AuxXxilium/linux_dsm_epyc7002
1
0
Fork 0
mirror of https://github.com/AuxXxilium/linux_dsm_epyc7002.git synced 2024-11-26 09:00:55 +07:00
Code Issues Actions Packages Projects Releases Wiki Activity
639b91a364
linux_dsm_epyc7002/arch/arm/mach-pxa/mfp-pxa2xx.c

390 lines
8.3 KiB
C
Raw Normal View History

[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 16:16:29 +07:00
/*
* linux/arch/arm/mach-pxa/mfp-pxa2xx.c
*
* PXA2xx pin mux configuration support
*
* The GPIOs on PXA2xx can be configured as one of many alternate
* functions, this is by concept samilar to the MFP configuration
* on PXA3xx, what's more important, the low power pin state and
* wakeup detection are also supported by the same framework.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/sysdev.h>
[ARM] pxa: move GPIO register definitions into <mach/gpio.h> This makes gpio.c fully independent of pxa-regs.h (except for the virtual address of the registers). Signed-off-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: Eric Miao <eric.miao@marvell.com>
2009-01-06 17:29:01 +07:00
#include <mach/gpio.h>
[ARM] Move include/asm-arm/arch-* to arch/arm/*/include/mach This just leaves include/asm-arm/plat-* to deal with. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-08-05 22:14:15 +07:00
#include <mach/pxa2xx-regs.h>
#include <mach/mfp-pxa2xx.h>
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 16:16:29 +07:00
#include "generic.h"
[ARM] pxa: better MFP low power state support for pxa25x/pxa27x When configured as a specific low power state: MFP_LPM_DRIVE_LOW, MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during low power mode shall be re-configured as output (if they are not configured so), thus the PGSRx bits can output. Create an additional low power values GPDR registers, and properly save/restore the GAFR + GPDR registers when doing suspend/resume. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-03 17:06:34 +07:00
#define PGSR(x) __REG2(0x40F00020, (x) << 2)
#define __GAFR(u, x) __REG2((u) ? 0x40E00058 : 0x40E00054, (x) << 3)
#define GAFR_L(x) __GAFR(0, x)
#define GAFR_U(x) __GAFR(1, x)
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 16:16:29 +07:00
#define PWER_WE35 (1 << 24)
[ARM] pxa: allow dynamic enable/disable of GPIO wakeup for pxa{25x,27x} Changes include: 1. rename MFP_LPM_WAKEUP_ENABLE into MFP_LPM_CAN_WAKEUP to indicate the board capability of this pin to wakeup the system 2. add gpio_set_wake() and keypad_set_wake() to allow dynamically enable/disable wakeup from GPIOs and keypad GPIO * these functions are currently kept in mfp-pxa2xx.c due to their dependency to the MFP configuration 3. pxa2xx_mfp_config() only gives early warning if MFP_LPM_CAN_WAKEUP is set on incorrect pins So that the GPIO's wakeup capability is now decided by the following: a) processor's capability: (only those GPIOs which have dedicated bits within PWER/PRER/PFER can wakeup the system), this is initialized by pxa{25x,27x}_init_mfp() b) board design decides: - whether the pin is designed to wakeup the system (some of the GPIOs are configured as other functions, which is not intended to be a wakeup source), by OR'ing the pin config with MFP_LPM_CAN_WAKEUP - which edge the pin is designed to wakeup the system, this may depends on external peripherals/connections, which is totally board specific; this is indicated by MFP_LPM_EDGE_* c) the corresponding device's (most likely the gpio_keys.c) wakeup attribute: Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-11 08:46:28 +07:00
struct gpio_desc {
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 16:16:29 +07:00
unsigned valid : 1;
unsigned can_wakeup : 1;
unsigned keypad_gpio : 1;
[ARM] pxa: add support for additional GPIOs on PXA26x Original patch from Marek Vasut, the problems with PXA26x are: 1. there are additional 4 GPIOs 86,87,88,89 have their direction bits inverted in GPDR2, as well as their alternate function bits being '1' for their GPIO functionality in GAFRx 2. there is no easy way to decide if the processor is a pxa26x or a pxa250/pxa255 at run-time, so the assumption here is the pxa26x will be treated as one of the pxa25x variants, and board code should have a better knowledge of the processor it is featured Introduce pxa26x_init_irq() for the second purpose, and treat the additional GPIOs > 85 on PXA25x specially. Kconfig option CONFIG_CPU_PXA26x is introduced to optimize the code a bit when PXA26x support isn't needed. Board config options have to select this to enable the support for PXA26x. __gpio_is_inverted() will be optimized way when CONFIG_CPU_PXA26x isn't selected. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-11-26 17:12:04 +07:00
unsigned dir_inverted : 1;
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 16:16:29 +07:00
unsigned int mask; /* bit mask in PWER or PKWR */
[ARM] pxa: add muxed gpio wakeup sources on pxa2xx architectures PXA SoC have several GPIOs muxed on only one wakeup source. Add support for these wakeup sources which were missing in mfp core support. Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-11-14 05:30:00 +07:00
unsigned int mux_mask; /* bit mask of muxed gpio bits, 0 if no mux */
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 16:16:29 +07:00
unsigned long config;
[ARM] pxa: allow dynamic enable/disable of GPIO wakeup for pxa{25x,27x} Changes include: 1. rename MFP_LPM_WAKEUP_ENABLE into MFP_LPM_CAN_WAKEUP to indicate the board capability of this pin to wakeup the system 2. add gpio_set_wake() and keypad_set_wake() to allow dynamically enable/disable wakeup from GPIOs and keypad GPIO * these functions are currently kept in mfp-pxa2xx.c due to their dependency to the MFP configuration 3. pxa2xx_mfp_config() only gives early warning if MFP_LPM_CAN_WAKEUP is set on incorrect pins So that the GPIO's wakeup capability is now decided by the following: a) processor's capability: (only those GPIOs which have dedicated bits within PWER/PRER/PFER can wakeup the system), this is initialized by pxa{25x,27x}_init_mfp() b) board design decides: - whether the pin is designed to wakeup the system (some of the GPIOs are configured as other functions, which is not intended to be a wakeup source), by OR'ing the pin config with MFP_LPM_CAN_WAKEUP - which edge the pin is designed to wakeup the system, this may depends on external peripherals/connections, which is totally board specific; this is indicated by MFP_LPM_EDGE_* c) the corresponding device's (most likely the gpio_keys.c) wakeup attribute: Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-11 08:46:28 +07:00
};
static struct gpio_desc gpio_desc[MFP_PIN_GPIO127 + 1];
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 16:16:29 +07:00
[ARM] pxa: better MFP low power state support for pxa25x/pxa27x When configured as a specific low power state: MFP_LPM_DRIVE_LOW, MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during low power mode shall be re-configured as output (if they are not configured so), thus the PGSRx bits can output. Create an additional low power values GPDR registers, and properly save/restore the GAFR + GPDR registers when doing suspend/resume. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-03 17:06:34 +07:00
static unsigned long gpdr_lpm[4];
[ARM] pxa: add pxa2xx_mfp_set_lpm() to facilitate low power state change Some boards want to change low power state of pins on-the-fly, this function helps to facilitate that operation instead of switching back-n-forth between two configurations with pxa2xx_mfp_config(). Signed-off-by: Eric Miao <eric.miao@marvell.com> Tested-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-06-16 08:47:47 +07:00
[ARM] pxa: allow dynamic enable/disable of GPIO wakeup for pxa{25x,27x} Changes include: 1. rename MFP_LPM_WAKEUP_ENABLE into MFP_LPM_CAN_WAKEUP to indicate the board capability of this pin to wakeup the system 2. add gpio_set_wake() and keypad_set_wake() to allow dynamically enable/disable wakeup from GPIOs and keypad GPIO * these functions are currently kept in mfp-pxa2xx.c due to their dependency to the MFP configuration 3. pxa2xx_mfp_config() only gives early warning if MFP_LPM_CAN_WAKEUP is set on incorrect pins So that the GPIO's wakeup capability is now decided by the following: a) processor's capability: (only those GPIOs which have dedicated bits within PWER/PRER/PFER can wakeup the system), this is initialized by pxa{25x,27x}_init_mfp() b) board design decides: - whether the pin is designed to wakeup the system (some of the GPIOs are configured as other functions, which is not intended to be a wakeup source), by OR'ing the pin config with MFP_LPM_CAN_WAKEUP - which edge the pin is designed to wakeup the system, this may depends on external peripherals/connections, which is totally board specific; this is indicated by MFP_LPM_EDGE_* c) the corresponding device's (most likely the gpio_keys.c) wakeup attribute: Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-11 08:46:28 +07:00
static int __mfp_config_gpio(unsigned gpio, unsigned long c)
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 16:16:29 +07:00
{
unsigned long gafr, mask = GPIO_bit(gpio);
[ARM] pxa: better MFP low power state support for pxa25x/pxa27x When configured as a specific low power state: MFP_LPM_DRIVE_LOW, MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during low power mode shall be re-configured as output (if they are not configured so), thus the PGSRx bits can output. Create an additional low power values GPDR registers, and properly save/restore the GAFR + GPDR registers when doing suspend/resume. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-03 17:06:34 +07:00
int bank = gpio_to_bank(gpio);
int uorl = !!(gpio & 0x10); /* GAFRx_U or GAFRx_L ? */
int shft = (gpio & 0xf) << 1;
int fn = MFP_AF(c);
[ARM] pxa: add support for additional GPIOs on PXA26x Original patch from Marek Vasut, the problems with PXA26x are: 1. there are additional 4 GPIOs 86,87,88,89 have their direction bits inverted in GPDR2, as well as their alternate function bits being '1' for their GPIO functionality in GAFRx 2. there is no easy way to decide if the processor is a pxa26x or a pxa250/pxa255 at run-time, so the assumption here is the pxa26x will be treated as one of the pxa25x variants, and board code should have a better knowledge of the processor it is featured Introduce pxa26x_init_irq() for the second purpose, and treat the additional GPIOs > 85 on PXA25x specially. Kconfig option CONFIG_CPU_PXA26x is introduced to optimize the code a bit when PXA26x support isn't needed. Board config options have to select this to enable the support for PXA26x. __gpio_is_inverted() will be optimized way when CONFIG_CPU_PXA26x isn't selected. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-11-26 17:12:04 +07:00
int is_out = (c & MFP_DIR_OUT) ? 1 : 0;
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 16:16:29 +07:00
if (fn > 3)
return -EINVAL;
[ARM] pxa: better MFP low power state support for pxa25x/pxa27x When configured as a specific low power state: MFP_LPM_DRIVE_LOW, MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during low power mode shall be re-configured as output (if they are not configured so), thus the PGSRx bits can output. Create an additional low power values GPDR registers, and properly save/restore the GAFR + GPDR registers when doing suspend/resume. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-03 17:06:34 +07:00
/* alternate function and direction at run-time */
gafr = (uorl == 0) ? GAFR_L(bank) : GAFR_U(bank);
gafr = (gafr & ~(0x3 << shft)) | (fn << shft);
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 16:16:29 +07:00
[ARM] pxa: better MFP low power state support for pxa25x/pxa27x When configured as a specific low power state: MFP_LPM_DRIVE_LOW, MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during low power mode shall be re-configured as output (if they are not configured so), thus the PGSRx bits can output. Create an additional low power values GPDR registers, and properly save/restore the GAFR + GPDR registers when doing suspend/resume. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-03 17:06:34 +07:00
if (uorl == 0)
GAFR_L(bank) = gafr;
else
GAFR_U(bank) = gafr;
[ARM] pxa: add support for additional GPIOs on PXA26x Original patch from Marek Vasut, the problems with PXA26x are: 1. there are additional 4 GPIOs 86,87,88,89 have their direction bits inverted in GPDR2, as well as their alternate function bits being '1' for their GPIO functionality in GAFRx 2. there is no easy way to decide if the processor is a pxa26x or a pxa250/pxa255 at run-time, so the assumption here is the pxa26x will be treated as one of the pxa25x variants, and board code should have a better knowledge of the processor it is featured Introduce pxa26x_init_irq() for the second purpose, and treat the additional GPIOs > 85 on PXA25x specially. Kconfig option CONFIG_CPU_PXA26x is introduced to optimize the code a bit when PXA26x support isn't needed. Board config options have to select this to enable the support for PXA26x. __gpio_is_inverted() will be optimized way when CONFIG_CPU_PXA26x isn't selected. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-11-26 17:12:04 +07:00
if (is_out ^ gpio_desc[gpio].dir_inverted)
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 16:16:29 +07:00
GPDR(gpio) |= mask;
else
GPDR(gpio) &= ~mask;
[ARM] pxa: better MFP low power state support for pxa25x/pxa27x When configured as a specific low power state: MFP_LPM_DRIVE_LOW, MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during low power mode shall be re-configured as output (if they are not configured so), thus the PGSRx bits can output. Create an additional low power values GPDR registers, and properly save/restore the GAFR + GPDR registers when doing suspend/resume. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-03 17:06:34 +07:00
/* alternate function and direction at low power mode */
switch (c & MFP_LPM_STATE_MASK) {
case MFP_LPM_DRIVE_HIGH:
PGSR(bank) |= mask;
[ARM] pxa: add support for additional GPIOs on PXA26x Original patch from Marek Vasut, the problems with PXA26x are: 1. there are additional 4 GPIOs 86,87,88,89 have their direction bits inverted in GPDR2, as well as their alternate function bits being '1' for their GPIO functionality in GAFRx 2. there is no easy way to decide if the processor is a pxa26x or a pxa250/pxa255 at run-time, so the assumption here is the pxa26x will be treated as one of the pxa25x variants, and board code should have a better knowledge of the processor it is featured Introduce pxa26x_init_irq() for the second purpose, and treat the additional GPIOs > 85 on PXA25x specially. Kconfig option CONFIG_CPU_PXA26x is introduced to optimize the code a bit when PXA26x support isn't needed. Board config options have to select this to enable the support for PXA26x. __gpio_is_inverted() will be optimized way when CONFIG_CPU_PXA26x isn't selected. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-11-26 17:12:04 +07:00
is_out = 1;
[ARM] pxa: better MFP low power state support for pxa25x/pxa27x When configured as a specific low power state: MFP_LPM_DRIVE_LOW, MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during low power mode shall be re-configured as output (if they are not configured so), thus the PGSRx bits can output. Create an additional low power values GPDR registers, and properly save/restore the GAFR + GPDR registers when doing suspend/resume. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-03 17:06:34 +07:00
break;
case MFP_LPM_DRIVE_LOW:
PGSR(bank) &= ~mask;
[ARM] pxa: add support for additional GPIOs on PXA26x Original patch from Marek Vasut, the problems with PXA26x are: 1. there are additional 4 GPIOs 86,87,88,89 have their direction bits inverted in GPDR2, as well as their alternate function bits being '1' for their GPIO functionality in GAFRx 2. there is no easy way to decide if the processor is a pxa26x or a pxa250/pxa255 at run-time, so the assumption here is the pxa26x will be treated as one of the pxa25x variants, and board code should have a better knowledge of the processor it is featured Introduce pxa26x_init_irq() for the second purpose, and treat the additional GPIOs > 85 on PXA25x specially. Kconfig option CONFIG_CPU_PXA26x is introduced to optimize the code a bit when PXA26x support isn't needed. Board config options have to select this to enable the support for PXA26x. __gpio_is_inverted() will be optimized way when CONFIG_CPU_PXA26x isn't selected. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-11-26 17:12:04 +07:00
is_out = 1;
[ARM] pxa: better MFP low power state support for pxa25x/pxa27x When configured as a specific low power state: MFP_LPM_DRIVE_LOW, MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during low power mode shall be re-configured as output (if they are not configured so), thus the PGSRx bits can output. Create an additional low power values GPDR registers, and properly save/restore the GAFR + GPDR registers when doing suspend/resume. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-03 17:06:34 +07:00
break;
case MFP_LPM_DEFAULT:
break;
default:
/* warning and fall through, treat as MFP_LPM_DEFAULT */
pr_warning("%s: GPIO%d: unsupported low power mode\n",
__func__, gpio);
break;
}
[ARM] pxa: add support for additional GPIOs on PXA26x Original patch from Marek Vasut, the problems with PXA26x are: 1. there are additional 4 GPIOs 86,87,88,89 have their direction bits inverted in GPDR2, as well as their alternate function bits being '1' for their GPIO functionality in GAFRx 2. there is no easy way to decide if the processor is a pxa26x or a pxa250/pxa255 at run-time, so the assumption here is the pxa26x will be treated as one of the pxa25x variants, and board code should have a better knowledge of the processor it is featured Introduce pxa26x_init_irq() for the second purpose, and treat the additional GPIOs > 85 on PXA25x specially. Kconfig option CONFIG_CPU_PXA26x is introduced to optimize the code a bit when PXA26x support isn't needed. Board config options have to select this to enable the support for PXA26x. __gpio_is_inverted() will be optimized way when CONFIG_CPU_PXA26x isn't selected. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-11-26 17:12:04 +07:00
if (is_out ^ gpio_desc[gpio].dir_inverted)
[ARM] pxa: better MFP low power state support for pxa25x/pxa27x When configured as a specific low power state: MFP_LPM_DRIVE_LOW, MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during low power mode shall be re-configured as output (if they are not configured so), thus the PGSRx bits can output. Create an additional low power values GPDR registers, and properly save/restore the GAFR + GPDR registers when doing suspend/resume. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-03 17:06:34 +07:00
gpdr_lpm[bank] |= mask;
else
gpdr_lpm[bank] &= ~mask;
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 16:16:29 +07:00
[ARM] pxa: allow dynamic enable/disable of GPIO wakeup for pxa{25x,27x} Changes include: 1. rename MFP_LPM_WAKEUP_ENABLE into MFP_LPM_CAN_WAKEUP to indicate the board capability of this pin to wakeup the system 2. add gpio_set_wake() and keypad_set_wake() to allow dynamically enable/disable wakeup from GPIOs and keypad GPIO * these functions are currently kept in mfp-pxa2xx.c due to their dependency to the MFP configuration 3. pxa2xx_mfp_config() only gives early warning if MFP_LPM_CAN_WAKEUP is set on incorrect pins So that the GPIO's wakeup capability is now decided by the following: a) processor's capability: (only those GPIOs which have dedicated bits within PWER/PRER/PFER can wakeup the system), this is initialized by pxa{25x,27x}_init_mfp() b) board design decides: - whether the pin is designed to wakeup the system (some of the GPIOs are configured as other functions, which is not intended to be a wakeup source), by OR'ing the pin config with MFP_LPM_CAN_WAKEUP - which edge the pin is designed to wakeup the system, this may depends on external peripherals/connections, which is totally board specific; this is indicated by MFP_LPM_EDGE_* c) the corresponding device's (most likely the gpio_keys.c) wakeup attribute: Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-11 08:46:28 +07:00
/* give early warning if MFP_LPM_CAN_WAKEUP is set on the
* configurations of those pins not able to wakeup
*/
if ((c & MFP_LPM_CAN_WAKEUP) && !gpio_desc[gpio].can_wakeup) {
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 16:16:29 +07:00
pr_warning("%s: GPIO%d unable to wakeup\n",
__func__, gpio);
return -EINVAL;
}
[ARM] pxa: add support for additional GPIOs on PXA26x Original patch from Marek Vasut, the problems with PXA26x are: 1. there are additional 4 GPIOs 86,87,88,89 have their direction bits inverted in GPDR2, as well as their alternate function bits being '1' for their GPIO functionality in GAFRx 2. there is no easy way to decide if the processor is a pxa26x or a pxa250/pxa255 at run-time, so the assumption here is the pxa26x will be treated as one of the pxa25x variants, and board code should have a better knowledge of the processor it is featured Introduce pxa26x_init_irq() for the second purpose, and treat the additional GPIOs > 85 on PXA25x specially. Kconfig option CONFIG_CPU_PXA26x is introduced to optimize the code a bit when PXA26x support isn't needed. Board config options have to select this to enable the support for PXA26x. __gpio_is_inverted() will be optimized way when CONFIG_CPU_PXA26x isn't selected. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-11-26 17:12:04 +07:00
if ((c & MFP_LPM_CAN_WAKEUP) && is_out) {
[ARM] pxa: allow dynamic enable/disable of GPIO wakeup for pxa{25x,27x} Changes include: 1. rename MFP_LPM_WAKEUP_ENABLE into MFP_LPM_CAN_WAKEUP to indicate the board capability of this pin to wakeup the system 2. add gpio_set_wake() and keypad_set_wake() to allow dynamically enable/disable wakeup from GPIOs and keypad GPIO * these functions are currently kept in mfp-pxa2xx.c due to their dependency to the MFP configuration 3. pxa2xx_mfp_config() only gives early warning if MFP_LPM_CAN_WAKEUP is set on incorrect pins So that the GPIO's wakeup capability is now decided by the following: a) processor's capability: (only those GPIOs which have dedicated bits within PWER/PRER/PFER can wakeup the system), this is initialized by pxa{25x,27x}_init_mfp() b) board design decides: - whether the pin is designed to wakeup the system (some of the GPIOs are configured as other functions, which is not intended to be a wakeup source), by OR'ing the pin config with MFP_LPM_CAN_WAKEUP - which edge the pin is designed to wakeup the system, this may depends on external peripherals/connections, which is totally board specific; this is indicated by MFP_LPM_EDGE_* c) the corresponding device's (most likely the gpio_keys.c) wakeup attribute: Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-11 08:46:28 +07:00
pr_warning("%s: output GPIO%d unable to wakeup\n",
__func__, gpio);
return -EINVAL;
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 16:16:29 +07:00
}
return 0;
}
[ARM] pxa: introduce dedicated __mfp_validate() to check PXA2xx MFP Signed-off-by: Eric Miao <eric.miao@marvell.com> Tested-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-06-16 08:38:27 +07:00
static inline int __mfp_validate(int mfp)
{
int gpio = mfp_to_gpio(mfp);
if ((mfp > MFP_PIN_GPIO127) || !gpio_desc[gpio].valid) {
pr_warning("%s: GPIO%d is invalid pin\n", __func__, gpio);
return -1;
}
return gpio;
}
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 16:16:29 +07:00
void pxa2xx_mfp_config(unsigned long *mfp_cfgs, int num)
{
unsigned long flags;
unsigned long *c;
int i, gpio;
for (i = 0, c = mfp_cfgs; i < num; i++, c++) {
[ARM] pxa: introduce dedicated __mfp_validate() to check PXA2xx MFP Signed-off-by: Eric Miao <eric.miao@marvell.com> Tested-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-06-16 08:38:27 +07:00
gpio = __mfp_validate(MFP_PIN(*c));
if (gpio < 0)
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 16:16:29 +07:00
continue;
local_irq_save(flags);
gpio_desc[gpio].config = *c;
__mfp_config_gpio(gpio, *c);
local_irq_restore(flags);
}
}
[ARM] pxa: add pxa2xx_mfp_set_lpm() to facilitate low power state change Some boards want to change low power state of pins on-the-fly, this function helps to facilitate that operation instead of switching back-n-forth between two configurations with pxa2xx_mfp_config(). Signed-off-by: Eric Miao <eric.miao@marvell.com> Tested-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-06-16 08:47:47 +07:00
void pxa2xx_mfp_set_lpm(int mfp, unsigned long lpm)
{
[ARM] pxa: better MFP low power state support for pxa25x/pxa27x When configured as a specific low power state: MFP_LPM_DRIVE_LOW, MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during low power mode shall be re-configured as output (if they are not configured so), thus the PGSRx bits can output. Create an additional low power values GPDR registers, and properly save/restore the GAFR + GPDR registers when doing suspend/resume. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-03 17:06:34 +07:00
unsigned long flags, c;
[ARM] pxa: add pxa2xx_mfp_set_lpm() to facilitate low power state change Some boards want to change low power state of pins on-the-fly, this function helps to facilitate that operation instead of switching back-n-forth between two configurations with pxa2xx_mfp_config(). Signed-off-by: Eric Miao <eric.miao@marvell.com> Tested-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-06-16 08:47:47 +07:00
int gpio;
gpio = __mfp_validate(mfp);
if (gpio < 0)
return;
local_irq_save(flags);
[ARM] pxa: better MFP low power state support for pxa25x/pxa27x When configured as a specific low power state: MFP_LPM_DRIVE_LOW, MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during low power mode shall be re-configured as output (if they are not configured so), thus the PGSRx bits can output. Create an additional low power values GPDR registers, and properly save/restore the GAFR + GPDR registers when doing suspend/resume. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-03 17:06:34 +07:00
c = gpio_desc[gpio].config;
c = (c & ~MFP_LPM_STATE_MASK) | lpm;
__mfp_config_gpio(gpio, c);
[ARM] pxa: add pxa2xx_mfp_set_lpm() to facilitate low power state change Some boards want to change low power state of pins on-the-fly, this function helps to facilitate that operation instead of switching back-n-forth between two configurations with pxa2xx_mfp_config(). Signed-off-by: Eric Miao <eric.miao@marvell.com> Tested-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-06-16 08:47:47 +07:00
local_irq_restore(flags);
}
[ARM] pxa: allow dynamic enable/disable of GPIO wakeup for pxa{25x,27x} Changes include: 1. rename MFP_LPM_WAKEUP_ENABLE into MFP_LPM_CAN_WAKEUP to indicate the board capability of this pin to wakeup the system 2. add gpio_set_wake() and keypad_set_wake() to allow dynamically enable/disable wakeup from GPIOs and keypad GPIO * these functions are currently kept in mfp-pxa2xx.c due to their dependency to the MFP configuration 3. pxa2xx_mfp_config() only gives early warning if MFP_LPM_CAN_WAKEUP is set on incorrect pins So that the GPIO's wakeup capability is now decided by the following: a) processor's capability: (only those GPIOs which have dedicated bits within PWER/PRER/PFER can wakeup the system), this is initialized by pxa{25x,27x}_init_mfp() b) board design decides: - whether the pin is designed to wakeup the system (some of the GPIOs are configured as other functions, which is not intended to be a wakeup source), by OR'ing the pin config with MFP_LPM_CAN_WAKEUP - which edge the pin is designed to wakeup the system, this may depends on external peripherals/connections, which is totally board specific; this is indicated by MFP_LPM_EDGE_* c) the corresponding device's (most likely the gpio_keys.c) wakeup attribute: Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-11 08:46:28 +07:00
int gpio_set_wake(unsigned int gpio, unsigned int on)
{
struct gpio_desc *d;
[ARM] pxa: add muxed gpio wakeup sources on pxa2xx architectures PXA SoC have several GPIOs muxed on only one wakeup source. Add support for these wakeup sources which were missing in mfp core support. Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-11-14 05:30:00 +07:00
unsigned long c, mux_taken;
[ARM] pxa: allow dynamic enable/disable of GPIO wakeup for pxa{25x,27x} Changes include: 1. rename MFP_LPM_WAKEUP_ENABLE into MFP_LPM_CAN_WAKEUP to indicate the board capability of this pin to wakeup the system 2. add gpio_set_wake() and keypad_set_wake() to allow dynamically enable/disable wakeup from GPIOs and keypad GPIO * these functions are currently kept in mfp-pxa2xx.c due to their dependency to the MFP configuration 3. pxa2xx_mfp_config() only gives early warning if MFP_LPM_CAN_WAKEUP is set on incorrect pins So that the GPIO's wakeup capability is now decided by the following: a) processor's capability: (only those GPIOs which have dedicated bits within PWER/PRER/PFER can wakeup the system), this is initialized by pxa{25x,27x}_init_mfp() b) board design decides: - whether the pin is designed to wakeup the system (some of the GPIOs are configured as other functions, which is not intended to be a wakeup source), by OR'ing the pin config with MFP_LPM_CAN_WAKEUP - which edge the pin is designed to wakeup the system, this may depends on external peripherals/connections, which is totally board specific; this is indicated by MFP_LPM_EDGE_* c) the corresponding device's (most likely the gpio_keys.c) wakeup attribute: Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-11 08:46:28 +07:00
if (gpio > mfp_to_gpio(MFP_PIN_GPIO127))
return -EINVAL;
d = &gpio_desc[gpio];
c = d->config;
if (!d->valid)
return -EINVAL;
if (d->keypad_gpio)
return -EINVAL;
[ARM] pxa: add muxed gpio wakeup sources on pxa2xx architectures PXA SoC have several GPIOs muxed on only one wakeup source. Add support for these wakeup sources which were missing in mfp core support. Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-11-14 05:30:00 +07:00
mux_taken = (PWER & d->mux_mask) & (~d->mask);
if (on && mux_taken)
return -EBUSY;
[ARM] pxa: allow dynamic enable/disable of GPIO wakeup for pxa{25x,27x} Changes include: 1. rename MFP_LPM_WAKEUP_ENABLE into MFP_LPM_CAN_WAKEUP to indicate the board capability of this pin to wakeup the system 2. add gpio_set_wake() and keypad_set_wake() to allow dynamically enable/disable wakeup from GPIOs and keypad GPIO * these functions are currently kept in mfp-pxa2xx.c due to their dependency to the MFP configuration 3. pxa2xx_mfp_config() only gives early warning if MFP_LPM_CAN_WAKEUP is set on incorrect pins So that the GPIO's wakeup capability is now decided by the following: a) processor's capability: (only those GPIOs which have dedicated bits within PWER/PRER/PFER can wakeup the system), this is initialized by pxa{25x,27x}_init_mfp() b) board design decides: - whether the pin is designed to wakeup the system (some of the GPIOs are configured as other functions, which is not intended to be a wakeup source), by OR'ing the pin config with MFP_LPM_CAN_WAKEUP - which edge the pin is designed to wakeup the system, this may depends on external peripherals/connections, which is totally board specific; this is indicated by MFP_LPM_EDGE_* c) the corresponding device's (most likely the gpio_keys.c) wakeup attribute: Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-11 08:46:28 +07:00
if (d->can_wakeup && (c & MFP_LPM_CAN_WAKEUP)) {
if (on) {
[ARM] pxa: add muxed gpio wakeup sources on pxa2xx architectures PXA SoC have several GPIOs muxed on only one wakeup source. Add support for these wakeup sources which were missing in mfp core support. Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-11-14 05:30:00 +07:00
PWER = (PWER & ~d->mux_mask) | d->mask;
[ARM] pxa: allow dynamic enable/disable of GPIO wakeup for pxa{25x,27x} Changes include: 1. rename MFP_LPM_WAKEUP_ENABLE into MFP_LPM_CAN_WAKEUP to indicate the board capability of this pin to wakeup the system 2. add gpio_set_wake() and keypad_set_wake() to allow dynamically enable/disable wakeup from GPIOs and keypad GPIO * these functions are currently kept in mfp-pxa2xx.c due to their dependency to the MFP configuration 3. pxa2xx_mfp_config() only gives early warning if MFP_LPM_CAN_WAKEUP is set on incorrect pins So that the GPIO's wakeup capability is now decided by the following: a) processor's capability: (only those GPIOs which have dedicated bits within PWER/PRER/PFER can wakeup the system), this is initialized by pxa{25x,27x}_init_mfp() b) board design decides: - whether the pin is designed to wakeup the system (some of the GPIOs are configured as other functions, which is not intended to be a wakeup source), by OR'ing the pin config with MFP_LPM_CAN_WAKEUP - which edge the pin is designed to wakeup the system, this may depends on external peripherals/connections, which is totally board specific; this is indicated by MFP_LPM_EDGE_* c) the corresponding device's (most likely the gpio_keys.c) wakeup attribute: Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-11 08:46:28 +07:00
if (c & MFP_LPM_EDGE_RISE)
PRER |= d->mask;
else
PRER &= ~d->mask;
if (c & MFP_LPM_EDGE_FALL)
PFER |= d->mask;
else
PFER &= ~d->mask;
} else {
PWER &= ~d->mask;
PRER &= ~d->mask;
PFER &= ~d->mask;
}
}
return 0;
}
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 16:16:29 +07:00
#ifdef CONFIG_PXA25x
[ARM] pxa: better MFP low power state support for pxa25x/pxa27x When configured as a specific low power state: MFP_LPM_DRIVE_LOW, MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during low power mode shall be re-configured as output (if they are not configured so), thus the PGSRx bits can output. Create an additional low power values GPDR registers, and properly save/restore the GAFR + GPDR registers when doing suspend/resume. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-03 17:06:34 +07:00
static void __init pxa25x_mfp_init(void)
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 16:16:29 +07:00
{
int i;
[ARM] pxa: use 'pxa_last_gpio' instead of 'gpio_nr' in mfp-pxa2xx.c The 'gpio_nr' can really be inferred by 'pxa_last_gpio', and since we already have that variable, remove the unnecessary 'gpio_nr' now. Also, fix the incorrect GPIO number passed in pxa27x_init_irq(). Note: pxa_last_gpio should be initialized earlier, and this is true since it's been assigned in machine_desc->init_irq(). Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-11-26 16:06:42 +07:00
for (i = 0; i <= pxa_last_gpio; i++)
[ARM] pxa: better MFP low power state support for pxa25x/pxa27x When configured as a specific low power state: MFP_LPM_DRIVE_LOW, MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during low power mode shall be re-configured as output (if they are not configured so), thus the PGSRx bits can output. Create an additional low power values GPDR registers, and properly save/restore the GAFR + GPDR registers when doing suspend/resume. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-03 17:06:34 +07:00
gpio_desc[i].valid = 1;
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 16:16:29 +07:00
[ARM] pxa: better MFP low power state support for pxa25x/pxa27x When configured as a specific low power state: MFP_LPM_DRIVE_LOW, MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during low power mode shall be re-configured as output (if they are not configured so), thus the PGSRx bits can output. Create an additional low power values GPDR registers, and properly save/restore the GAFR + GPDR registers when doing suspend/resume. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-03 17:06:34 +07:00
for (i = 0; i <= 15; i++) {
gpio_desc[i].can_wakeup = 1;
gpio_desc[i].mask = GPIO_bit(i);
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 16:16:29 +07:00
}
[ARM] pxa: add support for additional GPIOs on PXA26x Original patch from Marek Vasut, the problems with PXA26x are: 1. there are additional 4 GPIOs 86,87,88,89 have their direction bits inverted in GPDR2, as well as their alternate function bits being '1' for their GPIO functionality in GAFRx 2. there is no easy way to decide if the processor is a pxa26x or a pxa250/pxa255 at run-time, so the assumption here is the pxa26x will be treated as one of the pxa25x variants, and board code should have a better knowledge of the processor it is featured Introduce pxa26x_init_irq() for the second purpose, and treat the additional GPIOs > 85 on PXA25x specially. Kconfig option CONFIG_CPU_PXA26x is introduced to optimize the code a bit when PXA26x support isn't needed. Board config options have to select this to enable the support for PXA26x. __gpio_is_inverted() will be optimized way when CONFIG_CPU_PXA26x isn't selected. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-11-26 17:12:04 +07:00
/* PXA26x has additional 4 GPIOs (86/87/88/89) which has the
* direction bit inverted in GPDR2. See PXA26x DM 4.1.1.
*/
for (i = 86; i <= pxa_last_gpio; i++)
gpio_desc[i].dir_inverted = 1;
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 16:16:29 +07:00
}
[ARM] pxa: better MFP low power state support for pxa25x/pxa27x When configured as a specific low power state: MFP_LPM_DRIVE_LOW, MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during low power mode shall be re-configured as output (if they are not configured so), thus the PGSRx bits can output. Create an additional low power values GPDR registers, and properly save/restore the GAFR + GPDR registers when doing suspend/resume. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-03 17:06:34 +07:00
#else
static inline void pxa25x_mfp_init(void) {}
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 16:16:29 +07:00
#endif /* CONFIG_PXA25x */
#ifdef CONFIG_PXA27x
[ARM] pxa: allow dynamic enable/disable of GPIO wakeup for pxa{25x,27x} Changes include: 1. rename MFP_LPM_WAKEUP_ENABLE into MFP_LPM_CAN_WAKEUP to indicate the board capability of this pin to wakeup the system 2. add gpio_set_wake() and keypad_set_wake() to allow dynamically enable/disable wakeup from GPIOs and keypad GPIO * these functions are currently kept in mfp-pxa2xx.c due to their dependency to the MFP configuration 3. pxa2xx_mfp_config() only gives early warning if MFP_LPM_CAN_WAKEUP is set on incorrect pins So that the GPIO's wakeup capability is now decided by the following: a) processor's capability: (only those GPIOs which have dedicated bits within PWER/PRER/PFER can wakeup the system), this is initialized by pxa{25x,27x}_init_mfp() b) board design decides: - whether the pin is designed to wakeup the system (some of the GPIOs are configured as other functions, which is not intended to be a wakeup source), by OR'ing the pin config with MFP_LPM_CAN_WAKEUP - which edge the pin is designed to wakeup the system, this may depends on external peripherals/connections, which is totally board specific; this is indicated by MFP_LPM_EDGE_* c) the corresponding device's (most likely the gpio_keys.c) wakeup attribute: Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-11 08:46:28 +07:00
static int pxa27x_pkwr_gpio[] = {
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 16:16:29 +07:00
13, 16, 17, 34, 36, 37, 38, 39, 90, 91, 93, 94,
95, 96, 97, 98, 99, 100, 101, 102
};
[ARM] pxa: allow dynamic enable/disable of GPIO wakeup for pxa{25x,27x} Changes include: 1. rename MFP_LPM_WAKEUP_ENABLE into MFP_LPM_CAN_WAKEUP to indicate the board capability of this pin to wakeup the system 2. add gpio_set_wake() and keypad_set_wake() to allow dynamically enable/disable wakeup from GPIOs and keypad GPIO * these functions are currently kept in mfp-pxa2xx.c due to their dependency to the MFP configuration 3. pxa2xx_mfp_config() only gives early warning if MFP_LPM_CAN_WAKEUP is set on incorrect pins So that the GPIO's wakeup capability is now decided by the following: a) processor's capability: (only those GPIOs which have dedicated bits within PWER/PRER/PFER can wakeup the system), this is initialized by pxa{25x,27x}_init_mfp() b) board design decides: - whether the pin is designed to wakeup the system (some of the GPIOs are configured as other functions, which is not intended to be a wakeup source), by OR'ing the pin config with MFP_LPM_CAN_WAKEUP - which edge the pin is designed to wakeup the system, this may depends on external peripherals/connections, which is totally board specific; this is indicated by MFP_LPM_EDGE_* c) the corresponding device's (most likely the gpio_keys.c) wakeup attribute: Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-11 08:46:28 +07:00
int keypad_set_wake(unsigned int on)
{
unsigned int i, gpio, mask = 0;
if (!on) {
PKWR = 0;
return 0;
}
for (i = 0; i < ARRAY_SIZE(pxa27x_pkwr_gpio); i++) {
gpio = pxa27x_pkwr_gpio[i];
if (gpio_desc[gpio].config & MFP_LPM_CAN_WAKEUP)
mask |= gpio_desc[gpio].mask;
}
PKWR = mask;
return 0;
}
[ARM] pxa: add muxed gpio wakeup sources on pxa2xx architectures PXA SoC have several GPIOs muxed on only one wakeup source. Add support for these wakeup sources which were missing in mfp core support. Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-11-14 05:30:00 +07:00
#define PWER_WEMUX2_GPIO38 (1 << 16)
#define PWER_WEMUX2_GPIO53 (2 << 16)
#define PWER_WEMUX2_GPIO40 (3 << 16)
#define PWER_WEMUX2_GPIO36 (4 << 16)
#define PWER_WEMUX2_MASK (7 << 16)
#define PWER_WEMUX3_GPIO31 (1 << 19)
#define PWER_WEMUX3_GPIO113 (2 << 19)
#define PWER_WEMUX3_MASK (3 << 19)
#define INIT_GPIO_DESC_MUXED(mux, gpio) \
do { \
gpio_desc[(gpio)].can_wakeup = 1; \
gpio_desc[(gpio)].mask = PWER_ ## mux ## _GPIO ##gpio; \
gpio_desc[(gpio)].mux_mask = PWER_ ## mux ## _MASK; \
} while (0)
[ARM] pxa: better MFP low power state support for pxa25x/pxa27x When configured as a specific low power state: MFP_LPM_DRIVE_LOW, MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during low power mode shall be re-configured as output (if they are not configured so), thus the PGSRx bits can output. Create an additional low power values GPDR registers, and properly save/restore the GAFR + GPDR registers when doing suspend/resume. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-03 17:06:34 +07:00
static void __init pxa27x_mfp_init(void)
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 16:16:29 +07:00
{
int i, gpio;
[ARM] pxa: use 'pxa_last_gpio' instead of 'gpio_nr' in mfp-pxa2xx.c The 'gpio_nr' can really be inferred by 'pxa_last_gpio', and since we already have that variable, remove the unnecessary 'gpio_nr' now. Also, fix the incorrect GPIO number passed in pxa27x_init_irq(). Note: pxa_last_gpio should be initialized earlier, and this is true since it's been assigned in machine_desc->init_irq(). Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-11-26 16:06:42 +07:00
for (i = 0; i <= pxa_last_gpio; i++) {
[ARM] pxa: better MFP low power state support for pxa25x/pxa27x When configured as a specific low power state: MFP_LPM_DRIVE_LOW, MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during low power mode shall be re-configured as output (if they are not configured so), thus the PGSRx bits can output. Create an additional low power values GPDR registers, and properly save/restore the GAFR + GPDR registers when doing suspend/resume. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-03 17:06:34 +07:00
/* skip GPIO2, 5, 6, 7, 8, they are not
* valid pins allow configuration
*/
if (i == 2 || i == 5 || i == 6 || i == 7 || i == 8)
continue;
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 16:16:29 +07:00
[ARM] pxa: better MFP low power state support for pxa25x/pxa27x When configured as a specific low power state: MFP_LPM_DRIVE_LOW, MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during low power mode shall be re-configured as output (if they are not configured so), thus the PGSRx bits can output. Create an additional low power values GPDR registers, and properly save/restore the GAFR + GPDR registers when doing suspend/resume. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-03 17:06:34 +07:00
gpio_desc[i].valid = 1;
}
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 16:16:29 +07:00
[ARM] pxa: better MFP low power state support for pxa25x/pxa27x When configured as a specific low power state: MFP_LPM_DRIVE_LOW, MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during low power mode shall be re-configured as output (if they are not configured so), thus the PGSRx bits can output. Create an additional low power values GPDR registers, and properly save/restore the GAFR + GPDR registers when doing suspend/resume. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-03 17:06:34 +07:00
/* Keypad GPIOs */
for (i = 0; i < ARRAY_SIZE(pxa27x_pkwr_gpio); i++) {
gpio = pxa27x_pkwr_gpio[i];
gpio_desc[gpio].can_wakeup = 1;
gpio_desc[gpio].keypad_gpio = 1;
gpio_desc[gpio].mask = 1 << i;
}
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 16:16:29 +07:00
[ARM] pxa: better MFP low power state support for pxa25x/pxa27x When configured as a specific low power state: MFP_LPM_DRIVE_LOW, MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during low power mode shall be re-configured as output (if they are not configured so), thus the PGSRx bits can output. Create an additional low power values GPDR registers, and properly save/restore the GAFR + GPDR registers when doing suspend/resume. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-03 17:06:34 +07:00
/* Overwrite GPIO13 as a PWER wakeup source */
for (i = 0; i <= 15; i++) {
/* skip GPIO2, 5, 6, 7, 8 */
if (GPIO_bit(i) & 0x1e4)
continue;
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 16:16:29 +07:00
[ARM] pxa: better MFP low power state support for pxa25x/pxa27x When configured as a specific low power state: MFP_LPM_DRIVE_LOW, MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during low power mode shall be re-configured as output (if they are not configured so), thus the PGSRx bits can output. Create an additional low power values GPDR registers, and properly save/restore the GAFR + GPDR registers when doing suspend/resume. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-03 17:06:34 +07:00
gpio_desc[i].can_wakeup = 1;
gpio_desc[i].mask = GPIO_bit(i);
}
gpio_desc[35].can_wakeup = 1;
gpio_desc[35].mask = PWER_WE35;
[ARM] pxa: add muxed gpio wakeup sources on pxa2xx architectures PXA SoC have several GPIOs muxed on only one wakeup source. Add support for these wakeup sources which were missing in mfp core support. Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-11-14 05:30:00 +07:00
INIT_GPIO_DESC_MUXED(WEMUX3, 31);
INIT_GPIO_DESC_MUXED(WEMUX3, 113);
INIT_GPIO_DESC_MUXED(WEMUX2, 38);
INIT_GPIO_DESC_MUXED(WEMUX2, 53);
INIT_GPIO_DESC_MUXED(WEMUX2, 40);
INIT_GPIO_DESC_MUXED(WEMUX2, 36);
[ARM] pxa: better MFP low power state support for pxa25x/pxa27x When configured as a specific low power state: MFP_LPM_DRIVE_LOW, MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during low power mode shall be re-configured as output (if they are not configured so), thus the PGSRx bits can output. Create an additional low power values GPDR registers, and properly save/restore the GAFR + GPDR registers when doing suspend/resume. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-03 17:06:34 +07:00
}
#else
static inline void pxa27x_mfp_init(void) {}
#endif /* CONFIG_PXA27x */
#ifdef CONFIG_PM
static unsigned long saved_gafr[2][4];
static unsigned long saved_gpdr[4];
[ARM] pxa: save/restore PGSR on suspend/resume. Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com> Signed-off-by: Eric Miao <eric.miao@marvell.com>
2009-05-03 01:05:59 +07:00
static unsigned long saved_pgsr[4];
[ARM] pxa: better MFP low power state support for pxa25x/pxa27x When configured as a specific low power state: MFP_LPM_DRIVE_LOW, MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during low power mode shall be re-configured as output (if they are not configured so), thus the PGSRx bits can output. Create an additional low power values GPDR registers, and properly save/restore the GAFR + GPDR registers when doing suspend/resume. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-03 17:06:34 +07:00
static int pxa2xx_mfp_suspend(struct sys_device *d, pm_message_t state)
{
int i;
[ARM] pxa: use 'pxa_last_gpio' instead of 'gpio_nr' in mfp-pxa2xx.c The 'gpio_nr' can really be inferred by 'pxa_last_gpio', and since we already have that variable, remove the unnecessary 'gpio_nr' now. Also, fix the incorrect GPIO number passed in pxa27x_init_irq(). Note: pxa_last_gpio should be initialized earlier, and this is true since it's been assigned in machine_desc->init_irq(). Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-11-26 16:06:42 +07:00
for (i = 0; i <= gpio_to_bank(pxa_last_gpio); i++) {
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 16:16:29 +07:00
[ARM] pxa: better MFP low power state support for pxa25x/pxa27x When configured as a specific low power state: MFP_LPM_DRIVE_LOW, MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during low power mode shall be re-configured as output (if they are not configured so), thus the PGSRx bits can output. Create an additional low power values GPDR registers, and properly save/restore the GAFR + GPDR registers when doing suspend/resume. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-03 17:06:34 +07:00
saved_gafr[0][i] = GAFR_L(i);
saved_gafr[1][i] = GAFR_U(i);
saved_gpdr[i] = GPDR(i * 32);
[ARM] pxa: save/restore PGSR on suspend/resume. Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com> Signed-off-by: Eric Miao <eric.miao@marvell.com>
2009-05-03 01:05:59 +07:00
saved_pgsr[i] = PGSR(i);
[ARM] pxa: better MFP low power state support for pxa25x/pxa27x When configured as a specific low power state: MFP_LPM_DRIVE_LOW, MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during low power mode shall be re-configured as output (if they are not configured so), thus the PGSRx bits can output. Create an additional low power values GPDR registers, and properly save/restore the GAFR + GPDR registers when doing suspend/resume. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-03 17:06:34 +07:00
GPDR(i * 32) = gpdr_lpm[i];
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 16:16:29 +07:00
}
[ARM] pxa: better MFP low power state support for pxa25x/pxa27x When configured as a specific low power state: MFP_LPM_DRIVE_LOW, MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during low power mode shall be re-configured as output (if they are not configured so), thus the PGSRx bits can output. Create an additional low power values GPDR registers, and properly save/restore the GAFR + GPDR registers when doing suspend/resume. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-03 17:06:34 +07:00
return 0;
}
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 16:16:29 +07:00
[ARM] pxa: better MFP low power state support for pxa25x/pxa27x When configured as a specific low power state: MFP_LPM_DRIVE_LOW, MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during low power mode shall be re-configured as output (if they are not configured so), thus the PGSRx bits can output. Create an additional low power values GPDR registers, and properly save/restore the GAFR + GPDR registers when doing suspend/resume. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-03 17:06:34 +07:00
static int pxa2xx_mfp_resume(struct sys_device *d)
{
int i;
[ARM] pxa: use 'pxa_last_gpio' instead of 'gpio_nr' in mfp-pxa2xx.c The 'gpio_nr' can really be inferred by 'pxa_last_gpio', and since we already have that variable, remove the unnecessary 'gpio_nr' now. Also, fix the incorrect GPIO number passed in pxa27x_init_irq(). Note: pxa_last_gpio should be initialized earlier, and this is true since it's been assigned in machine_desc->init_irq(). Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-11-26 16:06:42 +07:00
for (i = 0; i <= gpio_to_bank(pxa_last_gpio); i++) {
[ARM] pxa: better MFP low power state support for pxa25x/pxa27x When configured as a specific low power state: MFP_LPM_DRIVE_LOW, MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during low power mode shall be re-configured as output (if they are not configured so), thus the PGSRx bits can output. Create an additional low power values GPDR registers, and properly save/restore the GAFR + GPDR registers when doing suspend/resume. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-03 17:06:34 +07:00
GAFR_L(i) = saved_gafr[0][i];
GAFR_U(i) = saved_gafr[1][i];
GPDR(i * 32) = saved_gpdr[i];
[ARM] pxa: save/restore PGSR on suspend/resume. Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com> Signed-off-by: Eric Miao <eric.miao@marvell.com>
2009-05-03 01:05:59 +07:00
PGSR(i) = saved_pgsr[i];
[ARM] pxa: better MFP low power state support for pxa25x/pxa27x When configured as a specific low power state: MFP_LPM_DRIVE_LOW, MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during low power mode shall be re-configured as output (if they are not configured so), thus the PGSRx bits can output. Create an additional low power values GPDR registers, and properly save/restore the GAFR + GPDR registers when doing suspend/resume. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-03 17:06:34 +07:00
}
PSSR = PSSR_RDH | PSSR_PH;
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x} Pin configuration on pxa{25x,27x} has now separated from generic GPIO into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed from pxa3xx and is used here to alert the difference between the two concepts: pin configuration and generic GPIOs. A GPIO can be called a "GPIO" _only_ when the corresponding pin is configured so. A pin configuration on pxa{25x,27x} is composed of: - alternate function selection (or pin mux as commonly called) - low power state or sleep state - wakeup enabling from low power mode The following MFP_xxx bit definitions in mfp.h are re-used: - MFP_PIN(x) - MFP_AFx - MFP_LPM_DRIVE_{LOW, HIGH} - MFP_LPM_EDGE_* Selecting alternate function on pxa{25x, 27x} involves configuration of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT} are introduced. And pin configurations are defined by the following two macros: - MFP_CFG_IN : for input alternate functions - MFP_CFG_OUT : for output alternate functions Every configuration should provide a low power state if it configured as output using MFP_CFG_OUT(). As a general guideline, the low power state should be decided to minimize the overall power dissipation. As an example, it is better to drive the pin as high level in low power mode if the GPIO is configured as an active low chip select. Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid side effects when it is firstly configured as output. The actual direction of the GPIO is configured by gpio_direction_{input, output} Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus the device based enable_irq_wake() mechanism is not applicable here. E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following code to enable OTG wakeup is by no means portable and intuitive, and it is valid _only_ when GPIO35 is configured as USB_P2_1: enable_irq_wake( gpio_to_irq(35) ); To make things worse, not every GPIO is able to wakeup the system. Only a small number of them can, on either rising or falling edge, or when level is high (for keypad GPIOs). Thus, another new bit is introduced to indicate that the GPIO will wakeup the system: - MFP_LPM_WAKEUP_ENABLE The following macros can be used in platform code, and be OR'ed to the GPIO configuration to enable its wakeup: - WAKEUP_ON_EDGE_{RISE, FALL, BOTH} - WAKEUP_ON_LEVEL_HIGH The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is no edge settings for those GPIOs. These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case that platform code author is careless enough. The tradeoff here is that the wakeup source is fully determined by the platform configuration, instead of enable_irq_wake(). Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-03-05 16:16:29 +07:00
return 0;
}
[ARM] pxa: better MFP low power state support for pxa25x/pxa27x When configured as a specific low power state: MFP_LPM_DRIVE_LOW, MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during low power mode shall be re-configured as output (if they are not configured so), thus the PGSRx bits can output. Create an additional low power values GPDR registers, and properly save/restore the GAFR + GPDR registers when doing suspend/resume. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-03 17:06:34 +07:00
#else
#define pxa2xx_mfp_suspend NULL
#define pxa2xx_mfp_resume NULL
#endif
struct sysdev_class pxa2xx_mfp_sysclass = {
.name = "mfp",
.suspend = pxa2xx_mfp_suspend,
.resume = pxa2xx_mfp_resume,
};
static int __init pxa2xx_mfp_init(void)
{
int i;
[ARM] pxa: fix incorrect initialization of mfp sysdev when not pxa2xx The initialization of mfp sysdev in pxa2xx_mfp_init() shall really be avoided when !cpu_is_pxa2xx(). Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-27 17:07:48 +07:00
if (!cpu_is_pxa2xx())
return 0;
[ARM] pxa: better MFP low power state support for pxa25x/pxa27x When configured as a specific low power state: MFP_LPM_DRIVE_LOW, MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during low power mode shall be re-configured as output (if they are not configured so), thus the PGSRx bits can output. Create an additional low power values GPDR registers, and properly save/restore the GAFR + GPDR registers when doing suspend/resume. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-03 17:06:34 +07:00
if (cpu_is_pxa25x())
pxa25x_mfp_init();
if (cpu_is_pxa27x())
pxa27x_mfp_init();
[ARM] pxa: enable GPIO receivers after configuring pins 'mach-pxa' platforms currently rely on a bootloader to setup GPIO pins and clear RDH (to enable inputs). A kernel loaded by a 'minimal' bootloader, that doesn't touch any pins, will not function correctly; inputs will remain disabled, even after the pins are configured. The following change fixes the issue and has been verified on Gumstix Verdex XL6P and a custom PXA270 platform. Signed-off-by: Timothy Clacy <tcl@phaseone.com> Signed-off-by: Eric Miao <eric.miao@marvell.com>
2009-05-08 00:40:33 +07:00
/* clear RDH bit to enable GPIO receivers after reset/sleep exit */
PSSR = PSSR_RDH;
[ARM] pxa: better MFP low power state support for pxa25x/pxa27x When configured as a specific low power state: MFP_LPM_DRIVE_LOW, MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during low power mode shall be re-configured as output (if they are not configured so), thus the PGSRx bits can output. Create an additional low power values GPDR registers, and properly save/restore the GAFR + GPDR registers when doing suspend/resume. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-03 17:06:34 +07:00
/* initialize gafr_run[], pgsr_lpm[] from existing values */
[ARM] pxa: use 'pxa_last_gpio' instead of 'gpio_nr' in mfp-pxa2xx.c The 'gpio_nr' can really be inferred by 'pxa_last_gpio', and since we already have that variable, remove the unnecessary 'gpio_nr' now. Also, fix the incorrect GPIO number passed in pxa27x_init_irq(). Note: pxa_last_gpio should be initialized earlier, and this is true since it's been assigned in machine_desc->init_irq(). Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-11-26 16:06:42 +07:00
for (i = 0; i <= gpio_to_bank(pxa_last_gpio); i++)
[ARM] pxa: better MFP low power state support for pxa25x/pxa27x When configured as a specific low power state: MFP_LPM_DRIVE_LOW, MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during low power mode shall be re-configured as output (if they are not configured so), thus the PGSRx bits can output. Create an additional low power values GPDR registers, and properly save/restore the GAFR + GPDR registers when doing suspend/resume. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-03 17:06:34 +07:00
gpdr_lpm[i] = GPDR(i * 32);
return sysdev_class_register(&pxa2xx_mfp_sysclass);
}
postcore_initcall(pxa2xx_mfp_init);
Reference in New Issue Copy Permalink