pci_get_device() decrements the reference count of "from" (last
argument) so when we break off the loop successfully we have only one
device reference - and we don't know which device we have. If we want
a reference to each device, we must take them explicitly and let
the pci_get_device() walk complete to avoid duplicate references.
This is serious, as over-putting device references will cause
the device to eventually disappear. Without this fix, the kernel
crashes after a few insmod/rmmod cycles.
Tested on an Intel S7000FC4UR system with a 7300 chipset.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Link: http://lkml.kernel.org/r/20140224111656.09bbb7ed@endymion.delvare
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: stable@vger.kernel.org
Signed-off-by: Borislav Petkov <bp@suse.de>
The reference count changes done by pci_get_device can be a little
misleading when the usage diverges from the most common scheme. The
reference count of the device passed as the last parameter is always
decreased, even if the function returns no new device. So if we are
going to try alternative device IDs, we must manually increment the
device reference count before each retry. If we don't, we end up
decreasing the reference count, and after a few modprobe/rmmod cycles
the PCI devices will vanish.
In other words and as Alan put it: without this fix the EDAC code
corrupts the PCI device list.
This fixes kernel bug #50491:
https://bugzilla.kernel.org/show_bug.cgi?id=50491
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Link: http://lkml.kernel.org/r/20140224093927.7659dd9d@endymion.delvare
Reviewed-by: Alan Cox <alan@linux.intel.com>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: stable@vger.kernel.org
Signed-off-by: Borislav Petkov <bp@suse.de>
HP Folio 13 may have a broken BIOS that doesn't set up the mute LED
GPIO properly, and the driver guesses it wrongly, too. Add a new
fixup entry for setting the GPIO pin statically for this laptop.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=70991
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The codec->control_data contains a pointer to the device's regmap struct. But
wm8994_bulk_write() expects a pointer to the parent wm8998 device.
The issue was introduced in commit d9a7666f ("ASoC: Remove ASoC-specific
WM8994 I/O code").
Fixes: d9a7666f ("ASoC: Remove ASoC-specific WM8994 I/O code")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
The D-Link DWA-123 REV D1 with USB ID 2001:3310 uses this driver.
Signed-off-by: Manu Gupta <manugupt1@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The virtio spec requires byte 0 of the virtio-scsi LUN structure
to be '1'.
Signed-off-by: Venkatesh Srinivas <venkateshs@google.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Releasing the touchscreen lets the internal statemachine left in a wrong state.
Due to this the release coordinate will be reported again by accident when the next
touchscreen event happens. This change sets up the correct state when waiting
for the next touchscreen event.
This has led to reported issues with calibrating the touchscreen.
Bug was introduced somewhere in the series that began with
18da755de5
Staging/iio/adc/touchscreen/MXS: add proper clock handling
in which the way this driver worked was substantially changed
to be interrupt driven rather than relying on a busy loop.
This was a regression in the 3.13 kernel.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
A selective retransmission request (SRR) is a fibre-channel
protocol control request which provides support for requesting
retransmission of a data sequence in response to an issue such as
frame loss or corruption. These events are experienced
infrequently in fibre-channel based networks which makes
it difficult to test and assess codepaths which handle these
events.
We were fortunate enough, for some definition of fortunate, to
have a metro-area single-mode SAN link which, at 10 GBPS
sustained load levels, would consistently generate SRR's in
a SCST based target implementation using our SCST/in-kernel
Qlogic target interface driver. In response to an SRR the
in-kernel Qlogic target driver immediately panics resulting
in a catastrophic storage failure for serviced initiators.
The culprit was a debug statement in the qla_target.c file which
does not verify that a pointer to the SCSI CDB is not null.
The unchecked pointer dereference results in the kernel panic
and resultant system failure.
The other two references to the SCSI CDB by the SRR handling code
use a ternary operator to verify a non-null pointer is being
acted on. This patch simply adds a similar test to the implicated
debug statement.
This patch is a candidate for any stable kernel being maintained
since it addresses a potentially catastrophic event with
minimal downside.
Signed-off-by: Dr. Greg Wettstein <greg@enjellic.com>
Cc: <stable@vger.kernel.org> #3.5+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
dm_pool_close_thin_device() must be called if dm_set_target_max_io_len()
fails in thin_ctr(). Otherwise __pool_destroy() will fail because the
pool will still have an open thin device:
device-mapper: thin metadata: attempt to close pmd when 1 device(s) are still open
device-mapper: thin: __pool_destroy: dm_pool_metadata_close() failed.
Also, must establish error code if failing thin_ctr() because the pool
is in fail_io mode.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Cc: stable@vger.kernel.org
Pull SELinux endianness fix from James Morris.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
SELinux: bigendian problems with filename trans rules
Pull s390 bug fixes from Martin Schwidefsky:
"A couple of s390 bug fixes. The PCI segment boundary issue is a nasty
one as it can lead to data corruption"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/cio: Fix missing subchannels after CHPID configure on
s390/pci/dma: use correct segment boundary size
s390/compat: fix sys_sched_getattr compat wrapper
s390/zcrypt: additional check to avoid overflow in msg-type 6 requests
Stephane reported that perf report and annotate failed to process data
using lots of (> 500) shared libraries. It was because of the limit on
number of open files (ulimit -n).
Currently when perf loads a DSO, it'll look for normal and dynamic
symbol tables. And if it fails to find out both tables, it'll iterate
all of possible symtab types. But many of them are useless since they
have no additional information and the problem is that it's not closing
those files even though they're not used. Fix it.
Reported-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: Cody P Schafer <cody@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1392859976-32760-2-git-send-email-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The TUI of perf report and top support annotation, but stdio and GTK
don't. So it should be checked before calling hist_entry__inc_addr_
samples() to avoid wasting resources that will never be used.
perf annotate need it regardless of UI and sort keys, so the check
of whether to allocate resources should be on the tools that have
annotate as an option in the TUI, 'report' and 'top', not on the
function called by all of them.
It caused perf annotate on ppc64 to produce zero output, since the
buckets were not being allocated.
Reported-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1392859976-32760-1-git-send-email-namhyung@kernel.org
[ Renamed (report,top)__needs_annotate() to ui__has_annotation() ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
- allow booting xtfpga on boards with new uBoot and >128MBytes memory;
- drop nonexistent GPIO32 support from fsf variant;
- don't select USE_GENERIC_SMP_HELPERS;
- enable common clock framework support, set up ethoc clock on xtfpga;
- wire up sched_setattr and sched_getattr syscalls.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XS4m
-----END PGP SIGNATURE-----
Merge tag 'xtensa-for-next-20140221-1' into for_next
Xtensa fixes for 3.14:
- allow booting xtfpga on boards with new uBoot and >128MBytes memory;
- drop nonexistent GPIO32 support from fsf variant;
- don't select USE_GENERIC_SMP_HELPERS;
- enable common clock framework support, set up ethoc clock on xtfpga;
- wire up sched_setattr and sched_getattr syscalls.
Signed-off-by: Chris Zankel <chris@zankel.net>
A collection of fixes for ARM platforms. Most are fixes for DTS files,
mostly from DT conversion on OMAP which is still finding a few issues here
and there.
There's a couple of small stale code removal patches that we usually
queue for the next release instead, but they seemed harmless enough to
bring in now.
Also, a fix for backlight on some PXA platforms, and a cache configuration
fix for Tegra, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJTCgAlAAoJEIwa5zzehBx3J8MP/jFJWHtLHSeSXeKTLEeBV18J
/M7OG5hKyI38mImPbdJmCHpcTfExTqWuIkvN+6e7QN5PU1V3YSy5XELPh9UIn7zU
u+Pmt1C4cG8GFEdf03LqaDc4vdtthKUHGUBxQjrA3ZFrR8XZlzAZrnLKU/HA1VF5
ynaj1cs4Vpf2CGXjM+2ATr5gVhjTs1yldTkG+lHL99JAlSJe7TD3mrANXBRXVVNC
2yHGEDpDJf8kkBRQZ91xGcVVFw2YWF1avUi3QQ5WltufI+Rtdu8g7ibhakK/nimU
AfZ3LidjjiTFIGfEi5/2FBim6Tsxpd6wLlchzA6ksPaQ6hk0EVzRPPNzlarmeRO8
IF5zUPGPXswBeQURXe+OcZIUI4PGS02tshlIUWFPaFM3mZY2djd8Df8Rg20isjOu
vUYGSL2UY0uLb8NS97scNS9ouGYDp8lV9pHIYlmf6f3Opv6vsw56rWggSsDQDAOk
wbA2COTtDXxo1tEgbrmevDiaCc8uCDTHKD+uwbxOMCTwLvHHsafRp85BgcCz1z0L
bOvTbqVhBPW6T47D1ED+ECBo12DbZwA8pth0JSRaf/Fbp6+aMFXp0/d7Hw+ggAxN
wgEFq/A0M6v+5Y9azo+GLkgqPdH+7twH6eqD8TRgcQdnZXWIuq9UtaNw9Qx4Uusr
fX9CS2l8ISXgopnRPZCI
=i7LS
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A collection of fixes for ARM platforms. Most are fixes for DTS
files, mostly from DT conversion on OMAP which is still finding a few
issues here and there.
There's a couple of small stale code removal patches that we usually
queue for the next release instead, but they seemed harmless enough to
bring in now.
Also, a fix for backlight on some PXA platforms, and a cache
configuration fix for Tegra, etc"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (25 commits)
MAINTAINERS: add additional ARM BCM281xx/BCM11xxx maintainer
ARM: tegra: only run PL310 init on systems with one
ARM: tegra: Add head numbers to display controllers
ARM: imx6: build pm-imx6q.c independently of CONFIG_PM
ARM: tegra: fix RTC0 alias for Cardhu
ARM: dove: dt: revert PMU interrupt controller node
Documentation: dt: OMAP: Update Overo/Tobi
ARM: dts: Add support for both OMAP35xx and OMAP36xx Overo/Tobi
ARM: dts: omap3-tobi: Use the correct vendor prefix
ARM: dts: omap3-tobi: Fix boot with OMAP36xx-based Overo
ARM: OMAP2+: Remove legacy macros for zoom platforms
ARM: OMAP2+: Remove MACH_NOKIA_N800
ARM: dts: N900: add missing compatible property
ARM: dts: N9/N950: fix boot hang with 3.14-rc1
ARM: OMAP1: nokia770: enable tahvo-usb
ARM: OMAP2+: gpmc: fix: DT ONENAND child nodes not probed when MTD_ONENAND is built as module
ARM: OMAP2+: gpmc: fix: DT NAND child nodes not probed when MTD_NAND is built as module
ARM: dts: omap3-gta04: Fix mmc1 properties.
ARM: dts: omap3-gta04: Fix 'aux' gpio key flags.
ARM: OMAP2+: add missing ARCH_HAS_OPP
...
Mostly unexciting driver fixes, plus one fix to lower the severity of
the log message when we don't use an optional regulator - the fixes for
ACPI system made this come up more often and it was correctly observed
that it was causing undue concern for users.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yvBG
-----END PGP SIGNATURE-----
Merge tag 'regulator-v3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"Mostly unexciting driver fixes, plus one fix to lower the severity of
the log message when we don't use an optional regulator - the fixes
for ACPI system made this come up more often and it was correctly
observed that it was causing undue concern for users"
* tag 'regulator-v3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: max14577: Fix invalid return value on DT parse success
regulator: core: Change dummy supplies error message to a warning
regulator: s5m8767: Add missing of_node_put
regulator: s5m8767: Use of_get_child_by_name
regulator: da9063: Bug fix when setting max voltage on LDOs 5-11
Because then this sg is passed to sbc_copy_prot which will
hit a protection fault in cases we have more than a single sg.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds the three missing DIF related sense codes within
transport_generic_request_failure(), which are required to ensure
that the correct ASC/ASQC is generated by the subsequent call to
transport_send_check_condition_and_sense().
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug in sbc_dif_copy_prot() where the updated addr
offset did not take into account the case where the associated
scatterlist had not been incremented.
This addresses the case where incoming protection scatterlists may
contain a length smaller than PAGE_SIZE across multiple entires,
when the target protection scatterlists are always being explicitly
filled up to PAGE_SIZE before adding another entry.
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch excludes reserved-marker byte-position from oobfree->length
calculation. Thus all bytes from oobfree->offset till end of OOB are free.
CC: <stable@vger.kernel.org> # 3.13.x+
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
1) In current implementation, ecclayout->oobfree->offset is calculated with
respect to ecclayout->eccpos[0] which is incorrect because ECC bytes may not
be stored contiguously in OOB.
So, this patch calculates ecclayout->oobfree->offset with respect to last
ECC byte-position 'eccpos[ecclayout->eccbytes-1]'.
2) ECC layout of some ecc-schemes expects reserved-markers at specific eccpos[]
which should not be over-written by any file-system metadata.
So this patch aligns oobfree->offset taking into account of such markers.
CC: <stable@vger.kernel.org> # 3.13.x+
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pull timer fix from Thomas Gleixner:
"Serialize the registration of a new sched_clock in the currently ARM
only generic sched_clock facilty to avoid sched_clock havoc"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched_clock: Prevent callers from seeing half-updated data
Pull x86 fixes from Thomas Gleixner:
- a bugfix which prevents a divide by 0 panic when the newly introduced
try_msr_calibrate_tsc() fails
- enablement of the Baytrail platform to utilize the newfangled msr
based calibration
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: tsc: Add missing Baytrail frequency to the table
x86, tsc: Fallback to normal calibration if fast MSR calibration fails
Pull irq fixes from Thomas Gleixner:
"Another four fixlets to tame the ARM orion irq chip"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: orion: Fix getting generic chip pointer.
irqchip: orion: clear stale interrupts in irq_startup
irqchip: orion: use handle_edge_irq on bridge irqs
irqchip: orion: clear bridge cause register on init
Here are a number of USB fixes for reported issues for 3.14-rc4
The majority of these are for USB gadget, phy, and musb driver issues.
And there's a few new device ids thrown in for good measure.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlMJLmIACgkQMUfUDdst+ylvXQCdGw8XA8m783daSRWNhjtSCZdP
oq8An1mSq7W4Tj82EO91ulB5C9Q7+W4c
=BixM
-----END PGP SIGNATURE-----
Merge tag 'usb-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of USB fixes for reported issues for 3.14-rc4
The majority of these are for USB gadget, phy, and musb driver issues.
And there's a few new device ids thrown in for good measure"
* tag 'usb-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: chipidea: need to mask when writting endptflush and endptprime
usb: musb: correct use of schedule_delayed_work()
usb: phy: msm: fix compilation errors when !CONFIG_PM_SLEEP
usb: gadget: fix NULL pointer dereference
usb: gadget: printer: using gadget_is_otg to check otg support at runtime
phy: let phy_provider_register be the last step in registering PHY
phy-core: Don't allow building phy-core as a module
phy-core: Don't propagate -ENOSUPP from phy_pm_runtime_get_sync to caller
phy-core: phy_get: Leave error logging to the caller
phy,phy-bcm-kona-usb2.c: Add dependency on HAS_IOMEM
usb: musb: correct use of schedule_delayed_work()
usb: musb: do not sleep in atomic context
USB: serial: option: blacklist interface 4 for Cinterion PHS8 and PXS8
USB: EHCI: add delay during suspend to prevent erroneous wakeups
usb: gadget: bcm63xx_udc: fix build failure on DMA channel code
usb: musb: do not sleep in atomic context
usb: gadget: s3c2410_udc: Fix build error
usb: musb: core: Fix remote-wakeup resume
usb: musb: host: Fix SuperSpeed hub enumeration
usb: musb: fix obex in g_nokia.ko causing kernel panic
Here is a single commit, a revert of a sysfs file change that ended up
breaking a userspace tool.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlMJLK0ACgkQMUfUDdst+ynREQCcCl2HBK30ux8vwP0+tLvyx3AJ
lQYAn1COffBg1KS22gYyhm0Yez2pUgN2
=ZmpJ
-----END PGP SIGNATURE-----
Merge tag 'tty-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY revert from Greg KH:
"Here is a single commit, a revert of a sysfs file change that ended up
breaking a userspace tool"
* tag 'tty-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "tty: Set correct tty name in 'active' sysfs attribute"
Here is a single android driver fix for 3.14-rc4 that fixes a reported
problem in the binder driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlMJLckACgkQMUfUDdst+ynaDwCfVtgwCfLL//Ck5rsI+dPcNoH4
A4IAnjukxtAABpGDXAezROVpPSvnchRZ
=zWji
-----END PGP SIGNATURE-----
Merge tag 'staging-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree fix from Greg KH:
"Here is a single android driver fix for 3.14-rc4 that fixes a reported
problem in the binder driver"
* tag 'staging-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: binder: Fix death notifications
Here is a single commit, to fix a reported problem in the mei driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlMJLO4ACgkQMUfUDdst+ylvewCgofUZto3Z7tZbbMD/yUn87zWK
wH8An2aPuyRWy5rLdbW3vw2gFBz9TXaJ
=2xyg
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fix from Greg KH:
"Here is a single commit, to fix a reported problem in the mei driver"
* tag 'char-misc-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mei: set client's read_cb to NULL when flow control fails
Add myself as an additional maintainer for the Broadcom mobile
SoCs.
Signed-off-by: Matt Porter <mporter@linaro.org>
Acked-by: Christian Daudt <bcm@fixthebug.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
A few fixes, all driver speccific ones. The DaVinci ones aren't as
clear as they should be from the subject lines on the commits but they
fix issues which will prevent correct operation in some use cases and
only affect that particular driver so are reasonably safe.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Kgdb
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.14-rc3' into asoc-linus
ASoC: Fixes for v3.14
A few fixes, all driver speccific ones. The DaVinci ones aren't as
clear as they should be from the subject lines on the commits but they
fix issues which will prevent correct operation in some use cases and
only affect that particular driver so are reasonably safe.
# gpg: Signature made Wed 19 Feb 2014 13:23:13 JST using RSA key ID 7EA229BD
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
codec->control_data contains a pointer to the regmap struct of the device, not
to the device private data. Use snd_soc_codec_get_drvdata() instead.
The issue was introduced in commit 29fdf4fbbe ("ASoC: sta32x: Convert to
regmap").
Fixes: 29fdf4fbbe (ASoC: sta32x: Convert to regmap)
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
This reverts commit d8a5dc3033.
This breaks plymouth installs, either because plymouth is using the file
"incorrectly" or because the patch is incorrect. Either way, this needs
to be reverted until it is all figured out.
Reported-by: Josh Boyer <jwboyer@fedoraproject.org>
Reported-by: Ray Strode <halfline@gmail.com>
Cc: Lennart Poettering <lennart@poettering.net>
Cc: Kay Sievers <kay@vrfy.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Werner Fink <werner@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull scheduler fixes from Ingo Molnar:
"Misc fixlets: a fair number of them resulting from the new
SCHED_DEADLINE code"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/deadline: Remove useless dl_nr_total
sched/deadline: Test for CPU's presence explicitly
sched: Add 'flags' argument to sched_{set,get}attr() syscalls
sched: Fix information leak in sys_sched_getattr()
sched,numa: add cond_resched to task_numa_work
sched/core: Make dl_b->lock IRQ safe
sched/core: Fix sched_rt_global_validate
sched/deadline: Fix overflow to handle period==0 and deadline!=0
sched/deadline: Fix bad accounting of nr_running
Pull xfs fixes from Dave Chinner:
"This is the first pull request I've had to do for you, so I'm still
sorting things out. The reason I'm sending this and not Ben should be
obvious from the first commit below - SGI has stepped down from the
XFS maintainership role. As such, I'd like to take another
opportunity to thank them for their many years of effort maintaining
XFS and supporting the XFS community that they developed from the
ground up.
So I haven't had time to work things like signed tags into my
workflows yet, so this is just a repo branch I'm asking you to pull
from. And yes, I named the branch -rc4 because I wanted the fixes in
rc4, not because the branch was for merging into -rc3. Probably not
right, either.
Anyway, I should have everything sorted out by the time the next merge
window comes around. If there's anything that you don't like in the
pull req, feel free to flame me unmercifully.
The changes are fixes for recent regressions and important thinkos in
verification code:
- a log vector buffer alignment issue on ia32
- timestamps on truncate got mangled
- primary superblock CRC validation fixes and error message
sanitisation"
* 'xfs-fixes-for-3.14-rc4' of git://oss.sgi.com/xfs/xfs:
xfs: limit superblock corruption errors to actual corruption
xfs: skip verification on initial "guess" superblock read
MAINTAINERS: SGI no longer maintaining XFS
xfs: xfs_sb_read_verify() doesn't flag bad crcs on primary sb
xfs: ensure correct log item buffer alignment
xfs: ensure correct timestamp updates from truncate
This fixes bug introduced in 667a6b7a (regulator: max14577: Add missing
of_node_put). The DTS parsing function returned number of matched
regulators as success status which then was compared against 0 in probe.
Result was a probe fail after successful parsing the DTS:
max14577-regulator: probe of max14577-regulator failed with error 2
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviwed-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This reverts commit c4a391b53a. Dave
Chinner <david@fromorbit.com> has reported the commit may cause some
inodes to be left out from sync(2). This is because we can call
redirty_tail() for some inode (which sets i_dirtied_when to current time)
after sync(2) has started or similarly requeue_inode() can set
i_dirtied_when to current time if writeback had to skip some pages. The
real problem is in the functions clobbering i_dirtied_when but fixing
that isn't trivial so revert is a safer choice for now.
CC: stable@vger.kernel.org # >= 3.13
Signed-off-by: Jan Kara <jack@suse.cz>
- orion:
- fixes for clearing bridge cause register, and clearing stale interrupts
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=r7Cd
-----END PGP SIGNATURE-----
Merge tag 'irqchip-mvebu-fixes-3.14' of git://git.infradead.org/linux-mvebu into irq/urgent
irqchip mvebu fixes for v3.14
- orion:
- fixes for clearing bridge cause register, and clearing stale interrupts
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
