linux_dsm_epyc7002/drivers/tty/serial/imx.c

2401 lines
63 KiB
C
Raw Normal View History

/*
* Driver for Motorola/Freescale IMX serial ports
*
* Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
*
* Author: Sascha Hauer <sascha@saschahauer.de>
* Copyright (C) 2004 Pengutronix
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#if defined(CONFIG_SERIAL_IMX_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
#define SUPPORT_SYSRQ
#endif
#include <linux/module.h>
#include <linux/ioport.h>
#include <linux/init.h>
#include <linux/console.h>
#include <linux/sysrq.h>
#include <linux/platform_device.h>
#include <linux/tty.h>
#include <linux/tty_flip.h>
#include <linux/serial_core.h>
#include <linux/serial.h>
#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/rational.h>
include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: Tejun Heo <tj@kernel.org> Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-24 15:04:11 +07:00
#include <linux/slab.h>
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/io.h>
#include <linux/dma-mapping.h>
#include <asm/irq.h>
#include <linux/platform_data/serial-imx.h>
#include <linux/platform_data/dma-imx.h>
#include "serial_mctrl_gpio.h"
/* Register definitions */
#define URXD0 0x0 /* Receiver Register */
#define URTX0 0x40 /* Transmitter Register */
#define UCR1 0x80 /* Control Register 1 */
#define UCR2 0x84 /* Control Register 2 */
#define UCR3 0x88 /* Control Register 3 */
#define UCR4 0x8c /* Control Register 4 */
#define UFCR 0x90 /* FIFO Control Register */
#define USR1 0x94 /* Status Register 1 */
#define USR2 0x98 /* Status Register 2 */
#define UESC 0x9c /* Escape Character Register */
#define UTIM 0xa0 /* Escape Timer Register */
#define UBIR 0xa4 /* BRM Incremental Register */
#define UBMR 0xa8 /* BRM Modulator Register */
#define UBRC 0xac /* Baud Rate Count Register */
#define IMX21_ONEMS 0xb0 /* One Millisecond register */
#define IMX1_UTS 0xd0 /* UART Test Register on i.mx1 */
#define IMX21_UTS 0xb4 /* UART Test Register on all other i.mx*/
/* UART Control Register Bit Fields.*/
#define URXD_DUMMY_READ (1<<16)
#define URXD_CHARRDY (1<<15)
#define URXD_ERR (1<<14)
#define URXD_OVRRUN (1<<13)
#define URXD_FRMERR (1<<12)
#define URXD_BRK (1<<11)
#define URXD_PRERR (1<<10)
#define URXD_RX_DATA (0xFF<<0)
#define UCR1_ADEN (1<<15) /* Auto detect interrupt */
#define UCR1_ADBR (1<<14) /* Auto detect baud rate */
#define UCR1_TRDYEN (1<<13) /* Transmitter ready interrupt enable */
#define UCR1_IDEN (1<<12) /* Idle condition interrupt */
#define UCR1_ICD_REG(x) (((x) & 3) << 10) /* idle condition detect */
#define UCR1_RRDYEN (1<<9) /* Recv ready interrupt enable */
#define UCR1_RDMAEN (1<<8) /* Recv ready DMA enable */
#define UCR1_IREN (1<<7) /* Infrared interface enable */
#define UCR1_TXMPTYEN (1<<6) /* Transimitter empty interrupt enable */
#define UCR1_RTSDEN (1<<5) /* RTS delta interrupt enable */
#define UCR1_SNDBRK (1<<4) /* Send break */
#define UCR1_TDMAEN (1<<3) /* Transmitter ready DMA enable */
#define IMX1_UCR1_UARTCLKEN (1<<2) /* UART clock enabled, i.mx1 only */
#define UCR1_ATDMAEN (1<<2) /* Aging DMA Timer Enable */
#define UCR1_DOZE (1<<1) /* Doze */
#define UCR1_UARTEN (1<<0) /* UART enabled */
#define UCR2_ESCI (1<<15) /* Escape seq interrupt enable */
#define UCR2_IRTS (1<<14) /* Ignore RTS pin */
#define UCR2_CTSC (1<<13) /* CTS pin control */
#define UCR2_CTS (1<<12) /* Clear to send */
#define UCR2_ESCEN (1<<11) /* Escape enable */
#define UCR2_PREN (1<<8) /* Parity enable */
#define UCR2_PROE (1<<7) /* Parity odd/even */
#define UCR2_STPB (1<<6) /* Stop */
#define UCR2_WS (1<<5) /* Word size */
#define UCR2_RTSEN (1<<4) /* Request to send interrupt enable */
#define UCR2_ATEN (1<<3) /* Aging Timer Enable */
#define UCR2_TXEN (1<<2) /* Transmitter enabled */
#define UCR2_RXEN (1<<1) /* Receiver enabled */
#define UCR2_SRST (1<<0) /* SW reset */
#define UCR3_DTREN (1<<13) /* DTR interrupt enable */
#define UCR3_PARERREN (1<<12) /* Parity enable */
#define UCR3_FRAERREN (1<<11) /* Frame error interrupt enable */
#define UCR3_DSR (1<<10) /* Data set ready */
#define UCR3_DCD (1<<9) /* Data carrier detect */
#define UCR3_RI (1<<8) /* Ring indicator */
#define UCR3_ADNIMP (1<<7) /* Autobaud Detection Not Improved */
#define UCR3_RXDSEN (1<<6) /* Receive status interrupt enable */
#define UCR3_AIRINTEN (1<<5) /* Async IR wake interrupt enable */
#define UCR3_AWAKEN (1<<4) /* Async wake interrupt enable */
#define UCR3_DTRDEN (1<<3) /* Data Terminal Ready Delta Enable. */
#define IMX21_UCR3_RXDMUXSEL (1<<2) /* RXD Muxed Input Select */
#define UCR3_INVT (1<<1) /* Inverted Infrared transmission */
#define UCR3_BPEN (1<<0) /* Preset registers enable */
#define UCR4_CTSTL_SHF 10 /* CTS trigger level shift */
#define UCR4_CTSTL_MASK 0x3F /* CTS trigger is 6 bits wide */
#define UCR4_INVR (1<<9) /* Inverted infrared reception */
#define UCR4_ENIRI (1<<8) /* Serial infrared interrupt enable */
#define UCR4_WKEN (1<<7) /* Wake interrupt enable */
#define UCR4_REF16 (1<<6) /* Ref freq 16 MHz */
#define UCR4_IDDMAEN (1<<6) /* DMA IDLE Condition Detected */
#define UCR4_IRSC (1<<5) /* IR special case */
#define UCR4_TCEN (1<<3) /* Transmit complete interrupt enable */
#define UCR4_BKEN (1<<2) /* Break condition interrupt enable */
#define UCR4_OREN (1<<1) /* Receiver overrun interrupt enable */
#define UCR4_DREN (1<<0) /* Recv data ready interrupt enable */
#define UFCR_RXTL_SHF 0 /* Receiver trigger level shift */
#define UFCR_DCEDTE (1<<6) /* DCE/DTE mode select */
#define UFCR_RFDIV (7<<7) /* Reference freq divider mask */
#define UFCR_RFDIV_REG(x) (((x) < 7 ? 6 - (x) : 6) << 7)
#define UFCR_TXTL_SHF 10 /* Transmitter trigger level shift */
#define USR1_PARITYERR (1<<15) /* Parity error interrupt flag */
#define USR1_RTSS (1<<14) /* RTS pin status */
#define USR1_TRDY (1<<13) /* Transmitter ready interrupt/dma flag */
#define USR1_RTSD (1<<12) /* RTS delta */
#define USR1_ESCF (1<<11) /* Escape seq interrupt flag */
#define USR1_FRAMERR (1<<10) /* Frame error interrupt flag */
#define USR1_RRDY (1<<9) /* Receiver ready interrupt/dma flag */
#define USR1_AGTIM (1<<8) /* Ageing timer interrupt flag */
#define USR1_DTRD (1<<7) /* DTR Delta */
#define USR1_RXDS (1<<6) /* Receiver idle interrupt flag */
#define USR1_AIRINT (1<<5) /* Async IR wake interrupt flag */
#define USR1_AWAKE (1<<4) /* Aysnc wake interrupt flag */
#define USR2_ADET (1<<15) /* Auto baud rate detect complete */
#define USR2_TXFE (1<<14) /* Transmit buffer FIFO empty */
#define USR2_DTRF (1<<13) /* DTR edge interrupt flag */
#define USR2_IDLE (1<<12) /* Idle condition */
#define USR2_RIDELT (1<<10) /* Ring Interrupt Delta */
#define USR2_RIIN (1<<9) /* Ring Indicator Input */
#define USR2_IRINT (1<<8) /* Serial infrared interrupt flag */
#define USR2_WAKE (1<<7) /* Wake */
#define USR2_DCDIN (1<<5) /* Data Carrier Detect Input */
#define USR2_RTSF (1<<4) /* RTS edge interrupt flag */
#define USR2_TXDC (1<<3) /* Transmitter complete */
#define USR2_BRCD (1<<2) /* Break condition */
#define USR2_ORE (1<<1) /* Overrun error */
#define USR2_RDR (1<<0) /* Recv data ready */
#define UTS_FRCPERR (1<<13) /* Force parity error */
#define UTS_LOOP (1<<12) /* Loop tx and rx */
#define UTS_TXEMPTY (1<<6) /* TxFIFO empty */
#define UTS_RXEMPTY (1<<5) /* RxFIFO empty */
#define UTS_TXFULL (1<<4) /* TxFIFO full */
#define UTS_RXFULL (1<<3) /* RxFIFO full */
#define UTS_SOFTRST (1<<0) /* Software reset */
/* We've been assigned a range on the "Low-density serial ports" major */
#define SERIAL_IMX_MAJOR 207
#define MINOR_START 16
#define DEV_NAME "ttymxc"
/*
* This determines how often we check the modem status signals
* for any change. They generally aren't connected to an IRQ
* so we have to poll them. We also check immediately before
* filling the TX fifo incase CTS has been dropped.
*/
#define MCTRL_TIMEOUT (250*HZ/1000)
#define DRIVER_NAME "IMX-uart"
#define UART_NR 8
/* i.MX21 type uart runs on all i.mx except i.MX1 and i.MX6q */
enum imx_uart_type {
IMX1_UART,
IMX21_UART,
IMX53_UART,
IMX6Q_UART,
};
/* device type dependent stuff */
struct imx_uart_data {
unsigned uts_reg;
enum imx_uart_type devtype;
};
struct imx_port {
struct uart_port port;
struct timer_list timer;
unsigned int old_status;
unsigned int have_rtscts:1;
unsigned int have_rtsgpio:1;
unsigned int dte_mode:1;
struct clk *clk_ipg;
struct clk *clk_per;
const struct imx_uart_data *devdata;
struct mctrl_gpios *gpios;
/* DMA fields */
unsigned int dma_is_inited:1;
unsigned int dma_is_enabled:1;
unsigned int dma_is_rxing:1;
unsigned int dma_is_txing:1;
struct dma_chan *dma_chan_rx, *dma_chan_tx;
struct scatterlist rx_sgl, tx_sgl[2];
void *rx_buf;
serial: imx-serial - update UART IMX driver to use cyclic DMA The IMX UART has a 32 bytes HW buffer which can be filled up in 2777us at 115200 baud or 80us at 4Mbaud (supported by IMX53). Taking this in consideration there is a good probability to lose data because of the DMA startup latency. Our tests (explained below) indicates a latency up to 4400us when creating interrupt load and ~70us without. When creating interrupt load I was able to see continuous overrun errors by checking serial driver statistics using the command: `cat /proc/tty/driver/IMX-uart`. Replace manual restart of DMA with cyclic DMA to eliminate data loss due to DMA engine startup latency (similar approch to atmel_serial.c driver). As result the DMA engine will start on the first serial data transfer and stops only when serial port is closed. Tests environment: Using the m53evk board I have used a GPIO for profiling the IMX serial driver. - The RX line and GPIO were connected to oscilloscope. - Run a small test program on the m53evk board that will only open and read data from ttymxc2 port. - Connect the ttymxc2 port to my laptop using a USB serial converter where another test program is running, able to send configurable packet lengths and intervals. - Serial ports configured at 115200 8N1. - Interrupts load created by disconnecting/connecting (3s interval) a USB hub, using a digital switch, with 4 USB devices (USB-Serial converter, USB SD card, etc) connected. (around 160 interrupts/second generated) - The GPIO was toggled HI in the `imx_int` when USR1_RRDY or USR1_AGTIM events are received and toggled back, once the DMA configuration is finalized, at the end of `imx_dma_rxint`. Measurements: The measurements were done from the end of the last byte (RX line) until the GPIO was toggled back LOW. Note: The GPIO toggling was done using `gpiod_set_value` method. Tests performed: 1. Sending 9 bytes packets at 8ms interval. Having the 9 bytes packets will activate the RRDY threshold event and IMX serial interrupt called. Results: - DMA start latency (interrupt start latency + DMA configuration) consistently 70us when system not loaded. - DMA start latency up to 4400us when system loaded. 2. Sending 40 bytes packet at 8mS interval. Results with load: - Able to observe overruns by running: `watch -n1 cat /proc/tty/driver/IMX-uart` Tested-by: Peter Senna Tschudin <peter.senna@collabora.com> Acked-by: Peter Senna Tschudin <peter.senna@collabora.com> Signed-off-by: Nandor Han <nandor.han@ge.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-08 19:38:27 +07:00
struct circ_buf rx_ring;
unsigned int rx_periods;
dma_cookie_t rx_cookie;
unsigned int tx_bytes;
unsigned int dma_tx_nents;
wait_queue_head_t dma_wait;
unsigned int saved_reg[10];
bool context_saved;
};
struct imx_port_ucrs {
unsigned int ucr1;
unsigned int ucr2;
unsigned int ucr3;
};
static struct imx_uart_data imx_uart_devdata[] = {
[IMX1_UART] = {
.uts_reg = IMX1_UTS,
.devtype = IMX1_UART,
},
[IMX21_UART] = {
.uts_reg = IMX21_UTS,
.devtype = IMX21_UART,
},
[IMX53_UART] = {
.uts_reg = IMX21_UTS,
.devtype = IMX53_UART,
},
[IMX6Q_UART] = {
.uts_reg = IMX21_UTS,
.devtype = IMX6Q_UART,
},
};
static const struct platform_device_id imx_uart_devtype[] = {
{
.name = "imx1-uart",
.driver_data = (kernel_ulong_t) &imx_uart_devdata[IMX1_UART],
}, {
.name = "imx21-uart",
.driver_data = (kernel_ulong_t) &imx_uart_devdata[IMX21_UART],
}, {
.name = "imx53-uart",
.driver_data = (kernel_ulong_t) &imx_uart_devdata[IMX53_UART],
}, {
.name = "imx6q-uart",
.driver_data = (kernel_ulong_t) &imx_uart_devdata[IMX6Q_UART],
}, {
/* sentinel */
}
};
MODULE_DEVICE_TABLE(platform, imx_uart_devtype);
static const struct of_device_id imx_uart_dt_ids[] = {
{ .compatible = "fsl,imx6q-uart", .data = &imx_uart_devdata[IMX6Q_UART], },
{ .compatible = "fsl,imx53-uart", .data = &imx_uart_devdata[IMX53_UART], },
{ .compatible = "fsl,imx1-uart", .data = &imx_uart_devdata[IMX1_UART], },
{ .compatible = "fsl,imx21-uart", .data = &imx_uart_devdata[IMX21_UART], },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, imx_uart_dt_ids);
static inline unsigned uts_reg(struct imx_port *sport)
{
return sport->devdata->uts_reg;
}
static inline int is_imx1_uart(struct imx_port *sport)
{
return sport->devdata->devtype == IMX1_UART;
}
static inline int is_imx21_uart(struct imx_port *sport)
{
return sport->devdata->devtype == IMX21_UART;
}
static inline int is_imx53_uart(struct imx_port *sport)
{
return sport->devdata->devtype == IMX53_UART;
}
static inline int is_imx6q_uart(struct imx_port *sport)
{
return sport->devdata->devtype == IMX6Q_UART;
}
/*
* Save and restore functions for UCR1, UCR2 and UCR3 registers
*/
#if defined(CONFIG_SERIAL_IMX_CONSOLE)
static void imx_port_ucrs_save(struct uart_port *port,
struct imx_port_ucrs *ucr)
{
/* save control registers */
ucr->ucr1 = readl(port->membase + UCR1);
ucr->ucr2 = readl(port->membase + UCR2);
ucr->ucr3 = readl(port->membase + UCR3);
}
static void imx_port_ucrs_restore(struct uart_port *port,
struct imx_port_ucrs *ucr)
{
/* restore control registers */
writel(ucr->ucr1, port->membase + UCR1);
writel(ucr->ucr2, port->membase + UCR2);
writel(ucr->ucr3, port->membase + UCR3);
}
#endif
static void imx_port_rts_active(struct imx_port *sport, unsigned long *ucr2)
{
*ucr2 &= ~(UCR2_CTSC | UCR2_CTS);
mctrl_gpio_set(sport->gpios, sport->port.mctrl | TIOCM_RTS);
}
static void imx_port_rts_inactive(struct imx_port *sport, unsigned long *ucr2)
{
*ucr2 &= ~UCR2_CTSC;
*ucr2 |= UCR2_CTS;
mctrl_gpio_set(sport->gpios, sport->port.mctrl & ~TIOCM_RTS);
}
static void imx_port_rts_auto(struct imx_port *sport, unsigned long *ucr2)
{
*ucr2 |= UCR2_CTSC;
}
/*
* interrupts disabled on entry
*/
static void imx_stop_tx(struct uart_port *port)
{
struct imx_port *sport = (struct imx_port *)port;
unsigned long temp;
/*
* We are maybe in the SMP context, so if the DMA TX thread is running
* on other cpu, we have to wait for it to finish.
*/
if (sport->dma_is_enabled && sport->dma_is_txing)
return;
temp = readl(port->membase + UCR1);
writel(temp & ~UCR1_TXMPTYEN, port->membase + UCR1);
/* in rs485 mode disable transmitter if shifter is empty */
if (port->rs485.flags & SER_RS485_ENABLED &&
readl(port->membase + USR2) & USR2_TXDC) {
temp = readl(port->membase + UCR2);
if (port->rs485.flags & SER_RS485_RTS_AFTER_SEND)
imx_port_rts_active(sport, &temp);
else
imx_port_rts_inactive(sport, &temp);
temp |= UCR2_RXEN;
writel(temp, port->membase + UCR2);
temp = readl(port->membase + UCR4);
temp &= ~UCR4_TCEN;
writel(temp, port->membase + UCR4);
}
}
/*
* interrupts disabled on entry
*/
static void imx_stop_rx(struct uart_port *port)
{
struct imx_port *sport = (struct imx_port *)port;
unsigned long temp;
if (sport->dma_is_enabled && sport->dma_is_rxing) {
if (sport->port.suspended) {
dmaengine_terminate_all(sport->dma_chan_rx);
sport->dma_is_rxing = 0;
} else {
return;
}
}
temp = readl(sport->port.membase + UCR2);
writel(temp & ~UCR2_RXEN, sport->port.membase + UCR2);
/* disable the `Receiver Ready Interrrupt` */
temp = readl(sport->port.membase + UCR1);
writel(temp & ~UCR1_RRDYEN, sport->port.membase + UCR1);
}
/*
* Set the modem control timer to fire immediately.
*/
static void imx_enable_ms(struct uart_port *port)
{
struct imx_port *sport = (struct imx_port *)port;
mod_timer(&sport->timer, jiffies);
mctrl_gpio_enable_ms(sport->gpios);
}
static void imx_dma_tx(struct imx_port *sport);
static inline void imx_transmit_buffer(struct imx_port *sport)
{
struct circ_buf *xmit = &sport->port.state->xmit;
unsigned long temp;
if (sport->port.x_char) {
/* Send next char */
writel(sport->port.x_char, sport->port.membase + URTX0);
sport->port.icount.tx++;
sport->port.x_char = 0;
return;
}
if (uart_circ_empty(xmit) || uart_tx_stopped(&sport->port)) {
imx_stop_tx(&sport->port);
return;
}
if (sport->dma_is_enabled) {
/*
* We've just sent a X-char Ensure the TX DMA is enabled
* and the TX IRQ is disabled.
**/
temp = readl(sport->port.membase + UCR1);
temp &= ~UCR1_TXMPTYEN;
if (sport->dma_is_txing) {
temp |= UCR1_TDMAEN;
writel(temp, sport->port.membase + UCR1);
} else {
writel(temp, sport->port.membase + UCR1);
imx_dma_tx(sport);
}
}
while (!uart_circ_empty(xmit) && !sport->dma_is_txing &&
!(readl(sport->port.membase + uts_reg(sport)) & UTS_TXFULL)) {
/* send xmit->buf[xmit->tail]
* out the port here */
writel(xmit->buf[xmit->tail], sport->port.membase + URTX0);
xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
sport->port.icount.tx++;
}
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
uart_write_wakeup(&sport->port);
if (uart_circ_empty(xmit))
imx_stop_tx(&sport->port);
}
static void dma_tx_callback(void *data)
{
struct imx_port *sport = data;
struct scatterlist *sgl = &sport->tx_sgl[0];
struct circ_buf *xmit = &sport->port.state->xmit;
unsigned long flags;
unsigned long temp;
spin_lock_irqsave(&sport->port.lock, flags);
dma_unmap_sg(sport->port.dev, sgl, sport->dma_tx_nents, DMA_TO_DEVICE);
temp = readl(sport->port.membase + UCR1);
temp &= ~UCR1_TDMAEN;
writel(temp, sport->port.membase + UCR1);
/* update the stat */
xmit->tail = (xmit->tail + sport->tx_bytes) & (UART_XMIT_SIZE - 1);
sport->port.icount.tx += sport->tx_bytes;
dev_dbg(sport->port.dev, "we finish the TX DMA.\n");
sport->dma_is_txing = 0;
spin_unlock_irqrestore(&sport->port.lock, flags);
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
uart_write_wakeup(&sport->port);
if (waitqueue_active(&sport->dma_wait)) {
wake_up(&sport->dma_wait);
dev_dbg(sport->port.dev, "exit in %s.\n", __func__);
return;
}
spin_lock_irqsave(&sport->port.lock, flags);
if (!uart_circ_empty(xmit) && !uart_tx_stopped(&sport->port))
imx_dma_tx(sport);
spin_unlock_irqrestore(&sport->port.lock, flags);
}
static void imx_dma_tx(struct imx_port *sport)
{
struct circ_buf *xmit = &sport->port.state->xmit;
struct scatterlist *sgl = sport->tx_sgl;
struct dma_async_tx_descriptor *desc;
struct dma_chan *chan = sport->dma_chan_tx;
struct device *dev = sport->port.dev;
unsigned long temp;
int ret;
if (sport->dma_is_txing)
return;
sport->tx_bytes = uart_circ_chars_pending(xmit);
if (xmit->tail < xmit->head) {
sport->dma_tx_nents = 1;
sg_init_one(sgl, xmit->buf + xmit->tail, sport->tx_bytes);
} else {
sport->dma_tx_nents = 2;
sg_init_table(sgl, 2);
sg_set_buf(sgl, xmit->buf + xmit->tail,
UART_XMIT_SIZE - xmit->tail);
sg_set_buf(sgl + 1, xmit->buf, xmit->head);
}
ret = dma_map_sg(dev, sgl, sport->dma_tx_nents, DMA_TO_DEVICE);
if (ret == 0) {
dev_err(dev, "DMA mapping error for TX.\n");
return;
}
desc = dmaengine_prep_slave_sg(chan, sgl, sport->dma_tx_nents,
DMA_MEM_TO_DEV, DMA_PREP_INTERRUPT);
if (!desc) {
dma_unmap_sg(dev, sgl, sport->dma_tx_nents,
DMA_TO_DEVICE);
dev_err(dev, "We cannot prepare for the TX slave dma!\n");
return;
}
desc->callback = dma_tx_callback;
desc->callback_param = sport;
dev_dbg(dev, "TX: prepare to send %lu bytes by DMA.\n",
uart_circ_chars_pending(xmit));
temp = readl(sport->port.membase + UCR1);
temp |= UCR1_TDMAEN;
writel(temp, sport->port.membase + UCR1);
/* fire it */
sport->dma_is_txing = 1;
dmaengine_submit(desc);
dma_async_issue_pending(chan);
return;
}
/*
* interrupts disabled on entry
*/
static void imx_start_tx(struct uart_port *port)
{
struct imx_port *sport = (struct imx_port *)port;
unsigned long temp;
if (port->rs485.flags & SER_RS485_ENABLED) {
temp = readl(port->membase + UCR2);
if (port->rs485.flags & SER_RS485_RTS_ON_SEND)
imx_port_rts_active(sport, &temp);
else
imx_port_rts_inactive(sport, &temp);
if (!(port->rs485.flags & SER_RS485_RX_DURING_TX))
temp &= ~UCR2_RXEN;
writel(temp, port->membase + UCR2);
/* enable transmitter and shifter empty irq */
temp = readl(port->membase + UCR4);
temp |= UCR4_TCEN;
writel(temp, port->membase + UCR4);
}
if (!sport->dma_is_enabled) {
temp = readl(sport->port.membase + UCR1);
writel(temp | UCR1_TXMPTYEN, sport->port.membase + UCR1);
}
if (sport->dma_is_enabled) {
if (sport->port.x_char) {
/* We have X-char to send, so enable TX IRQ and
* disable TX DMA to let TX interrupt to send X-char */
temp = readl(sport->port.membase + UCR1);
temp &= ~UCR1_TDMAEN;
temp |= UCR1_TXMPTYEN;
writel(temp, sport->port.membase + UCR1);
return;
}
if (!uart_circ_empty(&port->state->xmit) &&
!uart_tx_stopped(port))
imx_dma_tx(sport);
return;
}
}
IRQ: Maintain regs pointer globally rather than passing to IRQ handlers Maintain a per-CPU global "struct pt_regs *" variable which can be used instead of passing regs around manually through all ~1800 interrupt handlers in the Linux kernel. The regs pointer is used in few places, but it potentially costs both stack space and code to pass it around. On the FRV arch, removing the regs parameter from all the genirq function results in a 20% speed up of the IRQ exit path (ie: from leaving timer_interrupt() to leaving do_IRQ()). Where appropriate, an arch may override the generic storage facility and do something different with the variable. On FRV, for instance, the address is maintained in GR28 at all times inside the kernel as part of general exception handling. Having looked over the code, it appears that the parameter may be handed down through up to twenty or so layers of functions. Consider a USB character device attached to a USB hub, attached to a USB controller that posts its interrupts through a cascaded auxiliary interrupt controller. A character device driver may want to pass regs to the sysrq handler through the input layer which adds another few layers of parameter passing. I've build this code with allyesconfig for x86_64 and i386. I've runtested the main part of the code on FRV and i386, though I can't test most of the drivers. I've also done partial conversion for powerpc and MIPS - these at least compile with minimal configurations. This will affect all archs. Mostly the changes should be relatively easy. Take do_IRQ(), store the regs pointer at the beginning, saving the old one: struct pt_regs *old_regs = set_irq_regs(regs); And put the old one back at the end: set_irq_regs(old_regs); Don't pass regs through to generic_handle_irq() or __do_IRQ(). In timer_interrupt(), this sort of change will be necessary: - update_process_times(user_mode(regs)); - profile_tick(CPU_PROFILING, regs); + update_process_times(user_mode(get_irq_regs())); + profile_tick(CPU_PROFILING); I'd like to move update_process_times()'s use of get_irq_regs() into itself, except that i386, alone of the archs, uses something other than user_mode(). Some notes on the interrupt handling in the drivers: (*) input_dev() is now gone entirely. The regs pointer is no longer stored in the input_dev struct. (*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does something different depending on whether it's been supplied with a regs pointer or not. (*) Various IRQ handler function pointers have been moved to type irq_handler_t. Signed-Off-By: David Howells <dhowells@redhat.com> (cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
2006-10-05 20:55:46 +07:00
static irqreturn_t imx_rtsint(int irq, void *dev_id)
{
struct imx_port *sport = dev_id;
unsigned int val;
unsigned long flags;
spin_lock_irqsave(&sport->port.lock, flags);
writel(USR1_RTSD, sport->port.membase + USR1);
val = readl(sport->port.membase + USR1) & USR1_RTSS;
uart_handle_cts_change(&sport->port, !!val);
wake_up_interruptible(&sport->port.state->port.delta_msr_wait);
spin_unlock_irqrestore(&sport->port.lock, flags);
return IRQ_HANDLED;
}
IRQ: Maintain regs pointer globally rather than passing to IRQ handlers Maintain a per-CPU global "struct pt_regs *" variable which can be used instead of passing regs around manually through all ~1800 interrupt handlers in the Linux kernel. The regs pointer is used in few places, but it potentially costs both stack space and code to pass it around. On the FRV arch, removing the regs parameter from all the genirq function results in a 20% speed up of the IRQ exit path (ie: from leaving timer_interrupt() to leaving do_IRQ()). Where appropriate, an arch may override the generic storage facility and do something different with the variable. On FRV, for instance, the address is maintained in GR28 at all times inside the kernel as part of general exception handling. Having looked over the code, it appears that the parameter may be handed down through up to twenty or so layers of functions. Consider a USB character device attached to a USB hub, attached to a USB controller that posts its interrupts through a cascaded auxiliary interrupt controller. A character device driver may want to pass regs to the sysrq handler through the input layer which adds another few layers of parameter passing. I've build this code with allyesconfig for x86_64 and i386. I've runtested the main part of the code on FRV and i386, though I can't test most of the drivers. I've also done partial conversion for powerpc and MIPS - these at least compile with minimal configurations. This will affect all archs. Mostly the changes should be relatively easy. Take do_IRQ(), store the regs pointer at the beginning, saving the old one: struct pt_regs *old_regs = set_irq_regs(regs); And put the old one back at the end: set_irq_regs(old_regs); Don't pass regs through to generic_handle_irq() or __do_IRQ(). In timer_interrupt(), this sort of change will be necessary: - update_process_times(user_mode(regs)); - profile_tick(CPU_PROFILING, regs); + update_process_times(user_mode(get_irq_regs())); + profile_tick(CPU_PROFILING); I'd like to move update_process_times()'s use of get_irq_regs() into itself, except that i386, alone of the archs, uses something other than user_mode(). Some notes on the interrupt handling in the drivers: (*) input_dev() is now gone entirely. The regs pointer is no longer stored in the input_dev struct. (*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does something different depending on whether it's been supplied with a regs pointer or not. (*) Various IRQ handler function pointers have been moved to type irq_handler_t. Signed-Off-By: David Howells <dhowells@redhat.com> (cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
2006-10-05 20:55:46 +07:00
static irqreturn_t imx_txint(int irq, void *dev_id)
{
struct imx_port *sport = dev_id;
unsigned long flags;
spin_lock_irqsave(&sport->port.lock, flags);
imx_transmit_buffer(sport);
spin_unlock_irqrestore(&sport->port.lock, flags);
return IRQ_HANDLED;
}
IRQ: Maintain regs pointer globally rather than passing to IRQ handlers Maintain a per-CPU global "struct pt_regs *" variable which can be used instead of passing regs around manually through all ~1800 interrupt handlers in the Linux kernel. The regs pointer is used in few places, but it potentially costs both stack space and code to pass it around. On the FRV arch, removing the regs parameter from all the genirq function results in a 20% speed up of the IRQ exit path (ie: from leaving timer_interrupt() to leaving do_IRQ()). Where appropriate, an arch may override the generic storage facility and do something different with the variable. On FRV, for instance, the address is maintained in GR28 at all times inside the kernel as part of general exception handling. Having looked over the code, it appears that the parameter may be handed down through up to twenty or so layers of functions. Consider a USB character device attached to a USB hub, attached to a USB controller that posts its interrupts through a cascaded auxiliary interrupt controller. A character device driver may want to pass regs to the sysrq handler through the input layer which adds another few layers of parameter passing. I've build this code with allyesconfig for x86_64 and i386. I've runtested the main part of the code on FRV and i386, though I can't test most of the drivers. I've also done partial conversion for powerpc and MIPS - these at least compile with minimal configurations. This will affect all archs. Mostly the changes should be relatively easy. Take do_IRQ(), store the regs pointer at the beginning, saving the old one: struct pt_regs *old_regs = set_irq_regs(regs); And put the old one back at the end: set_irq_regs(old_regs); Don't pass regs through to generic_handle_irq() or __do_IRQ(). In timer_interrupt(), this sort of change will be necessary: - update_process_times(user_mode(regs)); - profile_tick(CPU_PROFILING, regs); + update_process_times(user_mode(get_irq_regs())); + profile_tick(CPU_PROFILING); I'd like to move update_process_times()'s use of get_irq_regs() into itself, except that i386, alone of the archs, uses something other than user_mode(). Some notes on the interrupt handling in the drivers: (*) input_dev() is now gone entirely. The regs pointer is no longer stored in the input_dev struct. (*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does something different depending on whether it's been supplied with a regs pointer or not. (*) Various IRQ handler function pointers have been moved to type irq_handler_t. Signed-Off-By: David Howells <dhowells@redhat.com> (cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
2006-10-05 20:55:46 +07:00
static irqreturn_t imx_rxint(int irq, void *dev_id)
{
struct imx_port *sport = dev_id;
unsigned int rx, flg, ignored = 0;
struct tty_port *port = &sport->port.state->port;
unsigned long flags, temp;
spin_lock_irqsave(&sport->port.lock, flags);
while (readl(sport->port.membase + USR2) & USR2_RDR) {
flg = TTY_NORMAL;
sport->port.icount.rx++;
rx = readl(sport->port.membase + URXD0);
temp = readl(sport->port.membase + USR2);
if (temp & USR2_BRCD) {
writel(USR2_BRCD, sport->port.membase + USR2);
if (uart_handle_break(&sport->port))
continue;
}
if (uart_handle_sysrq_char(&sport->port, (unsigned char)rx))
continue;
if (unlikely(rx & URXD_ERR)) {
if (rx & URXD_BRK)
sport->port.icount.brk++;
else if (rx & URXD_PRERR)
sport->port.icount.parity++;
else if (rx & URXD_FRMERR)
sport->port.icount.frame++;
if (rx & URXD_OVRRUN)
sport->port.icount.overrun++;
if (rx & sport->port.ignore_status_mask) {
if (++ignored > 100)
goto out;
continue;
}
rx &= (sport->port.read_status_mask | 0xFF);
if (rx & URXD_BRK)
flg = TTY_BREAK;
else if (rx & URXD_PRERR)
flg = TTY_PARITY;
else if (rx & URXD_FRMERR)
flg = TTY_FRAME;
if (rx & URXD_OVRRUN)
flg = TTY_OVERRUN;
#ifdef SUPPORT_SYSRQ
sport->port.sysrq = 0;
#endif
}
if (sport->port.ignore_status_mask & URXD_DUMMY_READ)
goto out;
if (tty_insert_flip_char(port, rx, flg) == 0)
sport->port.icount.buf_overrun++;
}
out:
spin_unlock_irqrestore(&sport->port.lock, flags);
tty_flip_buffer_push(port);
return IRQ_HANDLED;
}
static void imx_disable_rx_int(struct imx_port *sport)
{
unsigned long temp;
sport->dma_is_rxing = 1;
/* disable the receiver ready and aging timer interrupts */
temp = readl(sport->port.membase + UCR1);
temp &= ~(UCR1_RRDYEN);
writel(temp, sport->port.membase + UCR1);
temp = readl(sport->port.membase + UCR2);
temp &= ~(UCR2_ATEN);
writel(temp, sport->port.membase + UCR2);
/* disable the rx errors interrupts */
temp = readl(sport->port.membase + UCR4);
temp &= ~UCR4_OREN;
writel(temp, sport->port.membase + UCR4);
}
static void clear_rx_errors(struct imx_port *sport);
static int start_rx_dma(struct imx_port *sport);
/*
* If the RXFIFO is filled with some data, and then we
* arise a DMA operation to receive them.
*/
static void imx_dma_rxint(struct imx_port *sport)
{
unsigned long temp;
unsigned long flags;
spin_lock_irqsave(&sport->port.lock, flags);
temp = readl(sport->port.membase + USR2);
if ((temp & USR2_RDR) && !sport->dma_is_rxing) {
imx_disable_rx_int(sport);
/* tell the DMA to receive the data. */
start_rx_dma(sport);
}
spin_unlock_irqrestore(&sport->port.lock, flags);
}
/*
* We have a modem side uart, so the meanings of RTS and CTS are inverted.
*/
static unsigned int imx_get_hwmctrl(struct imx_port *sport)
{
unsigned int tmp = TIOCM_DSR;
unsigned usr1 = readl(sport->port.membase + USR1);
unsigned usr2 = readl(sport->port.membase + USR2);
if (usr1 & USR1_RTSS)
tmp |= TIOCM_CTS;
/* in DCE mode DCDIN is always 0 */
if (!(usr2 & USR2_DCDIN))
tmp |= TIOCM_CAR;
if (sport->dte_mode)
if (!(readl(sport->port.membase + USR2) & USR2_RIIN))
tmp |= TIOCM_RI;
return tmp;
}
/*
* Handle any change of modem status signal since we were last called.
*/
static void imx_mctrl_check(struct imx_port *sport)
{
unsigned int status, changed;
status = imx_get_hwmctrl(sport);
changed = status ^ sport->old_status;
if (changed == 0)
return;
sport->old_status = status;
if (changed & TIOCM_RI && status & TIOCM_RI)
sport->port.icount.rng++;
if (changed & TIOCM_DSR)
sport->port.icount.dsr++;
if (changed & TIOCM_CAR)
uart_handle_dcd_change(&sport->port, status & TIOCM_CAR);
if (changed & TIOCM_CTS)
uart_handle_cts_change(&sport->port, status & TIOCM_CTS);
wake_up_interruptible(&sport->port.state->port.delta_msr_wait);
}
static irqreturn_t imx_int(int irq, void *dev_id)
{
struct imx_port *sport = dev_id;
unsigned int sts;
unsigned int sts2;
irqreturn_t ret = IRQ_NONE;
sts = readl(sport->port.membase + USR1);
sts2 = readl(sport->port.membase + USR2);
if (sts & (USR1_RRDY | USR1_AGTIM)) {
if (sport->dma_is_enabled)
imx_dma_rxint(sport);
else
imx_rxint(irq, dev_id);
ret = IRQ_HANDLED;
}
if ((sts & USR1_TRDY &&
readl(sport->port.membase + UCR1) & UCR1_TXMPTYEN) ||
(sts2 & USR2_TXDC &&
readl(sport->port.membase + UCR4) & UCR4_TCEN)) {
imx_txint(irq, dev_id);
ret = IRQ_HANDLED;
}
if (sts & USR1_DTRD) {
unsigned long flags;
if (sts & USR1_DTRD)
writel(USR1_DTRD, sport->port.membase + USR1);
spin_lock_irqsave(&sport->port.lock, flags);
imx_mctrl_check(sport);
spin_unlock_irqrestore(&sport->port.lock, flags);
ret = IRQ_HANDLED;
}
if (sts & USR1_RTSD) {
imx_rtsint(irq, dev_id);
ret = IRQ_HANDLED;
}
if (sts & USR1_AWAKE) {
writel(USR1_AWAKE, sport->port.membase + USR1);
ret = IRQ_HANDLED;
}
if (sts2 & USR2_ORE) {
sport->port.icount.overrun++;
writel(USR2_ORE, sport->port.membase + USR2);
ret = IRQ_HANDLED;
}
return ret;
}
/*
* Return TIOCSER_TEMT when transmitter is not busy.
*/
static unsigned int imx_tx_empty(struct uart_port *port)
{
struct imx_port *sport = (struct imx_port *)port;
unsigned int ret;
ret = (readl(sport->port.membase + USR2) & USR2_TXDC) ? TIOCSER_TEMT : 0;
/* If the TX DMA is working, return 0. */
if (sport->dma_is_enabled && sport->dma_is_txing)
ret = 0;
return ret;
}
static unsigned int imx_get_mctrl(struct uart_port *port)
{
struct imx_port *sport = (struct imx_port *)port;
unsigned int ret = imx_get_hwmctrl(sport);
mctrl_gpio_get(sport->gpios, &ret);
return ret;
}
static void imx_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
struct imx_port *sport = (struct imx_port *)port;
unsigned long temp;
if (!(port->rs485.flags & SER_RS485_ENABLED)) {
temp = readl(sport->port.membase + UCR2);
temp &= ~(UCR2_CTS | UCR2_CTSC);
if (mctrl & TIOCM_RTS)
temp |= UCR2_CTS | UCR2_CTSC;
writel(temp, sport->port.membase + UCR2);
}
temp = readl(sport->port.membase + UCR3) & ~UCR3_DSR;
if (!(mctrl & TIOCM_DTR))
temp |= UCR3_DSR;
writel(temp, sport->port.membase + UCR3);
temp = readl(sport->port.membase + uts_reg(sport)) & ~UTS_LOOP;
if (mctrl & TIOCM_LOOP)
temp |= UTS_LOOP;
writel(temp, sport->port.membase + uts_reg(sport));
mctrl_gpio_set(sport->gpios, mctrl);
}
/*
* Interrupts always disabled.
*/
static void imx_break_ctl(struct uart_port *port, int break_state)
{
struct imx_port *sport = (struct imx_port *)port;
unsigned long flags, temp;
spin_lock_irqsave(&sport->port.lock, flags);
temp = readl(sport->port.membase + UCR1) & ~UCR1_SNDBRK;
if (break_state != 0)
temp |= UCR1_SNDBRK;
writel(temp, sport->port.membase + UCR1);
spin_unlock_irqrestore(&sport->port.lock, flags);
}
/*
* This is our per-port timeout handler, for checking the
* modem status signals.
*/
static void imx_timeout(unsigned long data)
{
struct imx_port *sport = (struct imx_port *)data;
unsigned long flags;
if (sport->port.state) {
spin_lock_irqsave(&sport->port.lock, flags);
imx_mctrl_check(sport);
spin_unlock_irqrestore(&sport->port.lock, flags);
mod_timer(&sport->timer, jiffies + MCTRL_TIMEOUT);
}
}
#define RX_BUF_SIZE (PAGE_SIZE)
/*
* There are two kinds of RX DMA interrupts(such as in the MX6Q):
* [1] the RX DMA buffer is full.
* [2] the aging timer expires
*
* Condition [2] is triggered when a character has been sitting in the FIFO
* for at least 8 byte durations.
*/
static void dma_rx_callback(void *data)
{
struct imx_port *sport = data;
struct dma_chan *chan = sport->dma_chan_rx;
struct scatterlist *sgl = &sport->rx_sgl;
struct tty_port *port = &sport->port.state->port;
struct dma_tx_state state;
serial: imx-serial - update UART IMX driver to use cyclic DMA The IMX UART has a 32 bytes HW buffer which can be filled up in 2777us at 115200 baud or 80us at 4Mbaud (supported by IMX53). Taking this in consideration there is a good probability to lose data because of the DMA startup latency. Our tests (explained below) indicates a latency up to 4400us when creating interrupt load and ~70us without. When creating interrupt load I was able to see continuous overrun errors by checking serial driver statistics using the command: `cat /proc/tty/driver/IMX-uart`. Replace manual restart of DMA with cyclic DMA to eliminate data loss due to DMA engine startup latency (similar approch to atmel_serial.c driver). As result the DMA engine will start on the first serial data transfer and stops only when serial port is closed. Tests environment: Using the m53evk board I have used a GPIO for profiling the IMX serial driver. - The RX line and GPIO were connected to oscilloscope. - Run a small test program on the m53evk board that will only open and read data from ttymxc2 port. - Connect the ttymxc2 port to my laptop using a USB serial converter where another test program is running, able to send configurable packet lengths and intervals. - Serial ports configured at 115200 8N1. - Interrupts load created by disconnecting/connecting (3s interval) a USB hub, using a digital switch, with 4 USB devices (USB-Serial converter, USB SD card, etc) connected. (around 160 interrupts/second generated) - The GPIO was toggled HI in the `imx_int` when USR1_RRDY or USR1_AGTIM events are received and toggled back, once the DMA configuration is finalized, at the end of `imx_dma_rxint`. Measurements: The measurements were done from the end of the last byte (RX line) until the GPIO was toggled back LOW. Note: The GPIO toggling was done using `gpiod_set_value` method. Tests performed: 1. Sending 9 bytes packets at 8ms interval. Having the 9 bytes packets will activate the RRDY threshold event and IMX serial interrupt called. Results: - DMA start latency (interrupt start latency + DMA configuration) consistently 70us when system not loaded. - DMA start latency up to 4400us when system loaded. 2. Sending 40 bytes packet at 8mS interval. Results with load: - Able to observe overruns by running: `watch -n1 cat /proc/tty/driver/IMX-uart` Tested-by: Peter Senna Tschudin <peter.senna@collabora.com> Acked-by: Peter Senna Tschudin <peter.senna@collabora.com> Signed-off-by: Nandor Han <nandor.han@ge.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-08 19:38:27 +07:00
struct circ_buf *rx_ring = &sport->rx_ring;
enum dma_status status;
serial: imx-serial - update UART IMX driver to use cyclic DMA The IMX UART has a 32 bytes HW buffer which can be filled up in 2777us at 115200 baud or 80us at 4Mbaud (supported by IMX53). Taking this in consideration there is a good probability to lose data because of the DMA startup latency. Our tests (explained below) indicates a latency up to 4400us when creating interrupt load and ~70us without. When creating interrupt load I was able to see continuous overrun errors by checking serial driver statistics using the command: `cat /proc/tty/driver/IMX-uart`. Replace manual restart of DMA with cyclic DMA to eliminate data loss due to DMA engine startup latency (similar approch to atmel_serial.c driver). As result the DMA engine will start on the first serial data transfer and stops only when serial port is closed. Tests environment: Using the m53evk board I have used a GPIO for profiling the IMX serial driver. - The RX line and GPIO were connected to oscilloscope. - Run a small test program on the m53evk board that will only open and read data from ttymxc2 port. - Connect the ttymxc2 port to my laptop using a USB serial converter where another test program is running, able to send configurable packet lengths and intervals. - Serial ports configured at 115200 8N1. - Interrupts load created by disconnecting/connecting (3s interval) a USB hub, using a digital switch, with 4 USB devices (USB-Serial converter, USB SD card, etc) connected. (around 160 interrupts/second generated) - The GPIO was toggled HI in the `imx_int` when USR1_RRDY or USR1_AGTIM events are received and toggled back, once the DMA configuration is finalized, at the end of `imx_dma_rxint`. Measurements: The measurements were done from the end of the last byte (RX line) until the GPIO was toggled back LOW. Note: The GPIO toggling was done using `gpiod_set_value` method. Tests performed: 1. Sending 9 bytes packets at 8ms interval. Having the 9 bytes packets will activate the RRDY threshold event and IMX serial interrupt called. Results: - DMA start latency (interrupt start latency + DMA configuration) consistently 70us when system not loaded. - DMA start latency up to 4400us when system loaded. 2. Sending 40 bytes packet at 8mS interval. Results with load: - Able to observe overruns by running: `watch -n1 cat /proc/tty/driver/IMX-uart` Tested-by: Peter Senna Tschudin <peter.senna@collabora.com> Acked-by: Peter Senna Tschudin <peter.senna@collabora.com> Signed-off-by: Nandor Han <nandor.han@ge.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-08 19:38:27 +07:00
unsigned int w_bytes = 0;
unsigned int r_bytes;
unsigned int bd_size;
status = dmaengine_tx_status(chan, (dma_cookie_t)0, &state);
serial: imx-serial - update UART IMX driver to use cyclic DMA The IMX UART has a 32 bytes HW buffer which can be filled up in 2777us at 115200 baud or 80us at 4Mbaud (supported by IMX53). Taking this in consideration there is a good probability to lose data because of the DMA startup latency. Our tests (explained below) indicates a latency up to 4400us when creating interrupt load and ~70us without. When creating interrupt load I was able to see continuous overrun errors by checking serial driver statistics using the command: `cat /proc/tty/driver/IMX-uart`. Replace manual restart of DMA with cyclic DMA to eliminate data loss due to DMA engine startup latency (similar approch to atmel_serial.c driver). As result the DMA engine will start on the first serial data transfer and stops only when serial port is closed. Tests environment: Using the m53evk board I have used a GPIO for profiling the IMX serial driver. - The RX line and GPIO were connected to oscilloscope. - Run a small test program on the m53evk board that will only open and read data from ttymxc2 port. - Connect the ttymxc2 port to my laptop using a USB serial converter where another test program is running, able to send configurable packet lengths and intervals. - Serial ports configured at 115200 8N1. - Interrupts load created by disconnecting/connecting (3s interval) a USB hub, using a digital switch, with 4 USB devices (USB-Serial converter, USB SD card, etc) connected. (around 160 interrupts/second generated) - The GPIO was toggled HI in the `imx_int` when USR1_RRDY or USR1_AGTIM events are received and toggled back, once the DMA configuration is finalized, at the end of `imx_dma_rxint`. Measurements: The measurements were done from the end of the last byte (RX line) until the GPIO was toggled back LOW. Note: The GPIO toggling was done using `gpiod_set_value` method. Tests performed: 1. Sending 9 bytes packets at 8ms interval. Having the 9 bytes packets will activate the RRDY threshold event and IMX serial interrupt called. Results: - DMA start latency (interrupt start latency + DMA configuration) consistently 70us when system not loaded. - DMA start latency up to 4400us when system loaded. 2. Sending 40 bytes packet at 8mS interval. Results with load: - Able to observe overruns by running: `watch -n1 cat /proc/tty/driver/IMX-uart` Tested-by: Peter Senna Tschudin <peter.senna@collabora.com> Acked-by: Peter Senna Tschudin <peter.senna@collabora.com> Signed-off-by: Nandor Han <nandor.han@ge.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-08 19:38:27 +07:00
if (status == DMA_ERROR) {
dev_err(sport->port.dev, "DMA transaction error.\n");
clear_rx_errors(sport);
serial: imx-serial - update UART IMX driver to use cyclic DMA The IMX UART has a 32 bytes HW buffer which can be filled up in 2777us at 115200 baud or 80us at 4Mbaud (supported by IMX53). Taking this in consideration there is a good probability to lose data because of the DMA startup latency. Our tests (explained below) indicates a latency up to 4400us when creating interrupt load and ~70us without. When creating interrupt load I was able to see continuous overrun errors by checking serial driver statistics using the command: `cat /proc/tty/driver/IMX-uart`. Replace manual restart of DMA with cyclic DMA to eliminate data loss due to DMA engine startup latency (similar approch to atmel_serial.c driver). As result the DMA engine will start on the first serial data transfer and stops only when serial port is closed. Tests environment: Using the m53evk board I have used a GPIO for profiling the IMX serial driver. - The RX line and GPIO were connected to oscilloscope. - Run a small test program on the m53evk board that will only open and read data from ttymxc2 port. - Connect the ttymxc2 port to my laptop using a USB serial converter where another test program is running, able to send configurable packet lengths and intervals. - Serial ports configured at 115200 8N1. - Interrupts load created by disconnecting/connecting (3s interval) a USB hub, using a digital switch, with 4 USB devices (USB-Serial converter, USB SD card, etc) connected. (around 160 interrupts/second generated) - The GPIO was toggled HI in the `imx_int` when USR1_RRDY or USR1_AGTIM events are received and toggled back, once the DMA configuration is finalized, at the end of `imx_dma_rxint`. Measurements: The measurements were done from the end of the last byte (RX line) until the GPIO was toggled back LOW. Note: The GPIO toggling was done using `gpiod_set_value` method. Tests performed: 1. Sending 9 bytes packets at 8ms interval. Having the 9 bytes packets will activate the RRDY threshold event and IMX serial interrupt called. Results: - DMA start latency (interrupt start latency + DMA configuration) consistently 70us when system not loaded. - DMA start latency up to 4400us when system loaded. 2. Sending 40 bytes packet at 8mS interval. Results with load: - Able to observe overruns by running: `watch -n1 cat /proc/tty/driver/IMX-uart` Tested-by: Peter Senna Tschudin <peter.senna@collabora.com> Acked-by: Peter Senna Tschudin <peter.senna@collabora.com> Signed-off-by: Nandor Han <nandor.han@ge.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-08 19:38:27 +07:00
return;
}
if (!(sport->port.ignore_status_mask & URXD_DUMMY_READ)) {
serial: imx-serial - update UART IMX driver to use cyclic DMA The IMX UART has a 32 bytes HW buffer which can be filled up in 2777us at 115200 baud or 80us at 4Mbaud (supported by IMX53). Taking this in consideration there is a good probability to lose data because of the DMA startup latency. Our tests (explained below) indicates a latency up to 4400us when creating interrupt load and ~70us without. When creating interrupt load I was able to see continuous overrun errors by checking serial driver statistics using the command: `cat /proc/tty/driver/IMX-uart`. Replace manual restart of DMA with cyclic DMA to eliminate data loss due to DMA engine startup latency (similar approch to atmel_serial.c driver). As result the DMA engine will start on the first serial data transfer and stops only when serial port is closed. Tests environment: Using the m53evk board I have used a GPIO for profiling the IMX serial driver. - The RX line and GPIO were connected to oscilloscope. - Run a small test program on the m53evk board that will only open and read data from ttymxc2 port. - Connect the ttymxc2 port to my laptop using a USB serial converter where another test program is running, able to send configurable packet lengths and intervals. - Serial ports configured at 115200 8N1. - Interrupts load created by disconnecting/connecting (3s interval) a USB hub, using a digital switch, with 4 USB devices (USB-Serial converter, USB SD card, etc) connected. (around 160 interrupts/second generated) - The GPIO was toggled HI in the `imx_int` when USR1_RRDY or USR1_AGTIM events are received and toggled back, once the DMA configuration is finalized, at the end of `imx_dma_rxint`. Measurements: The measurements were done from the end of the last byte (RX line) until the GPIO was toggled back LOW. Note: The GPIO toggling was done using `gpiod_set_value` method. Tests performed: 1. Sending 9 bytes packets at 8ms interval. Having the 9 bytes packets will activate the RRDY threshold event and IMX serial interrupt called. Results: - DMA start latency (interrupt start latency + DMA configuration) consistently 70us when system not loaded. - DMA start latency up to 4400us when system loaded. 2. Sending 40 bytes packet at 8mS interval. Results with load: - Able to observe overruns by running: `watch -n1 cat /proc/tty/driver/IMX-uart` Tested-by: Peter Senna Tschudin <peter.senna@collabora.com> Acked-by: Peter Senna Tschudin <peter.senna@collabora.com> Signed-off-by: Nandor Han <nandor.han@ge.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-08 19:38:27 +07:00
/*
* The state-residue variable represents the empty space
* relative to the entire buffer. Taking this in consideration
* the head is always calculated base on the buffer total
* length - DMA transaction residue. The UART script from the
* SDMA firmware will jump to the next buffer descriptor,
* once a DMA transaction if finalized (IMX53 RM - A.4.1.2.4).
* Taking this in consideration the tail is always at the
* beginning of the buffer descriptor that contains the head.
*/
serial: imx-serial - update UART IMX driver to use cyclic DMA The IMX UART has a 32 bytes HW buffer which can be filled up in 2777us at 115200 baud or 80us at 4Mbaud (supported by IMX53). Taking this in consideration there is a good probability to lose data because of the DMA startup latency. Our tests (explained below) indicates a latency up to 4400us when creating interrupt load and ~70us without. When creating interrupt load I was able to see continuous overrun errors by checking serial driver statistics using the command: `cat /proc/tty/driver/IMX-uart`. Replace manual restart of DMA with cyclic DMA to eliminate data loss due to DMA engine startup latency (similar approch to atmel_serial.c driver). As result the DMA engine will start on the first serial data transfer and stops only when serial port is closed. Tests environment: Using the m53evk board I have used a GPIO for profiling the IMX serial driver. - The RX line and GPIO were connected to oscilloscope. - Run a small test program on the m53evk board that will only open and read data from ttymxc2 port. - Connect the ttymxc2 port to my laptop using a USB serial converter where another test program is running, able to send configurable packet lengths and intervals. - Serial ports configured at 115200 8N1. - Interrupts load created by disconnecting/connecting (3s interval) a USB hub, using a digital switch, with 4 USB devices (USB-Serial converter, USB SD card, etc) connected. (around 160 interrupts/second generated) - The GPIO was toggled HI in the `imx_int` when USR1_RRDY or USR1_AGTIM events are received and toggled back, once the DMA configuration is finalized, at the end of `imx_dma_rxint`. Measurements: The measurements were done from the end of the last byte (RX line) until the GPIO was toggled back LOW. Note: The GPIO toggling was done using `gpiod_set_value` method. Tests performed: 1. Sending 9 bytes packets at 8ms interval. Having the 9 bytes packets will activate the RRDY threshold event and IMX serial interrupt called. Results: - DMA start latency (interrupt start latency + DMA configuration) consistently 70us when system not loaded. - DMA start latency up to 4400us when system loaded. 2. Sending 40 bytes packet at 8mS interval. Results with load: - Able to observe overruns by running: `watch -n1 cat /proc/tty/driver/IMX-uart` Tested-by: Peter Senna Tschudin <peter.senna@collabora.com> Acked-by: Peter Senna Tschudin <peter.senna@collabora.com> Signed-off-by: Nandor Han <nandor.han@ge.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-08 19:38:27 +07:00
/* Calculate the head */
rx_ring->head = sg_dma_len(sgl) - state.residue;
/* Calculate the tail. */
bd_size = sg_dma_len(sgl) / sport->rx_periods;
rx_ring->tail = ((rx_ring->head-1) / bd_size) * bd_size;
if (rx_ring->head <= sg_dma_len(sgl) &&
rx_ring->head > rx_ring->tail) {
/* Move data from tail to head */
r_bytes = rx_ring->head - rx_ring->tail;
/* CPU claims ownership of RX DMA buffer */
dma_sync_sg_for_cpu(sport->port.dev, sgl, 1,
DMA_FROM_DEVICE);
w_bytes = tty_insert_flip_string(port,
sport->rx_buf + rx_ring->tail, r_bytes);
/* UART retrieves ownership of RX DMA buffer */
dma_sync_sg_for_device(sport->port.dev, sgl, 1,
DMA_FROM_DEVICE);
if (w_bytes != r_bytes)
sport->port.icount.buf_overrun++;
serial: imx-serial - update UART IMX driver to use cyclic DMA The IMX UART has a 32 bytes HW buffer which can be filled up in 2777us at 115200 baud or 80us at 4Mbaud (supported by IMX53). Taking this in consideration there is a good probability to lose data because of the DMA startup latency. Our tests (explained below) indicates a latency up to 4400us when creating interrupt load and ~70us without. When creating interrupt load I was able to see continuous overrun errors by checking serial driver statistics using the command: `cat /proc/tty/driver/IMX-uart`. Replace manual restart of DMA with cyclic DMA to eliminate data loss due to DMA engine startup latency (similar approch to atmel_serial.c driver). As result the DMA engine will start on the first serial data transfer and stops only when serial port is closed. Tests environment: Using the m53evk board I have used a GPIO for profiling the IMX serial driver. - The RX line and GPIO were connected to oscilloscope. - Run a small test program on the m53evk board that will only open and read data from ttymxc2 port. - Connect the ttymxc2 port to my laptop using a USB serial converter where another test program is running, able to send configurable packet lengths and intervals. - Serial ports configured at 115200 8N1. - Interrupts load created by disconnecting/connecting (3s interval) a USB hub, using a digital switch, with 4 USB devices (USB-Serial converter, USB SD card, etc) connected. (around 160 interrupts/second generated) - The GPIO was toggled HI in the `imx_int` when USR1_RRDY or USR1_AGTIM events are received and toggled back, once the DMA configuration is finalized, at the end of `imx_dma_rxint`. Measurements: The measurements were done from the end of the last byte (RX line) until the GPIO was toggled back LOW. Note: The GPIO toggling was done using `gpiod_set_value` method. Tests performed: 1. Sending 9 bytes packets at 8ms interval. Having the 9 bytes packets will activate the RRDY threshold event and IMX serial interrupt called. Results: - DMA start latency (interrupt start latency + DMA configuration) consistently 70us when system not loaded. - DMA start latency up to 4400us when system loaded. 2. Sending 40 bytes packet at 8mS interval. Results with load: - Able to observe overruns by running: `watch -n1 cat /proc/tty/driver/IMX-uart` Tested-by: Peter Senna Tschudin <peter.senna@collabora.com> Acked-by: Peter Senna Tschudin <peter.senna@collabora.com> Signed-off-by: Nandor Han <nandor.han@ge.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-08 19:38:27 +07:00
sport->port.icount.rx += w_bytes;
} else {
WARN_ON(rx_ring->head > sg_dma_len(sgl));
WARN_ON(rx_ring->head <= rx_ring->tail);
}
}
serial: imx-serial - update UART IMX driver to use cyclic DMA The IMX UART has a 32 bytes HW buffer which can be filled up in 2777us at 115200 baud or 80us at 4Mbaud (supported by IMX53). Taking this in consideration there is a good probability to lose data because of the DMA startup latency. Our tests (explained below) indicates a latency up to 4400us when creating interrupt load and ~70us without. When creating interrupt load I was able to see continuous overrun errors by checking serial driver statistics using the command: `cat /proc/tty/driver/IMX-uart`. Replace manual restart of DMA with cyclic DMA to eliminate data loss due to DMA engine startup latency (similar approch to atmel_serial.c driver). As result the DMA engine will start on the first serial data transfer and stops only when serial port is closed. Tests environment: Using the m53evk board I have used a GPIO for profiling the IMX serial driver. - The RX line and GPIO were connected to oscilloscope. - Run a small test program on the m53evk board that will only open and read data from ttymxc2 port. - Connect the ttymxc2 port to my laptop using a USB serial converter where another test program is running, able to send configurable packet lengths and intervals. - Serial ports configured at 115200 8N1. - Interrupts load created by disconnecting/connecting (3s interval) a USB hub, using a digital switch, with 4 USB devices (USB-Serial converter, USB SD card, etc) connected. (around 160 interrupts/second generated) - The GPIO was toggled HI in the `imx_int` when USR1_RRDY or USR1_AGTIM events are received and toggled back, once the DMA configuration is finalized, at the end of `imx_dma_rxint`. Measurements: The measurements were done from the end of the last byte (RX line) until the GPIO was toggled back LOW. Note: The GPIO toggling was done using `gpiod_set_value` method. Tests performed: 1. Sending 9 bytes packets at 8ms interval. Having the 9 bytes packets will activate the RRDY threshold event and IMX serial interrupt called. Results: - DMA start latency (interrupt start latency + DMA configuration) consistently 70us when system not loaded. - DMA start latency up to 4400us when system loaded. 2. Sending 40 bytes packet at 8mS interval. Results with load: - Able to observe overruns by running: `watch -n1 cat /proc/tty/driver/IMX-uart` Tested-by: Peter Senna Tschudin <peter.senna@collabora.com> Acked-by: Peter Senna Tschudin <peter.senna@collabora.com> Signed-off-by: Nandor Han <nandor.han@ge.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-08 19:38:27 +07:00
if (w_bytes) {
tty_flip_buffer_push(port);
dev_dbg(sport->port.dev, "We get %d bytes.\n", w_bytes);
}
}
/* RX DMA buffer periods */
#define RX_DMA_PERIODS 4
static int start_rx_dma(struct imx_port *sport)
{
struct scatterlist *sgl = &sport->rx_sgl;
struct dma_chan *chan = sport->dma_chan_rx;
struct device *dev = sport->port.dev;
struct dma_async_tx_descriptor *desc;
int ret;
serial: imx-serial - update UART IMX driver to use cyclic DMA The IMX UART has a 32 bytes HW buffer which can be filled up in 2777us at 115200 baud or 80us at 4Mbaud (supported by IMX53). Taking this in consideration there is a good probability to lose data because of the DMA startup latency. Our tests (explained below) indicates a latency up to 4400us when creating interrupt load and ~70us without. When creating interrupt load I was able to see continuous overrun errors by checking serial driver statistics using the command: `cat /proc/tty/driver/IMX-uart`. Replace manual restart of DMA with cyclic DMA to eliminate data loss due to DMA engine startup latency (similar approch to atmel_serial.c driver). As result the DMA engine will start on the first serial data transfer and stops only when serial port is closed. Tests environment: Using the m53evk board I have used a GPIO for profiling the IMX serial driver. - The RX line and GPIO were connected to oscilloscope. - Run a small test program on the m53evk board that will only open and read data from ttymxc2 port. - Connect the ttymxc2 port to my laptop using a USB serial converter where another test program is running, able to send configurable packet lengths and intervals. - Serial ports configured at 115200 8N1. - Interrupts load created by disconnecting/connecting (3s interval) a USB hub, using a digital switch, with 4 USB devices (USB-Serial converter, USB SD card, etc) connected. (around 160 interrupts/second generated) - The GPIO was toggled HI in the `imx_int` when USR1_RRDY or USR1_AGTIM events are received and toggled back, once the DMA configuration is finalized, at the end of `imx_dma_rxint`. Measurements: The measurements were done from the end of the last byte (RX line) until the GPIO was toggled back LOW. Note: The GPIO toggling was done using `gpiod_set_value` method. Tests performed: 1. Sending 9 bytes packets at 8ms interval. Having the 9 bytes packets will activate the RRDY threshold event and IMX serial interrupt called. Results: - DMA start latency (interrupt start latency + DMA configuration) consistently 70us when system not loaded. - DMA start latency up to 4400us when system loaded. 2. Sending 40 bytes packet at 8mS interval. Results with load: - Able to observe overruns by running: `watch -n1 cat /proc/tty/driver/IMX-uart` Tested-by: Peter Senna Tschudin <peter.senna@collabora.com> Acked-by: Peter Senna Tschudin <peter.senna@collabora.com> Signed-off-by: Nandor Han <nandor.han@ge.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-08 19:38:27 +07:00
sport->rx_ring.head = 0;
sport->rx_ring.tail = 0;
sport->rx_periods = RX_DMA_PERIODS;
serial: imx-serial - update UART IMX driver to use cyclic DMA The IMX UART has a 32 bytes HW buffer which can be filled up in 2777us at 115200 baud or 80us at 4Mbaud (supported by IMX53). Taking this in consideration there is a good probability to lose data because of the DMA startup latency. Our tests (explained below) indicates a latency up to 4400us when creating interrupt load and ~70us without. When creating interrupt load I was able to see continuous overrun errors by checking serial driver statistics using the command: `cat /proc/tty/driver/IMX-uart`. Replace manual restart of DMA with cyclic DMA to eliminate data loss due to DMA engine startup latency (similar approch to atmel_serial.c driver). As result the DMA engine will start on the first serial data transfer and stops only when serial port is closed. Tests environment: Using the m53evk board I have used a GPIO for profiling the IMX serial driver. - The RX line and GPIO were connected to oscilloscope. - Run a small test program on the m53evk board that will only open and read data from ttymxc2 port. - Connect the ttymxc2 port to my laptop using a USB serial converter where another test program is running, able to send configurable packet lengths and intervals. - Serial ports configured at 115200 8N1. - Interrupts load created by disconnecting/connecting (3s interval) a USB hub, using a digital switch, with 4 USB devices (USB-Serial converter, USB SD card, etc) connected. (around 160 interrupts/second generated) - The GPIO was toggled HI in the `imx_int` when USR1_RRDY or USR1_AGTIM events are received and toggled back, once the DMA configuration is finalized, at the end of `imx_dma_rxint`. Measurements: The measurements were done from the end of the last byte (RX line) until the GPIO was toggled back LOW. Note: The GPIO toggling was done using `gpiod_set_value` method. Tests performed: 1. Sending 9 bytes packets at 8ms interval. Having the 9 bytes packets will activate the RRDY threshold event and IMX serial interrupt called. Results: - DMA start latency (interrupt start latency + DMA configuration) consistently 70us when system not loaded. - DMA start latency up to 4400us when system loaded. 2. Sending 40 bytes packet at 8mS interval. Results with load: - Able to observe overruns by running: `watch -n1 cat /proc/tty/driver/IMX-uart` Tested-by: Peter Senna Tschudin <peter.senna@collabora.com> Acked-by: Peter Senna Tschudin <peter.senna@collabora.com> Signed-off-by: Nandor Han <nandor.han@ge.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-08 19:38:27 +07:00
sg_init_one(sgl, sport->rx_buf, RX_BUF_SIZE);
ret = dma_map_sg(dev, sgl, 1, DMA_FROM_DEVICE);
if (ret == 0) {
dev_err(dev, "DMA mapping error for RX.\n");
return -EINVAL;
}
serial: imx-serial - update UART IMX driver to use cyclic DMA The IMX UART has a 32 bytes HW buffer which can be filled up in 2777us at 115200 baud or 80us at 4Mbaud (supported by IMX53). Taking this in consideration there is a good probability to lose data because of the DMA startup latency. Our tests (explained below) indicates a latency up to 4400us when creating interrupt load and ~70us without. When creating interrupt load I was able to see continuous overrun errors by checking serial driver statistics using the command: `cat /proc/tty/driver/IMX-uart`. Replace manual restart of DMA with cyclic DMA to eliminate data loss due to DMA engine startup latency (similar approch to atmel_serial.c driver). As result the DMA engine will start on the first serial data transfer and stops only when serial port is closed. Tests environment: Using the m53evk board I have used a GPIO for profiling the IMX serial driver. - The RX line and GPIO were connected to oscilloscope. - Run a small test program on the m53evk board that will only open and read data from ttymxc2 port. - Connect the ttymxc2 port to my laptop using a USB serial converter where another test program is running, able to send configurable packet lengths and intervals. - Serial ports configured at 115200 8N1. - Interrupts load created by disconnecting/connecting (3s interval) a USB hub, using a digital switch, with 4 USB devices (USB-Serial converter, USB SD card, etc) connected. (around 160 interrupts/second generated) - The GPIO was toggled HI in the `imx_int` when USR1_RRDY or USR1_AGTIM events are received and toggled back, once the DMA configuration is finalized, at the end of `imx_dma_rxint`. Measurements: The measurements were done from the end of the last byte (RX line) until the GPIO was toggled back LOW. Note: The GPIO toggling was done using `gpiod_set_value` method. Tests performed: 1. Sending 9 bytes packets at 8ms interval. Having the 9 bytes packets will activate the RRDY threshold event and IMX serial interrupt called. Results: - DMA start latency (interrupt start latency + DMA configuration) consistently 70us when system not loaded. - DMA start latency up to 4400us when system loaded. 2. Sending 40 bytes packet at 8mS interval. Results with load: - Able to observe overruns by running: `watch -n1 cat /proc/tty/driver/IMX-uart` Tested-by: Peter Senna Tschudin <peter.senna@collabora.com> Acked-by: Peter Senna Tschudin <peter.senna@collabora.com> Signed-off-by: Nandor Han <nandor.han@ge.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-08 19:38:27 +07:00
desc = dmaengine_prep_dma_cyclic(chan, sg_dma_address(sgl),
sg_dma_len(sgl), sg_dma_len(sgl) / sport->rx_periods,
DMA_DEV_TO_MEM, DMA_PREP_INTERRUPT);
if (!desc) {
dma_unmap_sg(dev, sgl, 1, DMA_FROM_DEVICE);
dev_err(dev, "We cannot prepare for the RX slave dma!\n");
return -EINVAL;
}
desc->callback = dma_rx_callback;
desc->callback_param = sport;
dev_dbg(dev, "RX: prepare for the DMA.\n");
serial: imx-serial - update UART IMX driver to use cyclic DMA The IMX UART has a 32 bytes HW buffer which can be filled up in 2777us at 115200 baud or 80us at 4Mbaud (supported by IMX53). Taking this in consideration there is a good probability to lose data because of the DMA startup latency. Our tests (explained below) indicates a latency up to 4400us when creating interrupt load and ~70us without. When creating interrupt load I was able to see continuous overrun errors by checking serial driver statistics using the command: `cat /proc/tty/driver/IMX-uart`. Replace manual restart of DMA with cyclic DMA to eliminate data loss due to DMA engine startup latency (similar approch to atmel_serial.c driver). As result the DMA engine will start on the first serial data transfer and stops only when serial port is closed. Tests environment: Using the m53evk board I have used a GPIO for profiling the IMX serial driver. - The RX line and GPIO were connected to oscilloscope. - Run a small test program on the m53evk board that will only open and read data from ttymxc2 port. - Connect the ttymxc2 port to my laptop using a USB serial converter where another test program is running, able to send configurable packet lengths and intervals. - Serial ports configured at 115200 8N1. - Interrupts load created by disconnecting/connecting (3s interval) a USB hub, using a digital switch, with 4 USB devices (USB-Serial converter, USB SD card, etc) connected. (around 160 interrupts/second generated) - The GPIO was toggled HI in the `imx_int` when USR1_RRDY or USR1_AGTIM events are received and toggled back, once the DMA configuration is finalized, at the end of `imx_dma_rxint`. Measurements: The measurements were done from the end of the last byte (RX line) until the GPIO was toggled back LOW. Note: The GPIO toggling was done using `gpiod_set_value` method. Tests performed: 1. Sending 9 bytes packets at 8ms interval. Having the 9 bytes packets will activate the RRDY threshold event and IMX serial interrupt called. Results: - DMA start latency (interrupt start latency + DMA configuration) consistently 70us when system not loaded. - DMA start latency up to 4400us when system loaded. 2. Sending 40 bytes packet at 8mS interval. Results with load: - Able to observe overruns by running: `watch -n1 cat /proc/tty/driver/IMX-uart` Tested-by: Peter Senna Tschudin <peter.senna@collabora.com> Acked-by: Peter Senna Tschudin <peter.senna@collabora.com> Signed-off-by: Nandor Han <nandor.han@ge.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-08 19:38:27 +07:00
sport->rx_cookie = dmaengine_submit(desc);
dma_async_issue_pending(chan);
return 0;
}
static void clear_rx_errors(struct imx_port *sport)
{
unsigned int status_usr1, status_usr2;
status_usr1 = readl(sport->port.membase + USR1);
status_usr2 = readl(sport->port.membase + USR2);
if (status_usr2 & USR2_BRCD) {
sport->port.icount.brk++;
writel(USR2_BRCD, sport->port.membase + USR2);
} else if (status_usr1 & USR1_FRAMERR) {
sport->port.icount.frame++;
writel(USR1_FRAMERR, sport->port.membase + USR1);
} else if (status_usr1 & USR1_PARITYERR) {
sport->port.icount.parity++;
writel(USR1_PARITYERR, sport->port.membase + USR1);
}
if (status_usr2 & USR2_ORE) {
sport->port.icount.overrun++;
writel(USR2_ORE, sport->port.membase + USR2);
}
}
#define TXTL_DEFAULT 2 /* reset default */
#define RXTL_DEFAULT 1 /* reset default */
#define TXTL_DMA 8 /* DMA burst setting */
#define RXTL_DMA 9 /* DMA burst setting */
static void imx_setup_ufcr(struct imx_port *sport,
unsigned char txwl, unsigned char rxwl)
{
unsigned int val;
/* set receiver / transmitter trigger level */
val = readl(sport->port.membase + UFCR) & (UFCR_RFDIV | UFCR_DCEDTE);
val |= txwl << UFCR_TXTL_SHF | rxwl;
writel(val, sport->port.membase + UFCR);
}
static void imx_uart_dma_exit(struct imx_port *sport)
{
if (sport->dma_chan_rx) {
dmaengine_terminate_sync(sport->dma_chan_rx);
dma_release_channel(sport->dma_chan_rx);
sport->dma_chan_rx = NULL;
serial: imx-serial - update UART IMX driver to use cyclic DMA The IMX UART has a 32 bytes HW buffer which can be filled up in 2777us at 115200 baud or 80us at 4Mbaud (supported by IMX53). Taking this in consideration there is a good probability to lose data because of the DMA startup latency. Our tests (explained below) indicates a latency up to 4400us when creating interrupt load and ~70us without. When creating interrupt load I was able to see continuous overrun errors by checking serial driver statistics using the command: `cat /proc/tty/driver/IMX-uart`. Replace manual restart of DMA with cyclic DMA to eliminate data loss due to DMA engine startup latency (similar approch to atmel_serial.c driver). As result the DMA engine will start on the first serial data transfer and stops only when serial port is closed. Tests environment: Using the m53evk board I have used a GPIO for profiling the IMX serial driver. - The RX line and GPIO were connected to oscilloscope. - Run a small test program on the m53evk board that will only open and read data from ttymxc2 port. - Connect the ttymxc2 port to my laptop using a USB serial converter where another test program is running, able to send configurable packet lengths and intervals. - Serial ports configured at 115200 8N1. - Interrupts load created by disconnecting/connecting (3s interval) a USB hub, using a digital switch, with 4 USB devices (USB-Serial converter, USB SD card, etc) connected. (around 160 interrupts/second generated) - The GPIO was toggled HI in the `imx_int` when USR1_RRDY or USR1_AGTIM events are received and toggled back, once the DMA configuration is finalized, at the end of `imx_dma_rxint`. Measurements: The measurements were done from the end of the last byte (RX line) until the GPIO was toggled back LOW. Note: The GPIO toggling was done using `gpiod_set_value` method. Tests performed: 1. Sending 9 bytes packets at 8ms interval. Having the 9 bytes packets will activate the RRDY threshold event and IMX serial interrupt called. Results: - DMA start latency (interrupt start latency + DMA configuration) consistently 70us when system not loaded. - DMA start latency up to 4400us when system loaded. 2. Sending 40 bytes packet at 8mS interval. Results with load: - Able to observe overruns by running: `watch -n1 cat /proc/tty/driver/IMX-uart` Tested-by: Peter Senna Tschudin <peter.senna@collabora.com> Acked-by: Peter Senna Tschudin <peter.senna@collabora.com> Signed-off-by: Nandor Han <nandor.han@ge.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-08 19:38:27 +07:00
sport->rx_cookie = -EINVAL;
kfree(sport->rx_buf);
sport->rx_buf = NULL;
}
if (sport->dma_chan_tx) {
dmaengine_terminate_sync(sport->dma_chan_tx);
dma_release_channel(sport->dma_chan_tx);
sport->dma_chan_tx = NULL;
}
sport->dma_is_inited = 0;
}
static int imx_uart_dma_init(struct imx_port *sport)
{
struct dma_slave_config slave_config = {};
struct device *dev = sport->port.dev;
int ret;
/* Prepare for RX : */
sport->dma_chan_rx = dma_request_slave_channel(dev, "rx");
if (!sport->dma_chan_rx) {
dev_dbg(dev, "cannot get the DMA channel.\n");
ret = -EINVAL;
goto err;
}
slave_config.direction = DMA_DEV_TO_MEM;
slave_config.src_addr = sport->port.mapbase + URXD0;
slave_config.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
/* one byte less than the watermark level to enable the aging timer */
slave_config.src_maxburst = RXTL_DMA - 1;
ret = dmaengine_slave_config(sport->dma_chan_rx, &slave_config);
if (ret) {
dev_err(dev, "error in RX dma configuration.\n");
goto err;
}
sport->rx_buf = kzalloc(PAGE_SIZE, GFP_KERNEL);
if (!sport->rx_buf) {
ret = -ENOMEM;
goto err;
}
serial: imx-serial - update UART IMX driver to use cyclic DMA The IMX UART has a 32 bytes HW buffer which can be filled up in 2777us at 115200 baud or 80us at 4Mbaud (supported by IMX53). Taking this in consideration there is a good probability to lose data because of the DMA startup latency. Our tests (explained below) indicates a latency up to 4400us when creating interrupt load and ~70us without. When creating interrupt load I was able to see continuous overrun errors by checking serial driver statistics using the command: `cat /proc/tty/driver/IMX-uart`. Replace manual restart of DMA with cyclic DMA to eliminate data loss due to DMA engine startup latency (similar approch to atmel_serial.c driver). As result the DMA engine will start on the first serial data transfer and stops only when serial port is closed. Tests environment: Using the m53evk board I have used a GPIO for profiling the IMX serial driver. - The RX line and GPIO were connected to oscilloscope. - Run a small test program on the m53evk board that will only open and read data from ttymxc2 port. - Connect the ttymxc2 port to my laptop using a USB serial converter where another test program is running, able to send configurable packet lengths and intervals. - Serial ports configured at 115200 8N1. - Interrupts load created by disconnecting/connecting (3s interval) a USB hub, using a digital switch, with 4 USB devices (USB-Serial converter, USB SD card, etc) connected. (around 160 interrupts/second generated) - The GPIO was toggled HI in the `imx_int` when USR1_RRDY or USR1_AGTIM events are received and toggled back, once the DMA configuration is finalized, at the end of `imx_dma_rxint`. Measurements: The measurements were done from the end of the last byte (RX line) until the GPIO was toggled back LOW. Note: The GPIO toggling was done using `gpiod_set_value` method. Tests performed: 1. Sending 9 bytes packets at 8ms interval. Having the 9 bytes packets will activate the RRDY threshold event and IMX serial interrupt called. Results: - DMA start latency (interrupt start latency + DMA configuration) consistently 70us when system not loaded. - DMA start latency up to 4400us when system loaded. 2. Sending 40 bytes packet at 8mS interval. Results with load: - Able to observe overruns by running: `watch -n1 cat /proc/tty/driver/IMX-uart` Tested-by: Peter Senna Tschudin <peter.senna@collabora.com> Acked-by: Peter Senna Tschudin <peter.senna@collabora.com> Signed-off-by: Nandor Han <nandor.han@ge.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-08 19:38:27 +07:00
sport->rx_ring.buf = sport->rx_buf;
/* Prepare for TX : */
sport->dma_chan_tx = dma_request_slave_channel(dev, "tx");
if (!sport->dma_chan_tx) {
dev_err(dev, "cannot get the TX DMA channel!\n");
ret = -EINVAL;
goto err;
}
slave_config.direction = DMA_MEM_TO_DEV;
slave_config.dst_addr = sport->port.mapbase + URTX0;
slave_config.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
slave_config.dst_maxburst = TXTL_DMA;
ret = dmaengine_slave_config(sport->dma_chan_tx, &slave_config);
if (ret) {
dev_err(dev, "error in TX dma configuration.");
goto err;
}
sport->dma_is_inited = 1;
return 0;
err:
imx_uart_dma_exit(sport);
return ret;
}
static void imx_enable_dma(struct imx_port *sport)
{
unsigned long temp;
init_waitqueue_head(&sport->dma_wait);
/* set UCR1 */
temp = readl(sport->port.membase + UCR1);
temp |= UCR1_RDMAEN | UCR1_TDMAEN | UCR1_ATDMAEN;
writel(temp, sport->port.membase + UCR1);
temp = readl(sport->port.membase + UCR2);
temp |= UCR2_ATEN;
writel(temp, sport->port.membase + UCR2);
imx_setup_ufcr(sport, TXTL_DMA, RXTL_DMA);
sport->dma_is_enabled = 1;
}
static void imx_disable_dma(struct imx_port *sport)
{
unsigned long temp;
/* clear UCR1 */
temp = readl(sport->port.membase + UCR1);
temp &= ~(UCR1_RDMAEN | UCR1_TDMAEN | UCR1_ATDMAEN);
writel(temp, sport->port.membase + UCR1);
/* clear UCR2 */
temp = readl(sport->port.membase + UCR2);
temp &= ~(UCR2_CTSC | UCR2_CTS | UCR2_ATEN);
writel(temp, sport->port.membase + UCR2);
imx_setup_ufcr(sport, TXTL_DEFAULT, RXTL_DEFAULT);
sport->dma_is_enabled = 0;
}
/* half the RX buffer size */
#define CTSTL 16
static int imx_startup(struct uart_port *port)
{
struct imx_port *sport = (struct imx_port *)port;
int retval, i;
unsigned long flags, temp;
retval = clk_prepare_enable(sport->clk_per);
if (retval)
return retval;
retval = clk_prepare_enable(sport->clk_ipg);
if (retval) {
clk_disable_unprepare(sport->clk_per);
return retval;
}
imx_setup_ufcr(sport, TXTL_DEFAULT, RXTL_DEFAULT);
/* disable the DREN bit (Data Ready interrupt enable) before
* requesting IRQs
*/
temp = readl(sport->port.membase + UCR4);
/* set the trigger level for CTS */
temp &= ~(UCR4_CTSTL_MASK << UCR4_CTSTL_SHF);
temp |= CTSTL << UCR4_CTSTL_SHF;
writel(temp & ~UCR4_DREN, sport->port.membase + UCR4);
/* Can we enable the DMA support? */
if (!uart_console(port) && !sport->dma_is_inited)
imx_uart_dma_init(sport);
spin_lock_irqsave(&sport->port.lock, flags);
/* Reset fifo's and state machines */
i = 100;
temp = readl(sport->port.membase + UCR2);
temp &= ~UCR2_SRST;
writel(temp, sport->port.membase + UCR2);
while (!(readl(sport->port.membase + UCR2) & UCR2_SRST) && (--i > 0))
udelay(1);
/*
* Finally, clear and enable interrupts
*/
writel(USR1_RTSD | USR1_DTRD, sport->port.membase + USR1);
writel(USR2_ORE, sport->port.membase + USR2);
if (sport->dma_is_inited && !sport->dma_is_enabled)
imx_enable_dma(sport);
temp = readl(sport->port.membase + UCR1);
temp |= UCR1_RRDYEN | UCR1_UARTEN;
if (sport->have_rtscts)
temp |= UCR1_RTSDEN;
writel(temp, sport->port.membase + UCR1);
temp = readl(sport->port.membase + UCR4);
temp |= UCR4_OREN;
writel(temp, sport->port.membase + UCR4);
temp = readl(sport->port.membase + UCR2);
temp |= (UCR2_RXEN | UCR2_TXEN);
if (!sport->have_rtscts)
temp |= UCR2_IRTS;
/*
* make sure the edge sensitive RTS-irq is disabled,
* we're using RTSD instead.
*/
if (!is_imx1_uart(sport))
temp &= ~UCR2_RTSEN;
writel(temp, sport->port.membase + UCR2);
if (!is_imx1_uart(sport)) {
temp = readl(sport->port.membase + UCR3);
temp |= UCR3_DTRDEN | UCR3_RI | UCR3_DCD;
if (sport->dte_mode)
/* disable broken interrupts */
temp &= ~(UCR3_RI | UCR3_DCD);
writel(temp, sport->port.membase + UCR3);
}
/*
* Enable modem status interrupts
*/
imx_enable_ms(&sport->port);
/*
* Start RX DMA immediately instead of waiting for RX FIFO interrupts.
* In our iMX53 the average delay for the first reception dropped from
* approximately 35000 microseconds to 1000 microseconds.
*/
if (sport->dma_is_enabled) {
imx_disable_rx_int(sport);
start_rx_dma(sport);
}
spin_unlock_irqrestore(&sport->port.lock, flags);
return 0;
}
static void imx_shutdown(struct uart_port *port)
{
struct imx_port *sport = (struct imx_port *)port;
unsigned long temp;
unsigned long flags;
if (sport->dma_is_enabled) {
serial: imx-serial - update UART IMX driver to use cyclic DMA The IMX UART has a 32 bytes HW buffer which can be filled up in 2777us at 115200 baud or 80us at 4Mbaud (supported by IMX53). Taking this in consideration there is a good probability to lose data because of the DMA startup latency. Our tests (explained below) indicates a latency up to 4400us when creating interrupt load and ~70us without. When creating interrupt load I was able to see continuous overrun errors by checking serial driver statistics using the command: `cat /proc/tty/driver/IMX-uart`. Replace manual restart of DMA with cyclic DMA to eliminate data loss due to DMA engine startup latency (similar approch to atmel_serial.c driver). As result the DMA engine will start on the first serial data transfer and stops only when serial port is closed. Tests environment: Using the m53evk board I have used a GPIO for profiling the IMX serial driver. - The RX line and GPIO were connected to oscilloscope. - Run a small test program on the m53evk board that will only open and read data from ttymxc2 port. - Connect the ttymxc2 port to my laptop using a USB serial converter where another test program is running, able to send configurable packet lengths and intervals. - Serial ports configured at 115200 8N1. - Interrupts load created by disconnecting/connecting (3s interval) a USB hub, using a digital switch, with 4 USB devices (USB-Serial converter, USB SD card, etc) connected. (around 160 interrupts/second generated) - The GPIO was toggled HI in the `imx_int` when USR1_RRDY or USR1_AGTIM events are received and toggled back, once the DMA configuration is finalized, at the end of `imx_dma_rxint`. Measurements: The measurements were done from the end of the last byte (RX line) until the GPIO was toggled back LOW. Note: The GPIO toggling was done using `gpiod_set_value` method. Tests performed: 1. Sending 9 bytes packets at 8ms interval. Having the 9 bytes packets will activate the RRDY threshold event and IMX serial interrupt called. Results: - DMA start latency (interrupt start latency + DMA configuration) consistently 70us when system not loaded. - DMA start latency up to 4400us when system loaded. 2. Sending 40 bytes packet at 8mS interval. Results with load: - Able to observe overruns by running: `watch -n1 cat /proc/tty/driver/IMX-uart` Tested-by: Peter Senna Tschudin <peter.senna@collabora.com> Acked-by: Peter Senna Tschudin <peter.senna@collabora.com> Signed-off-by: Nandor Han <nandor.han@ge.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-08 19:38:27 +07:00
sport->dma_is_rxing = 0;
sport->dma_is_txing = 0;
dmaengine_terminate_sync(sport->dma_chan_tx);
dmaengine_terminate_sync(sport->dma_chan_rx);
spin_lock_irqsave(&sport->port.lock, flags);
imx_stop_tx(port);
imx_stop_rx(port);
imx_disable_dma(sport);
spin_unlock_irqrestore(&sport->port.lock, flags);
imx_uart_dma_exit(sport);
}
mctrl_gpio_disable_ms(sport->gpios);
spin_lock_irqsave(&sport->port.lock, flags);
temp = readl(sport->port.membase + UCR2);
temp &= ~(UCR2_TXEN);
writel(temp, sport->port.membase + UCR2);
spin_unlock_irqrestore(&sport->port.lock, flags);
/*
* Stop our timer.
*/
del_timer_sync(&sport->timer);
/*
* Disable all interrupts, port and break condition.
*/
spin_lock_irqsave(&sport->port.lock, flags);
temp = readl(sport->port.membase + UCR1);
temp &= ~(UCR1_TXMPTYEN | UCR1_RRDYEN | UCR1_RTSDEN | UCR1_UARTEN);
writel(temp, sport->port.membase + UCR1);
spin_unlock_irqrestore(&sport->port.lock, flags);
clk_disable_unprepare(sport->clk_per);
clk_disable_unprepare(sport->clk_ipg);
}
static void imx_flush_buffer(struct uart_port *port)
{
struct imx_port *sport = (struct imx_port *)port;
struct scatterlist *sgl = &sport->tx_sgl[0];
unsigned long temp;
int i = 100, ubir, ubmr, uts;
if (!sport->dma_chan_tx)
return;
sport->tx_bytes = 0;
dmaengine_terminate_all(sport->dma_chan_tx);
if (sport->dma_is_txing) {
dma_unmap_sg(sport->port.dev, sgl, sport->dma_tx_nents,
DMA_TO_DEVICE);
temp = readl(sport->port.membase + UCR1);
temp &= ~UCR1_TDMAEN;
writel(temp, sport->port.membase + UCR1);
sport->dma_is_txing = false;
}
/*
* According to the Reference Manual description of the UART SRST bit:
* "Reset the transmit and receive state machines,
* all FIFOs and register USR1, USR2, UBIR, UBMR, UBRC, URXD, UTXD
* and UTS[6-3]". As we don't need to restore the old values from
* USR1, USR2, URXD, UTXD, only save/restore the other four registers
*/
ubir = readl(sport->port.membase + UBIR);
ubmr = readl(sport->port.membase + UBMR);
uts = readl(sport->port.membase + IMX21_UTS);
temp = readl(sport->port.membase + UCR2);
temp &= ~UCR2_SRST;
writel(temp, sport->port.membase + UCR2);
while (!(readl(sport->port.membase + UCR2) & UCR2_SRST) && (--i > 0))
udelay(1);
/* Restore the registers */
writel(ubir, sport->port.membase + UBIR);
writel(ubmr, sport->port.membase + UBMR);
writel(uts, sport->port.membase + IMX21_UTS);
}
static void
imx_set_termios(struct uart_port *port, struct ktermios *termios,
struct ktermios *old)
{
struct imx_port *sport = (struct imx_port *)port;
unsigned long flags;
unsigned long ucr2, old_ucr1, old_ucr2;
unsigned int baud, quot;
unsigned int old_csize = old ? old->c_cflag & CSIZE : CS8;
unsigned long div, ufcr;
unsigned long num, denom;
uint64_t tdiv64;
/*
* We only support CS7 and CS8.
*/
while ((termios->c_cflag & CSIZE) != CS7 &&
(termios->c_cflag & CSIZE) != CS8) {
termios->c_cflag &= ~CSIZE;
termios->c_cflag |= old_csize;
old_csize = CS8;
}
if ((termios->c_cflag & CSIZE) == CS8)
ucr2 = UCR2_WS | UCR2_SRST | UCR2_IRTS;
else
ucr2 = UCR2_SRST | UCR2_IRTS;
if (termios->c_cflag & CRTSCTS) {
if (sport->have_rtscts) {
ucr2 &= ~UCR2_IRTS;
if (port->rs485.flags & SER_RS485_ENABLED) {
/*
* RTS is mandatory for rs485 operation, so keep
* it under manual control and keep transmitter
* disabled.
*/
if (port->rs485.flags &
SER_RS485_RTS_AFTER_SEND)
imx_port_rts_active(sport, &ucr2);
else
imx_port_rts_inactive(sport, &ucr2);
} else {
imx_port_rts_auto(sport, &ucr2);
}
} else {
termios->c_cflag &= ~CRTSCTS;
}
} else if (port->rs485.flags & SER_RS485_ENABLED) {
/* disable transmitter */
if (port->rs485.flags & SER_RS485_RTS_AFTER_SEND)
imx_port_rts_active(sport, &ucr2);
else
imx_port_rts_inactive(sport, &ucr2);
}
if (termios->c_cflag & CSTOPB)
ucr2 |= UCR2_STPB;
if (termios->c_cflag & PARENB) {
ucr2 |= UCR2_PREN;
if (termios->c_cflag & PARODD)
ucr2 |= UCR2_PROE;
}
del_timer_sync(&sport->timer);
/*
* Ask the core to calculate the divisor for us.
*/
baud = uart_get_baud_rate(port, termios, old, 50, port->uartclk / 16);
quot = uart_get_divisor(port, baud);
spin_lock_irqsave(&sport->port.lock, flags);
sport->port.read_status_mask = 0;
if (termios->c_iflag & INPCK)
sport->port.read_status_mask |= (URXD_FRMERR | URXD_PRERR);
if (termios->c_iflag & (BRKINT | PARMRK))
sport->port.read_status_mask |= URXD_BRK;
/*
* Characters to ignore
*/
sport->port.ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
sport->port.ignore_status_mask |= URXD_PRERR | URXD_FRMERR;
if (termios->c_iflag & IGNBRK) {
sport->port.ignore_status_mask |= URXD_BRK;
/*
* If we're ignoring parity and break indicators,
* ignore overruns too (for real raw support).
*/
if (termios->c_iflag & IGNPAR)
sport->port.ignore_status_mask |= URXD_OVRRUN;
}
if ((termios->c_cflag & CREAD) == 0)
sport->port.ignore_status_mask |= URXD_DUMMY_READ;
/*
* Update the per-port timeout.
*/
uart_update_timeout(port, termios->c_cflag, baud);
/*
* disable interrupts and drain transmitter
*/
old_ucr1 = readl(sport->port.membase + UCR1);
writel(old_ucr1 & ~(UCR1_TXMPTYEN | UCR1_RRDYEN | UCR1_RTSDEN),
sport->port.membase + UCR1);
while (!(readl(sport->port.membase + USR2) & USR2_TXDC))
barrier();
/* then, disable everything */
old_ucr2 = readl(sport->port.membase + UCR2);
writel(old_ucr2 & ~(UCR2_TXEN | UCR2_RXEN),
sport->port.membase + UCR2);
old_ucr2 &= (UCR2_TXEN | UCR2_RXEN | UCR2_ATEN);
/* custom-baudrate handling */
div = sport->port.uartclk / (baud * 16);
if (baud == 38400 && quot != div)
baud = sport->port.uartclk / (quot * 16);
div = sport->port.uartclk / (baud * 16);
if (div > 7)
div = 7;
if (!div)
div = 1;
rational_best_approximation(16 * div * baud, sport->port.uartclk,
1 << 16, 1 << 16, &num, &denom);
tdiv64 = sport->port.uartclk;
tdiv64 *= num;
do_div(tdiv64, denom * 16 * div);
tty_termios_encode_baud_rate(termios,
(speed_t)tdiv64, (speed_t)tdiv64);
num -= 1;
denom -= 1;
ufcr = readl(sport->port.membase + UFCR);
ufcr = (ufcr & (~UFCR_RFDIV)) | UFCR_RFDIV_REG(div);
writel(ufcr, sport->port.membase + UFCR);
writel(num, sport->port.membase + UBIR);
writel(denom, sport->port.membase + UBMR);
if (!is_imx1_uart(sport))
writel(sport->port.uartclk / div / 1000,
sport->port.membase + IMX21_ONEMS);
writel(old_ucr1, sport->port.membase + UCR1);
/* set the parity, stop bits and data size */
writel(ucr2 | old_ucr2, sport->port.membase + UCR2);
if (UART_ENABLE_MS(&sport->port, termios->c_cflag))
imx_enable_ms(&sport->port);
spin_unlock_irqrestore(&sport->port.lock, flags);
}
static const char *imx_type(struct uart_port *port)
{
struct imx_port *sport = (struct imx_port *)port;
return sport->port.type == PORT_IMX ? "IMX" : NULL;
}
/*
* Configure/autoconfigure the port.
*/
static void imx_config_port(struct uart_port *port, int flags)
{
struct imx_port *sport = (struct imx_port *)port;
if (flags & UART_CONFIG_TYPE)
sport->port.type = PORT_IMX;
}
/*
* Verify the new serial_struct (for TIOCSSERIAL).
* The only change we allow are to the flags and type, and
* even then only between PORT_IMX and PORT_UNKNOWN
*/
static int
imx_verify_port(struct uart_port *port, struct serial_struct *ser)
{
struct imx_port *sport = (struct imx_port *)port;
int ret = 0;
if (ser->type != PORT_UNKNOWN && ser->type != PORT_IMX)
ret = -EINVAL;
if (sport->port.irq != ser->irq)
ret = -EINVAL;
if (ser->io_type != UPIO_MEM)
ret = -EINVAL;
if (sport->port.uartclk / 16 != ser->baud_base)
ret = -EINVAL;
if (sport->port.mapbase != (unsigned long)ser->iomem_base)
ret = -EINVAL;
if (sport->port.iobase != ser->port)
ret = -EINVAL;
if (ser->hub6 != 0)
ret = -EINVAL;
return ret;
}
#if defined(CONFIG_CONSOLE_POLL)
static int imx_poll_init(struct uart_port *port)
{
struct imx_port *sport = (struct imx_port *)port;
unsigned long flags;
unsigned long temp;
int retval;
retval = clk_prepare_enable(sport->clk_ipg);
if (retval)
return retval;
retval = clk_prepare_enable(sport->clk_per);
if (retval)
clk_disable_unprepare(sport->clk_ipg);
imx_setup_ufcr(sport, TXTL_DEFAULT, RXTL_DEFAULT);
spin_lock_irqsave(&sport->port.lock, flags);
temp = readl(sport->port.membase + UCR1);
if (is_imx1_uart(sport))
temp |= IMX1_UCR1_UARTCLKEN;
temp |= UCR1_UARTEN | UCR1_RRDYEN;
temp &= ~(UCR1_TXMPTYEN | UCR1_RTSDEN);
writel(temp, sport->port.membase + UCR1);
temp = readl(sport->port.membase + UCR2);
temp |= UCR2_RXEN;
writel(temp, sport->port.membase + UCR2);
spin_unlock_irqrestore(&sport->port.lock, flags);
return 0;
}
static int imx_poll_get_char(struct uart_port *port)
{
if (!(readl_relaxed(port->membase + USR2) & USR2_RDR))
return NO_POLL_CHAR;
return readl_relaxed(port->membase + URXD0) & URXD_RX_DATA;
}
static void imx_poll_put_char(struct uart_port *port, unsigned char c)
{
unsigned int status;
/* drain */
do {
status = readl_relaxed(port->membase + USR1);
} while (~status & USR1_TRDY);
/* write */
writel_relaxed(c, port->membase + URTX0);
/* flush */
do {
status = readl_relaxed(port->membase + USR2);
} while (~status & USR2_TXDC);
}
#endif
static int imx_rs485_config(struct uart_port *port,
struct serial_rs485 *rs485conf)
{
struct imx_port *sport = (struct imx_port *)port;
unsigned long temp;
/* unimplemented */
rs485conf->delay_rts_before_send = 0;
rs485conf->delay_rts_after_send = 0;
/* RTS is required to control the transmitter */
if (!sport->have_rtscts && !sport->have_rtsgpio)
rs485conf->flags &= ~SER_RS485_ENABLED;
if (rs485conf->flags & SER_RS485_ENABLED) {
/* disable transmitter */
temp = readl(sport->port.membase + UCR2);
if (rs485conf->flags & SER_RS485_RTS_AFTER_SEND)
imx_port_rts_active(sport, &temp);
else
imx_port_rts_inactive(sport, &temp);
writel(temp, sport->port.membase + UCR2);
}
/* Make sure Rx is enabled in case Tx is active with Rx disabled */
if (!(rs485conf->flags & SER_RS485_ENABLED) ||
rs485conf->flags & SER_RS485_RX_DURING_TX) {
temp = readl(sport->port.membase + UCR2);
temp |= UCR2_RXEN;
writel(temp, sport->port.membase + UCR2);
}
port->rs485 = *rs485conf;
return 0;
}
static const struct uart_ops imx_pops = {
.tx_empty = imx_tx_empty,
.set_mctrl = imx_set_mctrl,
.get_mctrl = imx_get_mctrl,
.stop_tx = imx_stop_tx,
.start_tx = imx_start_tx,
.stop_rx = imx_stop_rx,
.enable_ms = imx_enable_ms,
.break_ctl = imx_break_ctl,
.startup = imx_startup,
.shutdown = imx_shutdown,
.flush_buffer = imx_flush_buffer,
.set_termios = imx_set_termios,
.type = imx_type,
.config_port = imx_config_port,
.verify_port = imx_verify_port,
#if defined(CONFIG_CONSOLE_POLL)
.poll_init = imx_poll_init,
.poll_get_char = imx_poll_get_char,
.poll_put_char = imx_poll_put_char,
#endif
};
static struct imx_port *imx_ports[UART_NR];
#ifdef CONFIG_SERIAL_IMX_CONSOLE
static void imx_console_putchar(struct uart_port *port, int ch)
{
struct imx_port *sport = (struct imx_port *)port;
while (readl(sport->port.membase + uts_reg(sport)) & UTS_TXFULL)
barrier();
writel(ch, sport->port.membase + URTX0);
}
/*
* Interrupts are disabled on entering
*/
static void
imx_console_write(struct console *co, const char *s, unsigned int count)
{
struct imx_port *sport = imx_ports[co->index];
struct imx_port_ucrs old_ucr;
unsigned int ucr1;
unsigned long flags = 0;
serial: imx: Fix recursive locking bug commit 9ec1882df2 (tty: serial: imx: console write routing is unsafe on SMP) introduced a recursive locking bug in imx_console_write(). The callchain is: imx_rxint() spin_lock_irqsave(&sport->port.lock,flags); ... uart_handle_sysrq_char(); sysrq_function(); printk(); imx_console_write(); spin_lock_irqsave(&sport->port.lock,flags); <--- DEAD The bad news is that the kernel debugging facilities can dectect the problem, but the printks never surface on the serial console for obvious reasons. There is a similar issue with oops_in_progress. If the kernel crashes we really don't want to be stuck on the lock and unable to tell what happened. In general most UP originated drivers miss these checks and nobody ever notices because CONFIG_PROVE_LOCKING seems to be still ignored by a large number of developers. The solution is to avoid locking in the sysrq case and trylock in the oops_in_progress case. This scheme is used in other drivers as well and it would be nice if we could move this to a common place, so the usual copy/paste/modify bugs can be avoided. Now there is another issue with this scheme: CPU0 CPU1 printk() rxint() sysrq_detection() -> sets port->sysrq return from interrupt console_write() if (port->sysrq) avoid locking port->sysrq is reset with the next receive character. So as long as the port->sysrq is not reset and this can take an endless amount of time if after the break no futher receive character follows, all console writes happen unlocked. While the current writer is protected against other console writers by the console sem, it's unprotected against open/close or other operations which fiddle with the port. That's what the above mentioned commit tried to solve. That's an issue in all drivers which use that scheme and unfortunately there is no easy workaround. The only solution is to have a separate indicator port->sysrq_cpu. uart_handle_sysrq_char() then sets it to smp_processor_id() before calling into handle_sysrq() and resets it to -1 after that. Then change the locking check to: if (port->sysrq_cpu == smp_processor_id()) locked = 0; else if (oops_in_progress) locked = spin_trylock_irqsave(port->lock, flags); else spin_lock_irqsave(port->lock, flags); That would force all other cpus into the spin_lock path. Problem solved, but that's way beyond the scope of this fix and really wants to be implemented in a common function which calls the uart specific write function to avoid another gazillion of hard to debug copy/paste/modify bugs. Reported-and-tested-by: Tim Sander <tim@krieglstein.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable <stable@vger.kernel.org> # 3.6+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-02-15 03:01:06 +07:00
int locked = 1;
int retval;
Revert "serial: imx: remove unbalanced clk_prepare" This reverts commit 9e7b399d6528eac33a6fbfceb2b92af209c3454d. Commit ("9e7b399d6528ea") causes the following warning and sometimes also hangs the system: ------------[ cut here ]------------ WARNING: CPU: 0 PID: 0 at kernel/locking/mutex.c:868 mutex_trylock+0x20c/0x22c() DEBUG_LOCKS_WARN_ON(in_interrupt()) Modules linked in: CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.2.0-rc7-next-20150818-00001-g14418a6 #4 Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) Backtrace: [<80012f08>] (dump_backtrace) from [<800130a4>] (show_stack+0x18/0x1c) r6:00000364 r5:00000000 r4:00000000 r3:00000000 [<8001308c>] (show_stack) from [<807902b8>] (dump_stack+0x88/0xa4) [<80790230>] (dump_stack) from [<8002a604>] (warn_slowpath_common+0x80/0xbc) r5:807945c4 r4:80ab3b50 [<8002a584>] (warn_slowpath_common) from [<8002a6e4>] (warn_slowpath_fmt+0x38/0x40) r8:00000000 r7:8131100c r6:8054c3cc r5:8131300c r4:80b0a570 [<8002a6b0>] (warn_slowpath_fmt) from [<807945c4>] (mutex_trylock+0x20c/0x22c) r3:8095d0d8 r2:8095ab28 [<807943b8>] (mutex_trylock) from [<8054c3cc>] (clk_prepare_lock+0x14/0xf4) r7:8131100c r6:be3f0c80 r5:00000037 r4:be3f0c80 [<8054c3b8>] (clk_prepare_lock) from [<8054dbfc>] (clk_prepare+0x18/0x30) r5:00000037 r4:be3f0c80 [<8054dbe4>] (clk_prepare) from [<8036a600>] (imx_console_write+0x30/0x244) r4:812d0bc8 r3:8132b9a4 To reproduce the problem we only need to let the board idle for something like 30 seconds. Tested on a imx6q-sabresd. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Reviewed-by: Eduardo Valentin <edubezval@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-18 22:43:12 +07:00
retval = clk_enable(sport->clk_per);
if (retval)
return;
Revert "serial: imx: remove unbalanced clk_prepare" This reverts commit 9e7b399d6528eac33a6fbfceb2b92af209c3454d. Commit ("9e7b399d6528ea") causes the following warning and sometimes also hangs the system: ------------[ cut here ]------------ WARNING: CPU: 0 PID: 0 at kernel/locking/mutex.c:868 mutex_trylock+0x20c/0x22c() DEBUG_LOCKS_WARN_ON(in_interrupt()) Modules linked in: CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.2.0-rc7-next-20150818-00001-g14418a6 #4 Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) Backtrace: [<80012f08>] (dump_backtrace) from [<800130a4>] (show_stack+0x18/0x1c) r6:00000364 r5:00000000 r4:00000000 r3:00000000 [<8001308c>] (show_stack) from [<807902b8>] (dump_stack+0x88/0xa4) [<80790230>] (dump_stack) from [<8002a604>] (warn_slowpath_common+0x80/0xbc) r5:807945c4 r4:80ab3b50 [<8002a584>] (warn_slowpath_common) from [<8002a6e4>] (warn_slowpath_fmt+0x38/0x40) r8:00000000 r7:8131100c r6:8054c3cc r5:8131300c r4:80b0a570 [<8002a6b0>] (warn_slowpath_fmt) from [<807945c4>] (mutex_trylock+0x20c/0x22c) r3:8095d0d8 r2:8095ab28 [<807943b8>] (mutex_trylock) from [<8054c3cc>] (clk_prepare_lock+0x14/0xf4) r7:8131100c r6:be3f0c80 r5:00000037 r4:be3f0c80 [<8054c3b8>] (clk_prepare_lock) from [<8054dbfc>] (clk_prepare+0x18/0x30) r5:00000037 r4:be3f0c80 [<8054dbe4>] (clk_prepare) from [<8036a600>] (imx_console_write+0x30/0x244) r4:812d0bc8 r3:8132b9a4 To reproduce the problem we only need to let the board idle for something like 30 seconds. Tested on a imx6q-sabresd. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Reviewed-by: Eduardo Valentin <edubezval@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-18 22:43:12 +07:00
retval = clk_enable(sport->clk_ipg);
if (retval) {
Revert "serial: imx: remove unbalanced clk_prepare" This reverts commit 9e7b399d6528eac33a6fbfceb2b92af209c3454d. Commit ("9e7b399d6528ea") causes the following warning and sometimes also hangs the system: ------------[ cut here ]------------ WARNING: CPU: 0 PID: 0 at kernel/locking/mutex.c:868 mutex_trylock+0x20c/0x22c() DEBUG_LOCKS_WARN_ON(in_interrupt()) Modules linked in: CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.2.0-rc7-next-20150818-00001-g14418a6 #4 Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) Backtrace: [<80012f08>] (dump_backtrace) from [<800130a4>] (show_stack+0x18/0x1c) r6:00000364 r5:00000000 r4:00000000 r3:00000000 [<8001308c>] (show_stack) from [<807902b8>] (dump_stack+0x88/0xa4) [<80790230>] (dump_stack) from [<8002a604>] (warn_slowpath_common+0x80/0xbc) r5:807945c4 r4:80ab3b50 [<8002a584>] (warn_slowpath_common) from [<8002a6e4>] (warn_slowpath_fmt+0x38/0x40) r8:00000000 r7:8131100c r6:8054c3cc r5:8131300c r4:80b0a570 [<8002a6b0>] (warn_slowpath_fmt) from [<807945c4>] (mutex_trylock+0x20c/0x22c) r3:8095d0d8 r2:8095ab28 [<807943b8>] (mutex_trylock) from [<8054c3cc>] (clk_prepare_lock+0x14/0xf4) r7:8131100c r6:be3f0c80 r5:00000037 r4:be3f0c80 [<8054c3b8>] (clk_prepare_lock) from [<8054dbfc>] (clk_prepare+0x18/0x30) r5:00000037 r4:be3f0c80 [<8054dbe4>] (clk_prepare) from [<8036a600>] (imx_console_write+0x30/0x244) r4:812d0bc8 r3:8132b9a4 To reproduce the problem we only need to let the board idle for something like 30 seconds. Tested on a imx6q-sabresd. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Reviewed-by: Eduardo Valentin <edubezval@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-18 22:43:12 +07:00
clk_disable(sport->clk_per);
return;
}
serial: imx: Fix recursive locking bug commit 9ec1882df2 (tty: serial: imx: console write routing is unsafe on SMP) introduced a recursive locking bug in imx_console_write(). The callchain is: imx_rxint() spin_lock_irqsave(&sport->port.lock,flags); ... uart_handle_sysrq_char(); sysrq_function(); printk(); imx_console_write(); spin_lock_irqsave(&sport->port.lock,flags); <--- DEAD The bad news is that the kernel debugging facilities can dectect the problem, but the printks never surface on the serial console for obvious reasons. There is a similar issue with oops_in_progress. If the kernel crashes we really don't want to be stuck on the lock and unable to tell what happened. In general most UP originated drivers miss these checks and nobody ever notices because CONFIG_PROVE_LOCKING seems to be still ignored by a large number of developers. The solution is to avoid locking in the sysrq case and trylock in the oops_in_progress case. This scheme is used in other drivers as well and it would be nice if we could move this to a common place, so the usual copy/paste/modify bugs can be avoided. Now there is another issue with this scheme: CPU0 CPU1 printk() rxint() sysrq_detection() -> sets port->sysrq return from interrupt console_write() if (port->sysrq) avoid locking port->sysrq is reset with the next receive character. So as long as the port->sysrq is not reset and this can take an endless amount of time if after the break no futher receive character follows, all console writes happen unlocked. While the current writer is protected against other console writers by the console sem, it's unprotected against open/close or other operations which fiddle with the port. That's what the above mentioned commit tried to solve. That's an issue in all drivers which use that scheme and unfortunately there is no easy workaround. The only solution is to have a separate indicator port->sysrq_cpu. uart_handle_sysrq_char() then sets it to smp_processor_id() before calling into handle_sysrq() and resets it to -1 after that. Then change the locking check to: if (port->sysrq_cpu == smp_processor_id()) locked = 0; else if (oops_in_progress) locked = spin_trylock_irqsave(port->lock, flags); else spin_lock_irqsave(port->lock, flags); That would force all other cpus into the spin_lock path. Problem solved, but that's way beyond the scope of this fix and really wants to be implemented in a common function which calls the uart specific write function to avoid another gazillion of hard to debug copy/paste/modify bugs. Reported-and-tested-by: Tim Sander <tim@krieglstein.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable <stable@vger.kernel.org> # 3.6+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-02-15 03:01:06 +07:00
if (sport->port.sysrq)
locked = 0;
else if (oops_in_progress)
locked = spin_trylock_irqsave(&sport->port.lock, flags);
else
spin_lock_irqsave(&sport->port.lock, flags);
/*
* First, save UCR1/2/3 and then disable interrupts
*/
imx_port_ucrs_save(&sport->port, &old_ucr);
ucr1 = old_ucr.ucr1;
if (is_imx1_uart(sport))
ucr1 |= IMX1_UCR1_UARTCLKEN;
ucr1 |= UCR1_UARTEN;
ucr1 &= ~(UCR1_TXMPTYEN | UCR1_RRDYEN | UCR1_RTSDEN);
writel(ucr1, sport->port.membase + UCR1);
writel(old_ucr.ucr2 | UCR2_TXEN, sport->port.membase + UCR2);
uart_console_write(&sport->port, s, count, imx_console_putchar);
/*
* Finally, wait for transmitter to become empty
* and restore UCR1/2/3
*/
while (!(readl(sport->port.membase + USR2) & USR2_TXDC));
imx_port_ucrs_restore(&sport->port, &old_ucr);
serial: imx: Fix recursive locking bug commit 9ec1882df2 (tty: serial: imx: console write routing is unsafe on SMP) introduced a recursive locking bug in imx_console_write(). The callchain is: imx_rxint() spin_lock_irqsave(&sport->port.lock,flags); ... uart_handle_sysrq_char(); sysrq_function(); printk(); imx_console_write(); spin_lock_irqsave(&sport->port.lock,flags); <--- DEAD The bad news is that the kernel debugging facilities can dectect the problem, but the printks never surface on the serial console for obvious reasons. There is a similar issue with oops_in_progress. If the kernel crashes we really don't want to be stuck on the lock and unable to tell what happened. In general most UP originated drivers miss these checks and nobody ever notices because CONFIG_PROVE_LOCKING seems to be still ignored by a large number of developers. The solution is to avoid locking in the sysrq case and trylock in the oops_in_progress case. This scheme is used in other drivers as well and it would be nice if we could move this to a common place, so the usual copy/paste/modify bugs can be avoided. Now there is another issue with this scheme: CPU0 CPU1 printk() rxint() sysrq_detection() -> sets port->sysrq return from interrupt console_write() if (port->sysrq) avoid locking port->sysrq is reset with the next receive character. So as long as the port->sysrq is not reset and this can take an endless amount of time if after the break no futher receive character follows, all console writes happen unlocked. While the current writer is protected against other console writers by the console sem, it's unprotected against open/close or other operations which fiddle with the port. That's what the above mentioned commit tried to solve. That's an issue in all drivers which use that scheme and unfortunately there is no easy workaround. The only solution is to have a separate indicator port->sysrq_cpu. uart_handle_sysrq_char() then sets it to smp_processor_id() before calling into handle_sysrq() and resets it to -1 after that. Then change the locking check to: if (port->sysrq_cpu == smp_processor_id()) locked = 0; else if (oops_in_progress) locked = spin_trylock_irqsave(port->lock, flags); else spin_lock_irqsave(port->lock, flags); That would force all other cpus into the spin_lock path. Problem solved, but that's way beyond the scope of this fix and really wants to be implemented in a common function which calls the uart specific write function to avoid another gazillion of hard to debug copy/paste/modify bugs. Reported-and-tested-by: Tim Sander <tim@krieglstein.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable <stable@vger.kernel.org> # 3.6+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-02-15 03:01:06 +07:00
if (locked)
spin_unlock_irqrestore(&sport->port.lock, flags);
Revert "serial: imx: remove unbalanced clk_prepare" This reverts commit 9e7b399d6528eac33a6fbfceb2b92af209c3454d. Commit ("9e7b399d6528ea") causes the following warning and sometimes also hangs the system: ------------[ cut here ]------------ WARNING: CPU: 0 PID: 0 at kernel/locking/mutex.c:868 mutex_trylock+0x20c/0x22c() DEBUG_LOCKS_WARN_ON(in_interrupt()) Modules linked in: CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.2.0-rc7-next-20150818-00001-g14418a6 #4 Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) Backtrace: [<80012f08>] (dump_backtrace) from [<800130a4>] (show_stack+0x18/0x1c) r6:00000364 r5:00000000 r4:00000000 r3:00000000 [<8001308c>] (show_stack) from [<807902b8>] (dump_stack+0x88/0xa4) [<80790230>] (dump_stack) from [<8002a604>] (warn_slowpath_common+0x80/0xbc) r5:807945c4 r4:80ab3b50 [<8002a584>] (warn_slowpath_common) from [<8002a6e4>] (warn_slowpath_fmt+0x38/0x40) r8:00000000 r7:8131100c r6:8054c3cc r5:8131300c r4:80b0a570 [<8002a6b0>] (warn_slowpath_fmt) from [<807945c4>] (mutex_trylock+0x20c/0x22c) r3:8095d0d8 r2:8095ab28 [<807943b8>] (mutex_trylock) from [<8054c3cc>] (clk_prepare_lock+0x14/0xf4) r7:8131100c r6:be3f0c80 r5:00000037 r4:be3f0c80 [<8054c3b8>] (clk_prepare_lock) from [<8054dbfc>] (clk_prepare+0x18/0x30) r5:00000037 r4:be3f0c80 [<8054dbe4>] (clk_prepare) from [<8036a600>] (imx_console_write+0x30/0x244) r4:812d0bc8 r3:8132b9a4 To reproduce the problem we only need to let the board idle for something like 30 seconds. Tested on a imx6q-sabresd. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Reviewed-by: Eduardo Valentin <edubezval@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-18 22:43:12 +07:00
clk_disable(sport->clk_ipg);
clk_disable(sport->clk_per);
}
/*
* If the port was already initialised (eg, by a boot loader),
* try to determine the current setup.
*/
static void __init
imx_console_get_options(struct imx_port *sport, int *baud,
int *parity, int *bits)
{
if (readl(sport->port.membase + UCR1) & UCR1_UARTEN) {
/* ok, the port was enabled */
unsigned int ucr2, ubir, ubmr, uartclk;
unsigned int baud_raw;
unsigned int ucfr_rfdiv;
ucr2 = readl(sport->port.membase + UCR2);
*parity = 'n';
if (ucr2 & UCR2_PREN) {
if (ucr2 & UCR2_PROE)
*parity = 'o';
else
*parity = 'e';
}
if (ucr2 & UCR2_WS)
*bits = 8;
else
*bits = 7;
ubir = readl(sport->port.membase + UBIR) & 0xffff;
ubmr = readl(sport->port.membase + UBMR) & 0xffff;
ucfr_rfdiv = (readl(sport->port.membase + UFCR) & UFCR_RFDIV) >> 7;
if (ucfr_rfdiv == 6)
ucfr_rfdiv = 7;
else
ucfr_rfdiv = 6 - ucfr_rfdiv;
uartclk = clk_get_rate(sport->clk_per);
uartclk /= ucfr_rfdiv;
{ /*
* The next code provides exact computation of
* baud_raw = round(((uartclk/16) * (ubir + 1)) / (ubmr + 1))
* without need of float support or long long division,
* which would be required to prevent 32bit arithmetic overflow
*/
unsigned int mul = ubir + 1;
unsigned int div = 16 * (ubmr + 1);
unsigned int rem = uartclk % div;
baud_raw = (uartclk / div) * mul;
baud_raw += (rem * mul + div / 2) / div;
*baud = (baud_raw + 50) / 100 * 100;
}
if (*baud != baud_raw)
pr_info("Console IMX rounded baud rate from %d to %d\n",
baud_raw, *baud);
}
}
static int __init
imx_console_setup(struct console *co, char *options)
{
struct imx_port *sport;
int baud = 9600;
int bits = 8;
int parity = 'n';
int flow = 'n';
int retval;
/*
* Check whether an invalid uart number has been specified, and
* if so, search for the first available port that does have
* console support.
*/
if (co->index == -1 || co->index >= ARRAY_SIZE(imx_ports))
co->index = 0;
sport = imx_ports[co->index];
if (sport == NULL)
return -ENODEV;
/* For setting the registers, we only need to enable the ipg clock. */
retval = clk_prepare_enable(sport->clk_ipg);
if (retval)
goto error_console;
if (options)
uart_parse_options(options, &baud, &parity, &bits, &flow);
else
imx_console_get_options(sport, &baud, &parity, &bits);
imx_setup_ufcr(sport, TXTL_DEFAULT, RXTL_DEFAULT);
retval = uart_set_options(&sport->port, co, baud, parity, bits, flow);
Revert "serial: imx: remove unbalanced clk_prepare" This reverts commit 9e7b399d6528eac33a6fbfceb2b92af209c3454d. Commit ("9e7b399d6528ea") causes the following warning and sometimes also hangs the system: ------------[ cut here ]------------ WARNING: CPU: 0 PID: 0 at kernel/locking/mutex.c:868 mutex_trylock+0x20c/0x22c() DEBUG_LOCKS_WARN_ON(in_interrupt()) Modules linked in: CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.2.0-rc7-next-20150818-00001-g14418a6 #4 Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) Backtrace: [<80012f08>] (dump_backtrace) from [<800130a4>] (show_stack+0x18/0x1c) r6:00000364 r5:00000000 r4:00000000 r3:00000000 [<8001308c>] (show_stack) from [<807902b8>] (dump_stack+0x88/0xa4) [<80790230>] (dump_stack) from [<8002a604>] (warn_slowpath_common+0x80/0xbc) r5:807945c4 r4:80ab3b50 [<8002a584>] (warn_slowpath_common) from [<8002a6e4>] (warn_slowpath_fmt+0x38/0x40) r8:00000000 r7:8131100c r6:8054c3cc r5:8131300c r4:80b0a570 [<8002a6b0>] (warn_slowpath_fmt) from [<807945c4>] (mutex_trylock+0x20c/0x22c) r3:8095d0d8 r2:8095ab28 [<807943b8>] (mutex_trylock) from [<8054c3cc>] (clk_prepare_lock+0x14/0xf4) r7:8131100c r6:be3f0c80 r5:00000037 r4:be3f0c80 [<8054c3b8>] (clk_prepare_lock) from [<8054dbfc>] (clk_prepare+0x18/0x30) r5:00000037 r4:be3f0c80 [<8054dbe4>] (clk_prepare) from [<8036a600>] (imx_console_write+0x30/0x244) r4:812d0bc8 r3:8132b9a4 To reproduce the problem we only need to let the board idle for something like 30 seconds. Tested on a imx6q-sabresd. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Reviewed-by: Eduardo Valentin <edubezval@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-18 22:43:12 +07:00
clk_disable(sport->clk_ipg);
if (retval) {
clk_unprepare(sport->clk_ipg);
goto error_console;
}
retval = clk_prepare(sport->clk_per);
if (retval)
clk_disable_unprepare(sport->clk_ipg);
error_console:
return retval;
}
static struct uart_driver imx_reg;
static struct console imx_console = {
.name = DEV_NAME,
.write = imx_console_write,
.device = uart_console_device,
.setup = imx_console_setup,
.flags = CON_PRINTBUFFER,
.index = -1,
.data = &imx_reg,
};
#define IMX_CONSOLE &imx_console
#ifdef CONFIG_OF
static void imx_console_early_putchar(struct uart_port *port, int ch)
{
while (readl_relaxed(port->membase + IMX21_UTS) & UTS_TXFULL)
cpu_relax();
writel_relaxed(ch, port->membase + URTX0);
}
static void imx_console_early_write(struct console *con, const char *s,
unsigned count)
{
struct earlycon_device *dev = con->data;
uart_console_write(&dev->port, s, count, imx_console_early_putchar);
}
static int __init
imx_console_early_setup(struct earlycon_device *dev, const char *opt)
{
if (!dev->port.membase)
return -ENODEV;
dev->con->write = imx_console_early_write;
return 0;
}
OF_EARLYCON_DECLARE(ec_imx6q, "fsl,imx6q-uart", imx_console_early_setup);
OF_EARLYCON_DECLARE(ec_imx21, "fsl,imx21-uart", imx_console_early_setup);
#endif
#else
#define IMX_CONSOLE NULL
#endif
static struct uart_driver imx_reg = {
.owner = THIS_MODULE,
.driver_name = DRIVER_NAME,
.dev_name = DEV_NAME,
.major = SERIAL_IMX_MAJOR,
.minor = MINOR_START,
.nr = ARRAY_SIZE(imx_ports),
.cons = IMX_CONSOLE,
};
#ifdef CONFIG_OF
/*
* This function returns 1 iff pdev isn't a device instatiated by dt, 0 iff it
* could successfully get all information from dt or a negative errno.
*/
static int serial_imx_probe_dt(struct imx_port *sport,
struct platform_device *pdev)
{
struct device_node *np = pdev->dev.of_node;
int ret;
sport->devdata = of_device_get_match_data(&pdev->dev);
if (!sport->devdata)
/* no device tree device */
return 1;
ret = of_alias_get_id(np, "serial");
if (ret < 0) {
dev_err(&pdev->dev, "failed to get alias id, errno %d\n", ret);
return ret;
}
sport->port.line = ret;
if (of_get_property(np, "uart-has-rtscts", NULL) ||
of_get_property(np, "fsl,uart-has-rtscts", NULL) /* deprecated */)
sport->have_rtscts = 1;
if (of_get_property(np, "fsl,dte-mode", NULL))
sport->dte_mode = 1;
if (of_get_property(np, "rts-gpios", NULL))
sport->have_rtsgpio = 1;
return 0;
}
#else
static inline int serial_imx_probe_dt(struct imx_port *sport,
struct platform_device *pdev)
{
return 1;
}
#endif
static void serial_imx_probe_pdata(struct imx_port *sport,
struct platform_device *pdev)
{
struct imxuart_platform_data *pdata = dev_get_platdata(&pdev->dev);
sport->port.line = pdev->id;
sport->devdata = (struct imx_uart_data *) pdev->id_entry->driver_data;
if (!pdata)
return;
if (pdata->flags & IMXUART_HAVE_RTSCTS)
sport->have_rtscts = 1;
}
static int serial_imx_probe(struct platform_device *pdev)
{
struct imx_port *sport;
void __iomem *base;
int ret = 0, reg;
struct resource *res;
int txirq, rxirq, rtsirq;
sport = devm_kzalloc(&pdev->dev, sizeof(*sport), GFP_KERNEL);
if (!sport)
return -ENOMEM;
ret = serial_imx_probe_dt(sport, pdev);
if (ret > 0)
serial_imx_probe_pdata(sport, pdev);
else if (ret < 0)
return ret;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
base = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(base))
return PTR_ERR(base);
rxirq = platform_get_irq(pdev, 0);
txirq = platform_get_irq(pdev, 1);
rtsirq = platform_get_irq(pdev, 2);
sport->port.dev = &pdev->dev;
sport->port.mapbase = res->start;
sport->port.membase = base;
sport->port.type = PORT_IMX,
sport->port.iotype = UPIO_MEM;
sport->port.irq = rxirq;
sport->port.fifosize = 32;
sport->port.ops = &imx_pops;
sport->port.rs485_config = imx_rs485_config;
sport->port.rs485.flags =
SER_RS485_RTS_ON_SEND | SER_RS485_RX_DURING_TX;
sport->port.flags = UPF_BOOT_AUTOCONF;
init_timer(&sport->timer);
sport->timer.function = imx_timeout;
sport->timer.data = (unsigned long)sport;
sport->gpios = mctrl_gpio_init(&sport->port, 0);
if (IS_ERR(sport->gpios))
return PTR_ERR(sport->gpios);
sport->clk_ipg = devm_clk_get(&pdev->dev, "ipg");
if (IS_ERR(sport->clk_ipg)) {
ret = PTR_ERR(sport->clk_ipg);
dev_err(&pdev->dev, "failed to get ipg clk: %d\n", ret);
return ret;
}
sport->clk_per = devm_clk_get(&pdev->dev, "per");
if (IS_ERR(sport->clk_per)) {
ret = PTR_ERR(sport->clk_per);
dev_err(&pdev->dev, "failed to get per clk: %d\n", ret);
return ret;
}
sport->port.uartclk = clk_get_rate(sport->clk_per);
/* For register access, we only need to enable the ipg clock. */
ret = clk_prepare_enable(sport->clk_ipg);
if (ret) {
dev_err(&pdev->dev, "failed to enable per clk: %d\n", ret);
return ret;
}
/* Disable interrupts before requesting them */
reg = readl_relaxed(sport->port.membase + UCR1);
reg &= ~(UCR1_ADEN | UCR1_TRDYEN | UCR1_IDEN | UCR1_RRDYEN |
UCR1_TXMPTYEN | UCR1_RTSDEN);
writel_relaxed(reg, sport->port.membase + UCR1);
if (!is_imx1_uart(sport) && sport->dte_mode) {
/*
* The DCEDTE bit changes the direction of DSR, DCD, DTR and RI
* and influences if UCR3_RI and UCR3_DCD changes the level of RI
* and DCD (when they are outputs) or enables the respective
* irqs. So set this bit early, i.e. before requesting irqs.
*/
reg = readl(sport->port.membase + UFCR);
if (!(reg & UFCR_DCEDTE))
writel(reg | UFCR_DCEDTE, sport->port.membase + UFCR);
/*
* Disable UCR3_RI and UCR3_DCD irqs. They are also not
* enabled later because they cannot be cleared
* (confirmed on i.MX25) which makes them unusable.
*/
writel(IMX21_UCR3_RXDMUXSEL | UCR3_ADNIMP | UCR3_DSR,
sport->port.membase + UCR3);
} else {
unsigned long ucr3 = UCR3_DSR;
reg = readl(sport->port.membase + UFCR);
if (reg & UFCR_DCEDTE)
writel(reg & ~UFCR_DCEDTE, sport->port.membase + UFCR);
if (!is_imx1_uart(sport))
ucr3 |= IMX21_UCR3_RXDMUXSEL | UCR3_ADNIMP;
writel(ucr3, sport->port.membase + UCR3);
}
clk_disable_unprepare(sport->clk_ipg);
/*
* Allocate the IRQ(s) i.MX1 has three interrupts whereas later
* chips only have one interrupt.
*/
if (txirq > 0) {
ret = devm_request_irq(&pdev->dev, rxirq, imx_rxint, 0,
dev_name(&pdev->dev), sport);
if (ret) {
dev_err(&pdev->dev, "failed to request rx irq: %d\n",
ret);
return ret;
}
ret = devm_request_irq(&pdev->dev, txirq, imx_txint, 0,
dev_name(&pdev->dev), sport);
if (ret) {
dev_err(&pdev->dev, "failed to request tx irq: %d\n",
ret);
return ret;
}
} else {
ret = devm_request_irq(&pdev->dev, rxirq, imx_int, 0,
dev_name(&pdev->dev), sport);
if (ret) {
dev_err(&pdev->dev, "failed to request irq: %d\n", ret);
return ret;
}
}
imx_ports[sport->port.line] = sport;
platform_set_drvdata(pdev, sport);
return uart_add_one_port(&imx_reg, &sport->port);
}
static int serial_imx_remove(struct platform_device *pdev)
{
struct imx_port *sport = platform_get_drvdata(pdev);
return uart_remove_one_port(&imx_reg, &sport->port);
}
static void serial_imx_restore_context(struct imx_port *sport)
{
if (!sport->context_saved)
return;
writel(sport->saved_reg[4], sport->port.membase + UFCR);
writel(sport->saved_reg[5], sport->port.membase + UESC);
writel(sport->saved_reg[6], sport->port.membase + UTIM);
writel(sport->saved_reg[7], sport->port.membase + UBIR);
writel(sport->saved_reg[8], sport->port.membase + UBMR);
writel(sport->saved_reg[9], sport->port.membase + IMX21_UTS);
writel(sport->saved_reg[0], sport->port.membase + UCR1);
writel(sport->saved_reg[1] | UCR2_SRST, sport->port.membase + UCR2);
writel(sport->saved_reg[2], sport->port.membase + UCR3);
writel(sport->saved_reg[3], sport->port.membase + UCR4);
sport->context_saved = false;
}
static void serial_imx_save_context(struct imx_port *sport)
{
/* Save necessary regs */
sport->saved_reg[0] = readl(sport->port.membase + UCR1);
sport->saved_reg[1] = readl(sport->port.membase + UCR2);
sport->saved_reg[2] = readl(sport->port.membase + UCR3);
sport->saved_reg[3] = readl(sport->port.membase + UCR4);
sport->saved_reg[4] = readl(sport->port.membase + UFCR);
sport->saved_reg[5] = readl(sport->port.membase + UESC);
sport->saved_reg[6] = readl(sport->port.membase + UTIM);
sport->saved_reg[7] = readl(sport->port.membase + UBIR);
sport->saved_reg[8] = readl(sport->port.membase + UBMR);
sport->saved_reg[9] = readl(sport->port.membase + IMX21_UTS);
sport->context_saved = true;
}
static void serial_imx_enable_wakeup(struct imx_port *sport, bool on)
{
unsigned int val;
val = readl(sport->port.membase + UCR3);
if (on)
val |= UCR3_AWAKEN;
else
val &= ~UCR3_AWAKEN;
writel(val, sport->port.membase + UCR3);
val = readl(sport->port.membase + UCR1);
if (on)
val |= UCR1_RTSDEN;
else
val &= ~UCR1_RTSDEN;
writel(val, sport->port.membase + UCR1);
}
static int imx_serial_port_suspend_noirq(struct device *dev)
{
struct platform_device *pdev = to_platform_device(dev);
struct imx_port *sport = platform_get_drvdata(pdev);
int ret;
ret = clk_enable(sport->clk_ipg);
if (ret)
return ret;
serial_imx_save_context(sport);
clk_disable(sport->clk_ipg);
return 0;
}
static int imx_serial_port_resume_noirq(struct device *dev)
{
struct platform_device *pdev = to_platform_device(dev);
struct imx_port *sport = platform_get_drvdata(pdev);
int ret;
ret = clk_enable(sport->clk_ipg);
if (ret)
return ret;
serial_imx_restore_context(sport);
clk_disable(sport->clk_ipg);
return 0;
}
static int imx_serial_port_suspend(struct device *dev)
{
struct platform_device *pdev = to_platform_device(dev);
struct imx_port *sport = platform_get_drvdata(pdev);
/* enable wakeup from i.MX UART */
serial_imx_enable_wakeup(sport, true);
uart_suspend_port(&imx_reg, &sport->port);
serial: imx: Fix suspend / resume. When a non console i.MX UART is enabled in the device tree, system suspend fails due to an unprepared clock: [ 638.794563] PM: Syncing filesystems ... done. [ 638.878902] Freezing user space processes ... (elapsed 0.002 seconds) done. [ 638.888454] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 638.996697] PM: suspend of devices complete after 97.200 msecs [ 639.002611] PM: suspend devices took 0.100 seconds [ 639.013020] PM: late suspend of devices complete after 2.288 msecs [ 639.021486] ------------[ cut here ]------------ [ 639.026147] WARNING: CPU: 0 PID: 488 at drivers/clk/clk.c:732 clk_core_enable+0xc0/0x12c() [ 639.034413] Modules linked in: [ 639.037490] CPU: 0 PID: 488 Comm: system_server Tainted: G W 4.4.0-rc5-pknbsp-svn2214-atag-v4.4-rc5-121-gebfd9cb #1304 [ 639.049312] Hardware name: Freescale i.MX53 (Device Tree Support) [ 639.055444] [<c0016d54>] (unwind_backtrace) from [<c00140f8>] (show_stack+0x20/0x24) [ 639.063199] [<c00140f8>] (show_stack) from [<c02c99a0>] (dump_stack+0x20/0x28) [ 639.070442] [<c02c99a0>] (dump_stack) from [<c0024ca8>] (warn_slowpath_common+0x88/0xc0) [ 639.078541] [<c0024ca8>] (warn_slowpath_common) from [<c0024d0c>] (warn_slowpath_null+0x2c/0x34) [ 639.087332] [<c0024d0c>] (warn_slowpath_null) from [<c05171e8>] (clk_core_enable+0xc0/0x12c) [ 639.095777] [<c05171e8>] (clk_core_enable) from [<c05172f8>] (clk_enable+0x2c/0x40) [ 639.103441] [<c05172f8>] (clk_enable) from [<c0349880>] (imx_serial_port_suspend_noirq+0x20/0xe0) [ 639.112336] [<c0349880>] (imx_serial_port_suspend_noirq) from [<c03a26a0>] (dpm_run_callback+0x68/0x16c) [ 639.121825] [<c03a26a0>] (dpm_run_callback) from [<c03a2898>] (__device_suspend_noirq+0xf4/0x22c) [ 639.130705] [<c03a2898>] (__device_suspend_noirq) from [<c03a4b0c>] (dpm_suspend_noirq+0x148/0x30c) [ 639.139764] [<c03a4b0c>] (dpm_suspend_noirq) from [<c00511d4>] (suspend_devices_and_enter+0x2e8/0x6a4) [ 639.149078] [<c00511d4>] (suspend_devices_and_enter) from [<c00518a0>] (pm_suspend+0x310/0x4b8) [ 639.157782] [<c00518a0>] (pm_suspend) from [<c00500ec>] (state_store+0x7c/0xcc) [ 639.165099] [<c00500ec>] (state_store) from [<c02cb6dc>] (kobj_attr_store+0x1c/0x28) [ 639.172858] [<c02cb6dc>] (kobj_attr_store) from [<c01633d4>] (sysfs_kf_write+0x54/0x58) [ 639.180871] [<c01633d4>] (sysfs_kf_write) from [<c01629b4>] (kernfs_fop_write+0x100/0x1c8) [ 639.189152] [<c01629b4>] (kernfs_fop_write) from [<c00fb8b8>] (__vfs_write+0x3c/0xe8) [ 639.196991] [<c00fb8b8>] (__vfs_write) from [<c00fc810>] (vfs_write+0xa4/0x160) [ 639.204307] [<c00fc810>] (vfs_write) from [<c00fcac4>] (SyS_write+0x4c/0x98) [ 639.211363] [<c00fcac4>] (SyS_write) from [<c0010760>] (ret_fast_syscall+0x0/0x3c) This does not happen for the common case of a single UART used as a console (since imx_console_setup() already does a prepare) Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-01-05 22:53:31 +07:00
/* Needed to enable clock in suspend_noirq */
return clk_prepare(sport->clk_ipg);
}
static int imx_serial_port_resume(struct device *dev)
{
struct platform_device *pdev = to_platform_device(dev);
struct imx_port *sport = platform_get_drvdata(pdev);
/* disable wakeup from i.MX UART */
serial_imx_enable_wakeup(sport, false);
uart_resume_port(&imx_reg, &sport->port);
serial: imx: Fix suspend / resume. When a non console i.MX UART is enabled in the device tree, system suspend fails due to an unprepared clock: [ 638.794563] PM: Syncing filesystems ... done. [ 638.878902] Freezing user space processes ... (elapsed 0.002 seconds) done. [ 638.888454] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 638.996697] PM: suspend of devices complete after 97.200 msecs [ 639.002611] PM: suspend devices took 0.100 seconds [ 639.013020] PM: late suspend of devices complete after 2.288 msecs [ 639.021486] ------------[ cut here ]------------ [ 639.026147] WARNING: CPU: 0 PID: 488 at drivers/clk/clk.c:732 clk_core_enable+0xc0/0x12c() [ 639.034413] Modules linked in: [ 639.037490] CPU: 0 PID: 488 Comm: system_server Tainted: G W 4.4.0-rc5-pknbsp-svn2214-atag-v4.4-rc5-121-gebfd9cb #1304 [ 639.049312] Hardware name: Freescale i.MX53 (Device Tree Support) [ 639.055444] [<c0016d54>] (unwind_backtrace) from [<c00140f8>] (show_stack+0x20/0x24) [ 639.063199] [<c00140f8>] (show_stack) from [<c02c99a0>] (dump_stack+0x20/0x28) [ 639.070442] [<c02c99a0>] (dump_stack) from [<c0024ca8>] (warn_slowpath_common+0x88/0xc0) [ 639.078541] [<c0024ca8>] (warn_slowpath_common) from [<c0024d0c>] (warn_slowpath_null+0x2c/0x34) [ 639.087332] [<c0024d0c>] (warn_slowpath_null) from [<c05171e8>] (clk_core_enable+0xc0/0x12c) [ 639.095777] [<c05171e8>] (clk_core_enable) from [<c05172f8>] (clk_enable+0x2c/0x40) [ 639.103441] [<c05172f8>] (clk_enable) from [<c0349880>] (imx_serial_port_suspend_noirq+0x20/0xe0) [ 639.112336] [<c0349880>] (imx_serial_port_suspend_noirq) from [<c03a26a0>] (dpm_run_callback+0x68/0x16c) [ 639.121825] [<c03a26a0>] (dpm_run_callback) from [<c03a2898>] (__device_suspend_noirq+0xf4/0x22c) [ 639.130705] [<c03a2898>] (__device_suspend_noirq) from [<c03a4b0c>] (dpm_suspend_noirq+0x148/0x30c) [ 639.139764] [<c03a4b0c>] (dpm_suspend_noirq) from [<c00511d4>] (suspend_devices_and_enter+0x2e8/0x6a4) [ 639.149078] [<c00511d4>] (suspend_devices_and_enter) from [<c00518a0>] (pm_suspend+0x310/0x4b8) [ 639.157782] [<c00518a0>] (pm_suspend) from [<c00500ec>] (state_store+0x7c/0xcc) [ 639.165099] [<c00500ec>] (state_store) from [<c02cb6dc>] (kobj_attr_store+0x1c/0x28) [ 639.172858] [<c02cb6dc>] (kobj_attr_store) from [<c01633d4>] (sysfs_kf_write+0x54/0x58) [ 639.180871] [<c01633d4>] (sysfs_kf_write) from [<c01629b4>] (kernfs_fop_write+0x100/0x1c8) [ 639.189152] [<c01629b4>] (kernfs_fop_write) from [<c00fb8b8>] (__vfs_write+0x3c/0xe8) [ 639.196991] [<c00fb8b8>] (__vfs_write) from [<c00fc810>] (vfs_write+0xa4/0x160) [ 639.204307] [<c00fc810>] (vfs_write) from [<c00fcac4>] (SyS_write+0x4c/0x98) [ 639.211363] [<c00fcac4>] (SyS_write) from [<c0010760>] (ret_fast_syscall+0x0/0x3c) This does not happen for the common case of a single UART used as a console (since imx_console_setup() already does a prepare) Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-01-05 22:53:31 +07:00
clk_unprepare(sport->clk_ipg);
return 0;
}
static const struct dev_pm_ops imx_serial_port_pm_ops = {
.suspend_noirq = imx_serial_port_suspend_noirq,
.resume_noirq = imx_serial_port_resume_noirq,
.suspend = imx_serial_port_suspend,
.resume = imx_serial_port_resume,
};
static struct platform_driver serial_imx_driver = {
.probe = serial_imx_probe,
.remove = serial_imx_remove,
.id_table = imx_uart_devtype,
.driver = {
.name = "imx-uart",
.of_match_table = imx_uart_dt_ids,
.pm = &imx_serial_port_pm_ops,
},
};
static int __init imx_serial_init(void)
{
int ret = uart_register_driver(&imx_reg);
if (ret)
return ret;
ret = platform_driver_register(&serial_imx_driver);
if (ret != 0)
uart_unregister_driver(&imx_reg);
return ret;
}
static void __exit imx_serial_exit(void)
{
platform_driver_unregister(&serial_imx_driver);
uart_unregister_driver(&imx_reg);
}
module_init(imx_serial_init);
module_exit(imx_serial_exit);
MODULE_AUTHOR("Sascha Hauer");
MODULE_DESCRIPTION("IMX generic serial port driver");
MODULE_LICENSE("GPL");
MODULE_ALIAS("platform:imx-uart");