexts however, there isn't much point in even remembering.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The framecount register was still using the old PIPE macro instead
of the new PIPE2 macro
Signed-off-by: Rafael Barbalho <rafael.barbalho@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DPIO reads from groups/broadcast register offsets for PCS and
TX return all 1's. If that result gets used for something
we'll probably end up doing something wrong. So warn when that
happens.
FIXME there might be some registers where all 1's is a valid value,
so ideally we should check the register offset instead...
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: copypaste the FIXME comment into the code.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's no point in hiding the DP M/N setup in the update_pll functions.
Just move it to the mode_set function.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Iterate over all the PDP registers instead of just printing PDP0 four
times in gen8 PPGTT debugfs info.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Our validation guys want to have a positive proof that the gfx driver
is indeed using VT-d, since setting up a gfx stack, especially in
early bring-up and by people not versed in linux gfx is a bit tricky.
So provide just that.
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VTd has a few too many "outright disable the damn thing" workarounds
accumulated and for validation we want a simple knob to make sure we
disable them all.
Since this is for bdw+ validation and atm we don't have any
workarounds for bdw this option currently does nothing. So currently
this is just a placeholder to make sure reality will match with the
documented process for our validation people.
v2: Fix up param description (Jani).
v3: Actually git add ...
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If I boot my Broadwell machine to X on a system with Mesa Gallium
llvmpipe instead of i965, then kill X and try to run pm_pc8.c, when we
disable PC8 and call gen6_update_ring_freq(), we will get stuck on an
infinite loop because the frequencies are zero and the variables are
unsigned. This happens because we never ran any batch, so we did not
enable RC6, so the variables are zero. If I run gem_exec_nop before
running pm_pc8, everything works as expected because gem_exec_nop
makes RC6 be enabled.
This commit should prevent the infinite loop, which IMHO is already a
good reason to be merged, but it is not the proper fix to the "RC6 is
not being enabled" problem.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because if we keep the current code, we'll get tons of WARNs on
Broadwell, since the code is Haswell-specific.
We could have also added a Broadwell-specific code there, but it's not
really needed since we never disable LCPLL with the hotplug interrupts
still enabled. So keep the easy-and-simple-to-maintain solution until
we actually need something else.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch Enables the bit for TLB invalidate in GFX Mode register
for Gen7.
According to bspec, When enabled this bit limits the invalidation
of the TLB only to batch buffer boundaries, to pipe_control
commands which have the TLB invalidation bit set and sync flushes.
If disabled, the TLB caches are flushed for every full flush of
the pipeline.
Tested only on vlv platform. Chris has tested on ivb and hsw
platforms.
v2: Adding the explicit enabling of this bit for all Gen7 platforms
instead of only vlv (Chris)
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Sourab Gupta <sourab.gupta@intel.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk> #ivb, hsw -Chris
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add w/a markers as suggested by Ville.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Drop the cast from the pointer diff to fix:
drivers/gpu/drm/i915/i915_cmd_parser.c:405:4: warning: format '%td' expects
argument of type 'ptrdiff_t', but argument 5 has type 'long unsigned int'
[-Wformat]
While at it, use %u for u32.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
[danvet: After conflict resolution only the "While at it, ..." part
was left standing ...]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is some thought that the data from the performance counters enabled
via OACONTROL should only be available to the process that enabled counting.
To limit snooping, require that any batch buffer which sets OACONTROL to a
non-zero value also sets it back to 0 before the end of the batch.
This requires limiting OACONTROL writes to happen via MI_LOAD_REGISTER_IMM
so that we can access the value being written. This should be in line with
the expected use case for writing OACONTROL.
v2: Drop an unnecessary '? true : false'
Cc: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This brings the code a little more in line with kernel coding style.
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As suggested during review, this makes it much more obvious
when the tables are not sorted.
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For error state, like the recent modification to ACTHD, FADD also gets
an upper dword. This is useful for debug to make sure the fetch address
and head are similar.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BSpec seems to tell us we need the MI_ARB_ON_OFF w/a around
MI_SET_CONTEXT on gen8.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This sould be enough.
v2: BDW should also run hsw_runtime_resume (Ben).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
That's what the spec said! And HSW needs it through pcode (you can
only read it through MCHBAR), so create hsw_write_dcomp to abstract
the weirdness.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that PC8 is part of runtime PM, the check is useless.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just because I have a SNB machine and I can easily test it.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We're adding runtime suspend support to more platforms, so organize
the code in a way that all a new platform needs to do is to add its
own gen-specific functions. Also rename the i915_ functions to intel_
to make it clear that it's the top level one, not something that just
runs on i915 platforms.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we don't keep the hotplug interrupts enabled anymore, we can
kill the regsave struct and just cal the normal IRQ preinstall,
postinstall and uninstall functions. This makes it easier to add
runtime PM support to non-HSW platforms.
The only downside is in case we get a request to update interrupts
while they are disabled, won't be able to update the regsave struct.
But this should never happen anyway, so we're not losing too much.
v2: - Rebase.
v3: - Rebase.
v4: - Rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We should only enable interrupts at postinstall.
And now on ILK/SNB/IVB/HSW the irq_preinstall and irq_postinstall
functions leave the hardware in the same state.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fix compile fail due to drm_i915_private_t typedef removal.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So we can merge all the common code from postinstall and uninstall.
v2: - Rebase.
- While at it, remove useless { and }.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To merge the common code of ironlake_irq_preinstall and
ironlake_irq_uninstall.
We should also probably do something about that HSWSTAM write on a
later commit.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fix compile fail due to drm_i915_private_t typedef removal.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Missing from gen8_irq_uninstall.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After the latest changes, ibx_irq_preinstall and ibx_irq_uninstall are
the same, so remove one of the copies and rename the other to
ibx_irq_reset (since we're using the "reset" name for things which are
called both at preinstall and uninstall).
v2: - Rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On the preinstall stage we should just disable all the interrupts, but
we currently enable all the south display interrupts due to the way we
touch SDEIER at the IRQ handlers (note: they are still masked and our
IRQ handler is disabled). Instead of doing that, let's make the
preinstall stage just disable all the south interrupts, and do the
proper interrupt dance/ordering at the postinstall stage, including an
assert to check if everything is behaving as expected.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After all, we call ibx_irq_preinstall from gen8_irq_preinstall.
v2: - Rebase.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like ibx_irq_preinstall. We'll call this from somewhere else in
the next patch.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The duplicate was at an _uninstall function, so rename it to
gen5_gt_irq_reset.
v2: - Rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Same as SERR_INT and the other IIR registers: reset on
preinstall/uninstall and WARN for non-zero values at postinstall. This
one also doesn't need double-clear.
v2: - Remove the is_zero assertion (Ben).
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The SERR_INT register is very similar to the other IIR registers, so
let's zero it at preinstall/uninstall and WARN for a non-zero value at
postinstall, just like we do with the other IIR registers. For this
one, there's no need to double-clear since it can't store more than
one interrupt.
v2: - Remove the is_zero assertion (Ben).
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It should already be masked and disabled and zeroed at the preinstall
and uninstall stages. Also, the current code just writes to IIR once,
and this is not a guarantee that it will be cleared, so it's wrong
anyway.
The whole reason for the paranoia is that we're going to start calling
the IRQ preinstall/postinstall/uninstall from the runtime PM
callbacks, so we need to make sure everything is behaving as expected.
v2: - Change the original DRM_ERROR to WARN and clear IIR in case it's
not zero (Ben).
- Improve commit message (Daniel).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And the equivalent GEN8_IRQ_INIT_NDX macro. These macros are for the
postinstall functions. The next patch will improve this macro.
v2: - Adjust to the new POSTING_READ scheme (Ben).
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The IRQ_INIT and IRQ_FINI macros are basically the same thing, with
the exception that IRQ_FINI doesn't properly clear IIR twice and
doesn't have as many POSTING_READs as IRQ_INIT. So rename the INIT
macro to IRQ_RESET and use it everywhere.
v2: - Fix error in the commit message (Chris).
- Adjust to the new POSTING_READ scheme (Ben).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's the only thing missing, apparently.
v2: - Fix typo (Ben).
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Same as the _INIT macro: the goal is to reuse the GEN8 macros, but
there are still some slight differences.
v2: - Rebase.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And rename it to GEN5_IRQ_INIT.
We have discussed doing equivalent changes on July 2013, and I even
sent a patch series for this: "[PATCH 00/15] Unify interrupt register
init/reset". Now that the BDW code was merged, I have one more
argument in favor of these changes.
Here's what really changes with the Gen 5 IRQ init code:
- We now clear the IIR registers at preinstall (they are also
cleared at postinstall, but we will change that later).
- We have an additional POSTING_READ at the IMR register.
v2: - Fix typo in commit message.
- Add POSTING_READ calls to the macros (Ben, Daniel, Jani).
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This interrupt gets initialized with a different IER value, so it was
not using the macro. The problem is that we plan to modify the macro
to make it do additional things, and we want the SDE interrupts
updated too. So let's make sure we call the macro, then, after it, we
do the necessary SDE-specific changes.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The goal is to reuse the GEN8 macros, but a few changes are needed, so
let's make things easier to review.
I could also use these macros on older code, but since I plan to
change how the interrupts are initialized, we'll risk breaking the
older code in the next commits, so I'll leave this out for now.
v2: - Rebase.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch reads the DRRS support and Mode type from VBT fields.
The read information will be stored in VBT struct during BIOS
parsing. The above functionality is needed for decision making
whether DRRS feature is supported in i915 driver for eDP panels.
This information helps us decide if seamless DRRS can be done
at runtime to support certain power saving features. This patch
was tested by setting necessary bit in VBT struct and merging
the new VBT with system BIOS so that we can read the value.
v2: Incorporated review comments from Chris Wilson
Removed "intel_" as a prefix for DRRS specific declarations.
v3: Incorporated Jani's review comments
Removed function which deducts drrs mode from panel_type. Modified some
print statements. Made changes to use DRRS_NOT_SUPPORTED as 0 instead of -1.
v4: Incorporated Jani's review comments.
Modifications around setting vbt drrs_type.
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
[danvet: Drop the misleading/redundant comment about the added drrs
field in the vbt struct as discussed with Jani on irc.]
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently drm_cflush_virt_rage() takes a char* so the caller probably
has to do pointless casting to avoid compiler warnings. Make the
argument void* instead to avoid such issues.
v2: Use void* arithmetic (Chris)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull all the gmch platform hotplug interrupt handling into one
function.
v2: Move the IIR check to the caller
s/drm_i915_private_t/struct drm_i915_private/
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add posting read comment suggested by Chris.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have a need for duplicated parsing of the RP_STATE_CAPS register (and
the setting of the associated fields). To reuse some code, we can
extract the function into a simple helper.
This patch also addresses the fact that we missed doing this for gen8,
something we should have done anyway.
This could be two patches, one to extract, and one to add gen8, but it's
trivial enough that I think one is fine. I will accept a request to
split it. Please notice the fix addressed by v2 below.
Valleyview is left untouched because it is different.
v2: Logically rebased on top of
commit dd0a1aa19b
Author: Jeff McGee <jeff.mcgee@intel.com>
Date: Tue Feb 4 11:32:31 2014 -0600
drm/i915: Restore rps/rc6 on reset
Note with the above change the fix for gen8 is also handled (which was
not the case in Jeff's original patch).
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Programming it outside of the rp0-rp1 range is considered a programming
error. Since we do not know that the previous value would actually be in
the range, program something we've read from the hardware, and therefore
know will work.
This is potentially an issue for platforms whose ranges are outside the
norms given in the programming guide (ie. early silicon)
v2: Use RP1 instead of RPn
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
