Through the driver, struct iwl_fw will
store the firmware. Split this out into
a separate file, iwl-fw.h, and make all
other code use it. To do this, also move
the log pointers into it, and remove the
knowledge of "nic" from everything.
Now the op_mode has a fw pointer, and
(unfortunately) for now the shared data
also needs to keep one for the transport
to access dump the error log -- I think
that will move later.
Since I wanted to constify the firmware
pointers, some more changes were needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
uCode loading belongs to the op_mode, as it
is dependent on various things there and the
commands sent during it are specific to it.
Move the prototypes to iwl-agn.h to indicate
this. To make this possible, also move all
the calibration handling (which is op_mode
dependent after all).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This doesn't belong into the op_mode, it has
to be in the drv stop flow instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware request is a base driver flow,
it isn't related to any specific mode.
Move the code related to it into the
base driver file iwl-drv.c.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is used from there, so should be in it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This shouldn't be in the op_mode, as it
will later be switchable at runtime.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My patch "iwlwifi: simplify auth/assoc flow"
caused a serious throughput degradation due
to me forgetting that there are HT settings
in the station table. To restore throughput,
set these parameters correctly when the sta
moves to assoc state.
This patch should probably be merged with
the auth/assoc redesign patch for upstream.
In that case, this paragraph should be added
to the commit log as the third paragraph
(before talking about RXON):
However, as we only get the station HT data
when the station moves into assoc state, we
also need to program this into the device
(and copy it into our database) then.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These are DVM specific, and shouldn't be
in iwl-shared.h.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only used in two places in the same file,
no need to be in iwl-shared.h.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, queue mapping is handled in the
transport. This may change, but until then
the code for it can be close to where it's
used rather than in iwl-shared.h.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is how the transport passes things
up into higher layers, so it belongs to
the transport API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl_queue_inc_wrap/iwl_queue_dec_wrap aren't
shared functions, they are PCI-E specific,
so move them into the appropriate header.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The annotation/documentation is wrong, we call
it in a context that can't sleep.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just make the code easier to read with less indentation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
struct iwl_rx_mem_buffer implementation details
(DMA address, list pointers) that the upper
layers don't need. Introduce iwl_rx_cmd_buffer
that is passed upstream and only contains the
needed data (the page). Additionally, access
this data only via accessor functions, allowing
us to change the implementation in the future.
These accessors are rxb_addr() (as before) and
rxb_steal_page() to take ownership of the data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When CMD_WANT_SKB is set for a (synchronous)
command, the response is passed back to the
caller which is then responsible for freeing
it. Make this more abstract with real API,
passing directly the response packet in the
new cmd.resp_pkt member and also introduce
iwl_free_resp() to free the pages -- this
way the upper layers don't have to directly
touch the page implementation.
NOTE: This breaks IDI -- the new code isn't reflected there yet!
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We currently use the _irqsafe version, but that
isn't recommended together with ieee80211_rx()
as it can cause races. If the device reports
a TX-status and RX in that order then with the
current combination mac80211 might process them
in the other order, which can cause issues with
powersaving clients.
Use ieee80211_tx_status() to avoid this race.
Since we don't want to call it with locks held,
process the frame queues later -- this is fine
as they are on the stack.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the new WoWLAN flow into the transport
there no longer is a need for this to be
shared, so move it into priv.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the WoWLAN suspend flow, instead of accessing
registers directly, ask the transport to do the
required setup at the end of suspend. If the
transport doesn't implement this, don't tell the
stack we support WoWLAN.
When the device suspends w/o WoWLAN, mac80211
will have stopped it already, which has already
called iwl_apm_stop() via stop_hw(). Thus, it
isn't necessary to call it again in pcie_suspend
and we can simply do nothing there.
This unifies the regular and WoWLAN suspend.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code in the two branches of the #ifdef
is almost the same so move the common code
outside the #ifdef.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Writing to the global config structures
is always wrong. To protect against such
mistakes in the future, mark them const.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's not really a good idea to write to the
global static configuration. Use the valid
TX/RX antenna information only from the HW
params struct except in the case where the
values from the config are used to override
the values from the EEPROM.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no SKU override, we always just use
it from EEPROM. As such, we can remove it
from the config and use it in hw_param only.
Since iwl_eeprom_check_sku() really needs
to fill it in also rename that to
iwl_eeprom_init_hw_params().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need for the per-device debug
level that we expose in debugfs since the
module parameter is writable in sysfs.
At the same time, simplify code by changing
iwl_get_debug_level(shrd) & IWL_DL_ISR)
to
iwl_have_debug_level(IWL_DL_ISR)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With mac80211 now giving us station information
(via the sta_state callback) before auth/assoc
we can get rid of tx_sync by adding the station
early for the case of managed interfaces. Keep
AP mode actions the same for now.
As we now get the BSSID early, we can also get
rid of iwl_reprogram_ap_sta().
We can still optimise the number of RXONs we
send to the device, but that can be done later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no reason to set EXIT_PENDING when we
start removing the module, as mac80211 will
cleanly shut down the device in this case.
Additionally, there's no point in rejecting
commands to the device when we're cleaning up
as that only leads to unwanted errors from
mac80211 being printed, such as
failed to remove key (...) from hardware (-16)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some data doesn't need protection, some of the
lock places are simply useless, and some data
can be protected with the mutex instead. Thus
the shared lock can be removed by making those
changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The statistics are currently only half-heartedly
locked against concurrent reading & modification
so introduce a lock to really protect them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that the transport has its own locking,
there's no need to have the sta_lock in the
shared data. Also, it can be a BH lock as
it's not used from IRQ handlers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of (ab)using the sta_lock, make the
transport layer lock its own TX queue data
structures with a lock per queue. This also
unifies with the cmd queue lock.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the powersave related functions we only need
to set a few parameters for the station command
and can otherwise leave it blank -- there's no
need to copy it from the database.
This allows us to not use the sta lock here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simplify the code by returning directly in the
error case and replacing the switch/if with a
single if statement.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we TX, we hold the sta_lock for a long
time, a lot of which isn't needed. Reduce
the time we hold the lock. Note that this
doesn't really change anything as the code
is already under the other spinlock, but it
makes the code easier to read.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The station ID argument to the function
iwlagn_tx_cmd_build_hwcrypto isn't used
so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's only one place using this function, so
move it where it's needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we only monitor while associated, the following
can happen:
- we're associated, and the queue stuck check
runs, setting the queue "touch" time to X
- we disassociate, stopping the monitoring,
which leaves the time set to X
- almost 2s later, we associate, and enqueue
a frame
- before the frame is transmitted, we monitor
for stuck queues, and find the time set to
X, although it is now later than X + 2000ms,
so we decide that the queue is stuck and
erroneously restart the device
It happens more with P2P because there we can
go between associated/unassociated frequently.
Cc: stable@vger.kernel.org
Reported-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was broken by the commit 023ca58f1
"iwlwifi: Move the core suspend function to iwl-agn-lib"
where for some reason the code changed while moving,
from
.len[0] = sizeof(*key_data.rsc_tsc),
to
.len[0] = sizeof(key_data.rsc_tsc),
Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
drivers/net/ethernet/broadcom/tg3.c
Conflicts in the statistics regression bug fix from 'net',
but happily Matt Carlson originally posted the fix against
'net-next' so I used that to resolve this.
Signed-off-by: David S. Miller <davem@davemloft.net>
This renames the IEEE80211_TX_CTL_POLL_RESPONSE
TX flag to IEEE80211_TX_CTL_NO_PS_BUFFER and also
uses it for non-bufferable MMPDUs (all MMPDUs but
deauth, disassoc and action frames.)
Previously, mac80211 would let the MMPDU through
but not set the flag so drivers supporting some
hardware aids for avoiding the PS races would
then reject the frame.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a fixup for my:
iwlwifi: kill iwl_bus.h
Please fold them into one patch for upstream
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
We can use forward declaration for the relevant struct since they
aren't dereferenced in the header file.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Also add a might_sleep to enforce the context requirements.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This is temporary, but at least we can now throw the bus away
and move the iwl_pci_{probe,remove} functions.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The transport should not dereference the iwl_priv pointer. Remove a
few of those.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Export it as "nic_error" notification, the error handling will be in
the op_mode.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Export it as "hw_rf_kill" notification.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Export them as "queue_full" and "queue_not_full" notification.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This handler allows the transport layer to free an skb from the
op_mode. This can happen when the driver is stopped while Tx
packets are pending in the transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Define the op_mode as an interface with its ops. All the functions
of the op_mode are "private", but its ops is made public in
iwl-op-mode.h.
The drv object starts the op_mode by using the start function in the
public ops.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
iwl_remove stops the wifi flows, so rename.
Moreover, we can possibly stop the wifi flows even if the driver
is statically compiled in the kernel, so remove the __devexit pragma.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Fetch the fw and spawn the op_mode. The op_mode that we need
to fetch is determined from the fw file.
Since the fw is fetched very early in the init flow, we can
determine what op_mode to spawn.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The uCode flags modification is op_mode dependent
since the P2P config is an op-mode config.
This also fixes P2P enabling: due to the uCode
loading code shuffle moving the SKU check before
the EEPROM was read it was always false and would
always disable PAN/P2P.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This will allow to have different behavior depending on the fw.
Different fw APIs require completely different implementation
of the mac80211 APIs. Each of these implementations is called an
op_mode.
The current op_mode is called DVM which states for dual virtual MAC.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
struct iwl_fw contains a string that describe the fw. This string
is now set by the iwl_parse_*_firmware.
This string is later used to update the cfg80211 data.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
drivers/net/wireless/iwlwifi/iwl-core.c included 'iwl-agn.h' twice,
remove the duplicate.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When trying to remove a key, we always send key
flags just setting the key type, not including
the multicast flag and the key ID. As a result,
whenever any key was removed, the unicast key 0
would be removed, causing a complete connection
loss after the second rekey (the first doesn't
cause a key removal). Fix the key removal code
to include the key ID and multicast flag, thus
removing the correct key.
Cc: stable@vger.kernel.org
Reported-by: Alexander Schnaidt <alex.schnaidt@googlemail.com>
Tested-by: Alexander Schnaidt <alex.schnaidt@googlemail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the firmware implements beacon filtering,
beacons are filtered when not associated. This causes
association failures on channels marked passive.
Enabling this flag indicates to the firmware to allow
the beacons to pass through when not associated only.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This will allow to set the hw_params after we fetch the uCode.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The capabilities parsed from the ucode file are never saved. Save
them in the iwl_fw structure.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Remove the references to iwl_priv from the firmware request and
parsing routines. They are generic to the nic.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This allows to handle races such as Tx packets on their way to be
sent although the transport has been stopped already.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Move the ucode offset pointers to the iwl_nic as they are nic related.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Fix a few typos in the existing comments too.
Enforce the comments with might_sleep.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
When a host command is sent through testmode, the whole
reply (including rx header) is returned to the user, and not
only the payload of the rx.
Before this commit the length was buggy - the reply contained 4 bytes
after the end of the payload.
Signed-off-by: Amit Beka <amit.beka@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Fixed casting of buffer addressing, and added size to
the read method, like in __iwl_read_prph.
Signed-off-by: Amit Beka <amit.beka@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Remove another dependency between the nic layer and the iwl_priv
struct.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
iwl_down was just a wrapper around __iwl_down which was called from
one place only. Replace it to direct call to iwl_down. Add lockdep
warning in iwl_down to ensure it was called with the mutex held.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Change the prameters to the ucode (de)allocate routines to iwl_nic as
they are not transport operations.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The ucode image is a ucode related thing not a transport one. Move them.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Move firmware_loading_complete from iwl_priv to iwl_nic and rename it
to more accurately reflect what it does.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Delete firmware_name from iwl_priv and use iwl_nic instead.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Delete fw_index from iwl_priv and use iwl_nic instead.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Delete ucode_ver from iwl_priv and use iwl_nic instead.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Instead of using a global lock, the PCIe transport
can use an own lock for its IRQ. This will make it
possible to not disable IRQs for the shared lock.
The lock is currently used throughout the code but
this can be improved even further by splitting up
the locking for the queues.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
In order to separate the different parts of the
driver better, we are reducing the shared data.
This moves the workqueue to "priv", and removes
it from the transport. To do this, simply use
schedule_work() in the transport.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Make iwlwifi record all debug messages into
tracing, even if debug_level is not enabled.
Due to the lack of APIs, the debug messages
are now recorded up to a max length of 100,
the only one above that is the RXON which is
not needed if you trace the commands as well
as it only dumps the command contents.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
The testmode command for host command send now replies
with a nl80211 message and the response it recieved from
the device.
This does not change the API directly, but adds a reply
to the testmode call.
Signed-off-by: Amit Beka <amit.beka@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Replaced the old SRAM and periphery indirect access functions
with a unified indirect memory access functions. These include
new IWL_TM_CMDs for buffer read/write/dump which replace the
SRAM read/dump commands, but the API for IWL_TM_CMD_INDIRECT_REG
read/write will now not be supported (returns error).
This also handles writing to periphery registers in 1-3 bytes.
Requires the corresponding patch in the library for the API change.
Signed-off-by: Amit Beka <amit.beka@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
A lot of error conditions in testmode log as IWL_DEBUG_INFO which is not
logged by default. Change it
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Booleans should not be compared to true or false
but be directly tested or tested with !.
Done via cocci script:
@@
bool t;
@@
- t == true
+ t
@@
bool t;
@@
- t != true
+ !t
@@
bool t;
@@
- t == false
+ !t
@@
bool t;
@@
- t != false
+ t
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added a check on the direct register access.
Checks that the address is in the lower ragnge (0x0-0x2000),
which belongs to CSR, HBUS and FH registers.
Signed-off-by: Amit Beka <amit.beka@intel.com>
Signed-off-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
smatch correctly complains:
iwl-trans-pcie.c +1528 iwl_trans_pcie_start_hw(50) warn: 'trans->irq' was not released on error
Fix it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
The routines dealing with the ucode are spread through several files.
Move them all to the same file and create a iwl-ucode.h file with the
ucode file definitions.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
There is nothing device specific in the initialization of the
bcast_sta_id so move it to the common inititalization routine.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The message was misleading when a queue is deactivated. The fifo
number is irrelevant then, so don't print it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This trans_ops->stop_hw leaves the RFKILL interrupt enabled,
we can call that one instead of enable_rfkill_int. By that,
we reduce the numbers of acceesses to the NIC from the upper
layers.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The HW revision is now read by the transport layer in its allocation.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Get this information from the transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Get this information from the transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Get this information from the transport layer which is now in charge
of the APM too.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This handler was called from the transport layer only. Merge it
to the transport's apm_init.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Now there is only one transport function that launch a specific fw:
trans_ops->start_fw. This one replaces trans_ops->start_device and
trans_ops->kick_nic. The code that actually loads the fw to the
device has been moved to the transport specific code.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This is another clean up of the proble flow.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This handler stops the HW and puts it in low power state.
It will allow to clean up the flows in the upper layers.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Kill the trans_ops->prepare_card_hw which is now useless.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This handler will become thicker, reflect its real role now.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
From now on, the transport layer in charge of providing access to the
device. So change all the driver to give a pointer to the transport
to all the low level functions that actually access the device.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Most of the accesses to the registers are done from the transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
All the bus configuration is now done in the transport
allocation fucntion.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Change the way we alloc the transport on the way.
Since the transport is allocated from a bus specific area, we can
give the bus specific parameters (i.e. pci_dev for PCI) to the
transport. This will be useful when the bus layer will be killed.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Allocating the shrd area dynamically will allow more agility
while revamping the flows.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
There is no link between the two. Ensure that the NIC is on outside
the code of the EEPROM handling.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This patch connects IDI transport to driver. It does so
by using a number of ifdefs at this stage.
IDI is a new transport that is under development.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Define a new handler in the transport layer API: fw_alive.
Move iwl_reset_ict to this new handler, and move the content
of tx_start to this handler.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
In my AMPDU rework, I rely on the sequence numbers of frames. But
I didn't check that the frame has a valid tid before updating the
tracking counters. As a result, the Tx queues were stalled. People
who hit this bug saw that we simply didn't let any data out.
This bug was introduced in 3.3.
This patch fixes that and checks that the frame is a QoS frame before
looking at its tid and changing the counters.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever the PAN (P2P) context is active, it
has timers in the uCode that prevent sleep,
so scanning can't be out of channel for more
than the beacon interval programmed into the
device.
Before this patch, a full scan including any
passive channels when P2P was active would
stall forever because it wouldn't find time
to execute the passive requests (for default
beacon intervals of 100 TU.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Led has no use for some platform.
Add additional module parameter option to disable LED
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix multiple bugs in event tracing:
1) If you enable uCode tracing with the device down,
it will still attempt to access the device and
continuously log "MAC is in deep sleep!" errors.
Fix this by only starting logging when the device
is actually alive.
2) Now you can set the flag when the device is down,
but logging doesn't happen when you bring it up.
To fix that, start logging when the device comes
alive. This means we don't log before -- we could
do that but I don't need it right now.
3) For some reason we read the error instead of the
event log -- use the right pointer.
4) Optimise SRAM reading of event log header.
5) Fix reading write pointer == capacity, which can
happen due to racy SRAM access
6) Most importantly: fix an error where we would try
to read WAY too many events (like 2^32-300) when
we read the wrap counter before it is updated by
the uCode -- this does happen in practice and will
cause the driver to hang the machine.
7) Finally, change the timer to 10ms instead of 100ms
as 100ms is too slow to capture all data with a
normal event log and with 100ms the log will wrap
multiple times before we have a chance to read it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever the PAN (P2P) context is active, it
has timers in the uCode that prevent sleep,
so scanning can't be out of channel for more
than the beacon interval programmed into the
device.
Before this patch, a full scan including any
passive channels when P2P was active would
stall forever because it wouldn't find time
to execute the passive requests (for default
beacon intervals of 100 TU.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Fix multiple bugs in event tracing:
1) If you enable uCode tracing with the device down,
it will still attempt to access the device and
continuously log "MAC is in deep sleep!" errors.
Fix this by only starting logging when the device
is actually alive.
2) Now you can set the flag when the device is down,
but logging doesn't happen when you bring it up.
To fix that, start logging when the device comes
alive. This means we don't log before -- we could
do that but I don't need it right now.
3) For some reason we read the error instead of the
event log -- use the right pointer.
4) Optimise SRAM reading of event log header.
5) Fix reading write pointer == capacity, which can
happen due to racy SRAM access
6) Most importantly: fix an error where we would try
to read WAY too many events (like 2^32-300) when
we read the wrap counter before it is updated by
the uCode -- this does happen in practice and will
cause the driver to hang the machine.
7) Finally, change the timer to 10ms instead of 100ms
as 100ms is too slow to capture all data with a
normal event log and with 100ms the log will wrap
multiple times before we have a chance to read it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
When an interrupt comes in, we read the reason
bits and collect them into "trans_pcie->inta".
This happens with the spinlock held. However,
there's a bug resetting this variable -- that
happens after the spinlock has been released.
This means that it is possible for interrupts
to be missed if the reset happens after some
other interrupt reasons were already added to
the variable.
I found this by code inspection, looking for a
reason that we sometimes see random commands
time out. It seems possible that this causes
such behaviour, but I can't say for sure right
now since it happens extremely infrequently on
my test systems.
Cc: stable@vger.kernel.org [3.2]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new testmode command IWL_TM_CMD_APP2DEV_GET_FW_INFO for
reporting the following information of existing loaded uCode image.
+ uCode type
+ Instruction section size
+ Data section size
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The error message will be show up by using IWL_ERR
insteads of IWl_DEBUG_INFO.
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables SRAM read function to support entire target memory.
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to make sure the testcommand function of direct register
access can be performed even NIC is asleep, replace corresponding
handler iwl_read32 and iwl_write32 by using iwl_direct_read32 and
iwl_direct_write32.
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On my testing, I saw some strange behavior
[ 421.739708] iwlwifi 0000:01:00.0: ACTIVATE a non DRIVER active station id 148 addr 00:00:00:00:00:00
[ 421.739719] iwlwifi 0000:01:00.0: iwl_sta_ucode_activate Added STA id 148 addr 00:00:00:00:00:00 to uCode
not sure how it happen, but adding the sanity check to prevent memory
corruption
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When enable the testmode from user space and working with uCode, driver does
not own the uCode and should not process the notifications or pkts from uCode
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix the following build warning:
drivers/net/wireless/iwlwifi/iwl-scan.c: In function ‘iwlagn_request_scan’:
drivers/net/wireless/iwlwifi/iwl-scan.c:572: warning: ‘cmd_len’ may be used uninitialized in this function
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace dma_alloc_coherent()+memset() with the new dma_zalloc_coherent()
Signed-off-by: Djalal Harouni <tixxdz@opendz.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
net/bluetooth/l2cap_core.c
Just two overlapping changes, one added an initialization of
a local variable, and another change added a new local variable.
Signed-off-by: David S. Miller <davem@davemloft.net>
The ICT code erroneously uses PAGE_SIZE. The bug
is that PAGE_SIZE isn't necessarily 4096, so on
such platforms this code will not work correctly
as we'll try to attempt to read an index in the
table that the device never wrote, it always has
4096-byte pages.
Additionally, the manual alignment code here is
unnecessary -- Documentation/DMA-API-HOWTO.txt
states:
The cpu return address and the DMA bus master address are both
guaranteed to be aligned to the smallest PAGE_SIZE order which
is greater than or equal to the requested size. This invariant
exists (for example) to guarantee that if you allocate a chunk
which is smaller than or equal to 64 kilobytes, the extent of the
buffer you receive will not cross a 64K boundary.
Just use appropriate new constants and get rid of
the alignment code.
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Runtime DC calibration was previously conditional. Remove this
behaviour, as new devices support runtime DC calibration,
while older devices ignore the runtime DC calibration request.
This patch addresses low TX throughput issues seen with the 6205.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
instead of doing all the work in IWL_TM_CMD_APP2DEV_GET_DEVICE_ID, just use
the information from bus_get_hw_id()
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
At least while debugging, a lot of people use
11n_disable=1 to disable HT completely. To be
able to figure out what parts of HT cause the
problems we see, make the parameter a bitmap,
allowing to disable all of HT and aggregation
(TX/RX) separately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The legacy IRQs could be read from a trace by their
IO accesses, but reading the ICT doesn't leave any
trace (pun intended ;-) ) so in order to see what
input they get we need to add specific tracepoints.
While at it, fix whitespace in two related places.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Since we configure all the queues as CHAINABLE, we need to update the
byte count for all the queues, not only the AGGREGATABLE ones.
Not doing so can confuse the SCD and make the fw assert.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function is not needed:
* we already have the "cmd" input to it in the
same type (and on the stack elsewhere)
* the "legacy_reserved" parameter is never set,
so will always be zero
Remove the function and the stack copy of the
input command.
This is still left from when iwlegacy was part
of the driver -- then we needed a translation
for the command for 3945.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Add new IO function _iwl_write_targ_mem_words() to support
target memory write for a continuous area. It will return
error code -EBUSY if iwl_grab_nic_access() fails to indicate
the memory write does not be performed. Meanwhile the existing
function iwl_write_targ_mem() also been updated by using
_iwl_write_targ_mem_words() in a single word case.
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
These are unused, so can be removed safely. They also
don't make a lot of sense in Bluetooth configuration.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Remove all but the last few references to iwl_priv from the lower
level iwl-ucode.c, with resulting code changes.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The mac80211 setup_register operations are collected in one routine,
but the cleanup routines are not. Create a routine for this.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
If the agg SM is in IWL_EMPTYING_HW_QUEUE_ADDBA or in
IWL_EMPTYING_HW_QUEUE_DELBA, we are not supposed to get Tx packets
from mac80211. mac80211 is supposed to buffer these packets for us.
A few issues have been identified in this mechanism, not all of them
were fixed.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Since my latest patches, the upper layer reports to mac80211 that the
driver is ready to continue the start / stop BA flow as opposed to
the transport layer. Hence, iwl_{start,stop}_tx_ba_trans_ready are
not needed any more.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This will allow us to catch bad cases in which the packets aren't in
the right place on the ring.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Since the station is removed, we need to reset the information that
was accounted for this station.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This is another step towards the move of tid_data from the shared
area.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The tid_data is not related to the transport layer, so move
the logic that depends on it to the upper layer.
This patch deals with the seq_number.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The tid_data is not related to the transport layer, so move
the logic that depends on it to the upper layer.
This patch deals with the mapping of RA / TID to HW queues in AGG.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The tid_data is not related to the transport layer, so move
the logic that depends on it to the upper layer.
This patch deals with the code that checks if there are still
pending packets for an RA / TID.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The tid_data is not related to the transport layer, so move
the logic that depends on it to the upper layer.
This patch deals with tx AGG setup.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The tid_data is not related to the transport layer, so move
the logic that depends on it to the upper layer.
This patch deals with tx AGG alloc.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The tid_data is not related to the transport layer, so move
the logic that depends on it to the upper layer.
This patch deals with tx AGG stop.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
In the same spirit as the previous patch. Eventually this will
allow us to remove the tid_data knowledge from the transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
In the very first implementation of HT, the driver was responsible
for the queueing: stopping and waking the queues while the HW queues
where being drained. In this implementation, we had to deal with the
case where we were draining the AGG queue because we wanted to tear
down the BA agreement.
In the normal flow (when we don't drain any HW queue), when packets
are reclaimed, we wake the SW queue in case the SW queue was stopped
which can happen when the HW queues are too full.
While draining a HW queue, we must make sure that we don't wake the
SW queue, since the whole point of the draining is to empty totally
the HW queue and not only get below a certain threshold.
This is why there is condition in the reclaim function:
if (NOT EMPTYING DELBA)
wake the SW queue is applicable
Since then, a lot has changed and mac80211 is now able to buffer
packets that are being sent to a packet list that will be spliced
after the driver has reported it has drained its HW queues.
Hence, there is no need for the for aforementioned if, and we can
safely wake up the queue even if we are draining HW queues.
Removing this if, also allows us to remove the wake_queue in
check_empty that was there in order to deal with a corner case
created by the if.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Since packets sent to an RA / TID in AGG are sent from a
separate HW Tx queue, we may get into a race:
the regular queue isn't empty while we already begin to
send packets from the AGG queue. This would result in sending
packets out of order.
In order to cope with this, mac80211 waits until the driver
reports that the legacy queue is drained before it can send
packets to the AGG queue. During that time, mac80211 buffers
packets for the driver. These packets will be sent in order
after the driver reports it is ready.
The way this was implemented in the driver is as follows:
We held a counter that monitors the number of packets for
an RA / TID in the HW queues. When this counter reached 0,
we knew that the HW queues were drained and we reported to
mac80211 that were ready to proceed.
This patch changes the implementation described above. We
now remember what is the wifi sequence number of the first
packet that will be sent in the AGG queue (lets' call it
ssn). When we reclaim the packet before ssn, we know that
the queue is drained, and we are ready to proceed.
This will allow us to move this logic in the upper layer and
eventually remove the tid_data from the shared area.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
ba_resp->seq_ctl is __le16, need to translate to cpu endianity.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Replace the engineering names with the marketing names for the
new devices.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Move the configuration pointer from the upper level iwl_priv to the
lower level iwl_shared structure, with associated code fixes.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
My previous patch
34a5b4b6af iwlwifi: do not re-configure
HT40 after associated
Fix the case of HT40 after association on specified AP, but it break the
association for some APs and cause not able to establish connection.
We need to address HT40 before and after addociation.
CC: stable@vger.kernel.org #3.0+
Reported-by: Andrej Gelenberg <andrej.gelenberg@udo.edu>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Tested-by: Andrej Gelenberg <andrej.gelenberg@udo.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ted reported that he couldn't connect to some APs
and bisected it to the tx_sync implementation.
Disable it for the BSS context to fix this issue.
Reported-by: Ted Ts'o <tytso@mit.edu>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check the IEEE80211_TX_CTL_ASSIGN_SEQ flag from mac80211, then decide how to
set the TX_CMD_FLG_SEQ_CTL_MSK bit. Setting the wrong bit in BAR frame whill
make the firmware to increment the sequence number which is incorrect and
cause unknown behavior.
CC: stable@vger.kernel.org #3.0+
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We track the load only on 8 TIDs, previously this
was TID_MAX_LOAD_COUNT. Since IWL_MAX_TID_COUNT
is now 8 as well, use that to make the code more
easily understandable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Now that I corrected IWL_MAX_TID_COUNT to be 8
instead of 9, we can use it in WoWLAN suspend.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The driver everywhere uses max TID count as 9,
which is wrong, it should be 8.
I think the reason it uses 9 here is off-by-one
confusion by whoever wrote this. We do use the
value IWL_MAX_TID_COUNT for "not QoS/no TID"
but that is completely correct even if it is 8
and not 9 since 0-7 are only valid.
As a side effect, this fixes the following bug:
Open BA session requested for 00:23:cd:16:8a:7e tid 8
------------[ cut here ]------------
kernel BUG at drivers/net/wireless/iwlwifi/iwl-trans-pcie-int.h:350!
...
when you do
echo "tx start 8" > /sys/kernel/debug/ieee80211/*/*/*/*/agg_status
Cc: stable@vger.kernel.org
Reported-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Move the calib_results list from the upper layer iwl_priv structure
to the lower layer iwl_trans structure.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Move the low level ucode device_pointers structure to iwl_shared.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The eeprom image is a device level component, move from iwl_priv
to iwl_shared, with associated code changes.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
P2P still under development. it will not enabled by default, but user
always can enable it manually for testing.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Create new tm command to report devce ID information to userspace
- IWL_TM_CMD_APP2DEV_GET_DEVICE_ID
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
