This is to fix the SPI DMA transfer failure for speed less than 1M.
If using current DMA burst size setting (16), the Rx data bytes are
invalid due to each data byte is multiplied according to the burst
size setting.
Let's said supposedly we shall receive the following 18 bytes of data:
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18
Instead, the data bytes received consist of "16 bytes of '01' +
2 bytes of '02'" :
01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 02 02
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Extract the common parts of rspi_transfer_one(), rspi_rz_transfer_one(),
and qspi_transfer_out_in() into the new function rspi_common_transfer().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Enable DMA support for RSPI on r7s72100 (RZ/A1H).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Enable DMA support for QSPI on R-Car Gen2, for Single, Dual, and Quad SPI
Transfers.
Performance figures for reading from a QSPI FLASH driven at 24.375 MHz
on r8a7791/koelsch:
- Single: 1.1 Mbps PIO, 23 Mbps DMA
- Dual : 12.7 Mbps PIO, 48 Mbps DMA
- Quad : 13 Mbps PIO, 70 Mbps DMA
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
rspi_send_dma() and rspi_send_receive_dma() are very similar. Consolidate
into a single function rspi_dma_transfer(), and add missing checks for
dmaengine_submit() failures.
Both sg_table pointer parameters can be NULL, as RSPI supports TX-only
mode, and unidirectional DMA transfers will also be needed later for
Dual/Quad DMA support.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
The DMA routines only need access to the scatter-gather tables inside the
spi_transfer structures, hence just pass those.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Refactor RSPI (on SH) DMA handling to make it reusable for other RSPI
implementations:
- Call the DMA routines after configuring the TX Mode bit and after
calling rspi_receive_init(), so these RSPI-specific operations can be
removed from the DMA routines,
- Absorb rspi_transfer_out_in() into rspi_transfer_one().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use the SPI core DMA mapping framework instead of our own.
If available, DMA is used for transfers larger than the FIFO size
(8 or 32 bytes).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
The SPI DMA core framework needs both RX and TX DMA to function. As a
preparation for converting the driver to use this framework, fall back to
PIO if no DMA channel or only one DMA channel is available.
This affects only RSPI, which could do DMA transfers for TX-only before.
RSPI-RZ and QSPI (at least for Single SPI Transfers) will need both RX and
TX DMA anyway.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
The resource is know to exist, as rspi_probe() already mapped it.
Remove the test, and just pass the resource.
Pass the device pointer instead of the platform device pointer, as the
latter is no longer needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Setup of the receive and transmit DMA channels is very similar, so let's
consolidate.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fall back to PIO if DMA configuration failed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
The various PIO loops are very similar. Consolidate into a single
function rspi_pio_transfer().
Both buffer pointers can be NULL, as RSPI supports TX-only mode, and
Dual/Quad SPI Transfers are unidirectional.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
RSPI needs dummy transfers to generate the SPI clock on receive.
RSPI-RZ and QSPI always do both transmit and receive.
Use the SPI core SPI_MASTER_MUST_RX/SPI_MASTER_MUST_TX infrastructure
instead of checking for the presence of buffers and providing dummy data
ourselves (for PIO), or providing a dummy buffer (for DMA).
rspi_receive_dma() now provides full duplex DMA transfers on RSPI, and is
renamed to rspi_send_receive_dma().
As the SPI core will always provide a TX buffer, the logic to choose
between DMA send and DMA send/receive in rspi_transfer_one() now has to
check for the presence of an RX buffer. Likewise for the DMA availability
tests in rspi_is_dma().
The buffer tests in qspi_transfer_one() are now always true, so they're
removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
The 16-bit DMA support doesn't fit well within the SPI core DMA framework,
as it needs to manage its own double-sized temporary buffers, for handling
the interleaved data.
Remove it, as there is no in-tree board code that sets
rspi_plat_data.dma_width_16bit.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit 8449fd76de ("spi: rspi: Merge
rspi_send_pio() and rspi_receive_pio()"), rspi_receive_init() is called
for transmit-only transfers too, while this is not needed.
Only call rspi_receive_init() when receiving, to preserve behavior on
RSPI on SH.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Pull powerpc fix from Ben Herrenschmidt:
"Here's just one trivial patch to wire up sys_renameat2 which I seem to
have completely missed so far.
(My test build scripts fwd me warnings but miss the ones generated for
missing syscalls)"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Wire renameat2() syscall
Pull MIPS fixes from Ralf Baechle:
"A fair number of fixes across the field. Nothing terribly
complicated; the one liners in below changelog should be fairly
descriptive.
Noteworthy is the SB1 change which the result of changes to binutils
resulting in one big gas warning for most files being assembled as
well as the asid_cache and branch emulation fixes which fix corruption
or possible uninteded behaviour of kernel or application code. The
remainder of fixes are more platforms or subsystem specific"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: R46000: Fix Micro-assembler field overflow for R4600 V2
MIPS: ptrace: Avoid smp_processor_id() in preemptible code
MIPS: Lemote 2F: cs5536: mfgpt: use raw locks
MIPS: SB1: Fix excessive kernel warnings.
MIPS: RC32434: fix broken PCI resource initialization
MIPS: malta: memory.c: Initialize the 'memsize' variable
MIPS: Fix typo when reporting cache and ftlb errors for ImgTec cores
MIPS: Fix inconsistancy of __NR_Linux_syscalls value
MIPS: Fix branch emulation of branch likely instructions.
MIPS: Fix a typo error in AUDIT_ARCH definition
MIPS: Change type of asid_cache to unsigned long
Pull scheduler fixes from Ingo Molnar:
"Various fixlets, mostly related to the (root-only) SCHED_DEADLINE
policy, but also a hotplug bug fix and a fix for a NR_CPUS related
overallocation bug causing a suspend/resume regression"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Fix hotplug vs. set_cpus_allowed_ptr()
sched/cpupri: Replace NR_CPUS arrays
sched/deadline: Replace NR_CPUS arrays
sched/deadline: Restrict user params max value to 2^63 ns
sched/deadline: Change sched_getparam() behaviour vs SCHED_DEADLINE
sched: Disallow sched_attr::sched_policy < 0
sched: Make sched_setattr() correctly return -EFBIG
In commit 7dd6278733 (spi/pxa2xx: Convert
to core runtime PM) master->auto_runtime_pm was set to true.
In this case pm_runtime_enable() must be called *before*
spi_register_master(), otherwise the kernel hangs with this error
message:
spi_master spi0: Failed to power device: -13
A similar fix, but for spi/hspi, was applied in
268d76430d.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Mark Brown <broonie@linaro.org>
Pull core futex/rtmutex fixes from Thomas Gleixner:
"Three fixlets for long standing issues in the futex/rtmutex code
unearthed by Dave Jones syscall fuzzer:
- Add missing early deadlock detection checks in the futex code
- Prevent user space from attaching a futex to kernel threads
- Make the deadlock detector of rtmutex work again
Looks large, but is more comments than code change"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rtmutex: Fix deadlock detector for real
futex: Prevent attaching to kernel threads
futex: Add another early deadlock detection check
Pull drm fixes from Dave Airlie:
"Mostly quiet now:
i915:
fixing userspace visiblie issues, all stable marked
radeon:
one more pll fix, two crashers, one suspend/resume regression"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: Resume fbcon last
drm/radeon: only allocate necessary size for vm bo list
drm/radeon: don't allow RADEON_GEM_DOMAIN_CPU for command submission
drm/radeon: avoid crash if VM command submission isn't available
drm/radeon: lower the ref * post PLL maximum once more
drm/i915: Prevent negative relocation deltas from wrapping
drm/i915: Only copy back the modified fields to userspace from execbuffer
drm/i915: Fix dynamic allocation of physical handles
lock_parent() very much on purpose does nested locking of dentries, and
is careful to maintain the right order (lock parent first). But because
it didn't annotate the nested locking order, lockdep thought it might be
a deadlock on d_lock, and complained.
Add the proper annotation for the inner locking of the child dentry to
make lockdep happy.
Introduced by commit 046b961b45 ("shrink_dentry_list(): take parent's
->d_lock earlier").
Reported-and-tested-by: Josh Boyer <jwboyer@fedoraproject.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
So a few people complained that
commit 177cf92de4
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Apr 1 22:14:59 2014 +0200
drm/crtc-helpers: fix dpms on logic
which was merged into 3.15-rc1, broke resume on radeons. Strangely git
bisect lead everyone to
commit 25f397a429
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Jul 19 18:57:11 2013 +0200
drm/crtc-helper: explicit DPMS on after modeset
which was merged long ago and actually part of 3.14.
Digging deeper I've noticed (again) that the call to
drm_helper_resume_force_mode in the radeon resume handlers was a no-op
previously because everything gets shut down on suspend. radeon does
this with explicit calls to drm_helper_connector_dpms with DPMS_OFF.
But with 177c we now force the dpms state to ON, so suddenly
resume_force_mode actually forced the crtcs back on.
This is the intention of the change after all, the problem is that
radeon resumes the fbdev console layer _before_ restoring the display,
through calling fb_set_suspend. And fbcon does an immediate ->set_par,
which in turn causes the same forced mode restore to happen.
Two concurrent modeset operations didn't lead to happiness. Fix this
by delaying the fbcon resume until the end of the readeon resum
functions.
v2: Fix up a bit of the spelling fail.
References: https://lkml.org/lkml/2014/5/29/1043
References: https://lkml.org/lkml/2014/5/2/388
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=74751
Tested-by: Ken Moffat <zarniwhoop@ntlworld.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Ken Moffat <zarniwhoop@ntlworld.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@gmail.com>
this is the next pull request for stashed up radeon fixes for 3.15. This is finally calming down with only four patches in this pull request.
* 'drm-fixes-3.15' of git://people.freedesktop.org/~deathsimple/linux:
drm/radeon: only allocate necessary size for vm bo list
drm/radeon: don't allow RADEON_GEM_DOMAIN_CPU for command submission
drm/radeon: avoid crash if VM command submission isn't available
drm/radeon: lower the ref * post PLL maximum once more
Pull input subsystem fixes from Dmitry Torokhov:
"A couple of driver/build fixups and also redone quirk for Synaptics
touchpads on Lenovo boxes (now using PNP IDs instead of DMI data to
limit number of quirks)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics - change min/max quirk table to pnp-id matching
Input: synaptics - add a matches_pnp_id helper function
Input: synaptics - T540p - unify with other LEN0034 models
Input: synaptics - add min/max quirk for the ThinkPad W540
Input: ambakmi - request a shared interrupt for AMBA KMI devices
Input: pxa27x-keypad - fix generating scancode
Input: atmel-wm97xx - only build for AVR32
Input: fix ps2/serio module dependency
because dm-cache cannot yet handle discards that span cache blocks.
Really fix a dm-mpath LOCKDEP warning that was introduced in -rc1.
Add a 'no_space_timeout' control to dm-thinp to restore the ability to
queue IO indefinitely when no data space is available. This fixes a
change in behavior that was introduced in -rc6 where the timeout
couldn't be disabled.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTh9QAAAoJEMUj8QotnQNaNpYH/j07FeH8YlxXRcFzDi7xRVtx
luK5b9fLLlmPwW2eKSrvpI8Le4jwDvLwBmpEvN9/wyPiRDSUnYIyYdoV7RJXX2LT
wqXatObb84fwQBJ6/q8o2YMzU5ODa5XT6KGEZyD4cHdAZ9FZSwfgqhslyrBJDkSN
JBFfkXu066qw8cuYA6KFv4DwBf5eHAt5AjV/QPGd5zGXwETHLZ4ypgpwYHAGbdXa
MgfHetwtEnJYvVQex/e+9xC5IDc4/BEAhZq4n3YmEJjNq8EbX15udHmCX7S2M5pT
+9tNjUMz4j9BhoC9F8ntRz0pxWZtJK9hGojO4xoXqOCOHgp1xLQd/tHrFZS0v8E=
=u5Xd
-----END PGP SIGNATURE-----
Merge tag 'dm-3.15-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device-mapper fixes from Mike Snitzer:
"A dm-cache stable fix to split discards on cache block boundaries
because dm-cache cannot yet handle discards that span cache blocks.
Really fix a dm-mpath LOCKDEP warning that was introduced in -rc1.
Add a 'no_space_timeout' control to dm-thinp to restore the ability to
queue IO indefinitely when no data space is available. This fixes a
change in behavior that was introduced in -rc6 where the timeout
couldn't be disabled"
* tag 'dm-3.15-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm mpath: really fix lockdep warning
dm cache: always split discards on cache block boundaries
dm thin: add 'no_space_timeout' dm-thin-pool module param
While I play inhouse patches with much memory pressure on qemu-kvm,
3.14 kernel was randomly crashed. The reason was kernel stack overflow.
When I investigated the problem, the callstack was a little bit deeper
by involve with reclaim functions but not direct reclaim path.
I tried to diet stack size of some functions related with alloc/reclaim
so did a hundred of byte but overflow was't disappeard so that I encounter
overflow by another deeper callstack on reclaim/allocator path.
Of course, we might sweep every sites we have found for reducing
stack usage but I'm not sure how long it saves the world(surely,
lots of developer start to add nice features which will use stack
agains) and if we consider another more complex feature in I/O layer
and/or reclaim path, it might be better to increase stack size(
meanwhile, stack usage on 64bit machine was doubled compared to 32bit
while it have sticked to 8K. Hmm, it's not a fair to me and arm64
already expaned to 16K. )
So, my stupid idea is just let's expand stack size and keep an eye
toward stack consumption on each kernel functions via stacktrace of ftrace.
For example, we can have a bar like that each funcion shouldn't exceed 200K
and emit the warning when some function consumes more in runtime.
Of course, it could make false positive but at least, it could make a
chance to think over it.
I guess this topic was discussed several time so there might be
strong reason not to increase kernel stack size on x86_64, for me not
knowing so Ccing x86_64 maintainers, other MM guys and virtio
maintainers.
Here's an example call trace using up the kernel stack:
Depth Size Location (51 entries)
----- ---- --------
0) 7696 16 lookup_address
1) 7680 16 _lookup_address_cpa.isra.3
2) 7664 24 __change_page_attr_set_clr
3) 7640 392 kernel_map_pages
4) 7248 256 get_page_from_freelist
5) 6992 352 __alloc_pages_nodemask
6) 6640 8 alloc_pages_current
7) 6632 168 new_slab
8) 6464 8 __slab_alloc
9) 6456 80 __kmalloc
10) 6376 376 vring_add_indirect
11) 6000 144 virtqueue_add_sgs
12) 5856 288 __virtblk_add_req
13) 5568 96 virtio_queue_rq
14) 5472 128 __blk_mq_run_hw_queue
15) 5344 16 blk_mq_run_hw_queue
16) 5328 96 blk_mq_insert_requests
17) 5232 112 blk_mq_flush_plug_list
18) 5120 112 blk_flush_plug_list
19) 5008 64 io_schedule_timeout
20) 4944 128 mempool_alloc
21) 4816 96 bio_alloc_bioset
22) 4720 48 get_swap_bio
23) 4672 160 __swap_writepage
24) 4512 32 swap_writepage
25) 4480 320 shrink_page_list
26) 4160 208 shrink_inactive_list
27) 3952 304 shrink_lruvec
28) 3648 80 shrink_zone
29) 3568 128 do_try_to_free_pages
30) 3440 208 try_to_free_pages
31) 3232 352 __alloc_pages_nodemask
32) 2880 8 alloc_pages_current
33) 2872 200 __page_cache_alloc
34) 2672 80 find_or_create_page
35) 2592 80 ext4_mb_load_buddy
36) 2512 176 ext4_mb_regular_allocator
37) 2336 128 ext4_mb_new_blocks
38) 2208 256 ext4_ext_map_blocks
39) 1952 160 ext4_map_blocks
40) 1792 384 ext4_writepages
41) 1408 16 do_writepages
42) 1392 96 __writeback_single_inode
43) 1296 176 writeback_sb_inodes
44) 1120 80 __writeback_inodes_wb
45) 1040 160 wb_writeback
46) 880 208 bdi_writeback_workfn
47) 672 144 process_one_work
48) 528 112 worker_thread
49) 416 240 kthread
50) 176 176 ret_from_fork
[ Note: the problem is exacerbated by certain gcc versions that seem to
generate much bigger stack frames due to apparently bad coalescing of
temporaries and generating too many spills. Rusty saw gcc-4.6.4 using
35% more stack on the virtio path than 4.8.2 does, for example.
Minchan not only uses such a bad gcc version (4.6.3 in his case), but
some of the stack use is due to debugging (CONFIG_DEBUG_PAGEALLOC is
what causes that kernel_map_pages() frame, for example). But we're
clearly getting too close.
The VM code also seems to have excessive stack frames partly for the
same compiler reason, triggered by excessive inlining and lots of
function arguments.
We need to improve on our stack use, but in the meantime let's do this
simple stack increase too. Unlike most earlier reports, there is
nothing simple that stands out as being really horribly wrong here,
apart from the fact that the stack frames are just bigger than they
should need to be. - Linus ]
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S Tsirkin <mst@redhat.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: PJ Waskiewicz <pjwaskiewicz@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull vfs dcache livelock fix from Al Viro:
"Fixes for livelocks in shrink_dentry_list() introduced by fixes to
shrink list corruption; the root cause was that trylock of parent's
->d_lock could be disrupted by d_walk() happening on other CPUs,
resulting in shrink_dentry_list() making no progress *and* the same
d_walk() being called again and again for as long as
shrink_dentry_list() doesn't get past that mess.
The solution is to have shrink_dentry_list() treat that trylock
failure not as 'try to do the same thing again', but 'lock them in the
right order'"
* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
dentry_kill() doesn't need the second argument now
dealing with the rest of shrink_dentry_list() livelock
shrink_dentry_list(): take parent's ->d_lock earlier
expand dentry_kill(dentry, 0) in shrink_dentry_list()
split dentry_kill()
lift the "already marked killed" case into shrink_dentry_list()
We have the same problem with ->d_lock order in the inner loop, where
we are dropping references to ancestors. Same solution, basically -
instead of using dentry_kill() we use lock_parent() (introduced in the
previous commit) to get that lock in a safe way, recheck ->d_count
(in case if lock_parent() has ended up dropping and retaking ->d_lock
and somebody managed to grab a reference during that window), trylock
the inode->i_lock and use __dentry_kill() to do the rest.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The cause of livelocks there is that we are taking ->d_lock on
dentry and its parent in the wrong order, forcing us to use
trylock on the parent's one. d_walk() takes them in the right
order, and unfortunately it's not hard to create a situation
when shrink_dentry_list() can't make progress since trylock
keeps failing, and shrink_dcache_parent() or check_submounts_and_drop()
keeps calling d_walk() disrupting the very shrink_dentry_list() it's
waiting for.
Solution is straightforward - if that trylock fails, let's unlock
the dentry itself and take locks in the right order. We need to
stabilize ->d_parent without holding ->d_lock, but that's doable
using RCU. And we'd better do that in the very beginning of the
loop in shrink_dentry_list(), since the checks on refcount, etc.
would need to be redone anyway.
That deals with a half of the problem - killing dentries on the
shrink list itself. Another one (dropping their parents) is
in the next commit.
locking parent is interesting - it would be easy to do rcu_read_lock(),
lock whatever we think is a parent, lock dentry itself and check
if the parent is still the right one. Except that we need to check
that *before* locking the dentry, or we are risking taking ->d_lock
out of order. Fortunately, once the D1 is locked, we can check if
D2->d_parent is equal to D1 without the need to lock D2; D2->d_parent
can start or stop pointing to D1 only under D1->d_lock, so taking
D1->d_lock is enough. In other words, the right solution is
rcu_read_lock/lock what looks like parent right now/check if it's
still our parent/rcu_read_unlock/lock the child.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
It hangs the hardware.
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Pull ARM fixes from Russell King:
"The usual random collection of relatively small ARM fixes"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8063/1: bL_switcher: fix individual online status reporting of removed CPUs
ARM: 8064/1: fix v7-M signal return
ARM: 8057/1: amba: Add Qualcomm vendor ID.
ARM: 8052/1: unwind: Fix handling of "Pop r4-r[4+nnn],r14" opcode
ARM: 8051/1: put_user: fix possible data corruption in put_user
ARM: 8048/1: fix v7-M setup stack location
set_pte_at, which correctly handles PTE_WRITE and will mark the
resulting table entry as read-only where appropriate.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=o10I
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fix from Will Deacon:
"Fix CoW regression for transparent hugepages by routing set_pmd_at to
set_pte_at, which correctly handles PTE_WRITE and will mark the
resulting table entry as read-only where appropriate"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: fix pmd_write CoW brokenness
