Change the powerpc hpte_insert routines now called through ppc_md to
static scope.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Apparently we've copied the todc drivers, for various RTCs used in
embedded machines from ARCH=ppc to ARCH=powerpc, despite the fact that
it's never used in the latter. This patch removes it.
If we ever need these drivers (which we probably shouldn't now the RTC
class stuff is in), we can transfer them one by one from ARCH=ppc,
removing from the hideous abomination which is the todc
"infrastructure".
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Without this patch, on an idle system I get:
cpu-power-0:21.638
cpu-power-1:27.102
cpu-power-2:29.343
cpu-power-3:25.784
Total: 103.8W
With this patch:
cpu-power-0:11.730
cpu-power-1:17.185
cpu-power-2:18.547
cpu-power-3:17.528
Total: 65.0W
If I lower HZ to 100, I can get it as low as:
cpu-power-0:10.938
cpu-power-1:16.021
cpu-power-2:17.245
cpu-power-3:16.145
Total: 60.2W
Another (older) Quad G5 went from 54W to 39W at HZ=250.
Coming back out of Deep Nap takes 40-70 cycles longer than coming back
from just Nap (which already takes quite a while). I don't think it'll
be a performance issue (interrupt latency on an idle system), but in
case someone does measurements feel free to report them.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This implements a lazy strategy for disabling interrupts. This means
that local_irq_disable() et al. just clear the 'interrupts are
enabled' flag in the paca. If an interrupt comes along, the interrupt
entry code notices that interrupts are supposed to be disabled, and
clears the EE bit in SRR1, clears the 'interrupts are hard-enabled'
flag in the paca, and returns. This means that interrupts only
actually get disabled in the processor when an interrupt comes along.
When interrupts are enabled by local_irq_enable() et al., the code
sets the interrupts-enabled flag in the paca, and then checks whether
interrupts got hard-disabled. If so, it also sets the EE bit in the
MSR to hard-enable the interrupts.
This has the potential to improve performance, and also makes it
easier to make a kernel that can boot on iSeries and on other 64-bit
machines, since this lazy-disable strategy is very similar to the
soft-disable strategy that iSeries already uses.
This version renames paca->proc_enabled to paca->soft_enabled, and
changes a couple of soft-disables in the kexec code to hard-disables,
which should fix the crash that Michael Ellerman saw. This doesn't
yet use a reserved CR field for the soft_enabled and hard_enabled
flags. This applies on top of Stephen Rothwell's patches to make it
possible to build a combined iSeries/other kernel.
Signed-off-by: Paul Mackerras <paulus@samba.org>
During boot we bring up all memory and cpu nodes. Normally a PCI device
will be in one of these online nodes, however in some weird setups it
may not.
We have only seen this in the lab but we may as well check for the case
and fallback to -1 (all nodes).
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Instead of just checking that an address is in the right range, use the
provided __kernel_text_address() helper which covers both the kernel and
module text sections.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change ->num_pmcs to match the number of PMCs in POWER6.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At the moment we rely on a cpu feature bit or a firmware property to
detect altivec. If we dont have either of these and the cpu does in fact
support altivec we can cause a panic from userspace.
It seems safer to always send a signal if we manage to get an 0xf20
exception from userspace.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When update_bridge_base() updates the IO window on a PCI-to-PCI
bridge, it fails to zero the upper 16 bits of the base and limit
registers if the window size is less than 64K. This fixes it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add missing entry in Makefile for MPC832x MDS support. It
also change white space to tab in MPC8360 entry.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
MPC8360EMDS PB support is broken as some code was missing
in last submission. This patch adds missing code and makes
MPC8360EMDS PB support working.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In the timer_interrupt we were not calling set_irq_regs() and if we are
profiling we will end up calling get_irq_regs(). This causes bad things to
happen.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A find -iname \*.[ch] | xargs grep "> ARRAY_SIZE(" revealed several
incorrect usages of ARRAY_SIZE in the mpc drivers. The last element in the
array is always ARRAY_SIZE()-1, this patch modifies the bounds checks
accordingly.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Cc: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The default configuration file for the MPC8349E-mITX reference board,
mpc834x_itx_defconfig, did not include support for DOS partition table types.
This support is necessary because the hard drive that comes with the ITX
is formatted with this partition table type. Without this config option,
no partitions on the drive can be mounted.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a memory leak introduced by "spufs: add support
for read/write oncntl", which was missing a call to simple_attr_close.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The SPU code will crash if CONFIG_NUMA is not set and SPUs are found on
a non-0 node. This workaround will ignore those SPEs and just print an
message in the kernel log.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I need this patch to get a UML kernel to compile. This is with the
kernel headers in FC6 which are automatically generated from the kernel
tree. Some headers are missing but those files don't need them. At
least it appears so since the resuling kernel works fine.
Tested on x86-64.
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The Linux group at Stratus Technologies has come across an issue with SCI
routing under ACPI. We were bitten by this when we made an x86_64 platform
whose BIOS provides an Interrupt Source Override for the SCI itself.
Apparently the override has no effect for the System Control Interrupt, and
this appears to be because of the way the SCI is setup in the ACPI code.
It does not handle the case where busirq != gsi.
The code that sets up the SCI routing assumes that bus irq == global irq.
So there is simply no provision for telling it otherwise. The attached
patch provides this mechanism.
This patch provided by David Bulkow, was tested on an i386 platform, which
does not use the SCI override, and also on an x86_64 platform which does
use an override.
Signed-off-by: David Bulkow <david.bulkow@stratus.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Intel processors starting with the Core Duo support
support processor native C-state using the MWAIT instruction.
Refer: Intel Architecture Software Developer's Manual
http://www.intel.com/design/Pentium4/manuals/253668.htm
Platform firmware exports the support for Native C-state to OS using
ACPI _PDC and _CST methods.
Refer: Intel Processor Vendor-Specific ACPI: Interface Specification
http://www.intel.com/technology/iapc/acpi/downloads/302223.htm
With Processor Native C-state, we use 'MWAIT' instruction on the processor
to enter different C-states (C1, C2, C3). We won't use the special IO
ports to enter C-state and no SMM mode etc required to enter C-state.
Overall this will mean better C-state support.
One major advantage of using MWAIT for all C-states is, with this and
"treat interrupt as break event" feature of MWAIT, we can now get accurate
timing for the time spent in C1, C2, .. states.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Get rid of warning in the thermal throttling code about not checking
sysfs return values.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Apparently whoever converted voyager never actually checked that the
patch would compile ...
Remove as much of the pt_regs references as possible and move the
remaining ones into line with what's in x86 generic.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The implementation of genirq in x86 completely broke voyager (and
presumably visws). Since it's plugged into so much of the x86
infrastructure, you can't expect it to work unconverted.
This patch introduces a voyager IRQ handler type and switches voyager
to the genirq infrastructure.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Kernel build breaks with CONFIG_X86_VSMP. Probably due to some header
file cleanups in 2.6.19-rc1.
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes my one line thinko where I was clearing
the vector_irq entries on the wrong cpus.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix these 2.6.19-rc1 build warnings from modpost:
WARNING: vmlinux - Section mismatch: reference to .init.text:_sinittext from .text between 'core_kernel_text' (at offset 0x3e060) and '__kernel_text_address'
WARNING: vmlinux - Section mismatch: reference to .init.text:_sinittext from .text between 'core_kernel_text' (at offset 0x3e064) and '__kernel_text_address'
WARNING: vmlinux - Section mismatch: reference to .init.text:_einittext from .text between 'core_kernel_text' (at offset 0x3e07c) and '__kernel_text_address'
WARNING: vmlinux - Section mismatch: reference to .init.text:_einittext from .text between 'core_kernel_text' (at offset 0x3e080) and '__kernel_text_address'
WARNING: vmlinux - Section mismatch: reference to .init.text:_sinittext from .text between 'is_ksym_addr' (at offset 0x4b3a4) and 'kallsyms_expand_symbol'
WARNING: vmlinux - Section mismatch: reference to .init.text:_sinittext from .text between 'is_ksym_addr' (at offset 0x4b3a8) and 'kallsyms_expand_symbol'
WARNING: vmlinux - Section mismatch: reference to .init.text:_einittext from .text between 'is_ksym_addr' (at offset 0x4b3b4) and 'kallsyms_expand_symbol'
WARNING: vmlinux - Section mismatch: reference to .init.text:_einittext from .text between 'is_ksym_addr' (at offset 0x4b3e4) and 'kallsyms_expand_symbol'
WARNING: vmlinux - Section mismatch: reference to .init.text:_sinittext from .text between 'get_symbol_pos' (at offset 0x4b640) and 'kallsyms_lookup_size_offset'
WARNING: vmlinux - Section mismatch: reference to .init.text:_sinittext from .text between 'get_symbol_pos' (at offset 0x4b644) and 'kallsyms_lookup_size_offset'
WARNING: vmlinux - Section mismatch: reference to .init.text:_einittext from .text between 'get_symbol_pos' (at offset 0x4b654) and 'kallsyms_lookup_size_offset'
WARNING: vmlinux - Section mismatch: reference to .init.text:_einittext from .text between 'get_symbol_pos' (at offset 0x4b658) and 'kallsyms_lookup_size_offset'
WARNING: vmlinux - Section mismatch: reference to .init.text:_sinittext from .text between 'get_symbol_pos' (at offset 0x4b68c) and 'kallsyms_lookup_size_offset'
The crux of the matter is that modpost only checks the relocatable
sections. i386 vmlinux has none, so modpost does no checking on it (it
does on the modules). However, sparc vmlinux has plenty of
relocatable sections because it is being built with 'ld -r' (to allow
for btfixup processing). So for sparc, modpost does do a lot of
checking. Sure enough, running modpost on arch/sparc/boot/image yields
no output (i.e. all is well).
modpost.c check_sec_ref() has:
/* We want to process only relocation sections and not .init */
if (sechdrs[i].sh_type == SHT_RELA) {
// check here
} else if (sechdrs[i].sh_type == SHT_REL) {
// check here
}
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix this 2.6.19-rc1 build warnings from modpost:
WARNING: vmlinux - Section mismatch: reference to .init.text:sunzilog_console_setup from .data between 'sunzilog_console' (at offset 0x8394) and 'devices_subsys'
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix these 2.6.19-rc1 build warnings from modpost:
WARNING: vmlinux - Section mismatch: reference to .init.text:__alloc_bootmem from .text between 'srmmu_nocache_init' (at offset 0x1a0f8) and 'srmmu_mmu_info'
WARNING: vmlinux - Section mismatch: reference to .init.text:__alloc_bootmem from .text between 'srmmu_nocache_init' (at offset 0x1a118) and 'srmmu_mmu_info'
WARNING: vmlinux - Section mismatch: reference to .init.text:srmmu_early_allocate_ptable_skeleton from .text between 'srmmu_nocache_init' (at offset 0x1a188) and 'srmmu_mmu_info'
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kill off interrupt_table for all of the CPU subtypes, we now
default in to stepping in to do_IRQ() for _all_ IRQ exceptions
and counting the spurious ones, rather than simply flipping on
the ones we cared about. This and enabling the IRQ by default
automatically has already uncovered a couple of bugs and IRQs
that weren't being caught, as well as some that are being
generated far too often (SCI Tx Data Empty, for example).
The general rationale is to use a marker for interrupt exceptions,
test for it in the handle_exception() path, and skip out to
do_IRQ() if it's found. Everything else follows the same behaviour
of finding the cached EXPEVT value in r2/r2_bank, we just rip out
the INTEVT read from entry.S entirely (except for in the kGDB NMI
case, which is another matter).
Note that while this changes the do_IRQ() semantics regarding r4
handling, they were fundamentally broken anyways (relying entirely
on r2_bank for the cached code). With this, we do the INTEVT read
from do_IRQ() itself (in the CONFIG_CPU_HAS_INTEVT case), or fall
back on r4 for the muxed IRQ number, which should also be closer
to what SH-2 and SH-2A want anyways.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that we've started accounting for spurious IRQs, change the
logic somewhat so that we have a better chance of catching them.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Pass NULL not 0 for pointer value.
[MIPS] IP27: Make declaration of setup_replication_mask a proper prototype.
[MIPS] BigSur: More useful defconfig.
[MIPS] Cleanup definitions of speed_t and tcflag_t.
[MIPS] Fix compilation warnings in arch/mips/sibyte/bcm1480/smp.c
[MIPS] Optimize and cleanup get_saved_sp, set_saved_sp
[MIPS] <asm/irq.h> does not need pt_regs anymore.
[MIPS] Workaround for bug in gcc -EB / -EL options.
[MIPS] Fix timer setup for Jazz
Certain gcc versions upto gcc 4.1.1 (probably 4.2-subversion as of
2006-10-10 don't properly change the the predefined symbols if -EB / -EL
are used, so we kludge that here. A bug has been filed at
http://gcc.gnu.org/bugzilla/show_bug.cgi?id=29413.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
taken exports to actual definitions of symbols being exported.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sun3_ksyms gone, m68k_ksyms trimmed down to exports of the assembler ones,
for sun3 added the missing exports of __ioremap() and iounmap().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
