[ Upstream commit 5e6038b88a5718910dd74b949946d9d9cee9a041 ]
TSO and TBS cannot co-exist and current implementation requires two
fixes:
1) stmmac_open() does not need to call stmmac_enable_tbs() because
the MAC is reset in stmmac_init_dma_engine() anyway.
2) Inside stmmac_hw_setup(), we should call stmmac_enable_tso() for
TX Q that is _not_ configured for TBS.
Fixes: 579a25a854 ("net: stmmac: Initial support for TBS")
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90b669d65d99a3ee6965275269967cdee4da106e ]
The number of lanes of devlink port should be correctly initialized
when registering the port, so that the input check when running
"devlink port split <port> count <N>" can pass.
Fixes: a21cf0a833 ("devlink: Add a new devlink port lanes attribute and pass to netlink")
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74c1f1366eb7714b8b211554f6c5cee315ff3fbc ]
Explicitly reject using pointers that are not virt_to_phys() friendly
as the source for SEV commands that are sent to the PSP. The PSP works
with physical addresses, and __pa()/virt_to_phys() will not return the
correct address in these cases, e.g. for a vmalloc'd pointer. At best,
the bogus address will cause the command to fail, and at worst lead to
system instability.
While it's unlikely that callers will deliberately use a bad pointer for
SEV buffers, a caller can easily use a vmalloc'd pointer unknowingly when
running with CONFIG_VMAP_STACK=y as it's not obvious that putting the
command buffers on the stack would be bad. The command buffers are
relative small and easily fit on the stack, and the APIs to do not
document that the incoming pointer must be a physically contiguous,
__pa() friendly pointer.
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Fixes: 200664d523 ("crypto: ccp: Add Secure Encrypted Virtualization (SEV) command support")
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210406224952.4177376-3-seanjc@google.com>
Reviewed-by: Brijesh Singh <brijesh.singh@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d83b8aa5207d81f9f6daec9888390f079cc5db3f ]
The bit-masks used for the TXERRCH and RXERRCH (tx and rx error channels)
are incorrect and always lead to a zero result. The mask values are
currently the incorrect post-right shifted values, fix this by setting
them to the currect values.
(I double checked these against the TMS320TCI6482 data sheet, section
5.30, page 127 to ensure I had the correct mask values for the TXERRCH
and RXERRCH fields in the MACSTATUS register).
Addresses-Coverity: ("Operands don't affect result")
Fixes: a6286ee630 ("net: Add TI DaVinci EMAC driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8432b8114957235f42e070a16118a7f750de9d39 ]
As reported by syzbot [1], there is a memory leak while closing the
socket. We partially solved this issue with commit ac03046ece
("vsock/virtio: free packets during the socket release"), but we
forgot to drain the RX queue when the socket is definitely closed by
the scheduled work.
To avoid future issues, let's use the new virtio_transport_remove_sock()
to drain the RX queue before removing the socket from the af_vsock lists
calling vsock_remove_sock().
[1] https://syzkaller.appspot.com/bug?extid=24452624fc4c571eedd9
Fixes: ac03046ece ("vsock/virtio: free packets during the socket release")
Reported-and-tested-by: syzbot+24452624fc4c571eedd9@syzkaller.appspotmail.com
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 172e269edfce34bac7c61c15551816bda4b0f140 ]
We're starting from a TXQ label, not a TXQ type, so
efx_channel_get_tx_queue() is inappropriate. This worked by chance,
because labels and types currently match on EF10, but we shouldn't
rely on that.
Fixes: 12804793b1 ("sfc: decouple TXQ type from label")
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cfd577acb769301b19c31361d45ae1f145318b7a ]
Currently when the call to usb_urb_ep_type_check fails (returning -EINVAL)
the error return path returns -ENOMEM via the exit label "error". Other
uses of the same error exit label set the err variable to -ENOMEM but this
is not being used. I believe the original intent was for the error exit
path to return the value in err rather than the hard coded -ENOMEM, so
return this rather than the hard coded -ENOMEM.
Addresses-Coverity: ("Unused value")
Fixes: 738d9edcfd ("ALSA: usb-audio: Add sanity checks for invalid EPs")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210420134719.381409-1-colin.king@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 783a11bf2400e5d5c42a943c3083dc0330751842 ]
When i40iw_hmc_sd_one fails, chunk is freed without the deletion of chunk
entry in the PBLE info list.
Fix it by adding the chunk entry to the PBLE info list only after
successful addition of SD in i40iw_hmc_sd_one.
This fixes a static checker warning reported here:
https://lore.kernel.org/linux-rdma/YHV4CFXzqTm23AOZ@mwanda/
Fixes: 9715830157 ("i40iw: add pble resource files")
Link: https://lore.kernel.org/r/20210416002104.323-1-shiraz.saleem@intel.com
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sindhu Devale <sindhu.devale@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a6684385928d00b29acac7658a5ae1f2a44494c ]
missing qpid increment leads to skipping few qpids while allocating QP.
This eventually leads to adapter running out of qpids after establishing
fewer connections than it actually supports.
Current patch increments the qpid correctly.
Fixes: cfdda9d764 ("RDMA/cxgb4: Add driver for Chelsio T4 RNIC")
Link: https://lore.kernel.org/r/20210415151422.9139-1-bharat@chelsio.com
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ad18ff6449cbd6beb26b53128ddf56d2685aa93 ]
Commit 38ec4944b593 ("gro: ensure frag0 meets IP header alignment")
did the right thing, but missed the fact that napi_gro_frags() logics
calls for skb_gro_reset_offset() *before* pulling Ethernet header
to the skb linear space.
That said, the introduced check for frag0 address being aligned to 4
always fails for it as Ethernet header is obviously 14 bytes long,
and in case with NET_IP_ALIGN its start is not aligned to 4.
Fix this by adding @nhoff argument to skb_gro_reset_offset() which
tells if an IP header is placed right at the start of frag0 or not.
This restores Fast GRO for napi_gro_frags() that became very slow
after the mentioned commit, and preserves the introduced check to
avoid silent unaligned accesses.
From v1 [0]:
- inline tiny skb_gro_reset_offset() to let the code be optimized
more efficively (esp. for the !NET_IP_ALIGN case) (Eric);
- pull in Reviewed-by from Eric.
[0] https://lore.kernel.org/netdev/20210418114200.5839-1-alobakin@pm.me
Fixes: 38ec4944b593 ("gro: ensure frag0 meets IP header alignment")
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d892d60941b00c86d2029c8a99db24ab4979673 ]
The former fix only papered over the actual problem: the
ethernet core expects the netdev .dev member to have the
proper DMA masks set, or there will be BUG_ON() triggered
in kernel/dma/mapping.c.
Fix this by simply copying dma_mask and dma_mask_coherent
from the parent device.
Fixes: e45d0fad4a ("net: ethernet: ixp4xx: Use parent dev for DMA pool")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83cd92b46484aa8f64cdc0bff8ac6940d1f78519 ]
When initializing the __param array with a one liner, if all args are
const, the initial array value will be placed in the rodata section but
because libbpf does not support relocation in the rodata section, any
pointer in this array will stay NULL.
Fixes: c09add2fbc ("tools/libbpf: Add bpf_iter support")
Signed-off-by: Florent Revest <revest@chromium.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210419155243.1632274-5-revest@chromium.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e16edc99d658cd41c60a44cc14d170697aa3271f ]
VMCI feature is not supported in conjunction with the vSphere Fault
Tolerance (FT) feature.
VMware Tools can repeatedly try to create a vsock connection. If FT is
enabled the kernel logs is flooded with the following messages:
qp_alloc_hypercall result = -20
Could not attach to queue pair with -20
"qp_alloc_hypercall result = -20" was hidden by commit e8266c4c3307
("VMCI: Stop log spew when qp allocation isn't possible"), but "Could
not attach to queue pair with -20" is still there flooding the log.
Since the error message can be useful in some cases, print it only once.
Fixes: d021c34405 ("VSOCK: Introduce VM Sockets")
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 783003f3bb8a565326e89d18bbd948ad8ffc816a ]
The nftables offload parser sets FLOW_DISSECTOR_KEY_BASIC .n_proto to the
ethertype field in the ethertype frame. However:
- FLOW_DISSECTOR_KEY_BASIC .n_proto field always stores either IPv4 or IPv6
ethertypes.
- FLOW_DISSECTOR_KEY_VLAN .vlan_tpid stores either the 802.1q and 802.1ad
ethertypes. Same as for FLOW_DISSECTOR_KEY_CVLAN.
This function adjusts the flow dissector to handle two scenarios:
1) FLOW_DISSECTOR_KEY_VLAN .vlan_tpid is set to 802.1q or 802.1ad.
Then, transfer:
- the .n_proto field to FLOW_DISSECTOR_KEY_VLAN .tpid.
- the original FLOW_DISSECTOR_KEY_VLAN .tpid to the
FLOW_DISSECTOR_KEY_CVLAN .tpid
- the original FLOW_DISSECTOR_KEY_CVLAN .tpid to the .n_proto field.
2) .n_proto is set to 802.1q or 802.1ad. Then, transfer:
- the .n_proto field to FLOW_DISSECTOR_KEY_VLAN .tpid.
- the original FLOW_DISSECTOR_KEY_VLAN .tpid to the .n_proto field.
Fixes: a82055af59 ("netfilter: nft_payload: add VLAN offload support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff4d90a89d3d4d9814e0a2696509a7d495be4163 ]
The flow dissector representation expects the VLAN id in host byteorder.
Add the NFT_OFFLOAD_F_NETWORK2HOST flag to swap the bytes from nft_cmp.
Fixes: a82055af59 ("netfilter: nft_payload: add VLAN offload support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8e083ee8e2a6c94c29733835adae8bf5b832748 ]
In mwl8k_probe_hw, hw->priv->txq is freed at the first time by
dma_free_coherent() in the call chain:
if(!priv->ap_fw)->mwl8k_init_txqs(hw)->mwl8k_txq_init(hw, i).
Then in err_free_queues of mwl8k_probe_hw, hw->priv->txq is freed
at the second time by mwl8k_txq_deinit(hw, i)->dma_free_coherent().
My patch set txq->txd to NULL after the first free to avoid the
double free.
Fixes: a66098daac ("mwl8k: Marvell TOPDOG wireless driver")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210402182627.4256-1-lyl2019@mail.ustc.edu.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3186b880447ad3cc9b6487fa626a71d64b831524 ]
The right flag is apdma_sync when apdma remove hand-shake signel.
Fixes: 05f6f7271a38 ("i2c: mediatek: Fix apdma and i2c hand-shake timeout")
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92dfb27240fea2776f61c5422472cb6defca7767 ]
While adding the invalid IRQ check after calling platform_get_irq(),
I managed to overlook that the driver has a complex error path in its
probe() method, thus a simple *return* couldn't be used. Use a proper
*goto* instead!
Fixes: e5b2e3e74201 ("i2c: sh7760: add IRQ check")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b0e2c4f6be3ec68bf807c84e985e81c21404cd1 ]
gcc complains about undefined behavior in calling snprintf()
with the same buffer as input and output:
drivers/net/wireless/ti/wl18xx/debugfs.c: In function 'diversity_num_of_packets_per_ant_read':
drivers/net/wireless/ti/wl18xx/../wlcore/debugfs.h:86:3: error: 'snprintf' argument 4 overlaps destination object 'buf' [-Werror=restrict]
86 | snprintf(buf, sizeof(buf), "%s[%d] = %d\n", \
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
87 | buf, i, stats->sub.name[i]); \
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ti/wl18xx/debugfs.c:24:2: note: in expansion of macro 'DEBUGFS_FWSTATS_FILE_ARRAY'
24 | DEBUGFS_FWSTATS_FILE_ARRAY(a, b, c, wl18xx_acx_statistics)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ti/wl18xx/debugfs.c:159:1: note: in expansion of macro 'WL18XX_DEBUGFS_FWSTATS_FILE_ARRAY'
159 | WL18XX_DEBUGFS_FWSTATS_FILE_ARRAY(diversity, num_of_packets_per_ant,
There are probably other ways of handling the debugfs file, without
using on-stack buffers, but a simple workaround here is to remember the
current position in the buffer and just keep printing in there.
Fixes: bcca1bbdd4 ("wlcore: add debugfs macro to help print fw statistics arrays")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210323125723.1961432-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18fb0bedb5fc2fddc057dbe48b7360a6ffda34b3 ]
The signal strength of 5G is quite low, so user can't connect to an AP far
away. New parameters with new format and its parser are updated by the commit
84d26fda52 ("rtlwifi: Update 8821ae new phy parameters and its parser."), but
some parameters are missing. Use this commit to update to the novel parameters
that use new format.
Fixes: 84d26fda52 ("rtlwifi: Update 8821ae new phy parameters and its parser")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210219052607.7323-1-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9e46d344e62a0d56fd86a8289db5bed8a57c92e ]
If the VM entry/exit controls for loading/saving MSR_EFER are either
not available (an older processor or explicitly disabled) or not
used (host and guest values are the same), reading GUEST_IA32_EFER
from the VMCS returns an inaccurate value.
Because of this, in dump_vmcs() don't use GUEST_IA32_EFER to decide
whether to print the PDPTRs - always do so if the fields exist.
Fixes: 4eb64dce8d ("KVM: x86: dump VMCS on invalid entry")
Signed-off-by: David Edmondson <david.edmondson@oracle.com>
Message-Id: <20210318120841.133123-2-david.edmondson@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c47f892d7aa62765bf0689073f75990b4517a4cf ]
Daniel reported that with Commit 4ca234a9cb ("powerpc/smp: Stop
updating cpu_core_mask") QEMU was unable to set single NUMA node SMP
topologies such as:
-smp 8,maxcpus=8,cores=2,threads=2,sockets=2
i.e he expected 2 sockets in one NUMA node.
The above commit helped to reduce boot time on Large Systems for
example 4096 vCPU single socket QEMU instance. PAPR is silent on
having more than one socket within a NUMA node.
cpu_core_mask and cpu_cpu_mask for any CPU would be same unless the
number of sockets is different from the number of NUMA nodes.
One option is to reintroduce cpu_core_mask but use a slightly
different method to arrive at the cpu_core_mask. Previously each CPU's
chip-id would be compared with all other CPU's chip-id to verify if
both the CPUs were related at the chip level. Now if a CPU 'A' is
found related / (unrelated) to another CPU 'B', all the thread
siblings of 'A' and thread siblings of 'B' are automatically marked as
related / (unrelated).
Also if a platform doesn't support ibm,chip-id property, i.e its
cpu_to_chip_id returns -1, cpu_core_map holds a copy of
cpu_cpu_mask().
Fixes: 4ca234a9cb ("powerpc/smp: Stop updating cpu_core_mask")
Reported-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Tested-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210415120934.232271-2-srikar@linux.vnet.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38d0b1c9cec71e6d0f3bddef0bbce41d05a3e796 ]
The pci_bus->bridge reference may no longer be valid after
pci_bus_remove() resulting in passing a bad value to device_unregister()
for the associated bridge device.
Store the host_bridge reference in a separate variable prior to
pci_bus_remove().
Fixes: 7340056567 ("powerpc/pci: Reorder pci bus/bridge unregistration during PHB removal")
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210211182435.47968-1-tyreld@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ecb9dc1581eebecaee56decac70e35365260866 ]
Mirror commit aeba3731b1 ("powerpc/pci: Fix IO space breakage after
of_pci_range_to_resource() change").
Most MIPS platforms do not define PCI_IOBASE, nor implement
pci_address_to_pio(). Moreover, IO_SPACE_LIMIT is 0xffff for most MIPS
platforms. of_pci_range_to_resource passes the _start address_ of the IO
range into pci_address_to_pio, which then checks it against
IO_SPACE_LIMIT and fails, because for MIPS platforms that use
pci-legacy (pci-lantiq, pci-rt3883, pci-mt7620), IO ranges start much
higher than 0xffff.
In fact, pci-mt7621 in staging already works around this problem, see
commit 09dd629eea ("staging: mt7621-pci: fix io space and properly set
resource limits")
So just stop using of_pci_range_to_resource, which does not work for
MIPS.
Fixes PCI errors like:
pci_bus 0000:00: root bus resource [io 0xffffffff]
Fixes: 0b0b0893d4 ("of/pci: Fix the conversion of IO ranges into IO resources")
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbdfe5aaef3c1d5c5e62fa235ef13f064e4c1c17 ]
We should return -EINVAL instead of success if the "limit" is too high.
Fixes: e098bc9612 ("drm/amd/pm: optimize the power related source code layout")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 329328ec6a87f2c1275f50d979d55513de458409 ]
The intel_gvt_init_vgpu_type_groups() function is only called from
intel_gvt_init_device(). If it fails then the intel_gvt_init_device()
prints the error code and propagates it back again. That's a bug
because false is zero/success. The fix is to modify it to return zero
or negative error codes and make everything consistent.
Fixes: c5d71cb317 ("drm/i915/gvt: Move vGPU type related code into gvt file")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/YHaFQtk/DIVYK1u5@mwanda
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94f633ea8ade8418634d152ad0931133338226f6 ]
af_packet fanout uses RCU rules to ensure f->arr elements
are not dismantled before RCU grace period.
However, it lacks rcu accessors to make sure KCSAN and other tools
wont detect data races. Stupid compilers could also play games.
Fixes: dc99f60069 ("packet: Add fanout support.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: "Gong, Sishuai" <sishuai@purdue.edu>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c661b0b85444e426d3f23250305eeb16f6ffe88 ]
One use case of PACKET_FANOUT is lockless reception with one socket
per CPU. 256 is a practical limit on increasingly many machines.
Increase PACKET_FANOUT_MAX to 64K. Expand setsockopt PACKET_FANOUT to
take an extra argument max_num_members. Also explicitly define a
fanout_args struct, instead of implicitly casting to an integer. This
documents the API and simplifies the control flow.
If max_num_members is not specified or is set to 0, then 256 is used,
same as before.
Signed-off-by: Tanner Love <tannerlove@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 82c3ba31c370b6001cbf90689e98da1fb6f26aef ]
The bit-wise and of the action field with MLX5_ACCEL_ESP_ACTION_DECRYPT
is incorrect as MLX5_ACCEL_ESP_ACTION_DECRYPT is zero and not intended
to be a bit-flag. Fix this by using the == operator as was originally
intended.
Addresses-Coverity: ("Logically dead code")
Fixes: 7dfee4b1d7 ("net/mlx5: IPsec, Refactor SA handle creation and destruction")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b93bbc977af55fd10687f2c96c807cba95cb927 ]
Reset (aka power off) happens when the reset gpio is made active.
The reset gpio is GPIO_ACTIVE_LOW
Fixes: 9208847774 ("ASoC: ak5558: Add support for AK5558 ADC driver")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1618382024-31725-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33e4bc5946432a4ac173fd08e8e30a13ab94d06d ]
When under xmon, the "dxi" command dumps the state of the XIVE
interrupts. If an interrupt number is specified, only the state of
the associated XIVE interrupt is dumped. This form of the command
lacks an irq_data parameter which is nevertheless used by
xmon_xive_get_irq_config(), leading to an xmon crash.
Fix that by doing a lookup in the system IRQ mapping to query the IRQ
descriptor data. Invalid interrupt numbers, or not belonging to the
XIVE IRQ domain, OPAL event interrupt number for instance, should be
caught by the previous query done at the firmware level.
Fixes: 97ef275077 ("powerpc/xive: Fix xmon support on the PowerNV platform")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210331144514.892250-8-clg@kaod.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5b2e3e742015dd2aa6bc7bcef2cb59b2de1221c ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_irq() with invalid
IRQ #s.
Fixes: a26c20b1fa ("i2c: Renesas SH7760 I2C master driver")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 147178cf03a6dcb337e703d4dacd008683022a58 ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_irq() with the
invalid IRQ #s.
Fixes: 6ccbe60713 ("i2c: add Renesas R-Car I2C driver")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c975c432bc0aa53a90438fc80b369cb35134a48 ]
V3U creates spurious interrupts which we need to handle. This costs time
until BUS_PHASE_DATA can be activated which is problematic for Gen2 SoCs
and earlier. Because of this we introduce two interrupt handlers here
which will call a generic main irq function once the timing critical
stuff is done.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24c6d4bc563881539d2cd4433e502436ad87d512 ]
Ensure this irq runs as fast as possible.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d3bf53e897dce943b98d975bbde77156af6cd81 ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_irq() with invalid
IRQ #s.
Fixes: b5b5b32081 ("i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5e5f7a8d931fb4beba245bdbc94734175fda9de ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_irq() with invalid
IRQ #s.
Fixes: ba92222ed6 ("i2c: jz4780: Add i2c bus controller driver for Ingenic JZ4780")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb6129c32867baa7988f7fd2066cf18ed662d240 ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_irq() with invalid
IRQ #s.
Fixes: 5faf6e1f58 ("i2c: emev2: add driver")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5581c2c5d02bc63a0edb53e061c8e97cd490646e ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_irq() with invalid
IRQ #s.
Fixes: df8eb5691c ("i2c: Add driver for Cadence I2C controller")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a85c5c7a3aa8041777ff691400b4046e56149fd3 ]
The PM reference count is not expected to be incremented on
return in xiic_xfer and xiic_i2c_remove.
However, pm_runtime_get_sync will increment the PM reference
count even failed. Forgetting to putting operation will result
in a reference leak here.
Replace it with pm_runtime_resume_and_get to keep usage
counter balanced.
Fixes: 10b17004a7 ("i2c: xiic: Fix the clocking across bind unbind")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c662660ce2bd3b09dae21a9a9ac9395e1e6c00b ]
The PM reference count is not expected to be incremented on
return in these stm32f7_i2c_xx serious functions.
However, pm_runtime_get_sync will increment the PM reference
count even failed. Forgetting to putting operation will result
in a reference leak here.
Replace it with pm_runtime_resume_and_get to keep usage
counter balanced.
Fixes: ea6dd25dee ("i2c: stm32f7: add PM_SLEEP suspend/resume support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a4f326463117cee3adcb72999ca34a9aaafda93 ]
The PM reference count is not expected to be incremented on
return in sprd_i2c_master_xfer() and sprd_i2c_remove().
However, pm_runtime_get_sync will increment the PM reference
count even failed. Forgetting to putting operation will result
in a reference leak here.
Replace it with pm_runtime_resume_and_get to keep usage
counter balanced.
Fixes: 8b9ec07198 ("i2c: Add Spreadtrum I2C controller driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 780f629741257ed6c54bd3eb53b57f648eabf200 ]
The PM reference count is not expected to be incremented on
return in omap_i2c_probe() and omap_i2c_remove().
However, pm_runtime_get_sync will increment the PM reference
count even failed. Forgetting to putting operation will result
in a reference leak here. I Replace it with pm_runtime_resume_and_get
to keep usage counter balanced.
What's more, error path 'err_free_mem' seems not like a proper
name any more. So I change the name to err_disable_pm and move
pm_runtime_disable below, for pm_runtime of 'pdev->dev' should
be disabled when pm_runtime_resume_and_get fails.
Fixes: 3b0fb97c8d ("I2C: OMAP: Handle error check for pm runtime")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47ff617217ca6a13194fcb35c6c3a0c57c080693 ]
In i2c_imx_xfer() and i2c_imx_remove(), the pm reference count
is not expected to be incremented on return.
However, pm_runtime_get_sync will increment pm reference count
even failed. Forgetting to putting operation will result in a
reference leak here.
Replace it with pm_runtime_resume_and_get to keep usage
counter balanced.
Fixes: 3a5ee18d2a ("i2c: imx: implement master_xfer_atomic callback")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
