Compare with LCLK mode, PG mode saves more power, by turning
off more circuits. Therefore, to recover from PG mode, driver
needs to backup some information into rsvd page. Such as CAM
entries, DPK results.
As CAM entries can change, it is required to re-download CAM
entries after set_key.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add a module parameter to select deep PS mode. And the mode
cannot be changed after the module has been inserted and probed.
If anyone wants to change the deep mode, should change the mode
and probe the device again to setup the changed deep mode.
When the device is probed, driver will check the deep PS mode
with different IC's PS mode suppotability. If none of the
PS mode is matched, the deep PS mode is changed to NONE,
means deep PS is disabled.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sometimes LPS is not compatible with COEX's strategy, and
COEX will not allow driver to enter it.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Deep power save allows firmware/hardware to operate in a
lower power state. And the deep power save mode depends on
LPS mode. So, before entering deep PS, driver must first
enter LPS mode.
Under Deep PS, most of hardware functions are shutdown,
driver will not be able to read/write registers and transfer
data to the device. Hence TX path must be protected by each
interface. Take PCI for example, DMA engine should be idle,
and no nore activities on the PCI bus.
If driver wants to operate on the device, such as register
read/write, it must first acquire the mutex lock and wake
up from Deep PS, otherwise the behavior is undefined.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Dynamic mechanism requires BB/RF working to adjust
hardware settings. But PS state periodically turns
off BB/RF, could lead to wrong setting.
So leave PS state before DM to make sure it works.
And then check if we can enter PS state again.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Protect LPS enter/leave routine with rtwdev->mutex.
This helps to synchronize with driver's states correctly.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The original design of LPS enter/leave routines allows
to control the LPS state by each interface. But the
hardware cannot actually handle it that way. This means
the hardware can only enter LPS once with an associated
port, so there is no need to keep tracking the state of
each vif.
Hence the logic of enter/leave LPS state can be simple,
just to check the state of the device's flag. And for
leaving LPS state, it will get the same port id to send
to inform the hardware.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove PS related *_irqsafe functions to avoid entering/leaving PS
under interrupt context. Instead, make PS decision in watch_dog.
This could simplify the logic and make the code look clean.
But it could have a little side-effect that if the driver is having
heavy traffic before the every-2-second watch_dog detect the traffic
and decide to leave PS, the thoughput will be lower. Once traffic is
detected by watch_dog and left PS state, the throughput will resume
to the peak the hardware ought to have again.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If the driver doesn't reset the host's and device's indexes
in a single write, the indexes will become different in a
short period. And it will confuse the DMA engine, make it
start to process non-existed entries.
Better to Write-1-to-reset the indexes, for the DMA engine
to know that this is a reset of the H2C queue, not a kick
off.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These helper functions seems useless. And in some cases
we want to use test_and_[set/clear]_bit, these helpers
will make the code more complicated. So remove them.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8723be/phy.c: In function rtl8723be_phy_iq_calibrate:
drivers/net/wireless/realtek/rtlwifi/rtl8723be/phy.c:2255:7: warning: variable reg_ecc set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/rtl8723be/phy.c: In function rtl8723be_phy_iq_calibrate:
drivers/net/wireless/realtek/rtlwifi/rtl8723be/phy.c:2254:34: warning: variable reg_eac set but not used [-Wunused-but-set-variable]
They are not used since commit a619d1abe2 ("rtlwifi:
rtl8723be: Add new driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/phy.c: In function rtl92ee_phy_iq_calibrate:
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/phy.c:2805:34: warning: variable reg_ecc set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/phy.c: In function rtl92ee_phy_iq_calibrate:
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/phy.c:2804:34: warning: variable reg_eac set but not used [-Wunused-but-set-variable]
They are not used since commit b1a3bfc97c ("rtlwifi:
rtl8192ee: Move driver from staging to the regular tree")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/trx.c: In function rtl92ee_tx_fill_desc:
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/trx.c:656:5: warning: variable short_gi set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/trx.c: In function rtl92ee_tx_fill_desc:
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/trx.c:648:15: warning: variable buf_len set but not used [-Wunused-but-set-variable]
They are not used since commit f1d2b4d338 ("rtlwifi:
rtl818x: Move drivers into new realtek directory")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/efuse.c: In function efuse_pg_packet_write:
drivers/net/wireless/realtek/rtlwifi/efuse.c:937:24: warning: variable dataempty set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/efuse.c: In function efuse_get_current_size:
drivers/net/wireless/realtek/rtlwifi/efuse.c:1202:5: warning: variable hoffset set but not used [-Wunused-but-set-variable]
They are not used since commit f1d2b4d338 ("rtlwifi:
rtl818x: Move drivers into new realtek directory")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/ps.c: In function rtl_ps_set_rf_state:
drivers/net/wireless/realtek/rtlwifi/ps.c:71:19: warning: variable rtstate set but not used [-Wunused-but-set-variable]
It is not used since commit f1d2b4d338 ("rtlwifi:
rtl818x: Move drivers into new realtek directory")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In rtl8xxxu_submit_int_urb if usb_submit_urb fails the allocated urb
should be released.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
kmemdup is introduced to duplicate a region of memory in a neat way.
Rather than kmalloc/kzalloc + memcpy, which the programmer needs to
write the size twice (sometimes lead to mistakes), kmemdup improves
readability, leads to smaller code and also reduce the chances of mistakes.
Suggestion to use kmemdup rather than using kmalloc/kzalloc + memcpy.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is clearer than copy/pasting the magic number '+ 2' around, and it
even saves the need for one existing comment.
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
alloc_workqueue is not checked for errors and as a result,
a potential NULL dereference could occur.
Signed-off-by: Allen Pais <allen.pais@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is no need to check "rtlhal->interface == INTF_PCI" twice in
_rtl_ps_inactive_ps(). The nested check is always true. Thus, the
expression can be simplified.
Signed-off-by: Denis Efremov <efremov@linux.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In rtl_usb_probe if allocation for usb_data fails the allocated hw
should be released. In addition the allocated rtlpriv->usb_data should
be released on error handling path.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
'rtstatus' local variable is not used,
so remove it for clean-up.
Signed-off-by: Austin Kim <austindh.kim@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix bbp ready check in mt7601u_wait_bbp_ready. The issue is reported by
coverity with the following error:
Logical vs. bitwise operator
The expression's value does not depend on the operands; inadvertent use
of the wrong operator is a likely logic error.
Addresses-Coverity-ID: 1309441 ("Logical vs. bitwise operator")
Fixes: c869f77d6a ("add mt7601u driver")
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In rsi_send_beacon, if rsi_prepare_beacon fails the allocated skb should
be released.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
drivers/net/wireless/realtek/rtw88/rtw8822c.c:2606:9-10: WARNING: return
of 0/1 in function 'rtw8822c_dpk_coef_iq_check' with return type bool
Return statements in functions returning bool should use true/false
instead of 1/0.
Generated by: scripts/coccinelle/misc/boolreturn.cocci
Fixes: 5227c2ee45 ("rtw88: 8822c: add SW DPK support")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The nested 'li_mimo == &locale_bn' check is excessive and always
true. Thus it can be safely removed.
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
brcmfmac assumed the wifi device always remains powered on and thus
hardcoded the MMC_PM_KEEP_POWER flag expecting the wifi device to
remain on even during suspend/resume cycles.
This is not always the case, some appliances cut power to everything
connected via SDIO for efficiency reasons and this leads to wifi not
being usable after coming out of suspend because the device was not
correctly reinitialized.
So we check for the keep_power capability and if it's not present then
we remove the device and probe it again during resume to mirror what's
happening in hardware and ensure correct reinitialization in the case
when MMC_PM_KEEP_POWER is not supported.
Suggested-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Signed-off-by: Adrian Ratiu <adrian.ratiu@collabora.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When n_reqs == 0 there is nothing to do so it doesn't make sense to
search for requests and issue a warning because none is found.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Signed-off-by: Adrian Ratiu <adrian.ratiu@collabora.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
'pih' is known to be non-NULL at this point, so the test can be removed.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With FT-802.1X, driver should send a port authorized event right after
sending a roamed event. It is used to indicate that a new AP is already
authorized so 802.1X is not required.
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pull networking fixes from David Miller:
1) Sanity check URB networking device parameters to avoid divide by
zero, from Oliver Neukum.
2) Disable global multicast filter in NCSI, otherwise LLDP and IPV6
don't work properly. Longer term this needs a better fix tho. From
Vijay Khemka.
3) Small fixes to selftests (use ping when ping6 is not present, etc.)
from David Ahern.
4) Bring back rt_uses_gateway member of struct rtable, it's semantics
were not well understood and trying to remove it broke things. From
David Ahern.
5) Move usbnet snaity checking, ignore endpoints with invalid
wMaxPacketSize. From Bjørn Mork.
6) Missing Kconfig deps for sja1105 driver, from Mao Wenan.
7) Various small fixes to the mlx5 DR steering code, from Alaa Hleihel,
Alex Vesker, and Yevgeny Kliteynik
8) Missing CAP_NET_RAW checks in various places, from Ori Nimron.
9) Fix crash when removing sch_cbs entry while offloading is enabled,
from Vinicius Costa Gomes.
10) Signedness bug fixes, generally in looking at the result given by
of_get_phy_mode() and friends. From Dan Crapenter.
11) Disable preemption around BPF_PROG_RUN() calls, from Eric Dumazet.
12) Don't create VRF ipv6 rules if ipv6 is disabled, from David Ahern.
13) Fix quantization code in tcp_bbr, from Kevin Yang.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (127 commits)
net: tap: clean up an indentation issue
nfp: abm: fix memory leak in nfp_abm_u32_knode_replace
tcp: better handle TCP_USER_TIMEOUT in SYN_SENT state
sk_buff: drop all skb extensions on free and skb scrubbing
tcp_bbr: fix quantization code to not raise cwnd if not probing bandwidth
mlxsw: spectrum_flower: Fail in case user specifies multiple mirror actions
Documentation: Clarify trap's description
mlxsw: spectrum: Clear VLAN filters during port initialization
net: ena: clean up indentation issue
NFC: st95hf: clean up indentation issue
net: phy: micrel: add Asym Pause workaround for KSZ9021
net: socionext: ave: Avoid using netdev_err() before calling register_netdev()
ptp: correctly disable flags on old ioctls
lib: dimlib: fix help text typos
net: dsa: microchip: Always set regmap stride to 1
nfp: flower: fix memory leak in nfp_flower_spawn_vnic_reprs
nfp: flower: prevent memory leak in nfp_flower_spawn_phy_reprs
net/sched: Set default of CONFIG_NET_TC_SKB_EXT to N
vrf: Do not attempt to create IPv6 mcast rule if IPv6 is disabled
net: sched: sch_sfb: don't call qdisc_put() while holding tree lock
...
First set of fixes for 5.4 sent during the merge window. Most are
regressions fixes but the mt7615 problem has been since it was merged.
iwlwifi
* fix a build regression related CONFIG_THERMAL
* avoid using GEO_TX_POWER_LIMIT command on certain firmware versions
rtw88
* fixes for skb leaks
zd1211rw
* fix a compiler warning on 32 bit
mt76
* fix the firmware paths for mt7615 to match with linux-firmware
wil6210
* fix use of skb after free
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdjLN3AAoJEG4XJFUm622bsBcH/1A/srmEN3bME86p9j0DS1Wb
A/8KPP88q9gczIDg+uZQCw1rTqHUrqkgbPxVCa64tKdPjqioRc9nW4CVhKh2OLTy
88Bwh/mJhxfh/+TTfYf397OsHr9NEVaFnEqjYeUxtyhRoZriUmAtKSd4/689czDP
AOdbkXShe8pUS+UvpizfpOHP28j4TbFOzcWn8qcGm1gqfuCHan+giaSw073vz+r4
fagOz470huyqCwx8LB21IzTCunox20W4IfN/G2AMoKx7tE9XbYr6kRR8vawffwm2
FVyhlnibkRQnRv77thg+zJZQ6UpJybsfM8Izpn1kTDFiRChNqvMtOKboz+IQOHg=
=4i7U
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2019-09-26' of https://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 5.4
First set of fixes for 5.4 sent during the merge window. Most are
regressions fixes but the mt7615 problem has been since it was merged.
iwlwifi
* fix a build regression related CONFIG_THERMAL
* avoid using GEO_TX_POWER_LIMIT command on certain firmware versions
rtw88
* fixes for skb leaks
zd1211rw
* fix a compiler warning on 32 bit
mt76
* fix the firmware paths for mt7615 to match with linux-firmware
wil6210
* fix use of skb after free
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The debug code dereferences "skb" to print "skb->len" so we have to
print the message before we free "skb".
Fixes: f99fe49ff3 ("wil6210: add wil_netif_rx() helper function")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The intention was to have the GEO_TX_POWER_LIMIT command in FW version
36 as well, but not all 8000 family got this feature enabled. The
8000 family is the only one using version 36, so skip this version
entirely. If we try to send this command to the firmwares that do not
support it, we get a BAD_COMMAND response from the firmware.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=204151.
Cc: stable@vger.kernel.org # 4.19+
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mt7615 patch/n9/cr4 firmwares are available in mediatek folder in
linux-firmware repository. Because of this mt7615 won't work on regular
distributions like Ubuntu. Fix path definitions. Moreover remove useless
firmware name pointers and use definitions directly
Fixes: 04b8e65922 ("mt76: add mac80211 driver for MT7615 PCIe-based chipsets")
Cc: stable@vger.kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After firmware has been downloaded, driver should send
some information to it through H2C commands. Those H2C
commands are transmitted through TX path.
But before HCI has been started, the TX path is not
working completely. Such as PCI interfaces, the interrupts
are not enabled, hence TX interrupts will not be issued
after H2C skb has been DMAed to the device. And the H2C
skbs will not be released until the device is powered off.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On 32-bit:
drivers/net/wireless/zydas/zd1211rw/zd_usb.c: In function ‘check_read_regs’:
drivers/net/wireless/zydas/zd1211rw/zd_def.h:18:25: warning: format ‘%ld’ expects argument of type ‘long int’, but argument 6 has type ‘size_t’ {aka ‘unsigned int’} [-Wformat=]
dev_printk(level, dev, "%s() " fmt, __func__, ##args)
^~~~~~~
drivers/net/wireless/zydas/zd1211rw/zd_def.h:22:4: note: in expansion of macro ‘dev_printk_f’
dev_printk_f(KERN_DEBUG, dev, fmt, ## args)
^~~~~~~~~~~~
drivers/net/wireless/zydas/zd1211rw/zd_usb.c:1635:3: note: in expansion of macro ‘dev_dbg_f’
dev_dbg_f(zd_usb_dev(usb),
^~~~~~~~~
drivers/net/wireless/zydas/zd1211rw/zd_usb.c:1636:51: note: format string is defined here
"error: actual length %d less than expected %ld\n",
~~^
%d
Fixes: 84b0b66352 ("zd1211rw: zd_usb: Use struct_size() helper")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Interrupt is disabled to stop PCI, which means the skbs
queued for each TX ring will not be released via DMA
interrupt. To avoid those skbs remained being left in
the skb queue until PCI has been removed, driver needs
to release skbs by itself.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These skbs free routines could be used when driver wants
to stop PCI bus, because some of the skbs remained in the
queue may not have been returned via DMA interrupt.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Without CONFIG_THERMAL, the driver fails to link as it calls
iwl_mvm_send_temp_report_ths_cmd() unconditionally. Fix this
by making that function available, but do almost nothing but
send the empty firmware command to enable CT-kill reporting.
While at it, also fix that function itself to not error out
when the thermal zone hasn't been initialized, but instead
just send the empty firmware command in this case as well.
Fixes: 242d9c8b9a ("iwlwifi: mvm: use FW thermal monitoring regardless of CONFIG_THERMAL")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath.git patches for 5.4. Major changes:
wil6210
* add support for Enhanced Directional Multi-Gigabit (EDMG) channels 9-11
* add debugfs file to show PCM ring content
* report boottime_ns in scan results
ath9k
* add a separate loader for AR92XX (and older) pci(e) without eeprom,
enabled with the new ATH9K_PCI_NO_EEPROM Kconfig option
Report chains and chain_signal in ieee80211_rx_status.
It is useful for program such as tcpdump to see if the
antennas are well connected/placed.
8822C is able to receive CCK rates with 2 antennas, while
8822B can only use 1 antenna path to receive CCK rates.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix the wrong RF path for CCK rx power calculation.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92d_evm_db_to_percentage is functionally identical
to the generic version rtl_evm_db_to_percentage, so remove
_rtl92d_evm_db_to_percentage and use the generic version instead.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92c_evm_db_to_percentage is functionally identical
to the generic version rtl_evm_db_to_percentage, so remove
_rtl92c_evm_db_to_percentage and use the generic version instead.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92c_evm_db_to_percentage is functionally identical
to the generic version rtl_evm_db_to_percentage, so remove
_rtl92c_evm_db_to_percentage and use the generic version instead.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
