linux_dsm_epyc7002/include/linux/mmzone.h

1273 lines
40 KiB
C
Raw Normal View History

#ifndef _LINUX_MMZONE_H
#define _LINUX_MMZONE_H
#ifndef __ASSEMBLY__
#ifndef __GENERATING_BOUNDS_H
#include <linux/spinlock.h>
#include <linux/list.h>
#include <linux/wait.h>
#include <linux/bitops.h>
#include <linux/cache.h>
#include <linux/threads.h>
#include <linux/numa.h>
#include <linux/init.h>
#include <linux/seqlock.h>
#include <linux/nodemask.h>
Add a bitmap that is used to track flags affecting a block of pages Here is the latest revision of the anti-fragmentation patches. Of particular note in this version is special treatment of high-order atomic allocations. Care is taken to group them together and avoid grouping pages of other types near them. Artifical tests imply that it works. I'm trying to get the hardware together that would allow setting up of a "real" test. If anyone already has a setup and test that can trigger the atomic-allocation problem, I'd appreciate a test of these patches and a report. The second major change is that these patches will apply cleanly with patches that implement anti-fragmentation through zones. kernbench shows effectively no performance difference varying between -0.2% and +2% on a variety of test machines. Success rates for huge page allocation are dramatically increased. For example, on a ppc64 machine, the vanilla kernel was only able to allocate 1% of memory as a hugepage and this was due to a single hugepage reserved as min_free_kbytes. With these patches applied, 17% was allocatable as superpages. With reclaim-related fixes from Andy Whitcroft, it was 40% and further reclaim-related improvements should increase this further. Changelog Since V28 o Group high-order atomic allocations together o It is no longer required to set min_free_kbytes to 10% of memory. A value of 16384 in most cases will be sufficient o Now applied with zone-based anti-fragmentation o Fix incorrect VM_BUG_ON within buffered_rmqueue() o Reorder the stack so later patches do not back out work from earlier patches o Fix bug were journal pages were being treated as movable o Bias placement of non-movable pages to lower PFNs o More agressive clustering of reclaimable pages in reactions to workloads like updatedb that flood the size of inode caches Changelog Since V27 o Renamed anti-fragmentation to Page Clustering. Anti-fragmentation was giving the mistaken impression that it was the 100% solution for high order allocations. Instead, it greatly increases the chances high-order allocations will succeed and lays the foundation for defragmentation and memory hot-remove to work properly o Redefine page groupings based on ability to migrate or reclaim instead of basing on reclaimability alone o Get rid of spurious inits o Per-cpu lists are no longer split up per-type. Instead the per-cpu list is searched for a page of the appropriate type o Added more explanation commentary o Fix up bug in pageblock code where bitmap was used before being initalised Changelog Since V26 o Fix double init of lists in setup_pageset Changelog Since V25 o Fix loop order of for_each_rclmtype_order so that order of loop matches args o gfpflags_to_rclmtype uses gfp_t instead of unsigned long o Rename get_pageblock_type() to get_page_rclmtype() o Fix alignment problem in move_freepages() o Add mechanism for assigning flags to blocks of pages instead of page->flags o On fallback, do not examine the preferred list of free pages a second time The purpose of these patches is to reduce external fragmentation by grouping pages of related types together. When pages are migrated (or reclaimed under memory pressure), large contiguous pages will be freed. This patch works by categorising allocations by their ability to migrate; Movable - The pages may be moved with the page migration mechanism. These are generally userspace pages. Reclaimable - These are allocations for some kernel caches that are reclaimable or allocations that are known to be very short-lived. Unmovable - These are pages that are allocated by the kernel that are not trivially reclaimed. For example, the memory allocated for a loaded module would be in this category. By default, allocations are considered to be of this type HighAtomic - These are high-order allocations belonging to callers that cannot sleep or perform any IO. In practice, this is restricted to jumbo frame allocation for network receive. It is assumed that the allocations are short-lived Instead of having one MAX_ORDER-sized array of free lists in struct free_area, there is one for each type of reclaimability. Once a 2^MAX_ORDER block of pages is split for a type of allocation, it is added to the free-lists for that type, in effect reserving it. Hence, over time, pages of the different types can be clustered together. When the preferred freelists are expired, the largest possible block is taken from an alternative list. Buddies that are split from that large block are placed on the preferred allocation-type freelists to mitigate fragmentation. This implementation gives best-effort for low fragmentation in all zones. Ideally, min_free_kbytes needs to be set to a value equal to 4 * (1 << (MAX_ORDER-1)) pages in most cases. This would be 16384 on x86 and x86_64 for example. Our tests show that about 60-70% of physical memory can be allocated on a desktop after a few days uptime. In benchmarks and stress tests, we are finding that 80% of memory is available as contiguous blocks at the end of the test. To compare, a standard kernel was getting < 1% of memory as large pages on a desktop and about 8-12% of memory as large pages at the end of stress tests. Following this email are 12 patches that implement thie page grouping feature. The first patch introduces a mechanism for storing flags related to a whole block of pages. Then allocations are split between movable and all other allocations. Following that are patches to deal with per-cpu pages and make the mechanism configurable. The next patch moves free pages between lists when partially allocated blocks are used for pages of another migrate type. The second last patch groups reclaimable kernel allocations such as inode caches together. The final patch related to groupings keeps high-order atomic allocations. The last two patches are more concerned with control of fragmentation. The second last patch biases placement of non-movable allocations towards the start of memory. This is with a view of supporting memory hot-remove of DIMMs with higher PFNs in the future. The biasing could be enforced a lot heavier but it would cost. The last patch agressively clusters reclaimable pages like inode caches together. The fragmentation reduction strategy needs to track if pages within a block can be moved or reclaimed so that pages are freed to the appropriate list. This patch adds a bitmap for flags affecting a whole a MAX_ORDER block of pages. In non-SPARSEMEM configurations, the bitmap is stored in the struct zone and allocated during initialisation. SPARSEMEM statically allocates the bitmap in a struct mem_section so that bitmaps do not have to be resized during memory hotadd. This wastes a small amount of memory per unused section (usually sizeof(unsigned long)) but the complexity of dynamically allocating the memory is quite high. Additional credit to Andy Whitcroft who reviewed up an earlier implementation of the mechanism an suggested how to make it a *lot* cleaner. Signed-off-by: Mel Gorman <mel@csn.ul.ie> Cc: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16 15:25:47 +07:00
#include <linux/pageblock-flags.h>
#include <linux/page-flags-layout.h>
#include <linux/atomic.h>
[PATCH] Sparsemem build fix From: Ralf Baechle <ralf@linux-mips.org> <linux/mmzone.h> uses PAGE_SIZE, PAGE_SHIFT from <asm/page.h> without including that header itself. For some sparsemem configurations this may result in build errors like: CC init/initramfs.o In file included from include/linux/gfp.h:4, from include/linux/slab.h:15, from include/linux/percpu.h:4, from include/linux/rcupdate.h:41, from include/linux/dcache.h:10, from include/linux/fs.h:226, from init/initramfs.c:2: include/linux/mmzone.h:498:22: warning: "PAGE_SHIFT" is not defined In file included from include/linux/gfp.h:4, from include/linux/slab.h:15, from include/linux/percpu.h:4, from include/linux/rcupdate.h:41, from include/linux/dcache.h:10, from include/linux/fs.h:226, from init/initramfs.c:2: include/linux/mmzone.h:526: error: `PAGE_SIZE' undeclared here (not in a function) include/linux/mmzone.h: In function `__pfn_to_section': include/linux/mmzone.h:573: error: `PAGE_SHIFT' undeclared (first use in this function) include/linux/mmzone.h:573: error: (Each undeclared identifier is reported only once include/linux/mmzone.h:573: error: for each function it appears in.) include/linux/mmzone.h: In function `pfn_valid': include/linux/mmzone.h:578: error: `PAGE_SHIFT' undeclared (first use in this function) make[1]: *** [init/initramfs.o] Error 1 make: *** [init] Error 2 Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Seems-reasonable-to: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-04 16:51:29 +07:00
#include <asm/page.h>
/* Free memory management - zoned buddy allocator. */
#ifndef CONFIG_FORCE_MAX_ZONEORDER
#define MAX_ORDER 11
#else
#define MAX_ORDER CONFIG_FORCE_MAX_ZONEORDER
#endif
#define MAX_ORDER_NR_PAGES (1 << (MAX_ORDER - 1))
Lumpy Reclaim V4 When we are out of memory of a suitable size we enter reclaim. The current reclaim algorithm targets pages in LRU order, which is great for fairness at order-0 but highly unsuitable if you desire pages at higher orders. To get pages of higher order we must shoot down a very high proportion of memory; >95% in a lot of cases. This patch set adds a lumpy reclaim algorithm to the allocator. It targets groups of pages at the specified order anchored at the end of the active and inactive lists. This encourages groups of pages at the requested orders to move from active to inactive, and active to free lists. This behaviour is only triggered out of direct reclaim when higher order pages have been requested. This patch set is particularly effective when utilised with an anti-fragmentation scheme which groups pages of similar reclaimability together. This patch set is based on Peter Zijlstra's lumpy reclaim V2 patch which forms the foundation. Credit to Mel Gorman for sanitity checking. Mel said: The patches have an application with hugepage pool resizing. When lumpy-reclaim is used used with ZONE_MOVABLE, the hugepages pool can be resized with greater reliability. Testing on a desktop machine with 2GB of RAM showed that growing the hugepage pool with ZONE_MOVABLE on it's own was very slow as the success rate was quite low. Without lumpy-reclaim, each attempt to grow the pool by 100 pages would yield 1 or 2 hugepages. With lumpy-reclaim, getting 40 to 70 hugepages on each attempt was typical. [akpm@osdl.org: ia64 pfn_to_nid fixes and loop cleanup] [bunk@stusta.de: static declarations for internal functions] [a.p.zijlstra@chello.nl: initial lumpy V2 implementation] Signed-off-by: Andy Whitcroft <apw@shadowen.org> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Acked-by: Mel Gorman <mel@csn.ul.ie> Acked-by: Mel Gorman <mel@csn.ul.ie> Cc: Bob Picco <bob.picco@hp.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-17 18:03:16 +07:00
/*
* PAGE_ALLOC_COSTLY_ORDER is the order at which allocations are deemed
* costly to service. That is between allocation orders which should
* coalesce naturally under reasonable reclaim pressure and those which
Lumpy Reclaim V4 When we are out of memory of a suitable size we enter reclaim. The current reclaim algorithm targets pages in LRU order, which is great for fairness at order-0 but highly unsuitable if you desire pages at higher orders. To get pages of higher order we must shoot down a very high proportion of memory; >95% in a lot of cases. This patch set adds a lumpy reclaim algorithm to the allocator. It targets groups of pages at the specified order anchored at the end of the active and inactive lists. This encourages groups of pages at the requested orders to move from active to inactive, and active to free lists. This behaviour is only triggered out of direct reclaim when higher order pages have been requested. This patch set is particularly effective when utilised with an anti-fragmentation scheme which groups pages of similar reclaimability together. This patch set is based on Peter Zijlstra's lumpy reclaim V2 patch which forms the foundation. Credit to Mel Gorman for sanitity checking. Mel said: The patches have an application with hugepage pool resizing. When lumpy-reclaim is used used with ZONE_MOVABLE, the hugepages pool can be resized with greater reliability. Testing on a desktop machine with 2GB of RAM showed that growing the hugepage pool with ZONE_MOVABLE on it's own was very slow as the success rate was quite low. Without lumpy-reclaim, each attempt to grow the pool by 100 pages would yield 1 or 2 hugepages. With lumpy-reclaim, getting 40 to 70 hugepages on each attempt was typical. [akpm@osdl.org: ia64 pfn_to_nid fixes and loop cleanup] [bunk@stusta.de: static declarations for internal functions] [a.p.zijlstra@chello.nl: initial lumpy V2 implementation] Signed-off-by: Andy Whitcroft <apw@shadowen.org> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Acked-by: Mel Gorman <mel@csn.ul.ie> Acked-by: Mel Gorman <mel@csn.ul.ie> Cc: Bob Picco <bob.picco@hp.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-17 18:03:16 +07:00
* will not.
*/
#define PAGE_ALLOC_COSTLY_ORDER 3
enum {
MIGRATE_UNMOVABLE,
MIGRATE_RECLAIMABLE,
MIGRATE_MOVABLE,
MIGRATE_PCPTYPES, /* the number of types on the pcp lists */
MIGRATE_RESERVE = MIGRATE_PCPTYPES,
#ifdef CONFIG_CMA
/*
* MIGRATE_CMA migration type is designed to mimic the way
* ZONE_MOVABLE works. Only movable pages can be allocated
* from MIGRATE_CMA pageblocks and page allocator never
* implicitly change migration type of MIGRATE_CMA pageblock.
*
* The way to use it is to change migratetype of a range of
* pageblocks to MIGRATE_CMA which can be done by
* __free_pageblock_cma() function. What is important though
* is that a range of pageblocks must be aligned to
* MAX_ORDER_NR_PAGES should biggest page be bigger then
* a single pageblock.
*/
MIGRATE_CMA,
#endif
#ifdef CONFIG_MEMORY_ISOLATION
MIGRATE_ISOLATE, /* can't allocate from here */
#endif
MIGRATE_TYPES
};
#ifdef CONFIG_CMA
# define is_migrate_cma(migratetype) unlikely((migratetype) == MIGRATE_CMA)
#else
# define is_migrate_cma(migratetype) false
#endif
#define for_each_migratetype_order(order, type) \
for (order = 0; order < MAX_ORDER; order++) \
for (type = 0; type < MIGRATE_TYPES; type++)
Print out statistics in relation to fragmentation avoidance to /proc/pagetypeinfo This patch provides fragmentation avoidance statistics via /proc/pagetypeinfo. The information is collected only on request so there is no runtime overhead. The statistics are in three parts: The first part prints information on the size of blocks that pages are being grouped on and looks like Page block order: 10 Pages per block: 1024 The second part is a more detailed version of /proc/buddyinfo and looks like Free pages count per migrate type at order 0 1 2 3 4 5 6 7 8 9 10 Node 0, zone DMA, type Unmovable 0 0 0 0 0 0 0 0 0 0 0 Node 0, zone DMA, type Reclaimable 1 0 0 0 0 0 0 0 0 0 0 Node 0, zone DMA, type Movable 0 0 0 0 0 0 0 0 0 0 0 Node 0, zone DMA, type Reserve 0 4 4 0 0 0 0 1 0 1 0 Node 0, zone Normal, type Unmovable 111 8 4 4 2 3 1 0 0 0 0 Node 0, zone Normal, type Reclaimable 293 89 8 0 0 0 0 0 0 0 0 Node 0, zone Normal, type Movable 1 6 13 9 7 6 3 0 0 0 0 Node 0, zone Normal, type Reserve 0 0 0 0 0 0 0 0 0 0 4 The third part looks like Number of blocks type Unmovable Reclaimable Movable Reserve Node 0, zone DMA 0 1 2 1 Node 0, zone Normal 3 17 94 4 To walk the zones within a node with interrupts disabled, walk_zones_in_node() is introduced and shared between /proc/buddyinfo, /proc/zoneinfo and /proc/pagetypeinfo to reduce code duplication. It seems specific to what vmstat.c requires but could be broken out as a general utility function in mmzone.c if there were other other potential users. Signed-off-by: Mel Gorman <mel@csn.ul.ie> Acked-by: Andy Whitcroft <apw@shadowen.org> Acked-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16 15:26:02 +07:00
extern int page_group_by_mobility_disabled;
mm: page_alloc: use word-based accesses for get/set pageblock bitmaps The test_bit operations in get/set pageblock flags are expensive. This patch reads the bitmap on a word basis and use shifts and masks to isolate the bits of interest. Similarly masks are used to set a local copy of the bitmap and then use cmpxchg to update the bitmap if there have been no other changes made in parallel. In a test running dd onto tmpfs the overhead of the pageblock-related functions went from 1.27% in profiles to 0.5%. In addition to the performance benefits, this patch closes races that are possible between: a) get_ and set_pageblock_migratetype(), where get_pageblock_migratetype() reads part of the bits before and other part of the bits after set_pageblock_migratetype() has updated them. b) set_pageblock_migratetype() and set_pageblock_skip(), where the non-atomic read-modify-update set bit operation in set_pageblock_skip() will cause lost updates to some bits changed in the set_pageblock_migratetype(). Joonsoo Kim first reported the case a) via code inspection. Vlastimil Babka's testing with a debug patch showed that either a) or b) occurs roughly once per mmtests' stress-highalloc benchmark (although not necessarily in the same pageblock). Furthermore during development of unrelated compaction patches, it was observed that frequent calls to {start,undo}_isolate_page_range() the race occurs several thousands of times and has resulted in NULL pointer dereferences in move_freepages() and free_one_page() in places where free_list[migratetype] is manipulated by e.g. list_move(). Further debugging confirmed that migratetype had invalid value of 6, causing out of bounds access to the free_list array. That confirmed that the race exist, although it may be extremely rare, and currently only fatal where page isolation is performed due to memory hot remove. Races on pageblocks being updated by set_pageblock_migratetype(), where both old and new migratetype are lower MIGRATE_RESERVE, currently cannot result in an invalid value being observed, although theoretically they may still lead to unexpected creation or destruction of MIGRATE_RESERVE pageblocks. Furthermore, things could get suddenly worse when memory isolation is used more, or when new migratetypes are added. After this patch, the race has no longer been observed in testing. Signed-off-by: Mel Gorman <mgorman@suse.de> Acked-by: Vlastimil Babka <vbabka@suse.cz> Reported-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Reported-and-tested-by: Vlastimil Babka <vbabka@suse.cz> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Jan Kara <jack@suse.cz> Cc: Michal Hocko <mhocko@suse.cz> Cc: Hugh Dickins <hughd@google.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Theodore Ts'o <tytso@mit.edu> Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Rik van Riel <riel@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-06-05 06:10:16 +07:00
#define NR_MIGRATETYPE_BITS (PB_migrate_end - PB_migrate + 1)
#define MIGRATETYPE_MASK ((1UL << NR_MIGRATETYPE_BITS) - 1)
#define get_pageblock_migratetype(page) \
get_pfnblock_flags_mask(page, page_to_pfn(page), \
PB_migrate_end, MIGRATETYPE_MASK)
static inline int get_pfnblock_migratetype(struct page *page, unsigned long pfn)
Print out statistics in relation to fragmentation avoidance to /proc/pagetypeinfo This patch provides fragmentation avoidance statistics via /proc/pagetypeinfo. The information is collected only on request so there is no runtime overhead. The statistics are in three parts: The first part prints information on the size of blocks that pages are being grouped on and looks like Page block order: 10 Pages per block: 1024 The second part is a more detailed version of /proc/buddyinfo and looks like Free pages count per migrate type at order 0 1 2 3 4 5 6 7 8 9 10 Node 0, zone DMA, type Unmovable 0 0 0 0 0 0 0 0 0 0 0 Node 0, zone DMA, type Reclaimable 1 0 0 0 0 0 0 0 0 0 0 Node 0, zone DMA, type Movable 0 0 0 0 0 0 0 0 0 0 0 Node 0, zone DMA, type Reserve 0 4 4 0 0 0 0 1 0 1 0 Node 0, zone Normal, type Unmovable 111 8 4 4 2 3 1 0 0 0 0 Node 0, zone Normal, type Reclaimable 293 89 8 0 0 0 0 0 0 0 0 Node 0, zone Normal, type Movable 1 6 13 9 7 6 3 0 0 0 0 Node 0, zone Normal, type Reserve 0 0 0 0 0 0 0 0 0 0 4 The third part looks like Number of blocks type Unmovable Reclaimable Movable Reserve Node 0, zone DMA 0 1 2 1 Node 0, zone Normal 3 17 94 4 To walk the zones within a node with interrupts disabled, walk_zones_in_node() is introduced and shared between /proc/buddyinfo, /proc/zoneinfo and /proc/pagetypeinfo to reduce code duplication. It seems specific to what vmstat.c requires but could be broken out as a general utility function in mmzone.c if there were other other potential users. Signed-off-by: Mel Gorman <mel@csn.ul.ie> Acked-by: Andy Whitcroft <apw@shadowen.org> Acked-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16 15:26:02 +07:00
{
mm: page_alloc: use word-based accesses for get/set pageblock bitmaps The test_bit operations in get/set pageblock flags are expensive. This patch reads the bitmap on a word basis and use shifts and masks to isolate the bits of interest. Similarly masks are used to set a local copy of the bitmap and then use cmpxchg to update the bitmap if there have been no other changes made in parallel. In a test running dd onto tmpfs the overhead of the pageblock-related functions went from 1.27% in profiles to 0.5%. In addition to the performance benefits, this patch closes races that are possible between: a) get_ and set_pageblock_migratetype(), where get_pageblock_migratetype() reads part of the bits before and other part of the bits after set_pageblock_migratetype() has updated them. b) set_pageblock_migratetype() and set_pageblock_skip(), where the non-atomic read-modify-update set bit operation in set_pageblock_skip() will cause lost updates to some bits changed in the set_pageblock_migratetype(). Joonsoo Kim first reported the case a) via code inspection. Vlastimil Babka's testing with a debug patch showed that either a) or b) occurs roughly once per mmtests' stress-highalloc benchmark (although not necessarily in the same pageblock). Furthermore during development of unrelated compaction patches, it was observed that frequent calls to {start,undo}_isolate_page_range() the race occurs several thousands of times and has resulted in NULL pointer dereferences in move_freepages() and free_one_page() in places where free_list[migratetype] is manipulated by e.g. list_move(). Further debugging confirmed that migratetype had invalid value of 6, causing out of bounds access to the free_list array. That confirmed that the race exist, although it may be extremely rare, and currently only fatal where page isolation is performed due to memory hot remove. Races on pageblocks being updated by set_pageblock_migratetype(), where both old and new migratetype are lower MIGRATE_RESERVE, currently cannot result in an invalid value being observed, although theoretically they may still lead to unexpected creation or destruction of MIGRATE_RESERVE pageblocks. Furthermore, things could get suddenly worse when memory isolation is used more, or when new migratetypes are added. After this patch, the race has no longer been observed in testing. Signed-off-by: Mel Gorman <mgorman@suse.de> Acked-by: Vlastimil Babka <vbabka@suse.cz> Reported-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Reported-and-tested-by: Vlastimil Babka <vbabka@suse.cz> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Jan Kara <jack@suse.cz> Cc: Michal Hocko <mhocko@suse.cz> Cc: Hugh Dickins <hughd@google.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Theodore Ts'o <tytso@mit.edu> Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Rik van Riel <riel@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-06-05 06:10:16 +07:00
BUILD_BUG_ON(PB_migrate_end - PB_migrate != 2);
return get_pfnblock_flags_mask(page, pfn, PB_migrate_end,
MIGRATETYPE_MASK);
Print out statistics in relation to fragmentation avoidance to /proc/pagetypeinfo This patch provides fragmentation avoidance statistics via /proc/pagetypeinfo. The information is collected only on request so there is no runtime overhead. The statistics are in three parts: The first part prints information on the size of blocks that pages are being grouped on and looks like Page block order: 10 Pages per block: 1024 The second part is a more detailed version of /proc/buddyinfo and looks like Free pages count per migrate type at order 0 1 2 3 4 5 6 7 8 9 10 Node 0, zone DMA, type Unmovable 0 0 0 0 0 0 0 0 0 0 0 Node 0, zone DMA, type Reclaimable 1 0 0 0 0 0 0 0 0 0 0 Node 0, zone DMA, type Movable 0 0 0 0 0 0 0 0 0 0 0 Node 0, zone DMA, type Reserve 0 4 4 0 0 0 0 1 0 1 0 Node 0, zone Normal, type Unmovable 111 8 4 4 2 3 1 0 0 0 0 Node 0, zone Normal, type Reclaimable 293 89 8 0 0 0 0 0 0 0 0 Node 0, zone Normal, type Movable 1 6 13 9 7 6 3 0 0 0 0 Node 0, zone Normal, type Reserve 0 0 0 0 0 0 0 0 0 0 4 The third part looks like Number of blocks type Unmovable Reclaimable Movable Reserve Node 0, zone DMA 0 1 2 1 Node 0, zone Normal 3 17 94 4 To walk the zones within a node with interrupts disabled, walk_zones_in_node() is introduced and shared between /proc/buddyinfo, /proc/zoneinfo and /proc/pagetypeinfo to reduce code duplication. It seems specific to what vmstat.c requires but could be broken out as a general utility function in mmzone.c if there were other other potential users. Signed-off-by: Mel Gorman <mel@csn.ul.ie> Acked-by: Andy Whitcroft <apw@shadowen.org> Acked-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16 15:26:02 +07:00
}
struct free_area {
struct list_head free_list[MIGRATE_TYPES];
unsigned long nr_free;
};
struct pglist_data;
/*
* zone->lock and zone->lru_lock are two of the hottest locks in the kernel.
* So add a wild amount of padding here to ensure that they fall into separate
* cachelines. There are very few zone structures in the machine, so space
* consumption is not a concern here.
*/
#if defined(CONFIG_SMP)
struct zone_padding {
char x[0];
} ____cacheline_internodealigned_in_smp;
#define ZONE_PADDING(name) struct zone_padding name;
#else
#define ZONE_PADDING(name)
#endif
[PATCH] zoned vm counters: basic ZVC (zoned vm counter) implementation Per zone counter infrastructure The counters that we currently have for the VM are split per processor. The processor however has not much to do with the zone these pages belong to. We cannot tell f.e. how many ZONE_DMA pages are dirty. So we are blind to potentially inbalances in the usage of memory in various zones. F.e. in a NUMA system we cannot tell how many pages are dirty on a particular node. If we knew then we could put measures into the VM to balance the use of memory between different zones and different nodes in a NUMA system. For example it would be possible to limit the dirty pages per node so that fast local memory is kept available even if a process is dirtying huge amounts of pages. Another example is zone reclaim. We do not know how many unmapped pages exist per zone. So we just have to try to reclaim. If it is not working then we pause and try again later. It would be better if we knew when it makes sense to reclaim unmapped pages from a zone. This patchset allows the determination of the number of unmapped pages per zone. We can remove the zone reclaim interval with the counters introduced here. Futhermore the ability to have various usage statistics available will allow the development of new NUMA balancing algorithms that may be able to improve the decision making in the scheduler of when to move a process to another node and hopefully will also enable automatic page migration through a user space program that can analyse the memory load distribution and then rebalance memory use in order to increase performance. The counter framework here implements differential counters for each processor in struct zone. The differential counters are consolidated when a threshold is exceeded (like done in the current implementation for nr_pageache), when slab reaping occurs or when a consolidation function is called. Consolidation uses atomic operations and accumulates counters per zone in the zone structure and also globally in the vm_stat array. VM functions can access the counts by simply indexing a global or zone specific array. The arrangement of counters in an array also simplifies processing when output has to be generated for /proc/*. Counters can be updated by calling inc/dec_zone_page_state or _inc/dec_zone_page_state analogous to *_page_state. The second group of functions can be called if it is known that interrupts are disabled. Special optimized increment and decrement functions are provided. These can avoid certain checks and use increment or decrement instructions that an architecture may provide. We also add a new CONFIG_DMA_IS_NORMAL that signifies that an architecture can do DMA to all memory and therefore ZONE_NORMAL will not be populated. This is only currently set for IA64 SGI SN2 and currently only affects node_page_state(). In the best case node_page_state can be reduced to retrieving a single counter for the one zone on the node. [akpm@osdl.org: cleanups] [akpm@osdl.org: export vm_stat[] for filesystems] Signed-off-by: Christoph Lameter <clameter@sgi.com> Cc: Trond Myklebust <trond.myklebust@fys.uio.no> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-30 15:55:33 +07:00
enum zone_stat_item {
/* First 128 byte cacheline (assuming 64 bit words) */
NR_FREE_PAGES,
mm: page_alloc: fair zone allocator policy Each zone that holds userspace pages of one workload must be aged at a speed proportional to the zone size. Otherwise, the time an individual page gets to stay in memory depends on the zone it happened to be allocated in. Asymmetry in the zone aging creates rather unpredictable aging behavior and results in the wrong pages being reclaimed, activated etc. But exactly this happens right now because of the way the page allocator and kswapd interact. The page allocator uses per-node lists of all zones in the system, ordered by preference, when allocating a new page. When the first iteration does not yield any results, kswapd is woken up and the allocator retries. Due to the way kswapd reclaims zones below the high watermark while a zone can be allocated from when it is above the low watermark, the allocator may keep kswapd running while kswapd reclaim ensures that the page allocator can keep allocating from the first zone in the zonelist for extended periods of time. Meanwhile the other zones rarely see new allocations and thus get aged much slower in comparison. The result is that the occasional page placed in lower zones gets relatively more time in memory, even gets promoted to the active list after its peers have long been evicted. Meanwhile, the bulk of the working set may be thrashing on the preferred zone even though there may be significant amounts of memory available in the lower zones. Even the most basic test -- repeatedly reading a file slightly bigger than memory -- shows how broken the zone aging is. In this scenario, no single page should be able stay in memory long enough to get referenced twice and activated, but activation happens in spades: $ grep active_file /proc/zoneinfo nr_inactive_file 0 nr_active_file 0 nr_inactive_file 0 nr_active_file 8 nr_inactive_file 1582 nr_active_file 11994 $ cat data data data data >/dev/null $ grep active_file /proc/zoneinfo nr_inactive_file 0 nr_active_file 70 nr_inactive_file 258753 nr_active_file 443214 nr_inactive_file 149793 nr_active_file 12021 Fix this with a very simple round robin allocator. Each zone is allowed a batch of allocations that is proportional to the zone's size, after which it is treated as full. The batch counters are reset when all zones have been tried and the allocator enters the slowpath and kicks off kswapd reclaim. Allocation and reclaim is now fairly spread out to all available/allowable zones: $ grep active_file /proc/zoneinfo nr_inactive_file 0 nr_active_file 0 nr_inactive_file 174 nr_active_file 4865 nr_inactive_file 53 nr_active_file 860 $ cat data data data data >/dev/null $ grep active_file /proc/zoneinfo nr_inactive_file 0 nr_active_file 0 nr_inactive_file 666622 nr_active_file 4988 nr_inactive_file 190969 nr_active_file 937 When zone_reclaim_mode is enabled, allocations will now spread out to all zones on the local node, not just the first preferred zone (which on a 4G node might be a tiny Normal zone). Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Mel Gorman <mgorman@suse.de> Reviewed-by: Rik van Riel <riel@redhat.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Paul Bolle <paul.bollee@gmail.com> Cc: Zlatko Calusic <zcalusic@bitsync.net> Tested-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-09-12 04:20:47 +07:00
NR_ALLOC_BATCH,
NR_LRU_BASE,
vmscan: split LRU lists into anon & file sets Split the LRU lists in two, one set for pages that are backed by real file systems ("file") and one for pages that are backed by memory and swap ("anon"). The latter includes tmpfs. The advantage of doing this is that the VM will not have to scan over lots of anonymous pages (which we generally do not want to swap out), just to find the page cache pages that it should evict. This patch has the infrastructure and a basic policy to balance how much we scan the anon lists and how much we scan the file lists. The big policy changes are in separate patches. [lee.schermerhorn@hp.com: collect lru meminfo statistics from correct offset] [kosaki.motohiro@jp.fujitsu.com: prevent incorrect oom under split_lru] [kosaki.motohiro@jp.fujitsu.com: fix pagevec_move_tail() doesn't treat unevictable page] [hugh@veritas.com: memcg swapbacked pages active] [hugh@veritas.com: splitlru: BDI_CAP_SWAP_BACKED] [akpm@linux-foundation.org: fix /proc/vmstat units] [nishimura@mxp.nes.nec.co.jp: memcg: fix handling of shmem migration] [kosaki.motohiro@jp.fujitsu.com: adjust Quicklists field of /proc/meminfo] [kosaki.motohiro@jp.fujitsu.com: fix style issue of get_scan_ratio()] Signed-off-by: Rik van Riel <riel@redhat.com> Signed-off-by: Lee Schermerhorn <Lee.Schermerhorn@hp.com> Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by: Hugh Dickins <hugh@veritas.com> Signed-off-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 10:26:32 +07:00
NR_INACTIVE_ANON = NR_LRU_BASE, /* must match order of LRU_[IN]ACTIVE */
NR_ACTIVE_ANON, /* " " " " " */
NR_INACTIVE_FILE, /* " " " " " */
NR_ACTIVE_FILE, /* " " " " " */
Unevictable LRU Infrastructure When the system contains lots of mlocked or otherwise unevictable pages, the pageout code (kswapd) can spend lots of time scanning over these pages. Worse still, the presence of lots of unevictable pages can confuse kswapd into thinking that more aggressive pageout modes are required, resulting in all kinds of bad behaviour. Infrastructure to manage pages excluded from reclaim--i.e., hidden from vmscan. Based on a patch by Larry Woodman of Red Hat. Reworked to maintain "unevictable" pages on a separate per-zone LRU list, to "hide" them from vmscan. Kosaki Motohiro added the support for the memory controller unevictable lru list. Pages on the unevictable list have both PG_unevictable and PG_lru set. Thus, PG_unevictable is analogous to and mutually exclusive with PG_active--it specifies which LRU list the page is on. The unevictable infrastructure is enabled by a new mm Kconfig option [CONFIG_]UNEVICTABLE_LRU. A new function 'page_evictable(page, vma)' in vmscan.c tests whether or not a page may be evictable. Subsequent patches will add the various !evictable tests. We'll want to keep these tests light-weight for use in shrink_active_list() and, possibly, the fault path. To avoid races between tasks putting pages [back] onto an LRU list and tasks that might be moving the page from non-evictable to evictable state, the new function 'putback_lru_page()' -- inverse to 'isolate_lru_page()' -- tests the "evictability" of a page after placing it on the LRU, before dropping the reference. If the page has become unevictable, putback_lru_page() will redo the 'putback', thus moving the page to the unevictable list. This way, we avoid "stranding" evictable pages on the unevictable list. [akpm@linux-foundation.org: fix fallout from out-of-order merge] [riel@redhat.com: fix UNEVICTABLE_LRU and !PROC_PAGE_MONITOR build] [nishimura@mxp.nes.nec.co.jp: remove redundant mapping check] [kosaki.motohiro@jp.fujitsu.com: unevictable-lru-infrastructure: putback_lru_page()/unevictable page handling rework] [kosaki.motohiro@jp.fujitsu.com: kill unnecessary lock_page() in vmscan.c] [kosaki.motohiro@jp.fujitsu.com: revert migration change of unevictable lru infrastructure] [kosaki.motohiro@jp.fujitsu.com: revert to unevictable-lru-infrastructure-kconfig-fix.patch] [kosaki.motohiro@jp.fujitsu.com: restore patch failure of vmstat-unevictable-and-mlocked-pages-vm-events.patch] Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com> Signed-off-by: Rik van Riel <riel@redhat.com> Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Debugged-by: Benjamin Kidwell <benjkidwell@yahoo.com> Signed-off-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp> Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 10:26:39 +07:00
NR_UNEVICTABLE, /* " " " " " */
NR_MLOCK, /* mlock()ed pages found and moved off LRU */
NR_ANON_PAGES, /* Mapped anonymous pages */
NR_FILE_MAPPED, /* pagecache pages mapped into pagetables.
only modified from process context */
NR_FILE_PAGES,
NR_FILE_DIRTY,
NR_WRITEBACK,
NR_SLAB_RECLAIMABLE,
NR_SLAB_UNRECLAIMABLE,
NR_PAGETABLE, /* used for pagetables */
NR_KERNEL_STACK,
/* Second 128 byte cacheline */
NR_UNSTABLE_NFS, /* NFS unstable pages */
NR_BOUNCE,
NR_VMSCAN_WRITE,
NR_VMSCAN_IMMEDIATE, /* Prioritise for reclaim when writeback ends */
NR_WRITEBACK_TEMP, /* Writeback using temporary buffers */
NR_ISOLATED_ANON, /* Temporary isolated pages from anon lru */
NR_ISOLATED_FILE, /* Temporary isolated pages from file lru */
NR_SHMEM, /* shmem pages (included tmpfs/GEM pages) */
NR_DIRTIED, /* page dirtyings since bootup */
NR_WRITTEN, /* page writings since bootup */
NR_PAGES_SCANNED, /* pages scanned since last reclaim */
#ifdef CONFIG_NUMA
NUMA_HIT, /* allocated in intended node */
NUMA_MISS, /* allocated in non intended node */
NUMA_FOREIGN, /* was intended here, hit elsewhere */
NUMA_INTERLEAVE_HIT, /* interleaver preferred this zone */
NUMA_LOCAL, /* allocation from local node */
NUMA_OTHER, /* allocation from other node */
#endif
mm: thrash detection-based file cache sizing The VM maintains cached filesystem pages on two types of lists. One list holds the pages recently faulted into the cache, the other list holds pages that have been referenced repeatedly on that first list. The idea is to prefer reclaiming young pages over those that have shown to benefit from caching in the past. We call the recently usedbut ultimately was not significantly better than a FIFO policy and still thrashed cache based on eviction speed, rather than actual demand for cache. This patch solves one half of the problem by decoupling the ability to detect working set changes from the inactive list size. By maintaining a history of recently evicted file pages it can detect frequently used pages with an arbitrarily small inactive list size, and subsequently apply pressure on the active list based on actual demand for cache, not just overall eviction speed. Every zone maintains a counter that tracks inactive list aging speed. When a page is evicted, a snapshot of this counter is stored in the now-empty page cache radix tree slot. On refault, the minimum access distance of the page can be assessed, to evaluate whether the page should be part of the active list or not. This fixes the VM's blindness towards working set changes in excess of the inactive list. And it's the foundation to further improve the protection ability and reduce the minimum inactive list size of 50%. Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Reviewed-by: Rik van Riel <riel@redhat.com> Reviewed-by: Minchan Kim <minchan@kernel.org> Reviewed-by: Bob Liu <bob.liu@oracle.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Dave Chinner <david@fromorbit.com> Cc: Greg Thelen <gthelen@google.com> Cc: Hugh Dickins <hughd@google.com> Cc: Jan Kara <jack@suse.cz> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Luigi Semenzato <semenzato@google.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Metin Doslu <metin@citusdata.com> Cc: Michel Lespinasse <walken@google.com> Cc: Ozgun Erdogan <ozgun@citusdata.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Roman Gushchin <klamm@yandex-team.ru> Cc: Ryan Mallon <rmallon@gmail.com> Cc: Tejun Heo <tj@kernel.org> Cc: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-04-04 04:47:51 +07:00
WORKINGSET_REFAULT,
WORKINGSET_ACTIVATE,
mm: keep page cache radix tree nodes in check Previously, page cache radix tree nodes were freed after reclaim emptied out their page pointers. But now reclaim stores shadow entries in their place, which are only reclaimed when the inodes themselves are reclaimed. This is problematic for bigger files that are still in use after they have a significant amount of their cache reclaimed, without any of those pages actually refaulting. The shadow entries will just sit there and waste memory. In the worst case, the shadow entries will accumulate until the machine runs out of memory. To get this under control, the VM will track radix tree nodes exclusively containing shadow entries on a per-NUMA node list. Per-NUMA rather than global because we expect the radix tree nodes themselves to be allocated node-locally and we want to reduce cross-node references of otherwise independent cache workloads. A simple shrinker will then reclaim these nodes on memory pressure. A few things need to be stored in the radix tree node to implement the shadow node LRU and allow tree deletions coming from the list: 1. There is no index available that would describe the reverse path from the node up to the tree root, which is needed to perform a deletion. To solve this, encode in each node its offset inside the parent. This can be stored in the unused upper bits of the same member that stores the node's height at no extra space cost. 2. The number of shadow entries needs to be counted in addition to the regular entries, to quickly detect when the node is ready to go to the shadow node LRU list. The current entry count is an unsigned int but the maximum number of entries is 64, so a shadow counter can easily be stored in the unused upper bits. 3. Tree modification needs tree lock and tree root, which are located in the address space, so store an address_space backpointer in the node. The parent pointer of the node is in a union with the 2-word rcu_head, so the backpointer comes at no extra cost as well. 4. The node needs to be linked to an LRU list, which requires a list head inside the node. This does increase the size of the node, but it does not change the number of objects that fit into a slab page. [akpm@linux-foundation.org: export the right function] Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Reviewed-by: Rik van Riel <riel@redhat.com> Reviewed-by: Minchan Kim <minchan@kernel.org> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Bob Liu <bob.liu@oracle.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Dave Chinner <david@fromorbit.com> Cc: Greg Thelen <gthelen@google.com> Cc: Hugh Dickins <hughd@google.com> Cc: Jan Kara <jack@suse.cz> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Luigi Semenzato <semenzato@google.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Metin Doslu <metin@citusdata.com> Cc: Michel Lespinasse <walken@google.com> Cc: Ozgun Erdogan <ozgun@citusdata.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Roman Gushchin <klamm@yandex-team.ru> Cc: Ryan Mallon <rmallon@gmail.com> Cc: Tejun Heo <tj@kernel.org> Cc: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-04-04 04:47:56 +07:00
WORKINGSET_NODERECLAIM,
NR_ANON_TRANSPARENT_HUGEPAGES,
NR_FREE_CMA_PAGES,
[PATCH] zoned vm counters: basic ZVC (zoned vm counter) implementation Per zone counter infrastructure The counters that we currently have for the VM are split per processor. The processor however has not much to do with the zone these pages belong to. We cannot tell f.e. how many ZONE_DMA pages are dirty. So we are blind to potentially inbalances in the usage of memory in various zones. F.e. in a NUMA system we cannot tell how many pages are dirty on a particular node. If we knew then we could put measures into the VM to balance the use of memory between different zones and different nodes in a NUMA system. For example it would be possible to limit the dirty pages per node so that fast local memory is kept available even if a process is dirtying huge amounts of pages. Another example is zone reclaim. We do not know how many unmapped pages exist per zone. So we just have to try to reclaim. If it is not working then we pause and try again later. It would be better if we knew when it makes sense to reclaim unmapped pages from a zone. This patchset allows the determination of the number of unmapped pages per zone. We can remove the zone reclaim interval with the counters introduced here. Futhermore the ability to have various usage statistics available will allow the development of new NUMA balancing algorithms that may be able to improve the decision making in the scheduler of when to move a process to another node and hopefully will also enable automatic page migration through a user space program that can analyse the memory load distribution and then rebalance memory use in order to increase performance. The counter framework here implements differential counters for each processor in struct zone. The differential counters are consolidated when a threshold is exceeded (like done in the current implementation for nr_pageache), when slab reaping occurs or when a consolidation function is called. Consolidation uses atomic operations and accumulates counters per zone in the zone structure and also globally in the vm_stat array. VM functions can access the counts by simply indexing a global or zone specific array. The arrangement of counters in an array also simplifies processing when output has to be generated for /proc/*. Counters can be updated by calling inc/dec_zone_page_state or _inc/dec_zone_page_state analogous to *_page_state. The second group of functions can be called if it is known that interrupts are disabled. Special optimized increment and decrement functions are provided. These can avoid certain checks and use increment or decrement instructions that an architecture may provide. We also add a new CONFIG_DMA_IS_NORMAL that signifies that an architecture can do DMA to all memory and therefore ZONE_NORMAL will not be populated. This is only currently set for IA64 SGI SN2 and currently only affects node_page_state(). In the best case node_page_state can be reduced to retrieving a single counter for the one zone on the node. [akpm@osdl.org: cleanups] [akpm@osdl.org: export vm_stat[] for filesystems] Signed-off-by: Christoph Lameter <clameter@sgi.com> Cc: Trond Myklebust <trond.myklebust@fys.uio.no> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-30 15:55:33 +07:00
NR_VM_ZONE_STAT_ITEMS };
vmscan: split LRU lists into anon & file sets Split the LRU lists in two, one set for pages that are backed by real file systems ("file") and one for pages that are backed by memory and swap ("anon"). The latter includes tmpfs. The advantage of doing this is that the VM will not have to scan over lots of anonymous pages (which we generally do not want to swap out), just to find the page cache pages that it should evict. This patch has the infrastructure and a basic policy to balance how much we scan the anon lists and how much we scan the file lists. The big policy changes are in separate patches. [lee.schermerhorn@hp.com: collect lru meminfo statistics from correct offset] [kosaki.motohiro@jp.fujitsu.com: prevent incorrect oom under split_lru] [kosaki.motohiro@jp.fujitsu.com: fix pagevec_move_tail() doesn't treat unevictable page] [hugh@veritas.com: memcg swapbacked pages active] [hugh@veritas.com: splitlru: BDI_CAP_SWAP_BACKED] [akpm@linux-foundation.org: fix /proc/vmstat units] [nishimura@mxp.nes.nec.co.jp: memcg: fix handling of shmem migration] [kosaki.motohiro@jp.fujitsu.com: adjust Quicklists field of /proc/meminfo] [kosaki.motohiro@jp.fujitsu.com: fix style issue of get_scan_ratio()] Signed-off-by: Rik van Riel <riel@redhat.com> Signed-off-by: Lee Schermerhorn <Lee.Schermerhorn@hp.com> Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by: Hugh Dickins <hugh@veritas.com> Signed-off-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 10:26:32 +07:00
/*
* We do arithmetic on the LRU lists in various places in the code,
* so it is important to keep the active lists LRU_ACTIVE higher in
* the array than the corresponding inactive lists, and to keep
* the *_FILE lists LRU_FILE higher than the corresponding _ANON lists.
*
* This has to be kept in sync with the statistics in zone_stat_item
* above and the descriptions in vmstat_text in mm/vmstat.c
*/
#define LRU_BASE 0
#define LRU_ACTIVE 1
#define LRU_FILE 2
enum lru_list {
vmscan: split LRU lists into anon & file sets Split the LRU lists in two, one set for pages that are backed by real file systems ("file") and one for pages that are backed by memory and swap ("anon"). The latter includes tmpfs. The advantage of doing this is that the VM will not have to scan over lots of anonymous pages (which we generally do not want to swap out), just to find the page cache pages that it should evict. This patch has the infrastructure and a basic policy to balance how much we scan the anon lists and how much we scan the file lists. The big policy changes are in separate patches. [lee.schermerhorn@hp.com: collect lru meminfo statistics from correct offset] [kosaki.motohiro@jp.fujitsu.com: prevent incorrect oom under split_lru] [kosaki.motohiro@jp.fujitsu.com: fix pagevec_move_tail() doesn't treat unevictable page] [hugh@veritas.com: memcg swapbacked pages active] [hugh@veritas.com: splitlru: BDI_CAP_SWAP_BACKED] [akpm@linux-foundation.org: fix /proc/vmstat units] [nishimura@mxp.nes.nec.co.jp: memcg: fix handling of shmem migration] [kosaki.motohiro@jp.fujitsu.com: adjust Quicklists field of /proc/meminfo] [kosaki.motohiro@jp.fujitsu.com: fix style issue of get_scan_ratio()] Signed-off-by: Rik van Riel <riel@redhat.com> Signed-off-by: Lee Schermerhorn <Lee.Schermerhorn@hp.com> Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by: Hugh Dickins <hugh@veritas.com> Signed-off-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 10:26:32 +07:00
LRU_INACTIVE_ANON = LRU_BASE,
LRU_ACTIVE_ANON = LRU_BASE + LRU_ACTIVE,
LRU_INACTIVE_FILE = LRU_BASE + LRU_FILE,
LRU_ACTIVE_FILE = LRU_BASE + LRU_FILE + LRU_ACTIVE,
Unevictable LRU Infrastructure When the system contains lots of mlocked or otherwise unevictable pages, the pageout code (kswapd) can spend lots of time scanning over these pages. Worse still, the presence of lots of unevictable pages can confuse kswapd into thinking that more aggressive pageout modes are required, resulting in all kinds of bad behaviour. Infrastructure to manage pages excluded from reclaim--i.e., hidden from vmscan. Based on a patch by Larry Woodman of Red Hat. Reworked to maintain "unevictable" pages on a separate per-zone LRU list, to "hide" them from vmscan. Kosaki Motohiro added the support for the memory controller unevictable lru list. Pages on the unevictable list have both PG_unevictable and PG_lru set. Thus, PG_unevictable is analogous to and mutually exclusive with PG_active--it specifies which LRU list the page is on. The unevictable infrastructure is enabled by a new mm Kconfig option [CONFIG_]UNEVICTABLE_LRU. A new function 'page_evictable(page, vma)' in vmscan.c tests whether or not a page may be evictable. Subsequent patches will add the various !evictable tests. We'll want to keep these tests light-weight for use in shrink_active_list() and, possibly, the fault path. To avoid races between tasks putting pages [back] onto an LRU list and tasks that might be moving the page from non-evictable to evictable state, the new function 'putback_lru_page()' -- inverse to 'isolate_lru_page()' -- tests the "evictability" of a page after placing it on the LRU, before dropping the reference. If the page has become unevictable, putback_lru_page() will redo the 'putback', thus moving the page to the unevictable list. This way, we avoid "stranding" evictable pages on the unevictable list. [akpm@linux-foundation.org: fix fallout from out-of-order merge] [riel@redhat.com: fix UNEVICTABLE_LRU and !PROC_PAGE_MONITOR build] [nishimura@mxp.nes.nec.co.jp: remove redundant mapping check] [kosaki.motohiro@jp.fujitsu.com: unevictable-lru-infrastructure: putback_lru_page()/unevictable page handling rework] [kosaki.motohiro@jp.fujitsu.com: kill unnecessary lock_page() in vmscan.c] [kosaki.motohiro@jp.fujitsu.com: revert migration change of unevictable lru infrastructure] [kosaki.motohiro@jp.fujitsu.com: revert to unevictable-lru-infrastructure-kconfig-fix.patch] [kosaki.motohiro@jp.fujitsu.com: restore patch failure of vmstat-unevictable-and-mlocked-pages-vm-events.patch] Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com> Signed-off-by: Rik van Riel <riel@redhat.com> Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Debugged-by: Benjamin Kidwell <benjkidwell@yahoo.com> Signed-off-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp> Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 10:26:39 +07:00
LRU_UNEVICTABLE,
NR_LRU_LISTS
};
#define for_each_lru(lru) for (lru = 0; lru < NR_LRU_LISTS; lru++)
#define for_each_evictable_lru(lru) for (lru = 0; lru <= LRU_ACTIVE_FILE; lru++)
Unevictable LRU Infrastructure When the system contains lots of mlocked or otherwise unevictable pages, the pageout code (kswapd) can spend lots of time scanning over these pages. Worse still, the presence of lots of unevictable pages can confuse kswapd into thinking that more aggressive pageout modes are required, resulting in all kinds of bad behaviour. Infrastructure to manage pages excluded from reclaim--i.e., hidden from vmscan. Based on a patch by Larry Woodman of Red Hat. Reworked to maintain "unevictable" pages on a separate per-zone LRU list, to "hide" them from vmscan. Kosaki Motohiro added the support for the memory controller unevictable lru list. Pages on the unevictable list have both PG_unevictable and PG_lru set. Thus, PG_unevictable is analogous to and mutually exclusive with PG_active--it specifies which LRU list the page is on. The unevictable infrastructure is enabled by a new mm Kconfig option [CONFIG_]UNEVICTABLE_LRU. A new function 'page_evictable(page, vma)' in vmscan.c tests whether or not a page may be evictable. Subsequent patches will add the various !evictable tests. We'll want to keep these tests light-weight for use in shrink_active_list() and, possibly, the fault path. To avoid races between tasks putting pages [back] onto an LRU list and tasks that might be moving the page from non-evictable to evictable state, the new function 'putback_lru_page()' -- inverse to 'isolate_lru_page()' -- tests the "evictability" of a page after placing it on the LRU, before dropping the reference. If the page has become unevictable, putback_lru_page() will redo the 'putback', thus moving the page to the unevictable list. This way, we avoid "stranding" evictable pages on the unevictable list. [akpm@linux-foundation.org: fix fallout from out-of-order merge] [riel@redhat.com: fix UNEVICTABLE_LRU and !PROC_PAGE_MONITOR build] [nishimura@mxp.nes.nec.co.jp: remove redundant mapping check] [kosaki.motohiro@jp.fujitsu.com: unevictable-lru-infrastructure: putback_lru_page()/unevictable page handling rework] [kosaki.motohiro@jp.fujitsu.com: kill unnecessary lock_page() in vmscan.c] [kosaki.motohiro@jp.fujitsu.com: revert migration change of unevictable lru infrastructure] [kosaki.motohiro@jp.fujitsu.com: revert to unevictable-lru-infrastructure-kconfig-fix.patch] [kosaki.motohiro@jp.fujitsu.com: restore patch failure of vmstat-unevictable-and-mlocked-pages-vm-events.patch] Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com> Signed-off-by: Rik van Riel <riel@redhat.com> Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Debugged-by: Benjamin Kidwell <benjkidwell@yahoo.com> Signed-off-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp> Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 10:26:39 +07:00
static inline int is_file_lru(enum lru_list lru)
vmscan: split LRU lists into anon & file sets Split the LRU lists in two, one set for pages that are backed by real file systems ("file") and one for pages that are backed by memory and swap ("anon"). The latter includes tmpfs. The advantage of doing this is that the VM will not have to scan over lots of anonymous pages (which we generally do not want to swap out), just to find the page cache pages that it should evict. This patch has the infrastructure and a basic policy to balance how much we scan the anon lists and how much we scan the file lists. The big policy changes are in separate patches. [lee.schermerhorn@hp.com: collect lru meminfo statistics from correct offset] [kosaki.motohiro@jp.fujitsu.com: prevent incorrect oom under split_lru] [kosaki.motohiro@jp.fujitsu.com: fix pagevec_move_tail() doesn't treat unevictable page] [hugh@veritas.com: memcg swapbacked pages active] [hugh@veritas.com: splitlru: BDI_CAP_SWAP_BACKED] [akpm@linux-foundation.org: fix /proc/vmstat units] [nishimura@mxp.nes.nec.co.jp: memcg: fix handling of shmem migration] [kosaki.motohiro@jp.fujitsu.com: adjust Quicklists field of /proc/meminfo] [kosaki.motohiro@jp.fujitsu.com: fix style issue of get_scan_ratio()] Signed-off-by: Rik van Riel <riel@redhat.com> Signed-off-by: Lee Schermerhorn <Lee.Schermerhorn@hp.com> Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by: Hugh Dickins <hugh@veritas.com> Signed-off-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 10:26:32 +07:00
{
return (lru == LRU_INACTIVE_FILE || lru == LRU_ACTIVE_FILE);
vmscan: split LRU lists into anon & file sets Split the LRU lists in two, one set for pages that are backed by real file systems ("file") and one for pages that are backed by memory and swap ("anon"). The latter includes tmpfs. The advantage of doing this is that the VM will not have to scan over lots of anonymous pages (which we generally do not want to swap out), just to find the page cache pages that it should evict. This patch has the infrastructure and a basic policy to balance how much we scan the anon lists and how much we scan the file lists. The big policy changes are in separate patches. [lee.schermerhorn@hp.com: collect lru meminfo statistics from correct offset] [kosaki.motohiro@jp.fujitsu.com: prevent incorrect oom under split_lru] [kosaki.motohiro@jp.fujitsu.com: fix pagevec_move_tail() doesn't treat unevictable page] [hugh@veritas.com: memcg swapbacked pages active] [hugh@veritas.com: splitlru: BDI_CAP_SWAP_BACKED] [akpm@linux-foundation.org: fix /proc/vmstat units] [nishimura@mxp.nes.nec.co.jp: memcg: fix handling of shmem migration] [kosaki.motohiro@jp.fujitsu.com: adjust Quicklists field of /proc/meminfo] [kosaki.motohiro@jp.fujitsu.com: fix style issue of get_scan_ratio()] Signed-off-by: Rik van Riel <riel@redhat.com> Signed-off-by: Lee Schermerhorn <Lee.Schermerhorn@hp.com> Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by: Hugh Dickins <hugh@veritas.com> Signed-off-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 10:26:32 +07:00
}
static inline int is_active_lru(enum lru_list lru)
{
return (lru == LRU_ACTIVE_ANON || lru == LRU_ACTIVE_FILE);
}
static inline int is_unevictable_lru(enum lru_list lru)
Unevictable LRU Infrastructure When the system contains lots of mlocked or otherwise unevictable pages, the pageout code (kswapd) can spend lots of time scanning over these pages. Worse still, the presence of lots of unevictable pages can confuse kswapd into thinking that more aggressive pageout modes are required, resulting in all kinds of bad behaviour. Infrastructure to manage pages excluded from reclaim--i.e., hidden from vmscan. Based on a patch by Larry Woodman of Red Hat. Reworked to maintain "unevictable" pages on a separate per-zone LRU list, to "hide" them from vmscan. Kosaki Motohiro added the support for the memory controller unevictable lru list. Pages on the unevictable list have both PG_unevictable and PG_lru set. Thus, PG_unevictable is analogous to and mutually exclusive with PG_active--it specifies which LRU list the page is on. The unevictable infrastructure is enabled by a new mm Kconfig option [CONFIG_]UNEVICTABLE_LRU. A new function 'page_evictable(page, vma)' in vmscan.c tests whether or not a page may be evictable. Subsequent patches will add the various !evictable tests. We'll want to keep these tests light-weight for use in shrink_active_list() and, possibly, the fault path. To avoid races between tasks putting pages [back] onto an LRU list and tasks that might be moving the page from non-evictable to evictable state, the new function 'putback_lru_page()' -- inverse to 'isolate_lru_page()' -- tests the "evictability" of a page after placing it on the LRU, before dropping the reference. If the page has become unevictable, putback_lru_page() will redo the 'putback', thus moving the page to the unevictable list. This way, we avoid "stranding" evictable pages on the unevictable list. [akpm@linux-foundation.org: fix fallout from out-of-order merge] [riel@redhat.com: fix UNEVICTABLE_LRU and !PROC_PAGE_MONITOR build] [nishimura@mxp.nes.nec.co.jp: remove redundant mapping check] [kosaki.motohiro@jp.fujitsu.com: unevictable-lru-infrastructure: putback_lru_page()/unevictable page handling rework] [kosaki.motohiro@jp.fujitsu.com: kill unnecessary lock_page() in vmscan.c] [kosaki.motohiro@jp.fujitsu.com: revert migration change of unevictable lru infrastructure] [kosaki.motohiro@jp.fujitsu.com: revert to unevictable-lru-infrastructure-kconfig-fix.patch] [kosaki.motohiro@jp.fujitsu.com: restore patch failure of vmstat-unevictable-and-mlocked-pages-vm-events.patch] Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com> Signed-off-by: Rik van Riel <riel@redhat.com> Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Debugged-by: Benjamin Kidwell <benjkidwell@yahoo.com> Signed-off-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp> Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 10:26:39 +07:00
{
return (lru == LRU_UNEVICTABLE);
Unevictable LRU Infrastructure When the system contains lots of mlocked or otherwise unevictable pages, the pageout code (kswapd) can spend lots of time scanning over these pages. Worse still, the presence of lots of unevictable pages can confuse kswapd into thinking that more aggressive pageout modes are required, resulting in all kinds of bad behaviour. Infrastructure to manage pages excluded from reclaim--i.e., hidden from vmscan. Based on a patch by Larry Woodman of Red Hat. Reworked to maintain "unevictable" pages on a separate per-zone LRU list, to "hide" them from vmscan. Kosaki Motohiro added the support for the memory controller unevictable lru list. Pages on the unevictable list have both PG_unevictable and PG_lru set. Thus, PG_unevictable is analogous to and mutually exclusive with PG_active--it specifies which LRU list the page is on. The unevictable infrastructure is enabled by a new mm Kconfig option [CONFIG_]UNEVICTABLE_LRU. A new function 'page_evictable(page, vma)' in vmscan.c tests whether or not a page may be evictable. Subsequent patches will add the various !evictable tests. We'll want to keep these tests light-weight for use in shrink_active_list() and, possibly, the fault path. To avoid races between tasks putting pages [back] onto an LRU list and tasks that might be moving the page from non-evictable to evictable state, the new function 'putback_lru_page()' -- inverse to 'isolate_lru_page()' -- tests the "evictability" of a page after placing it on the LRU, before dropping the reference. If the page has become unevictable, putback_lru_page() will redo the 'putback', thus moving the page to the unevictable list. This way, we avoid "stranding" evictable pages on the unevictable list. [akpm@linux-foundation.org: fix fallout from out-of-order merge] [riel@redhat.com: fix UNEVICTABLE_LRU and !PROC_PAGE_MONITOR build] [nishimura@mxp.nes.nec.co.jp: remove redundant mapping check] [kosaki.motohiro@jp.fujitsu.com: unevictable-lru-infrastructure: putback_lru_page()/unevictable page handling rework] [kosaki.motohiro@jp.fujitsu.com: kill unnecessary lock_page() in vmscan.c] [kosaki.motohiro@jp.fujitsu.com: revert migration change of unevictable lru infrastructure] [kosaki.motohiro@jp.fujitsu.com: revert to unevictable-lru-infrastructure-kconfig-fix.patch] [kosaki.motohiro@jp.fujitsu.com: restore patch failure of vmstat-unevictable-and-mlocked-pages-vm-events.patch] Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com> Signed-off-by: Rik van Riel <riel@redhat.com> Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Debugged-by: Benjamin Kidwell <benjkidwell@yahoo.com> Signed-off-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp> Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-19 10:26:39 +07:00
}
struct zone_reclaim_stat {
/*
* The pageout code in vmscan.c keeps track of how many of the
* mem/swap backed and file backed pages are referenced.
* The higher the rotated/scanned ratio, the more valuable
* that cache is.
*
* The anon LRU stats live in [0], file LRU stats in [1]
*/
unsigned long recent_rotated[2];
unsigned long recent_scanned[2];
};
struct lruvec {
struct list_head lists[NR_LRU_LISTS];
struct zone_reclaim_stat reclaim_stat;
#ifdef CONFIG_MEMCG
struct zone *zone;
#endif
};
memcg: consolidate memory cgroup lru stat functions In mm/memcontrol.c, there are many lru stat functions as.. mem_cgroup_zone_nr_lru_pages mem_cgroup_node_nr_file_lru_pages mem_cgroup_nr_file_lru_pages mem_cgroup_node_nr_anon_lru_pages mem_cgroup_nr_anon_lru_pages mem_cgroup_node_nr_unevictable_lru_pages mem_cgroup_nr_unevictable_lru_pages mem_cgroup_node_nr_lru_pages mem_cgroup_nr_lru_pages mem_cgroup_get_local_zonestat Some of them are under #ifdef MAX_NUMNODES >1 and others are not. This seems bad. This patch consolidates all functions into mem_cgroup_zone_nr_lru_pages() mem_cgroup_node_nr_lru_pages() mem_cgroup_nr_lru_pages() For these functions, "which LRU?" information is passed by a mask. example: mem_cgroup_nr_lru_pages(mem, BIT(LRU_ACTIVE_ANON)) And I added some macro as ALL_LRU, ALL_LRU_FILE, ALL_LRU_ANON. example: mem_cgroup_nr_lru_pages(mem, ALL_LRU) BTW, considering layout of NUMA memory placement of counters, this patch seems to be better. Now, when we gather all LRU information, we scan in following orer for_each_lru -> for_each_node -> for_each_zone. This means we'll touch cache lines in different node in turn. After patch, we'll scan for_each_node -> for_each_zone -> for_each_lru(mask) Then, we'll gather information in the same cacheline at once. [akpm@linux-foundation.org: fix warnigns, build error] Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp> Cc: Balbir Singh <bsingharora@gmail.com> Cc: Michal Hocko <mhocko@suse.cz> Cc: Ying Han <yinghan@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-07-27 06:08:22 +07:00
/* Mask used at gathering information at once (see memcontrol.c) */
#define LRU_ALL_FILE (BIT(LRU_INACTIVE_FILE) | BIT(LRU_ACTIVE_FILE))
#define LRU_ALL_ANON (BIT(LRU_INACTIVE_ANON) | BIT(LRU_ACTIVE_ANON))
#define LRU_ALL ((1 << NR_LRU_LISTS) - 1)
/* Isolate clean file */
#define ISOLATE_CLEAN ((__force isolate_mode_t)0x1)
/* Isolate unmapped file */
#define ISOLATE_UNMAPPED ((__force isolate_mode_t)0x2)
/* Isolate for asynchronous migration */
#define ISOLATE_ASYNC_MIGRATE ((__force isolate_mode_t)0x4)
/* Isolate unevictable pages */
#define ISOLATE_UNEVICTABLE ((__force isolate_mode_t)0x8)
/* LRU Isolation modes. */
typedef unsigned __bitwise__ isolate_mode_t;
enum zone_watermarks {
WMARK_MIN,
WMARK_LOW,
WMARK_HIGH,
NR_WMARK
};
#define min_wmark_pages(z) (z->watermark[WMARK_MIN])
#define low_wmark_pages(z) (z->watermark[WMARK_LOW])
#define high_wmark_pages(z) (z->watermark[WMARK_HIGH])
struct per_cpu_pages {
int count; /* number of pages in the list */
int high; /* high watermark, emptying needed */
int batch; /* chunk size for buddy add/remove */
page-allocator: split per-cpu list into one-list-per-migrate-type The following two patches remove searching in the page allocator fast-path by maintaining multiple free-lists in the per-cpu structure. At the time the search was introduced, increasing the per-cpu structures would waste a lot of memory as per-cpu structures were statically allocated at compile-time. This is no longer the case. The patches are as follows. They are based on mmotm-2009-08-27. Patch 1 adds multiple lists to struct per_cpu_pages, one per migratetype that can be stored on the PCP lists. Patch 2 notes that the pcpu drain path check empty lists multiple times. The patch reduces the number of checks by maintaining a count of free lists encountered. Lists containing pages will then free multiple pages in batch The patches were tested with kernbench, netperf udp/tcp, hackbench and sysbench. The netperf tests were not bound to any CPU in particular and were run such that the results should be 99% confidence that the reported results are within 1% of the estimated mean. sysbench was run with a postgres background and read-only tests. Similar to netperf, it was run multiple times so that it's 99% confidence results are within 1%. The patches were tested on x86, x86-64 and ppc64 as x86: Intel Pentium D 3GHz with 8G RAM (no-brand machine) kernbench - No significant difference, variance well within noise netperf-udp - 1.34% to 2.28% gain netperf-tcp - 0.45% to 1.22% gain hackbench - Small variances, very close to noise sysbench - Very small gains x86-64: AMD Phenom 9950 1.3GHz with 8G RAM (no-brand machine) kernbench - No significant difference, variance well within noise netperf-udp - 1.83% to 10.42% gains netperf-tcp - No conclusive until buffer >= PAGE_SIZE 4096 +15.83% 8192 + 0.34% (not significant) 16384 + 1% hackbench - Small gains, very close to noise sysbench - 0.79% to 1.6% gain ppc64: PPC970MP 2.5GHz with 10GB RAM (it's a terrasoft powerstation) kernbench - No significant difference, variance well within noise netperf-udp - 2-3% gain for almost all buffer sizes tested netperf-tcp - losses on small buffers, gains on larger buffers possibly indicates some bad caching effect. hackbench - No significant difference sysbench - 2-4% gain This patch: Currently the per-cpu page allocator searches the PCP list for pages of the correct migrate-type to reduce the possibility of pages being inappropriate placed from a fragmentation perspective. This search is potentially expensive in a fast-path and undesirable. Splitting the per-cpu list into multiple lists increases the size of a per-cpu structure and this was potentially a major problem at the time the search was introduced. These problem has been mitigated as now only the necessary number of structures is allocated for the running system. This patch replaces a list search in the per-cpu allocator with one list per migrate type. The potential snag with this approach is when bulk freeing pages. We round-robin free pages based on migrate type which has little bearing on the cache hotness of the page and potentially checks empty lists repeatedly in the event the majority of PCP pages are of one type. Signed-off-by: Mel Gorman <mel@csn.ul.ie> Acked-by: Nick Piggin <npiggin@suse.de> Cc: Christoph Lameter <cl@linux-foundation.org> Cc: Minchan Kim <minchan.kim@gmail.com> Cc: Pekka Enberg <penberg@cs.helsinki.fi> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-22 07:03:19 +07:00
/* Lists of pages, one per migrate type stored on the pcp-lists */
struct list_head lists[MIGRATE_PCPTYPES];
};
struct per_cpu_pageset {
struct per_cpu_pages pcp;
Move remote node draining out of slab allocators Currently the slab allocators contain callbacks into the page allocator to perform the draining of pagesets on remote nodes. This requires SLUB to have a whole subsystem in order to be compatible with SLAB. Moving node draining out of the slab allocators avoids a section of code in SLUB. Move the node draining so that is is done when the vm statistics are updated. At that point we are already touching all the cachelines with the pagesets of a processor. Add a expire counter there. If we have to update per zone or global vm statistics then assume that the pageset will require subsequent draining. The expire counter will be decremented on each vm stats update pass until it reaches zero. Then we will drain one batch from the pageset. The draining will cause vm counter updates which will then cause another expiration until the pcp is empty. So we will drain a batch every 3 seconds. Note that remote node draining is a somewhat esoteric feature that is required on large NUMA systems because otherwise significant portions of system memory can become trapped in pcp queues. The number of pcp is determined by the number of processors and nodes in a system. A system with 4 processors and 2 nodes has 8 pcps which is okay. But a system with 1024 processors and 512 nodes has 512k pcps with a high potential for large amount of memory being caught in them. Signed-off-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-09 16:35:14 +07:00
#ifdef CONFIG_NUMA
s8 expire;
#endif
[PATCH] zoned vm counters: basic ZVC (zoned vm counter) implementation Per zone counter infrastructure The counters that we currently have for the VM are split per processor. The processor however has not much to do with the zone these pages belong to. We cannot tell f.e. how many ZONE_DMA pages are dirty. So we are blind to potentially inbalances in the usage of memory in various zones. F.e. in a NUMA system we cannot tell how many pages are dirty on a particular node. If we knew then we could put measures into the VM to balance the use of memory between different zones and different nodes in a NUMA system. For example it would be possible to limit the dirty pages per node so that fast local memory is kept available even if a process is dirtying huge amounts of pages. Another example is zone reclaim. We do not know how many unmapped pages exist per zone. So we just have to try to reclaim. If it is not working then we pause and try again later. It would be better if we knew when it makes sense to reclaim unmapped pages from a zone. This patchset allows the determination of the number of unmapped pages per zone. We can remove the zone reclaim interval with the counters introduced here. Futhermore the ability to have various usage statistics available will allow the development of new NUMA balancing algorithms that may be able to improve the decision making in the scheduler of when to move a process to another node and hopefully will also enable automatic page migration through a user space program that can analyse the memory load distribution and then rebalance memory use in order to increase performance. The counter framework here implements differential counters for each processor in struct zone. The differential counters are consolidated when a threshold is exceeded (like done in the current implementation for nr_pageache), when slab reaping occurs or when a consolidation function is called. Consolidation uses atomic operations and accumulates counters per zone in the zone structure and also globally in the vm_stat array. VM functions can access the counts by simply indexing a global or zone specific array. The arrangement of counters in an array also simplifies processing when output has to be generated for /proc/*. Counters can be updated by calling inc/dec_zone_page_state or _inc/dec_zone_page_state analogous to *_page_state. The second group of functions can be called if it is known that interrupts are disabled. Special optimized increment and decrement functions are provided. These can avoid certain checks and use increment or decrement instructions that an architecture may provide. We also add a new CONFIG_DMA_IS_NORMAL that signifies that an architecture can do DMA to all memory and therefore ZONE_NORMAL will not be populated. This is only currently set for IA64 SGI SN2 and currently only affects node_page_state(). In the best case node_page_state can be reduced to retrieving a single counter for the one zone on the node. [akpm@osdl.org: cleanups] [akpm@osdl.org: export vm_stat[] for filesystems] Signed-off-by: Christoph Lameter <clameter@sgi.com> Cc: Trond Myklebust <trond.myklebust@fys.uio.no> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-30 15:55:33 +07:00
#ifdef CONFIG_SMP
[PATCH] ZVC: Scale thresholds depending on the size of the system The ZVC counter update threshold is currently set to a fixed value of 32. This patch sets up the threshold depending on the number of processors and the sizes of the zones in the system. With the current threshold of 32, I was able to observe slight contention when more than 130-140 processors concurrently updated the counters. The contention vanished when I either increased the threshold to 64 or used Andrew's idea of overstepping the interval (see ZVC overstep patch). However, we saw contention again at 220-230 processors. So we need higher values for larger systems. But the current default is already a bit of an overkill for smaller systems. Some systems have tiny zones where precision matters. For example i386 and x86_64 have 16M DMA zones and either 900M ZONE_NORMAL or ZONE_DMA32. These are even present on SMP and NUMA systems. The patch here sets up a threshold based on the number of processors in the system and the size of the zone that these counters are used for. The threshold should grow logarithmically, so we use fls() as an easy approximation. Results of tests on a system with 1024 processors (4TB RAM) The following output is from a test allocating 1GB of memory concurrently on each processor (Forking the process. So contention on mmap_sem and the pte locks is not a factor): X MIN TYPE: CPUS WALL WALL SYS USER TOTCPU fork 1 0.552 0.552 0.540 0.012 0.552 fork 4 0.552 0.548 2.164 0.036 2.200 fork 16 0.564 0.548 8.812 0.164 8.976 fork 128 0.580 0.572 72.204 1.208 73.412 fork 256 1.300 0.660 310.400 2.160 312.560 fork 512 3.512 0.696 1526.836 4.816 1531.652 fork 1020 20.024 0.700 17243.176 6.688 17249.863 So a threshold of 32 is fine up to 128 processors. At 256 processors contention becomes a factor. Overstepping the counter (earlier patch) improves the numbers a bit: fork 4 0.552 0.548 2.164 0.040 2.204 fork 16 0.552 0.548 8.640 0.148 8.788 fork 128 0.556 0.548 69.676 0.956 70.632 fork 256 0.876 0.636 212.468 2.108 214.576 fork 512 2.276 0.672 997.324 4.260 1001.584 fork 1020 13.564 0.680 11586.436 6.088 11592.523 Still contention at 512 and 1020. Contention at 1020 is down by a third. 256 still has a slight bit of contention. After this patch the counter threshold will be set to 125 which reduces contention significantly: fork 128 0.560 0.548 69.776 0.932 70.708 fork 256 0.636 0.556 143.460 2.036 145.496 fork 512 0.640 0.548 284.244 4.236 288.480 fork 1020 1.500 0.588 1326.152 8.892 1335.044 [akpm@osdl.org: !SMP build fix] Signed-off-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-09-01 11:27:35 +07:00
s8 stat_threshold;
[PATCH] zoned vm counters: basic ZVC (zoned vm counter) implementation Per zone counter infrastructure The counters that we currently have for the VM are split per processor. The processor however has not much to do with the zone these pages belong to. We cannot tell f.e. how many ZONE_DMA pages are dirty. So we are blind to potentially inbalances in the usage of memory in various zones. F.e. in a NUMA system we cannot tell how many pages are dirty on a particular node. If we knew then we could put measures into the VM to balance the use of memory between different zones and different nodes in a NUMA system. For example it would be possible to limit the dirty pages per node so that fast local memory is kept available even if a process is dirtying huge amounts of pages. Another example is zone reclaim. We do not know how many unmapped pages exist per zone. So we just have to try to reclaim. If it is not working then we pause and try again later. It would be better if we knew when it makes sense to reclaim unmapped pages from a zone. This patchset allows the determination of the number of unmapped pages per zone. We can remove the zone reclaim interval with the counters introduced here. Futhermore the ability to have various usage statistics available will allow the development of new NUMA balancing algorithms that may be able to improve the decision making in the scheduler of when to move a process to another node and hopefully will also enable automatic page migration through a user space program that can analyse the memory load distribution and then rebalance memory use in order to increase performance. The counter framework here implements differential counters for each processor in struct zone. The differential counters are consolidated when a threshold is exceeded (like done in the current implementation for nr_pageache), when slab reaping occurs or when a consolidation function is called. Consolidation uses atomic operations and accumulates counters per zone in the zone structure and also globally in the vm_stat array. VM functions can access the counts by simply indexing a global or zone specific array. The arrangement of counters in an array also simplifies processing when output has to be generated for /proc/*. Counters can be updated by calling inc/dec_zone_page_state or _inc/dec_zone_page_state analogous to *_page_state. The second group of functions can be called if it is known that interrupts are disabled. Special optimized increment and decrement functions are provided. These can avoid certain checks and use increment or decrement instructions that an architecture may provide. We also add a new CONFIG_DMA_IS_NORMAL that signifies that an architecture can do DMA to all memory and therefore ZONE_NORMAL will not be populated. This is only currently set for IA64 SGI SN2 and currently only affects node_page_state(). In the best case node_page_state can be reduced to retrieving a single counter for the one zone on the node. [akpm@osdl.org: cleanups] [akpm@osdl.org: export vm_stat[] for filesystems] Signed-off-by: Christoph Lameter <clameter@sgi.com> Cc: Trond Myklebust <trond.myklebust@fys.uio.no> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-30 15:55:33 +07:00
s8 vm_stat_diff[NR_VM_ZONE_STAT_ITEMS];
#endif
};
[PATCH] node local per-cpu-pages This patch modifies the way pagesets in struct zone are managed. Each zone has a per-cpu array of pagesets. So any particular CPU has some memory in each zone structure which belongs to itself. Even if that CPU is not local to that zone. So the patch relocates the pagesets for each cpu to the node that is nearest to the cpu instead of allocating the pagesets in the (possibly remote) target zone. This means that the operations to manage pages on remote zone can be done with information available locally. We play a macro trick so that non-NUMA pmachines avoid the additional pointer chase on the page allocator fastpath. AIM7 benchmark on a 32 CPU SGI Altix w/o patches: Tasks jobs/min jti jobs/min/task real cpu 1 484.68 100 484.6769 12.01 1.97 Fri Mar 25 11:01:42 2005 100 27140.46 89 271.4046 21.44 148.71 Fri Mar 25 11:02:04 2005 200 30792.02 82 153.9601 37.80 296.72 Fri Mar 25 11:02:42 2005 300 32209.27 81 107.3642 54.21 451.34 Fri Mar 25 11:03:37 2005 400 34962.83 78 87.4071 66.59 588.97 Fri Mar 25 11:04:44 2005 500 31676.92 75 63.3538 91.87 742.71 Fri Mar 25 11:06:16 2005 600 36032.69 73 60.0545 96.91 885.44 Fri Mar 25 11:07:54 2005 700 35540.43 77 50.7720 114.63 1024.28 Fri Mar 25 11:09:49 2005 800 33906.70 74 42.3834 137.32 1181.65 Fri Mar 25 11:12:06 2005 900 34120.67 73 37.9119 153.51 1325.26 Fri Mar 25 11:14:41 2005 1000 34802.37 74 34.8024 167.23 1465.26 Fri Mar 25 11:17:28 2005 with slab API changes and pageset patch: Tasks jobs/min jti jobs/min/task real cpu 1 485.00 100 485.0000 12.00 1.96 Fri Mar 25 11:46:18 2005 100 28000.96 89 280.0096 20.79 150.45 Fri Mar 25 11:46:39 2005 200 32285.80 79 161.4290 36.05 293.37 Fri Mar 25 11:47:16 2005 300 40424.15 84 134.7472 43.19 438.42 Fri Mar 25 11:47:59 2005 400 39155.01 79 97.8875 59.46 590.05 Fri Mar 25 11:48:59 2005 500 37881.25 82 75.7625 76.82 730.19 Fri Mar 25 11:50:16 2005 600 39083.14 78 65.1386 89.35 872.79 Fri Mar 25 11:51:46 2005 700 38627.83 77 55.1826 105.47 1022.46 Fri Mar 25 11:53:32 2005 800 39631.94 78 49.5399 117.48 1169.94 Fri Mar 25 11:55:30 2005 900 36903.70 79 41.0041 141.94 1310.78 Fri Mar 25 11:57:53 2005 1000 36201.23 77 36.2012 160.77 1458.31 Fri Mar 25 12:00:34 2005 Signed-off-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Shobhit Dayal <shobhit@calsoftinc.com> Signed-off-by: Shai Fultheim <Shai@Scalex86.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-22 07:14:47 +07:00
#endif /* !__GENERATING_BOUNDS.H */
enum zone_type {
#ifdef CONFIG_ZONE_DMA
/*
* ZONE_DMA is used when there are devices that are not able
* to do DMA to all of addressable memory (ZONE_NORMAL). Then we
* carve out the portion of memory that is needed for these devices.
* The range is arch specific.
*
* Some examples
*
* Architecture Limit
* ---------------------------
* parisc, ia64, sparc <4G
* s390 <2G
* arm Various
* alpha Unlimited or 0-16MB.
*
* i386, x86_64 and multiple other arches
* <16M.
*/
ZONE_DMA,
#endif
#ifdef CONFIG_ZONE_DMA32
/*
* x86_64 needs two ZONE_DMAs because it supports devices that are
* only able to do DMA to the lower 16M but also 32 bit devices that
* can only do DMA areas below 4G.
*/
ZONE_DMA32,
#endif
/*
* Normal addressable memory is in ZONE_NORMAL. DMA operations can be
* performed on pages in ZONE_NORMAL if the DMA devices support
* transfers to all addressable memory.
*/
ZONE_NORMAL,
#ifdef CONFIG_HIGHMEM
/*
* A memory area that is only addressable by the kernel through
* mapping portions into its own address space. This is for example
* used by i386 to allow the kernel to address the memory beyond
* 900MB. The kernel will set up special mappings (page
* table entries on i386) for each page that the kernel needs to
* access.
*/
ZONE_HIGHMEM,
#endif
Create the ZONE_MOVABLE zone The following 8 patches against 2.6.20-mm2 create a zone called ZONE_MOVABLE that is only usable by allocations that specify both __GFP_HIGHMEM and __GFP_MOVABLE. This has the effect of keeping all non-movable pages within a single memory partition while allowing movable allocations to be satisfied from either partition. The patches may be applied with the list-based anti-fragmentation patches that groups pages together based on mobility. The size of the zone is determined by a kernelcore= parameter specified at boot-time. This specifies how much memory is usable by non-movable allocations and the remainder is used for ZONE_MOVABLE. Any range of pages within ZONE_MOVABLE can be released by migrating the pages or by reclaiming. When selecting a zone to take pages from for ZONE_MOVABLE, there are two things to consider. First, only memory from the highest populated zone is used for ZONE_MOVABLE. On the x86, this is probably going to be ZONE_HIGHMEM but it would be ZONE_DMA on ppc64 or possibly ZONE_DMA32 on x86_64. Second, the amount of memory usable by the kernel will be spread evenly throughout NUMA nodes where possible. If the nodes are not of equal size, the amount of memory usable by the kernel on some nodes may be greater than others. By default, the zone is not as useful for hugetlb allocations because they are pinned and non-migratable (currently at least). A sysctl is provided that allows huge pages to be allocated from that zone. This means that the huge page pool can be resized to the size of ZONE_MOVABLE during the lifetime of the system assuming that pages are not mlocked. Despite huge pages being non-movable, we do not introduce additional external fragmentation of note as huge pages are always the largest contiguous block we care about. Credit goes to Andy Whitcroft for catching a large variety of problems during review of the patches. This patch creates an additional zone, ZONE_MOVABLE. This zone is only usable by allocations which specify both __GFP_HIGHMEM and __GFP_MOVABLE. Hot-added memory continues to be placed in their existing destination as there is no mechanism to redirect them to a specific zone. [y-goto@jp.fujitsu.com: Fix section mismatch of memory hotplug related code] [akpm@linux-foundation.org: various fixes] Signed-off-by: Mel Gorman <mel@csn.ul.ie> Cc: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com> Cc: William Lee Irwin III <wli@holomorphy.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-17 18:03:12 +07:00
ZONE_MOVABLE,
__MAX_NR_ZONES
};
#ifndef __GENERATING_BOUNDS_H
struct zone {
mm: rearrange zone fields into read-only, page alloc, statistics and page reclaim lines The arrangement of struct zone has changed over time and now it has reached the point where there is some inappropriate sharing going on. On x86-64 for example o The zone->node field is shared with the zone lock and zone->node is accessed frequently from the page allocator due to the fair zone allocation policy. o span_seqlock is almost never used by shares a line with free_area o Some zone statistics share a cache line with the LRU lock so reclaim-intensive and allocator-intensive workloads can bounce the cache line on a stat update This patch rearranges struct zone to put read-only and read-mostly fields together and then splits the page allocator intensive fields, the zone statistics and the page reclaim intensive fields into their own cache lines. Note that the type of lowmem_reserve changes due to the watermark calculations being signed and avoiding a signed/unsigned conversion there. On the test configuration I used the overall size of struct zone shrunk by one cache line. On smaller machines, this is not likely to be noticable. However, on a 4-node NUMA machine running tiobench the system CPU overhead is reduced by this patch. 3.16.0-rc3 3.16.0-rc3 vanillarearrange-v5r9 User 746.94 759.78 System 65336.22 58350.98 Elapsed 27553.52 27282.02 Signed-off-by: Mel Gorman <mgorman@suse.de> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-08-07 06:07:14 +07:00
/* Read-mostly fields */
/* zone watermarks, access with *_wmark_pages(zone) macros */
unsigned long watermark[NR_WMARK];
/*
* We don't know if the memory that we're going to allocate will be freeable
* or/and it will be released eventually, so to avoid totally wasting several
* GB of ram we must reserve some of the lower zone memory (otherwise we risk
* to run OOM on the lower zones despite there's tons of freeable ram
* on the higher zones). This array is recalculated at runtime if the
* sysctl_lowmem_reserve_ratio sysctl changes.
*/
mm: rearrange zone fields into read-only, page alloc, statistics and page reclaim lines The arrangement of struct zone has changed over time and now it has reached the point where there is some inappropriate sharing going on. On x86-64 for example o The zone->node field is shared with the zone lock and zone->node is accessed frequently from the page allocator due to the fair zone allocation policy. o span_seqlock is almost never used by shares a line with free_area o Some zone statistics share a cache line with the LRU lock so reclaim-intensive and allocator-intensive workloads can bounce the cache line on a stat update This patch rearranges struct zone to put read-only and read-mostly fields together and then splits the page allocator intensive fields, the zone statistics and the page reclaim intensive fields into their own cache lines. Note that the type of lowmem_reserve changes due to the watermark calculations being signed and avoiding a signed/unsigned conversion there. On the test configuration I used the overall size of struct zone shrunk by one cache line. On smaller machines, this is not likely to be noticable. However, on a 4-node NUMA machine running tiobench the system CPU overhead is reduced by this patch. 3.16.0-rc3 3.16.0-rc3 vanillarearrange-v5r9 User 746.94 759.78 System 65336.22 58350.98 Elapsed 27553.52 27282.02 Signed-off-by: Mel Gorman <mgorman@suse.de> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-08-07 06:07:14 +07:00
long lowmem_reserve[MAX_NR_ZONES];
mm: exclude reserved pages from dirtyable memory Per-zone dirty limits try to distribute page cache pages allocated for writing across zones in proportion to the individual zone sizes, to reduce the likelihood of reclaim having to write back individual pages from the LRU lists in order to make progress. This patch: The amount of dirtyable pages should not include the full number of free pages: there is a number of reserved pages that the page allocator and kswapd always try to keep free. The closer (reclaimable pages - dirty pages) is to the number of reserved pages, the more likely it becomes for reclaim to run into dirty pages: +----------+ --- | anon | | +----------+ | | | | | | -- dirty limit new -- flusher new | file | | | | | | | | | -- dirty limit old -- flusher old | | | +----------+ --- reclaim | reserved | +----------+ | kernel | +----------+ This patch introduces a per-zone dirty reserve that takes both the lowmem reserve as well as the high watermark of the zone into account, and a global sum of those per-zone values that is subtracted from the global amount of dirtyable pages. The lowmem reserve is unavailable to page cache allocations and kswapd tries to keep the high watermark free. We don't want to end up in a situation where reclaim has to clean pages in order to balance zones. Not treating reserved pages as dirtyable on a global level is only a conceptual fix. In reality, dirty pages are not distributed equally across zones and reclaim runs into dirty pages on a regular basis. But it is important to get this right before tackling the problem on a per-zone level, where the distance between reclaim and the dirty pages is mostly much smaller in absolute numbers. [akpm@linux-foundation.org: fix highmem build] Signed-off-by: Johannes Weiner <jweiner@redhat.com> Reviewed-by: Rik van Riel <riel@redhat.com> Reviewed-by: Michal Hocko <mhocko@suse.cz> Reviewed-by: Minchan Kim <minchan.kim@gmail.com> Acked-by: Mel Gorman <mgorman@suse.de> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Wu Fengguang <fengguang.wu@intel.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Jan Kara <jack@suse.cz> Cc: Shaohua Li <shaohua.li@intel.com> Cc: Chris Mason <chris.mason@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-01-11 06:07:42 +07:00
[PATCH] node local per-cpu-pages This patch modifies the way pagesets in struct zone are managed. Each zone has a per-cpu array of pagesets. So any particular CPU has some memory in each zone structure which belongs to itself. Even if that CPU is not local to that zone. So the patch relocates the pagesets for each cpu to the node that is nearest to the cpu instead of allocating the pagesets in the (possibly remote) target zone. This means that the operations to manage pages on remote zone can be done with information available locally. We play a macro trick so that non-NUMA pmachines avoid the additional pointer chase on the page allocator fastpath. AIM7 benchmark on a 32 CPU SGI Altix w/o patches: Tasks jobs/min jti jobs/min/task real cpu 1 484.68 100 484.6769 12.01 1.97 Fri Mar 25 11:01:42 2005 100 27140.46 89 271.4046 21.44 148.71 Fri Mar 25 11:02:04 2005 200 30792.02 82 153.9601 37.80 296.72 Fri Mar 25 11:02:42 2005 300 32209.27 81 107.3642 54.21 451.34 Fri Mar 25 11:03:37 2005 400 34962.83 78 87.4071 66.59 588.97 Fri Mar 25 11:04:44 2005 500 31676.92 75 63.3538 91.87 742.71 Fri Mar 25 11:06:16 2005 600 36032.69 73 60.0545 96.91 885.44 Fri Mar 25 11:07:54 2005 700 35540.43 77 50.7720 114.63 1024.28 Fri Mar 25 11:09:49 2005 800 33906.70 74 42.3834 137.32 1181.65 Fri Mar 25 11:12:06 2005 900 34120.67 73 37.9119 153.51 1325.26 Fri Mar 25 11:14:41 2005 1000 34802.37 74 34.8024 167.23 1465.26 Fri Mar 25 11:17:28 2005 with slab API changes and pageset patch: Tasks jobs/min jti jobs/min/task real cpu 1 485.00 100 485.0000 12.00 1.96 Fri Mar 25 11:46:18 2005 100 28000.96 89 280.0096 20.79 150.45 Fri Mar 25 11:46:39 2005 200 32285.80 79 161.4290 36.05 293.37 Fri Mar 25 11:47:16 2005 300 40424.15 84 134.7472 43.19 438.42 Fri Mar 25 11:47:59 2005 400 39155.01 79 97.8875 59.46 590.05 Fri Mar 25 11:48:59 2005 500 37881.25 82 75.7625 76.82 730.19 Fri Mar 25 11:50:16 2005 600 39083.14 78 65.1386 89.35 872.79 Fri Mar 25 11:51:46 2005 700 38627.83 77 55.1826 105.47 1022.46 Fri Mar 25 11:53:32 2005 800 39631.94 78 49.5399 117.48 1169.94 Fri Mar 25 11:55:30 2005 900 36903.70 79 41.0041 141.94 1310.78 Fri Mar 25 11:57:53 2005 1000 36201.23 77 36.2012 160.77 1458.31 Fri Mar 25 12:00:34 2005 Signed-off-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Shobhit Dayal <shobhit@calsoftinc.com> Signed-off-by: Shai Fultheim <Shai@Scalex86.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-22 07:14:47 +07:00
#ifdef CONFIG_NUMA
int node;
mm: rearrange zone fields into read-only, page alloc, statistics and page reclaim lines The arrangement of struct zone has changed over time and now it has reached the point where there is some inappropriate sharing going on. On x86-64 for example o The zone->node field is shared with the zone lock and zone->node is accessed frequently from the page allocator due to the fair zone allocation policy. o span_seqlock is almost never used by shares a line with free_area o Some zone statistics share a cache line with the LRU lock so reclaim-intensive and allocator-intensive workloads can bounce the cache line on a stat update This patch rearranges struct zone to put read-only and read-mostly fields together and then splits the page allocator intensive fields, the zone statistics and the page reclaim intensive fields into their own cache lines. Note that the type of lowmem_reserve changes due to the watermark calculations being signed and avoiding a signed/unsigned conversion there. On the test configuration I used the overall size of struct zone shrunk by one cache line. On smaller machines, this is not likely to be noticable. However, on a 4-node NUMA machine running tiobench the system CPU overhead is reduced by this patch. 3.16.0-rc3 3.16.0-rc3 vanillarearrange-v5r9 User 746.94 759.78 System 65336.22 58350.98 Elapsed 27553.52 27282.02 Signed-off-by: Mel Gorman <mgorman@suse.de> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-08-07 06:07:14 +07:00
#endif
/*
mm: rearrange zone fields into read-only, page alloc, statistics and page reclaim lines The arrangement of struct zone has changed over time and now it has reached the point where there is some inappropriate sharing going on. On x86-64 for example o The zone->node field is shared with the zone lock and zone->node is accessed frequently from the page allocator due to the fair zone allocation policy. o span_seqlock is almost never used by shares a line with free_area o Some zone statistics share a cache line with the LRU lock so reclaim-intensive and allocator-intensive workloads can bounce the cache line on a stat update This patch rearranges struct zone to put read-only and read-mostly fields together and then splits the page allocator intensive fields, the zone statistics and the page reclaim intensive fields into their own cache lines. Note that the type of lowmem_reserve changes due to the watermark calculations being signed and avoiding a signed/unsigned conversion there. On the test configuration I used the overall size of struct zone shrunk by one cache line. On smaller machines, this is not likely to be noticable. However, on a 4-node NUMA machine running tiobench the system CPU overhead is reduced by this patch. 3.16.0-rc3 3.16.0-rc3 vanillarearrange-v5r9 User 746.94 759.78 System 65336.22 58350.98 Elapsed 27553.52 27282.02 Signed-off-by: Mel Gorman <mgorman@suse.de> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-08-07 06:07:14 +07:00
* The target ratio of ACTIVE_ANON to INACTIVE_ANON pages on
* this zone's LRU. Maintained by the pageout code.
*/
mm: rearrange zone fields into read-only, page alloc, statistics and page reclaim lines The arrangement of struct zone has changed over time and now it has reached the point where there is some inappropriate sharing going on. On x86-64 for example o The zone->node field is shared with the zone lock and zone->node is accessed frequently from the page allocator due to the fair zone allocation policy. o span_seqlock is almost never used by shares a line with free_area o Some zone statistics share a cache line with the LRU lock so reclaim-intensive and allocator-intensive workloads can bounce the cache line on a stat update This patch rearranges struct zone to put read-only and read-mostly fields together and then splits the page allocator intensive fields, the zone statistics and the page reclaim intensive fields into their own cache lines. Note that the type of lowmem_reserve changes due to the watermark calculations being signed and avoiding a signed/unsigned conversion there. On the test configuration I used the overall size of struct zone shrunk by one cache line. On smaller machines, this is not likely to be noticable. However, on a 4-node NUMA machine running tiobench the system CPU overhead is reduced by this patch. 3.16.0-rc3 3.16.0-rc3 vanillarearrange-v5r9 User 746.94 759.78 System 65336.22 58350.98 Elapsed 27553.52 27282.02 Signed-off-by: Mel Gorman <mgorman@suse.de> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-08-07 06:07:14 +07:00
unsigned int inactive_ratio;
struct pglist_data *zone_pgdat;
struct per_cpu_pageset __percpu *pageset;
mm: rearrange zone fields into read-only, page alloc, statistics and page reclaim lines The arrangement of struct zone has changed over time and now it has reached the point where there is some inappropriate sharing going on. On x86-64 for example o The zone->node field is shared with the zone lock and zone->node is accessed frequently from the page allocator due to the fair zone allocation policy. o span_seqlock is almost never used by shares a line with free_area o Some zone statistics share a cache line with the LRU lock so reclaim-intensive and allocator-intensive workloads can bounce the cache line on a stat update This patch rearranges struct zone to put read-only and read-mostly fields together and then splits the page allocator intensive fields, the zone statistics and the page reclaim intensive fields into their own cache lines. Note that the type of lowmem_reserve changes due to the watermark calculations being signed and avoiding a signed/unsigned conversion there. On the test configuration I used the overall size of struct zone shrunk by one cache line. On smaller machines, this is not likely to be noticable. However, on a 4-node NUMA machine running tiobench the system CPU overhead is reduced by this patch. 3.16.0-rc3 3.16.0-rc3 vanillarearrange-v5r9 User 746.94 759.78 System 65336.22 58350.98 Elapsed 27553.52 27282.02 Signed-off-by: Mel Gorman <mgorman@suse.de> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-08-07 06:07:14 +07:00
/*
mm: rearrange zone fields into read-only, page alloc, statistics and page reclaim lines The arrangement of struct zone has changed over time and now it has reached the point where there is some inappropriate sharing going on. On x86-64 for example o The zone->node field is shared with the zone lock and zone->node is accessed frequently from the page allocator due to the fair zone allocation policy. o span_seqlock is almost never used by shares a line with free_area o Some zone statistics share a cache line with the LRU lock so reclaim-intensive and allocator-intensive workloads can bounce the cache line on a stat update This patch rearranges struct zone to put read-only and read-mostly fields together and then splits the page allocator intensive fields, the zone statistics and the page reclaim intensive fields into their own cache lines. Note that the type of lowmem_reserve changes due to the watermark calculations being signed and avoiding a signed/unsigned conversion there. On the test configuration I used the overall size of struct zone shrunk by one cache line. On smaller machines, this is not likely to be noticable. However, on a 4-node NUMA machine running tiobench the system CPU overhead is reduced by this patch. 3.16.0-rc3 3.16.0-rc3 vanillarearrange-v5r9 User 746.94 759.78 System 65336.22 58350.98 Elapsed 27553.52 27282.02 Signed-off-by: Mel Gorman <mgorman@suse.de> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-08-07 06:07:14 +07:00
* This is a per-zone reserve of pages that should not be
* considered dirtyable memory.
*/
mm: rearrange zone fields into read-only, page alloc, statistics and page reclaim lines The arrangement of struct zone has changed over time and now it has reached the point where there is some inappropriate sharing going on. On x86-64 for example o The zone->node field is shared with the zone lock and zone->node is accessed frequently from the page allocator due to the fair zone allocation policy. o span_seqlock is almost never used by shares a line with free_area o Some zone statistics share a cache line with the LRU lock so reclaim-intensive and allocator-intensive workloads can bounce the cache line on a stat update This patch rearranges struct zone to put read-only and read-mostly fields together and then splits the page allocator intensive fields, the zone statistics and the page reclaim intensive fields into their own cache lines. Note that the type of lowmem_reserve changes due to the watermark calculations being signed and avoiding a signed/unsigned conversion there. On the test configuration I used the overall size of struct zone shrunk by one cache line. On smaller machines, this is not likely to be noticable. However, on a 4-node NUMA machine running tiobench the system CPU overhead is reduced by this patch. 3.16.0-rc3 3.16.0-rc3 vanillarearrange-v5r9 User 746.94 759.78 System 65336.22 58350.98 Elapsed 27553.52 27282.02 Signed-off-by: Mel Gorman <mgorman@suse.de> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-08-07 06:07:14 +07:00
unsigned long dirty_balance_reserve;
Add a bitmap that is used to track flags affecting a block of pages Here is the latest revision of the anti-fragmentation patches. Of particular note in this version is special treatment of high-order atomic allocations. Care is taken to group them together and avoid grouping pages of other types near them. Artifical tests imply that it works. I'm trying to get the hardware together that would allow setting up of a "real" test. If anyone already has a setup and test that can trigger the atomic-allocation problem, I'd appreciate a test of these patches and a report. The second major change is that these patches will apply cleanly with patches that implement anti-fragmentation through zones. kernbench shows effectively no performance difference varying between -0.2% and +2% on a variety of test machines. Success rates for huge page allocation are dramatically increased. For example, on a ppc64 machine, the vanilla kernel was only able to allocate 1% of memory as a hugepage and this was due to a single hugepage reserved as min_free_kbytes. With these patches applied, 17% was allocatable as superpages. With reclaim-related fixes from Andy Whitcroft, it was 40% and further reclaim-related improvements should increase this further. Changelog Since V28 o Group high-order atomic allocations together o It is no longer required to set min_free_kbytes to 10% of memory. A value of 16384 in most cases will be sufficient o Now applied with zone-based anti-fragmentation o Fix incorrect VM_BUG_ON within buffered_rmqueue() o Reorder the stack so later patches do not back out work from earlier patches o Fix bug were journal pages were being treated as movable o Bias placement of non-movable pages to lower PFNs o More agressive clustering of reclaimable pages in reactions to workloads like updatedb that flood the size of inode caches Changelog Since V27 o Renamed anti-fragmentation to Page Clustering. Anti-fragmentation was giving the mistaken impression that it was the 100% solution for high order allocations. Instead, it greatly increases the chances high-order allocations will succeed and lays the foundation for defragmentation and memory hot-remove to work properly o Redefine page groupings based on ability to migrate or reclaim instead of basing on reclaimability alone o Get rid of spurious inits o Per-cpu lists are no longer split up per-type. Instead the per-cpu list is searched for a page of the appropriate type o Added more explanation commentary o Fix up bug in pageblock code where bitmap was used before being initalised Changelog Since V26 o Fix double init of lists in setup_pageset Changelog Since V25 o Fix loop order of for_each_rclmtype_order so that order of loop matches args o gfpflags_to_rclmtype uses gfp_t instead of unsigned long o Rename get_pageblock_type() to get_page_rclmtype() o Fix alignment problem in move_freepages() o Add mechanism for assigning flags to blocks of pages instead of page->flags o On fallback, do not examine the preferred list of free pages a second time The purpose of these patches is to reduce external fragmentation by grouping pages of related types together. When pages are migrated (or reclaimed under memory pressure), large contiguous pages will be freed. This patch works by categorising allocations by their ability to migrate; Movable - The pages may be moved with the page migration mechanism. These are generally userspace pages. Reclaimable - These are allocations for some kernel caches that are reclaimable or allocations that are known to be very short-lived. Unmovable - These are pages that are allocated by the kernel that are not trivially reclaimed. For example, the memory allocated for a loaded module would be in this category. By default, allocations are considered to be of this type HighAtomic - These are high-order allocations belonging to callers that cannot sleep or perform any IO. In practice, this is restricted to jumbo frame allocation for network receive. It is assumed that the allocations are short-lived Instead of having one MAX_ORDER-sized array of free lists in struct free_area, there is one for each type of reclaimability. Once a 2^MAX_ORDER block of pages is split for a type of allocation, it is added to the free-lists for that type, in effect reserving it. Hence, over time, pages of the different types can be clustered together. When the preferred freelists are expired, the largest possible block is taken from an alternative list. Buddies that are split from that large block are placed on the preferred allocation-type freelists to mitigate fragmentation. This implementation gives best-effort for low fragmentation in all zones. Ideally, min_free_kbytes needs to be set to a value equal to 4 * (1 << (MAX_ORDER-1)) pages in most cases. This would be 16384 on x86 and x86_64 for example. Our tests show that about 60-70% of physical memory can be allocated on a desktop after a few days uptime. In benchmarks and stress tests, we are finding that 80% of memory is available as contiguous blocks at the end of the test. To compare, a standard kernel was getting < 1% of memory as large pages on a desktop and about 8-12% of memory as large pages at the end of stress tests. Following this email are 12 patches that implement thie page grouping feature. The first patch introduces a mechanism for storing flags related to a whole block of pages. Then allocations are split between movable and all other allocations. Following that are patches to deal with per-cpu pages and make the mechanism configurable. The next patch moves free pages between lists when partially allocated blocks are used for pages of another migrate type. The second last patch groups reclaimable kernel allocations such as inode caches together. The final patch related to groupings keeps high-order atomic allocations. The last two patches are more concerned with control of fragmentation. The second last patch biases placement of non-movable allocations towards the start of memory. This is with a view of supporting memory hot-remove of DIMMs with higher PFNs in the future. The biasing could be enforced a lot heavier but it would cost. The last patch agressively clusters reclaimable pages like inode caches together. The fragmentation reduction strategy needs to track if pages within a block can be moved or reclaimed so that pages are freed to the appropriate list. This patch adds a bitmap for flags affecting a whole a MAX_ORDER block of pages. In non-SPARSEMEM configurations, the bitmap is stored in the struct zone and allocated during initialisation. SPARSEMEM statically allocates the bitmap in a struct mem_section so that bitmaps do not have to be resized during memory hotadd. This wastes a small amount of memory per unused section (usually sizeof(unsigned long)) but the complexity of dynamically allocating the memory is quite high. Additional credit to Andy Whitcroft who reviewed up an earlier implementation of the mechanism an suggested how to make it a *lot* cleaner. Signed-off-by: Mel Gorman <mel@csn.ul.ie> Cc: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16 15:25:47 +07:00
#ifndef CONFIG_SPARSEMEM
/*
Do not depend on MAX_ORDER when grouping pages by mobility Currently mobility grouping works at the MAX_ORDER_NR_PAGES level. This makes sense for the majority of users where this is also the huge page size. However, on platforms like ia64 where the huge page size is runtime configurable it is desirable to group at a lower order. On x86_64 and occasionally on x86, the hugepage size may not always be MAX_ORDER_NR_PAGES. This patch groups pages together based on the value of HUGETLB_PAGE_ORDER. It uses a compile-time constant if possible and a variable where the huge page size is runtime configurable. It is assumed that grouping should be done at the lowest sensible order and that the user would not want to override this. If this is not true, page_block order could be forced to a variable initialised via a boot-time kernel parameter. One potential issue with this patch is that IA64 now parses hugepagesz with early_param() instead of __setup(). __setup() is called after the memory allocator has been initialised and the pageblock bitmaps already setup. In tests on one IA64 there did not seem to be any problem with using early_param() and in fact may be more correct as it guarantees the parameter is handled before the parsing of hugepages=. Signed-off-by: Mel Gorman <mel@csn.ul.ie> Acked-by: Andy Whitcroft <apw@shadowen.org> Acked-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16 15:26:01 +07:00
* Flags for a pageblock_nr_pages block. See pageblock-flags.h.
Add a bitmap that is used to track flags affecting a block of pages Here is the latest revision of the anti-fragmentation patches. Of particular note in this version is special treatment of high-order atomic allocations. Care is taken to group them together and avoid grouping pages of other types near them. Artifical tests imply that it works. I'm trying to get the hardware together that would allow setting up of a "real" test. If anyone already has a setup and test that can trigger the atomic-allocation problem, I'd appreciate a test of these patches and a report. The second major change is that these patches will apply cleanly with patches that implement anti-fragmentation through zones. kernbench shows effectively no performance difference varying between -0.2% and +2% on a variety of test machines. Success rates for huge page allocation are dramatically increased. For example, on a ppc64 machine, the vanilla kernel was only able to allocate 1% of memory as a hugepage and this was due to a single hugepage reserved as min_free_kbytes. With these patches applied, 17% was allocatable as superpages. With reclaim-related fixes from Andy Whitcroft, it was 40% and further reclaim-related improvements should increase this further. Changelog Since V28 o Group high-order atomic allocations together o It is no longer required to set min_free_kbytes to 10% of memory. A value of 16384 in most cases will be sufficient o Now applied with zone-based anti-fragmentation o Fix incorrect VM_BUG_ON within buffered_rmqueue() o Reorder the stack so later patches do not back out work from earlier patches o Fix bug were journal pages were being treated as movable o Bias placement of non-movable pages to lower PFNs o More agressive clustering of reclaimable pages in reactions to workloads like updatedb that flood the size of inode caches Changelog Since V27 o Renamed anti-fragmentation to Page Clustering. Anti-fragmentation was giving the mistaken impression that it was the 100% solution for high order allocations. Instead, it greatly increases the chances high-order allocations will succeed and lays the foundation for defragmentation and memory hot-remove to work properly o Redefine page groupings based on ability to migrate or reclaim instead of basing on reclaimability alone o Get rid of spurious inits o Per-cpu lists are no longer split up per-type. Instead the per-cpu list is searched for a page of the appropriate type o Added more explanation commentary o Fix up bug in pageblock code where bitmap was used before being initalised Changelog Since V26 o Fix double init of lists in setup_pageset Changelog Since V25 o Fix loop order of for_each_rclmtype_order so that order of loop matches args o gfpflags_to_rclmtype uses gfp_t instead of unsigned long o Rename get_pageblock_type() to get_page_rclmtype() o Fix alignment problem in move_freepages() o Add mechanism for assigning flags to blocks of pages instead of page->flags o On fallback, do not examine the preferred list of free pages a second time The purpose of these patches is to reduce external fragmentation by grouping pages of related types together. When pages are migrated (or reclaimed under memory pressure), large contiguous pages will be freed. This patch works by categorising allocations by their ability to migrate; Movable - The pages may be moved with the page migration mechanism. These are generally userspace pages. Reclaimable - These are allocations for some kernel caches that are reclaimable or allocations that are known to be very short-lived. Unmovable - These are pages that are allocated by the kernel that are not trivially reclaimed. For example, the memory allocated for a loaded module would be in this category. By default, allocations are considered to be of this type HighAtomic - These are high-order allocations belonging to callers that cannot sleep or perform any IO. In practice, this is restricted to jumbo frame allocation for network receive. It is assumed that the allocations are short-lived Instead of having one MAX_ORDER-sized array of free lists in struct free_area, there is one for each type of reclaimability. Once a 2^MAX_ORDER block of pages is split for a type of allocation, it is added to the free-lists for that type, in effect reserving it. Hence, over time, pages of the different types can be clustered together. When the preferred freelists are expired, the largest possible block is taken from an alternative list. Buddies that are split from that large block are placed on the preferred allocation-type freelists to mitigate fragmentation. This implementation gives best-effort for low fragmentation in all zones. Ideally, min_free_kbytes needs to be set to a value equal to 4 * (1 << (MAX_ORDER-1)) pages in most cases. This would be 16384 on x86 and x86_64 for example. Our tests show that about 60-70% of physical memory can be allocated on a desktop after a few days uptime. In benchmarks and stress tests, we are finding that 80% of memory is available as contiguous blocks at the end of the test. To compare, a standard kernel was getting < 1% of memory as large pages on a desktop and about 8-12% of memory as large pages at the end of stress tests. Following this email are 12 patches that implement thie page grouping feature. The first patch introduces a mechanism for storing flags related to a whole block of pages. Then allocations are split between movable and all other allocations. Following that are patches to deal with per-cpu pages and make the mechanism configurable. The next patch moves free pages between lists when partially allocated blocks are used for pages of another migrate type. The second last patch groups reclaimable kernel allocations such as inode caches together. The final patch related to groupings keeps high-order atomic allocations. The last two patches are more concerned with control of fragmentation. The second last patch biases placement of non-movable allocations towards the start of memory. This is with a view of supporting memory hot-remove of DIMMs with higher PFNs in the future. The biasing could be enforced a lot heavier but it would cost. The last patch agressively clusters reclaimable pages like inode caches together. The fragmentation reduction strategy needs to track if pages within a block can be moved or reclaimed so that pages are freed to the appropriate list. This patch adds a bitmap for flags affecting a whole a MAX_ORDER block of pages. In non-SPARSEMEM configurations, the bitmap is stored in the struct zone and allocated during initialisation. SPARSEMEM statically allocates the bitmap in a struct mem_section so that bitmaps do not have to be resized during memory hotadd. This wastes a small amount of memory per unused section (usually sizeof(unsigned long)) but the complexity of dynamically allocating the memory is quite high. Additional credit to Andy Whitcroft who reviewed up an earlier implementation of the mechanism an suggested how to make it a *lot* cleaner. Signed-off-by: Mel Gorman <mel@csn.ul.ie> Cc: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16 15:25:47 +07:00
* In SPARSEMEM, this map is stored in struct mem_section
*/
unsigned long *pageblock_flags;
#endif /* CONFIG_SPARSEMEM */
mm: rearrange zone fields into read-only, page alloc, statistics and page reclaim lines The arrangement of struct zone has changed over time and now it has reached the point where there is some inappropriate sharing going on. On x86-64 for example o The zone->node field is shared with the zone lock and zone->node is accessed frequently from the page allocator due to the fair zone allocation policy. o span_seqlock is almost never used by shares a line with free_area o Some zone statistics share a cache line with the LRU lock so reclaim-intensive and allocator-intensive workloads can bounce the cache line on a stat update This patch rearranges struct zone to put read-only and read-mostly fields together and then splits the page allocator intensive fields, the zone statistics and the page reclaim intensive fields into their own cache lines. Note that the type of lowmem_reserve changes due to the watermark calculations being signed and avoiding a signed/unsigned conversion there. On the test configuration I used the overall size of struct zone shrunk by one cache line. On smaller machines, this is not likely to be noticable. However, on a 4-node NUMA machine running tiobench the system CPU overhead is reduced by this patch. 3.16.0-rc3 3.16.0-rc3 vanillarearrange-v5r9 User 746.94 759.78 System 65336.22 58350.98 Elapsed 27553.52 27282.02 Signed-off-by: Mel Gorman <mgorman@suse.de> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-08-07 06:07:14 +07:00
#ifdef CONFIG_NUMA
/*
mm: rearrange zone fields into read-only, page alloc, statistics and page reclaim lines The arrangement of struct zone has changed over time and now it has reached the point where there is some inappropriate sharing going on. On x86-64 for example o The zone->node field is shared with the zone lock and zone->node is accessed frequently from the page allocator due to the fair zone allocation policy. o span_seqlock is almost never used by shares a line with free_area o Some zone statistics share a cache line with the LRU lock so reclaim-intensive and allocator-intensive workloads can bounce the cache line on a stat update This patch rearranges struct zone to put read-only and read-mostly fields together and then splits the page allocator intensive fields, the zone statistics and the page reclaim intensive fields into their own cache lines. Note that the type of lowmem_reserve changes due to the watermark calculations being signed and avoiding a signed/unsigned conversion there. On the test configuration I used the overall size of struct zone shrunk by one cache line. On smaller machines, this is not likely to be noticable. However, on a 4-node NUMA machine running tiobench the system CPU overhead is reduced by this patch. 3.16.0-rc3 3.16.0-rc3 vanillarearrange-v5r9 User 746.94 759.78 System 65336.22 58350.98 Elapsed 27553.52 27282.02 Signed-off-by: Mel Gorman <mgorman@suse.de> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-08-07 06:07:14 +07:00
* zone reclaim becomes active if more unmapped pages exist.
*/
mm: rearrange zone fields into read-only, page alloc, statistics and page reclaim lines The arrangement of struct zone has changed over time and now it has reached the point where there is some inappropriate sharing going on. On x86-64 for example o The zone->node field is shared with the zone lock and zone->node is accessed frequently from the page allocator due to the fair zone allocation policy. o span_seqlock is almost never used by shares a line with free_area o Some zone statistics share a cache line with the LRU lock so reclaim-intensive and allocator-intensive workloads can bounce the cache line on a stat update This patch rearranges struct zone to put read-only and read-mostly fields together and then splits the page allocator intensive fields, the zone statistics and the page reclaim intensive fields into their own cache lines. Note that the type of lowmem_reserve changes due to the watermark calculations being signed and avoiding a signed/unsigned conversion there. On the test configuration I used the overall size of struct zone shrunk by one cache line. On smaller machines, this is not likely to be noticable. However, on a 4-node NUMA machine running tiobench the system CPU overhead is reduced by this patch. 3.16.0-rc3 3.16.0-rc3 vanillarearrange-v5r9 User 746.94 759.78 System 65336.22 58350.98 Elapsed 27553.52 27282.02 Signed-off-by: Mel Gorman <mgorman@suse.de> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-08-07 06:07:14 +07:00
unsigned long min_unmapped_pages;
unsigned long min_slab_pages;
#endif /* CONFIG_NUMA */
/* zone_start_pfn == zone_start_paddr >> PAGE_SHIFT */
unsigned long zone_start_pfn;
/*
mm: introduce new field "managed_pages" to struct zone Currently a zone's present_pages is calcuated as below, which is inaccurate and may cause trouble to memory hotplug. spanned_pages - absent_pages - memmap_pages - dma_reserve. During fixing bugs caused by inaccurate zone->present_pages, we found zone->present_pages has been abused. The field zone->present_pages may have different meanings in different contexts: 1) pages existing in a zone. 2) pages managed by the buddy system. For more discussions about the issue, please refer to: http://lkml.org/lkml/2012/11/5/866 https://patchwork.kernel.org/patch/1346751/ This patchset tries to introduce a new field named "managed_pages" to struct zone, which counts "pages managed by the buddy system". And revert zone->present_pages to count "physical pages existing in a zone", which also keep in consistence with pgdat->node_present_pages. We will set an initial value for zone->managed_pages in function free_area_init_core() and will adjust it later if the initial value is inaccurate. For DMA/normal zones, the initial value is set to: (spanned_pages - absent_pages - memmap_pages - dma_reserve) Later zone->managed_pages will be adjusted to the accurate value when the bootmem allocator frees all free pages to the buddy system in function free_all_bootmem_node() and free_all_bootmem(). The bootmem allocator doesn't touch highmem pages, so highmem zones' managed_pages is set to the accurate value "spanned_pages - absent_pages" in function free_area_init_core() and won't be updated anymore. This patch also adds a new field "managed_pages" to /proc/zoneinfo and sysrq showmem. [akpm@linux-foundation.org: small comment tweaks] Signed-off-by: Jiang Liu <jiang.liu@huawei.com> Cc: Wen Congyang <wency@cn.fujitsu.com> Cc: David Rientjes <rientjes@google.com> Cc: Maciej Rutecki <maciej.rutecki@gmail.com> Tested-by: Chris Clayton <chris2553@googlemail.com> Cc: "Rafael J . Wysocki" <rjw@sisk.pl> Cc: Mel Gorman <mgorman@suse.de> Cc: Minchan Kim <minchan@kernel.org> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Michal Hocko <mhocko@suse.cz> Cc: Jianguo Wu <wujianguo@huawei.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-12-13 04:52:12 +07:00
* spanned_pages is the total pages spanned by the zone, including
* holes, which is calculated as:
* spanned_pages = zone_end_pfn - zone_start_pfn;
*
mm: introduce new field "managed_pages" to struct zone Currently a zone's present_pages is calcuated as below, which is inaccurate and may cause trouble to memory hotplug. spanned_pages - absent_pages - memmap_pages - dma_reserve. During fixing bugs caused by inaccurate zone->present_pages, we found zone->present_pages has been abused. The field zone->present_pages may have different meanings in different contexts: 1) pages existing in a zone. 2) pages managed by the buddy system. For more discussions about the issue, please refer to: http://lkml.org/lkml/2012/11/5/866 https://patchwork.kernel.org/patch/1346751/ This patchset tries to introduce a new field named "managed_pages" to struct zone, which counts "pages managed by the buddy system". And revert zone->present_pages to count "physical pages existing in a zone", which also keep in consistence with pgdat->node_present_pages. We will set an initial value for zone->managed_pages in function free_area_init_core() and will adjust it later if the initial value is inaccurate. For DMA/normal zones, the initial value is set to: (spanned_pages - absent_pages - memmap_pages - dma_reserve) Later zone->managed_pages will be adjusted to the accurate value when the bootmem allocator frees all free pages to the buddy system in function free_all_bootmem_node() and free_all_bootmem(). The bootmem allocator doesn't touch highmem pages, so highmem zones' managed_pages is set to the accurate value "spanned_pages - absent_pages" in function free_area_init_core() and won't be updated anymore. This patch also adds a new field "managed_pages" to /proc/zoneinfo and sysrq showmem. [akpm@linux-foundation.org: small comment tweaks] Signed-off-by: Jiang Liu <jiang.liu@huawei.com> Cc: Wen Congyang <wency@cn.fujitsu.com> Cc: David Rientjes <rientjes@google.com> Cc: Maciej Rutecki <maciej.rutecki@gmail.com> Tested-by: Chris Clayton <chris2553@googlemail.com> Cc: "Rafael J . Wysocki" <rjw@sisk.pl> Cc: Mel Gorman <mgorman@suse.de> Cc: Minchan Kim <minchan@kernel.org> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Michal Hocko <mhocko@suse.cz> Cc: Jianguo Wu <wujianguo@huawei.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-12-13 04:52:12 +07:00
* present_pages is physical pages existing within the zone, which
* is calculated as:
* present_pages = spanned_pages - absent_pages(pages in holes);
mm: introduce new field "managed_pages" to struct zone Currently a zone's present_pages is calcuated as below, which is inaccurate and may cause trouble to memory hotplug. spanned_pages - absent_pages - memmap_pages - dma_reserve. During fixing bugs caused by inaccurate zone->present_pages, we found zone->present_pages has been abused. The field zone->present_pages may have different meanings in different contexts: 1) pages existing in a zone. 2) pages managed by the buddy system. For more discussions about the issue, please refer to: http://lkml.org/lkml/2012/11/5/866 https://patchwork.kernel.org/patch/1346751/ This patchset tries to introduce a new field named "managed_pages" to struct zone, which counts "pages managed by the buddy system". And revert zone->present_pages to count "physical pages existing in a zone", which also keep in consistence with pgdat->node_present_pages. We will set an initial value for zone->managed_pages in function free_area_init_core() and will adjust it later if the initial value is inaccurate. For DMA/normal zones, the initial value is set to: (spanned_pages - absent_pages - memmap_pages - dma_reserve) Later zone->managed_pages will be adjusted to the accurate value when the bootmem allocator frees all free pages to the buddy system in function free_all_bootmem_node() and free_all_bootmem(). The bootmem allocator doesn't touch highmem pages, so highmem zones' managed_pages is set to the accurate value "spanned_pages - absent_pages" in function free_area_init_core() and won't be updated anymore. This patch also adds a new field "managed_pages" to /proc/zoneinfo and sysrq showmem. [akpm@linux-foundation.org: small comment tweaks] Signed-off-by: Jiang Liu <jiang.liu@huawei.com> Cc: Wen Congyang <wency@cn.fujitsu.com> Cc: David Rientjes <rientjes@google.com> Cc: Maciej Rutecki <maciej.rutecki@gmail.com> Tested-by: Chris Clayton <chris2553@googlemail.com> Cc: "Rafael J . Wysocki" <rjw@sisk.pl> Cc: Mel Gorman <mgorman@suse.de> Cc: Minchan Kim <minchan@kernel.org> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Michal Hocko <mhocko@suse.cz> Cc: Jianguo Wu <wujianguo@huawei.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-12-13 04:52:12 +07:00
*
* managed_pages is present pages managed by the buddy system, which
* is calculated as (reserved_pages includes pages allocated by the
* bootmem allocator):
* managed_pages = present_pages - reserved_pages;
*
* So present_pages may be used by memory hotplug or memory power
* management logic to figure out unmanaged pages by checking
* (present_pages - managed_pages). And managed_pages should be used
* by page allocator and vm scanner to calculate all kinds of watermarks
* and thresholds.
*
* Locking rules:
*
* zone_start_pfn and spanned_pages are protected by span_seqlock.
* It is a seqlock because it has to be read outside of zone->lock,
* and it is done in the main allocator path. But, it is written
* quite infrequently.
*
* The span_seq lock is declared along with zone->lock because it is
* frequently read in proximity to zone->lock. It's good to
* give them a chance of being in the same cacheline.
mm: introduce new field "managed_pages" to struct zone Currently a zone's present_pages is calcuated as below, which is inaccurate and may cause trouble to memory hotplug. spanned_pages - absent_pages - memmap_pages - dma_reserve. During fixing bugs caused by inaccurate zone->present_pages, we found zone->present_pages has been abused. The field zone->present_pages may have different meanings in different contexts: 1) pages existing in a zone. 2) pages managed by the buddy system. For more discussions about the issue, please refer to: http://lkml.org/lkml/2012/11/5/866 https://patchwork.kernel.org/patch/1346751/ This patchset tries to introduce a new field named "managed_pages" to struct zone, which counts "pages managed by the buddy system". And revert zone->present_pages to count "physical pages existing in a zone", which also keep in consistence with pgdat->node_present_pages. We will set an initial value for zone->managed_pages in function free_area_init_core() and will adjust it later if the initial value is inaccurate. For DMA/normal zones, the initial value is set to: (spanned_pages - absent_pages - memmap_pages - dma_reserve) Later zone->managed_pages will be adjusted to the accurate value when the bootmem allocator frees all free pages to the buddy system in function free_all_bootmem_node() and free_all_bootmem(). The bootmem allocator doesn't touch highmem pages, so highmem zones' managed_pages is set to the accurate value "spanned_pages - absent_pages" in function free_area_init_core() and won't be updated anymore. This patch also adds a new field "managed_pages" to /proc/zoneinfo and sysrq showmem. [akpm@linux-foundation.org: small comment tweaks] Signed-off-by: Jiang Liu <jiang.liu@huawei.com> Cc: Wen Congyang <wency@cn.fujitsu.com> Cc: David Rientjes <rientjes@google.com> Cc: Maciej Rutecki <maciej.rutecki@gmail.com> Tested-by: Chris Clayton <chris2553@googlemail.com> Cc: "Rafael J . Wysocki" <rjw@sisk.pl> Cc: Mel Gorman <mgorman@suse.de> Cc: Minchan Kim <minchan@kernel.org> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Michal Hocko <mhocko@suse.cz> Cc: Jianguo Wu <wujianguo@huawei.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-12-13 04:52:12 +07:00
*
mm: use a dedicated lock to protect totalram_pages and zone->managed_pages Currently lock_memory_hotplug()/unlock_memory_hotplug() are used to protect totalram_pages and zone->managed_pages. Other than the memory hotplug driver, totalram_pages and zone->managed_pages may also be modified at runtime by other drivers, such as Xen balloon, virtio_balloon etc. For those cases, memory hotplug lock is a little too heavy, so introduce a dedicated lock to protect totalram_pages and zone->managed_pages. Now we have a simplified locking rules totalram_pages and zone->managed_pages as: 1) no locking for read accesses because they are unsigned long. 2) no locking for write accesses at boot time in single-threaded context. 3) serialize write accesses at runtime by acquiring the dedicated managed_page_count_lock. Also adjust zone->managed_pages when freeing reserved pages into the buddy system, to keep totalram_pages and zone->managed_pages in consistence. [akpm@linux-foundation.org: don't export adjust_managed_page_count to modules (for now)] Signed-off-by: Jiang Liu <jiang.liu@huawei.com> Cc: Mel Gorman <mel@csn.ul.ie> Cc: Michel Lespinasse <walken@google.com> Cc: Rik van Riel <riel@redhat.com> Cc: Minchan Kim <minchan@kernel.org> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: "Michael S. Tsirkin" <mst@redhat.com> Cc: <sworddragon2@aol.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Chris Metcalf <cmetcalf@tilera.com> Cc: David Howells <dhowells@redhat.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Jianguo Wu <wujianguo@huawei.com> Cc: Joonsoo Kim <js1304@gmail.com> Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Tang Chen <tangchen@cn.fujitsu.com> Cc: Tejun Heo <tj@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Wen Congyang <wency@cn.fujitsu.com> Cc: Will Deacon <will.deacon@arm.com> Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> Cc: Yinghai Lu <yinghai@kernel.org> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-07-04 05:03:14 +07:00
* Write access to present_pages at runtime should be protected by
mem-hotplug: implement get/put_online_mems kmem_cache_{create,destroy,shrink} need to get a stable value of cpu/node online mask, because they init/destroy/access per-cpu/node kmem_cache parts, which can be allocated or destroyed on cpu/mem hotplug. To protect against cpu hotplug, these functions use {get,put}_online_cpus. However, they do nothing to synchronize with memory hotplug - taking the slab_mutex does not eliminate the possibility of race as described in patch 2. What we need there is something like get_online_cpus, but for memory. We already have lock_memory_hotplug, which serves for the purpose, but it's a bit of a hammer right now, because it's backed by a mutex. As a result, it imposes some limitations to locking order, which are not desirable, and can't be used just like get_online_cpus. That's why in patch 1 I substitute it with get/put_online_mems, which work exactly like get/put_online_cpus except they block not cpu, but memory hotplug. [ v1 can be found at https://lkml.org/lkml/2014/4/6/68. I NAK'ed it by myself, because it used an rw semaphore for get/put_online_mems, making them dead lock prune. ] This patch (of 2): {un}lock_memory_hotplug, which is used to synchronize against memory hotplug, is currently backed by a mutex, which makes it a bit of a hammer - threads that only want to get a stable value of online nodes mask won't be able to proceed concurrently. Also, it imposes some strong locking ordering rules on it, which narrows down the set of its usage scenarios. This patch introduces get/put_online_mems, which are the same as get/put_online_cpus, but for memory hotplug, i.e. executing a code inside a get/put_online_mems section will guarantee a stable value of online nodes, present pages, etc. lock_memory_hotplug()/unlock_memory_hotplug() are removed altogether. Signed-off-by: Vladimir Davydov <vdavydov@parallels.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: Tang Chen <tangchen@cn.fujitsu.com> Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com> Cc: Toshi Kani <toshi.kani@hp.com> Cc: Xishi Qiu <qiuxishi@huawei.com> Cc: Jiang Liu <liuj97@gmail.com> Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: David Rientjes <rientjes@google.com> Cc: Wen Congyang <wency@cn.fujitsu.com> Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> Cc: Lai Jiangshan <laijs@cn.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-06-05 06:07:18 +07:00
* mem_hotplug_begin/end(). Any reader who can't tolerant drift of
* present_pages should get_online_mems() to get a stable value.
mm: use a dedicated lock to protect totalram_pages and zone->managed_pages Currently lock_memory_hotplug()/unlock_memory_hotplug() are used to protect totalram_pages and zone->managed_pages. Other than the memory hotplug driver, totalram_pages and zone->managed_pages may also be modified at runtime by other drivers, such as Xen balloon, virtio_balloon etc. For those cases, memory hotplug lock is a little too heavy, so introduce a dedicated lock to protect totalram_pages and zone->managed_pages. Now we have a simplified locking rules totalram_pages and zone->managed_pages as: 1) no locking for read accesses because they are unsigned long. 2) no locking for write accesses at boot time in single-threaded context. 3) serialize write accesses at runtime by acquiring the dedicated managed_page_count_lock. Also adjust zone->managed_pages when freeing reserved pages into the buddy system, to keep totalram_pages and zone->managed_pages in consistence. [akpm@linux-foundation.org: don't export adjust_managed_page_count to modules (for now)] Signed-off-by: Jiang Liu <jiang.liu@huawei.com> Cc: Mel Gorman <mel@csn.ul.ie> Cc: Michel Lespinasse <walken@google.com> Cc: Rik van Riel <riel@redhat.com> Cc: Minchan Kim <minchan@kernel.org> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: "Michael S. Tsirkin" <mst@redhat.com> Cc: <sworddragon2@aol.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Chris Metcalf <cmetcalf@tilera.com> Cc: David Howells <dhowells@redhat.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Jianguo Wu <wujianguo@huawei.com> Cc: Joonsoo Kim <js1304@gmail.com> Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Tang Chen <tangchen@cn.fujitsu.com> Cc: Tejun Heo <tj@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Wen Congyang <wency@cn.fujitsu.com> Cc: Will Deacon <will.deacon@arm.com> Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> Cc: Yinghai Lu <yinghai@kernel.org> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-07-04 05:03:14 +07:00
*
* Read access to managed_pages should be safe because it's unsigned
* long. Write access to zone->managed_pages and totalram_pages are
* protected by managed_page_count_lock at runtime. Idealy only
* adjust_managed_page_count() should be used instead of directly
* touching zone->managed_pages and totalram_pages.
*/
mm: rearrange zone fields into read-only, page alloc, statistics and page reclaim lines The arrangement of struct zone has changed over time and now it has reached the point where there is some inappropriate sharing going on. On x86-64 for example o The zone->node field is shared with the zone lock and zone->node is accessed frequently from the page allocator due to the fair zone allocation policy. o span_seqlock is almost never used by shares a line with free_area o Some zone statistics share a cache line with the LRU lock so reclaim-intensive and allocator-intensive workloads can bounce the cache line on a stat update This patch rearranges struct zone to put read-only and read-mostly fields together and then splits the page allocator intensive fields, the zone statistics and the page reclaim intensive fields into their own cache lines. Note that the type of lowmem_reserve changes due to the watermark calculations being signed and avoiding a signed/unsigned conversion there. On the test configuration I used the overall size of struct zone shrunk by one cache line. On smaller machines, this is not likely to be noticable. However, on a 4-node NUMA machine running tiobench the system CPU overhead is reduced by this patch. 3.16.0-rc3 3.16.0-rc3 vanillarearrange-v5r9 User 746.94 759.78 System 65336.22 58350.98 Elapsed 27553.52 27282.02 Signed-off-by: Mel Gorman <mgorman@suse.de> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-08-07 06:07:14 +07:00
unsigned long managed_pages;
mm: introduce new field "managed_pages" to struct zone Currently a zone's present_pages is calcuated as below, which is inaccurate and may cause trouble to memory hotplug. spanned_pages - absent_pages - memmap_pages - dma_reserve. During fixing bugs caused by inaccurate zone->present_pages, we found zone->present_pages has been abused. The field zone->present_pages may have different meanings in different contexts: 1) pages existing in a zone. 2) pages managed by the buddy system. For more discussions about the issue, please refer to: http://lkml.org/lkml/2012/11/5/866 https://patchwork.kernel.org/patch/1346751/ This patchset tries to introduce a new field named "managed_pages" to struct zone, which counts "pages managed by the buddy system". And revert zone->present_pages to count "physical pages existing in a zone", which also keep in consistence with pgdat->node_present_pages. We will set an initial value for zone->managed_pages in function free_area_init_core() and will adjust it later if the initial value is inaccurate. For DMA/normal zones, the initial value is set to: (spanned_pages - absent_pages - memmap_pages - dma_reserve) Later zone->managed_pages will be adjusted to the accurate value when the bootmem allocator frees all free pages to the buddy system in function free_all_bootmem_node() and free_all_bootmem(). The bootmem allocator doesn't touch highmem pages, so highmem zones' managed_pages is set to the accurate value "spanned_pages - absent_pages" in function free_area_init_core() and won't be updated anymore. This patch also adds a new field "managed_pages" to /proc/zoneinfo and sysrq showmem. [akpm@linux-foundation.org: small comment tweaks] Signed-off-by: Jiang Liu <jiang.liu@huawei.com> Cc: Wen Congyang <wency@cn.fujitsu.com> Cc: David Rientjes <rientjes@google.com> Cc: Maciej Rutecki <maciej.rutecki@gmail.com> Tested-by: Chris Clayton <chris2553@googlemail.com> Cc: "Rafael J . Wysocki" <rjw@sisk.pl> Cc: Mel Gorman <mgorman@suse.de> Cc: Minchan Kim <minchan@kernel.org> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Michal Hocko <mhocko@suse.cz> Cc: Jianguo Wu <wujianguo@huawei.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-12-13 04:52:12 +07:00
unsigned long spanned_pages;
unsigned long present_pages;
mm: rearrange zone fields into read-only, page alloc, statistics and page reclaim lines The arrangement of struct zone has changed over time and now it has reached the point where there is some inappropriate sharing going on. On x86-64 for example o The zone->node field is shared with the zone lock and zone->node is accessed frequently from the page allocator due to the fair zone allocation policy. o span_seqlock is almost never used by shares a line with free_area o Some zone statistics share a cache line with the LRU lock so reclaim-intensive and allocator-intensive workloads can bounce the cache line on a stat update This patch rearranges struct zone to put read-only and read-mostly fields together and then splits the page allocator intensive fields, the zone statistics and the page reclaim intensive fields into their own cache lines. Note that the type of lowmem_reserve changes due to the watermark calculations being signed and avoiding a signed/unsigned conversion there. On the test configuration I used the overall size of struct zone shrunk by one cache line. On smaller machines, this is not likely to be noticable. However, on a 4-node NUMA machine running tiobench the system CPU overhead is reduced by this patch. 3.16.0-rc3 3.16.0-rc3 vanillarearrange-v5r9 User 746.94 759.78 System 65336.22 58350.98 Elapsed 27553.52 27282.02 Signed-off-by: Mel Gorman <mgorman@suse.de> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-08-07 06:07:14 +07:00
const char *name;
mm: get rid of unnecessary pageblock scanning in setup_zone_migrate_reserve Yasuaki Ishimatsu reported memory hot-add spent more than 5 _hours_ on 9TB memory machine since onlining memory sections is too slow. And we found out setup_zone_migrate_reserve spent >90% of the time. The problem is, setup_zone_migrate_reserve scans all pageblocks unconditionally, but it is only necessary if the number of reserved block was reduced (i.e. memory hot remove). Moreover, maximum MIGRATE_RESERVE per zone is currently 2. It means that the number of reserved pageblocks is almost always unchanged. This patch adds zone->nr_migrate_reserve_block to maintain the number of MIGRATE_RESERVE pageblocks and it reduces the overhead of setup_zone_migrate_reserve dramatically. The following table shows time of onlining a memory section. Amount of memory | 128GB | 192GB | 256GB| --------------------------------------------- linux-3.12 | 23.9 | 31.4 | 44.5 | This patch | 8.3 | 8.3 | 8.6 | Mel's proposal patch | 10.9 | 19.2 | 31.3 | --------------------------------------------- (millisecond) 128GB : 4 nodes and each node has 32GB of memory 192GB : 6 nodes and each node has 32GB of memory 256GB : 8 nodes and each node has 32GB of memory (*1) Mel proposed his idea by the following threads. https://lkml.org/lkml/2013/10/30/272 [akpm@linux-foundation.org: tweak comment] Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> Reported-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> Tested-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> Cc: Mel Gorman <mgorman@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-01-22 06:49:06 +07:00
/*
* Number of MIGRATE_RESERVE page block. To maintain for just
mm: get rid of unnecessary pageblock scanning in setup_zone_migrate_reserve Yasuaki Ishimatsu reported memory hot-add spent more than 5 _hours_ on 9TB memory machine since onlining memory sections is too slow. And we found out setup_zone_migrate_reserve spent >90% of the time. The problem is, setup_zone_migrate_reserve scans all pageblocks unconditionally, but it is only necessary if the number of reserved block was reduced (i.e. memory hot remove). Moreover, maximum MIGRATE_RESERVE per zone is currently 2. It means that the number of reserved pageblocks is almost always unchanged. This patch adds zone->nr_migrate_reserve_block to maintain the number of MIGRATE_RESERVE pageblocks and it reduces the overhead of setup_zone_migrate_reserve dramatically. The following table shows time of onlining a memory section. Amount of memory | 128GB | 192GB | 256GB| --------------------------------------------- linux-3.12 | 23.9 | 31.4 | 44.5 | This patch | 8.3 | 8.3 | 8.6 | Mel's proposal patch | 10.9 | 19.2 | 31.3 | --------------------------------------------- (millisecond) 128GB : 4 nodes and each node has 32GB of memory 192GB : 6 nodes and each node has 32GB of memory 256GB : 8 nodes and each node has 32GB of memory (*1) Mel proposed his idea by the following threads. https://lkml.org/lkml/2013/10/30/272 [akpm@linux-foundation.org: tweak comment] Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> Reported-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> Tested-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> Cc: Mel Gorman <mgorman@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-01-22 06:49:06 +07:00
* optimization. Protected by zone->lock.
*/
int nr_migrate_reserve_block;
mm/page_alloc: fix incorrect isolation behavior by rechecking migratetype Before describing bugs itself, I first explain definition of freepage. 1. pages on buddy list are counted as freepage. 2. pages on isolate migratetype buddy list are *not* counted as freepage. 3. pages on cma buddy list are counted as CMA freepage, too. Now, I describe problems and related patch. Patch 1: There is race conditions on getting pageblock migratetype that it results in misplacement of freepages on buddy list, incorrect freepage count and un-availability of freepage. Patch 2: Freepages on pcp list could have stale cached information to determine migratetype of buddy list to go. This causes misplacement of freepages on buddy list and incorrect freepage count. Patch 4: Merging between freepages on different migratetype of pageblocks will cause freepages accouting problem. This patch fixes it. Without patchset [3], above problem doesn't happens on my CMA allocation test, because CMA reserved pages aren't used at all. So there is no chance for above race. With patchset [3], I did simple CMA allocation test and get below result: - Virtual machine, 4 cpus, 1024 MB memory, 256 MB CMA reservation - run kernel build (make -j16) on background - 30 times CMA allocation(8MB * 30 = 240MB) attempts in 5 sec interval - Result: more than 5000 freepage count are missed With patchset [3] and this patchset, I found that no freepage count are missed so that I conclude that problems are solved. On my simple memory offlining test, these problems also occur on that environment, too. This patch (of 4): There are two paths to reach core free function of buddy allocator, __free_one_page(), one is free_one_page()->__free_one_page() and the other is free_hot_cold_page()->free_pcppages_bulk()->__free_one_page(). Each paths has race condition causing serious problems. At first, this patch is focused on first type of freepath. And then, following patch will solve the problem in second type of freepath. In the first type of freepath, we got migratetype of freeing page without holding the zone lock, so it could be racy. There are two cases of this race. 1. pages are added to isolate buddy list after restoring orignal migratetype CPU1 CPU2 get migratetype => return MIGRATE_ISOLATE call free_one_page() with MIGRATE_ISOLATE grab the zone lock unisolate pageblock release the zone lock grab the zone lock call __free_one_page() with MIGRATE_ISOLATE freepage go into isolate buddy list, although pageblock is already unisolated This may cause two problems. One is that we can't use this page anymore until next isolation attempt of this pageblock, because freepage is on isolate buddy list. The other is that freepage accouting could be wrong due to merging between different buddy list. Freepages on isolate buddy list aren't counted as freepage, but ones on normal buddy list are counted as freepage. If merge happens, buddy freepage on normal buddy list is inevitably moved to isolate buddy list without any consideration of freepage accouting so it could be incorrect. 2. pages are added to normal buddy list while pageblock is isolated. It is similar with above case. This also may cause two problems. One is that we can't keep these freepages from being allocated. Although this pageblock is isolated, freepage would be added to normal buddy list so that it could be allocated without any restriction. And the other problem is same as case 1, that it, incorrect freepage accouting. This race condition would be prevented by checking migratetype again with holding the zone lock. Because it is somewhat heavy operation and it isn't needed in common case, we want to avoid rechecking as much as possible. So this patch introduce new variable, nr_isolate_pageblock in struct zone to check if there is isolated pageblock. With this, we can avoid to re-check migratetype in common case and do it only if there is isolated pageblock or migratetype is MIGRATE_ISOLATE. This solve above mentioned problems. Changes from v3: Add one more check in free_one_page() that checks whether migratetype is MIGRATE_ISOLATE or not. Without this, abovementioned case 1 could happens. Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Acked-by: Minchan Kim <minchan@kernel.org> Acked-by: Michal Nazarewicz <mina86@mina86.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: "Kirill A. Shutemov" <kirill@shutemov.name> Cc: Mel Gorman <mgorman@suse.de> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com> Cc: Tang Chen <tangchen@cn.fujitsu.com> Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Cc: Wen Congyang <wency@cn.fujitsu.com> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Laura Abbott <lauraa@codeaurora.org> Cc: Heesub Shin <heesub.shin@samsung.com> Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com> Cc: Ritesh Harjani <ritesh.list@gmail.com> Cc: Gioh Kim <gioh.kim@lge.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-11-14 06:19:11 +07:00
#ifdef CONFIG_MEMORY_ISOLATION
/*
* Number of isolated pageblock. It is used to solve incorrect
* freepage counting problem due to racy retrieving migratetype
* of pageblock. Protected by zone->lock.
*/
unsigned long nr_isolate_pageblock;
#endif
mm: rearrange zone fields into read-only, page alloc, statistics and page reclaim lines The arrangement of struct zone has changed over time and now it has reached the point where there is some inappropriate sharing going on. On x86-64 for example o The zone->node field is shared with the zone lock and zone->node is accessed frequently from the page allocator due to the fair zone allocation policy. o span_seqlock is almost never used by shares a line with free_area o Some zone statistics share a cache line with the LRU lock so reclaim-intensive and allocator-intensive workloads can bounce the cache line on a stat update This patch rearranges struct zone to put read-only and read-mostly fields together and then splits the page allocator intensive fields, the zone statistics and the page reclaim intensive fields into their own cache lines. Note that the type of lowmem_reserve changes due to the watermark calculations being signed and avoiding a signed/unsigned conversion there. On the test configuration I used the overall size of struct zone shrunk by one cache line. On smaller machines, this is not likely to be noticable. However, on a 4-node NUMA machine running tiobench the system CPU overhead is reduced by this patch. 3.16.0-rc3 3.16.0-rc3 vanillarearrange-v5r9 User 746.94 759.78 System 65336.22 58350.98 Elapsed 27553.52 27282.02 Signed-off-by: Mel Gorman <mgorman@suse.de> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-08-07 06:07:14 +07:00
#ifdef CONFIG_MEMORY_HOTPLUG
/* see spanned/present_pages for more description */
seqlock_t span_seqlock;
#endif
/*
mm: rearrange zone fields into read-only, page alloc, statistics and page reclaim lines The arrangement of struct zone has changed over time and now it has reached the point where there is some inappropriate sharing going on. On x86-64 for example o The zone->node field is shared with the zone lock and zone->node is accessed frequently from the page allocator due to the fair zone allocation policy. o span_seqlock is almost never used by shares a line with free_area o Some zone statistics share a cache line with the LRU lock so reclaim-intensive and allocator-intensive workloads can bounce the cache line on a stat update This patch rearranges struct zone to put read-only and read-mostly fields together and then splits the page allocator intensive fields, the zone statistics and the page reclaim intensive fields into their own cache lines. Note that the type of lowmem_reserve changes due to the watermark calculations being signed and avoiding a signed/unsigned conversion there. On the test configuration I used the overall size of struct zone shrunk by one cache line. On smaller machines, this is not likely to be noticable. However, on a 4-node NUMA machine running tiobench the system CPU overhead is reduced by this patch. 3.16.0-rc3 3.16.0-rc3 vanillarearrange-v5r9 User 746.94 759.78 System 65336.22 58350.98 Elapsed 27553.52 27282.02 Signed-off-by: Mel Gorman <mgorman@suse.de> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-08-07 06:07:14 +07:00
* wait_table -- the array holding the hash table
* wait_table_hash_nr_entries -- the size of the hash table array
* wait_table_bits -- wait_table_size == (1 << wait_table_bits)
*
* The purpose of all these is to keep track of the people
* waiting for a page to become available and make them
* runnable again when possible. The trouble is that this
* consumes a lot of space, especially when so few things
* wait on pages at a given time. So instead of using
* per-page waitqueues, we use a waitqueue hash table.
*
* The bucket discipline is to sleep on the same queue when
* colliding and wake all in that wait queue when removing.
* When something wakes, it must check to be sure its page is
* truly available, a la thundering herd. The cost of a
* collision is great, but given the expected load of the
* table, they should be so rare as to be outweighed by the
* benefits from the saved space.
*
* __wait_on_page_locked() and unlock_page() in mm/filemap.c, are the
* primary users of these fields, and in mm/page_alloc.c
* free_area_init_core() performs the initialization of them.
*/
mm: rearrange zone fields into read-only, page alloc, statistics and page reclaim lines The arrangement of struct zone has changed over time and now it has reached the point where there is some inappropriate sharing going on. On x86-64 for example o The zone->node field is shared with the zone lock and zone->node is accessed frequently from the page allocator due to the fair zone allocation policy. o span_seqlock is almost never used by shares a line with free_area o Some zone statistics share a cache line with the LRU lock so reclaim-intensive and allocator-intensive workloads can bounce the cache line on a stat update This patch rearranges struct zone to put read-only and read-mostly fields together and then splits the page allocator intensive fields, the zone statistics and the page reclaim intensive fields into their own cache lines. Note that the type of lowmem_reserve changes due to the watermark calculations being signed and avoiding a signed/unsigned conversion there. On the test configuration I used the overall size of struct zone shrunk by one cache line. On smaller machines, this is not likely to be noticable. However, on a 4-node NUMA machine running tiobench the system CPU overhead is reduced by this patch. 3.16.0-rc3 3.16.0-rc3 vanillarearrange-v5r9 User 746.94 759.78 System 65336.22 58350.98 Elapsed 27553.52 27282.02 Signed-off-by: Mel Gorman <mgorman@suse.de> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-08-07 06:07:14 +07:00
wait_queue_head_t *wait_table;
unsigned long wait_table_hash_nr_entries;
unsigned long wait_table_bits;
ZONE_PADDING(_pad1_)
/* free areas of different sizes */
struct free_area free_area[MAX_ORDER];
/* zone flags, see below */
unsigned long flags;
mm: move zone lock to a different cache line than order-0 free page lists Huang Ying reported the following problem due to commit 3484b2de9499 ("mm: rearrange zone fields into read-only, page alloc, statistics and page reclaim lines") from the Intel performance tests 24b7e5819ad5cbef 3484b2de9499df23c4604a513b ---------------- -------------------------- %stddev %change %stddev \ | \ 152288 \261 0% -46.2% 81911 \261 0% aim7.jobs-per-min 237 \261 0% +85.6% 440 \261 0% aim7.time.elapsed_time 237 \261 0% +85.6% 440 \261 0% aim7.time.elapsed_time.max 25026 \261 0% +70.7% 42712 \261 0% aim7.time.system_time 2186645 \261 5% +32.0% 2885949 \261 4% aim7.time.voluntary_context_switches 4576561 \261 1% +24.9% 5715773 \261 0% aim7.time.involuntary_context_switches The problem is specific to very large machines under stress. It was not reproducible with the machines I had used to justify the original patch because large numbers of CPUs are required. When pressure is high enough, the cache line is bouncing between CPUs trying to acquire the lock and the holder of the lock adjusting free lists. The intention was that the acquirer of the lock would automatically have the cache line holding the free lists but according to Huang, this is not a universal win. One possibility is to move the zone lock to its own cache line but it increases the size of the zone. This patch moves the lock to the other end of the free lists where they do not contend under high pressure. It does mean the page allocator paths now require more cache lines but Huang reports that it restores performance to previous levels on large machines %stddev %change %stddev \ | \ 84568 \261 1% +94.3% 164280 \261 1% aim7.jobs-per-min 2881944 \261 2% -35.1% 1870386 \261 8% aim7.time.voluntary_context_switches 681 \261 1% -3.4% 658 \261 0% aim7.time.user_time 5538139 \261 0% -12.1% 4867884 \261 0% aim7.time.involuntary_context_switches 44174 \261 1% -46.0% 23848 \261 1% aim7.time.system_time 426 \261 1% -48.4% 219 \261 1% aim7.time.elapsed_time 426 \261 1% -48.4% 219 \261 1% aim7.time.elapsed_time.max 468 \261 1% -43.1% 266 \261 2% uptime.boot Signed-off-by: Mel Gorman <mgorman@suse.de> Reported-by: Huang Ying <ying.huang@intel.com> Tested-by: Huang Ying <ying.huang@intel.com> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-04-08 04:26:41 +07:00
/* Write-intensive fields used from the page allocator */
spinlock_t lock;
mm: rearrange zone fields into read-only, page alloc, statistics and page reclaim lines The arrangement of struct zone has changed over time and now it has reached the point where there is some inappropriate sharing going on. On x86-64 for example o The zone->node field is shared with the zone lock and zone->node is accessed frequently from the page allocator due to the fair zone allocation policy. o span_seqlock is almost never used by shares a line with free_area o Some zone statistics share a cache line with the LRU lock so reclaim-intensive and allocator-intensive workloads can bounce the cache line on a stat update This patch rearranges struct zone to put read-only and read-mostly fields together and then splits the page allocator intensive fields, the zone statistics and the page reclaim intensive fields into their own cache lines. Note that the type of lowmem_reserve changes due to the watermark calculations being signed and avoiding a signed/unsigned conversion there. On the test configuration I used the overall size of struct zone shrunk by one cache line. On smaller machines, this is not likely to be noticable. However, on a 4-node NUMA machine running tiobench the system CPU overhead is reduced by this patch. 3.16.0-rc3 3.16.0-rc3 vanillarearrange-v5r9 User 746.94 759.78 System 65336.22 58350.98 Elapsed 27553.52 27282.02 Signed-off-by: Mel Gorman <mgorman@suse.de> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-08-07 06:07:14 +07:00
ZONE_PADDING(_pad2_)
/* Write-intensive fields used by page reclaim */
/* Fields commonly accessed by the page reclaim scanner */
spinlock_t lru_lock;
struct lruvec lruvec;
/* Evictions & activations on the inactive file list */
atomic_long_t inactive_age;
/*
* When free pages are below this point, additional steps are taken
* when reading the number of free pages to avoid per-cpu counter
* drift allowing watermarks to be breached
*/
unsigned long percpu_drift_mark;
#if defined CONFIG_COMPACTION || defined CONFIG_CMA
/* pfn where compaction free scanner should start */
unsigned long compact_cached_free_pfn;
/* pfn where async and sync compaction migration scanner should start */
unsigned long compact_cached_migrate_pfn[2];
#endif
#ifdef CONFIG_COMPACTION
/*
* On compaction failure, 1<<compact_defer_shift compactions
* are skipped before trying again. The number attempted since
* last failure is tracked with compact_considered.
*/
unsigned int compact_considered;
unsigned int compact_defer_shift;
int compact_order_failed;
#endif
#if defined CONFIG_COMPACTION || defined CONFIG_CMA
/* Set to true when the PG_migrate_skip bits should be cleared */
bool compact_blockskip_flush;
#endif
ZONE_PADDING(_pad3_)
/* Zone statistics */
atomic_long_t vm_stat[NR_VM_ZONE_STAT_ITEMS];
} ____cacheline_internodealigned_in_smp;
enum zone_flags {
ZONE_RECLAIM_LOCKED, /* prevents concurrent reclaim */
ZONE_OOM_LOCKED, /* zone is in OOM killer zonelist */
ZONE_CONGESTED, /* zone has many dirty pages backed by
* a congested BDI
*/
ZONE_DIRTY, /* reclaim scanning has recently found
* many dirty file pages at the tail
* of the LRU.
*/
mm: vmscan: block kswapd if it is encountering pages under writeback Historically, kswapd used to congestion_wait() at higher priorities if it was not making forward progress. This made no sense as the failure to make progress could be completely independent of IO. It was later replaced by wait_iff_congested() and removed entirely by commit 258401a6 (mm: don't wait on congested zones in balance_pgdat()) as it was duplicating logic in shrink_inactive_list(). This is problematic. If kswapd encounters many pages under writeback and it continues to scan until it reaches the high watermark then it will quickly skip over the pages under writeback and reclaim clean young pages or push applications out to swap. The use of wait_iff_congested() is not suited to kswapd as it will only stall if the underlying BDI is really congested or a direct reclaimer was unable to write to the underlying BDI. kswapd bypasses the BDI congestion as it sets PF_SWAPWRITE but even if this was taken into account then it would cause direct reclaimers to stall on writeback which is not desirable. This patch sets a ZONE_WRITEBACK flag if direct reclaim or kswapd is encountering too many pages under writeback. If this flag is set and kswapd encounters a PageReclaim page under writeback then it'll assume that the LRU lists are being recycled too quickly before IO can complete and block waiting for some IO to complete. Signed-off-by: Mel Gorman <mgorman@suse.de> Reviewed-by: Michal Hocko <mhocko@suse.cz> Acked-by: Rik van Riel <riel@redhat.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Jiri Slaby <jslaby@suse.cz> Cc: Valdis Kletnieks <Valdis.Kletnieks@vt.edu> Tested-by: Zlatko Calusic <zcalusic@bitsync.net> Cc: dormando <dormando@rydia.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-07-04 05:01:51 +07:00
ZONE_WRITEBACK, /* reclaim scanning has recently found
* many pages under writeback
*/
ZONE_FAIR_DEPLETED, /* fair zone policy batch depleted */
};
mm: zone_end_pfn is too small Booting with 32 TBytes memory hits BUG at mm/page_alloc.c:552! (output below). The key hint is "page 4294967296 outside zone". 4294967296 = 0x100000000 (bit 32 is set). The problem is in include/linux/mmzone.h: 530 static inline unsigned zone_end_pfn(const struct zone *zone) 531 { 532 return zone->zone_start_pfn + zone->spanned_pages; 533 } zone_end_pfn is "unsigned" (32 bits). Changing it to "unsigned long" (64 bits) fixes the problem. zone_end_pfn() was added recently in commit 108bcc96ef70 ("mm: add & use zone_end_pfn() and zone_spans_pfn()") Output from the failure. No AGP bridge found page 4294967296 outside zone [ 4294967296 - 4327469056 ] ------------[ cut here ]------------ kernel BUG at mm/page_alloc.c:552! invalid opcode: 0000 [#1] SMP Modules linked in: CPU 0 Pid: 0, comm: swapper Not tainted 3.9.0-rc2.dtp+ #10 RIP: free_one_page+0x382/0x430 Process swapper (pid: 0, threadinfo ffffffff81942000, task ffffffff81955420) Call Trace: __free_pages_ok+0x96/0xb0 __free_pages+0x25/0x50 __free_pages_bootmem+0x8a/0x8c __free_memory_core+0xea/0x131 free_low_memory_core_early+0x4a/0x98 free_all_bootmem+0x45/0x47 mem_init+0x7b/0x14c start_kernel+0x216/0x433 x86_64_start_reservations+0x2a/0x2c x86_64_start_kernel+0x144/0x153 Code: 89 f1 ba 01 00 00 00 31 f6 d3 e2 4c 89 ef e8 66 a4 01 00 e9 2c fe ff ff 0f 0b eb fe 0f 0b 66 66 2e 0f 1f 84 00 00 00 00 00 eb f3 <0f> 0b eb fe 0f 0b 0f 1f 84 00 00 00 00 00 eb f6 0f 0b eb fe 49 Signed-off-by: Russ Anderson <rja@sgi.com> Reported-by: George Beshers <gbeshers@sgi.com> Acked-by: Hedi Berriche <hedi@sgi.com> Cc: Cody P Schafer <cody@linux.vnet.ibm.com> Cc: Michal Hocko <mhocko@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-03-23 05:04:43 +07:00
static inline unsigned long zone_end_pfn(const struct zone *zone)
{
return zone->zone_start_pfn + zone->spanned_pages;
}
static inline bool zone_spans_pfn(const struct zone *zone, unsigned long pfn)
{
return zone->zone_start_pfn <= pfn && pfn < zone_end_pfn(zone);
}
static inline bool zone_is_initialized(struct zone *zone)
{
return !!zone->wait_table;
}
static inline bool zone_is_empty(struct zone *zone)
{
return zone->spanned_pages == 0;
}
/*
* The "priority" of VM scanning is how much of the queues we will scan in one
* go. A value of 12 for DEF_PRIORITY implies that we will scan 1/4096th of the
* queues ("queue_length >> 12") during an aging round.
*/
#define DEF_PRIORITY 12
[PATCH] memory page_alloc zonelist caching speedup Optimize the critical zonelist scanning for free pages in the kernel memory allocator by caching the zones that were found to be full recently, and skipping them. Remembers the zones in a zonelist that were short of free memory in the last second. And it stashes a zone-to-node table in the zonelist struct, to optimize that conversion (minimize its cache footprint.) Recent changes: This differs in a significant way from a similar patch that I posted a week ago. Now, instead of having a nodemask_t of recently full nodes, I have a bitmask of recently full zones. This solves a problem that last weeks patch had, which on systems with multiple zones per node (such as DMA zone) would take seeing any of these zones full as meaning that all zones on that node were full. Also I changed names - from "zonelist faster" to "zonelist cache", as that seemed to better convey what we're doing here - caching some of the key zonelist state (for faster access.) See below for some performance benchmark results. After all that discussion with David on why I didn't need them, I went and got some ;). I wanted to verify that I had not hurt the normal case of memory allocation noticeably. At least for my one little microbenchmark, I found (1) the normal case wasn't affected, and (2) workloads that forced scanning across multiple nodes for memory improved up to 10% fewer System CPU cycles and lower elapsed clock time ('sys' and 'real'). Good. See details, below. I didn't have the logic in get_page_from_freelist() for various full nodes and zone reclaim failures correct. That should be fixed up now - notice the new goto labels zonelist_scan, this_zone_full, and try_next_zone, in get_page_from_freelist(). There are two reasons I persued this alternative, over some earlier proposals that would have focused on optimizing the fake numa emulation case by caching the last useful zone: 1) Contrary to what I said before, we (SGI, on large ia64 sn2 systems) have seen real customer loads where the cost to scan the zonelist was a problem, due to many nodes being full of memory before we got to a node we could use. Or at least, I think we have. This was related to me by another engineer, based on experiences from some time past. So this is not guaranteed. Most likely, though. The following approach should help such real numa systems just as much as it helps fake numa systems, or any combination thereof. 2) The effort to distinguish fake from real numa, using node_distance, so that we could cache a fake numa node and optimize choosing it over equivalent distance fake nodes, while continuing to properly scan all real nodes in distance order, was going to require a nasty blob of zonelist and node distance munging. The following approach has no new dependency on node distances or zone sorting. See comment in the patch below for a description of what it actually does. Technical details of note (or controversy): - See the use of "zlc_active" and "did_zlc_setup" below, to delay adding any work for this new mechanism until we've looked at the first zone in zonelist. I figured the odds of the first zone having the memory we needed were high enough that we should just look there, first, then get fancy only if we need to keep looking. - Some odd hackery was needed to add items to struct zonelist, while not tripping up the custom zonelists built by the mm/mempolicy.c code for MPOL_BIND. My usual wordy comments below explain this. Search for "MPOL_BIND". - Some per-node data in the struct zonelist is now modified frequently, with no locking. Multiple CPU cores on a node could hit and mangle this data. The theory is that this is just performance hint data, and the memory allocator will work just fine despite any such mangling. The fields at risk are the struct 'zonelist_cache' fields 'fullzones' (a bitmask) and 'last_full_zap' (unsigned long jiffies). It should all be self correcting after at most a one second delay. - This still does a linear scan of the same lengths as before. All I've optimized is making the scan faster, not algorithmically shorter. It is now able to scan a compact array of 'unsigned short' in the case of many full nodes, so one cache line should cover quite a few nodes, rather than each node hitting another one or two new and distinct cache lines. - If both Andi and Nick don't find this too complicated, I will be (pleasantly) flabbergasted. - I removed the comment claiming we only use one cachline's worth of zonelist. We seem, at least in the fake numa case, to have put the lie to that claim. - I pay no attention to the various watermarks and such in this performance hint. A node could be marked full for one watermark, and then skipped over when searching for a page using a different watermark. I think that's actually quite ok, as it will tend to slightly increase the spreading of memory over other nodes, away from a memory stressed node. =============== Performance - some benchmark results and analysis: This benchmark runs a memory hog program that uses multiple threads to touch alot of memory as quickly as it can. Multiple runs were made, touching 12, 38, 64 or 90 GBytes out of the total 96 GBytes on the system, and using 1, 19, 37, or 55 threads (on a 56 CPU system.) System, user and real (elapsed) timings were recorded for each run, shown in units of seconds, in the table below. Two kernels were tested - 2.6.18-mm3 and the same kernel with this zonelist caching patch added. The table also shows the percentage improvement the zonelist caching sys time is over (lower than) the stock *-mm kernel. number 2.6.18-mm3 zonelist-cache delta (< 0 good) percent GBs N ------------ -------------- ---------------- systime mem threads sys user real sys user real sys user real better 12 1 153 24 177 151 24 176 -2 0 -1 1% 12 19 99 22 8 99 22 8 0 0 0 0% 12 37 111 25 6 112 25 6 1 0 0 -0% 12 55 115 25 5 110 23 5 -5 -2 0 4% 38 1 502 74 576 497 73 570 -5 -1 -6 0% 38 19 426 78 48 373 76 39 -53 -2 -9 12% 38 37 544 83 36 547 82 36 3 -1 0 -0% 38 55 501 77 23 511 80 24 10 3 1 -1% 64 1 917 125 1042 890 124 1014 -27 -1 -28 2% 64 19 1118 138 119 965 141 103 -153 3 -16 13% 64 37 1202 151 94 1136 150 81 -66 -1 -13 5% 64 55 1118 141 61 1072 140 58 -46 -1 -3 4% 90 1 1342 177 1519 1275 174 1450 -67 -3 -69 4% 90 19 2392 199 192 2116 189 176 -276 -10 -16 11% 90 37 3313 238 175 2972 225 145 -341 -13 -30 10% 90 55 1948 210 104 1843 213 100 -105 3 -4 5% Notes: 1) This test ran a memory hog program that started a specified number N of threads, and had each thread allocate and touch 1/N'th of the total memory to be used in the test run in a single loop, writing a constant word to memory, one store every 4096 bytes. Watching this test during some earlier trial runs, I would see each of these threads sit down on one CPU and stay there, for the remainder of the pass, a different CPU for each thread. 2) The 'real' column is not comparable to the 'sys' or 'user' columns. The 'real' column is seconds wall clock time elapsed, from beginning to end of that test pass. The 'sys' and 'user' columns are total CPU seconds spent on that test pass. For a 19 thread test run, for example, the sum of 'sys' and 'user' could be up to 19 times the number of 'real' elapsed wall clock seconds. 3) Tests were run on a fresh, single-user boot, to minimize the amount of memory already in use at the start of the test, and to minimize the amount of background activity that might interfere. 4) Tests were done on a 56 CPU, 28 Node system with 96 GBytes of RAM. 5) Notice that the 'real' time gets large for the single thread runs, even though the measured 'sys' and 'user' times are modest. I'm not sure what that means - probably something to do with it being slow for one thread to be accessing memory along ways away. Perhaps the fake numa system, running ostensibly the same workload, would not show this substantial degradation of 'real' time for one thread on many nodes -- lets hope not. 6) The high thread count passes (one thread per CPU - on 55 of 56 CPUs) ran quite efficiently, as one might expect. Each pair of threads needed to allocate and touch the memory on the node the two threads shared, a pleasantly parallizable workload. 7) The intermediate thread count passes, when asking for alot of memory forcing them to go to a few neighboring nodes, improved the most with this zonelist caching patch. Conclusions: * This zonelist cache patch probably makes little difference one way or the other for most workloads on real numa hardware, if those workloads avoid heavy off node allocations. * For memory intensive workloads requiring substantial off-node allocations on real numa hardware, this patch improves both kernel and elapsed timings up to ten per-cent. * For fake numa systems, I'm optimistic, but will have to leave that up to Rohit Seth to actually test (once I get him a 2.6.18 backport.) Signed-off-by: Paul Jackson <pj@sgi.com> Cc: Rohit Seth <rohitseth@google.com> Cc: Christoph Lameter <clameter@engr.sgi.com> Cc: David Rientjes <rientjes@cs.washington.edu> Cc: Paul Menage <menage@google.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-07 11:31:48 +07:00
/* Maximum number of zones on a zonelist */
#define MAX_ZONES_PER_ZONELIST (MAX_NUMNODES * MAX_NR_ZONES)
#ifdef CONFIG_NUMA
/*
* The NUMA zonelists are doubled because we need zonelists that restrict the
* allocations to a single node for __GFP_THISNODE.
*
* [0] : Zonelist with fallback
* [1] : No fallback (__GFP_THISNODE)
*/
#define MAX_ZONELISTS 2
[PATCH] memory page_alloc zonelist caching speedup Optimize the critical zonelist scanning for free pages in the kernel memory allocator by caching the zones that were found to be full recently, and skipping them. Remembers the zones in a zonelist that were short of free memory in the last second. And it stashes a zone-to-node table in the zonelist struct, to optimize that conversion (minimize its cache footprint.) Recent changes: This differs in a significant way from a similar patch that I posted a week ago. Now, instead of having a nodemask_t of recently full nodes, I have a bitmask of recently full zones. This solves a problem that last weeks patch had, which on systems with multiple zones per node (such as DMA zone) would take seeing any of these zones full as meaning that all zones on that node were full. Also I changed names - from "zonelist faster" to "zonelist cache", as that seemed to better convey what we're doing here - caching some of the key zonelist state (for faster access.) See below for some performance benchmark results. After all that discussion with David on why I didn't need them, I went and got some ;). I wanted to verify that I had not hurt the normal case of memory allocation noticeably. At least for my one little microbenchmark, I found (1) the normal case wasn't affected, and (2) workloads that forced scanning across multiple nodes for memory improved up to 10% fewer System CPU cycles and lower elapsed clock time ('sys' and 'real'). Good. See details, below. I didn't have the logic in get_page_from_freelist() for various full nodes and zone reclaim failures correct. That should be fixed up now - notice the new goto labels zonelist_scan, this_zone_full, and try_next_zone, in get_page_from_freelist(). There are two reasons I persued this alternative, over some earlier proposals that would have focused on optimizing the fake numa emulation case by caching the last useful zone: 1) Contrary to what I said before, we (SGI, on large ia64 sn2 systems) have seen real customer loads where the cost to scan the zonelist was a problem, due to many nodes being full of memory before we got to a node we could use. Or at least, I think we have. This was related to me by another engineer, based on experiences from some time past. So this is not guaranteed. Most likely, though. The following approach should help such real numa systems just as much as it helps fake numa systems, or any combination thereof. 2) The effort to distinguish fake from real numa, using node_distance, so that we could cache a fake numa node and optimize choosing it over equivalent distance fake nodes, while continuing to properly scan all real nodes in distance order, was going to require a nasty blob of zonelist and node distance munging. The following approach has no new dependency on node distances or zone sorting. See comment in the patch below for a description of what it actually does. Technical details of note (or controversy): - See the use of "zlc_active" and "did_zlc_setup" below, to delay adding any work for this new mechanism until we've looked at the first zone in zonelist. I figured the odds of the first zone having the memory we needed were high enough that we should just look there, first, then get fancy only if we need to keep looking. - Some odd hackery was needed to add items to struct zonelist, while not tripping up the custom zonelists built by the mm/mempolicy.c code for MPOL_BIND. My usual wordy comments below explain this. Search for "MPOL_BIND". - Some per-node data in the struct zonelist is now modified frequently, with no locking. Multiple CPU cores on a node could hit and mangle this data. The theory is that this is just performance hint data, and the memory allocator will work just fine despite any such mangling. The fields at risk are the struct 'zonelist_cache' fields 'fullzones' (a bitmask) and 'last_full_zap' (unsigned long jiffies). It should all be self correcting after at most a one second delay. - This still does a linear scan of the same lengths as before. All I've optimized is making the scan faster, not algorithmically shorter. It is now able to scan a compact array of 'unsigned short' in the case of many full nodes, so one cache line should cover quite a few nodes, rather than each node hitting another one or two new and distinct cache lines. - If both Andi and Nick don't find this too complicated, I will be (pleasantly) flabbergasted. - I removed the comment claiming we only use one cachline's worth of zonelist. We seem, at least in the fake numa case, to have put the lie to that claim. - I pay no attention to the various watermarks and such in this performance hint. A node could be marked full for one watermark, and then skipped over when searching for a page using a different watermark. I think that's actually quite ok, as it will tend to slightly increase the spreading of memory over other nodes, away from a memory stressed node. =============== Performance - some benchmark results and analysis: This benchmark runs a memory hog program that uses multiple threads to touch alot of memory as quickly as it can. Multiple runs were made, touching 12, 38, 64 or 90 GBytes out of the total 96 GBytes on the system, and using 1, 19, 37, or 55 threads (on a 56 CPU system.) System, user and real (elapsed) timings were recorded for each run, shown in units of seconds, in the table below. Two kernels were tested - 2.6.18-mm3 and the same kernel with this zonelist caching patch added. The table also shows the percentage improvement the zonelist caching sys time is over (lower than) the stock *-mm kernel. number 2.6.18-mm3 zonelist-cache delta (< 0 good) percent GBs N ------------ -------------- ---------------- systime mem threads sys user real sys user real sys user real better 12 1 153 24 177 151 24 176 -2 0 -1 1% 12 19 99 22 8 99 22 8 0 0 0 0% 12 37 111 25 6 112 25 6 1 0 0 -0% 12 55 115 25 5 110 23 5 -5 -2 0 4% 38 1 502 74 576 497 73 570 -5 -1 -6 0% 38 19 426 78 48 373 76 39 -53 -2 -9 12% 38 37 544 83 36 547 82 36 3 -1 0 -0% 38 55 501 77 23 511 80 24 10 3 1 -1% 64 1 917 125 1042 890 124 1014 -27 -1 -28 2% 64 19 1118 138 119 965 141 103 -153 3 -16 13% 64 37 1202 151 94 1136 150 81 -66 -1 -13 5% 64 55 1118 141 61 1072 140 58 -46 -1 -3 4% 90 1 1342 177 1519 1275 174 1450 -67 -3 -69 4% 90 19 2392 199 192 2116 189 176 -276 -10 -16 11% 90 37 3313 238 175 2972 225 145 -341 -13 -30 10% 90 55 1948 210 104 1843 213 100 -105 3 -4 5% Notes: 1) This test ran a memory hog program that started a specified number N of threads, and had each thread allocate and touch 1/N'th of the total memory to be used in the test run in a single loop, writing a constant word to memory, one store every 4096 bytes. Watching this test during some earlier trial runs, I would see each of these threads sit down on one CPU and stay there, for the remainder of the pass, a different CPU for each thread. 2) The 'real' column is not comparable to the 'sys' or 'user' columns. The 'real' column is seconds wall clock time elapsed, from beginning to end of that test pass. The 'sys' and 'user' columns are total CPU seconds spent on that test pass. For a 19 thread test run, for example, the sum of 'sys' and 'user' could be up to 19 times the number of 'real' elapsed wall clock seconds. 3) Tests were run on a fresh, single-user boot, to minimize the amount of memory already in use at the start of the test, and to minimize the amount of background activity that might interfere. 4) Tests were done on a 56 CPU, 28 Node system with 96 GBytes of RAM. 5) Notice that the 'real' time gets large for the single thread runs, even though the measured 'sys' and 'user' times are modest. I'm not sure what that means - probably something to do with it being slow for one thread to be accessing memory along ways away. Perhaps the fake numa system, running ostensibly the same workload, would not show this substantial degradation of 'real' time for one thread on many nodes -- lets hope not. 6) The high thread count passes (one thread per CPU - on 55 of 56 CPUs) ran quite efficiently, as one might expect. Each pair of threads needed to allocate and touch the memory on the node the two threads shared, a pleasantly parallizable workload. 7) The intermediate thread count passes, when asking for alot of memory forcing them to go to a few neighboring nodes, improved the most with this zonelist caching patch. Conclusions: * This zonelist cache patch probably makes little difference one way or the other for most workloads on real numa hardware, if those workloads avoid heavy off node allocations. * For memory intensive workloads requiring substantial off-node allocations on real numa hardware, this patch improves both kernel and elapsed timings up to ten per-cent. * For fake numa systems, I'm optimistic, but will have to leave that up to Rohit Seth to actually test (once I get him a 2.6.18 backport.) Signed-off-by: Paul Jackson <pj@sgi.com> Cc: Rohit Seth <rohitseth@google.com> Cc: Christoph Lameter <clameter@engr.sgi.com> Cc: David Rientjes <rientjes@cs.washington.edu> Cc: Paul Menage <menage@google.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-07 11:31:48 +07:00
/*
* We cache key information from each zonelist for smaller cache
* footprint when scanning for free pages in get_page_from_freelist().
*
* 1) The BITMAP fullzones tracks which zones in a zonelist have come
* up short of free memory since the last time (last_fullzone_zap)
* we zero'd fullzones.
* 2) The array z_to_n[] maps each zone in the zonelist to its node
* id, so that we can efficiently evaluate whether that node is
* set in the current tasks mems_allowed.
*
* Both fullzones and z_to_n[] are one-to-one with the zonelist,
* indexed by a zones offset in the zonelist zones[] array.
*
* The get_page_from_freelist() routine does two scans. During the
* first scan, we skip zones whose corresponding bit in 'fullzones'
* is set or whose corresponding node in current->mems_allowed (which
* comes from cpusets) is not set. During the second scan, we bypass
* this zonelist_cache, to ensure we look methodically at each zone.
*
* Once per second, we zero out (zap) fullzones, forcing us to
* reconsider nodes that might have regained more free memory.
* The field last_full_zap is the time we last zapped fullzones.
*
* This mechanism reduces the amount of time we waste repeatedly
* reexaming zones for free memory when they just came up low on
* memory momentarilly ago.
*
* The zonelist_cache struct members logically belong in struct
* zonelist. However, the mempolicy zonelists constructed for
* MPOL_BIND are intentionally variable length (and usually much
* shorter). A general purpose mechanism for handling structs with
* multiple variable length members is more mechanism than we want
* here. We resort to some special case hackery instead.
*
* The MPOL_BIND zonelists don't need this zonelist_cache (in good
* part because they are shorter), so we put the fixed length stuff
* at the front of the zonelist struct, ending in a variable length
* zones[], as is needed by MPOL_BIND.
*
* Then we put the optional zonelist cache on the end of the zonelist
* struct. This optional stuff is found by a 'zlcache_ptr' pointer in
* the fixed length portion at the front of the struct. This pointer
* both enables us to find the zonelist cache, and in the case of
* MPOL_BIND zonelists, (which will just set the zlcache_ptr to NULL)
* to know that the zonelist cache is not there.
*
* The end result is that struct zonelists come in two flavors:
* 1) The full, fixed length version, shown below, and
* 2) The custom zonelists for MPOL_BIND.
* The custom MPOL_BIND zonelists have a NULL zlcache_ptr and no zlcache.
*
* Even though there may be multiple CPU cores on a node modifying
* fullzones or last_full_zap in the same zonelist_cache at the same
* time, we don't lock it. This is just hint data - if it is wrong now
* and then, the allocator will still function, perhaps a bit slower.
*/
struct zonelist_cache {
unsigned short z_to_n[MAX_ZONES_PER_ZONELIST]; /* zone->nid */
DECLARE_BITMAP(fullzones, MAX_ZONES_PER_ZONELIST); /* zone full? */
[PATCH] memory page_alloc zonelist caching speedup Optimize the critical zonelist scanning for free pages in the kernel memory allocator by caching the zones that were found to be full recently, and skipping them. Remembers the zones in a zonelist that were short of free memory in the last second. And it stashes a zone-to-node table in the zonelist struct, to optimize that conversion (minimize its cache footprint.) Recent changes: This differs in a significant way from a similar patch that I posted a week ago. Now, instead of having a nodemask_t of recently full nodes, I have a bitmask of recently full zones. This solves a problem that last weeks patch had, which on systems with multiple zones per node (such as DMA zone) would take seeing any of these zones full as meaning that all zones on that node were full. Also I changed names - from "zonelist faster" to "zonelist cache", as that seemed to better convey what we're doing here - caching some of the key zonelist state (for faster access.) See below for some performance benchmark results. After all that discussion with David on why I didn't need them, I went and got some ;). I wanted to verify that I had not hurt the normal case of memory allocation noticeably. At least for my one little microbenchmark, I found (1) the normal case wasn't affected, and (2) workloads that forced scanning across multiple nodes for memory improved up to 10% fewer System CPU cycles and lower elapsed clock time ('sys' and 'real'). Good. See details, below. I didn't have the logic in get_page_from_freelist() for various full nodes and zone reclaim failures correct. That should be fixed up now - notice the new goto labels zonelist_scan, this_zone_full, and try_next_zone, in get_page_from_freelist(). There are two reasons I persued this alternative, over some earlier proposals that would have focused on optimizing the fake numa emulation case by caching the last useful zone: 1) Contrary to what I said before, we (SGI, on large ia64 sn2 systems) have seen real customer loads where the cost to scan the zonelist was a problem, due to many nodes being full of memory before we got to a node we could use. Or at least, I think we have. This was related to me by another engineer, based on experiences from some time past. So this is not guaranteed. Most likely, though. The following approach should help such real numa systems just as much as it helps fake numa systems, or any combination thereof. 2) The effort to distinguish fake from real numa, using node_distance, so that we could cache a fake numa node and optimize choosing it over equivalent distance fake nodes, while continuing to properly scan all real nodes in distance order, was going to require a nasty blob of zonelist and node distance munging. The following approach has no new dependency on node distances or zone sorting. See comment in the patch below for a description of what it actually does. Technical details of note (or controversy): - See the use of "zlc_active" and "did_zlc_setup" below, to delay adding any work for this new mechanism until we've looked at the first zone in zonelist. I figured the odds of the first zone having the memory we needed were high enough that we should just look there, first, then get fancy only if we need to keep looking. - Some odd hackery was needed to add items to struct zonelist, while not tripping up the custom zonelists built by the mm/mempolicy.c code for MPOL_BIND. My usual wordy comments below explain this. Search for "MPOL_BIND". - Some per-node data in the struct zonelist is now modified frequently, with no locking. Multiple CPU cores on a node could hit and mangle this data. The theory is that this is just performance hint data, and the memory allocator will work just fine despite any such mangling. The fields at risk are the struct 'zonelist_cache' fields 'fullzones' (a bitmask) and 'last_full_zap' (unsigned long jiffies). It should all be self correcting after at most a one second delay. - This still does a linear scan of the same lengths as before. All I've optimized is making the scan faster, not algorithmically shorter. It is now able to scan a compact array of 'unsigned short' in the case of many full nodes, so one cache line should cover quite a few nodes, rather than each node hitting another one or two new and distinct cache lines. - If both Andi and Nick don't find this too complicated, I will be (pleasantly) flabbergasted. - I removed the comment claiming we only use one cachline's worth of zonelist. We seem, at least in the fake numa case, to have put the lie to that claim. - I pay no attention to the various watermarks and such in this performance hint. A node could be marked full for one watermark, and then skipped over when searching for a page using a different watermark. I think that's actually quite ok, as it will tend to slightly increase the spreading of memory over other nodes, away from a memory stressed node. =============== Performance - some benchmark results and analysis: This benchmark runs a memory hog program that uses multiple threads to touch alot of memory as quickly as it can. Multiple runs were made, touching 12, 38, 64 or 90 GBytes out of the total 96 GBytes on the system, and using 1, 19, 37, or 55 threads (on a 56 CPU system.) System, user and real (elapsed) timings were recorded for each run, shown in units of seconds, in the table below. Two kernels were tested - 2.6.18-mm3 and the same kernel with this zonelist caching patch added. The table also shows the percentage improvement the zonelist caching sys time is over (lower than) the stock *-mm kernel. number 2.6.18-mm3 zonelist-cache delta (< 0 good) percent GBs N ------------ -------------- ---------------- systime mem threads sys user real sys user real sys user real better 12 1 153 24 177 151 24 176 -2 0 -1 1% 12 19 99 22 8 99 22 8 0 0 0 0% 12 37 111 25 6 112 25 6 1 0 0 -0% 12 55 115 25 5 110 23 5 -5 -2 0 4% 38 1 502 74 576 497 73 570 -5 -1 -6 0% 38 19 426 78 48 373 76 39 -53 -2 -9 12% 38 37 544 83 36 547 82 36 3 -1 0 -0% 38 55 501 77 23 511 80 24 10 3 1 -1% 64 1 917 125 1042 890 124 1014 -27 -1 -28 2% 64 19 1118 138 119 965 141 103 -153 3 -16 13% 64 37 1202 151 94 1136 150 81 -66 -1 -13 5% 64 55 1118 141 61 1072 140 58 -46 -1 -3 4% 90 1 1342 177 1519 1275 174 1450 -67 -3 -69 4% 90 19 2392 199 192 2116 189 176 -276 -10 -16 11% 90 37 3313 238 175 2972 225 145 -341 -13 -30 10% 90 55 1948 210 104 1843 213 100 -105 3 -4 5% Notes: 1) This test ran a memory hog program that started a specified number N of threads, and had each thread allocate and touch 1/N'th of the total memory to be used in the test run in a single loop, writing a constant word to memory, one store every 4096 bytes. Watching this test during some earlier trial runs, I would see each of these threads sit down on one CPU and stay there, for the remainder of the pass, a different CPU for each thread. 2) The 'real' column is not comparable to the 'sys' or 'user' columns. The 'real' column is seconds wall clock time elapsed, from beginning to end of that test pass. The 'sys' and 'user' columns are total CPU seconds spent on that test pass. For a 19 thread test run, for example, the sum of 'sys' and 'user' could be up to 19 times the number of 'real' elapsed wall clock seconds. 3) Tests were run on a fresh, single-user boot, to minimize the amount of memory already in use at the start of the test, and to minimize the amount of background activity that might interfere. 4) Tests were done on a 56 CPU, 28 Node system with 96 GBytes of RAM. 5) Notice that the 'real' time gets large for the single thread runs, even though the measured 'sys' and 'user' times are modest. I'm not sure what that means - probably something to do with it being slow for one thread to be accessing memory along ways away. Perhaps the fake numa system, running ostensibly the same workload, would not show this substantial degradation of 'real' time for one thread on many nodes -- lets hope not. 6) The high thread count passes (one thread per CPU - on 55 of 56 CPUs) ran quite efficiently, as one might expect. Each pair of threads needed to allocate and touch the memory on the node the two threads shared, a pleasantly parallizable workload. 7) The intermediate thread count passes, when asking for alot of memory forcing them to go to a few neighboring nodes, improved the most with this zonelist caching patch. Conclusions: * This zonelist cache patch probably makes little difference one way or the other for most workloads on real numa hardware, if those workloads avoid heavy off node allocations. * For memory intensive workloads requiring substantial off-node allocations on real numa hardware, this patch improves both kernel and elapsed timings up to ten per-cent. * For fake numa systems, I'm optimistic, but will have to leave that up to Rohit Seth to actually test (once I get him a 2.6.18 backport.) Signed-off-by: Paul Jackson <pj@sgi.com> Cc: Rohit Seth <rohitseth@google.com> Cc: Christoph Lameter <clameter@engr.sgi.com> Cc: David Rientjes <rientjes@cs.washington.edu> Cc: Paul Menage <menage@google.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-07 11:31:48 +07:00
unsigned long last_full_zap; /* when last zap'd (jiffies) */
};
#else
#define MAX_ZONELISTS 1
[PATCH] memory page_alloc zonelist caching speedup Optimize the critical zonelist scanning for free pages in the kernel memory allocator by caching the zones that were found to be full recently, and skipping them. Remembers the zones in a zonelist that were short of free memory in the last second. And it stashes a zone-to-node table in the zonelist struct, to optimize that conversion (minimize its cache footprint.) Recent changes: This differs in a significant way from a similar patch that I posted a week ago. Now, instead of having a nodemask_t of recently full nodes, I have a bitmask of recently full zones. This solves a problem that last weeks patch had, which on systems with multiple zones per node (such as DMA zone) would take seeing any of these zones full as meaning that all zones on that node were full. Also I changed names - from "zonelist faster" to "zonelist cache", as that seemed to better convey what we're doing here - caching some of the key zonelist state (for faster access.) See below for some performance benchmark results. After all that discussion with David on why I didn't need them, I went and got some ;). I wanted to verify that I had not hurt the normal case of memory allocation noticeably. At least for my one little microbenchmark, I found (1) the normal case wasn't affected, and (2) workloads that forced scanning across multiple nodes for memory improved up to 10% fewer System CPU cycles and lower elapsed clock time ('sys' and 'real'). Good. See details, below. I didn't have the logic in get_page_from_freelist() for various full nodes and zone reclaim failures correct. That should be fixed up now - notice the new goto labels zonelist_scan, this_zone_full, and try_next_zone, in get_page_from_freelist(). There are two reasons I persued this alternative, over some earlier proposals that would have focused on optimizing the fake numa emulation case by caching the last useful zone: 1) Contrary to what I said before, we (SGI, on large ia64 sn2 systems) have seen real customer loads where the cost to scan the zonelist was a problem, due to many nodes being full of memory before we got to a node we could use. Or at least, I think we have. This was related to me by another engineer, based on experiences from some time past. So this is not guaranteed. Most likely, though. The following approach should help such real numa systems just as much as it helps fake numa systems, or any combination thereof. 2) The effort to distinguish fake from real numa, using node_distance, so that we could cache a fake numa node and optimize choosing it over equivalent distance fake nodes, while continuing to properly scan all real nodes in distance order, was going to require a nasty blob of zonelist and node distance munging. The following approach has no new dependency on node distances or zone sorting. See comment in the patch below for a description of what it actually does. Technical details of note (or controversy): - See the use of "zlc_active" and "did_zlc_setup" below, to delay adding any work for this new mechanism until we've looked at the first zone in zonelist. I figured the odds of the first zone having the memory we needed were high enough that we should just look there, first, then get fancy only if we need to keep looking. - Some odd hackery was needed to add items to struct zonelist, while not tripping up the custom zonelists built by the mm/mempolicy.c code for MPOL_BIND. My usual wordy comments below explain this. Search for "MPOL_BIND". - Some per-node data in the struct zonelist is now modified frequently, with no locking. Multiple CPU cores on a node could hit and mangle this data. The theory is that this is just performance hint data, and the memory allocator will work just fine despite any such mangling. The fields at risk are the struct 'zonelist_cache' fields 'fullzones' (a bitmask) and 'last_full_zap' (unsigned long jiffies). It should all be self correcting after at most a one second delay. - This still does a linear scan of the same lengths as before. All I've optimized is making the scan faster, not algorithmically shorter. It is now able to scan a compact array of 'unsigned short' in the case of many full nodes, so one cache line should cover quite a few nodes, rather than each node hitting another one or two new and distinct cache lines. - If both Andi and Nick don't find this too complicated, I will be (pleasantly) flabbergasted. - I removed the comment claiming we only use one cachline's worth of zonelist. We seem, at least in the fake numa case, to have put the lie to that claim. - I pay no attention to the various watermarks and such in this performance hint. A node could be marked full for one watermark, and then skipped over when searching for a page using a different watermark. I think that's actually quite ok, as it will tend to slightly increase the spreading of memory over other nodes, away from a memory stressed node. =============== Performance - some benchmark results and analysis: This benchmark runs a memory hog program that uses multiple threads to touch alot of memory as quickly as it can. Multiple runs were made, touching 12, 38, 64 or 90 GBytes out of the total 96 GBytes on the system, and using 1, 19, 37, or 55 threads (on a 56 CPU system.) System, user and real (elapsed) timings were recorded for each run, shown in units of seconds, in the table below. Two kernels were tested - 2.6.18-mm3 and the same kernel with this zonelist caching patch added. The table also shows the percentage improvement the zonelist caching sys time is over (lower than) the stock *-mm kernel. number 2.6.18-mm3 zonelist-cache delta (< 0 good) percent GBs N ------------ -------------- ---------------- systime mem threads sys user real sys user real sys user real better 12 1 153 24 177 151 24 176 -2 0 -1 1% 12 19 99 22 8 99 22 8 0 0 0 0% 12 37 111 25 6 112 25 6 1 0 0 -0% 12 55 115 25 5 110 23 5 -5 -2 0 4% 38 1 502 74 576 497 73 570 -5 -1 -6 0% 38 19 426 78 48 373 76 39 -53 -2 -9 12% 38 37 544 83 36 547 82 36 3 -1 0 -0% 38 55 501 77 23 511 80 24 10 3 1 -1% 64 1 917 125 1042 890 124 1014 -27 -1 -28 2% 64 19 1118 138 119 965 141 103 -153 3 -16 13% 64 37 1202 151 94 1136 150 81 -66 -1 -13 5% 64 55 1118 141 61 1072 140 58 -46 -1 -3 4% 90 1 1342 177 1519 1275 174 1450 -67 -3 -69 4% 90 19 2392 199 192 2116 189 176 -276 -10 -16 11% 90 37 3313 238 175 2972 225 145 -341 -13 -30 10% 90 55 1948 210 104 1843 213 100 -105 3 -4 5% Notes: 1) This test ran a memory hog program that started a specified number N of threads, and had each thread allocate and touch 1/N'th of the total memory to be used in the test run in a single loop, writing a constant word to memory, one store every 4096 bytes. Watching this test during some earlier trial runs, I would see each of these threads sit down on one CPU and stay there, for the remainder of the pass, a different CPU for each thread. 2) The 'real' column is not comparable to the 'sys' or 'user' columns. The 'real' column is seconds wall clock time elapsed, from beginning to end of that test pass. The 'sys' and 'user' columns are total CPU seconds spent on that test pass. For a 19 thread test run, for example, the sum of 'sys' and 'user' could be up to 19 times the number of 'real' elapsed wall clock seconds. 3) Tests were run on a fresh, single-user boot, to minimize the amount of memory already in use at the start of the test, and to minimize the amount of background activity that might interfere. 4) Tests were done on a 56 CPU, 28 Node system with 96 GBytes of RAM. 5) Notice that the 'real' time gets large for the single thread runs, even though the measured 'sys' and 'user' times are modest. I'm not sure what that means - probably something to do with it being slow for one thread to be accessing memory along ways away. Perhaps the fake numa system, running ostensibly the same workload, would not show this substantial degradation of 'real' time for one thread on many nodes -- lets hope not. 6) The high thread count passes (one thread per CPU - on 55 of 56 CPUs) ran quite efficiently, as one might expect. Each pair of threads needed to allocate and touch the memory on the node the two threads shared, a pleasantly parallizable workload. 7) The intermediate thread count passes, when asking for alot of memory forcing them to go to a few neighboring nodes, improved the most with this zonelist caching patch. Conclusions: * This zonelist cache patch probably makes little difference one way or the other for most workloads on real numa hardware, if those workloads avoid heavy off node allocations. * For memory intensive workloads requiring substantial off-node allocations on real numa hardware, this patch improves both kernel and elapsed timings up to ten per-cent. * For fake numa systems, I'm optimistic, but will have to leave that up to Rohit Seth to actually test (once I get him a 2.6.18 backport.) Signed-off-by: Paul Jackson <pj@sgi.com> Cc: Rohit Seth <rohitseth@google.com> Cc: Christoph Lameter <clameter@engr.sgi.com> Cc: David Rientjes <rientjes@cs.washington.edu> Cc: Paul Menage <menage@google.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-07 11:31:48 +07:00
struct zonelist_cache;
#endif
mm: have zonelist contains structs with both a zone pointer and zone_idx Filtering zonelists requires very frequent use of zone_idx(). This is costly as it involves a lookup of another structure and a substraction operation. As the zone_idx is often required, it should be quickly accessible. The node idx could also be stored here if it was found that accessing zone->node is significant which may be the case on workloads where nodemasks are heavily used. This patch introduces a struct zoneref to store a zone pointer and a zone index. The zonelist then consists of an array of these struct zonerefs which are looked up as necessary. Helpers are given for accessing the zone index as well as the node index. [kamezawa.hiroyu@jp.fujitsu.com: Suggested struct zoneref instead of embedding information in pointers] [hugh@veritas.com: mm-have-zonelist: fix memcg ooms] [hugh@veritas.com: just return do_try_to_free_pages] [hugh@veritas.com: do_try_to_free_pages gfp_mask redundant] Signed-off-by: Mel Gorman <mel@csn.ul.ie> Acked-by: Christoph Lameter <clameter@sgi.com> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Mel Gorman <mel@csn.ul.ie> Cc: Christoph Lameter <clameter@sgi.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Hugh Dickins <hugh@veritas.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 16:12:17 +07:00
/*
* This struct contains information about a zone in a zonelist. It is stored
* here to avoid dereferences into large structures and lookups of tables
*/
struct zoneref {
struct zone *zone; /* Pointer to actual zone */
int zone_idx; /* zone_idx(zoneref->zone) */
};
/*
* One allocation request operates on a zonelist. A zonelist
* is a list of zones, the first one is the 'goal' of the
* allocation, the other zones are fallback zones, in decreasing
* priority.
*
[PATCH] memory page_alloc zonelist caching speedup Optimize the critical zonelist scanning for free pages in the kernel memory allocator by caching the zones that were found to be full recently, and skipping them. Remembers the zones in a zonelist that were short of free memory in the last second. And it stashes a zone-to-node table in the zonelist struct, to optimize that conversion (minimize its cache footprint.) Recent changes: This differs in a significant way from a similar patch that I posted a week ago. Now, instead of having a nodemask_t of recently full nodes, I have a bitmask of recently full zones. This solves a problem that last weeks patch had, which on systems with multiple zones per node (such as DMA zone) would take seeing any of these zones full as meaning that all zones on that node were full. Also I changed names - from "zonelist faster" to "zonelist cache", as that seemed to better convey what we're doing here - caching some of the key zonelist state (for faster access.) See below for some performance benchmark results. After all that discussion with David on why I didn't need them, I went and got some ;). I wanted to verify that I had not hurt the normal case of memory allocation noticeably. At least for my one little microbenchmark, I found (1) the normal case wasn't affected, and (2) workloads that forced scanning across multiple nodes for memory improved up to 10% fewer System CPU cycles and lower elapsed clock time ('sys' and 'real'). Good. See details, below. I didn't have the logic in get_page_from_freelist() for various full nodes and zone reclaim failures correct. That should be fixed up now - notice the new goto labels zonelist_scan, this_zone_full, and try_next_zone, in get_page_from_freelist(). There are two reasons I persued this alternative, over some earlier proposals that would have focused on optimizing the fake numa emulation case by caching the last useful zone: 1) Contrary to what I said before, we (SGI, on large ia64 sn2 systems) have seen real customer loads where the cost to scan the zonelist was a problem, due to many nodes being full of memory before we got to a node we could use. Or at least, I think we have. This was related to me by another engineer, based on experiences from some time past. So this is not guaranteed. Most likely, though. The following approach should help such real numa systems just as much as it helps fake numa systems, or any combination thereof. 2) The effort to distinguish fake from real numa, using node_distance, so that we could cache a fake numa node and optimize choosing it over equivalent distance fake nodes, while continuing to properly scan all real nodes in distance order, was going to require a nasty blob of zonelist and node distance munging. The following approach has no new dependency on node distances or zone sorting. See comment in the patch below for a description of what it actually does. Technical details of note (or controversy): - See the use of "zlc_active" and "did_zlc_setup" below, to delay adding any work for this new mechanism until we've looked at the first zone in zonelist. I figured the odds of the first zone having the memory we needed were high enough that we should just look there, first, then get fancy only if we need to keep looking. - Some odd hackery was needed to add items to struct zonelist, while not tripping up the custom zonelists built by the mm/mempolicy.c code for MPOL_BIND. My usual wordy comments below explain this. Search for "MPOL_BIND". - Some per-node data in the struct zonelist is now modified frequently, with no locking. Multiple CPU cores on a node could hit and mangle this data. The theory is that this is just performance hint data, and the memory allocator will work just fine despite any such mangling. The fields at risk are the struct 'zonelist_cache' fields 'fullzones' (a bitmask) and 'last_full_zap' (unsigned long jiffies). It should all be self correcting after at most a one second delay. - This still does a linear scan of the same lengths as before. All I've optimized is making the scan faster, not algorithmically shorter. It is now able to scan a compact array of 'unsigned short' in the case of many full nodes, so one cache line should cover quite a few nodes, rather than each node hitting another one or two new and distinct cache lines. - If both Andi and Nick don't find this too complicated, I will be (pleasantly) flabbergasted. - I removed the comment claiming we only use one cachline's worth of zonelist. We seem, at least in the fake numa case, to have put the lie to that claim. - I pay no attention to the various watermarks and such in this performance hint. A node could be marked full for one watermark, and then skipped over when searching for a page using a different watermark. I think that's actually quite ok, as it will tend to slightly increase the spreading of memory over other nodes, away from a memory stressed node. =============== Performance - some benchmark results and analysis: This benchmark runs a memory hog program that uses multiple threads to touch alot of memory as quickly as it can. Multiple runs were made, touching 12, 38, 64 or 90 GBytes out of the total 96 GBytes on the system, and using 1, 19, 37, or 55 threads (on a 56 CPU system.) System, user and real (elapsed) timings were recorded for each run, shown in units of seconds, in the table below. Two kernels were tested - 2.6.18-mm3 and the same kernel with this zonelist caching patch added. The table also shows the percentage improvement the zonelist caching sys time is over (lower than) the stock *-mm kernel. number 2.6.18-mm3 zonelist-cache delta (< 0 good) percent GBs N ------------ -------------- ---------------- systime mem threads sys user real sys user real sys user real better 12 1 153 24 177 151 24 176 -2 0 -1 1% 12 19 99 22 8 99 22 8 0 0 0 0% 12 37 111 25 6 112 25 6 1 0 0 -0% 12 55 115 25 5 110 23 5 -5 -2 0 4% 38 1 502 74 576 497 73 570 -5 -1 -6 0% 38 19 426 78 48 373 76 39 -53 -2 -9 12% 38 37 544 83 36 547 82 36 3 -1 0 -0% 38 55 501 77 23 511 80 24 10 3 1 -1% 64 1 917 125 1042 890 124 1014 -27 -1 -28 2% 64 19 1118 138 119 965 141 103 -153 3 -16 13% 64 37 1202 151 94 1136 150 81 -66 -1 -13 5% 64 55 1118 141 61 1072 140 58 -46 -1 -3 4% 90 1 1342 177 1519 1275 174 1450 -67 -3 -69 4% 90 19 2392 199 192 2116 189 176 -276 -10 -16 11% 90 37 3313 238 175 2972 225 145 -341 -13 -30 10% 90 55 1948 210 104 1843 213 100 -105 3 -4 5% Notes: 1) This test ran a memory hog program that started a specified number N of threads, and had each thread allocate and touch 1/N'th of the total memory to be used in the test run in a single loop, writing a constant word to memory, one store every 4096 bytes. Watching this test during some earlier trial runs, I would see each of these threads sit down on one CPU and stay there, for the remainder of the pass, a different CPU for each thread. 2) The 'real' column is not comparable to the 'sys' or 'user' columns. The 'real' column is seconds wall clock time elapsed, from beginning to end of that test pass. The 'sys' and 'user' columns are total CPU seconds spent on that test pass. For a 19 thread test run, for example, the sum of 'sys' and 'user' could be up to 19 times the number of 'real' elapsed wall clock seconds. 3) Tests were run on a fresh, single-user boot, to minimize the amount of memory already in use at the start of the test, and to minimize the amount of background activity that might interfere. 4) Tests were done on a 56 CPU, 28 Node system with 96 GBytes of RAM. 5) Notice that the 'real' time gets large for the single thread runs, even though the measured 'sys' and 'user' times are modest. I'm not sure what that means - probably something to do with it being slow for one thread to be accessing memory along ways away. Perhaps the fake numa system, running ostensibly the same workload, would not show this substantial degradation of 'real' time for one thread on many nodes -- lets hope not. 6) The high thread count passes (one thread per CPU - on 55 of 56 CPUs) ran quite efficiently, as one might expect. Each pair of threads needed to allocate and touch the memory on the node the two threads shared, a pleasantly parallizable workload. 7) The intermediate thread count passes, when asking for alot of memory forcing them to go to a few neighboring nodes, improved the most with this zonelist caching patch. Conclusions: * This zonelist cache patch probably makes little difference one way or the other for most workloads on real numa hardware, if those workloads avoid heavy off node allocations. * For memory intensive workloads requiring substantial off-node allocations on real numa hardware, this patch improves both kernel and elapsed timings up to ten per-cent. * For fake numa systems, I'm optimistic, but will have to leave that up to Rohit Seth to actually test (once I get him a 2.6.18 backport.) Signed-off-by: Paul Jackson <pj@sgi.com> Cc: Rohit Seth <rohitseth@google.com> Cc: Christoph Lameter <clameter@engr.sgi.com> Cc: David Rientjes <rientjes@cs.washington.edu> Cc: Paul Menage <menage@google.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-07 11:31:48 +07:00
* If zlcache_ptr is not NULL, then it is just the address of zlcache,
* as explained above. If zlcache_ptr is NULL, there is no zlcache.
mm: have zonelist contains structs with both a zone pointer and zone_idx Filtering zonelists requires very frequent use of zone_idx(). This is costly as it involves a lookup of another structure and a substraction operation. As the zone_idx is often required, it should be quickly accessible. The node idx could also be stored here if it was found that accessing zone->node is significant which may be the case on workloads where nodemasks are heavily used. This patch introduces a struct zoneref to store a zone pointer and a zone index. The zonelist then consists of an array of these struct zonerefs which are looked up as necessary. Helpers are given for accessing the zone index as well as the node index. [kamezawa.hiroyu@jp.fujitsu.com: Suggested struct zoneref instead of embedding information in pointers] [hugh@veritas.com: mm-have-zonelist: fix memcg ooms] [hugh@veritas.com: just return do_try_to_free_pages] [hugh@veritas.com: do_try_to_free_pages gfp_mask redundant] Signed-off-by: Mel Gorman <mel@csn.ul.ie> Acked-by: Christoph Lameter <clameter@sgi.com> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Mel Gorman <mel@csn.ul.ie> Cc: Christoph Lameter <clameter@sgi.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Hugh Dickins <hugh@veritas.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 16:12:17 +07:00
* *
* To speed the reading of the zonelist, the zonerefs contain the zone index
* of the entry being read. Helper functions to access information given
* a struct zoneref are
*
* zonelist_zone() - Return the struct zone * for an entry in _zonerefs
* zonelist_zone_idx() - Return the index of the zone for an entry
* zonelist_node_idx() - Return the index of the node for an entry
*/
struct zonelist {
[PATCH] memory page_alloc zonelist caching speedup Optimize the critical zonelist scanning for free pages in the kernel memory allocator by caching the zones that were found to be full recently, and skipping them. Remembers the zones in a zonelist that were short of free memory in the last second. And it stashes a zone-to-node table in the zonelist struct, to optimize that conversion (minimize its cache footprint.) Recent changes: This differs in a significant way from a similar patch that I posted a week ago. Now, instead of having a nodemask_t of recently full nodes, I have a bitmask of recently full zones. This solves a problem that last weeks patch had, which on systems with multiple zones per node (such as DMA zone) would take seeing any of these zones full as meaning that all zones on that node were full. Also I changed names - from "zonelist faster" to "zonelist cache", as that seemed to better convey what we're doing here - caching some of the key zonelist state (for faster access.) See below for some performance benchmark results. After all that discussion with David on why I didn't need them, I went and got some ;). I wanted to verify that I had not hurt the normal case of memory allocation noticeably. At least for my one little microbenchmark, I found (1) the normal case wasn't affected, and (2) workloads that forced scanning across multiple nodes for memory improved up to 10% fewer System CPU cycles and lower elapsed clock time ('sys' and 'real'). Good. See details, below. I didn't have the logic in get_page_from_freelist() for various full nodes and zone reclaim failures correct. That should be fixed up now - notice the new goto labels zonelist_scan, this_zone_full, and try_next_zone, in get_page_from_freelist(). There are two reasons I persued this alternative, over some earlier proposals that would have focused on optimizing the fake numa emulation case by caching the last useful zone: 1) Contrary to what I said before, we (SGI, on large ia64 sn2 systems) have seen real customer loads where the cost to scan the zonelist was a problem, due to many nodes being full of memory before we got to a node we could use. Or at least, I think we have. This was related to me by another engineer, based on experiences from some time past. So this is not guaranteed. Most likely, though. The following approach should help such real numa systems just as much as it helps fake numa systems, or any combination thereof. 2) The effort to distinguish fake from real numa, using node_distance, so that we could cache a fake numa node and optimize choosing it over equivalent distance fake nodes, while continuing to properly scan all real nodes in distance order, was going to require a nasty blob of zonelist and node distance munging. The following approach has no new dependency on node distances or zone sorting. See comment in the patch below for a description of what it actually does. Technical details of note (or controversy): - See the use of "zlc_active" and "did_zlc_setup" below, to delay adding any work for this new mechanism until we've looked at the first zone in zonelist. I figured the odds of the first zone having the memory we needed were high enough that we should just look there, first, then get fancy only if we need to keep looking. - Some odd hackery was needed to add items to struct zonelist, while not tripping up the custom zonelists built by the mm/mempolicy.c code for MPOL_BIND. My usual wordy comments below explain this. Search for "MPOL_BIND". - Some per-node data in the struct zonelist is now modified frequently, with no locking. Multiple CPU cores on a node could hit and mangle this data. The theory is that this is just performance hint data, and the memory allocator will work just fine despite any such mangling. The fields at risk are the struct 'zonelist_cache' fields 'fullzones' (a bitmask) and 'last_full_zap' (unsigned long jiffies). It should all be self correcting after at most a one second delay. - This still does a linear scan of the same lengths as before. All I've optimized is making the scan faster, not algorithmically shorter. It is now able to scan a compact array of 'unsigned short' in the case of many full nodes, so one cache line should cover quite a few nodes, rather than each node hitting another one or two new and distinct cache lines. - If both Andi and Nick don't find this too complicated, I will be (pleasantly) flabbergasted. - I removed the comment claiming we only use one cachline's worth of zonelist. We seem, at least in the fake numa case, to have put the lie to that claim. - I pay no attention to the various watermarks and such in this performance hint. A node could be marked full for one watermark, and then skipped over when searching for a page using a different watermark. I think that's actually quite ok, as it will tend to slightly increase the spreading of memory over other nodes, away from a memory stressed node. =============== Performance - some benchmark results and analysis: This benchmark runs a memory hog program that uses multiple threads to touch alot of memory as quickly as it can. Multiple runs were made, touching 12, 38, 64 or 90 GBytes out of the total 96 GBytes on the system, and using 1, 19, 37, or 55 threads (on a 56 CPU system.) System, user and real (elapsed) timings were recorded for each run, shown in units of seconds, in the table below. Two kernels were tested - 2.6.18-mm3 and the same kernel with this zonelist caching patch added. The table also shows the percentage improvement the zonelist caching sys time is over (lower than) the stock *-mm kernel. number 2.6.18-mm3 zonelist-cache delta (< 0 good) percent GBs N ------------ -------------- ---------------- systime mem threads sys user real sys user real sys user real better 12 1 153 24 177 151 24 176 -2 0 -1 1% 12 19 99 22 8 99 22 8 0 0 0 0% 12 37 111 25 6 112 25 6 1 0 0 -0% 12 55 115 25 5 110 23 5 -5 -2 0 4% 38 1 502 74 576 497 73 570 -5 -1 -6 0% 38 19 426 78 48 373 76 39 -53 -2 -9 12% 38 37 544 83 36 547 82 36 3 -1 0 -0% 38 55 501 77 23 511 80 24 10 3 1 -1% 64 1 917 125 1042 890 124 1014 -27 -1 -28 2% 64 19 1118 138 119 965 141 103 -153 3 -16 13% 64 37 1202 151 94 1136 150 81 -66 -1 -13 5% 64 55 1118 141 61 1072 140 58 -46 -1 -3 4% 90 1 1342 177 1519 1275 174 1450 -67 -3 -69 4% 90 19 2392 199 192 2116 189 176 -276 -10 -16 11% 90 37 3313 238 175 2972 225 145 -341 -13 -30 10% 90 55 1948 210 104 1843 213 100 -105 3 -4 5% Notes: 1) This test ran a memory hog program that started a specified number N of threads, and had each thread allocate and touch 1/N'th of the total memory to be used in the test run in a single loop, writing a constant word to memory, one store every 4096 bytes. Watching this test during some earlier trial runs, I would see each of these threads sit down on one CPU and stay there, for the remainder of the pass, a different CPU for each thread. 2) The 'real' column is not comparable to the 'sys' or 'user' columns. The 'real' column is seconds wall clock time elapsed, from beginning to end of that test pass. The 'sys' and 'user' columns are total CPU seconds spent on that test pass. For a 19 thread test run, for example, the sum of 'sys' and 'user' could be up to 19 times the number of 'real' elapsed wall clock seconds. 3) Tests were run on a fresh, single-user boot, to minimize the amount of memory already in use at the start of the test, and to minimize the amount of background activity that might interfere. 4) Tests were done on a 56 CPU, 28 Node system with 96 GBytes of RAM. 5) Notice that the 'real' time gets large for the single thread runs, even though the measured 'sys' and 'user' times are modest. I'm not sure what that means - probably something to do with it being slow for one thread to be accessing memory along ways away. Perhaps the fake numa system, running ostensibly the same workload, would not show this substantial degradation of 'real' time for one thread on many nodes -- lets hope not. 6) The high thread count passes (one thread per CPU - on 55 of 56 CPUs) ran quite efficiently, as one might expect. Each pair of threads needed to allocate and touch the memory on the node the two threads shared, a pleasantly parallizable workload. 7) The intermediate thread count passes, when asking for alot of memory forcing them to go to a few neighboring nodes, improved the most with this zonelist caching patch. Conclusions: * This zonelist cache patch probably makes little difference one way or the other for most workloads on real numa hardware, if those workloads avoid heavy off node allocations. * For memory intensive workloads requiring substantial off-node allocations on real numa hardware, this patch improves both kernel and elapsed timings up to ten per-cent. * For fake numa systems, I'm optimistic, but will have to leave that up to Rohit Seth to actually test (once I get him a 2.6.18 backport.) Signed-off-by: Paul Jackson <pj@sgi.com> Cc: Rohit Seth <rohitseth@google.com> Cc: Christoph Lameter <clameter@engr.sgi.com> Cc: David Rientjes <rientjes@cs.washington.edu> Cc: Paul Menage <menage@google.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-07 11:31:48 +07:00
struct zonelist_cache *zlcache_ptr; // NULL or &zlcache
mm: have zonelist contains structs with both a zone pointer and zone_idx Filtering zonelists requires very frequent use of zone_idx(). This is costly as it involves a lookup of another structure and a substraction operation. As the zone_idx is often required, it should be quickly accessible. The node idx could also be stored here if it was found that accessing zone->node is significant which may be the case on workloads where nodemasks are heavily used. This patch introduces a struct zoneref to store a zone pointer and a zone index. The zonelist then consists of an array of these struct zonerefs which are looked up as necessary. Helpers are given for accessing the zone index as well as the node index. [kamezawa.hiroyu@jp.fujitsu.com: Suggested struct zoneref instead of embedding information in pointers] [hugh@veritas.com: mm-have-zonelist: fix memcg ooms] [hugh@veritas.com: just return do_try_to_free_pages] [hugh@veritas.com: do_try_to_free_pages gfp_mask redundant] Signed-off-by: Mel Gorman <mel@csn.ul.ie> Acked-by: Christoph Lameter <clameter@sgi.com> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Mel Gorman <mel@csn.ul.ie> Cc: Christoph Lameter <clameter@sgi.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Hugh Dickins <hugh@veritas.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 16:12:17 +07:00
struct zoneref _zonerefs[MAX_ZONES_PER_ZONELIST + 1];
[PATCH] memory page_alloc zonelist caching speedup Optimize the critical zonelist scanning for free pages in the kernel memory allocator by caching the zones that were found to be full recently, and skipping them. Remembers the zones in a zonelist that were short of free memory in the last second. And it stashes a zone-to-node table in the zonelist struct, to optimize that conversion (minimize its cache footprint.) Recent changes: This differs in a significant way from a similar patch that I posted a week ago. Now, instead of having a nodemask_t of recently full nodes, I have a bitmask of recently full zones. This solves a problem that last weeks patch had, which on systems with multiple zones per node (such as DMA zone) would take seeing any of these zones full as meaning that all zones on that node were full. Also I changed names - from "zonelist faster" to "zonelist cache", as that seemed to better convey what we're doing here - caching some of the key zonelist state (for faster access.) See below for some performance benchmark results. After all that discussion with David on why I didn't need them, I went and got some ;). I wanted to verify that I had not hurt the normal case of memory allocation noticeably. At least for my one little microbenchmark, I found (1) the normal case wasn't affected, and (2) workloads that forced scanning across multiple nodes for memory improved up to 10% fewer System CPU cycles and lower elapsed clock time ('sys' and 'real'). Good. See details, below. I didn't have the logic in get_page_from_freelist() for various full nodes and zone reclaim failures correct. That should be fixed up now - notice the new goto labels zonelist_scan, this_zone_full, and try_next_zone, in get_page_from_freelist(). There are two reasons I persued this alternative, over some earlier proposals that would have focused on optimizing the fake numa emulation case by caching the last useful zone: 1) Contrary to what I said before, we (SGI, on large ia64 sn2 systems) have seen real customer loads where the cost to scan the zonelist was a problem, due to many nodes being full of memory before we got to a node we could use. Or at least, I think we have. This was related to me by another engineer, based on experiences from some time past. So this is not guaranteed. Most likely, though. The following approach should help such real numa systems just as much as it helps fake numa systems, or any combination thereof. 2) The effort to distinguish fake from real numa, using node_distance, so that we could cache a fake numa node and optimize choosing it over equivalent distance fake nodes, while continuing to properly scan all real nodes in distance order, was going to require a nasty blob of zonelist and node distance munging. The following approach has no new dependency on node distances or zone sorting. See comment in the patch below for a description of what it actually does. Technical details of note (or controversy): - See the use of "zlc_active" and "did_zlc_setup" below, to delay adding any work for this new mechanism until we've looked at the first zone in zonelist. I figured the odds of the first zone having the memory we needed were high enough that we should just look there, first, then get fancy only if we need to keep looking. - Some odd hackery was needed to add items to struct zonelist, while not tripping up the custom zonelists built by the mm/mempolicy.c code for MPOL_BIND. My usual wordy comments below explain this. Search for "MPOL_BIND". - Some per-node data in the struct zonelist is now modified frequently, with no locking. Multiple CPU cores on a node could hit and mangle this data. The theory is that this is just performance hint data, and the memory allocator will work just fine despite any such mangling. The fields at risk are the struct 'zonelist_cache' fields 'fullzones' (a bitmask) and 'last_full_zap' (unsigned long jiffies). It should all be self correcting after at most a one second delay. - This still does a linear scan of the same lengths as before. All I've optimized is making the scan faster, not algorithmically shorter. It is now able to scan a compact array of 'unsigned short' in the case of many full nodes, so one cache line should cover quite a few nodes, rather than each node hitting another one or two new and distinct cache lines. - If both Andi and Nick don't find this too complicated, I will be (pleasantly) flabbergasted. - I removed the comment claiming we only use one cachline's worth of zonelist. We seem, at least in the fake numa case, to have put the lie to that claim. - I pay no attention to the various watermarks and such in this performance hint. A node could be marked full for one watermark, and then skipped over when searching for a page using a different watermark. I think that's actually quite ok, as it will tend to slightly increase the spreading of memory over other nodes, away from a memory stressed node. =============== Performance - some benchmark results and analysis: This benchmark runs a memory hog program that uses multiple threads to touch alot of memory as quickly as it can. Multiple runs were made, touching 12, 38, 64 or 90 GBytes out of the total 96 GBytes on the system, and using 1, 19, 37, or 55 threads (on a 56 CPU system.) System, user and real (elapsed) timings were recorded for each run, shown in units of seconds, in the table below. Two kernels were tested - 2.6.18-mm3 and the same kernel with this zonelist caching patch added. The table also shows the percentage improvement the zonelist caching sys time is over (lower than) the stock *-mm kernel. number 2.6.18-mm3 zonelist-cache delta (< 0 good) percent GBs N ------------ -------------- ---------------- systime mem threads sys user real sys user real sys user real better 12 1 153 24 177 151 24 176 -2 0 -1 1% 12 19 99 22 8 99 22 8 0 0 0 0% 12 37 111 25 6 112 25 6 1 0 0 -0% 12 55 115 25 5 110 23 5 -5 -2 0 4% 38 1 502 74 576 497 73 570 -5 -1 -6 0% 38 19 426 78 48 373 76 39 -53 -2 -9 12% 38 37 544 83 36 547 82 36 3 -1 0 -0% 38 55 501 77 23 511 80 24 10 3 1 -1% 64 1 917 125 1042 890 124 1014 -27 -1 -28 2% 64 19 1118 138 119 965 141 103 -153 3 -16 13% 64 37 1202 151 94 1136 150 81 -66 -1 -13 5% 64 55 1118 141 61 1072 140 58 -46 -1 -3 4% 90 1 1342 177 1519 1275 174 1450 -67 -3 -69 4% 90 19 2392 199 192 2116 189 176 -276 -10 -16 11% 90 37 3313 238 175 2972 225 145 -341 -13 -30 10% 90 55 1948 210 104 1843 213 100 -105 3 -4 5% Notes: 1) This test ran a memory hog program that started a specified number N of threads, and had each thread allocate and touch 1/N'th of the total memory to be used in the test run in a single loop, writing a constant word to memory, one store every 4096 bytes. Watching this test during some earlier trial runs, I would see each of these threads sit down on one CPU and stay there, for the remainder of the pass, a different CPU for each thread. 2) The 'real' column is not comparable to the 'sys' or 'user' columns. The 'real' column is seconds wall clock time elapsed, from beginning to end of that test pass. The 'sys' and 'user' columns are total CPU seconds spent on that test pass. For a 19 thread test run, for example, the sum of 'sys' and 'user' could be up to 19 times the number of 'real' elapsed wall clock seconds. 3) Tests were run on a fresh, single-user boot, to minimize the amount of memory already in use at the start of the test, and to minimize the amount of background activity that might interfere. 4) Tests were done on a 56 CPU, 28 Node system with 96 GBytes of RAM. 5) Notice that the 'real' time gets large for the single thread runs, even though the measured 'sys' and 'user' times are modest. I'm not sure what that means - probably something to do with it being slow for one thread to be accessing memory along ways away. Perhaps the fake numa system, running ostensibly the same workload, would not show this substantial degradation of 'real' time for one thread on many nodes -- lets hope not. 6) The high thread count passes (one thread per CPU - on 55 of 56 CPUs) ran quite efficiently, as one might expect. Each pair of threads needed to allocate and touch the memory on the node the two threads shared, a pleasantly parallizable workload. 7) The intermediate thread count passes, when asking for alot of memory forcing them to go to a few neighboring nodes, improved the most with this zonelist caching patch. Conclusions: * This zonelist cache patch probably makes little difference one way or the other for most workloads on real numa hardware, if those workloads avoid heavy off node allocations. * For memory intensive workloads requiring substantial off-node allocations on real numa hardware, this patch improves both kernel and elapsed timings up to ten per-cent. * For fake numa systems, I'm optimistic, but will have to leave that up to Rohit Seth to actually test (once I get him a 2.6.18 backport.) Signed-off-by: Paul Jackson <pj@sgi.com> Cc: Rohit Seth <rohitseth@google.com> Cc: Christoph Lameter <clameter@engr.sgi.com> Cc: David Rientjes <rientjes@cs.washington.edu> Cc: Paul Menage <menage@google.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-07 11:31:48 +07:00
#ifdef CONFIG_NUMA
struct zonelist_cache zlcache; // optional ...
#endif
};
#ifdef CONFIG_HAVE_MEMBLOCK_NODE_MAP
[PATCH] Introduce mechanism for registering active regions of memory At a basic level, architectures define structures to record where active ranges of page frames are located. Once located, the code to calculate zone sizes and holes in each architecture is very similar. Some of this zone and hole sizing code is difficult to read for no good reason. This set of patches eliminates the similar-looking architecture-specific code. The patches introduce a mechanism where architectures register where the active ranges of page frames are with add_active_range(). When all areas have been discovered, free_area_init_nodes() is called to initialise the pgdat and zones. The zone sizes and holes are then calculated in an architecture independent manner. Patch 1 introduces the mechanism for registering and initialising PFN ranges Patch 2 changes ppc to use the mechanism - 139 arch-specific LOC removed Patch 3 changes x86 to use the mechanism - 136 arch-specific LOC removed Patch 4 changes x86_64 to use the mechanism - 74 arch-specific LOC removed Patch 5 changes ia64 to use the mechanism - 52 arch-specific LOC removed Patch 6 accounts for mem_map as a memory hole as the pages are not reclaimable. It adjusts the watermarks slightly Tony Luck has successfully tested for ia64 on Itanium with tiger_defconfig, gensparse_defconfig and defconfig. Bob Picco has also tested and debugged on IA64. Jack Steiner successfully boot tested on a mammoth SGI IA64-based machine. These were on patches against 2.6.17-rc1 and release 3 of these patches but there have been no ia64-changes since release 3. There are differences in the zone sizes for x86_64 as the arch-specific code for x86_64 accounts the kernel image and the starting mem_maps as memory holes but the architecture-independent code accounts the memory as present. The big benefit of this set of patches is a sizable reduction of architecture-specific code, some of which is very hairy. There should be a greater reduction when other architectures use the same mechanisms for zone and hole sizing but I lack the hardware to test on. Additional credit; Dave Hansen for the initial suggestion and comments on early patches Andy Whitcroft for reviewing early versions and catching numerous errors Tony Luck for testing and debugging on IA64 Bob Picco for fixing bugs related to pfn registration, reviewing a number of patch revisions, providing a number of suggestions on future direction and testing heavily Jack Steiner and Robin Holt for testing on IA64 and clarifying issues related to memory holes Yasunori for testing on IA64 Andi Kleen for reviewing and feeding back about x86_64 Christian Kujau for providing valuable information related to ACPI problems on x86_64 and testing potential fixes This patch: Define the structure to represent an active range of page frames within a node in an architecture independent manner. Architectures are expected to register active ranges of PFNs using add_active_range(nid, start_pfn, end_pfn) and call free_area_init_nodes() passing the PFNs of the end of each zone. Signed-off-by: Mel Gorman <mel@csn.ul.ie> Signed-off-by: Bob Picco <bob.picco@hp.com> Cc: Dave Hansen <haveblue@us.ibm.com> Cc: Andy Whitcroft <apw@shadowen.org> Cc: Andi Kleen <ak@muc.de> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: "Keith Mannthey" <kmannth@gmail.com> Cc: "Luck, Tony" <tony.luck@intel.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Yasunori Goto <y-goto@jp.fujitsu.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-09-27 15:49:43 +07:00
struct node_active_region {
unsigned long start_pfn;
unsigned long end_pfn;
int nid;
};
#endif /* CONFIG_HAVE_MEMBLOCK_NODE_MAP */
#ifndef CONFIG_DISCONTIGMEM
/* The array of struct pages - for discontigmem use pgdat->lmem_map */
extern struct page *mem_map;
#endif
/*
* The pg_data_t structure is used in machines with CONFIG_DISCONTIGMEM
* (mostly NUMA machines?) to denote a higher-level memory zone than the
* zone denotes.
*
* On NUMA machines, each NUMA node would have a pg_data_t to describe
* it's memory layout.
*
* Memory statistics and page replacement data structures are maintained on a
* per-zone basis.
*/
struct bootmem_data;
typedef struct pglist_data {
struct zone node_zones[MAX_NR_ZONES];
struct zonelist node_zonelists[MAX_ZONELISTS];
int nr_zones;
#ifdef CONFIG_FLAT_NODE_MEM_MAP /* means !SPARSEMEM */
struct page *node_mem_map;
mm/page_ext: resurrect struct page extending code for debugging When we debug something, we'd like to insert some information to every page. For this purpose, we sometimes modify struct page itself. But, this has drawbacks. First, it requires re-compile. This makes us hesitate to use the powerful debug feature so development process is slowed down. And, second, sometimes it is impossible to rebuild the kernel due to third party module dependency. At third, system behaviour would be largely different after re-compile, because it changes size of struct page greatly and this structure is accessed by every part of kernel. Keeping this as it is would be better to reproduce errornous situation. This feature is intended to overcome above mentioned problems. This feature allocates memory for extended data per page in certain place rather than the struct page itself. This memory can be accessed by the accessor functions provided by this code. During the boot process, it checks whether allocation of huge chunk of memory is needed or not. If not, it avoids allocating memory at all. With this advantage, we can include this feature into the kernel in default and can avoid rebuild and solve related problems. Until now, memcg uses this technique. But, now, memcg decides to embed their variable to struct page itself and it's code to extend struct page has been removed. I'd like to use this code to develop debug feature, so this patch resurrect it. To help these things to work well, this patch introduces two callbacks for clients. One is the need callback which is mandatory if user wants to avoid useless memory allocation at boot-time. The other is optional, init callback, which is used to do proper initialization after memory is allocated. Detailed explanation about purpose of these functions is in code comment. Please refer it. Others are completely same with previous extension code in memcg. Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Minchan Kim <minchan@kernel.org> Cc: Dave Hansen <dave@sr71.net> Cc: Michal Nazarewicz <mina86@mina86.com> Cc: Jungsoo Son <jungsoo.son@lge.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-12-13 07:55:46 +07:00
#ifdef CONFIG_PAGE_EXTENSION
struct page_ext *node_page_ext;
#endif
[PATCH] sparsemem memory model Sparsemem abstracts the use of discontiguous mem_maps[]. This kind of mem_map[] is needed by discontiguous memory machines (like in the old CONFIG_DISCONTIGMEM case) as well as memory hotplug systems. Sparsemem replaces DISCONTIGMEM when enabled, and it is hoped that it can eventually become a complete replacement. A significant advantage over DISCONTIGMEM is that it's completely separated from CONFIG_NUMA. When producing this patch, it became apparent in that NUMA and DISCONTIG are often confused. Another advantage is that sparse doesn't require each NUMA node's ranges to be contiguous. It can handle overlapping ranges between nodes with no problems, where DISCONTIGMEM currently throws away that memory. Sparsemem uses an array to provide different pfn_to_page() translations for each SECTION_SIZE area of physical memory. This is what allows the mem_map[] to be chopped up. In order to do quick pfn_to_page() operations, the section number of the page is encoded in page->flags. Part of the sparsemem infrastructure enables sharing of these bits more dynamically (at compile-time) between the page_zone() and sparsemem operations. However, on 32-bit architectures, the number of bits is quite limited, and may require growing the size of the page->flags type in certain conditions. Several things might force this to occur: a decrease in the SECTION_SIZE (if you want to hotplug smaller areas of memory), an increase in the physical address space, or an increase in the number of used page->flags. One thing to note is that, once sparsemem is present, the NUMA node information no longer needs to be stored in the page->flags. It might provide speed increases on certain platforms and will be stored there if there is room. But, if out of room, an alternate (theoretically slower) mechanism is used. This patch introduces CONFIG_FLATMEM. It is used in almost all cases where there used to be an #ifndef DISCONTIG, because SPARSEMEM and DISCONTIGMEM often have to compile out the same areas of code. Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Dave Hansen <haveblue@us.ibm.com> Signed-off-by: Martin Bligh <mbligh@aracnet.com> Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com> Signed-off-by: Bob Picco <bob.picco@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 14:07:54 +07:00
#endif
#ifndef CONFIG_NO_BOOTMEM
struct bootmem_data *bdata;
#endif
#ifdef CONFIG_MEMORY_HOTPLUG
/*
* Must be held any time you expect node_start_pfn, node_present_pages
* or node_spanned_pages stay constant. Holding this will also
* guarantee that any pfn_valid() stays that way.
*
* pgdat_resize_lock() and pgdat_resize_unlock() are provided to
* manipulate node_size_lock without checking for CONFIG_MEMORY_HOTPLUG.
*
* Nests above zone->lock and zone->span_seqlock
*/
spinlock_t node_size_lock;
#endif
unsigned long node_start_pfn;
unsigned long node_present_pages; /* total number of physical pages */
unsigned long node_spanned_pages; /* total size of physical page
range, including holes */
int node_id;
wait_queue_head_t kswapd_wait;
wait_queue_head_t pfmemalloc_wait;
mem-hotplug: implement get/put_online_mems kmem_cache_{create,destroy,shrink} need to get a stable value of cpu/node online mask, because they init/destroy/access per-cpu/node kmem_cache parts, which can be allocated or destroyed on cpu/mem hotplug. To protect against cpu hotplug, these functions use {get,put}_online_cpus. However, they do nothing to synchronize with memory hotplug - taking the slab_mutex does not eliminate the possibility of race as described in patch 2. What we need there is something like get_online_cpus, but for memory. We already have lock_memory_hotplug, which serves for the purpose, but it's a bit of a hammer right now, because it's backed by a mutex. As a result, it imposes some limitations to locking order, which are not desirable, and can't be used just like get_online_cpus. That's why in patch 1 I substitute it with get/put_online_mems, which work exactly like get/put_online_cpus except they block not cpu, but memory hotplug. [ v1 can be found at https://lkml.org/lkml/2014/4/6/68. I NAK'ed it by myself, because it used an rw semaphore for get/put_online_mems, making them dead lock prune. ] This patch (of 2): {un}lock_memory_hotplug, which is used to synchronize against memory hotplug, is currently backed by a mutex, which makes it a bit of a hammer - threads that only want to get a stable value of online nodes mask won't be able to proceed concurrently. Also, it imposes some strong locking ordering rules on it, which narrows down the set of its usage scenarios. This patch introduces get/put_online_mems, which are the same as get/put_online_cpus, but for memory hotplug, i.e. executing a code inside a get/put_online_mems section will guarantee a stable value of online nodes, present pages, etc. lock_memory_hotplug()/unlock_memory_hotplug() are removed altogether. Signed-off-by: Vladimir Davydov <vdavydov@parallels.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: Tang Chen <tangchen@cn.fujitsu.com> Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com> Cc: Toshi Kani <toshi.kani@hp.com> Cc: Xishi Qiu <qiuxishi@huawei.com> Cc: Jiang Liu <liuj97@gmail.com> Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: David Rientjes <rientjes@google.com> Cc: Wen Congyang <wency@cn.fujitsu.com> Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> Cc: Lai Jiangshan <laijs@cn.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-06-05 06:07:18 +07:00
struct task_struct *kswapd; /* Protected by
mem_hotplug_begin/end() */
int kswapd_max_order;
mm: kswapd: stop high-order balancing when any suitable zone is balanced Simon Kirby reported the following problem We're seeing cases on a number of servers where cache never fully grows to use all available memory. Sometimes we see servers with 4 GB of memory that never seem to have less than 1.5 GB free, even with a constantly-active VM. In some cases, these servers also swap out while this happens, even though they are constantly reading the working set into memory. We have been seeing this happening for a long time; I don't think it's anything recent, and it still happens on 2.6.36. After some debugging work by Simon, Dave Hansen and others, the prevaling theory became that kswapd is reclaiming order-3 pages requested by SLUB too aggressive about it. There are two apparent problems here. On the target machine, there is a small Normal zone in comparison to DMA32. As kswapd tries to balance all zones, it would continually try reclaiming for Normal even though DMA32 was balanced enough for callers. The second problem is that sleeping_prematurely() does not use the same logic as balance_pgdat() when deciding whether to sleep or not. This keeps kswapd artifically awake. A number of tests were run and the figures from previous postings will look very different for a few reasons. One, the old figures were forcing my network card to use GFP_ATOMIC in attempt to replicate Simon's problem. Second, I previous specified slub_min_order=3 again in an attempt to reproduce Simon's problem. In this posting, I'm depending on Simon to say whether his problem is fixed or not and these figures are to show the impact to the ordinary cases. Finally, the "vmscan" figures are taken from /proc/vmstat instead of the tracepoints. There is less information but recording is less disruptive. The first test of relevance was postmark with a process running in the background reading a large amount of anonymous memory in blocks. The objective was to vaguely simulate what was happening on Simon's machine and it's memory intensive enough to have kswapd awake. POSTMARK traceonly kanyzone Transactions per second: 156.00 ( 0.00%) 153.00 (-1.96%) Data megabytes read per second: 21.51 ( 0.00%) 21.52 ( 0.05%) Data megabytes written per second: 29.28 ( 0.00%) 29.11 (-0.58%) Files created alone per second: 250.00 ( 0.00%) 416.00 (39.90%) Files create/transact per second: 79.00 ( 0.00%) 76.00 (-3.95%) Files deleted alone per second: 520.00 ( 0.00%) 420.00 (-23.81%) Files delete/transact per second: 79.00 ( 0.00%) 76.00 (-3.95%) MMTests Statistics: duration User/Sys Time Running Test (seconds) 16.58 17.4 Total Elapsed Time (seconds) 218.48 222.47 VMstat Reclaim Statistics: vmscan Direct reclaims 0 4 Direct reclaim pages scanned 0 203 Direct reclaim pages reclaimed 0 184 Kswapd pages scanned 326631 322018 Kswapd pages reclaimed 312632 309784 Kswapd low wmark quickly 1 4 Kswapd high wmark quickly 122 475 Kswapd skip congestion_wait 1 0 Pages activated 700040 705317 Pages deactivated 212113 203922 Pages written 9875 6363 Total pages scanned 326631 322221 Total pages reclaimed 312632 309968 %age total pages scanned/reclaimed 95.71% 96.20% %age total pages scanned/written 3.02% 1.97% proc vmstat: Faults Major Faults 300 254 Minor Faults 645183 660284 Page ins 493588 486704 Page outs 4960088 4986704 Swap ins 1230 661 Swap outs 9869 6355 Performance is mildly affected because kswapd is no longer doing as much work and the background memory consumer process is getting in the way. Note that kswapd scanned and reclaimed fewer pages as it's less aggressive and overall fewer pages were scanned and reclaimed. Swap in/out is particularly reduced again reflecting kswapd throwing out fewer pages. The slight performance impact is unfortunate here but it looks like a direct result of kswapd being less aggressive. As the bug report is about too many pages being freed by kswapd, it may have to be accepted for now. The second test is a streaming IO benchmark that was previously used by Johannes to show regressions in page reclaim. MICRO traceonly kanyzone User/Sys Time Running Test (seconds) 29.29 28.87 Total Elapsed Time (seconds) 492.18 488.79 VMstat Reclaim Statistics: vmscan Direct reclaims 2128 1460 Direct reclaim pages scanned 2284822 1496067 Direct reclaim pages reclaimed 148919 110937 Kswapd pages scanned 15450014 16202876 Kswapd pages reclaimed 8503697 8537897 Kswapd low wmark quickly 3100 3397 Kswapd high wmark quickly 1860 7243 Kswapd skip congestion_wait 708 801 Pages activated 9635 9573 Pages deactivated 1432 1271 Pages written 223 1130 Total pages scanned 17734836 17698943 Total pages reclaimed 8652616 8648834 %age total pages scanned/reclaimed 48.79% 48.87% %age total pages scanned/written 0.00% 0.01% proc vmstat: Faults Major Faults 165 221 Minor Faults 9655785 9656506 Page ins 3880 7228 Page outs 37692940 37480076 Swap ins 0 69 Swap outs 19 15 Again fewer pages are scanned and reclaimed as expected and this time the test completed faster. Note that kswapd is hitting its watermarks faster (low and high wmark quickly) which I expect is due to kswapd reclaiming fewer pages. I also ran fs-mark, iozone and sysbench but there is nothing interesting to report in the figures. Performance is not significantly changed and the reclaim statistics look reasonable. Tgis patch: When the allocator enters its slow path, kswapd is woken up to balance the node. It continues working until all zones within the node are balanced. For order-0 allocations, this makes perfect sense but for higher orders it can have unintended side-effects. If the zone sizes are imbalanced, kswapd may reclaim heavily within a smaller zone discarding an excessive number of pages. The user-visible behaviour is that kswapd is awake and reclaiming even though plenty of pages are free from a suitable zone. This patch alters the "balance" logic for high-order reclaim allowing kswapd to stop if any suitable zone becomes balanced to reduce the number of pages it reclaims from other zones. kswapd still tries to ensure that order-0 watermarks for all zones are met before sleeping. Signed-off-by: Mel Gorman <mel@csn.ul.ie> Reviewed-by: Minchan Kim <minchan.kim@gmail.com> Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Reviewed-by: Eric B Munson <emunson@mgebm.net> Cc: Simon Kirby <sim@hostway.ca> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Shaohua Li <shaohua.li@intel.com> Cc: Dave Hansen <dave@linux.vnet.ibm.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Rik van Riel <riel@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-01-14 06:46:20 +07:00
enum zone_type classzone_idx;
#ifdef CONFIG_NUMA_BALANCING
/* Lock serializing the migrate rate limiting window */
spinlock_t numabalancing_migrate_lock;
/* Rate limiting time interval */
unsigned long numabalancing_migrate_next_window;
/* Number of pages migrated during the rate limiting time interval */
unsigned long numabalancing_migrate_nr_pages;
#endif
} pg_data_t;
#define node_present_pages(nid) (NODE_DATA(nid)->node_present_pages)
#define node_spanned_pages(nid) (NODE_DATA(nid)->node_spanned_pages)
[PATCH] sparsemem memory model Sparsemem abstracts the use of discontiguous mem_maps[]. This kind of mem_map[] is needed by discontiguous memory machines (like in the old CONFIG_DISCONTIGMEM case) as well as memory hotplug systems. Sparsemem replaces DISCONTIGMEM when enabled, and it is hoped that it can eventually become a complete replacement. A significant advantage over DISCONTIGMEM is that it's completely separated from CONFIG_NUMA. When producing this patch, it became apparent in that NUMA and DISCONTIG are often confused. Another advantage is that sparse doesn't require each NUMA node's ranges to be contiguous. It can handle overlapping ranges between nodes with no problems, where DISCONTIGMEM currently throws away that memory. Sparsemem uses an array to provide different pfn_to_page() translations for each SECTION_SIZE area of physical memory. This is what allows the mem_map[] to be chopped up. In order to do quick pfn_to_page() operations, the section number of the page is encoded in page->flags. Part of the sparsemem infrastructure enables sharing of these bits more dynamically (at compile-time) between the page_zone() and sparsemem operations. However, on 32-bit architectures, the number of bits is quite limited, and may require growing the size of the page->flags type in certain conditions. Several things might force this to occur: a decrease in the SECTION_SIZE (if you want to hotplug smaller areas of memory), an increase in the physical address space, or an increase in the number of used page->flags. One thing to note is that, once sparsemem is present, the NUMA node information no longer needs to be stored in the page->flags. It might provide speed increases on certain platforms and will be stored there if there is room. But, if out of room, an alternate (theoretically slower) mechanism is used. This patch introduces CONFIG_FLATMEM. It is used in almost all cases where there used to be an #ifndef DISCONTIG, because SPARSEMEM and DISCONTIGMEM often have to compile out the same areas of code. Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Dave Hansen <haveblue@us.ibm.com> Signed-off-by: Martin Bligh <mbligh@aracnet.com> Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com> Signed-off-by: Bob Picco <bob.picco@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 14:07:54 +07:00
#ifdef CONFIG_FLAT_NODE_MEM_MAP
2005-06-23 14:07:37 +07:00
#define pgdat_page_nr(pgdat, pagenr) ((pgdat)->node_mem_map + (pagenr))
[PATCH] sparsemem memory model Sparsemem abstracts the use of discontiguous mem_maps[]. This kind of mem_map[] is needed by discontiguous memory machines (like in the old CONFIG_DISCONTIGMEM case) as well as memory hotplug systems. Sparsemem replaces DISCONTIGMEM when enabled, and it is hoped that it can eventually become a complete replacement. A significant advantage over DISCONTIGMEM is that it's completely separated from CONFIG_NUMA. When producing this patch, it became apparent in that NUMA and DISCONTIG are often confused. Another advantage is that sparse doesn't require each NUMA node's ranges to be contiguous. It can handle overlapping ranges between nodes with no problems, where DISCONTIGMEM currently throws away that memory. Sparsemem uses an array to provide different pfn_to_page() translations for each SECTION_SIZE area of physical memory. This is what allows the mem_map[] to be chopped up. In order to do quick pfn_to_page() operations, the section number of the page is encoded in page->flags. Part of the sparsemem infrastructure enables sharing of these bits more dynamically (at compile-time) between the page_zone() and sparsemem operations. However, on 32-bit architectures, the number of bits is quite limited, and may require growing the size of the page->flags type in certain conditions. Several things might force this to occur: a decrease in the SECTION_SIZE (if you want to hotplug smaller areas of memory), an increase in the physical address space, or an increase in the number of used page->flags. One thing to note is that, once sparsemem is present, the NUMA node information no longer needs to be stored in the page->flags. It might provide speed increases on certain platforms and will be stored there if there is room. But, if out of room, an alternate (theoretically slower) mechanism is used. This patch introduces CONFIG_FLATMEM. It is used in almost all cases where there used to be an #ifndef DISCONTIG, because SPARSEMEM and DISCONTIGMEM often have to compile out the same areas of code. Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Dave Hansen <haveblue@us.ibm.com> Signed-off-by: Martin Bligh <mbligh@aracnet.com> Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com> Signed-off-by: Bob Picco <bob.picco@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 14:07:54 +07:00
#else
#define pgdat_page_nr(pgdat, pagenr) pfn_to_page((pgdat)->node_start_pfn + (pagenr))
#endif
2005-06-23 14:07:37 +07:00
#define nid_page_nr(nid, pagenr) pgdat_page_nr(NODE_DATA(nid),(pagenr))
Fix node_start/end_pfn() definition for mm/page_cgroup.c commit 21a3c96 uses node_start/end_pfn(nid) for detection start/end of nodes. But, it's not defined in linux/mmzone.h but defined in /arch/???/include/mmzone.h which is included only under CONFIG_NEED_MULTIPLE_NODES=y. Then, we see mm/page_cgroup.c: In function 'page_cgroup_init': mm/page_cgroup.c:308: error: implicit declaration of function 'node_start_pfn' mm/page_cgroup.c:309: error: implicit declaration of function 'node_end_pfn' So, fixiing page_cgroup.c is an idea... But node_start_pfn()/node_end_pfn() is a very generic macro and should be implemented in the same manner for all archs. (m32r has different implementation...) This patch removes definitions of node_start/end_pfn() in each archs and defines a unified one in linux/mmzone.h. It's not under CONFIG_NEED_MULTIPLE_NODES, now. A result of macro expansion is here (mm/page_cgroup.c) for !NUMA start_pfn = ((&contig_page_data)->node_start_pfn); end_pfn = ({ pg_data_t *__pgdat = (&contig_page_data); __pgdat->node_start_pfn + __pgdat->node_spanned_pages;}); for NUMA (x86-64) start_pfn = ((node_data[nid])->node_start_pfn); end_pfn = ({ pg_data_t *__pgdat = (node_data[nid]); __pgdat->node_start_pfn + __pgdat->node_spanned_pages;}); Changelog: - fixed to avoid using "nid" twice in node_end_pfn() macro. Reported-and-acked-by: Randy Dunlap <randy.dunlap@oracle.com> Reported-and-tested-by: Ingo Molnar <mingo@elte.hu> Acked-by: Mel Gorman <mgorman@suse.de> Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-06-16 15:28:07 +07:00
#define node_start_pfn(nid) (NODE_DATA(nid)->node_start_pfn)
#define node_end_pfn(nid) pgdat_end_pfn(NODE_DATA(nid))
Fix node_start/end_pfn() definition for mm/page_cgroup.c commit 21a3c96 uses node_start/end_pfn(nid) for detection start/end of nodes. But, it's not defined in linux/mmzone.h but defined in /arch/???/include/mmzone.h which is included only under CONFIG_NEED_MULTIPLE_NODES=y. Then, we see mm/page_cgroup.c: In function 'page_cgroup_init': mm/page_cgroup.c:308: error: implicit declaration of function 'node_start_pfn' mm/page_cgroup.c:309: error: implicit declaration of function 'node_end_pfn' So, fixiing page_cgroup.c is an idea... But node_start_pfn()/node_end_pfn() is a very generic macro and should be implemented in the same manner for all archs. (m32r has different implementation...) This patch removes definitions of node_start/end_pfn() in each archs and defines a unified one in linux/mmzone.h. It's not under CONFIG_NEED_MULTIPLE_NODES, now. A result of macro expansion is here (mm/page_cgroup.c) for !NUMA start_pfn = ((&contig_page_data)->node_start_pfn); end_pfn = ({ pg_data_t *__pgdat = (&contig_page_data); __pgdat->node_start_pfn + __pgdat->node_spanned_pages;}); for NUMA (x86-64) start_pfn = ((node_data[nid])->node_start_pfn); end_pfn = ({ pg_data_t *__pgdat = (node_data[nid]); __pgdat->node_start_pfn + __pgdat->node_spanned_pages;}); Changelog: - fixed to avoid using "nid" twice in node_end_pfn() macro. Reported-and-acked-by: Randy Dunlap <randy.dunlap@oracle.com> Reported-and-tested-by: Ingo Molnar <mingo@elte.hu> Acked-by: Mel Gorman <mgorman@suse.de> Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-06-16 15:28:07 +07:00
static inline unsigned long pgdat_end_pfn(pg_data_t *pgdat)
{
return pgdat->node_start_pfn + pgdat->node_spanned_pages;
}
static inline bool pgdat_is_empty(pg_data_t *pgdat)
{
return !pgdat->node_start_pfn && !pgdat->node_spanned_pages;
}
Fix node_start/end_pfn() definition for mm/page_cgroup.c commit 21a3c96 uses node_start/end_pfn(nid) for detection start/end of nodes. But, it's not defined in linux/mmzone.h but defined in /arch/???/include/mmzone.h which is included only under CONFIG_NEED_MULTIPLE_NODES=y. Then, we see mm/page_cgroup.c: In function 'page_cgroup_init': mm/page_cgroup.c:308: error: implicit declaration of function 'node_start_pfn' mm/page_cgroup.c:309: error: implicit declaration of function 'node_end_pfn' So, fixiing page_cgroup.c is an idea... But node_start_pfn()/node_end_pfn() is a very generic macro and should be implemented in the same manner for all archs. (m32r has different implementation...) This patch removes definitions of node_start/end_pfn() in each archs and defines a unified one in linux/mmzone.h. It's not under CONFIG_NEED_MULTIPLE_NODES, now. A result of macro expansion is here (mm/page_cgroup.c) for !NUMA start_pfn = ((&contig_page_data)->node_start_pfn); end_pfn = ({ pg_data_t *__pgdat = (&contig_page_data); __pgdat->node_start_pfn + __pgdat->node_spanned_pages;}); for NUMA (x86-64) start_pfn = ((node_data[nid])->node_start_pfn); end_pfn = ({ pg_data_t *__pgdat = (node_data[nid]); __pgdat->node_start_pfn + __pgdat->node_spanned_pages;}); Changelog: - fixed to avoid using "nid" twice in node_end_pfn() macro. Reported-and-acked-by: Randy Dunlap <randy.dunlap@oracle.com> Reported-and-tested-by: Ingo Molnar <mingo@elte.hu> Acked-by: Mel Gorman <mgorman@suse.de> Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-06-16 15:28:07 +07:00
#include <linux/memory_hotplug.h>
extern struct mutex zonelists_mutex;
mm/hotplug: correctly setup fallback zonelists when creating new pgdat When hotadd_new_pgdat() is called to create new pgdat for a new node, a fallback zonelist should be created for the new node. There's code to try to achieve that in hotadd_new_pgdat() as below: /* * The node we allocated has no zone fallback lists. For avoiding * to access not-initialized zonelist, build here. */ mutex_lock(&zonelists_mutex); build_all_zonelists(pgdat, NULL); mutex_unlock(&zonelists_mutex); But it doesn't work as expected. When hotadd_new_pgdat() is called, the new node is still in offline state because node_set_online(nid) hasn't been called yet. And build_all_zonelists() only builds zonelists for online nodes as: for_each_online_node(nid) { pg_data_t *pgdat = NODE_DATA(nid); build_zonelists(pgdat); build_zonelist_cache(pgdat); } Though we hope to create zonelist for the new pgdat, but it doesn't. So add a new parameter "pgdat" the build_all_zonelists() to build pgdat for the new pgdat too. Signed-off-by: Jiang Liu <liuj97@gmail.com> Signed-off-by: Xishi Qiu <qiuxishi@huawei.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Michal Hocko <mhocko@suse.cz> Cc: Minchan Kim <minchan@kernel.org> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Yinghai Lu <yinghai@kernel.org> Cc: Tony Luck <tony.luck@intel.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: David Rientjes <rientjes@google.com> Cc: Keping Chen <chenkeping@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-08-01 06:43:28 +07:00
void build_all_zonelists(pg_data_t *pgdat, struct zone *zone);
mm: kswapd: stop high-order balancing when any suitable zone is balanced Simon Kirby reported the following problem We're seeing cases on a number of servers where cache never fully grows to use all available memory. Sometimes we see servers with 4 GB of memory that never seem to have less than 1.5 GB free, even with a constantly-active VM. In some cases, these servers also swap out while this happens, even though they are constantly reading the working set into memory. We have been seeing this happening for a long time; I don't think it's anything recent, and it still happens on 2.6.36. After some debugging work by Simon, Dave Hansen and others, the prevaling theory became that kswapd is reclaiming order-3 pages requested by SLUB too aggressive about it. There are two apparent problems here. On the target machine, there is a small Normal zone in comparison to DMA32. As kswapd tries to balance all zones, it would continually try reclaiming for Normal even though DMA32 was balanced enough for callers. The second problem is that sleeping_prematurely() does not use the same logic as balance_pgdat() when deciding whether to sleep or not. This keeps kswapd artifically awake. A number of tests were run and the figures from previous postings will look very different for a few reasons. One, the old figures were forcing my network card to use GFP_ATOMIC in attempt to replicate Simon's problem. Second, I previous specified slub_min_order=3 again in an attempt to reproduce Simon's problem. In this posting, I'm depending on Simon to say whether his problem is fixed or not and these figures are to show the impact to the ordinary cases. Finally, the "vmscan" figures are taken from /proc/vmstat instead of the tracepoints. There is less information but recording is less disruptive. The first test of relevance was postmark with a process running in the background reading a large amount of anonymous memory in blocks. The objective was to vaguely simulate what was happening on Simon's machine and it's memory intensive enough to have kswapd awake. POSTMARK traceonly kanyzone Transactions per second: 156.00 ( 0.00%) 153.00 (-1.96%) Data megabytes read per second: 21.51 ( 0.00%) 21.52 ( 0.05%) Data megabytes written per second: 29.28 ( 0.00%) 29.11 (-0.58%) Files created alone per second: 250.00 ( 0.00%) 416.00 (39.90%) Files create/transact per second: 79.00 ( 0.00%) 76.00 (-3.95%) Files deleted alone per second: 520.00 ( 0.00%) 420.00 (-23.81%) Files delete/transact per second: 79.00 ( 0.00%) 76.00 (-3.95%) MMTests Statistics: duration User/Sys Time Running Test (seconds) 16.58 17.4 Total Elapsed Time (seconds) 218.48 222.47 VMstat Reclaim Statistics: vmscan Direct reclaims 0 4 Direct reclaim pages scanned 0 203 Direct reclaim pages reclaimed 0 184 Kswapd pages scanned 326631 322018 Kswapd pages reclaimed 312632 309784 Kswapd low wmark quickly 1 4 Kswapd high wmark quickly 122 475 Kswapd skip congestion_wait 1 0 Pages activated 700040 705317 Pages deactivated 212113 203922 Pages written 9875 6363 Total pages scanned 326631 322221 Total pages reclaimed 312632 309968 %age total pages scanned/reclaimed 95.71% 96.20% %age total pages scanned/written 3.02% 1.97% proc vmstat: Faults Major Faults 300 254 Minor Faults 645183 660284 Page ins 493588 486704 Page outs 4960088 4986704 Swap ins 1230 661 Swap outs 9869 6355 Performance is mildly affected because kswapd is no longer doing as much work and the background memory consumer process is getting in the way. Note that kswapd scanned and reclaimed fewer pages as it's less aggressive and overall fewer pages were scanned and reclaimed. Swap in/out is particularly reduced again reflecting kswapd throwing out fewer pages. The slight performance impact is unfortunate here but it looks like a direct result of kswapd being less aggressive. As the bug report is about too many pages being freed by kswapd, it may have to be accepted for now. The second test is a streaming IO benchmark that was previously used by Johannes to show regressions in page reclaim. MICRO traceonly kanyzone User/Sys Time Running Test (seconds) 29.29 28.87 Total Elapsed Time (seconds) 492.18 488.79 VMstat Reclaim Statistics: vmscan Direct reclaims 2128 1460 Direct reclaim pages scanned 2284822 1496067 Direct reclaim pages reclaimed 148919 110937 Kswapd pages scanned 15450014 16202876 Kswapd pages reclaimed 8503697 8537897 Kswapd low wmark quickly 3100 3397 Kswapd high wmark quickly 1860 7243 Kswapd skip congestion_wait 708 801 Pages activated 9635 9573 Pages deactivated 1432 1271 Pages written 223 1130 Total pages scanned 17734836 17698943 Total pages reclaimed 8652616 8648834 %age total pages scanned/reclaimed 48.79% 48.87% %age total pages scanned/written 0.00% 0.01% proc vmstat: Faults Major Faults 165 221 Minor Faults 9655785 9656506 Page ins 3880 7228 Page outs 37692940 37480076 Swap ins 0 69 Swap outs 19 15 Again fewer pages are scanned and reclaimed as expected and this time the test completed faster. Note that kswapd is hitting its watermarks faster (low and high wmark quickly) which I expect is due to kswapd reclaiming fewer pages. I also ran fs-mark, iozone and sysbench but there is nothing interesting to report in the figures. Performance is not significantly changed and the reclaim statistics look reasonable. Tgis patch: When the allocator enters its slow path, kswapd is woken up to balance the node. It continues working until all zones within the node are balanced. For order-0 allocations, this makes perfect sense but for higher orders it can have unintended side-effects. If the zone sizes are imbalanced, kswapd may reclaim heavily within a smaller zone discarding an excessive number of pages. The user-visible behaviour is that kswapd is awake and reclaiming even though plenty of pages are free from a suitable zone. This patch alters the "balance" logic for high-order reclaim allowing kswapd to stop if any suitable zone becomes balanced to reduce the number of pages it reclaims from other zones. kswapd still tries to ensure that order-0 watermarks for all zones are met before sleeping. Signed-off-by: Mel Gorman <mel@csn.ul.ie> Reviewed-by: Minchan Kim <minchan.kim@gmail.com> Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Reviewed-by: Eric B Munson <emunson@mgebm.net> Cc: Simon Kirby <sim@hostway.ca> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Shaohua Li <shaohua.li@intel.com> Cc: Dave Hansen <dave@linux.vnet.ibm.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Rik van Riel <riel@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-01-14 06:46:20 +07:00
void wakeup_kswapd(struct zone *zone, int order, enum zone_type classzone_idx);
bool zone_watermark_ok(struct zone *z, unsigned int order,
unsigned long mark, int classzone_idx, int alloc_flags);
bool zone_watermark_ok_safe(struct zone *z, unsigned int order,
unsigned long mark, int classzone_idx, int alloc_flags);
enum memmap_context {
MEMMAP_EARLY,
MEMMAP_HOTPLUG,
};
extern int init_currently_empty_zone(struct zone *zone, unsigned long start_pfn,
unsigned long size,
enum memmap_context context);
memcg: fix hotplugged memory zone oops When MEMCG is configured on (even when it's disabled by boot option), when adding or removing a page to/from its lru list, the zone pointer used for stats updates is nowadays taken from the struct lruvec. (On many configurations, calculating zone from page is slower.) But we have no code to update all the lruvecs (per zone, per memcg) when a memory node is hotadded. Here's an extract from the oops which results when running numactl to bind a program to a newly onlined node: BUG: unable to handle kernel NULL pointer dereference at 0000000000000f60 IP: __mod_zone_page_state+0x9/0x60 Pid: 1219, comm: numactl Not tainted 3.6.0-rc5+ #180 Bochs Bochs Process numactl (pid: 1219, threadinfo ffff880039abc000, task ffff8800383c4ce0) Call Trace: __pagevec_lru_add_fn+0xdf/0x140 pagevec_lru_move_fn+0xb1/0x100 __pagevec_lru_add+0x1c/0x30 lru_add_drain_cpu+0xa3/0x130 lru_add_drain+0x2f/0x40 ... The natural solution might be to use a memcg callback whenever memory is hotadded; but that solution has not been scoped out, and it happens that we do have an easy location at which to update lruvec->zone. The lruvec pointer is discovered either by mem_cgroup_zone_lruvec() or by mem_cgroup_page_lruvec(), and both of those do know the right zone. So check and set lruvec->zone in those; and remove the inadequate attempt to set lruvec->zone from lruvec_init(), which is called before NODE_DATA(node) has been allocated in such cases. Ah, there was one exceptionr. For no particularly good reason, mem_cgroup_force_empty_list() has its own code for deciding lruvec. Change it to use the standard mem_cgroup_zone_lruvec() and mem_cgroup_get_lru_size() too. In fact it was already safe against such an oops (the lru lists in danger could only be empty), but we're better proofed against future changes this way. I've marked this for stable (3.6) since we introduced the problem in 3.5 (now closed to stable); but I have no idea if this is the only fix needed to get memory hotadd working with memcg in 3.6, and received no answer when I enquired twice before. Reported-by: Tang Chen <tangchen@cn.fujitsu.com> Signed-off-by: Hugh Dickins <hughd@google.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Konstantin Khlebnikov <khlebnikov@openvz.org> Cc: Wen Congyang <wency@cn.fujitsu.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-11-17 05:14:54 +07:00
extern void lruvec_init(struct lruvec *lruvec);
static inline struct zone *lruvec_zone(struct lruvec *lruvec)
{
#ifdef CONFIG_MEMCG
return lruvec->zone;
#else
return container_of(lruvec, struct zone, lruvec);
#endif
}
#ifdef CONFIG_HAVE_MEMORY_PRESENT
void memory_present(int nid, unsigned long start, unsigned long end);
#else
static inline void memory_present(int nid, unsigned long start, unsigned long end) {}
#endif
numa: introduce numa_mem_id()- effective local memory node id Introduce numa_mem_id(), based on generic percpu variable infrastructure to track "nearest node with memory" for archs that support memoryless nodes. Define API in <linux/topology.h> when CONFIG_HAVE_MEMORYLESS_NODES defined, else stubs. Architectures will define HAVE_MEMORYLESS_NODES if/when they support them. Archs can override definitions of: numa_mem_id() - returns node number of "local memory" node set_numa_mem() - initialize [this cpus'] per cpu variable 'numa_mem' cpu_to_mem() - return numa_mem for specified cpu; may be used as lvalue Generic initialization of 'numa_mem' occurs in __build_all_zonelists(). This will initialize the boot cpu at boot time, and all cpus on change of numa_zonelist_order, or when node or memory hot-plug requires zonelist rebuild. Archs that support memoryless nodes will need to initialize 'numa_mem' for secondary cpus as they're brought on-line. [akpm@linux-foundation.org: fix build] Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com> Signed-off-by: Christoph Lameter <cl@linux-foundation.org> Cc: Tejun Heo <tj@kernel.org> Cc: Mel Gorman <mel@csn.ul.ie> Cc: Christoph Lameter <cl@linux-foundation.org> Cc: Nick Piggin <npiggin@suse.de> Cc: David Rientjes <rientjes@google.com> Cc: Eric Whitney <eric.whitney@hp.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: "Luck, Tony" <tony.luck@intel.com> Cc: Pekka Enberg <penberg@cs.helsinki.fi> Cc: <linux-arch@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-05-27 04:45:00 +07:00
#ifdef CONFIG_HAVE_MEMORYLESS_NODES
int local_memory_node(int node_id);
#else
static inline int local_memory_node(int node_id) { return node_id; };
#endif
#ifdef CONFIG_NEED_NODE_MEMMAP_SIZE
unsigned long __init node_memmap_size_bytes(int, unsigned long, unsigned long);
#endif
/*
* zone_idx() returns 0 for the ZONE_DMA zone, 1 for the ZONE_NORMAL zone, etc.
*/
#define zone_idx(zone) ((zone) - (zone)->zone_pgdat->node_zones)
static inline int populated_zone(struct zone *zone)
{
return (!!zone->present_pages);
}
Create the ZONE_MOVABLE zone The following 8 patches against 2.6.20-mm2 create a zone called ZONE_MOVABLE that is only usable by allocations that specify both __GFP_HIGHMEM and __GFP_MOVABLE. This has the effect of keeping all non-movable pages within a single memory partition while allowing movable allocations to be satisfied from either partition. The patches may be applied with the list-based anti-fragmentation patches that groups pages together based on mobility. The size of the zone is determined by a kernelcore= parameter specified at boot-time. This specifies how much memory is usable by non-movable allocations and the remainder is used for ZONE_MOVABLE. Any range of pages within ZONE_MOVABLE can be released by migrating the pages or by reclaiming. When selecting a zone to take pages from for ZONE_MOVABLE, there are two things to consider. First, only memory from the highest populated zone is used for ZONE_MOVABLE. On the x86, this is probably going to be ZONE_HIGHMEM but it would be ZONE_DMA on ppc64 or possibly ZONE_DMA32 on x86_64. Second, the amount of memory usable by the kernel will be spread evenly throughout NUMA nodes where possible. If the nodes are not of equal size, the amount of memory usable by the kernel on some nodes may be greater than others. By default, the zone is not as useful for hugetlb allocations because they are pinned and non-migratable (currently at least). A sysctl is provided that allows huge pages to be allocated from that zone. This means that the huge page pool can be resized to the size of ZONE_MOVABLE during the lifetime of the system assuming that pages are not mlocked. Despite huge pages being non-movable, we do not introduce additional external fragmentation of note as huge pages are always the largest contiguous block we care about. Credit goes to Andy Whitcroft for catching a large variety of problems during review of the patches. This patch creates an additional zone, ZONE_MOVABLE. This zone is only usable by allocations which specify both __GFP_HIGHMEM and __GFP_MOVABLE. Hot-added memory continues to be placed in their existing destination as there is no mechanism to redirect them to a specific zone. [y-goto@jp.fujitsu.com: Fix section mismatch of memory hotplug related code] [akpm@linux-foundation.org: various fixes] Signed-off-by: Mel Gorman <mel@csn.ul.ie> Cc: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com> Cc: William Lee Irwin III <wli@holomorphy.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-17 18:03:12 +07:00
extern int movable_zone;
#ifdef CONFIG_HIGHMEM
Create the ZONE_MOVABLE zone The following 8 patches against 2.6.20-mm2 create a zone called ZONE_MOVABLE that is only usable by allocations that specify both __GFP_HIGHMEM and __GFP_MOVABLE. This has the effect of keeping all non-movable pages within a single memory partition while allowing movable allocations to be satisfied from either partition. The patches may be applied with the list-based anti-fragmentation patches that groups pages together based on mobility. The size of the zone is determined by a kernelcore= parameter specified at boot-time. This specifies how much memory is usable by non-movable allocations and the remainder is used for ZONE_MOVABLE. Any range of pages within ZONE_MOVABLE can be released by migrating the pages or by reclaiming. When selecting a zone to take pages from for ZONE_MOVABLE, there are two things to consider. First, only memory from the highest populated zone is used for ZONE_MOVABLE. On the x86, this is probably going to be ZONE_HIGHMEM but it would be ZONE_DMA on ppc64 or possibly ZONE_DMA32 on x86_64. Second, the amount of memory usable by the kernel will be spread evenly throughout NUMA nodes where possible. If the nodes are not of equal size, the amount of memory usable by the kernel on some nodes may be greater than others. By default, the zone is not as useful for hugetlb allocations because they are pinned and non-migratable (currently at least). A sysctl is provided that allows huge pages to be allocated from that zone. This means that the huge page pool can be resized to the size of ZONE_MOVABLE during the lifetime of the system assuming that pages are not mlocked. Despite huge pages being non-movable, we do not introduce additional external fragmentation of note as huge pages are always the largest contiguous block we care about. Credit goes to Andy Whitcroft for catching a large variety of problems during review of the patches. This patch creates an additional zone, ZONE_MOVABLE. This zone is only usable by allocations which specify both __GFP_HIGHMEM and __GFP_MOVABLE. Hot-added memory continues to be placed in their existing destination as there is no mechanism to redirect them to a specific zone. [y-goto@jp.fujitsu.com: Fix section mismatch of memory hotplug related code] [akpm@linux-foundation.org: various fixes] Signed-off-by: Mel Gorman <mel@csn.ul.ie> Cc: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com> Cc: William Lee Irwin III <wli@holomorphy.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-17 18:03:12 +07:00
static inline int zone_movable_is_highmem(void)
{
#ifdef CONFIG_HAVE_MEMBLOCK_NODE_MAP
Create the ZONE_MOVABLE zone The following 8 patches against 2.6.20-mm2 create a zone called ZONE_MOVABLE that is only usable by allocations that specify both __GFP_HIGHMEM and __GFP_MOVABLE. This has the effect of keeping all non-movable pages within a single memory partition while allowing movable allocations to be satisfied from either partition. The patches may be applied with the list-based anti-fragmentation patches that groups pages together based on mobility. The size of the zone is determined by a kernelcore= parameter specified at boot-time. This specifies how much memory is usable by non-movable allocations and the remainder is used for ZONE_MOVABLE. Any range of pages within ZONE_MOVABLE can be released by migrating the pages or by reclaiming. When selecting a zone to take pages from for ZONE_MOVABLE, there are two things to consider. First, only memory from the highest populated zone is used for ZONE_MOVABLE. On the x86, this is probably going to be ZONE_HIGHMEM but it would be ZONE_DMA on ppc64 or possibly ZONE_DMA32 on x86_64. Second, the amount of memory usable by the kernel will be spread evenly throughout NUMA nodes where possible. If the nodes are not of equal size, the amount of memory usable by the kernel on some nodes may be greater than others. By default, the zone is not as useful for hugetlb allocations because they are pinned and non-migratable (currently at least). A sysctl is provided that allows huge pages to be allocated from that zone. This means that the huge page pool can be resized to the size of ZONE_MOVABLE during the lifetime of the system assuming that pages are not mlocked. Despite huge pages being non-movable, we do not introduce additional external fragmentation of note as huge pages are always the largest contiguous block we care about. Credit goes to Andy Whitcroft for catching a large variety of problems during review of the patches. This patch creates an additional zone, ZONE_MOVABLE. This zone is only usable by allocations which specify both __GFP_HIGHMEM and __GFP_MOVABLE. Hot-added memory continues to be placed in their existing destination as there is no mechanism to redirect them to a specific zone. [y-goto@jp.fujitsu.com: Fix section mismatch of memory hotplug related code] [akpm@linux-foundation.org: various fixes] Signed-off-by: Mel Gorman <mel@csn.ul.ie> Cc: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com> Cc: William Lee Irwin III <wli@holomorphy.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-17 18:03:12 +07:00
return movable_zone == ZONE_HIGHMEM;
#else
return (ZONE_MOVABLE - 1) == ZONE_HIGHMEM;
Create the ZONE_MOVABLE zone The following 8 patches against 2.6.20-mm2 create a zone called ZONE_MOVABLE that is only usable by allocations that specify both __GFP_HIGHMEM and __GFP_MOVABLE. This has the effect of keeping all non-movable pages within a single memory partition while allowing movable allocations to be satisfied from either partition. The patches may be applied with the list-based anti-fragmentation patches that groups pages together based on mobility. The size of the zone is determined by a kernelcore= parameter specified at boot-time. This specifies how much memory is usable by non-movable allocations and the remainder is used for ZONE_MOVABLE. Any range of pages within ZONE_MOVABLE can be released by migrating the pages or by reclaiming. When selecting a zone to take pages from for ZONE_MOVABLE, there are two things to consider. First, only memory from the highest populated zone is used for ZONE_MOVABLE. On the x86, this is probably going to be ZONE_HIGHMEM but it would be ZONE_DMA on ppc64 or possibly ZONE_DMA32 on x86_64. Second, the amount of memory usable by the kernel will be spread evenly throughout NUMA nodes where possible. If the nodes are not of equal size, the amount of memory usable by the kernel on some nodes may be greater than others. By default, the zone is not as useful for hugetlb allocations because they are pinned and non-migratable (currently at least). A sysctl is provided that allows huge pages to be allocated from that zone. This means that the huge page pool can be resized to the size of ZONE_MOVABLE during the lifetime of the system assuming that pages are not mlocked. Despite huge pages being non-movable, we do not introduce additional external fragmentation of note as huge pages are always the largest contiguous block we care about. Credit goes to Andy Whitcroft for catching a large variety of problems during review of the patches. This patch creates an additional zone, ZONE_MOVABLE. This zone is only usable by allocations which specify both __GFP_HIGHMEM and __GFP_MOVABLE. Hot-added memory continues to be placed in their existing destination as there is no mechanism to redirect them to a specific zone. [y-goto@jp.fujitsu.com: Fix section mismatch of memory hotplug related code] [akpm@linux-foundation.org: various fixes] Signed-off-by: Mel Gorman <mel@csn.ul.ie> Cc: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com> Cc: William Lee Irwin III <wli@holomorphy.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-17 18:03:12 +07:00
#endif
}
#endif
Create the ZONE_MOVABLE zone The following 8 patches against 2.6.20-mm2 create a zone called ZONE_MOVABLE that is only usable by allocations that specify both __GFP_HIGHMEM and __GFP_MOVABLE. This has the effect of keeping all non-movable pages within a single memory partition while allowing movable allocations to be satisfied from either partition. The patches may be applied with the list-based anti-fragmentation patches that groups pages together based on mobility. The size of the zone is determined by a kernelcore= parameter specified at boot-time. This specifies how much memory is usable by non-movable allocations and the remainder is used for ZONE_MOVABLE. Any range of pages within ZONE_MOVABLE can be released by migrating the pages or by reclaiming. When selecting a zone to take pages from for ZONE_MOVABLE, there are two things to consider. First, only memory from the highest populated zone is used for ZONE_MOVABLE. On the x86, this is probably going to be ZONE_HIGHMEM but it would be ZONE_DMA on ppc64 or possibly ZONE_DMA32 on x86_64. Second, the amount of memory usable by the kernel will be spread evenly throughout NUMA nodes where possible. If the nodes are not of equal size, the amount of memory usable by the kernel on some nodes may be greater than others. By default, the zone is not as useful for hugetlb allocations because they are pinned and non-migratable (currently at least). A sysctl is provided that allows huge pages to be allocated from that zone. This means that the huge page pool can be resized to the size of ZONE_MOVABLE during the lifetime of the system assuming that pages are not mlocked. Despite huge pages being non-movable, we do not introduce additional external fragmentation of note as huge pages are always the largest contiguous block we care about. Credit goes to Andy Whitcroft for catching a large variety of problems during review of the patches. This patch creates an additional zone, ZONE_MOVABLE. This zone is only usable by allocations which specify both __GFP_HIGHMEM and __GFP_MOVABLE. Hot-added memory continues to be placed in their existing destination as there is no mechanism to redirect them to a specific zone. [y-goto@jp.fujitsu.com: Fix section mismatch of memory hotplug related code] [akpm@linux-foundation.org: various fixes] Signed-off-by: Mel Gorman <mel@csn.ul.ie> Cc: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com> Cc: William Lee Irwin III <wli@holomorphy.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-17 18:03:12 +07:00
static inline int is_highmem_idx(enum zone_type idx)
{
#ifdef CONFIG_HIGHMEM
Create the ZONE_MOVABLE zone The following 8 patches against 2.6.20-mm2 create a zone called ZONE_MOVABLE that is only usable by allocations that specify both __GFP_HIGHMEM and __GFP_MOVABLE. This has the effect of keeping all non-movable pages within a single memory partition while allowing movable allocations to be satisfied from either partition. The patches may be applied with the list-based anti-fragmentation patches that groups pages together based on mobility. The size of the zone is determined by a kernelcore= parameter specified at boot-time. This specifies how much memory is usable by non-movable allocations and the remainder is used for ZONE_MOVABLE. Any range of pages within ZONE_MOVABLE can be released by migrating the pages or by reclaiming. When selecting a zone to take pages from for ZONE_MOVABLE, there are two things to consider. First, only memory from the highest populated zone is used for ZONE_MOVABLE. On the x86, this is probably going to be ZONE_HIGHMEM but it would be ZONE_DMA on ppc64 or possibly ZONE_DMA32 on x86_64. Second, the amount of memory usable by the kernel will be spread evenly throughout NUMA nodes where possible. If the nodes are not of equal size, the amount of memory usable by the kernel on some nodes may be greater than others. By default, the zone is not as useful for hugetlb allocations because they are pinned and non-migratable (currently at least). A sysctl is provided that allows huge pages to be allocated from that zone. This means that the huge page pool can be resized to the size of ZONE_MOVABLE during the lifetime of the system assuming that pages are not mlocked. Despite huge pages being non-movable, we do not introduce additional external fragmentation of note as huge pages are always the largest contiguous block we care about. Credit goes to Andy Whitcroft for catching a large variety of problems during review of the patches. This patch creates an additional zone, ZONE_MOVABLE. This zone is only usable by allocations which specify both __GFP_HIGHMEM and __GFP_MOVABLE. Hot-added memory continues to be placed in their existing destination as there is no mechanism to redirect them to a specific zone. [y-goto@jp.fujitsu.com: Fix section mismatch of memory hotplug related code] [akpm@linux-foundation.org: various fixes] Signed-off-by: Mel Gorman <mel@csn.ul.ie> Cc: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com> Cc: William Lee Irwin III <wli@holomorphy.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-17 18:03:12 +07:00
return (idx == ZONE_HIGHMEM ||
(idx == ZONE_MOVABLE && zone_movable_is_highmem()));
#else
return 0;
#endif
}
/**
* is_highmem - helper function to quickly check if a struct zone is a
* highmem zone or not. This is an attempt to keep references
* to ZONE_{DMA/NORMAL/HIGHMEM/etc} in general code to a minimum.
* @zone - pointer to struct zone variable
*/
static inline int is_highmem(struct zone *zone)
{
#ifdef CONFIG_HIGHMEM
int zone_off = (char *)zone - (char *)zone->zone_pgdat->node_zones;
return zone_off == ZONE_HIGHMEM * sizeof(*zone) ||
(zone_off == ZONE_MOVABLE * sizeof(*zone) &&
zone_movable_is_highmem());
#else
return 0;
#endif
}
/* These two functions are used to setup the per zone pages min values */
struct ctl_table;
int min_free_kbytes_sysctl_handler(struct ctl_table *, int,
void __user *, size_t *, loff_t *);
extern int sysctl_lowmem_reserve_ratio[MAX_NR_ZONES-1];
int lowmem_reserve_ratio_sysctl_handler(struct ctl_table *, int,
void __user *, size_t *, loff_t *);
int percpu_pagelist_fraction_sysctl_handler(struct ctl_table *, int,
void __user *, size_t *, loff_t *);
int sysctl_min_unmapped_ratio_sysctl_handler(struct ctl_table *, int,
void __user *, size_t *, loff_t *);
[PATCH] zone_reclaim: dynamic slab reclaim Currently one can enable slab reclaim by setting an explicit option in /proc/sys/vm/zone_reclaim_mode. Slab reclaim is then used as a final option if the freeing of unmapped file backed pages is not enough to free enough pages to allow a local allocation. However, that means that the slab can grow excessively and that most memory of a node may be used by slabs. We have had a case where a machine with 46GB of memory was using 40-42GB for slab. Zone reclaim was effective in dealing with pagecache pages. However, slab reclaim was only done during global reclaim (which is a bit rare on NUMA systems). This patch implements slab reclaim during zone reclaim. Zone reclaim occurs if there is a danger of an off node allocation. At that point we 1. Shrink the per node page cache if the number of pagecache pages is more than min_unmapped_ratio percent of pages in a zone. 2. Shrink the slab cache if the number of the nodes reclaimable slab pages (patch depends on earlier one that implements that counter) are more than min_slab_ratio (a new /proc/sys/vm tunable). The shrinking of the slab cache is a bit problematic since it is not node specific. So we simply calculate what point in the slab we want to reach (current per node slab use minus the number of pages that neeed to be allocated) and then repeately run the global reclaim until that is unsuccessful or we have reached the limit. I hope we will have zone based slab reclaim at some point which will make that easier. The default for the min_slab_ratio is 5% Also remove the slab option from /proc/sys/vm/zone_reclaim_mode. [akpm@osdl.org: cleanups] Signed-off-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-09-26 13:31:52 +07:00
int sysctl_min_slab_ratio_sysctl_handler(struct ctl_table *, int,
void __user *, size_t *, loff_t *);
change zonelist order: zonelist order selection logic Make zonelist creation policy selectable from sysctl/boot option v6. This patch makes NUMA's zonelist (of pgdat) order selectable. Available order are Default(automatic)/ Node-based / Zone-based. [Default Order] The kernel selects Node-based or Zone-based order automatically. [Node-based Order] This policy treats the locality of memory as the most important parameter. Zonelist order is created by each zone's locality. This means lower zones (ex. ZONE_DMA) can be used before higher zone (ex. ZONE_NORMAL) exhausion. IOW. ZONE_DMA will be in the middle of zonelist. current 2.6.21 kernel uses this. Pros. * A user can expect local memory as much as possible. Cons. * lower zone will be exhansted before higher zone. This may cause OOM_KILL. Maybe suitable if ZONE_DMA is relatively big and you never see OOM_KILL because of ZONE_DMA exhaution and you need the best locality. (example) assume 2 node NUMA. node(0) has ZONE_DMA/ZONE_NORMAL, node(1) has ZONE_NORMAL. *node(0)'s memory allocation order: node(0)'s NORMAL -> node(0)'s DMA -> node(1)'s NORMAL. *node(1)'s memory allocation order: node(1)'s NORMAL -> node(0)'s NORMAL -> node(0)'s DMA. [Zone-based order] This policy treats the zone type as the most important parameter. Zonelist order is created by zone-type order. This means lower zone never be used bofere higher zone exhaustion. IOW. ZONE_DMA will be always at the tail of zonelist. Pros. * OOM_KILL(bacause of lower zone) occurs only if the whole zones are exhausted. Cons. * memory locality may not be best. (example) assume 2 node NUMA. node(0) has ZONE_DMA/ZONE_NORMAL, node(1) has ZONE_NORMAL. *node(0)'s memory allocation order: node(0)'s NORMAL -> node(1)'s NORMAL -> node(0)'s DMA. *node(1)'s memory allocation order: node(1)'s NORMAL -> node(0)'s NORMAL -> node(0)'s DMA. bootoption "numa_zonelist_order=" and proc/sysctl is supporetd. command: %echo N > /proc/sys/vm/numa_zonelist_order Will rebuild zonelist in Node-based order. command: %echo Z > /proc/sys/vm/numa_zonelist_order Will rebuild zonelist in Zone-based order. Thanks to Lee Schermerhorn, he gives me much help and codes. [Lee.Schermerhorn@hp.com: add check_highest_zone to build_zonelists_in_zone_order] [akpm@linux-foundation.org: build fix] Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Lee Schermerhorn <lee.schermerhorn@hp.com> Cc: Christoph Lameter <clameter@sgi.com> Cc: Andi Kleen <ak@suse.de> Cc: "jesse.barnes@intel.com" <jesse.barnes@intel.com> Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-16 13:38:01 +07:00
extern int numa_zonelist_order_handler(struct ctl_table *, int,
void __user *, size_t *, loff_t *);
change zonelist order: zonelist order selection logic Make zonelist creation policy selectable from sysctl/boot option v6. This patch makes NUMA's zonelist (of pgdat) order selectable. Available order are Default(automatic)/ Node-based / Zone-based. [Default Order] The kernel selects Node-based or Zone-based order automatically. [Node-based Order] This policy treats the locality of memory as the most important parameter. Zonelist order is created by each zone's locality. This means lower zones (ex. ZONE_DMA) can be used before higher zone (ex. ZONE_NORMAL) exhausion. IOW. ZONE_DMA will be in the middle of zonelist. current 2.6.21 kernel uses this. Pros. * A user can expect local memory as much as possible. Cons. * lower zone will be exhansted before higher zone. This may cause OOM_KILL. Maybe suitable if ZONE_DMA is relatively big and you never see OOM_KILL because of ZONE_DMA exhaution and you need the best locality. (example) assume 2 node NUMA. node(0) has ZONE_DMA/ZONE_NORMAL, node(1) has ZONE_NORMAL. *node(0)'s memory allocation order: node(0)'s NORMAL -> node(0)'s DMA -> node(1)'s NORMAL. *node(1)'s memory allocation order: node(1)'s NORMAL -> node(0)'s NORMAL -> node(0)'s DMA. [Zone-based order] This policy treats the zone type as the most important parameter. Zonelist order is created by zone-type order. This means lower zone never be used bofere higher zone exhaustion. IOW. ZONE_DMA will be always at the tail of zonelist. Pros. * OOM_KILL(bacause of lower zone) occurs only if the whole zones are exhausted. Cons. * memory locality may not be best. (example) assume 2 node NUMA. node(0) has ZONE_DMA/ZONE_NORMAL, node(1) has ZONE_NORMAL. *node(0)'s memory allocation order: node(0)'s NORMAL -> node(1)'s NORMAL -> node(0)'s DMA. *node(1)'s memory allocation order: node(1)'s NORMAL -> node(0)'s NORMAL -> node(0)'s DMA. bootoption "numa_zonelist_order=" and proc/sysctl is supporetd. command: %echo N > /proc/sys/vm/numa_zonelist_order Will rebuild zonelist in Node-based order. command: %echo Z > /proc/sys/vm/numa_zonelist_order Will rebuild zonelist in Zone-based order. Thanks to Lee Schermerhorn, he gives me much help and codes. [Lee.Schermerhorn@hp.com: add check_highest_zone to build_zonelists_in_zone_order] [akpm@linux-foundation.org: build fix] Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Lee Schermerhorn <lee.schermerhorn@hp.com> Cc: Christoph Lameter <clameter@sgi.com> Cc: Andi Kleen <ak@suse.de> Cc: "jesse.barnes@intel.com" <jesse.barnes@intel.com> Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-16 13:38:01 +07:00
extern char numa_zonelist_order[];
#define NUMA_ZONELIST_ORDER_LEN 16 /* string buffer size */
#ifndef CONFIG_NEED_MULTIPLE_NODES
extern struct pglist_data contig_page_data;
#define NODE_DATA(nid) (&contig_page_data)
#define NODE_MEM_MAP(nid) mem_map
#else /* CONFIG_NEED_MULTIPLE_NODES */
#include <asm/mmzone.h>
#endif /* !CONFIG_NEED_MULTIPLE_NODES */
extern struct pglist_data *first_online_pgdat(void);
extern struct pglist_data *next_online_pgdat(struct pglist_data *pgdat);
extern struct zone *next_zone(struct zone *zone);
/**
* for_each_online_pgdat - helper macro to iterate over all online nodes
* @pgdat - pointer to a pg_data_t variable
*/
#define for_each_online_pgdat(pgdat) \
for (pgdat = first_online_pgdat(); \
pgdat; \
pgdat = next_online_pgdat(pgdat))
/**
* for_each_zone - helper macro to iterate over all memory zones
* @zone - pointer to struct zone variable
*
* The user only needs to declare the zone variable, for_each_zone
* fills it in.
*/
#define for_each_zone(zone) \
for (zone = (first_online_pgdat())->node_zones; \
zone; \
zone = next_zone(zone))
#define for_each_populated_zone(zone) \
for (zone = (first_online_pgdat())->node_zones; \
zone; \
zone = next_zone(zone)) \
if (!populated_zone(zone)) \
; /* do nothing */ \
else
mm: have zonelist contains structs with both a zone pointer and zone_idx Filtering zonelists requires very frequent use of zone_idx(). This is costly as it involves a lookup of another structure and a substraction operation. As the zone_idx is often required, it should be quickly accessible. The node idx could also be stored here if it was found that accessing zone->node is significant which may be the case on workloads where nodemasks are heavily used. This patch introduces a struct zoneref to store a zone pointer and a zone index. The zonelist then consists of an array of these struct zonerefs which are looked up as necessary. Helpers are given for accessing the zone index as well as the node index. [kamezawa.hiroyu@jp.fujitsu.com: Suggested struct zoneref instead of embedding information in pointers] [hugh@veritas.com: mm-have-zonelist: fix memcg ooms] [hugh@veritas.com: just return do_try_to_free_pages] [hugh@veritas.com: do_try_to_free_pages gfp_mask redundant] Signed-off-by: Mel Gorman <mel@csn.ul.ie> Acked-by: Christoph Lameter <clameter@sgi.com> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Mel Gorman <mel@csn.ul.ie> Cc: Christoph Lameter <clameter@sgi.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Hugh Dickins <hugh@veritas.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 16:12:17 +07:00
static inline struct zone *zonelist_zone(struct zoneref *zoneref)
{
return zoneref->zone;
}
static inline int zonelist_zone_idx(struct zoneref *zoneref)
{
return zoneref->zone_idx;
}
static inline int zonelist_node_idx(struct zoneref *zoneref)
{
#ifdef CONFIG_NUMA
/* zone_to_nid not available in this context */
return zoneref->zone->node;
#else
return 0;
#endif /* CONFIG_NUMA */
}
/**
* next_zones_zonelist - Returns the next zone at or below highest_zoneidx within the allowed nodemask using a cursor within a zonelist as a starting point
* @z - The cursor used as a starting point for the search
* @highest_zoneidx - The zone index of the highest zone to return
* @nodes - An optional nodemask to filter the zonelist with
*
* This function returns the next zone at or below a given zone index that is
* within the allowed nodemask using a cursor as the starting point for the
* search. The zoneref returned is a cursor that represents the current zone
* being examined. It should be advanced by one before calling
* next_zones_zonelist again.
*/
struct zoneref *next_zones_zonelist(struct zoneref *z,
enum zone_type highest_zoneidx,
nodemask_t *nodes);
mm: have zonelist contains structs with both a zone pointer and zone_idx Filtering zonelists requires very frequent use of zone_idx(). This is costly as it involves a lookup of another structure and a substraction operation. As the zone_idx is often required, it should be quickly accessible. The node idx could also be stored here if it was found that accessing zone->node is significant which may be the case on workloads where nodemasks are heavily used. This patch introduces a struct zoneref to store a zone pointer and a zone index. The zonelist then consists of an array of these struct zonerefs which are looked up as necessary. Helpers are given for accessing the zone index as well as the node index. [kamezawa.hiroyu@jp.fujitsu.com: Suggested struct zoneref instead of embedding information in pointers] [hugh@veritas.com: mm-have-zonelist: fix memcg ooms] [hugh@veritas.com: just return do_try_to_free_pages] [hugh@veritas.com: do_try_to_free_pages gfp_mask redundant] Signed-off-by: Mel Gorman <mel@csn.ul.ie> Acked-by: Christoph Lameter <clameter@sgi.com> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Mel Gorman <mel@csn.ul.ie> Cc: Christoph Lameter <clameter@sgi.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Hugh Dickins <hugh@veritas.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 16:12:17 +07:00
/**
* first_zones_zonelist - Returns the first zone at or below highest_zoneidx within the allowed nodemask in a zonelist
* @zonelist - The zonelist to search for a suitable zone
* @highest_zoneidx - The zone index of the highest zone to return
* @nodes - An optional nodemask to filter the zonelist with
* @zone - The first suitable zone found is returned via this parameter
*
* This function returns the first zone at or below a given zone index that is
* within the allowed nodemask. The zoneref returned is a cursor that can be
* used to iterate the zonelist with next_zones_zonelist by advancing it by
* one before calling.
*/
mm: have zonelist contains structs with both a zone pointer and zone_idx Filtering zonelists requires very frequent use of zone_idx(). This is costly as it involves a lookup of another structure and a substraction operation. As the zone_idx is often required, it should be quickly accessible. The node idx could also be stored here if it was found that accessing zone->node is significant which may be the case on workloads where nodemasks are heavily used. This patch introduces a struct zoneref to store a zone pointer and a zone index. The zonelist then consists of an array of these struct zonerefs which are looked up as necessary. Helpers are given for accessing the zone index as well as the node index. [kamezawa.hiroyu@jp.fujitsu.com: Suggested struct zoneref instead of embedding information in pointers] [hugh@veritas.com: mm-have-zonelist: fix memcg ooms] [hugh@veritas.com: just return do_try_to_free_pages] [hugh@veritas.com: do_try_to_free_pages gfp_mask redundant] Signed-off-by: Mel Gorman <mel@csn.ul.ie> Acked-by: Christoph Lameter <clameter@sgi.com> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Mel Gorman <mel@csn.ul.ie> Cc: Christoph Lameter <clameter@sgi.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Hugh Dickins <hugh@veritas.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 16:12:17 +07:00
static inline struct zoneref *first_zones_zonelist(struct zonelist *zonelist,
enum zone_type highest_zoneidx,
nodemask_t *nodes,
struct zone **zone)
{
struct zoneref *z = next_zones_zonelist(zonelist->_zonerefs,
highest_zoneidx, nodes);
*zone = zonelist_zone(z);
return z;
}
/**
* for_each_zone_zonelist_nodemask - helper macro to iterate over valid zones in a zonelist at or below a given zone index and within a nodemask
* @zone - The current zone in the iterator
* @z - The current pointer within zonelist->zones being iterated
* @zlist - The zonelist being iterated
* @highidx - The zone index of the highest zone to return
* @nodemask - Nodemask allowed by the allocator
*
* This iterator iterates though all zones at or below a given zone index and
* within a given nodemask
*/
#define for_each_zone_zonelist_nodemask(zone, z, zlist, highidx, nodemask) \
for (z = first_zones_zonelist(zlist, highidx, nodemask, &zone); \
zone; \
z = next_zones_zonelist(++z, highidx, nodemask), \
zone = zonelist_zone(z)) \
/**
* for_each_zone_zonelist - helper macro to iterate over valid zones in a zonelist at or below a given zone index
* @zone - The current zone in the iterator
* @z - The current pointer within zonelist->zones being iterated
* @zlist - The zonelist being iterated
* @highidx - The zone index of the highest zone to return
*
* This iterator iterates though all zones at or below a given zone index.
*/
#define for_each_zone_zonelist(zone, z, zlist, highidx) \
for_each_zone_zonelist_nodemask(zone, z, zlist, highidx, NULL)
[PATCH] sparsemem memory model Sparsemem abstracts the use of discontiguous mem_maps[]. This kind of mem_map[] is needed by discontiguous memory machines (like in the old CONFIG_DISCONTIGMEM case) as well as memory hotplug systems. Sparsemem replaces DISCONTIGMEM when enabled, and it is hoped that it can eventually become a complete replacement. A significant advantage over DISCONTIGMEM is that it's completely separated from CONFIG_NUMA. When producing this patch, it became apparent in that NUMA and DISCONTIG are often confused. Another advantage is that sparse doesn't require each NUMA node's ranges to be contiguous. It can handle overlapping ranges between nodes with no problems, where DISCONTIGMEM currently throws away that memory. Sparsemem uses an array to provide different pfn_to_page() translations for each SECTION_SIZE area of physical memory. This is what allows the mem_map[] to be chopped up. In order to do quick pfn_to_page() operations, the section number of the page is encoded in page->flags. Part of the sparsemem infrastructure enables sharing of these bits more dynamically (at compile-time) between the page_zone() and sparsemem operations. However, on 32-bit architectures, the number of bits is quite limited, and may require growing the size of the page->flags type in certain conditions. Several things might force this to occur: a decrease in the SECTION_SIZE (if you want to hotplug smaller areas of memory), an increase in the physical address space, or an increase in the number of used page->flags. One thing to note is that, once sparsemem is present, the NUMA node information no longer needs to be stored in the page->flags. It might provide speed increases on certain platforms and will be stored there if there is room. But, if out of room, an alternate (theoretically slower) mechanism is used. This patch introduces CONFIG_FLATMEM. It is used in almost all cases where there used to be an #ifndef DISCONTIG, because SPARSEMEM and DISCONTIGMEM often have to compile out the same areas of code. Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Dave Hansen <haveblue@us.ibm.com> Signed-off-by: Martin Bligh <mbligh@aracnet.com> Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com> Signed-off-by: Bob Picco <bob.picco@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 14:07:54 +07:00
#ifdef CONFIG_SPARSEMEM
#include <asm/sparsemem.h>
#endif
[PATCH] Introduce mechanism for registering active regions of memory At a basic level, architectures define structures to record where active ranges of page frames are located. Once located, the code to calculate zone sizes and holes in each architecture is very similar. Some of this zone and hole sizing code is difficult to read for no good reason. This set of patches eliminates the similar-looking architecture-specific code. The patches introduce a mechanism where architectures register where the active ranges of page frames are with add_active_range(). When all areas have been discovered, free_area_init_nodes() is called to initialise the pgdat and zones. The zone sizes and holes are then calculated in an architecture independent manner. Patch 1 introduces the mechanism for registering and initialising PFN ranges Patch 2 changes ppc to use the mechanism - 139 arch-specific LOC removed Patch 3 changes x86 to use the mechanism - 136 arch-specific LOC removed Patch 4 changes x86_64 to use the mechanism - 74 arch-specific LOC removed Patch 5 changes ia64 to use the mechanism - 52 arch-specific LOC removed Patch 6 accounts for mem_map as a memory hole as the pages are not reclaimable. It adjusts the watermarks slightly Tony Luck has successfully tested for ia64 on Itanium with tiger_defconfig, gensparse_defconfig and defconfig. Bob Picco has also tested and debugged on IA64. Jack Steiner successfully boot tested on a mammoth SGI IA64-based machine. These were on patches against 2.6.17-rc1 and release 3 of these patches but there have been no ia64-changes since release 3. There are differences in the zone sizes for x86_64 as the arch-specific code for x86_64 accounts the kernel image and the starting mem_maps as memory holes but the architecture-independent code accounts the memory as present. The big benefit of this set of patches is a sizable reduction of architecture-specific code, some of which is very hairy. There should be a greater reduction when other architectures use the same mechanisms for zone and hole sizing but I lack the hardware to test on. Additional credit; Dave Hansen for the initial suggestion and comments on early patches Andy Whitcroft for reviewing early versions and catching numerous errors Tony Luck for testing and debugging on IA64 Bob Picco for fixing bugs related to pfn registration, reviewing a number of patch revisions, providing a number of suggestions on future direction and testing heavily Jack Steiner and Robin Holt for testing on IA64 and clarifying issues related to memory holes Yasunori for testing on IA64 Andi Kleen for reviewing and feeding back about x86_64 Christian Kujau for providing valuable information related to ACPI problems on x86_64 and testing potential fixes This patch: Define the structure to represent an active range of page frames within a node in an architecture independent manner. Architectures are expected to register active ranges of PFNs using add_active_range(nid, start_pfn, end_pfn) and call free_area_init_nodes() passing the PFNs of the end of each zone. Signed-off-by: Mel Gorman <mel@csn.ul.ie> Signed-off-by: Bob Picco <bob.picco@hp.com> Cc: Dave Hansen <haveblue@us.ibm.com> Cc: Andy Whitcroft <apw@shadowen.org> Cc: Andi Kleen <ak@muc.de> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: "Keith Mannthey" <kmannth@gmail.com> Cc: "Luck, Tony" <tony.luck@intel.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Yasunori Goto <y-goto@jp.fujitsu.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-09-27 15:49:43 +07:00
#if !defined(CONFIG_HAVE_ARCH_EARLY_PFN_TO_NID) && \
!defined(CONFIG_HAVE_MEMBLOCK_NODE_MAP)
static inline unsigned long early_pfn_to_nid(unsigned long pfn)
{
return 0;
}
#endif
[PATCH] flatmem split out memory model There are three places we define pfn_to_nid(). Two in linux/mmzone.h and one in asm/mmzone.h. These in essence represent the three memory models. The definition in linux/mmzone.h under !NEED_MULTIPLE_NODES is both the FLATMEM definition and the optimisation for single NUMA nodes; the one under SPARSEMEM is the NUMA sparsemem one; the one in asm/mmzone.h under DISCONTIGMEM is the discontigmem one. This is not in the least bit obvious, particularly the connection between the non-NUMA optimisations and the memory models. Two patches: flatmem-split-out-memory-model: simplifies the selection of pfn_to_nid() implementations. The selection is based primarily off the memory model selected. Optimisations for non-NUMA are applied where needed. sparse-provide-pfn_to_nid: implement pfn_to_nid() for SPARSEMEM This patch: pfn_to_nid is memory model specific The pfn_to_nid() call is memory model specific. It represents the locality identifier for the memory passed. Classically this would be a NUMA node, but not a chunk of memory under DISCONTIGMEM. The SPARSEMEM and FLATMEM memory model non-NUMA versions of pfn_to_nid() are folded together under NEED_MULTIPLE_NODES, while DISCONTIGMEM has its own optimisation. This is all very confusing. This patch splits out each implementation of pfn_to_nid() so that we can see them and the optimisations to each. Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 15:10:53 +07:00
#ifdef CONFIG_FLATMEM
#define pfn_to_nid(pfn) (0)
#endif
[PATCH] sparsemem memory model Sparsemem abstracts the use of discontiguous mem_maps[]. This kind of mem_map[] is needed by discontiguous memory machines (like in the old CONFIG_DISCONTIGMEM case) as well as memory hotplug systems. Sparsemem replaces DISCONTIGMEM when enabled, and it is hoped that it can eventually become a complete replacement. A significant advantage over DISCONTIGMEM is that it's completely separated from CONFIG_NUMA. When producing this patch, it became apparent in that NUMA and DISCONTIG are often confused. Another advantage is that sparse doesn't require each NUMA node's ranges to be contiguous. It can handle overlapping ranges between nodes with no problems, where DISCONTIGMEM currently throws away that memory. Sparsemem uses an array to provide different pfn_to_page() translations for each SECTION_SIZE area of physical memory. This is what allows the mem_map[] to be chopped up. In order to do quick pfn_to_page() operations, the section number of the page is encoded in page->flags. Part of the sparsemem infrastructure enables sharing of these bits more dynamically (at compile-time) between the page_zone() and sparsemem operations. However, on 32-bit architectures, the number of bits is quite limited, and may require growing the size of the page->flags type in certain conditions. Several things might force this to occur: a decrease in the SECTION_SIZE (if you want to hotplug smaller areas of memory), an increase in the physical address space, or an increase in the number of used page->flags. One thing to note is that, once sparsemem is present, the NUMA node information no longer needs to be stored in the page->flags. It might provide speed increases on certain platforms and will be stored there if there is room. But, if out of room, an alternate (theoretically slower) mechanism is used. This patch introduces CONFIG_FLATMEM. It is used in almost all cases where there used to be an #ifndef DISCONTIG, because SPARSEMEM and DISCONTIGMEM often have to compile out the same areas of code. Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Dave Hansen <haveblue@us.ibm.com> Signed-off-by: Martin Bligh <mbligh@aracnet.com> Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com> Signed-off-by: Bob Picco <bob.picco@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 14:07:54 +07:00
#ifdef CONFIG_SPARSEMEM
/*
* SECTION_SHIFT #bits space required to store a section #
*
* PA_SECTION_SHIFT physical address to/from section number
* PFN_SECTION_SHIFT pfn to/from section number
*/
#define PA_SECTION_SHIFT (SECTION_SIZE_BITS)
#define PFN_SECTION_SHIFT (SECTION_SIZE_BITS - PAGE_SHIFT)
#define NR_MEM_SECTIONS (1UL << SECTIONS_SHIFT)
#define PAGES_PER_SECTION (1UL << PFN_SECTION_SHIFT)
#define PAGE_SECTION_MASK (~(PAGES_PER_SECTION-1))
Add a bitmap that is used to track flags affecting a block of pages Here is the latest revision of the anti-fragmentation patches. Of particular note in this version is special treatment of high-order atomic allocations. Care is taken to group them together and avoid grouping pages of other types near them. Artifical tests imply that it works. I'm trying to get the hardware together that would allow setting up of a "real" test. If anyone already has a setup and test that can trigger the atomic-allocation problem, I'd appreciate a test of these patches and a report. The second major change is that these patches will apply cleanly with patches that implement anti-fragmentation through zones. kernbench shows effectively no performance difference varying between -0.2% and +2% on a variety of test machines. Success rates for huge page allocation are dramatically increased. For example, on a ppc64 machine, the vanilla kernel was only able to allocate 1% of memory as a hugepage and this was due to a single hugepage reserved as min_free_kbytes. With these patches applied, 17% was allocatable as superpages. With reclaim-related fixes from Andy Whitcroft, it was 40% and further reclaim-related improvements should increase this further. Changelog Since V28 o Group high-order atomic allocations together o It is no longer required to set min_free_kbytes to 10% of memory. A value of 16384 in most cases will be sufficient o Now applied with zone-based anti-fragmentation o Fix incorrect VM_BUG_ON within buffered_rmqueue() o Reorder the stack so later patches do not back out work from earlier patches o Fix bug were journal pages were being treated as movable o Bias placement of non-movable pages to lower PFNs o More agressive clustering of reclaimable pages in reactions to workloads like updatedb that flood the size of inode caches Changelog Since V27 o Renamed anti-fragmentation to Page Clustering. Anti-fragmentation was giving the mistaken impression that it was the 100% solution for high order allocations. Instead, it greatly increases the chances high-order allocations will succeed and lays the foundation for defragmentation and memory hot-remove to work properly o Redefine page groupings based on ability to migrate or reclaim instead of basing on reclaimability alone o Get rid of spurious inits o Per-cpu lists are no longer split up per-type. Instead the per-cpu list is searched for a page of the appropriate type o Added more explanation commentary o Fix up bug in pageblock code where bitmap was used before being initalised Changelog Since V26 o Fix double init of lists in setup_pageset Changelog Since V25 o Fix loop order of for_each_rclmtype_order so that order of loop matches args o gfpflags_to_rclmtype uses gfp_t instead of unsigned long o Rename get_pageblock_type() to get_page_rclmtype() o Fix alignment problem in move_freepages() o Add mechanism for assigning flags to blocks of pages instead of page->flags o On fallback, do not examine the preferred list of free pages a second time The purpose of these patches is to reduce external fragmentation by grouping pages of related types together. When pages are migrated (or reclaimed under memory pressure), large contiguous pages will be freed. This patch works by categorising allocations by their ability to migrate; Movable - The pages may be moved with the page migration mechanism. These are generally userspace pages. Reclaimable - These are allocations for some kernel caches that are reclaimable or allocations that are known to be very short-lived. Unmovable - These are pages that are allocated by the kernel that are not trivially reclaimed. For example, the memory allocated for a loaded module would be in this category. By default, allocations are considered to be of this type HighAtomic - These are high-order allocations belonging to callers that cannot sleep or perform any IO. In practice, this is restricted to jumbo frame allocation for network receive. It is assumed that the allocations are short-lived Instead of having one MAX_ORDER-sized array of free lists in struct free_area, there is one for each type of reclaimability. Once a 2^MAX_ORDER block of pages is split for a type of allocation, it is added to the free-lists for that type, in effect reserving it. Hence, over time, pages of the different types can be clustered together. When the preferred freelists are expired, the largest possible block is taken from an alternative list. Buddies that are split from that large block are placed on the preferred allocation-type freelists to mitigate fragmentation. This implementation gives best-effort for low fragmentation in all zones. Ideally, min_free_kbytes needs to be set to a value equal to 4 * (1 << (MAX_ORDER-1)) pages in most cases. This would be 16384 on x86 and x86_64 for example. Our tests show that about 60-70% of physical memory can be allocated on a desktop after a few days uptime. In benchmarks and stress tests, we are finding that 80% of memory is available as contiguous blocks at the end of the test. To compare, a standard kernel was getting < 1% of memory as large pages on a desktop and about 8-12% of memory as large pages at the end of stress tests. Following this email are 12 patches that implement thie page grouping feature. The first patch introduces a mechanism for storing flags related to a whole block of pages. Then allocations are split between movable and all other allocations. Following that are patches to deal with per-cpu pages and make the mechanism configurable. The next patch moves free pages between lists when partially allocated blocks are used for pages of another migrate type. The second last patch groups reclaimable kernel allocations such as inode caches together. The final patch related to groupings keeps high-order atomic allocations. The last two patches are more concerned with control of fragmentation. The second last patch biases placement of non-movable allocations towards the start of memory. This is with a view of supporting memory hot-remove of DIMMs with higher PFNs in the future. The biasing could be enforced a lot heavier but it would cost. The last patch agressively clusters reclaimable pages like inode caches together. The fragmentation reduction strategy needs to track if pages within a block can be moved or reclaimed so that pages are freed to the appropriate list. This patch adds a bitmap for flags affecting a whole a MAX_ORDER block of pages. In non-SPARSEMEM configurations, the bitmap is stored in the struct zone and allocated during initialisation. SPARSEMEM statically allocates the bitmap in a struct mem_section so that bitmaps do not have to be resized during memory hotadd. This wastes a small amount of memory per unused section (usually sizeof(unsigned long)) but the complexity of dynamically allocating the memory is quite high. Additional credit to Andy Whitcroft who reviewed up an earlier implementation of the mechanism an suggested how to make it a *lot* cleaner. Signed-off-by: Mel Gorman <mel@csn.ul.ie> Cc: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16 15:25:47 +07:00
#define SECTION_BLOCKFLAGS_BITS \
Do not depend on MAX_ORDER when grouping pages by mobility Currently mobility grouping works at the MAX_ORDER_NR_PAGES level. This makes sense for the majority of users where this is also the huge page size. However, on platforms like ia64 where the huge page size is runtime configurable it is desirable to group at a lower order. On x86_64 and occasionally on x86, the hugepage size may not always be MAX_ORDER_NR_PAGES. This patch groups pages together based on the value of HUGETLB_PAGE_ORDER. It uses a compile-time constant if possible and a variable where the huge page size is runtime configurable. It is assumed that grouping should be done at the lowest sensible order and that the user would not want to override this. If this is not true, page_block order could be forced to a variable initialised via a boot-time kernel parameter. One potential issue with this patch is that IA64 now parses hugepagesz with early_param() instead of __setup(). __setup() is called after the memory allocator has been initialised and the pageblock bitmaps already setup. In tests on one IA64 there did not seem to be any problem with using early_param() and in fact may be more correct as it guarantees the parameter is handled before the parsing of hugepages=. Signed-off-by: Mel Gorman <mel@csn.ul.ie> Acked-by: Andy Whitcroft <apw@shadowen.org> Acked-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16 15:26:01 +07:00
((1UL << (PFN_SECTION_SHIFT - pageblock_order)) * NR_PAGEBLOCK_BITS)
Add a bitmap that is used to track flags affecting a block of pages Here is the latest revision of the anti-fragmentation patches. Of particular note in this version is special treatment of high-order atomic allocations. Care is taken to group them together and avoid grouping pages of other types near them. Artifical tests imply that it works. I'm trying to get the hardware together that would allow setting up of a "real" test. If anyone already has a setup and test that can trigger the atomic-allocation problem, I'd appreciate a test of these patches and a report. The second major change is that these patches will apply cleanly with patches that implement anti-fragmentation through zones. kernbench shows effectively no performance difference varying between -0.2% and +2% on a variety of test machines. Success rates for huge page allocation are dramatically increased. For example, on a ppc64 machine, the vanilla kernel was only able to allocate 1% of memory as a hugepage and this was due to a single hugepage reserved as min_free_kbytes. With these patches applied, 17% was allocatable as superpages. With reclaim-related fixes from Andy Whitcroft, it was 40% and further reclaim-related improvements should increase this further. Changelog Since V28 o Group high-order atomic allocations together o It is no longer required to set min_free_kbytes to 10% of memory. A value of 16384 in most cases will be sufficient o Now applied with zone-based anti-fragmentation o Fix incorrect VM_BUG_ON within buffered_rmqueue() o Reorder the stack so later patches do not back out work from earlier patches o Fix bug were journal pages were being treated as movable o Bias placement of non-movable pages to lower PFNs o More agressive clustering of reclaimable pages in reactions to workloads like updatedb that flood the size of inode caches Changelog Since V27 o Renamed anti-fragmentation to Page Clustering. Anti-fragmentation was giving the mistaken impression that it was the 100% solution for high order allocations. Instead, it greatly increases the chances high-order allocations will succeed and lays the foundation for defragmentation and memory hot-remove to work properly o Redefine page groupings based on ability to migrate or reclaim instead of basing on reclaimability alone o Get rid of spurious inits o Per-cpu lists are no longer split up per-type. Instead the per-cpu list is searched for a page of the appropriate type o Added more explanation commentary o Fix up bug in pageblock code where bitmap was used before being initalised Changelog Since V26 o Fix double init of lists in setup_pageset Changelog Since V25 o Fix loop order of for_each_rclmtype_order so that order of loop matches args o gfpflags_to_rclmtype uses gfp_t instead of unsigned long o Rename get_pageblock_type() to get_page_rclmtype() o Fix alignment problem in move_freepages() o Add mechanism for assigning flags to blocks of pages instead of page->flags o On fallback, do not examine the preferred list of free pages a second time The purpose of these patches is to reduce external fragmentation by grouping pages of related types together. When pages are migrated (or reclaimed under memory pressure), large contiguous pages will be freed. This patch works by categorising allocations by their ability to migrate; Movable - The pages may be moved with the page migration mechanism. These are generally userspace pages. Reclaimable - These are allocations for some kernel caches that are reclaimable or allocations that are known to be very short-lived. Unmovable - These are pages that are allocated by the kernel that are not trivially reclaimed. For example, the memory allocated for a loaded module would be in this category. By default, allocations are considered to be of this type HighAtomic - These are high-order allocations belonging to callers that cannot sleep or perform any IO. In practice, this is restricted to jumbo frame allocation for network receive. It is assumed that the allocations are short-lived Instead of having one MAX_ORDER-sized array of free lists in struct free_area, there is one for each type of reclaimability. Once a 2^MAX_ORDER block of pages is split for a type of allocation, it is added to the free-lists for that type, in effect reserving it. Hence, over time, pages of the different types can be clustered together. When the preferred freelists are expired, the largest possible block is taken from an alternative list. Buddies that are split from that large block are placed on the preferred allocation-type freelists to mitigate fragmentation. This implementation gives best-effort for low fragmentation in all zones. Ideally, min_free_kbytes needs to be set to a value equal to 4 * (1 << (MAX_ORDER-1)) pages in most cases. This would be 16384 on x86 and x86_64 for example. Our tests show that about 60-70% of physical memory can be allocated on a desktop after a few days uptime. In benchmarks and stress tests, we are finding that 80% of memory is available as contiguous blocks at the end of the test. To compare, a standard kernel was getting < 1% of memory as large pages on a desktop and about 8-12% of memory as large pages at the end of stress tests. Following this email are 12 patches that implement thie page grouping feature. The first patch introduces a mechanism for storing flags related to a whole block of pages. Then allocations are split between movable and all other allocations. Following that are patches to deal with per-cpu pages and make the mechanism configurable. The next patch moves free pages between lists when partially allocated blocks are used for pages of another migrate type. The second last patch groups reclaimable kernel allocations such as inode caches together. The final patch related to groupings keeps high-order atomic allocations. The last two patches are more concerned with control of fragmentation. The second last patch biases placement of non-movable allocations towards the start of memory. This is with a view of supporting memory hot-remove of DIMMs with higher PFNs in the future. The biasing could be enforced a lot heavier but it would cost. The last patch agressively clusters reclaimable pages like inode caches together. The fragmentation reduction strategy needs to track if pages within a block can be moved or reclaimed so that pages are freed to the appropriate list. This patch adds a bitmap for flags affecting a whole a MAX_ORDER block of pages. In non-SPARSEMEM configurations, the bitmap is stored in the struct zone and allocated during initialisation. SPARSEMEM statically allocates the bitmap in a struct mem_section so that bitmaps do not have to be resized during memory hotadd. This wastes a small amount of memory per unused section (usually sizeof(unsigned long)) but the complexity of dynamically allocating the memory is quite high. Additional credit to Andy Whitcroft who reviewed up an earlier implementation of the mechanism an suggested how to make it a *lot* cleaner. Signed-off-by: Mel Gorman <mel@csn.ul.ie> Cc: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16 15:25:47 +07:00
[PATCH] sparsemem memory model Sparsemem abstracts the use of discontiguous mem_maps[]. This kind of mem_map[] is needed by discontiguous memory machines (like in the old CONFIG_DISCONTIGMEM case) as well as memory hotplug systems. Sparsemem replaces DISCONTIGMEM when enabled, and it is hoped that it can eventually become a complete replacement. A significant advantage over DISCONTIGMEM is that it's completely separated from CONFIG_NUMA. When producing this patch, it became apparent in that NUMA and DISCONTIG are often confused. Another advantage is that sparse doesn't require each NUMA node's ranges to be contiguous. It can handle overlapping ranges between nodes with no problems, where DISCONTIGMEM currently throws away that memory. Sparsemem uses an array to provide different pfn_to_page() translations for each SECTION_SIZE area of physical memory. This is what allows the mem_map[] to be chopped up. In order to do quick pfn_to_page() operations, the section number of the page is encoded in page->flags. Part of the sparsemem infrastructure enables sharing of these bits more dynamically (at compile-time) between the page_zone() and sparsemem operations. However, on 32-bit architectures, the number of bits is quite limited, and may require growing the size of the page->flags type in certain conditions. Several things might force this to occur: a decrease in the SECTION_SIZE (if you want to hotplug smaller areas of memory), an increase in the physical address space, or an increase in the number of used page->flags. One thing to note is that, once sparsemem is present, the NUMA node information no longer needs to be stored in the page->flags. It might provide speed increases on certain platforms and will be stored there if there is room. But, if out of room, an alternate (theoretically slower) mechanism is used. This patch introduces CONFIG_FLATMEM. It is used in almost all cases where there used to be an #ifndef DISCONTIG, because SPARSEMEM and DISCONTIGMEM often have to compile out the same areas of code. Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Dave Hansen <haveblue@us.ibm.com> Signed-off-by: Martin Bligh <mbligh@aracnet.com> Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com> Signed-off-by: Bob Picco <bob.picco@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 14:07:54 +07:00
#if (MAX_ORDER - 1 + PAGE_SHIFT) > SECTION_SIZE_BITS
#error Allocator MAX_ORDER exceeds SECTION_SIZE
#endif
#define pfn_to_section_nr(pfn) ((pfn) >> PFN_SECTION_SHIFT)
#define section_nr_to_pfn(sec) ((sec) << PFN_SECTION_SHIFT)
#define SECTION_ALIGN_UP(pfn) (((pfn) + PAGES_PER_SECTION - 1) & PAGE_SECTION_MASK)
#define SECTION_ALIGN_DOWN(pfn) ((pfn) & PAGE_SECTION_MASK)
[PATCH] sparsemem memory model Sparsemem abstracts the use of discontiguous mem_maps[]. This kind of mem_map[] is needed by discontiguous memory machines (like in the old CONFIG_DISCONTIGMEM case) as well as memory hotplug systems. Sparsemem replaces DISCONTIGMEM when enabled, and it is hoped that it can eventually become a complete replacement. A significant advantage over DISCONTIGMEM is that it's completely separated from CONFIG_NUMA. When producing this patch, it became apparent in that NUMA and DISCONTIG are often confused. Another advantage is that sparse doesn't require each NUMA node's ranges to be contiguous. It can handle overlapping ranges between nodes with no problems, where DISCONTIGMEM currently throws away that memory. Sparsemem uses an array to provide different pfn_to_page() translations for each SECTION_SIZE area of physical memory. This is what allows the mem_map[] to be chopped up. In order to do quick pfn_to_page() operations, the section number of the page is encoded in page->flags. Part of the sparsemem infrastructure enables sharing of these bits more dynamically (at compile-time) between the page_zone() and sparsemem operations. However, on 32-bit architectures, the number of bits is quite limited, and may require growing the size of the page->flags type in certain conditions. Several things might force this to occur: a decrease in the SECTION_SIZE (if you want to hotplug smaller areas of memory), an increase in the physical address space, or an increase in the number of used page->flags. One thing to note is that, once sparsemem is present, the NUMA node information no longer needs to be stored in the page->flags. It might provide speed increases on certain platforms and will be stored there if there is room. But, if out of room, an alternate (theoretically slower) mechanism is used. This patch introduces CONFIG_FLATMEM. It is used in almost all cases where there used to be an #ifndef DISCONTIG, because SPARSEMEM and DISCONTIGMEM often have to compile out the same areas of code. Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Dave Hansen <haveblue@us.ibm.com> Signed-off-by: Martin Bligh <mbligh@aracnet.com> Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com> Signed-off-by: Bob Picco <bob.picco@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 14:07:54 +07:00
struct page;
mm/page_ext: resurrect struct page extending code for debugging When we debug something, we'd like to insert some information to every page. For this purpose, we sometimes modify struct page itself. But, this has drawbacks. First, it requires re-compile. This makes us hesitate to use the powerful debug feature so development process is slowed down. And, second, sometimes it is impossible to rebuild the kernel due to third party module dependency. At third, system behaviour would be largely different after re-compile, because it changes size of struct page greatly and this structure is accessed by every part of kernel. Keeping this as it is would be better to reproduce errornous situation. This feature is intended to overcome above mentioned problems. This feature allocates memory for extended data per page in certain place rather than the struct page itself. This memory can be accessed by the accessor functions provided by this code. During the boot process, it checks whether allocation of huge chunk of memory is needed or not. If not, it avoids allocating memory at all. With this advantage, we can include this feature into the kernel in default and can avoid rebuild and solve related problems. Until now, memcg uses this technique. But, now, memcg decides to embed their variable to struct page itself and it's code to extend struct page has been removed. I'd like to use this code to develop debug feature, so this patch resurrect it. To help these things to work well, this patch introduces two callbacks for clients. One is the need callback which is mandatory if user wants to avoid useless memory allocation at boot-time. The other is optional, init callback, which is used to do proper initialization after memory is allocated. Detailed explanation about purpose of these functions is in code comment. Please refer it. Others are completely same with previous extension code in memcg. Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Minchan Kim <minchan@kernel.org> Cc: Dave Hansen <dave@sr71.net> Cc: Michal Nazarewicz <mina86@mina86.com> Cc: Jungsoo Son <jungsoo.son@lge.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-12-13 07:55:46 +07:00
struct page_ext;
[PATCH] sparsemem memory model Sparsemem abstracts the use of discontiguous mem_maps[]. This kind of mem_map[] is needed by discontiguous memory machines (like in the old CONFIG_DISCONTIGMEM case) as well as memory hotplug systems. Sparsemem replaces DISCONTIGMEM when enabled, and it is hoped that it can eventually become a complete replacement. A significant advantage over DISCONTIGMEM is that it's completely separated from CONFIG_NUMA. When producing this patch, it became apparent in that NUMA and DISCONTIG are often confused. Another advantage is that sparse doesn't require each NUMA node's ranges to be contiguous. It can handle overlapping ranges between nodes with no problems, where DISCONTIGMEM currently throws away that memory. Sparsemem uses an array to provide different pfn_to_page() translations for each SECTION_SIZE area of physical memory. This is what allows the mem_map[] to be chopped up. In order to do quick pfn_to_page() operations, the section number of the page is encoded in page->flags. Part of the sparsemem infrastructure enables sharing of these bits more dynamically (at compile-time) between the page_zone() and sparsemem operations. However, on 32-bit architectures, the number of bits is quite limited, and may require growing the size of the page->flags type in certain conditions. Several things might force this to occur: a decrease in the SECTION_SIZE (if you want to hotplug smaller areas of memory), an increase in the physical address space, or an increase in the number of used page->flags. One thing to note is that, once sparsemem is present, the NUMA node information no longer needs to be stored in the page->flags. It might provide speed increases on certain platforms and will be stored there if there is room. But, if out of room, an alternate (theoretically slower) mechanism is used. This patch introduces CONFIG_FLATMEM. It is used in almost all cases where there used to be an #ifndef DISCONTIG, because SPARSEMEM and DISCONTIGMEM often have to compile out the same areas of code. Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Dave Hansen <haveblue@us.ibm.com> Signed-off-by: Martin Bligh <mbligh@aracnet.com> Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com> Signed-off-by: Bob Picco <bob.picco@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 14:07:54 +07:00
struct mem_section {
[PATCH] sparsemem hotplug base Make sparse's initalization be accessible at runtime. This allows sparse mappings to be created after boot in a hotplug situation. This patch is separated from the previous one just to give an indication how much of the sparse infrastructure is *just* for hotplug memory. The section_mem_map doesn't really store a pointer. It stores something that is convenient to do some math against to get a pointer. It isn't valid to just do *section_mem_map, so I don't think it should be stored as a pointer. There are a couple of things I'd like to store about a section. First of all, the fact that it is !NULL does not mean that it is present. There could be such a combination where section_mem_map *is* NULL, but the math gets you properly to a real mem_map. So, I don't think that check is safe. Since we're storing 32-bit-aligned structures, we have a few bits in the bottom of the pointer to play with. Use one bit to encode whether there's really a mem_map there, and the other one to tell whether there's a valid section there. We need to distinguish between the two because sometimes there's a gap between when a section is discovered to be present and when we can get the mem_map for it. Signed-off-by: Dave Hansen <haveblue@us.ibm.com> Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Jack Steiner <steiner@sgi.com> Signed-off-by: Bob Picco <bob.picco@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 14:08:00 +07:00
/*
* This is, logically, a pointer to an array of struct
* pages. However, it is stored with some other magic.
* (see sparse.c::sparse_init_one_section())
*
* Additionally during early boot we encode node id of
* the location of the section here to guide allocation.
* (see sparse.c::memory_present())
*
[PATCH] sparsemem hotplug base Make sparse's initalization be accessible at runtime. This allows sparse mappings to be created after boot in a hotplug situation. This patch is separated from the previous one just to give an indication how much of the sparse infrastructure is *just* for hotplug memory. The section_mem_map doesn't really store a pointer. It stores something that is convenient to do some math against to get a pointer. It isn't valid to just do *section_mem_map, so I don't think it should be stored as a pointer. There are a couple of things I'd like to store about a section. First of all, the fact that it is !NULL does not mean that it is present. There could be such a combination where section_mem_map *is* NULL, but the math gets you properly to a real mem_map. So, I don't think that check is safe. Since we're storing 32-bit-aligned structures, we have a few bits in the bottom of the pointer to play with. Use one bit to encode whether there's really a mem_map there, and the other one to tell whether there's a valid section there. We need to distinguish between the two because sometimes there's a gap between when a section is discovered to be present and when we can get the mem_map for it. Signed-off-by: Dave Hansen <haveblue@us.ibm.com> Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Jack Steiner <steiner@sgi.com> Signed-off-by: Bob Picco <bob.picco@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 14:08:00 +07:00
* Making it a UL at least makes someone do a cast
* before using it wrong.
*/
unsigned long section_mem_map;
Fix corruption of memmap on IA64 SPARSEMEM when mem_section is not a power of 2 There are problems in the use of SPARSEMEM and pageblock flags that causes problems on ia64. The first part of the problem is that units are incorrect in SECTION_BLOCKFLAGS_BITS computation. This results in a map_section's section_mem_map being treated as part of a bitmap which isn't good. This was evident with an invalid virtual address when mem_init attempted to free bootmem pages while relinquishing control from the bootmem allocator. The second part of the problem occurs because the pageblock flags bitmap is be located with the mem_section. The SECTIONS_PER_ROOT computation using sizeof (mem_section) may not be a power of 2 depending on the size of the bitmap. This renders masks and other such things not power of 2 base. This issue was seen with SPARSEMEM_EXTREME on ia64. This patch moves the bitmap outside of mem_section and uses a pointer instead in the mem_section. The bitmaps are allocated when the section is being initialised. Note that sparse_early_usemap_alloc() does not use alloc_remap() like sparse_early_mem_map_alloc(). The allocation required for the bitmap on x86, the only architecture that uses alloc_remap is typically smaller than a cache line. alloc_remap() pads out allocations to the cache size which would be a needless waste. Credit to Bob Picco for identifying the original problem and effecting a fix for the SECTION_BLOCKFLAGS_BITS calculation. Credit to Andy Whitcroft for devising the best way of allocating the bitmaps only when required for the section. [wli@holomorphy.com: warning fix] Signed-off-by: Bob Picco <bob.picco@hp.com> Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Mel Gorman <mel@csn.ul.ie> Cc: "Luck, Tony" <tony.luck@intel.com> Signed-off-by: William Irwin <bill.irwin@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16 15:25:56 +07:00
/* See declaration of similar field in struct zone */
unsigned long *pageblock_flags;
mm/page_ext: resurrect struct page extending code for debugging When we debug something, we'd like to insert some information to every page. For this purpose, we sometimes modify struct page itself. But, this has drawbacks. First, it requires re-compile. This makes us hesitate to use the powerful debug feature so development process is slowed down. And, second, sometimes it is impossible to rebuild the kernel due to third party module dependency. At third, system behaviour would be largely different after re-compile, because it changes size of struct page greatly and this structure is accessed by every part of kernel. Keeping this as it is would be better to reproduce errornous situation. This feature is intended to overcome above mentioned problems. This feature allocates memory for extended data per page in certain place rather than the struct page itself. This memory can be accessed by the accessor functions provided by this code. During the boot process, it checks whether allocation of huge chunk of memory is needed or not. If not, it avoids allocating memory at all. With this advantage, we can include this feature into the kernel in default and can avoid rebuild and solve related problems. Until now, memcg uses this technique. But, now, memcg decides to embed their variable to struct page itself and it's code to extend struct page has been removed. I'd like to use this code to develop debug feature, so this patch resurrect it. To help these things to work well, this patch introduces two callbacks for clients. One is the need callback which is mandatory if user wants to avoid useless memory allocation at boot-time. The other is optional, init callback, which is used to do proper initialization after memory is allocated. Detailed explanation about purpose of these functions is in code comment. Please refer it. Others are completely same with previous extension code in memcg. Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Minchan Kim <minchan@kernel.org> Cc: Dave Hansen <dave@sr71.net> Cc: Michal Nazarewicz <mina86@mina86.com> Cc: Jungsoo Son <jungsoo.son@lge.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-12-13 07:55:46 +07:00
#ifdef CONFIG_PAGE_EXTENSION
/*
* If !SPARSEMEM, pgdat doesn't have page_ext pointer. We use
* section. (see page_ext.h about this.)
*/
struct page_ext *page_ext;
unsigned long pad;
#endif
/*
* WARNING: mem_section must be a power-of-2 in size for the
* calculation and use of SECTION_ROOT_MASK to make sense.
*/
[PATCH] sparsemem memory model Sparsemem abstracts the use of discontiguous mem_maps[]. This kind of mem_map[] is needed by discontiguous memory machines (like in the old CONFIG_DISCONTIGMEM case) as well as memory hotplug systems. Sparsemem replaces DISCONTIGMEM when enabled, and it is hoped that it can eventually become a complete replacement. A significant advantage over DISCONTIGMEM is that it's completely separated from CONFIG_NUMA. When producing this patch, it became apparent in that NUMA and DISCONTIG are often confused. Another advantage is that sparse doesn't require each NUMA node's ranges to be contiguous. It can handle overlapping ranges between nodes with no problems, where DISCONTIGMEM currently throws away that memory. Sparsemem uses an array to provide different pfn_to_page() translations for each SECTION_SIZE area of physical memory. This is what allows the mem_map[] to be chopped up. In order to do quick pfn_to_page() operations, the section number of the page is encoded in page->flags. Part of the sparsemem infrastructure enables sharing of these bits more dynamically (at compile-time) between the page_zone() and sparsemem operations. However, on 32-bit architectures, the number of bits is quite limited, and may require growing the size of the page->flags type in certain conditions. Several things might force this to occur: a decrease in the SECTION_SIZE (if you want to hotplug smaller areas of memory), an increase in the physical address space, or an increase in the number of used page->flags. One thing to note is that, once sparsemem is present, the NUMA node information no longer needs to be stored in the page->flags. It might provide speed increases on certain platforms and will be stored there if there is room. But, if out of room, an alternate (theoretically slower) mechanism is used. This patch introduces CONFIG_FLATMEM. It is used in almost all cases where there used to be an #ifndef DISCONTIG, because SPARSEMEM and DISCONTIGMEM often have to compile out the same areas of code. Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Dave Hansen <haveblue@us.ibm.com> Signed-off-by: Martin Bligh <mbligh@aracnet.com> Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com> Signed-off-by: Bob Picco <bob.picco@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 14:07:54 +07:00
};
#ifdef CONFIG_SPARSEMEM_EXTREME
#define SECTIONS_PER_ROOT (PAGE_SIZE / sizeof (struct mem_section))
#else
#define SECTIONS_PER_ROOT 1
#endif
#define SECTION_NR_TO_ROOT(sec) ((sec) / SECTIONS_PER_ROOT)
#define NR_SECTION_ROOTS DIV_ROUND_UP(NR_MEM_SECTIONS, SECTIONS_PER_ROOT)
#define SECTION_ROOT_MASK (SECTIONS_PER_ROOT - 1)
#ifdef CONFIG_SPARSEMEM_EXTREME
extern struct mem_section *mem_section[NR_SECTION_ROOTS];
#else
extern struct mem_section mem_section[NR_SECTION_ROOTS][SECTIONS_PER_ROOT];
#endif
[PATCH] sparsemem memory model Sparsemem abstracts the use of discontiguous mem_maps[]. This kind of mem_map[] is needed by discontiguous memory machines (like in the old CONFIG_DISCONTIGMEM case) as well as memory hotplug systems. Sparsemem replaces DISCONTIGMEM when enabled, and it is hoped that it can eventually become a complete replacement. A significant advantage over DISCONTIGMEM is that it's completely separated from CONFIG_NUMA. When producing this patch, it became apparent in that NUMA and DISCONTIG are often confused. Another advantage is that sparse doesn't require each NUMA node's ranges to be contiguous. It can handle overlapping ranges between nodes with no problems, where DISCONTIGMEM currently throws away that memory. Sparsemem uses an array to provide different pfn_to_page() translations for each SECTION_SIZE area of physical memory. This is what allows the mem_map[] to be chopped up. In order to do quick pfn_to_page() operations, the section number of the page is encoded in page->flags. Part of the sparsemem infrastructure enables sharing of these bits more dynamically (at compile-time) between the page_zone() and sparsemem operations. However, on 32-bit architectures, the number of bits is quite limited, and may require growing the size of the page->flags type in certain conditions. Several things might force this to occur: a decrease in the SECTION_SIZE (if you want to hotplug smaller areas of memory), an increase in the physical address space, or an increase in the number of used page->flags. One thing to note is that, once sparsemem is present, the NUMA node information no longer needs to be stored in the page->flags. It might provide speed increases on certain platforms and will be stored there if there is room. But, if out of room, an alternate (theoretically slower) mechanism is used. This patch introduces CONFIG_FLATMEM. It is used in almost all cases where there used to be an #ifndef DISCONTIG, because SPARSEMEM and DISCONTIGMEM often have to compile out the same areas of code. Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Dave Hansen <haveblue@us.ibm.com> Signed-off-by: Martin Bligh <mbligh@aracnet.com> Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com> Signed-off-by: Bob Picco <bob.picco@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 14:07:54 +07:00
[PATCH] sparsemem hotplug base Make sparse's initalization be accessible at runtime. This allows sparse mappings to be created after boot in a hotplug situation. This patch is separated from the previous one just to give an indication how much of the sparse infrastructure is *just* for hotplug memory. The section_mem_map doesn't really store a pointer. It stores something that is convenient to do some math against to get a pointer. It isn't valid to just do *section_mem_map, so I don't think it should be stored as a pointer. There are a couple of things I'd like to store about a section. First of all, the fact that it is !NULL does not mean that it is present. There could be such a combination where section_mem_map *is* NULL, but the math gets you properly to a real mem_map. So, I don't think that check is safe. Since we're storing 32-bit-aligned structures, we have a few bits in the bottom of the pointer to play with. Use one bit to encode whether there's really a mem_map there, and the other one to tell whether there's a valid section there. We need to distinguish between the two because sometimes there's a gap between when a section is discovered to be present and when we can get the mem_map for it. Signed-off-by: Dave Hansen <haveblue@us.ibm.com> Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Jack Steiner <steiner@sgi.com> Signed-off-by: Bob Picco <bob.picco@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 14:08:00 +07:00
static inline struct mem_section *__nr_to_section(unsigned long nr)
{
if (!mem_section[SECTION_NR_TO_ROOT(nr)])
return NULL;
return &mem_section[SECTION_NR_TO_ROOT(nr)][nr & SECTION_ROOT_MASK];
[PATCH] sparsemem hotplug base Make sparse's initalization be accessible at runtime. This allows sparse mappings to be created after boot in a hotplug situation. This patch is separated from the previous one just to give an indication how much of the sparse infrastructure is *just* for hotplug memory. The section_mem_map doesn't really store a pointer. It stores something that is convenient to do some math against to get a pointer. It isn't valid to just do *section_mem_map, so I don't think it should be stored as a pointer. There are a couple of things I'd like to store about a section. First of all, the fact that it is !NULL does not mean that it is present. There could be such a combination where section_mem_map *is* NULL, but the math gets you properly to a real mem_map. So, I don't think that check is safe. Since we're storing 32-bit-aligned structures, we have a few bits in the bottom of the pointer to play with. Use one bit to encode whether there's really a mem_map there, and the other one to tell whether there's a valid section there. We need to distinguish between the two because sometimes there's a gap between when a section is discovered to be present and when we can get the mem_map for it. Signed-off-by: Dave Hansen <haveblue@us.ibm.com> Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Jack Steiner <steiner@sgi.com> Signed-off-by: Bob Picco <bob.picco@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 14:08:00 +07:00
}
extern int __section_nr(struct mem_section* ms);
memory hotplug: register section/node id to free This patch set is to free pages which is allocated by bootmem for memory-hotremove. Some structures of memory management are allocated by bootmem. ex) memmap, etc. To remove memory physically, some of them must be freed according to circumstance. This patch set makes basis to free those pages, and free memmaps. Basic my idea is using remain members of struct page to remember information of users of bootmem (section number or node id). When the section is removing, kernel can confirm it. By this information, some issues can be solved. 1) When the memmap of removing section is allocated on other section by bootmem, it should/can be free. 2) When the memmap of removing section is allocated on the same section, it shouldn't be freed. Because the section has to be logical memory offlined already and all pages must be isolated against page allocater. If it is freed, page allocator may use it which will be removed physically soon. 3) When removing section has other section's memmap, kernel will be able to show easily which section should be removed before it for user. (Not implemented yet) 4) When the above case 2), the page isolation will be able to check and skip memmap's page when logical memory offline (offline_pages()). Current page isolation code fails in this case because this page is just reserved page and it can't distinguish this pages can be removed or not. But, it will be able to do by this patch. (Not implemented yet.) 5) The node information like pgdat has similar issues. But, this will be able to be solved too by this. (Not implemented yet, but, remembering node id in the pages.) Fortunately, current bootmem allocator just keeps PageReserved flags, and doesn't use any other members of page struct. The users of bootmem doesn't use them too. This patch: This is to register information which is node or section's id. Kernel can distinguish which node/section uses the pages allcated by bootmem. This is basis for hot-remove sections or nodes. Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com> Cc: Badari Pulavarty <pbadari@us.ibm.com> Cc: Yinghai Lu <yhlu.kernel@gmail.com> Cc: Yasunori Goto <y-goto@jp.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 16:13:31 +07:00
extern unsigned long usemap_size(void);
[PATCH] sparsemem hotplug base Make sparse's initalization be accessible at runtime. This allows sparse mappings to be created after boot in a hotplug situation. This patch is separated from the previous one just to give an indication how much of the sparse infrastructure is *just* for hotplug memory. The section_mem_map doesn't really store a pointer. It stores something that is convenient to do some math against to get a pointer. It isn't valid to just do *section_mem_map, so I don't think it should be stored as a pointer. There are a couple of things I'd like to store about a section. First of all, the fact that it is !NULL does not mean that it is present. There could be such a combination where section_mem_map *is* NULL, but the math gets you properly to a real mem_map. So, I don't think that check is safe. Since we're storing 32-bit-aligned structures, we have a few bits in the bottom of the pointer to play with. Use one bit to encode whether there's really a mem_map there, and the other one to tell whether there's a valid section there. We need to distinguish between the two because sometimes there's a gap between when a section is discovered to be present and when we can get the mem_map for it. Signed-off-by: Dave Hansen <haveblue@us.ibm.com> Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Jack Steiner <steiner@sgi.com> Signed-off-by: Bob Picco <bob.picco@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 14:08:00 +07:00
/*
* We use the lower bits of the mem_map pointer to store
* a little bit of information. There should be at least
* 3 bits here due to 32-bit alignment.
*/
#define SECTION_MARKED_PRESENT (1UL<<0)
#define SECTION_HAS_MEM_MAP (1UL<<1)
#define SECTION_MAP_LAST_BIT (1UL<<2)
#define SECTION_MAP_MASK (~(SECTION_MAP_LAST_BIT-1))
#define SECTION_NID_SHIFT 2
[PATCH] sparsemem hotplug base Make sparse's initalization be accessible at runtime. This allows sparse mappings to be created after boot in a hotplug situation. This patch is separated from the previous one just to give an indication how much of the sparse infrastructure is *just* for hotplug memory. The section_mem_map doesn't really store a pointer. It stores something that is convenient to do some math against to get a pointer. It isn't valid to just do *section_mem_map, so I don't think it should be stored as a pointer. There are a couple of things I'd like to store about a section. First of all, the fact that it is !NULL does not mean that it is present. There could be such a combination where section_mem_map *is* NULL, but the math gets you properly to a real mem_map. So, I don't think that check is safe. Since we're storing 32-bit-aligned structures, we have a few bits in the bottom of the pointer to play with. Use one bit to encode whether there's really a mem_map there, and the other one to tell whether there's a valid section there. We need to distinguish between the two because sometimes there's a gap between when a section is discovered to be present and when we can get the mem_map for it. Signed-off-by: Dave Hansen <haveblue@us.ibm.com> Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Jack Steiner <steiner@sgi.com> Signed-off-by: Bob Picco <bob.picco@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 14:08:00 +07:00
static inline struct page *__section_mem_map_addr(struct mem_section *section)
{
unsigned long map = section->section_mem_map;
map &= SECTION_MAP_MASK;
return (struct page *)map;
}
static inline int present_section(struct mem_section *section)
[PATCH] sparsemem hotplug base Make sparse's initalization be accessible at runtime. This allows sparse mappings to be created after boot in a hotplug situation. This patch is separated from the previous one just to give an indication how much of the sparse infrastructure is *just* for hotplug memory. The section_mem_map doesn't really store a pointer. It stores something that is convenient to do some math against to get a pointer. It isn't valid to just do *section_mem_map, so I don't think it should be stored as a pointer. There are a couple of things I'd like to store about a section. First of all, the fact that it is !NULL does not mean that it is present. There could be such a combination where section_mem_map *is* NULL, but the math gets you properly to a real mem_map. So, I don't think that check is safe. Since we're storing 32-bit-aligned structures, we have a few bits in the bottom of the pointer to play with. Use one bit to encode whether there's really a mem_map there, and the other one to tell whether there's a valid section there. We need to distinguish between the two because sometimes there's a gap between when a section is discovered to be present and when we can get the mem_map for it. Signed-off-by: Dave Hansen <haveblue@us.ibm.com> Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Jack Steiner <steiner@sgi.com> Signed-off-by: Bob Picco <bob.picco@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 14:08:00 +07:00
{
return (section && (section->section_mem_map & SECTION_MARKED_PRESENT));
[PATCH] sparsemem hotplug base Make sparse's initalization be accessible at runtime. This allows sparse mappings to be created after boot in a hotplug situation. This patch is separated from the previous one just to give an indication how much of the sparse infrastructure is *just* for hotplug memory. The section_mem_map doesn't really store a pointer. It stores something that is convenient to do some math against to get a pointer. It isn't valid to just do *section_mem_map, so I don't think it should be stored as a pointer. There are a couple of things I'd like to store about a section. First of all, the fact that it is !NULL does not mean that it is present. There could be such a combination where section_mem_map *is* NULL, but the math gets you properly to a real mem_map. So, I don't think that check is safe. Since we're storing 32-bit-aligned structures, we have a few bits in the bottom of the pointer to play with. Use one bit to encode whether there's really a mem_map there, and the other one to tell whether there's a valid section there. We need to distinguish between the two because sometimes there's a gap between when a section is discovered to be present and when we can get the mem_map for it. Signed-off-by: Dave Hansen <haveblue@us.ibm.com> Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Jack Steiner <steiner@sgi.com> Signed-off-by: Bob Picco <bob.picco@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 14:08:00 +07:00
}
static inline int present_section_nr(unsigned long nr)
{
return present_section(__nr_to_section(nr));
}
static inline int valid_section(struct mem_section *section)
[PATCH] sparsemem hotplug base Make sparse's initalization be accessible at runtime. This allows sparse mappings to be created after boot in a hotplug situation. This patch is separated from the previous one just to give an indication how much of the sparse infrastructure is *just* for hotplug memory. The section_mem_map doesn't really store a pointer. It stores something that is convenient to do some math against to get a pointer. It isn't valid to just do *section_mem_map, so I don't think it should be stored as a pointer. There are a couple of things I'd like to store about a section. First of all, the fact that it is !NULL does not mean that it is present. There could be such a combination where section_mem_map *is* NULL, but the math gets you properly to a real mem_map. So, I don't think that check is safe. Since we're storing 32-bit-aligned structures, we have a few bits in the bottom of the pointer to play with. Use one bit to encode whether there's really a mem_map there, and the other one to tell whether there's a valid section there. We need to distinguish between the two because sometimes there's a gap between when a section is discovered to be present and when we can get the mem_map for it. Signed-off-by: Dave Hansen <haveblue@us.ibm.com> Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Jack Steiner <steiner@sgi.com> Signed-off-by: Bob Picco <bob.picco@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 14:08:00 +07:00
{
return (section && (section->section_mem_map & SECTION_HAS_MEM_MAP));
[PATCH] sparsemem hotplug base Make sparse's initalization be accessible at runtime. This allows sparse mappings to be created after boot in a hotplug situation. This patch is separated from the previous one just to give an indication how much of the sparse infrastructure is *just* for hotplug memory. The section_mem_map doesn't really store a pointer. It stores something that is convenient to do some math against to get a pointer. It isn't valid to just do *section_mem_map, so I don't think it should be stored as a pointer. There are a couple of things I'd like to store about a section. First of all, the fact that it is !NULL does not mean that it is present. There could be such a combination where section_mem_map *is* NULL, but the math gets you properly to a real mem_map. So, I don't think that check is safe. Since we're storing 32-bit-aligned structures, we have a few bits in the bottom of the pointer to play with. Use one bit to encode whether there's really a mem_map there, and the other one to tell whether there's a valid section there. We need to distinguish between the two because sometimes there's a gap between when a section is discovered to be present and when we can get the mem_map for it. Signed-off-by: Dave Hansen <haveblue@us.ibm.com> Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Jack Steiner <steiner@sgi.com> Signed-off-by: Bob Picco <bob.picco@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 14:08:00 +07:00
}
static inline int valid_section_nr(unsigned long nr)
{
return valid_section(__nr_to_section(nr));
}
[PATCH] sparsemem memory model Sparsemem abstracts the use of discontiguous mem_maps[]. This kind of mem_map[] is needed by discontiguous memory machines (like in the old CONFIG_DISCONTIGMEM case) as well as memory hotplug systems. Sparsemem replaces DISCONTIGMEM when enabled, and it is hoped that it can eventually become a complete replacement. A significant advantage over DISCONTIGMEM is that it's completely separated from CONFIG_NUMA. When producing this patch, it became apparent in that NUMA and DISCONTIG are often confused. Another advantage is that sparse doesn't require each NUMA node's ranges to be contiguous. It can handle overlapping ranges between nodes with no problems, where DISCONTIGMEM currently throws away that memory. Sparsemem uses an array to provide different pfn_to_page() translations for each SECTION_SIZE area of physical memory. This is what allows the mem_map[] to be chopped up. In order to do quick pfn_to_page() operations, the section number of the page is encoded in page->flags. Part of the sparsemem infrastructure enables sharing of these bits more dynamically (at compile-time) between the page_zone() and sparsemem operations. However, on 32-bit architectures, the number of bits is quite limited, and may require growing the size of the page->flags type in certain conditions. Several things might force this to occur: a decrease in the SECTION_SIZE (if you want to hotplug smaller areas of memory), an increase in the physical address space, or an increase in the number of used page->flags. One thing to note is that, once sparsemem is present, the NUMA node information no longer needs to be stored in the page->flags. It might provide speed increases on certain platforms and will be stored there if there is room. But, if out of room, an alternate (theoretically slower) mechanism is used. This patch introduces CONFIG_FLATMEM. It is used in almost all cases where there used to be an #ifndef DISCONTIG, because SPARSEMEM and DISCONTIGMEM often have to compile out the same areas of code. Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Dave Hansen <haveblue@us.ibm.com> Signed-off-by: Martin Bligh <mbligh@aracnet.com> Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com> Signed-off-by: Bob Picco <bob.picco@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 14:07:54 +07:00
static inline struct mem_section *__pfn_to_section(unsigned long pfn)
{
[PATCH] sparsemem hotplug base Make sparse's initalization be accessible at runtime. This allows sparse mappings to be created after boot in a hotplug situation. This patch is separated from the previous one just to give an indication how much of the sparse infrastructure is *just* for hotplug memory. The section_mem_map doesn't really store a pointer. It stores something that is convenient to do some math against to get a pointer. It isn't valid to just do *section_mem_map, so I don't think it should be stored as a pointer. There are a couple of things I'd like to store about a section. First of all, the fact that it is !NULL does not mean that it is present. There could be such a combination where section_mem_map *is* NULL, but the math gets you properly to a real mem_map. So, I don't think that check is safe. Since we're storing 32-bit-aligned structures, we have a few bits in the bottom of the pointer to play with. Use one bit to encode whether there's really a mem_map there, and the other one to tell whether there's a valid section there. We need to distinguish between the two because sometimes there's a gap between when a section is discovered to be present and when we can get the mem_map for it. Signed-off-by: Dave Hansen <haveblue@us.ibm.com> Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Jack Steiner <steiner@sgi.com> Signed-off-by: Bob Picco <bob.picco@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 14:08:00 +07:00
return __nr_to_section(pfn_to_section_nr(pfn));
[PATCH] sparsemem memory model Sparsemem abstracts the use of discontiguous mem_maps[]. This kind of mem_map[] is needed by discontiguous memory machines (like in the old CONFIG_DISCONTIGMEM case) as well as memory hotplug systems. Sparsemem replaces DISCONTIGMEM when enabled, and it is hoped that it can eventually become a complete replacement. A significant advantage over DISCONTIGMEM is that it's completely separated from CONFIG_NUMA. When producing this patch, it became apparent in that NUMA and DISCONTIG are often confused. Another advantage is that sparse doesn't require each NUMA node's ranges to be contiguous. It can handle overlapping ranges between nodes with no problems, where DISCONTIGMEM currently throws away that memory. Sparsemem uses an array to provide different pfn_to_page() translations for each SECTION_SIZE area of physical memory. This is what allows the mem_map[] to be chopped up. In order to do quick pfn_to_page() operations, the section number of the page is encoded in page->flags. Part of the sparsemem infrastructure enables sharing of these bits more dynamically (at compile-time) between the page_zone() and sparsemem operations. However, on 32-bit architectures, the number of bits is quite limited, and may require growing the size of the page->flags type in certain conditions. Several things might force this to occur: a decrease in the SECTION_SIZE (if you want to hotplug smaller areas of memory), an increase in the physical address space, or an increase in the number of used page->flags. One thing to note is that, once sparsemem is present, the NUMA node information no longer needs to be stored in the page->flags. It might provide speed increases on certain platforms and will be stored there if there is room. But, if out of room, an alternate (theoretically slower) mechanism is used. This patch introduces CONFIG_FLATMEM. It is used in almost all cases where there used to be an #ifndef DISCONTIG, because SPARSEMEM and DISCONTIGMEM often have to compile out the same areas of code. Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Dave Hansen <haveblue@us.ibm.com> Signed-off-by: Martin Bligh <mbligh@aracnet.com> Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com> Signed-off-by: Bob Picco <bob.picco@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 14:07:54 +07:00
}
ARM: 6913/1: sparsemem: allow pfn_valid to be overridden when using SPARSEMEM In commit eb33575c ("[ARM] Double check memmap is actually valid with a memmap has unexpected holes V2"), a new function, memmap_valid_within, was introduced to mmzone.h so that holes in the memmap which pass pfn_valid in SPARSEMEM configurations can be detected and avoided. The fix to this problem checks that the pfn <-> page linkages are correct by calculating the page for the pfn and then checking that page_to_pfn on that page returns the original pfn. Unfortunately, in SPARSEMEM configurations, this results in reading from the page flags to determine the correct section. Since the memmap here has been freed, junk is read from memory and the check is no longer robust. In the best case, reading from /proc/pagetypeinfo will give you the wrong answer. In the worst case, you get SEGVs, Kernel OOPses and hung CPUs. Furthermore, ioremap implementations that use pfn_valid to disallow the remapping of normal memory will break. This patch allows architectures to provide their own pfn_valid function instead of using the default implementation used by sparsemem. The architecture-specific version is aware of the memmap state and will return false when passed a pfn for a freed page within a valid section. Acked-by: Mel Gorman <mgorman@suse.de> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-05-19 19:21:14 +07:00
#ifndef CONFIG_HAVE_ARCH_PFN_VALID
[PATCH] sparsemem memory model Sparsemem abstracts the use of discontiguous mem_maps[]. This kind of mem_map[] is needed by discontiguous memory machines (like in the old CONFIG_DISCONTIGMEM case) as well as memory hotplug systems. Sparsemem replaces DISCONTIGMEM when enabled, and it is hoped that it can eventually become a complete replacement. A significant advantage over DISCONTIGMEM is that it's completely separated from CONFIG_NUMA. When producing this patch, it became apparent in that NUMA and DISCONTIG are often confused. Another advantage is that sparse doesn't require each NUMA node's ranges to be contiguous. It can handle overlapping ranges between nodes with no problems, where DISCONTIGMEM currently throws away that memory. Sparsemem uses an array to provide different pfn_to_page() translations for each SECTION_SIZE area of physical memory. This is what allows the mem_map[] to be chopped up. In order to do quick pfn_to_page() operations, the section number of the page is encoded in page->flags. Part of the sparsemem infrastructure enables sharing of these bits more dynamically (at compile-time) between the page_zone() and sparsemem operations. However, on 32-bit architectures, the number of bits is quite limited, and may require growing the size of the page->flags type in certain conditions. Several things might force this to occur: a decrease in the SECTION_SIZE (if you want to hotplug smaller areas of memory), an increase in the physical address space, or an increase in the number of used page->flags. One thing to note is that, once sparsemem is present, the NUMA node information no longer needs to be stored in the page->flags. It might provide speed increases on certain platforms and will be stored there if there is room. But, if out of room, an alternate (theoretically slower) mechanism is used. This patch introduces CONFIG_FLATMEM. It is used in almost all cases where there used to be an #ifndef DISCONTIG, because SPARSEMEM and DISCONTIGMEM often have to compile out the same areas of code. Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Dave Hansen <haveblue@us.ibm.com> Signed-off-by: Martin Bligh <mbligh@aracnet.com> Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com> Signed-off-by: Bob Picco <bob.picco@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 14:07:54 +07:00
static inline int pfn_valid(unsigned long pfn)
{
if (pfn_to_section_nr(pfn) >= NR_MEM_SECTIONS)
return 0;
[PATCH] sparsemem hotplug base Make sparse's initalization be accessible at runtime. This allows sparse mappings to be created after boot in a hotplug situation. This patch is separated from the previous one just to give an indication how much of the sparse infrastructure is *just* for hotplug memory. The section_mem_map doesn't really store a pointer. It stores something that is convenient to do some math against to get a pointer. It isn't valid to just do *section_mem_map, so I don't think it should be stored as a pointer. There are a couple of things I'd like to store about a section. First of all, the fact that it is !NULL does not mean that it is present. There could be such a combination where section_mem_map *is* NULL, but the math gets you properly to a real mem_map. So, I don't think that check is safe. Since we're storing 32-bit-aligned structures, we have a few bits in the bottom of the pointer to play with. Use one bit to encode whether there's really a mem_map there, and the other one to tell whether there's a valid section there. We need to distinguish between the two because sometimes there's a gap between when a section is discovered to be present and when we can get the mem_map for it. Signed-off-by: Dave Hansen <haveblue@us.ibm.com> Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Jack Steiner <steiner@sgi.com> Signed-off-by: Bob Picco <bob.picco@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 14:08:00 +07:00
return valid_section(__nr_to_section(pfn_to_section_nr(pfn)));
[PATCH] sparsemem memory model Sparsemem abstracts the use of discontiguous mem_maps[]. This kind of mem_map[] is needed by discontiguous memory machines (like in the old CONFIG_DISCONTIGMEM case) as well as memory hotplug systems. Sparsemem replaces DISCONTIGMEM when enabled, and it is hoped that it can eventually become a complete replacement. A significant advantage over DISCONTIGMEM is that it's completely separated from CONFIG_NUMA. When producing this patch, it became apparent in that NUMA and DISCONTIG are often confused. Another advantage is that sparse doesn't require each NUMA node's ranges to be contiguous. It can handle overlapping ranges between nodes with no problems, where DISCONTIGMEM currently throws away that memory. Sparsemem uses an array to provide different pfn_to_page() translations for each SECTION_SIZE area of physical memory. This is what allows the mem_map[] to be chopped up. In order to do quick pfn_to_page() operations, the section number of the page is encoded in page->flags. Part of the sparsemem infrastructure enables sharing of these bits more dynamically (at compile-time) between the page_zone() and sparsemem operations. However, on 32-bit architectures, the number of bits is quite limited, and may require growing the size of the page->flags type in certain conditions. Several things might force this to occur: a decrease in the SECTION_SIZE (if you want to hotplug smaller areas of memory), an increase in the physical address space, or an increase in the number of used page->flags. One thing to note is that, once sparsemem is present, the NUMA node information no longer needs to be stored in the page->flags. It might provide speed increases on certain platforms and will be stored there if there is room. But, if out of room, an alternate (theoretically slower) mechanism is used. This patch introduces CONFIG_FLATMEM. It is used in almost all cases where there used to be an #ifndef DISCONTIG, because SPARSEMEM and DISCONTIGMEM often have to compile out the same areas of code. Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Dave Hansen <haveblue@us.ibm.com> Signed-off-by: Martin Bligh <mbligh@aracnet.com> Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com> Signed-off-by: Bob Picco <bob.picco@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 14:07:54 +07:00
}
ARM: 6913/1: sparsemem: allow pfn_valid to be overridden when using SPARSEMEM In commit eb33575c ("[ARM] Double check memmap is actually valid with a memmap has unexpected holes V2"), a new function, memmap_valid_within, was introduced to mmzone.h so that holes in the memmap which pass pfn_valid in SPARSEMEM configurations can be detected and avoided. The fix to this problem checks that the pfn <-> page linkages are correct by calculating the page for the pfn and then checking that page_to_pfn on that page returns the original pfn. Unfortunately, in SPARSEMEM configurations, this results in reading from the page flags to determine the correct section. Since the memmap here has been freed, junk is read from memory and the check is no longer robust. In the best case, reading from /proc/pagetypeinfo will give you the wrong answer. In the worst case, you get SEGVs, Kernel OOPses and hung CPUs. Furthermore, ioremap implementations that use pfn_valid to disallow the remapping of normal memory will break. This patch allows architectures to provide their own pfn_valid function instead of using the default implementation used by sparsemem. The architecture-specific version is aware of the memmap state and will return false when passed a pfn for a freed page within a valid section. Acked-by: Mel Gorman <mgorman@suse.de> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-05-19 19:21:14 +07:00
#endif
[PATCH] sparsemem memory model Sparsemem abstracts the use of discontiguous mem_maps[]. This kind of mem_map[] is needed by discontiguous memory machines (like in the old CONFIG_DISCONTIGMEM case) as well as memory hotplug systems. Sparsemem replaces DISCONTIGMEM when enabled, and it is hoped that it can eventually become a complete replacement. A significant advantage over DISCONTIGMEM is that it's completely separated from CONFIG_NUMA. When producing this patch, it became apparent in that NUMA and DISCONTIG are often confused. Another advantage is that sparse doesn't require each NUMA node's ranges to be contiguous. It can handle overlapping ranges between nodes with no problems, where DISCONTIGMEM currently throws away that memory. Sparsemem uses an array to provide different pfn_to_page() translations for each SECTION_SIZE area of physical memory. This is what allows the mem_map[] to be chopped up. In order to do quick pfn_to_page() operations, the section number of the page is encoded in page->flags. Part of the sparsemem infrastructure enables sharing of these bits more dynamically (at compile-time) between the page_zone() and sparsemem operations. However, on 32-bit architectures, the number of bits is quite limited, and may require growing the size of the page->flags type in certain conditions. Several things might force this to occur: a decrease in the SECTION_SIZE (if you want to hotplug smaller areas of memory), an increase in the physical address space, or an increase in the number of used page->flags. One thing to note is that, once sparsemem is present, the NUMA node information no longer needs to be stored in the page->flags. It might provide speed increases on certain platforms and will be stored there if there is room. But, if out of room, an alternate (theoretically slower) mechanism is used. This patch introduces CONFIG_FLATMEM. It is used in almost all cases where there used to be an #ifndef DISCONTIG, because SPARSEMEM and DISCONTIGMEM often have to compile out the same areas of code. Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Dave Hansen <haveblue@us.ibm.com> Signed-off-by: Martin Bligh <mbligh@aracnet.com> Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com> Signed-off-by: Bob Picco <bob.picco@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 14:07:54 +07:00
static inline int pfn_present(unsigned long pfn)
{
if (pfn_to_section_nr(pfn) >= NR_MEM_SECTIONS)
return 0;
return present_section(__nr_to_section(pfn_to_section_nr(pfn)));
}
[PATCH] sparsemem memory model Sparsemem abstracts the use of discontiguous mem_maps[]. This kind of mem_map[] is needed by discontiguous memory machines (like in the old CONFIG_DISCONTIGMEM case) as well as memory hotplug systems. Sparsemem replaces DISCONTIGMEM when enabled, and it is hoped that it can eventually become a complete replacement. A significant advantage over DISCONTIGMEM is that it's completely separated from CONFIG_NUMA. When producing this patch, it became apparent in that NUMA and DISCONTIG are often confused. Another advantage is that sparse doesn't require each NUMA node's ranges to be contiguous. It can handle overlapping ranges between nodes with no problems, where DISCONTIGMEM currently throws away that memory. Sparsemem uses an array to provide different pfn_to_page() translations for each SECTION_SIZE area of physical memory. This is what allows the mem_map[] to be chopped up. In order to do quick pfn_to_page() operations, the section number of the page is encoded in page->flags. Part of the sparsemem infrastructure enables sharing of these bits more dynamically (at compile-time) between the page_zone() and sparsemem operations. However, on 32-bit architectures, the number of bits is quite limited, and may require growing the size of the page->flags type in certain conditions. Several things might force this to occur: a decrease in the SECTION_SIZE (if you want to hotplug smaller areas of memory), an increase in the physical address space, or an increase in the number of used page->flags. One thing to note is that, once sparsemem is present, the NUMA node information no longer needs to be stored in the page->flags. It might provide speed increases on certain platforms and will be stored there if there is room. But, if out of room, an alternate (theoretically slower) mechanism is used. This patch introduces CONFIG_FLATMEM. It is used in almost all cases where there used to be an #ifndef DISCONTIG, because SPARSEMEM and DISCONTIGMEM often have to compile out the same areas of code. Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Dave Hansen <haveblue@us.ibm.com> Signed-off-by: Martin Bligh <mbligh@aracnet.com> Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com> Signed-off-by: Bob Picco <bob.picco@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 14:07:54 +07:00
/*
* These are _only_ used during initialisation, therefore they
* can use __initdata ... They could have names to indicate
* this restriction.
*/
#ifdef CONFIG_NUMA
#define pfn_to_nid(pfn) \
({ \
unsigned long __pfn_to_nid_pfn = (pfn); \
page_to_nid(pfn_to_page(__pfn_to_nid_pfn)); \
})
[PATCH] flatmem split out memory model There are three places we define pfn_to_nid(). Two in linux/mmzone.h and one in asm/mmzone.h. These in essence represent the three memory models. The definition in linux/mmzone.h under !NEED_MULTIPLE_NODES is both the FLATMEM definition and the optimisation for single NUMA nodes; the one under SPARSEMEM is the NUMA sparsemem one; the one in asm/mmzone.h under DISCONTIGMEM is the discontigmem one. This is not in the least bit obvious, particularly the connection between the non-NUMA optimisations and the memory models. Two patches: flatmem-split-out-memory-model: simplifies the selection of pfn_to_nid() implementations. The selection is based primarily off the memory model selected. Optimisations for non-NUMA are applied where needed. sparse-provide-pfn_to_nid: implement pfn_to_nid() for SPARSEMEM This patch: pfn_to_nid is memory model specific The pfn_to_nid() call is memory model specific. It represents the locality identifier for the memory passed. Classically this would be a NUMA node, but not a chunk of memory under DISCONTIGMEM. The SPARSEMEM and FLATMEM memory model non-NUMA versions of pfn_to_nid() are folded together under NEED_MULTIPLE_NODES, while DISCONTIGMEM has its own optimisation. This is all very confusing. This patch splits out each implementation of pfn_to_nid() so that we can see them and the optimisations to each. Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 15:10:53 +07:00
#else
#define pfn_to_nid(pfn) (0)
[PATCH] sparsemem memory model Sparsemem abstracts the use of discontiguous mem_maps[]. This kind of mem_map[] is needed by discontiguous memory machines (like in the old CONFIG_DISCONTIGMEM case) as well as memory hotplug systems. Sparsemem replaces DISCONTIGMEM when enabled, and it is hoped that it can eventually become a complete replacement. A significant advantage over DISCONTIGMEM is that it's completely separated from CONFIG_NUMA. When producing this patch, it became apparent in that NUMA and DISCONTIG are often confused. Another advantage is that sparse doesn't require each NUMA node's ranges to be contiguous. It can handle overlapping ranges between nodes with no problems, where DISCONTIGMEM currently throws away that memory. Sparsemem uses an array to provide different pfn_to_page() translations for each SECTION_SIZE area of physical memory. This is what allows the mem_map[] to be chopped up. In order to do quick pfn_to_page() operations, the section number of the page is encoded in page->flags. Part of the sparsemem infrastructure enables sharing of these bits more dynamically (at compile-time) between the page_zone() and sparsemem operations. However, on 32-bit architectures, the number of bits is quite limited, and may require growing the size of the page->flags type in certain conditions. Several things might force this to occur: a decrease in the SECTION_SIZE (if you want to hotplug smaller areas of memory), an increase in the physical address space, or an increase in the number of used page->flags. One thing to note is that, once sparsemem is present, the NUMA node information no longer needs to be stored in the page->flags. It might provide speed increases on certain platforms and will be stored there if there is room. But, if out of room, an alternate (theoretically slower) mechanism is used. This patch introduces CONFIG_FLATMEM. It is used in almost all cases where there used to be an #ifndef DISCONTIG, because SPARSEMEM and DISCONTIGMEM often have to compile out the same areas of code. Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Dave Hansen <haveblue@us.ibm.com> Signed-off-by: Martin Bligh <mbligh@aracnet.com> Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com> Signed-off-by: Bob Picco <bob.picco@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 14:07:54 +07:00
#endif
#define early_pfn_valid(pfn) pfn_valid(pfn)
void sparse_init(void);
#else
#define sparse_init() do {} while (0)
#define sparse_index_init(_sec, _nid) do {} while (0)
[PATCH] sparsemem memory model Sparsemem abstracts the use of discontiguous mem_maps[]. This kind of mem_map[] is needed by discontiguous memory machines (like in the old CONFIG_DISCONTIGMEM case) as well as memory hotplug systems. Sparsemem replaces DISCONTIGMEM when enabled, and it is hoped that it can eventually become a complete replacement. A significant advantage over DISCONTIGMEM is that it's completely separated from CONFIG_NUMA. When producing this patch, it became apparent in that NUMA and DISCONTIG are often confused. Another advantage is that sparse doesn't require each NUMA node's ranges to be contiguous. It can handle overlapping ranges between nodes with no problems, where DISCONTIGMEM currently throws away that memory. Sparsemem uses an array to provide different pfn_to_page() translations for each SECTION_SIZE area of physical memory. This is what allows the mem_map[] to be chopped up. In order to do quick pfn_to_page() operations, the section number of the page is encoded in page->flags. Part of the sparsemem infrastructure enables sharing of these bits more dynamically (at compile-time) between the page_zone() and sparsemem operations. However, on 32-bit architectures, the number of bits is quite limited, and may require growing the size of the page->flags type in certain conditions. Several things might force this to occur: a decrease in the SECTION_SIZE (if you want to hotplug smaller areas of memory), an increase in the physical address space, or an increase in the number of used page->flags. One thing to note is that, once sparsemem is present, the NUMA node information no longer needs to be stored in the page->flags. It might provide speed increases on certain platforms and will be stored there if there is room. But, if out of room, an alternate (theoretically slower) mechanism is used. This patch introduces CONFIG_FLATMEM. It is used in almost all cases where there used to be an #ifndef DISCONTIG, because SPARSEMEM and DISCONTIGMEM often have to compile out the same areas of code. Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Dave Hansen <haveblue@us.ibm.com> Signed-off-by: Martin Bligh <mbligh@aracnet.com> Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com> Signed-off-by: Bob Picco <bob.picco@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 14:07:54 +07:00
#endif /* CONFIG_SPARSEMEM */
#ifdef CONFIG_NODES_SPAN_OTHER_NODES
bool early_pfn_in_nid(unsigned long pfn, int nid);
#else
#define early_pfn_in_nid(pfn, nid) (1)
#endif
[PATCH] sparsemem memory model Sparsemem abstracts the use of discontiguous mem_maps[]. This kind of mem_map[] is needed by discontiguous memory machines (like in the old CONFIG_DISCONTIGMEM case) as well as memory hotplug systems. Sparsemem replaces DISCONTIGMEM when enabled, and it is hoped that it can eventually become a complete replacement. A significant advantage over DISCONTIGMEM is that it's completely separated from CONFIG_NUMA. When producing this patch, it became apparent in that NUMA and DISCONTIG are often confused. Another advantage is that sparse doesn't require each NUMA node's ranges to be contiguous. It can handle overlapping ranges between nodes with no problems, where DISCONTIGMEM currently throws away that memory. Sparsemem uses an array to provide different pfn_to_page() translations for each SECTION_SIZE area of physical memory. This is what allows the mem_map[] to be chopped up. In order to do quick pfn_to_page() operations, the section number of the page is encoded in page->flags. Part of the sparsemem infrastructure enables sharing of these bits more dynamically (at compile-time) between the page_zone() and sparsemem operations. However, on 32-bit architectures, the number of bits is quite limited, and may require growing the size of the page->flags type in certain conditions. Several things might force this to occur: a decrease in the SECTION_SIZE (if you want to hotplug smaller areas of memory), an increase in the physical address space, or an increase in the number of used page->flags. One thing to note is that, once sparsemem is present, the NUMA node information no longer needs to be stored in the page->flags. It might provide speed increases on certain platforms and will be stored there if there is room. But, if out of room, an alternate (theoretically slower) mechanism is used. This patch introduces CONFIG_FLATMEM. It is used in almost all cases where there used to be an #ifndef DISCONTIG, because SPARSEMEM and DISCONTIGMEM often have to compile out the same areas of code. Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Dave Hansen <haveblue@us.ibm.com> Signed-off-by: Martin Bligh <mbligh@aracnet.com> Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com> Signed-off-by: Bob Picco <bob.picco@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 14:07:54 +07:00
#ifndef early_pfn_valid
#define early_pfn_valid(pfn) (1)
#endif
void memory_present(int nid, unsigned long start, unsigned long end);
unsigned long __init node_memmap_size_bytes(int, unsigned long, unsigned long);
/*
* If it is possible to have holes within a MAX_ORDER_NR_PAGES, then we
* need to check pfn validility within that MAX_ORDER_NR_PAGES block.
* pfn_valid_within() should be used in this case; we optimise this away
* when we have no holes within a MAX_ORDER_NR_PAGES block.
*/
#ifdef CONFIG_HOLES_IN_ZONE
#define pfn_valid_within(pfn) pfn_valid(pfn)
#else
#define pfn_valid_within(pfn) (1)
#endif
[ARM] Double check memmap is actually valid with a memmap has unexpected holes V2 pfn_valid() is meant to be able to tell if a given PFN has valid memmap associated with it or not. In FLATMEM, it is expected that holes always have valid memmap as long as there is valid PFNs either side of the hole. In SPARSEMEM, it is assumed that a valid section has a memmap for the entire section. However, ARM and maybe other embedded architectures in the future free memmap backing holes to save memory on the assumption the memmap is never used. The page_zone linkages are then broken even though pfn_valid() returns true. A walker of the full memmap must then do this additional check to ensure the memmap they are looking at is sane by making sure the zone and PFN linkages are still valid. This is expensive, but walkers of the full memmap are extremely rare. This was caught before for FLATMEM and hacked around but it hits again for SPARSEMEM because the page_zone linkages can look ok where the PFN linkages are totally screwed. This looks like a hatchet job but the reality is that any clean solution would end up consumning all the memory saved by punching these unexpected holes in the memmap. For example, we tried marking the memmap within the section invalid but the section size exceeds the size of the hole in most cases so pfn_valid() starts returning false where valid memmap exists. Shrinking the size of the section would increase memory consumption offsetting the gains. This patch identifies when an architecture is punching unexpected holes in the memmap that the memory model cannot automatically detect and sets ARCH_HAS_HOLES_MEMORYMODEL. At the moment, this is restricted to EP93xx which is the model sub-architecture this has been reported on but may expand later. When set, walkers of the full memmap must call memmap_valid_within() for each PFN and passing in what it expects the page and zone to be for that PFN. If it finds the linkages to be broken, it assumes the memmap is invalid for that PFN. Signed-off-by: Mel Gorman <mel@csn.ul.ie> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-05-13 23:34:48 +07:00
#ifdef CONFIG_ARCH_HAS_HOLES_MEMORYMODEL
/*
* pfn_valid() is meant to be able to tell if a given PFN has valid memmap
* associated with it or not. In FLATMEM, it is expected that holes always
* have valid memmap as long as there is valid PFNs either side of the hole.
* In SPARSEMEM, it is assumed that a valid section has a memmap for the
* entire section.
*
* However, an ARM, and maybe other embedded architectures in the future
* free memmap backing holes to save memory on the assumption the memmap is
* never used. The page_zone linkages are then broken even though pfn_valid()
* returns true. A walker of the full memmap must then do this additional
* check to ensure the memmap they are looking at is sane by making sure
* the zone and PFN linkages are still valid. This is expensive, but walkers
* of the full memmap are extremely rare.
*/
int memmap_valid_within(unsigned long pfn,
struct page *page, struct zone *zone);
#else
static inline int memmap_valid_within(unsigned long pfn,
struct page *page, struct zone *zone)
{
return 1;
}
#endif /* CONFIG_ARCH_HAS_HOLES_MEMORYMODEL */
#endif /* !__GENERATING_BOUNDS.H */
#endif /* !__ASSEMBLY__ */
#endif /* _LINUX_MMZONE_H */