Don't use Amstrad Delta custom I/O functions once GPIO interface is
available for the underlying hardware.
While requesting and initializing GPIO pins used, also take care of one
extra pin KEYBRD_DATAOUT which, even if not used by the driver, belongs
to the device and affects its functioning.
Once done, move the driver initialization back to the device_initcall
level, reverting the temporary chane introduced with patch 1/7 "ARM:
OMAP1: ams-delta: register latch dependent devices later". That change
is no longer required once the driver takes care of registering used
GPIO pins, and it's better to initialize the device before others using
the latch2 based GPIO pins, otherwise a garbage is reported on boot,
perhaps due to random data already captured by the FIQ handler while the
keyboard related latch bits are written with random values during
initialization of those other latch2 dependent devices.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
[tony@atomide.com: renamed _gpios to ams_delta_gpios]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Don't use Amstrad Delta custom I/O functions any longer, use GPIO API
instead.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Don't use Amstrad Delta custom I/O functions for controlling the device,
use GPIO API instead.
While being at it, add missing gpio_free(AMS_DELTA_GPIO_PIN_NAND_RB).
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Cc: David Woodhouse <dwmw2@infradead.org>
Reviewed-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that the Amstrad Delta on-board latches have been converted to GPIO
devices, use the generic driver to control on-board LEDs which hang off
those latches.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Once ready, ams-delta specific device drivers currently calling custom
ams_delta_latch[12]_write() functions can be updated to call generic
gpio_set_value() instead, which will make them less platform dependent.
Even more, some custom ams-delta only drivers can perhaps be dropped
from the tree after converting selected ams-delta platform devices to
follow generic GPIO based device models.
The latch_gpios[] table is initially filled with all latch1 and latch2
GPIO pins in order to register and initialize them from the board file
until those are handled by respective existing device drivers (leds,
nand, lcd, serio, asoc, serial). That table will get almost empty after
the transision process is completed, holding only pins not used by any
drivers / connected to unused devices, in order to initialize them from
the board file for power saving purposes.
The new ams_delta_latch_write() function is a unified replacement for
those removed ams_delta_latch[12]_write(), and serves as a temporary
wrapper over gpio_set_value(), providing the old API for those not yet
updated device drivers, and will be removed after all custom drivers are
converted or replaced.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In preparation to converting Amstrad Delta on-board latches to
basic_mmio_gpio devices, registration of platform devices which depend
on latches and will require initialization of their GPIO pins first,
should be moved out of .machine_init down to late_initcall level, as the
gpio-generic driver is not available until device_initcall time. The
latch reset operation, which will be replaced with GPIO initialization,
must also be moved to late_initcall for the same reason.
Since there was already another, separate arch_initcall function for
setting up one of those latch dependent devices, the on-board modem
device, reuse that function, i.e., rename it to a name that matches the
new purpose, extend with other device setup relocated from
.machine_init, and move down to the late_initcall level.
While being at it, add missing gpio_free() in case the modem platform
device registration fails.
Thanks to Tony Lindgren <tony@atomide.com> who suggested this approach
instead of shifting up the gpio-generic driver initialization.
In addition, defer registration of the Amstrad Delta ASoC and serio
devices, done from their device driver files, until late_initcall time,
as those drivers will depend on their GPIO pins already requested from
the board late_init() function until updated to register their GPIO pins
themselves.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
sched_clock() is yet another blocker on the road to the single
image. This patch implements an idea by Russell King:
http://www.spinics.net/lists/linux-omap/msg49561.html
Instead of asking the platform to implement both sched_clock()
itself and the rollover callback, simply register a read()
function, and let the ARM code care about sched_clock() itself,
the conversion to ns and the rollover. sched_clock() uses
this read() function as an indirection to the platform code.
If the platform doesn't provide a read(), the code falls back
to the jiffy counter (just like the default sched_clock).
This allow some simplifications and possibly some footprint gain
when multiple platforms are compiled in. Among the drawbacks,
the removal of the *_fixed_sched_clock optimization which could
negatively impact some platforms (sa1100, tegra, versatile
and omap).
Tested on 11MPCore, OMAP4 and Tegra.
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Colin Cross <ccross@android.com>
Cc: Erik Gilling <konkers@android.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: STEricsson <STEricsson_nomadik_linux@list.st.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Tested-by: Jamie Iles <jamie@jamieiles.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Krzysztof Halasa <khc@pm.waw.pl>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
DPLL1 reprogramming to a different rate is actually blocked inside
omap1_select_table_rate(). However, it is already forced at boot, for
boards which boot at unusable clock rates, and this seems to work
correctly.
OTOH, we now have a fine, run time performed clock selection algorithm
implemented, which prevents less powerfull SoCs from being overclocked
unintentionally.
Allow reprogramming of dpll1 by default, and use it for switching to the
higest supported clock rate with all boards, including those already
booting at a usable rate of 60 MHz or above.
Created against linux-omap/master tip as of Thu Dec 1,
commit f83c2a8cbb59981722d1ab610c79adfd034a2667. Requires the just
submitted patch "ARM: OMAP1: Move dpll1 rates selection from config to
runtime" to prevent from unintentional overclocking. Tested on Amstrad
Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to comments in omap1_select_table_rate(), reprogramming dpll1
is tricky, and should always be done from SRAM.
While being at it, move OMAP730 special case handling inside
omap_sram_reprogram_clock().
Created on top of version 2 of the series "ARM: OMAP1: Fix dpll1
reprogramming related issues", which it depends on.
Tested on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For still better multi-OMAP1 support, expand omap1_rate_table with flags
for different SoC types and match them while selecting clock rates. The
idea is stolen from current omap24xx clock rate selection algorithm.
Since clkdev platform flag definitions are reused here, those had to be
expanded with one extra entry for OMAP1710 subtype, as this is the only
SoC for which we allow selection of the highest, 216 MHz rate.
Once done, remove no longer needed clock rate configure time options.
Tested on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise timing is inaccurate, resulting in devices which depend on it,
like omap-keypad, broken.
Tested on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
[tony@atomide.com: removed comment referencing a development branch]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the exact value found in omap1_rate_table, otherwise I have been
experiencing issues with correct timekeeping on my Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
[tony@atomide.com: removed comment referencing a development branch]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit e9b7086b80 (ARM: OMAP: Fix
reprogramming of dpll1 rate) fixed a regression for systems that
did not rely on bootloader set rates.
However, it also introduced a new problem where the rates selected
in .config would not take affect as omap1_select_table_rate
currently refuses to reprogram DPLL1 if it's already initialized.
This was not a problem earlier, as the reprogramming was done
earlier with ck_dpll1_p->rate uninitialized.
Fix this by forcing the reprogramming on systems booting at rates
below 60MHz. Note that the long term fix is to make the rates
SoC specific later on.
Thanks for Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> for figuring
this one out.
Reported-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A generic version should replace this later.
As io.c has become nearly empty, omap_init_consistent_dma_size() is moved
into common.c so that io.c can be removed entirely.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Kevin Hilman <khilman@ti.com>
As suggested by Russell King - ARM Linux <linux@arm.linux.org.uk>,
there's no need to keep local prototypes in non-local headers.
Add mach-omap1/common.h and mach-omap2/common.h and move the
local prototypes there from plat/common.h and mach/omap4-common.h.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit a66cb3454f (ARM: OMAP: Map SRAM
later on with ioremap_exec()) moved the SRAM init to happen later
to remove a dependency to early SoC detection for map_io.
This broke booting on some boards not using Kconfig option for
OMAP_CLOCKS_SET_BY_BOOTLOADER as the dpll1 reprogramming would
cause the following error:
kernel BUG at arch/arm/plat-omap/sram.c:226!
Internal error: Oops - undefined instruction: 0 [#1] PREEMPT
Modules linked in:
CPU: 0 Not tainted (3.2.0-rc1-e3 #9)
PC is at omap_sram_reprogram_clock+0x28/0x30
LR is at omap1_select_table_rate+0x88/0xb4
pc : [<c001b0c4>] lr : [<c0019f54>] psr: 600000d3
sp : c035bf10 ip : c035bf20 fp : c035bf1c
r10: c035bfd4 r9 : 54029252 r8 : c03f8120
r7 : c0362b50 r6 : 00b71b00 r5 : c03873cc r4 : c0362b40
r3 : 00000000 r2 : c0362b40 r1 : 0000010a r0 : 00002cb0
Flags: nZCv IRQs off FIQs off Mode SVC_32 ISA ARM Segment kernel
Control: 0000317f Table: 10004000 DAC: 00000017
Process swapper (pid: 0, stack limit = 0xc035a270)
Stack: (0xc035bf10 to 0xc035c000)
bf00: c035bf3c c035bf20 c0019f54 c001b0ac
bf20: 00001000 00002cb3 00000004 c035ed4c c035bf74 c035bf40 c033ea24 c0019edc
bf40: c02f526c 00000002 00000015 bc058c9b 93111a16 c035335c 02000000 c035ed4c
bf60: c035ed4c c03f8120 c035bf84 c035bf78 c00194c4 c033e8ec c035bfc4 c035bf88
bf80: c033bc24 c00194a0 c035bf90 c035bf98 00000000 00000000 00000000 00000000
bfa0: 00000001 00000000 c0354678 c035ece4 10004000 103532f4 c035bff4 c035bfc8
bfc0: c0338574 c033b598 00000000 00000000 00000000 c035467c 0000317d c035c03c
bfe0: c0354678 c035ece4 00000000 c035bff8 10008040 c0338508 00000000 00000000
Backtrace:
[<c001b09c>] (omap_sram_reprogram_clock+0x0/0x30) from [<c0019f54>] (omap1_select_table_rate+0x88/0xb4)
[<c0019ecc>] (omap1_select_table_rate+0x0/0xb4) from [<c033ea24>] (omap1_clk_init+0x148/0x334)
r7:c035ed4c r6:00000004 r5:00002cb3 r4:00001000
[<c033e8dc>] (omap1_clk_init+0x0/0x334) from [<c00194c4>] (omap1_init_early+0x34/0x48)
r8:c03f8120 r7:c035ed4c r6:c035ed4c r5:02000000 r4:c035335c
[<c0019490>] (omap1_init_early+0x0/0x48) from [<c033bc24>] (setup_arch+0x69c/0x79c)
[<c033b588>] (setup_arch+0x0/0x79c) from [<c0338574>] (start_kernel+0x7c/0x2f4)
[<c03384f8>] (start_kernel+0x0/0x2f4) from [<10008040>] (0x10008040)
r7:c035ece4 r6:c0354678 r5:c035c03c r4:0000317d
Code: 0a000002 e1a0e00f e12fff13 e89da800 (e7f001f2)
Fix this by adding omap1_clk_late_init() that only reprograms dpll1
if the bootloader rate is less than 60MHz. This also allows removing
of the OMAP_CLOCKS_SET_BY_BOOTLOADER option.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 7b88e62f5d (ARM: OMAP1: Use generic
map_io, init_early and init_irq) changed omap1 to use generic map_io.
Looks like I missed one board though. Fix this by adding a custom
map_io for Amstrad E3.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
There is no use for omap-alsa.h and board-palmz71.c doesn't need it either.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix "Enable 32kHz OS timer in order to allow sleep states in idle"
warning. We are now compiling in bothe MPU timer and 32 KiHz timer,
so this warning is only valid when MPU_TIMER is set and OMAP_DM_TIMER
is not set.
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'next/cleanup2' of git://git.linaro.org/people/arnd/arm-soc: (31 commits)
ARM: OMAP: Warn if omap_ioremap is called before SoC detection
ARM: OMAP: Move set_globals initialization to happen in init_early
ARM: OMAP: Map SRAM later on with ioremap_exec()
ARM: OMAP: Remove calls to SRAM allocations for framebuffer
ARM: OMAP: Avoid cpu_is_omapxxxx usage until map_io is done
ARM: OMAP1: Use generic map_io, init_early and init_irq
arm/dts: OMAP3+: Add mpu, dsp and iva nodes
arm/dts: OMAP4: Add a main ocp entry bound to l3-noc driver
ARM: OMAP2+: l3-noc: Add support for device-tree
ARM: OMAP2+: board-generic: Add i2c static init
ARM: OMAP2+: board-generic: Add DT support to generic board
arm/dts: Add support for OMAP3 Beagle board
arm/dts: Add initial device tree support for OMAP3 SoC
arm/dts: Add support for OMAP4 SDP board
arm/dts: Add support for OMAP4 PandaBoard
arm/dts: Add initial device tree support for OMAP4 SoC
ARM: OMAP: omap_device: Add a method to build an omap_device from a DT node
ARM: OMAP: omap_device: Add omap_device_[alloc|delete] for DT integration
of: Add helpers to get one string in multiple strings property
ARM: OMAP2+: devices: Remove all omap_device_pm_latency structures
...
Fix up trivial header file conflicts in arch/arm/mach-omap2/board-generic.c
These files will fail to compile if we dont clean them up in advance
and have them include the appropriate headers they need.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These files all make use of one of the EXPORT_SYMBOL variants
or the THIS_MODULE macro. So they will need <linux/export.h>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (63 commits)
PM / Clocks: Remove redundant NULL checks before kfree()
PM / Documentation: Update docs about suspend and CPU hotplug
ACPI / PM: Add Sony VGN-FW21E to nonvs blacklist.
ARM: mach-shmobile: sh7372 A4R support (v4)
ARM: mach-shmobile: sh7372 A3SP support (v4)
PM / Sleep: Mark devices involved in wakeup signaling during suspend
PM / Hibernate: Improve performance of LZO/plain hibernation, checksum image
PM / Hibernate: Do not initialize static and extern variables to 0
PM / Freezer: Make fake_signal_wake_up() wake TASK_KILLABLE tasks too
PM / Hibernate: Add resumedelay kernel param in addition to resumewait
MAINTAINERS: Update linux-pm list address
PM / ACPI: Blacklist Vaio VGN-FW520F machine known to require acpi_sleep=nonvs
PM / ACPI: Blacklist Sony Vaio known to require acpi_sleep=nonvs
PM / Hibernate: Add resumewait param to support MMC-like devices as resume file
PM / Hibernate: Fix typo in a kerneldoc comment
PM / Hibernate: Freeze kernel threads after preallocating memory
PM: Update the policy on default wakeup settings
PM / VT: Cleanup #if defined uglyness and fix compile error
PM / Suspend: Off by one in pm_suspend()
PM / Hibernate: Include storage keys in hibernation image on s390
...
We don't have cpu_is_omapxxxx SoC detection initialized until
SoC detection is initialized from init_early.
Note that with the common map_io we should no longer need
cpu_is_omapxxxx for ioremap.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This allows us to remove omap hacks for map_io.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This allows removing omap hacks for map_io allowing generic
map_io.
Note that in the future we can't do cpu_is_omapxxxx detection
until in init_early. This means that board-innovator.c now
assumes 15xx only, and board-generic.c assumes 16xx only.
This is best fixed later on by passing the SoC type from
device tree.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Boards used to specify zreladdr in their Makefile.boot with
zreladdr-y := x, so conflicting zreladdrs were silently overwritten.
This patch changes this to zreladdr-y += x, so that we end
up with multiple words in zreladdr in such a case. We can
detect this later and complain if necessary.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These address definitions are OMAP1 specific can be in single source file.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Register access can be made more generic by calculating register address
offsets runtime from common register definitions and by using reg_size and
reg_step variables that are passed via platform data. Common register
definitions are possible since McBSP registers are ordered similarly between
OMAP versions.
Remove also references to OMAP2+ specific config_type variable from generic
McBSP code since other variables and feature flags are better to carry needed
information from platform code.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Only OMAP1s are using omap_mcbsp_register_board_cfg after OMAP2+ hwmod
conversion so it can be moved to mach-omap1/mcbsp.c.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This achieves two goals:
1) Get rid of omap_uart_v2p() and omap_uart_p2v() which were the last users
of PLAT_PHYS_OFFSET.
2) Remove the probing of the M bit in the CP15 control reg and make
the access to the .data variables completely position independent.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
This is the first step to remove PLAT_PHYS_OFFSET usage from the debug
UART code.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Some platforms (like OMAP not to name it) are doing rather complicated
hacks just to determine the base UART address to use. Let's give their
addruart macro some slack by providing an extra work register which will
allow for much needed cleanups.
This is basically a no-op as this commit is only adding the extra argument
to the macro but no one is using it yet.
Signed-off-by: nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Convert OMAP1 dmtimers into a platform devices and then registers with
device model framework so that it can be bound to corresponding driver.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Cousson, Benoit <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since the PM clock management code in drivers/base/power/clock_ops.c
is used for both runtime PM and system suspend/hibernation, the
definitions of data structures and headers related to it should not
be located in include/linux/pm_rumtime.h. Move them to a separate
header file.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Convert arch/arm includes of mach/gpio.h and asm/gpio.h to linux/gpio.h
before we start consolidating the individual platform implementations
of the gpio header files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'next/cross-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
ARM: Consolidate the clkdev header files
ARM: set vga memory base at run-time
ARM: convert PCI defines to variables
ARM: pci: make pcibios_assign_all_busses use pci_has_flag
ARM: remove unnecessary mach/hardware.h includes
pci: move microblaze and powerpc pci flag functions into asm-generic
powerpc: rename ppc_pci_*_flags to pci_*_flags
Fix up conflicts in arch/microblaze/include/asm/pci-bridge.h
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'next/cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (133 commits)
ARM: EXYNOS4: Change devname for FIMD clkdev
ARM: S3C64XX: Cleanup mach/regs-fb.h from mach-s3c64xx
ARM: S5PV210: Cleanup mach/regs-fb.h from mach-s5pv210
ARM: S5PC100: Cleanup mach/regs-fb.h from mach-s5pc100
ARM: S3C24XX: Use generic s3c_set_platdata for devices
ARM: S3C64XX: Use generic s3c_set_platdata for OneNAND
ARM: SAMSUNG: Use generic s3c_set_platdata for NAND
ARM: SAMSUNG: Use generic s3c_set_platdata for USB OHCI
ARM: SAMSUNG: Use generic s3c_set_platdata for HWMON
ARM: SAMSUNG: Use generic s3c_set_platdata for FB
ARM: SAMSUNG: Use generic s3c_set_platdata for TS
ARM: S3C64XX: Add PWM backlight support on SMDK6410
ARM: S5P64X0: Add PWM backlight support on SMDK6450
ARM: S5P64X0: Add PWM backlight support on SMDK6440
ARM: S5PC100: Add PWM backlight support on SMDKC100
ARM: S5PV210: Add PWM backlight support on SMDKV210
ARM: EXYNOS4: Add PWM backlight support on SMDKC210
ARM: EXYNOS4: Add PWM backlight support on SMDKV310
ARM: SAMSUNG: Create a common infrastructure for PWM backlight support
clocksource: convert 32-bit down counting clocksource on S5PV210/S5P64X0
...
Fix up trivial conflict in arch/arm/mach-imx/mach-scb9328.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6: (51 commits)
PM: Improve error code of pm_notifier_call_chain()
PM: Add "RTC" to PM trace time stamps to avoid confusion
PM / Suspend: Export suspend_set_ops, suspend_valid_only_mem
PM / Suspend: Add .suspend_again() callback to suspend_ops
PM / OPP: Introduce function to free cpufreq table
ARM / shmobile: Return -EBUSY from A4LC power off if A3RV is active
PM / Domains: Take .power_off() error code into account
ARM / shmobile: Use genpd_queue_power_off_work()
ARM / shmobile: Use pm_genpd_poweroff_unused()
PM / Domains: Introduce function to power off all unused PM domains
OMAP: PM: disable idle on suspend for GPIO and UART
OMAP: PM: omap_device: add API to disable idle on suspend
OMAP: PM: omap_device: add system PM methods for PM domain handling
OMAP: PM: omap_device: conditionally use PM domain runtime helpers
PM / Runtime: Add new helper function: pm_runtime_status_suspended()
PM / Domains: Queue up power off work only if it is not pending
PM / Domains: Improve handling of wakeup devices during system suspend
PM / Domains: Do not restore all devices on power off error
PM / Domains: Allow callbacks to execute all runtime PM helpers
PM / Domains: Do not execute device callbacks under locks
...
* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6: (61 commits)
gpio/mxc/mxs: fix build error introduced by the irq_gc_ack() renaming
mcp23s08: add i2c support
mcp23s08: isolate spi specific parts
mcp23s08: get rid of setup/teardown callbacks
gpio/tegra: dt: add binding for gpio polarity
mcp23s08: remove unused work queue
gpio/da9052: remove a redundant assignment for gpio->da9052
gpio/mxc: add device tree probe support
ARM: mxc: use ARCH_NR_GPIOS to define gpio number
gpio/mxc: get rid of the uses of cpu_is_mx()
gpio/mxc: add missing initialization of basic_mmio_gpio shadow variables
gpio: Move mpc5200 gpio driver to drivers/gpio
GPIO: DA9052 GPIO module v3
gpio/tegra: Use engineering names in DT compatible property
of/gpio: Add new method for getting gpios under different property names
gpio/dt: Refine GPIO device tree binding
gpio/ml-ioh: fix off-by-one for displaying variable i in dev_err
gpio/pca953x: Deprecate meaningless device-tree bindings
gpio/pca953x: Remove dynamic platform data pointer
gpio/pca953x: Fix IRQ support.
...
Now most of ARM machines has the alsmot same __clk_get/put() macro
So place it at the arch/arm/include/asm/clkdev.h and remove the reduntant header files
But some machines don't have the same form as above. It can use the machince specific clkdev file by HAVE_MACH_CLKDEV config
Now there are only 3 caese.
1) define the clk structure with clkdev macro => Need to move clk structure to proper header file
arch/arm/mach-versatile/include/mach/clkdev.h
arch/arm/mach-realview/include/mach/clkdev.h
arch/arm/mach-vexpress/include/mach/clkdev.h
arch/arm/mach-integrator/include/mach/clkdev.h
2) export the __clk_get/put function at clock.c
arch/arm/mach-shmobile/include/mach/clkdev.h
3) demuxing the clk source
arch/arm/mach-u300/include/mach/clkdev.h
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
* pm-domains: (33 commits)
ARM / shmobile: Return -EBUSY from A4LC power off if A3RV is active
PM / Domains: Take .power_off() error code into account
ARM / shmobile: Use genpd_queue_power_off_work()
ARM / shmobile: Use pm_genpd_poweroff_unused()
PM / Domains: Introduce function to power off all unused PM domains
PM / Domains: Queue up power off work only if it is not pending
PM / Domains: Improve handling of wakeup devices during system suspend
PM / Domains: Do not restore all devices on power off error
PM / Domains: Allow callbacks to execute all runtime PM helpers
PM / Domains: Do not execute device callbacks under locks
PM / Domains: Make failing pm_genpd_prepare() clean up properly
PM / Domains: Set device state to "active" during system resume
ARM: mach-shmobile: sh7372 A3RV requires A4LC
PM / Domains: Export pm_genpd_poweron() in header
ARM: mach-shmobile: sh7372 late pm domain off
ARM: mach-shmobile: Runtime PM late init callback
ARM: mach-shmobile: sh7372 D4 support
ARM: mach-shmobile: sh7372 A4MP support
ARM: mach-shmobile: sh7372: make sure that fsi is peripheral of spu2
ARM: mach-shmobile: sh7372 A3SG support
...
These McBSP port number enums are used only in two places in the McBSP code
so we may remove then and just use numeric values like rest of the code does.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pointers to statically declared platform device structures which are
registered with platform_device_register() are then used during run time
to access these structure members, for example from platform_uevent()
and much more. Therefore, these structures should never be placed inside
sections which are dropped after boot. Fix platform devices incorrectly
tagged with __initdata which happen to exist inside OMAP sub-trees.
This bug has exhibited itself on my ARM/OMAP1 based Amstrad Delta
videophone after commit 6d3163ce86, "mm:
check if any page in a pageblock is reserved before marking it
MIGRATE_RESERVE", resulting in reading from several
/sys/device/platform/*/uevent files always ending up with segmentation
faults.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Varadarajan, Charulatha <charu@ti.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The common PM clock management functions may be used for system
suspend/resume as well as for runtime PM, so rename them
accordingly. Modify kerneldoc comments describing these functions
and kernel messages printed by them, so that they refer to power
management in general rather that to runtime PM.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Kevin Hilman <khilman@ti.com>
The naming convention used by commit 7538e3db6e015e890825fbd9f86599b
(PM: Add support for device power domains), which introduced the
struct dev_power_domain type for representing device power domains,
evidently confuses some developers who tend to think that objects
of this type must correspond to "power domains" as defined by
hardware, which is not the case. Namely, at the kernel level, a
struct dev_power_domain object can represent arbitrary set of devices
that are mutually dependent power management-wise and need not belong
to one hardware power domain. To avoid that confusion, rename struct
dev_power_domain to struct dev_pm_domain and rename the related
pointers in struct device and struct pm_clk_notifier_block from
pwr_domain to pm_domain.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Kevin Hilman <khilman@ti.com>
There's no need to initialize the dmtimer framework early.
Just mark the clocksource and timesource as reserved, and
initialize dmtimer with an arch_initcall.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
This is needed for the following patches so we can initialize the
rest of the hardware timers later on.
As with the init_irq calls, there's no need to do cpu_is_omap calls
during the timer init as we only care about the major omap generation.
This means that we can initialize the sys_timer with the .timer
entries alone.
Note that for now we just set stubs for the various sys_timer entries
that will get populated in a later patch. The following patches will
also remove the omap_dm_timer_init calls and change the init for the
rest of the hardware timers to happen with an arch_initcall.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Remove cpu_is_* checks from gpio_show_revision() by passing in the
revision address offset from platform data. SoCs with no revision
register (15xx, 7xx, and all MPUIOs) use -1 (actually, USHRT_MAX) to
signify no register.
While here, all GPIO banks are assumed to be the same revision, so fix
show_revision() to only show the revision for the first bank it finds.
This removes duplicate GPIO revision prints during boot.
Thanks to Charulatha V <charu@ti.com> for finding/fixing a few -1s
that were missed in the original patch.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Cleanup GPIO IRQ enable/disable handling by removing SoC-specific
Also split enable/disable IRQ into separate functions for better
readability and also facilitate potentially moving to generic irq_chip
in the future.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Cleanup IRQ status handling by passing IRQ status register offsets
via platform data.
Cleans up clearing of GPIO IRQ status and GPIO ISR handler.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add register offset fields to GPIO platform_data for registers.
This patch adds registers that control direction, input and output
data. Using these register offsets in the common driver allows
removal of #ifdefs and greatly improves readability.
Also create dedicated data out functions: one for banks with dedicated
set/clear registers, and another for banks with a single mask
register.
Signed-off-by: Kevin Hilman <khilman@ti.com>
This allows us to remove cpu_is_omap calls from init_irq functions.
There should not be any need for cpu_is_omap calls as at this point.
During the timer init we only care about SoC generation, and not about
subrevisions.
The main reason for the patch is that we want to initialize only
minimal omap specific code from the init_early call.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
When runtime PM is disabled, device clocks need to be enabled on
device add and disabled on device remove. This currently is not
happening because in the !PM_RUNTIME case, no notifiers are registered
for OMAP1 devices.
Fix this by ensuring notifiers are registered, even in the !PM_RUNTIME case.
Reported-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Platform_device_del should be called before platform_device_put, as
platform_device_put can delete the structure.
Additionally, improve the error handling code for the call to ioremap, so
that it calls platform_device_put.
The semantic match that finds this problem is:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2;
@@
*platform_device_put(e1);
... when != e1 = e2
*platform_device_del(e1);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert the OMAP1 32-bit down counting clocksource to the generic
clocksource infrastructure.
Tested-by: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The OMAP1 clocksource interrupt handler just increments a variable
which otherwise isn't used, so this seems to be unnecessary. Tony
Lindgren confirms, so lets remove it.
Acked-by: Kevin Hilman <khilman@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The set_vpp() method provided by physmap passes a map_info back to
the platform code, which has little relevance as far as the platform
is concerned (this parameter is completely unused).
Instead, pass the platform_device, which can be used in the pismo
driver to retrieve some important information in a nicer way, instead
of the hack that was in place.
The empty set_vpp function in board-at572d940hf_ek.c is left untouched,
as the board/SoC is scheduled for removal.
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Acked-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert OMAP1 to using the new generic clock manipulation routines
and a device power domain for runtime PM instead of overriding the
platform bus type's runtime PM callbacks. This allows us to simplify
OMAP1-specific code and to share some code with other platforms
(shmobile in particular).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Kevin Hilman <khilman@ti.com>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (258 commits)
omap: zoom: host should not pull up wl1271's irq line
arm: plat-omap: iommu: fix request_mem_region() error path
OMAP2+: Common CPU DIE ID reading code reads wrong registers for OMAP4430
omap4: mux: Remove duplicate mux modes
omap: iovmm: don't check 'da' to set IOVMF_DA_FIXED flag
omap: iovmm: disallow mapping NULL address when IOVMF_DA_ANON is set
omap2+: mux: Fix compile when CONFIG_OMAP_MUX is not selected
omap4: board-omap4panda: Initialise the serial pads
omap3: board-3430sdp: Initialise the serial pads
omap4: board-4430sdp: Initialise the serial pads
omap2+: mux: Add macro for configuring static with omap_hwmod_mux_init
omap2+: mux: Remove the use of IDLE flag
omap2+: Add separate list for dynamic pads to mux
perf: add OMAP support for the new power events
OMAP4: Add IVA OPP enteries.
OMAP4: Update Voltage Rail Values for MPU, IVA and CORE
OMAP4: Enable 800 MHz and 1 GHz MPU-OPP
OMAP3+: OPP: Replace voltage values with Macros
OMAP3: wdtimer: Fix CORE idle transition
Watchdog: omap_wdt: add fine grain runtime-pm
...
Fix up various conflicts in
- arch/arm/mach-omap2/board-omap3evm.c
- arch/arm/mach-omap2/clock3xxx_data.c
- arch/arm/mach-omap2/usb-musb.c
- arch/arm/plat-omap/include/plat/usb.h
- drivers/usb/musb/musb_core.h
Commit 3cf32bba8c ("OMAP: McBSP: Convert
McBSP to platform device model") breaks compilation with non-multi-OMAP1
configs:
CC arch/arm/mach-omap1/mcbsp.o
arch/arm/mach-omap1/mcbsp.c: In function 'omap1_mcbsp_init':
arch/arm/mach-omap1/mcbsp.c:384: warning: dereferencing 'void *' pointer
arch/arm/mach-omap1/mcbsp.c:387: error: invalid use of void expression
arch/arm/mach-omap1/mcbsp.c:390: warning: dereferencing 'void *' pointer
arch/arm/mach-omap1/mcbsp.c:393: error: invalid use of void expression
Fix by avoiding NULL dereferences.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
[tony@atomide.com: updated description not to remove unnecessary branch name]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Implement McBSP as platform device and add support for
registering through platform device layer using resource
structures.
Later in this patch series, OMAP2+ McBSP driver would be modified to
use hwmod framework after populating the omap2+ hwmod database.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These are needed for CONFIG_ARM_PATCH_PHYS_VIRT to work.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
after these changes omap1_defconfig and omap2plus_defconfig don't have any
section mismatches any more, making it plausible that the patches earlier
in this series are OK.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These are only called from omap_nokia770_init which is in .init.text, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The new fncpy API is better suited* for copying some
code to SRAM at runtime. This patch changes the ad-hoc
code to the more generic fncpy API.
*: 1. fncpy ensures that the thumb mode bit is propagated,
2. fncpy provides the security of type safety between the
original function and the sram function pointer.
Tested OK on OMAP3 in low power modes (RET/OFF)
using omap2plus_defconfig with !CONFIG_THUMB2_KERNEL.
Compile tested on OMAP1/2 using omap1_defconfig.
Boot tested on OMAP1 & OMAP2
Tested OK with suspend/resume on OMAP2420/n810
Boots fine on osk5912 and n800
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Kevin Hilman <khilman@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes bug introduced in revision:
f8e9e98454
omap1: DMA: move LCD related code from plat-omap to mach-omap1
The code introduced by this patch didn't consider any other CPUs but OMAP1510,
which rendered OMAP310 -- which has the same LCD controller -- non-working. Use
cpu_is_omap15xx() instead of cpu_is_omap1510() to squash this issue.
Bug found on Palm Zire 71 hardware.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Eliminates the following sparse warnings:
arch/arm/mach-omap1/board-voiceblue.c:253:6: warning: symbol 'voiceblue_wdt_enable' was not declared. Should it be static?
arch/arm/mach-omap1/board-voiceblue.c:261:6: warning: symbol 'voiceblue_wdt_disable' was not declared. Should it be static?
arch/arm/mach-omap1/board-voiceblue.c:269:6: warning: symbol 'voiceblue_wdt_ping' was not declared. Should it be static?
arch/arm/mach-omap1/board-voiceblue.c:278:6: warning: symbol 'voiceblue_reset' was not declared. Should it be static?
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds a clean method to allow platforms to hook into the reset
code if they require to.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Eliminates the following sparse warning:
arch/arm/mach-omap1/board-h3.c:207:27: warning: symbol 'nand_platdata' was not declared. Should it be static?
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Eliminates the following sparse warnings:
arch/arm/mach-omap1/board-htcherald.c:334:34: warning: symbol 'htcpld_chips' was not declared. Should it be static?
arch/arm/mach-omap1/board-htcherald.c:369:34: warning: symbol 'htcpld_pfdata' was not declared. Should it be static?
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Eliminates the following sparse warning:
arch/arm/mach-omap1/board-innovator.c:368:13: warning: symbol 'innovator_mmc_init' was not declared. Should it be static?
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Eliminates the following sparse warning:
arch/arm/mach-omap1/board-h2.c:205:27: warning: symbol 'h2_nand_platdata' was not declared. Should it be static?
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the following section mismatches:
WARNING: arch/arm/mach-omap1/built-in.o(.data+0x491c): Section mismatch
in reference from the variable fsample_config to the (unknown reference)
.init.data:(unknown)
The variable fsample_config references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the
variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: arch/arm/mach-omap1/built-in.o(.data+0x8f0c): Section mismatch
in reference from the variable ams_delta_config to the (unknown
reference) .init.data:(unknown)
The variable ams_delta_config references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the
variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: arch/arm/mach-omap1/built-in.o(.data+0x93ac): Section mismatch
in reference from the variable ams_delta_camera_device to the (unknown
reference) .init.data:(unknown)
The variable ams_delta_camera_device references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the
variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: vmlinux.o(.data+0x5e94): Section mismatch in reference from the
variable fsample_config to the (unknown reference) .init.data:(unknown)
The variable fsample_config references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the
variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: vmlinux.o(.data+0xa484): Section mismatch in reference from the
variable ams_delta_config to the (unknown reference)
.init.data:(unknown)
The variable ams_delta_config references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the
variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: vmlinux.o(.data+0xa924): Section mismatch in reference from the
variable ams_delta_camera_device to the (unknown reference)
.init.data:(unknown)
The variable ams_delta_camera_device references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the
variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the following compile warning:
arch/arm/mach-omap1/board-palmte.c:233:13: warning:
'palmte_headphones_detect' defined but not used
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 03a9e51261
(omap1: Use asm_irq_flags for entry-macro.S) added support
for multi-omap builds with addition of the omap_irq_flags.
Commit 9f9605c2ed
(omap2+: Fix unused variable warning for omap_irq_base)
simplified omap2+ entry-macro.S by moving omap_irq_flags
out of entry-macro.S.
Simplify omap1 entry-macro.S in a similar way to keep the
code consistent. Based on a similar earlier patch for omap2+
by Russell King <rmk+kernel@arm.linux.org.uk>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Earlier patches select HAVE_SCHED_CLOCK for omaps. To have working sched_clock
also for MPU timer, we need to implement it in a way where the right one gets
selected during the runtime.
Signed-off-by: Tony Lindgren <tony@atomide.com>
For omap15xx and 730 we need to use the MPU timer
as the 32K timer is not available. For omap16xx
we want to use the 32K timer because of PM. Fix this
by allowing to build in both timers.
Signed-off-by: Tony Lindgren <tony@atomide.com>
After commit dc548fbbd2 ("ARM: omap: convert
sched_clock() to use new infrastructure"), OMAPs that use the 32KiHz
"synchronization timer" as their clocksource crash during boot:
[ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz
[ 0.000000] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 0.000000] pgd = c0004000
[ 0.000000] [00000000] *pgd=00000000
[ 0.000000] Internal error: Oops: 80000005 [#1] SMP
[ 0.000000] last sysfs file:
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 Tainted: G W (2.6.37-07734-g2467802 #7)
[ 0.000000] PC is at 0x0
[ 0.000000] LR is at sched_clock_poll+0x2c/0x3c
[ 0.000000] pc : [<00000000>] lr : [<c0060b74>] psr: 600001d3
[ 0.000000] sp : c058bfd0 ip : c058a000 fp : 00000000
[ 0.000000] r10: 00000000 r9 : 411fc092 r8 : 800330c8
[ 0.000000] r7 : c05a08e0 r6 : c0034c48 r5 : c05ffc40 r4 : c0034c4c
[ 0.000000] r3 : c05ffe6c r2 : c05a0bc0 r1 : c059f098 r0 : 00000000
[ 0.000000] Flags: nZCv IRQs off FIQs off Mode SVC_32 ISA ARM Segment kernel
[ 0.000000] Control: 10c53c7f Table: 8000404a DAC: 00000017
This is due to the recent ARM init_sched_clock() changes and the late
initialization of the counter_32k clock source. More information here:
http://marc.info/?l=linux-omap&m=129513468605208&w=2
Fix by initializing the counter_32k clocksource during the machine timer
initialization.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
* git://git.infradead.org/mtd-2.6: (59 commits)
mtd: mtdpart: disallow reading OOB past the end of the partition
mtd: pxa3xx_nand: NULL dereference in pxa3xx_nand_probe
UBI: use mtd->writebufsize to set minimal I/O unit size
mtd: initialize writebufsize in the MTD object of a partition
mtd: onenand: add mtd->writebufsize initialization
mtd: nand: add mtd->writebufsize initialization
mtd: cfi: add writebufsize initialization
mtd: add writebufsize field to mtd_info struct
mtd: OneNAND: OMAP2/3: prevent regulator sleeping while OneNAND is in use
mtd: OneNAND: add enable / disable methods to onenand_chip
mtd: m25p80: Fix JEDEC ID for AT26DF321
mtd: txx9ndfmc: limit transfer bytes to 512 (ECC provides 6 bytes max)
mtd: cfi_cmdset_0002: add support for Samsung K8D3x16UxC NOR chips
mtd: cfi_cmdset_0002: add support for Samsung K8D6x16UxM NOR chips
mtd: nand: ams-delta: drop omap_read/write, use ioremap
mtd: m25p80: add debugging trace in sst_write
mtd: nand: ams-delta: select for built-in by default
mtd: OneNAND: lighten scary initial bad block messages
mtd: OneNAND: OMAP2/3: add support for command line partitioning
mtd: nand: rearrange ONFI revision checking, add ONFI 2.3
...
Fix up trivial conflict in drivers/mtd/Kconfig as per DavidW.
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (243 commits)
omap2: Make OMAP2PLUS select OMAP_DM_TIMER
OMAP4: hwmod data: Fix alignment and end of line in structurefields
OMAP4: hwmod data: Move the DMA structures
OMAP4: hwmod data: Move the smartreflex structures
OMAP4: hwmod data: Fix missing SIDLE_SMART_WKUP in smartreflexsysc
arm: omap: tusb6010: add name for MUSB IRQ
arm: omap: craneboard: Add USB EHCI support
omap2+: Initialize serial port for dynamic remuxing for n8x0
omap2+: Add struct omap_board_data and use it for platform level serial init
omap2+: Allow hwmod state changes to mux pads based on the state changes
omap2+: Add support for hwmod specific muxing of devices
omap2+: Add omap_mux_get_by_name
OMAP2: PM: fix compile error when !CONFIG_SUSPEND
MAINTAINERS: OMAP: hwmod: update hwmod code, data maintainership
OMAP4: Smartreflex framework extensions
OMAP4: hwmod: Add inital data for smartreflex modules.
OMAP4: PM: Program correct init voltages for scalable VDDs
OMAP4: Adding voltage driver support
OMAP4: Register voltage PMIC parameters with the voltage layer
OMAP3: PM: Program correct init voltages for VDD1 and VDD2
...
Fix up trivial conflict in arch/arm/plat-omap/Kconfig
There is a common requirement for not using OMAP specific omap_readw() /
omap_writew() function calls in drivers/, but replace them with
readw() / writew() on ioremap()ped addresses passed from arch/ instead.
The patch implements this idea for the Amstrad Delta NAND driver. To be
able to use the modified driver, the board file is updated with the
platform device I/O resource declaration, which is passed from there.
Created and tested against linux-2.6.37-rc5, on top of recent patch
'MTD: NAND: ams-delta: convert to platform driver'.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In its current form, the driver may interfere with different hardware on
different boards if built into the kernel, hence is not suitable for
inclusion into a defconfig, inteded to be usable with multiple OMAP1 cpu and
machine types.
Convert it to a platform driver, that should be free from this issue.
Created and tested against linux-2.6.37-rc5 on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Most keypad drivers make use of the <linux/input/matrix_keypad.h>
defined macros, structures and inline functions.
Convert omap-keypad driver to use those as well, as suggested by a
compile time warning, hardcoded into the OMAP <palt/keypad.h>.
Created against linux-2.6.37-rc5.
Tested on Amstrad Delta.
Compile tested with omap1_defconfig and omap2plus_defconfig shrinked to
board-h4.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Reviewed-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
Otherwise multi-omap1 configurations may set wrong clock speed.
Created and tested against l-o master on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
No need to call this early from init_irq. Also recent changes
initialize GPIO now later, so calling gpio_request from init_irq
will make it fail.
While at it, also remove the unnecessary EXPORT_SYMBOL.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert DMA library into DMA platform driver and make use of
platform data provided by hwmod data base for OMAP2+ onwards.
For OMAP1 processors, the DMA driver in mach-omap uses resource
structures for getting platform data.
Thanks to Tony Lindgren <tony@atomide.com> for fixing various
omap1 issues and testing the same on OSK5912 board.
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Implement OMAP1 DMA as platform device and add support for
registering through platform device layer using resource
structures.
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The convention for omap device naming is omap_XXX.
Rename the device and driver name in order to stick
to this naming convention.
Change device name in clock nodes as well.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Ben Dooks <ben-i2c@fluff.org>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix following compilation warning:
arch/arm/mach-omap1/pm_bus.c: In function 'omap1_pm_runtime_resume':
arch/arm/mach-omap1/pm_bus.c:51: warning: unused variable 'ret'
Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Patch fix following compilation warning:
arch/arm/mach-omap1/board-htcherald.c:442:
warning: large integer implicitly truncated to unsigned type
Hopefully this is just a typo.
Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise multi-omap1 support for omap1 won't work as the cpu_class_is_omap1()
won't work until the SoC is detected.
Note that eventually these will go away, please use ioremap + read/write instead.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Initialize asm_irq_flags in omap_init_irq and use it in
get_irqnr_and_base to detect between omap7xx and omap15xx/16xx.
Note that both INT_1510_IH2_IRQ and INT_1510_IH2_IRQ are defined
as 0, so use INT_1510_IH2_IRQ for both of them.
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to divide the 15xx/16xx offset by 2 for 7xx. Use bank->stride
for that. This allows us to get rid of the duplicate defines for the
MPUIO registers.
Note that this will cause omap-keypad.c driver to not work on 7xx.
However, the right fix there is to move over to matrix_keypad instead
as suggested by Cory Maccarrone <darkstar6262@gmail.com> and
Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>.
Cc: Cory Maccarrone <darkstar6262@gmail.com>
Acked-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Implement GPIO as a platform device.
GPIO APIs are used in machine_init functions. Hence it is
required to complete GPIO probe before board_init. Therefore
GPIO device register and driver register are implemented as
postcore_initcalls.
omap_gpio_init() does nothing now and this function would be
removed in the next patch as it's usage is spread across most
of the board files.
Inorder to convert GPIO as platform device, modifications are
required in clockxxxx_data.c file for OMAP1 so that device names
can be used to obtain clock instead of getting clocks by
name/NULL ptr.
Use runtime pm APIs (pm_runtime_put*/pm_runtime_get*) for enabling
or disabling the clocks, modify sysconfig settings and remove usage
of clock FW APIs.
Note 1: Converting GPIO driver to use runtime PM APIs is not done as a
separate patch because GPIO clock names are different for various OMAPs
and are different for some of the banks in the same CPU. This would need
usage of cpu_is checks and bank id checks while using clock FW APIs in
the gpio driver. Hence while making GPIO a platform driver framework,
PM runtime APIs are used directly.
Note 2: While implementing GPIO as a platform device, pm runtime APIs
are used as mentioned above and modification is not done in gpio's
prepare for idle/ resume after idle functions. This would be done
in the next patch series and GPIO driver would be made to use dev_pm_ops
instead of sysdev_class in that series only.
Due to the above, the GPIO driver implicitly relies on
CM_AUTOIDLE = 1 on its iclk for power management to work, since the
driver never disables its iclk.
This would be taken care in the next patch series (see Note 3 below).
Refer to
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg39112.html
for more details.
Note 3: only pm_runtime_get_sync is called in gpio's probe() and
pm_runtime_put* is never called. This is to make the implementation
similar to the existing GPIO code. Another patch series would be sent
to correct this.
In OMAP3 and OMAP4 gpio's debounce clocks are optional clocks. They
are enabled/ disabled whenever required using clock framework APIs
TODO:
1. Cleanup the GPIO driver. Use function pointers and register
offest pointers instead of using hardcoded values
2. Remove all cpu_is_ checks and OMAP specific macros
3. Remove usage of gpio_bank array so that only
instance specific information is used in driver code
4. Rename 'method'/ avoid it's usage
5. Fix the non-wakeup gpios handling for OMAP2430, OMAP3 & OMAP4
6. Modify gpio's prepare for idle/ resume after idle functions
to use runtime pm implentation.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Basak, Partha <p-basak2@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: updated for bank specific revision and updated boards]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for handling OMAP7xx specific gpio_init by
providing platform device data and doing device registration.
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for handling OMAP16xx specific gpio_init by
providing platform device data and doing device registration.
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for handling OMAP15xx specific gpio_init by
providing platform device data and doing device registration.
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like some boards are calling gpio_request from init_irq.
This will make the request_irq fail, as GPIO will be initialized
as postcore_initcall.
Reported-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Define MDR1 register serial definitions used in serial and
bluetooth drivers.
Change magic number to ones defined in serial_reg for omap1/2
serial driver.
Remove redefined MDR1 register definitions in omap-serial driver.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Acked-by: G, Manjunath Kondaiah <manjugk@ti.com>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patches removes a config option that was used to select a FIQ
handler to be build for Amstrad Delta, as required by the on-board serio
interface driver. Not having any problem reports received since it was
introduced in 2.6.35, the FIQ handler can now be built and initialized by
default, thus reqiring no extra config option.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
factorise some generic infrastructure to assist looking up struct clks
for the ARM & SH architecture.
as the code is identical at 99%
put the arch specific code for allocation as example in asm/clkdev.h
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use IOMEM() macro to get rid of the following sparse warning:
arch/arm/mach-omap1/board-ams-delta.c:319:36: warning: incorrect type in initializer (different address spaces)
arch/arm/mach-omap1/board-ams-delta.c:319:36: expected void [noderef] <asn:2>*membase
arch/arm/mach-omap1/board-ams-delta.c:319:36: got void *<noident>
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
