Rearrange the allocation of the mm_struct registration to avoid
allocating underneath the i915->mm_lock, so that we avoid tainting the
lock (and in turn many other locks that may be held as i915->mm_lock is
taken, and those locks we may want on the free [shrinker] paths). In
doing so, we convert the lookup to be RCU protected by courtesy of
converting the free-worker to be an rcu_work.
v2: Remember to use hash_rcu variants to protect the list iteration from
concurrent add/del.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200619194038.5088-1-chris@chris-wilson.co.uk
Often we seem to detect an underrun right after modeset on gen2.
It seems to be a spurious detection (potentially the pipe is still
in a wonky state when we enable the planes). An extra vblank wait
seems to cure it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429101034.8208-13-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
The default fbc1 compression interval we use is 500 frames. That
translates to over 8 seconds typically. That's rather excessive
so let's drop it to 1 second.
The hardware will not attempt recompression unless at least one
line has been modified, so a shorter compression interval should
not cause extra bandwidth use in the purely idle scenario. Of
course in the mostly idle case we are possibly going to recompress
a bit more.
Should really try to find some kind of sweet spot to minimize
the energy usage...
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429101034.8208-11-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
The hardware host tracking won't nuke the entire cfb (unless the
entire fb is written through the gtt) so don't clear the busy_bits
for gtt tracking.
Not that it really matters anymore since we've lost ORIGIN_GTT usage
everywhere.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429101034.8208-7-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
The current fence_y_offset calculation is broken. I think it more or
less used to do the right thing, but then I changed the plane code
to put the final x/y source offsets back into the src rectangle so
now it's just subtraacting the same value from itself. The code would
never have worked if we allowed the framebuffer to have a non-zero
offset.
Let's do this in a better way by just calculating the fence_y_offset
from the final plane surface offset. Note that we don't align the
plane surface address to fence rows so with horizontal panning there's
often a horizontal offset from the fence start to the surface address
as well. We have no way to tell the hardware about that so we just
ignore it. Based on some quick tests the invlidation still happens
correctly. I presume due to the invalidation nuking at least the full
line (or a segment of multiple lines).
Fixes: 54d4d719fa ("drm/i915: Overcome display engine stride limits via GTT remapping")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429101034.8208-4-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Currently there is no null check for a failed memory allocation
on the dsb object and without this a null pointer dereference
error can occur. Fix this by adding a null check.
Note: added a drm_err message in keeping with the error message style
in the function.
Addresses-Coverity: ("Dereference null return")
Fixes: afeda4f3b1 ("drm/i915/dsb: Pre allocate and late cleanup of cmd buffer")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200616114221.73971-1-colin.king@canonical.com
A single Ri mismatch doesn't automatically mean that the link integrity
is broken. Update and check of Ri and Ri' are done asynchronously. In
case an update happens just between the read of Ri' and the check against
Ri there will be a mismatch even if the link integrity is fine otherwise.
Signed-off-by: Oliver Barta <oliver.barta@aptiv.com>
Reviewed-by: Sean Paul <sean@poorly.run>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200504123524.7731-1-oliver.barta@aptiv.com
The linetime watermark is a 9 bit value, which gives us
a maximum linetime of just below 64 usec. If the linetime
exceeds that value we currently just discard the high bits
and program the rest into the register, which angers the
state checker.
To avoid that let's just clamp the value to the max. I believe
it should be perfectly fine to program a smaller linetime wm
than strictly required, just means the hardware may fetch data
sooner than strictly needed. We are further reassured by the
fact that with DRRS the spec tells us to program the smaller
of the two linetimes corresponding to the two refresh rates.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200625200003.12436-1-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
The DP spec says:
"The transmitter shall support at least three levels of voltage
swing (Levels 0, 1, and 2).
If only three levels of voltage swing are supported (VOLTAGE
SWING SET field (bits 1:0) are programmed to 10 (Level 2)),
this bit shall be set to 1, and cleared in all other cases.
If all four levels of voltage swing are supported (VOLTAGE
SWING SET field (bits 1:0) are programmed to 11 (Level 3)),
this bit shall be set to 1,and cleared in all other cases."
Let's follow that exactly instead of the current apporach
where we can set those also for vswing/preemph levels 0 or 1
(or 2 when the platform max is 3).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200512174145.3186-7-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Catch up with upstream, in particular to get c1e8d7c6a7 ("mmap locking
API: convert mmap_sem comments").
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The spec requires enabling the MST Virtual Channel payload allocation
- in a separate step - after the transcoder is enabled, follow this.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200623082411.3889-1-imre.deak@intel.com
UAPI Changes:
- Add DRM_MODE_TYPE_USERDEF for video modes specified in cmdline.
Cross-subsystem Changes:
- Assorted devicetree binding updates.
- Add might_sleep() to dma_fence_wait().
- Fix fbdev's get_user_pages_fast() handling, and use pin_user_pages.
- Small cleanup with IS_BUILTIN in video/fbdev drivers.
- Fix video/hdmi coding style for infoframe size.
Core Changes:
- Silence vblank output during init.
- Fix DP-MST corruption during send msg timeout.
- Clear leak in drm_gem_objecs_lookup().
- Make newlines work with force connector attribute.
- Fix module refcounting error in drm_encoder_slave, and use new i2c api.
- Header fix for drm_managed.c
- More struct_mutex removal for !legacy drivers:
- Remove gem_free_object()
- Removal of drm_gem_object_put_unlocked().
- Show current->comm alongside pid in debug printfs.
- Add drm_client_modeset_check() + drm_client_framebuffer_flush().
- Replace drm_fb_swab16 with drm_fb_swap that also supports 32-bits.
- Remove mode->vrefresh, and compactify drm_display_mode.
- Use drm_* macros for logging and warnings.
- Add WARN when drm_gem_get_pages is used on a private obj.
- Handle importing and imported dmabuf better in shmem helpers.
- Small fix for drm/mm hole size comparison, and remove invalid entry optimization.
- Add a drm/mm selftest.
- Set DSI connector type for DSI panels.
- Assorted small fixes and documentation updates.
- Fix DDI I2C device registration for MST ports, and flushing on destroy.
- Fix master_set return type, used by vmwgfx.
- Make the drm_set/drop_master ioctl symmetrical.
Driver Changes:
Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4, i915, omap, fbdev/sm712fb, fbdev/pxafb, console/newport_con, msm, virtio, udl, malidp, hdlcd, bridge/ti-sn65dsi86, panfrost.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4 (multiple), i915.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE TX26D202VM0BWA panel.
- Use GEM CMA functions in arc, arm, atmel-hlcdc, fsi-dcu, hisilicon, imx, ingenic, komeda, malidp, mcde, meson, msxfb, rcar-du, shmobile, stm, sti, tilcdc, tve200, zte.
- Remove gem_print_info.
- Improve gem_create_object_helper so udl can use shmem helpers.
- Convert vc4 dt bindings to schemas, and add clock properties.
- Device initialization cleanups for mgag200.
- Add a workaround to fix DP-MST short pulses handling on broken hardware in i915.
- Allow build test compiling arm drivers.
- Use managed pci functions in mgag200 and ast.
- Use dev_groups in malidp.
- Add per pixel alpha support for PX30 VOP in rockchip.
- Silence deferred probe logs in panfrost.
-----BEGIN PGP SIGNATURE-----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=ZmKI
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2020-06-19' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.9:
UAPI Changes:
- Add DRM_MODE_TYPE_USERDEF for video modes specified in cmdline.
Cross-subsystem Changes:
- Assorted devicetree binding updates.
- Add might_sleep() to dma_fence_wait().
- Fix fbdev's get_user_pages_fast() handling, and use pin_user_pages.
- Small cleanup with IS_BUILTIN in video/fbdev drivers.
- Fix video/hdmi coding style for infoframe size.
Core Changes:
- Silence vblank output during init.
- Fix DP-MST corruption during send msg timeout.
- Clear leak in drm_gem_objecs_lookup().
- Make newlines work with force connector attribute.
- Fix module refcounting error in drm_encoder_slave, and use new i2c api.
- Header fix for drm_managed.c
- More struct_mutex removal for !legacy drivers:
- Remove gem_free_object()
- Removal of drm_gem_object_put_unlocked().
- Show current->comm alongside pid in debug printfs.
- Add drm_client_modeset_check() + drm_client_framebuffer_flush().
- Replace drm_fb_swab16 with drm_fb_swap that also supports 32-bits.
- Remove mode->vrefresh, and compactify drm_display_mode.
- Use drm_* macros for logging and warnings.
- Add WARN when drm_gem_get_pages is used on a private obj.
- Handle importing and imported dmabuf better in shmem helpers.
- Small fix for drm/mm hole size comparison, and remove invalid entry optimization.
- Add a drm/mm selftest.
- Set DSI connector type for DSI panels.
- Assorted small fixes and documentation updates.
- Fix DDI I2C device registration for MST ports, and flushing on destroy.
- Fix master_set return type, used by vmwgfx.
- Make the drm_set/drop_master ioctl symmetrical.
Driver Changes:
Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4, i915, omap, fbdev/sm712fb, fbdev/pxafb, console/newport_con, msm, virtio, udl, malidp, hdlcd, bridge/ti-sn65dsi86, panfrost.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4 (multiple), i915.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE TX26D202VM0BWA panel.
- Use GEM CMA functions in arc, arm, atmel-hlcdc, fsi-dcu, hisilicon, imx, ingenic, komeda, malidp, mcde, meson, msxfb, rcar-du, shmobile, stm, sti, tilcdc, tve200, zte.
- Remove gem_print_info.
- Improve gem_create_object_helper so udl can use shmem helpers.
- Convert vc4 dt bindings to schemas, and add clock properties.
- Device initialization cleanups for mgag200.
- Add a workaround to fix DP-MST short pulses handling on broken hardware in i915.
- Allow build test compiling arm drivers.
- Use managed pci functions in mgag200 and ast.
- Use dev_groups in malidp.
- Add per pixel alpha support for PX30 VOP in rockchip.
- Silence deferred probe logs in panfrost.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/001cd9a6-405d-4e29-43d8-354f53ae4e8b@linux.intel.com
During encoder enabling we clear the flag before starting the ACT
sequence and wait for the flag, but the clearing is missing during
encoder disabling, add it there too. Since nothing cleared the flag
automatically we could've run subsequent disabling steps too early.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200616141855.746-5-imre.deak@intel.com
It's not clear if the DP_TP_STATUS flags other than the ACT sent flag
have some side-effect, so don't clear those; we don't depend on the
state of these flags anyway.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200616141855.746-4-imre.deak@intel.com
During transcoder enabling we'll configure the transcoder in MST mode
and enable the VC payload allocation, which will start the ACT sequence.
Before waiting for the ACT sequence completion, we need to clear the ACT
sent flag, but based on the above we can do this right before enabling
the transcoder.
For clarity, move the flag clearing closer to where we wait for it.
While at it also factor out some common code.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200616141855.746-3-imre.deak@intel.com
During the initial probing of an MST sink, MST core will determine the
sink's link bandwidth based on its own version of the sink link
rate/lane count caps it reads from the DPCD. At a later point (after
probing and 1 or more modesets) i915 may limit the link parameters wrt.
the original source/sink common caps above due to link training failures
during a modeset and the resulting link training fallback logic.
Based on the above a modeset following another modeset with a link
training error will compute the i915 HW specific and DP protocol timing
parameters (data/link M/N and MST TU values) taking into account only
the unlimited source/sink common caps, but not taking into account the
fallback limits. This will also let DRM core oversubscribe the actual
link bandwidth during the MST payload allocation.
Prevent the above problem by disabling the link training fallback on MST
links for now, until the MST probe time initialization and the MST
compute config logic can deal with changing link parameters.
The misconfigured timings lead at least to a
'Timed out waiting for DP idle patterns'
error.
v2: (Ville)
- Print link training error message on the MST path too.
- Clarify the problem in the commit log.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200616211146.23027-2-imre.deak@intel.com
MST encoders must use the master MST transcoder's DP_TP_STATUS and
DP_TP_CONTROL registers. Atm, during the HW readout of an MST encoder
connected to a slave transcoder we reset these register addresses in
intel_dp::regs.dp_tp_* to the slave transcoder's DP_TP_* register
addresses incorrectly; fix this.
One example where the above overwite happens is the encoder HW state
validation after enabling multiple streams; see
intel_dp_mst_enc_get_config(). After that during disabling any stream
we'll get a
'Timed out waiting for ACT sent when disabling'
error, due to reading from the incorrect DP_TP_STATUS register.
This change replaces
https://patchwork.freedesktop.org/patch/369577/?series=78193&rev=1
which just papered over the problem.
v2:
- Correct the failure scenario in the commit log. (José)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200616211146.23027-1-imre.deak@intel.com
Start using device specific parameters instead of module parameters for
most things. The module parameters become the immutable initial values
for i915 parameters. The device specific parameters in i915->params
start life as a copy of i915_modparams. Any later changes are only
reflected in the debugfs.
The stragglers are:
* i915.force_probe and i915.modeset. Needed before dev_priv is
available. This is fine because the parameters are read-only and never
modified.
* i915.verbose_state_checks. Passing dev_priv to I915_STATE_WARN and
I915_STATE_WARN_ON would result in massive and ugly churn. This is
handled by not exposing the parameter via debugfs, and leaving the
parameter writable in sysfs. This may be fixed up in follow-up work.
* i915.inject_probe_failure. Only makes sense in terms of the module,
not the device. This is handled by not exposing the parameter via
debugfs.
v2: Fix uc i915 lookup code (Michał Winiarski)
Cc: Juha-Pekka Heikkilä <juha-pekka.heikkila@intel.com>
Cc: Venkata Sandeep Dhanalakota <venkata.s.dhanalakota@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20200618150402.14022-1-jani.nikula@intel.com
Pull i2c fixes from Wolfram Sang:
- a small collection of remaining API conversion patches (all acked)
which allow to finally remove the deprecated API
- some documentation fixes and a MAINTAINERS addition
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: Add robert and myself as qcom i2c cci maintainers
i2c: smbus: Fix spelling mistake in the comments
Documentation/i2c: SMBus start signal is S not A
i2c: remove deprecated i2c_new_device API
Documentation: media: convert to use i2c_new_client_device()
video: backlight: tosa_lcd: convert to use i2c_new_client_device()
x86/platform/intel-mid: convert to use i2c_new_client_device()
drm: encoder_slave: use new I2C API
drm: encoder_slave: fix refcouting error for modules
We only emit the renderstate once now during module load, it is no
longer a concern that we are delaying context creation and so do not
need to so eagerly optimise. Since the last time we have looked at the
renderstate, we have a pin_map / flush_map facility that supports simple
single mappings, replacing the open-coded kmap_atomic() and
prepare_write. As it should be a single page, of which we only write a
small portion, we stick to a simple WB [kmap] and use clflush on !llc
platforms, rather than creating a temporary WC vmapping for the single
page.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200619234543.17499-2-chris@chris-wilson.co.uk
Since gvt calls pin_map for the shadow batch buffer, this makes the
action of prepare_write [+pin_pages] redundant. We can write into the
obj->mm.mapping directory and the flush_map routine knows when it has to
flush the cpu cache afterwards.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200619234543.17499-1-chris@chris-wilson.co.uk
Smatch warns that we may iterate over an empty array of gt->engines[].
One hopes that this is impossible, but nevertheless we can simply
appease smatch by initialising the timestamp to zero before we starting
probing the busy-time from the engines.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200619151938.21740-1-chris@chris-wilson.co.uk
The caller expects panfrost_job_hw_submit() to increase
runtime PM usage counter. The refcount decrement on the
error branch of WARN_ON() will break the counter balance
and needs to be removed.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200522134109.27204-1-dinghao.liu@zju.edu.cn
The calls to panfrost_devfreq_record_busy() and
panfrost_devfreq_record_idle() must be balanced to ensure that the
devfreq utilisation is correctly reported. But there are two cases where
this doesn't work correctly.
In panfrost_job_hw_submit() if pm_runtime_get_sync() fails or the
WARN_ON() fires then no call to panfrost_devfreq_record_busy() is made,
but when the job times out the corresponding _record_idle() call is
still made in panfrost_job_timedout(). Move the call up to ensure that
it always happens.
Secondly panfrost_job_timedout() only makes a single call to
panfrost_devfreq_record_idle() even if it is cleaning up multiple jobs.
Move the call inside the loop to ensure that the number of
_record_idle() calls matches the number of _record_busy() calls.
Fixes: 9e62b885f7 ("drm/panfrost: Simplify devfreq utilisation tracking")
Acked-by: Alyssa Rosenzweig <alyssa.rosenzweig@collabora.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200522153653.40754-1-steven.price@arm.com
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
This code was detected with the help of Coccinelle and, audited and
fixed manually.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200617220331.GA19550@embeddedor
i2c_new_client() is deprecated, use the replacement
i2c_new_client_device(). Also, we have a helper to check if a driver is
bound. Use it to simplify the code. Note that this changes the errno for
a failed device creation from ENOMEM to ENODEV. No callers currently
interpret this errno, though, so we use this condensed error check.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
module_put() balances try_module_get(), not request_module(). Fix the
error path to match that.
Fixes: 2066facca4 ("drm/kms: slave encoder interface.")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The ti_sn_bridge_gpio_set() got the return value of
regmap_update_bits() but didn't check it. The function can't return
an error value, but we should at least print a warning if it didn't
work.
This fixes a compiler warning about setting "ret" but not using it.
Fixes: 27ed2b3f22 ("drm/bridge: ti-sn65dsi86: Export bridge GPIOs to Linux")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200612123003.v2.4.Ia4376fd88cdc6e8f8b43c65548458305f82f1d61@changeid
When building we were getting an error:
warning: cannot understand function prototype:
'const unsigned int ti_sn_bridge_dp_rate_lut[] = '
Arrays aren't supposed to be marked with "/**" kerneldoc comments. Fix.
Fixes: a095f15c00 ("drm/bridge: add support for sn65dsi86 bridge driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200612123003.v2.2.If3807e4ebf7f0440f64c3069edcfac9a70171940@changeid
The kernel test robot noted that if "OF" is defined (which is needed
to select DRM_TI_SN65DSI86 at all) but not OF_GPIO that we'd get
compile failures because some of the members that we access in "struct
gpio_chip" are only defined "#if defined(CONFIG_OF_GPIO)".
All the GPIO bits in the driver are all nicely separated out. We'll
guard them with the same "#if defined" that the header has and add a
little stub function if OF_GPIO is not defined.
Fixes: 27ed2b3f22 ("drm/bridge: ti-sn65dsi86: Export bridge GPIOs to Linux")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200612123003.v2.1.Ibe95d8f3daef01e5c57d4c8c398f04d6a839492c@changeid
There is no point to print deferred probe (and its failures to get
resources) as an error. Also there is no need to print regulator errors
twice.
In case of multiple probe tries this would pollute the dmesg.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200527200544.7849-1-krzk@kernel.org
Return the monotonic timestamp (ktime_get()) at the time of sampling the
busy-time. This is used in preference to taking ktime_get() separately
before or after the read seqlock as there can be some large variance in
reported timestamps. For selftests trying to ascertain that we are
reporting accurate to within a few microseconds, even a small delay
leads to the test failing.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200617130916.15261-2-chris@chris-wilson.co.uk
A couple of very simple tests to ensure that the basic properties of
per-engine busyness accounting [0% and 100% busy] are faithful.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200617130916.15261-1-chris@chris-wilson.co.uk
Add rename the gpu busy percentage for consistency and
add the mem busy percentage documentation.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Nirmoy Das <nirmoy.das@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Vega10 and previous asics use one interface, vega20 and newer
use another.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Acked-by: Nirmoy Das <nirmoy.das@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The existing code used the major version number of the DRM driver
instead of the device major number of the DRM subsystem for
validating access for a devices cgroup.
This meant that accesses allowed by the devices cgroup weren't
permitted and certain accesses denied by the devices cgroup were
permitted (if they matched the wrong major device number).
Signed-off-by: Lorenz Brun <lorenz@brun.one>
Fixes: 6b855f7b83 ("drm/amdkfd: Check against device cgroup")
Reviewed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Compared to its predecessors, the PX30 VOP has a different register layout
for enabling per-pixel alpha. Instead of src_alpha_ctl and dst_alpha_ctl,
there is a single alpha control register. This register takes some fields
from src_alpha_ctl, but with a different layout.
Add support for the required fields to the PX30 VOP window descriptions,
which makes per-pixel-alpha formats behave correctly.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20200416140526.262533-1-paul.kocialkowski@bootlin.com
Like live_unlite_ring, but instead of simply looking at the impact of
intel_ring_direction(), check that preemption more generally works with
different depths of queued requests in the ring.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200616233733.18050-1-chris@chris-wilson.co.uk
