Add Toshiba S1800-814 to whitelist for both pata_ali and alim15x3,
as it is correctly detected as 40-wire connected but this cable is
short enough to still use transfer modes higher than UDMA33.
Signed-off-by: Daniel Exner <dex@dragonslave.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The Marvell bridge chips used on HighPoint SATA cards do not seem to support
the UltraDMA modes 1, 2, and 3 as well as any MWDMA modes, so the driver needs
to account for this in the udma_filter() method. In order to achieve that, do
the following changes:
- install the method for all chips, not only HPT36x/370 and improve the code
formatting by killing the extra tabs while at it;
- add to the end of the 'switch' statement in the method cases for HPT372[AN]
and HPT374 chips upon which the known SATA cards are based;
- use hwif->ultra_mask as a default mask for the ide_dma_filter() method to
behave correctly;
- move the HPT370[A] cases below the HPT36x case for consistency.
While at it, replace the explicit UltraDMA mode masks with ATA_UDMA* constants
all over the driver...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bob Ham <rah@bash.sh>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make the SATA drive detection code from eighty_ninty_three() into inline
ide_dev_is_sata() helper fixing it along the way to be more strict while
checking word 80 for the reserved values...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
HPT374 BIOS seems to only save f_CNT register value for the function #0 before
re-tuning DPLL (that causes the driver to report obviously distorted f_CNT for
the function #1) -- fix this by always reading the saved f_CNT register value
from the function #0 in the driver's init_chipset() method.
While at it, introduce 'chip_type' for holding the 'struct hpt_info' field
of the same name and replace the structure assignment with memcpy()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver erroneously "lets go" the mate IDE chip in init_setup_pdc20270()
when ide_setup_pci_devices() call succeeds -- fix this, and drop a couple of
useless assignments in this function while at it...
Bart: keep "findev" variable initialization to silence gcc
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The IDE core never marked the PCI IDE devices as being in use after succesfull
driver probe call (the devices were marked in use only while being probed), and
so was susceptible to issues caused by unsolicited PCI hotplug device removal.
So, add pci_dev_get() call to ide_scan_pcidev() and convert this function to
the kernel style, also dropping a bunch of useless curly braces from its caller,
ide_scan_pcibus() and somewhat beautifying printk() call there, while at it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Currently the mpc8xx ide driver will only work on arch/ppc so only
allow it to be built there. Also, killed a minor include that isn't
actually used by the driver.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata clear horkage on ata_dev_init()
[libata, IDE] add new VIA bridge to VIA PATA drivers
pata_it821x: fix lost interrupt with atapi devices
Fix broken pata_via cable detection
dev->horkage should be cleared over device hotunplug/plug. Clear it
in ata_dev_init().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The earlier crash dump fix on x86_64 depended on patches in -mm which
are intended for post-2.6.23. Without those, it broke the build when
it went into 2.6.23-rc5.
This changes the field references in ELF_CORE_COPY_REGS back to those
still used in mainline.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the case when an nmi gets stucks the endflag stays equal to zero.
This causes the busy looping on other cpus to continue, even though the
nmi test is done.
On my machine with out the change below the system would hang right
after check_nmi_watchdog(). The change below just sets endflag prior to
checking if the test was successful or not.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The CLFLUSH for the modified code line in text_poke was supposed
to speed up CPU recovery. Unfortunately it seems to cause hangs
on some VIA C3s (at least on VIA Esther Model 10 Stepping 9)
Remove it.
Thanks to Stefan Becker for reporting/testing.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the NMI watchdog on Intel CoreDuo processor where the kernel would
get stuck during boot. The issue is related to errata AE49, where the
PERFEVTSEL1 counter does not have a working enable bit. Thus it is not
possible to use it for NMI.
The patch creates a dedicated wd_ops for CoreDuo which falls back to
using PERFEVTSEL0. The other Intel processors supporting the
architectural PMU will keep on using PERFEVTSEL1 as this allows other
subsystems, such as perfmon, to use PERFEVTSEL0 for PEBS monitoring in
particular. Bug initially reported by Daniel Walker.
AK: Added comments
Signed-off-by: Stephane Eranian <eranian@hpl.hp.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fsid_source decided where to get the 'fsid' number to
return for a GETATTR based on the type of filehandle.
It can be from the device, from the fsid, or from the
UUID.
It is possible for the filehandle to be inconsistent
with the export information, so make sure the export information
actually has the info implied by the value returned by
fsid_source.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: "Luiz Fernando N. Capitulino" <lcapitulino@gmail.com>
Signed-off-by: "J. Bruce Fields" <bfields@citi.umich.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recent changes in NFSd cause a directory which is mounted-on
to not appear properly when the filesystem containing it is exported.
*exp_get* now returns -ENOENT rather than NULL and when
commit 5d3dbbeaf5
removed the NULL checks, it didn't add a check for -ENOENT.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When PTRACE_SYSCALL was used and then PTRACE_DETACH is used, the
TIF_SYSCALL_TRACE flag is left set on the formerly-traced task. This
means that when a new tracer comes along and does PTRACE_ATTACH, it's
possible he gets a syscall tracing stop even though he's never used
PTRACE_SYSCALL. This happens if the task was in the middle of a system
call when the second PTRACE_ATTACH was done. The symptom is an
unexpected SIGTRAP when the tracer thinks that only SIGSTOP should have
been provoked by his ptrace calls so far.
A few machines already fixed this in ptrace_disable (i386, ia64, m68k).
But all other machines do not, and still have this bug. On x86_64, this
constitutes a regression in IA32 compatibility support.
Since all machines now use TIF_SYSCALL_TRACE for this, I put the
clearing of TIF_SYSCALL_TRACE in the generic ptrace_detach code rather
than adding it to every other machine's ptrace_disable.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix "lost" interrupt problem when using dma with CD/DVD drives in some
configurations. This problem can make installing linux from media
impossible for distro's that have switched to libata-only configurations.
The simple fix is to eliminate the use of dma for reading drive status, etc,
by checking the number of bytes to transferred.
This change will only affect the behavior of atapi devices, not disks.
There is more info at http://bugzilla.redhat.com/show_bug.cgi?id=242229
This patch is for 2.6.22.1
Signed-off-by: Jeff Norden <jnorden@math.tntech.edu>
Reviewed-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Ocelot: remove remaining bits
[MIPS] TLB: Fix instruction bitmasks
[MIPS] R10000: Fix wrong test in dma-default.c
[MIPS] Provide empty irq_enable_hazard definition for legacy and R1 cores.
[MIPS] Sibyte: Remove broken dependency on EXPERIMENTAL from SIBYTE_SB1xxx_SOC.
[MIPS] Kconfig: whitespace cleanup.
[MIPS] PCI: Set need_domain_info if controller domain index is non-zero.
[MIPS] BCM1480: Fix computation of interrupt mask address register.
[MIPS] i8259: Add disable method.
[MIPS] tty: add the new ioctls and definitions.
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c-algo-bit: Read block data bugfix
i2c-pxa: Fix adapter number
i2c-gpio: Fix adapter number
Following a strict interpretation the empty definition of irq_enable_hazard
has always been a bug - but an intentional one because it didn't bite.
This has now changed, for uniprocessor kernels mm/slab.c:do_drain()
[...]
on_each_cpu(do_drain, cachep, 1, 1);
check_irq_on();
[...]
may be compiled into a mtc0 c0_status; mfc0 c0_status sequence resulting
in a back-to-back hazard.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/sibyte/bcm1480/irq.o
arch/mips/sibyte/bcm1480/irq.c: In function 'bcm1480_mask_irq':
arch/mips/sibyte/bcm1480/irq.c:112: warning: cast to pointer from integer of different size
arch/mips/sibyte/bcm1480/irq.c:114: warning: cast to pointer from integer of different size
arch/mips/sibyte/bcm1480/irq.c: In function 'bcm1480_unmask_irq':
arch/mips/sibyte/bcm1480/irq.c:130: warning: cast to pointer from integer of different size
arch/mips/sibyte/bcm1480/irq.c:132: warning: cast to pointer from integer of different size
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Same as all the others, just put in the constants for the existing kernel
code and termios2 structure
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Previously, ibmebus derived a device's bus_id from its location code.
The location code is not guaranteed to be unique, so we might get bus_id
collisions if two devices share the same location code. The OFDT
full_name, however, is unique, so we use that instead (truncating it
on the left if it is too long).
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On PS3, A storage device may show up in the repository before the hypervisor
has finished probing:
- If its type is not yet known, it shows up as PS3_DEV_TYPE_STOR_DUMMY,
- If its regions are being probed, it shows up as having zero regions.
If any of these happen, consider the device not yet present. The storage
probe thread will retry later.
This fixes the timing-dependent problem where a kernel booted from FLASH ROM
sometimes cannot find the hard disk.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At present, running any SPE program on the ps3 will trigger a BUG_ON
when spufs_run_spu tries to clear the master run control bit, as lv1
does not make the master run control available to Linux.
This change makes SPE apps work again by disabling changes to the
master run control on PS3. Although we don't have the facility to
disable a SPE with supervisor-level privileges, it's better than
hitting the BUG_ON unconditionally.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The Cell BE Architecture spec states that the SPU MFC Class 0 interrupt
is edge-triggered. The current spu interrupt handler assumes this
behavior and does not clear the interrupt status.
The PS3 hypervisor visualizes all SPU interrupts as level, and on return
from the interrupt handler the hypervisor will deliver a new virtual
interrupt for any unmasked interrupts which for which the status has not
been cleared. This fix clears the interrupt status in the interrupt
handler.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The previous patch had the conditional inverted. This patch fixes it
so that we return the original position if it does not straddle a page.
Thanks to Bob Gilligan for spotting this.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This fixes a bug in the way i2c-algo-bit handles I2C_M_RECV_LEN,
used to implement i2c_smbus_read_block_data(). Previously, in the
absence of PEC (rarely used!) it would NAK the "length" byte:
S addr Rd [A] [length] NA
That prevents the subsequent data bytes from being read:
S addr Rd [A] [length] { A [data] }* NA
The primary fix just reorders two code blocks, so the length used
in the "should I NAK now?" check incorporates the data which it
just read from the slave device.
However, that move also highlighted other fault handling glitches.
This fixes those by abstracting the RX path ack/nak logic, so it
can be used in more than one location. Also, a few CodingStyle
issues were also resolved.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
It turns out that platform_device.id is a "u32" so testing it for being
nonnegative is useless when setting up an i2c adapte. Instead,
do what the platform_bus code does and test it against the value "-1".
Signed-off-by: Jean Delvare <khali@linux-fr.org>
It turns out that platform_device.id is a "u32" so testing it for being
nonnegative is useless when setting up an i2c bitbang device. Instead,
do what the platform_bus code does and test it against the value "-1".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix an off-by-one error in the I/O region declaration of two
hardware monitoring drivers (lm78 and w83781d.) We were requesting
one extra port at the end of the region.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The function blkcipher_get_spot tries to return a buffer of
the specified length that does not straddle a page. It has
an off-by-one bug so it may advance a page unnecessarily.
What's worse, one of its callers doesn't provide a buffer
that's sufficiently long for this operation.
This patch fixes both problems. Thanks to Bob Gilligan for
diagnosing this problem and providing a fix.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fixes (papers over) "Sleep problems with kernels >= 2.6.21 on powerpc",
http://lkml.org/lkml/2007/8/25/155. The issue is that the FireWire
controller's pci_dev.current_state of iBook G3 and presumably older
PowerBooks is still in PCI_UNKNOWN instead of PCI_D0 when the firewire
driver's .suspend method is called.
Like it was suggested earlier in http://lkml.org/lkml/2006/10/24/13, we
do not fail .suspend anymore if pci_set_power_state failed.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
