linux_dsm_epyc7002/drivers/net/phy/mscc.c

3825 lines
106 KiB
C
Raw Normal View History

// SPDX-License-Identifier: (GPL-2.0 OR MIT)
/*
* Driver for Microsemi VSC85xx PHYs
*
* Author: Nagaraju Lakkaraju
* License: Dual MIT/GPL
* Copyright (c) 2016 Microsemi Corporation
*/
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
#include <linux/firmware.h>
#include <linux/jiffies.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/mdio.h>
#include <linux/mii.h>
#include <linux/phy.h>
#include <linux/of.h>
#include <linux/netdevice.h>
#include <dt-bindings/net/mscc-phy-vsc8531.h>
#include <linux/scatterlist.h>
#include <crypto/skcipher.h>
#if IS_ENABLED(CONFIG_MACSEC)
#include <net/macsec.h>
#endif
#include "mscc_macsec.h"
#include "mscc_mac.h"
#include "mscc_fc_buffer.h"
enum rgmii_rx_clock_delay {
RGMII_RX_CLK_DELAY_0_2_NS = 0,
RGMII_RX_CLK_DELAY_0_8_NS = 1,
RGMII_RX_CLK_DELAY_1_1_NS = 2,
RGMII_RX_CLK_DELAY_1_7_NS = 3,
RGMII_RX_CLK_DELAY_2_0_NS = 4,
RGMII_RX_CLK_DELAY_2_3_NS = 5,
RGMII_RX_CLK_DELAY_2_6_NS = 6,
RGMII_RX_CLK_DELAY_3_4_NS = 7
};
/* Microsemi VSC85xx PHY registers */
/* IEEE 802. Std Registers */
#define MSCC_PHY_BYPASS_CONTROL 18
#define DISABLE_HP_AUTO_MDIX_MASK 0x0080
#define DISABLE_PAIR_SWAP_CORR_MASK 0x0020
#define DISABLE_POLARITY_CORR_MASK 0x0010
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
#define PARALLEL_DET_IGNORE_ADVERTISED 0x0008
#define MSCC_PHY_EXT_CNTL_STATUS 22
#define SMI_BROADCAST_WR_EN 0x0001
#define MSCC_PHY_ERR_RX_CNT 19
#define MSCC_PHY_ERR_FALSE_CARRIER_CNT 20
#define MSCC_PHY_ERR_LINK_DISCONNECT_CNT 21
#define ERR_CNT_MASK GENMASK(7, 0)
#define MSCC_PHY_EXT_PHY_CNTL_1 23
#define MAC_IF_SELECTION_MASK 0x1800
#define MAC_IF_SELECTION_GMII 0
#define MAC_IF_SELECTION_RMII 1
#define MAC_IF_SELECTION_RGMII 2
#define MAC_IF_SELECTION_POS 11
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
#define VSC8584_MAC_IF_SELECTION_MASK 0x1000
#define VSC8584_MAC_IF_SELECTION_SGMII 0
#define VSC8584_MAC_IF_SELECTION_1000BASEX 1
#define VSC8584_MAC_IF_SELECTION_POS 12
#define FAR_END_LOOPBACK_MODE_MASK 0x0008
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
#define MEDIA_OP_MODE_MASK 0x0700
#define MEDIA_OP_MODE_COPPER 0
#define MEDIA_OP_MODE_SERDES 1
#define MEDIA_OP_MODE_1000BASEX 2
#define MEDIA_OP_MODE_100BASEFX 3
#define MEDIA_OP_MODE_AMS_COPPER_SERDES 5
#define MEDIA_OP_MODE_AMS_COPPER_1000BASEX 6
#define MEDIA_OP_MODE_AMS_COPPER_100BASEFX 7
#define MEDIA_OP_MODE_POS 8
net: phy: mscc: add support for VSC8574 PHY The VSC8574 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports WOL, downshifting and can set the blinking pattern of each of its 4 LEDs, supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, WOL, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8574 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:43 +07:00
#define MSCC_PHY_EXT_PHY_CNTL_2 24
#define MII_VSC85XX_INT_MASK 25
#define MII_VSC85XX_INT_MASK_MASK 0xa020
#define MII_VSC85XX_INT_MASK_WOL 0x0040
#define MII_VSC85XX_INT_STATUS 26
#define MSCC_PHY_WOL_MAC_CONTROL 27
#define EDGE_RATE_CNTL_POS 5
#define EDGE_RATE_CNTL_MASK 0x00E0
#define MSCC_PHY_DEV_AUX_CNTL 28
#define HP_AUTO_MDIX_X_OVER_IND_MASK 0x2000
#define MSCC_PHY_LED_MODE_SEL 29
#define LED_MODE_SEL_POS(x) ((x) * 4)
#define LED_MODE_SEL_MASK(x) (GENMASK(3, 0) << LED_MODE_SEL_POS(x))
#define LED_MODE_SEL(x, mode) (((mode) << LED_MODE_SEL_POS(x)) & LED_MODE_SEL_MASK(x))
net: phy: mscc: add support for VSC8514 PHY. The VSC8514 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X, can communicate with the MAC via QSGMII. The MAC interface protocol for each port within QSGMII can be either 1000BASE-X or SGMII, if the QSGMII MAC that the VSC8514 is connecting to supports this functionality. VSC8514 also supports SGMII MAC-side autonegotiation on each individual port, downshifting, can set the blinking pattern of each of its 4 LEDs, SyncE, 1000BASE-T Ring Resiliency as well as HP Auto-MDIX detection. This adds support for 10BASE-T, 100BASE-TX, and 1000BASE-T, QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. Signed-off-by: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com> Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Co-developed-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-22 18:51:35 +07:00
#define MSCC_EXT_PAGE_CSR_CNTL_17 17
#define MSCC_EXT_PAGE_CSR_CNTL_18 18
#define MSCC_EXT_PAGE_CSR_CNTL_19 19
#define MSCC_PHY_CSR_CNTL_19_REG_ADDR(x) (x)
#define MSCC_PHY_CSR_CNTL_19_TARGET(x) ((x) << 12)
#define MSCC_PHY_CSR_CNTL_19_READ BIT(14)
#define MSCC_PHY_CSR_CNTL_19_CMD BIT(15)
#define MSCC_EXT_PAGE_CSR_CNTL_20 20
#define MSCC_PHY_CSR_CNTL_20_TARGET(x) (x)
#define PHY_MCB_TARGET 0x07
#define PHY_MCB_S6G_WRITE BIT(31)
#define PHY_MCB_S6G_READ BIT(30)
#define PHY_S6G_PLL5G_CFG0 0x06
#define PHY_S6G_LCPLL_CFG 0x11
#define PHY_S6G_PLL_CFG 0x2b
#define PHY_S6G_COMMON_CFG 0x2c
#define PHY_S6G_GPC_CFG 0x2e
#define PHY_S6G_MISC_CFG 0x3b
#define PHY_MCB_S6G_CFG 0x3f
#define PHY_S6G_DFT_CFG2 0x3e
#define PHY_S6G_PLL_STATUS 0x31
#define PHY_S6G_IB_STATUS0 0x2f
#define PHY_S6G_SYS_RST_POS 31
#define PHY_S6G_ENA_LANE_POS 18
#define PHY_S6G_ENA_LOOP_POS 8
#define PHY_S6G_QRATE_POS 6
#define PHY_S6G_IF_MODE_POS 4
#define PHY_S6G_PLL_ENA_OFFS_POS 21
#define PHY_S6G_PLL_FSM_CTRL_DATA_POS 8
#define PHY_S6G_PLL_FSM_ENA_POS 7
#define MSCC_EXT_PAGE_MACSEC_17 17
#define MSCC_EXT_PAGE_MACSEC_18 18
#define MSCC_EXT_PAGE_MACSEC_19 19
#define MSCC_PHY_MACSEC_19_REG_ADDR(x) (x)
#define MSCC_PHY_MACSEC_19_TARGET(x) ((x) << 12)
#define MSCC_PHY_MACSEC_19_READ BIT(14)
#define MSCC_PHY_MACSEC_19_CMD BIT(15)
#define MSCC_EXT_PAGE_MACSEC_20 20
#define MSCC_PHY_MACSEC_20_TARGET(x) (x)
enum macsec_bank {
FC_BUFFER = 0x04,
HOST_MAC = 0x05,
LINE_MAC = 0x06,
IP_1588 = 0x0e,
MACSEC_INGR = 0x38,
MACSEC_EGR = 0x3c,
};
#define MSCC_EXT_PAGE_ACCESS 31
#define MSCC_PHY_PAGE_STANDARD 0x0000 /* Standard registers */
#define MSCC_PHY_PAGE_EXTENDED 0x0001 /* Extended registers */
#define MSCC_PHY_PAGE_EXTENDED_2 0x0002 /* Extended reg - page 2 */
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
#define MSCC_PHY_PAGE_EXTENDED_3 0x0003 /* Extended reg - page 3 */
#define MSCC_PHY_PAGE_EXTENDED_4 0x0004 /* Extended reg - page 4 */
net: phy: mscc: add support for VSC8514 PHY. The VSC8514 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X, can communicate with the MAC via QSGMII. The MAC interface protocol for each port within QSGMII can be either 1000BASE-X or SGMII, if the QSGMII MAC that the VSC8514 is connecting to supports this functionality. VSC8514 also supports SGMII MAC-side autonegotiation on each individual port, downshifting, can set the blinking pattern of each of its 4 LEDs, SyncE, 1000BASE-T Ring Resiliency as well as HP Auto-MDIX detection. This adds support for 10BASE-T, 100BASE-TX, and 1000BASE-T, QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. Signed-off-by: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com> Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Co-developed-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-22 18:51:35 +07:00
#define MSCC_PHY_PAGE_CSR_CNTL MSCC_PHY_PAGE_EXTENDED_4
#define MSCC_PHY_PAGE_MACSEC MSCC_PHY_PAGE_EXTENDED_4
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
/* Extended reg - GPIO; this is a bank of registers that are shared for all PHYs
* in the same package.
*/
#define MSCC_PHY_PAGE_EXTENDED_GPIO 0x0010 /* Extended reg - GPIO */
#define MSCC_PHY_PAGE_TEST 0x2a30 /* Test reg */
#define MSCC_PHY_PAGE_TR 0x52b5 /* Token ring registers */
/* Extended Page 1 Registers */
#define MSCC_PHY_CU_MEDIA_CRC_VALID_CNT 18
#define VALID_CRC_CNT_CRC_MASK GENMASK(13, 0)
#define MSCC_PHY_EXT_MODE_CNTL 19
#define FORCE_MDI_CROSSOVER_MASK 0x000C
#define FORCE_MDI_CROSSOVER_MDIX 0x000C
#define FORCE_MDI_CROSSOVER_MDI 0x0008
#define MSCC_PHY_ACTIPHY_CNTL 20
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
#define PHY_ADDR_REVERSED 0x0200
#define DOWNSHIFT_CNTL_MASK 0x001C
#define DOWNSHIFT_EN 0x0010
#define DOWNSHIFT_CNTL_POS 2
#define MSCC_PHY_EXT_PHY_CNTL_4 23
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
#define PHY_CNTL_4_ADDR_POS 11
#define MSCC_PHY_VERIPHY_CNTL_2 25
#define MSCC_PHY_VERIPHY_CNTL_3 26
/* Extended Page 2 Registers */
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
#define MSCC_PHY_CU_PMD_TX_CNTL 16
#define MSCC_PHY_RGMII_CNTL 20
#define RGMII_RX_CLK_DELAY_MASK 0x0070
#define RGMII_RX_CLK_DELAY_POS 4
#define MSCC_PHY_WOL_LOWER_MAC_ADDR 21
#define MSCC_PHY_WOL_MID_MAC_ADDR 22
#define MSCC_PHY_WOL_UPPER_MAC_ADDR 23
#define MSCC_PHY_WOL_LOWER_PASSWD 24
#define MSCC_PHY_WOL_MID_PASSWD 25
#define MSCC_PHY_WOL_UPPER_PASSWD 26
#define MSCC_PHY_WOL_MAC_CONTROL 27
#define SECURE_ON_ENABLE 0x8000
#define SECURE_ON_PASSWD_LEN_4 0x4000
#define MSCC_PHY_EXTENDED_INT 28
#define MSCC_PHY_EXTENDED_INT_MS_EGR BIT(9)
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
/* Extended Page 3 Registers */
#define MSCC_PHY_SERDES_TX_VALID_CNT 21
#define MSCC_PHY_SERDES_TX_CRC_ERR_CNT 22
#define MSCC_PHY_SERDES_RX_VALID_CNT 28
#define MSCC_PHY_SERDES_RX_CRC_ERR_CNT 29
/* Extended page GPIO Registers */
#define MSCC_DW8051_CNTL_STATUS 0
#define MICRO_NSOFT_RESET 0x8000
#define RUN_FROM_INT_ROM 0x4000
#define AUTOINC_ADDR 0x2000
#define PATCH_RAM_CLK 0x1000
#define MICRO_PATCH_EN 0x0080
#define DW8051_CLK_EN 0x0010
#define MICRO_CLK_EN 0x0008
#define MICRO_CLK_DIVIDE(x) ((x) >> 1)
net: phy: mscc: add support for VSC8574 PHY The VSC8574 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports WOL, downshifting and can set the blinking pattern of each of its 4 LEDs, supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, WOL, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8574 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:43 +07:00
#define MSCC_DW8051_VLD_MASK 0xf1ff
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
/* x Address in range 1-4 */
#define MSCC_TRAP_ROM_ADDR(x) ((x) * 2 + 1)
#define MSCC_PATCH_RAM_ADDR(x) (((x) + 1) * 2)
#define MSCC_INT_MEM_ADDR 11
#define MSCC_INT_MEM_CNTL 12
#define READ_SFR 0x6000
#define READ_PRAM 0x4000
#define READ_ROM 0x2000
#define READ_RAM 0x0000
#define INT_MEM_WRITE_EN 0x1000
#define EN_PATCH_RAM_TRAP_ADDR(x) (0x0100 << ((x) - 1))
#define INT_MEM_DATA_M 0x00ff
#define INT_MEM_DATA(x) (INT_MEM_DATA_M & (x))
#define MSCC_PHY_PROC_CMD 18
#define PROC_CMD_NCOMPLETED 0x8000
#define PROC_CMD_FAILED 0x4000
#define PROC_CMD_SGMII_PORT(x) ((x) << 8)
#define PROC_CMD_FIBER_PORT(x) (0x0100 << (x) % 4)
#define PROC_CMD_QSGMII_PORT 0x0c00
#define PROC_CMD_RST_CONF_PORT 0x0080
#define PROC_CMD_RECONF_PORT 0x0000
#define PROC_CMD_READ_MOD_WRITE_PORT 0x0040
#define PROC_CMD_WRITE 0x0040
#define PROC_CMD_READ 0x0000
#define PROC_CMD_FIBER_DISABLE 0x0020
#define PROC_CMD_FIBER_100BASE_FX 0x0010
#define PROC_CMD_FIBER_1000BASE_X 0x0000
#define PROC_CMD_SGMII_MAC 0x0030
#define PROC_CMD_QSGMII_MAC 0x0020
#define PROC_CMD_NO_MAC_CONF 0x0000
net: phy: mscc: add support for VSC8574 PHY The VSC8574 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports WOL, downshifting and can set the blinking pattern of each of its 4 LEDs, supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, WOL, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8574 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:43 +07:00
#define PROC_CMD_1588_DEFAULT_INIT 0x0010
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
#define PROC_CMD_NOP 0x000f
net: phy: mscc: add support for VSC8574 PHY The VSC8574 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports WOL, downshifting and can set the blinking pattern of each of its 4 LEDs, supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, WOL, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8574 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:43 +07:00
#define PROC_CMD_PHY_INIT 0x000a
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
#define PROC_CMD_CRC16 0x0008
#define PROC_CMD_FIBER_MEDIA_CONF 0x0001
#define PROC_CMD_MCB_ACCESS_MAC_CONF 0x0000
#define PROC_CMD_NCOMPLETED_TIMEOUT_MS 500
#define MSCC_PHY_MAC_CFG_FASTLINK 19
#define MAC_CFG_MASK 0xc000
#define MAC_CFG_SGMII 0x0000
#define MAC_CFG_QSGMII 0x4000
/* Test page Registers */
#define MSCC_PHY_TEST_PAGE_5 5
#define MSCC_PHY_TEST_PAGE_8 8
net: phy: mscc: add support for VSC8574 PHY The VSC8574 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports WOL, downshifting and can set the blinking pattern of each of its 4 LEDs, supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, WOL, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8574 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:43 +07:00
#define MSCC_PHY_TEST_PAGE_9 9
#define MSCC_PHY_TEST_PAGE_20 20
#define MSCC_PHY_TEST_PAGE_24 24
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
/* Token ring page Registers */
#define MSCC_PHY_TR_CNTL 16
#define TR_WRITE 0x8000
#define TR_ADDR(x) (0x7fff & (x))
#define MSCC_PHY_TR_LSB 17
#define MSCC_PHY_TR_MSB 18
/* Microsemi PHY ID's
* Code assumes lowest nibble is 0
*/
#define PHY_ID_VSC8504 0x000704c0
net: phy: mscc: add support for VSC8514 PHY. The VSC8514 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X, can communicate with the MAC via QSGMII. The MAC interface protocol for each port within QSGMII can be either 1000BASE-X or SGMII, if the QSGMII MAC that the VSC8514 is connecting to supports this functionality. VSC8514 also supports SGMII MAC-side autonegotiation on each individual port, downshifting, can set the blinking pattern of each of its 4 LEDs, SyncE, 1000BASE-T Ring Resiliency as well as HP Auto-MDIX detection. This adds support for 10BASE-T, 100BASE-TX, and 1000BASE-T, QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. Signed-off-by: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com> Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Co-developed-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-22 18:51:35 +07:00
#define PHY_ID_VSC8514 0x00070670
#define PHY_ID_VSC8530 0x00070560
#define PHY_ID_VSC8531 0x00070570
#define PHY_ID_VSC8540 0x00070760
#define PHY_ID_VSC8541 0x00070770
#define PHY_ID_VSC8552 0x000704e0
#define PHY_ID_VSC856X 0x000707e0
#define PHY_ID_VSC8572 0x000704d0
net: phy: mscc: add support for VSC8574 PHY The VSC8574 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports WOL, downshifting and can set the blinking pattern of each of its 4 LEDs, supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, WOL, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8574 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:43 +07:00
#define PHY_ID_VSC8574 0x000704a0
#define PHY_ID_VSC8575 0x000707d0
#define PHY_ID_VSC8582 0x000707b0
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
#define PHY_ID_VSC8584 0x000707c0
#define MSCC_VDDMAC_1500 1500
#define MSCC_VDDMAC_1800 1800
#define MSCC_VDDMAC_2500 2500
#define MSCC_VDDMAC_3300 3300
#define DOWNSHIFT_COUNT_MAX 5
#define MAX_LEDS 4
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
#define VSC8584_SUPP_LED_MODES (BIT(VSC8531_LINK_ACTIVITY) | \
BIT(VSC8531_LINK_1000_ACTIVITY) | \
BIT(VSC8531_LINK_100_ACTIVITY) | \
BIT(VSC8531_LINK_10_ACTIVITY) | \
BIT(VSC8531_LINK_100_1000_ACTIVITY) | \
BIT(VSC8531_LINK_10_1000_ACTIVITY) | \
BIT(VSC8531_LINK_10_100_ACTIVITY) | \
BIT(VSC8584_LINK_100FX_1000X_ACTIVITY) | \
BIT(VSC8531_DUPLEX_COLLISION) | \
BIT(VSC8531_COLLISION) | \
BIT(VSC8531_ACTIVITY) | \
BIT(VSC8584_100FX_1000X_ACTIVITY) | \
BIT(VSC8531_AUTONEG_FAULT) | \
BIT(VSC8531_SERIAL_MODE) | \
BIT(VSC8531_FORCE_LED_OFF) | \
BIT(VSC8531_FORCE_LED_ON))
#define VSC85XX_SUPP_LED_MODES (BIT(VSC8531_LINK_ACTIVITY) | \
BIT(VSC8531_LINK_1000_ACTIVITY) | \
BIT(VSC8531_LINK_100_ACTIVITY) | \
BIT(VSC8531_LINK_10_ACTIVITY) | \
BIT(VSC8531_LINK_100_1000_ACTIVITY) | \
BIT(VSC8531_LINK_10_1000_ACTIVITY) | \
BIT(VSC8531_LINK_10_100_ACTIVITY) | \
BIT(VSC8531_DUPLEX_COLLISION) | \
BIT(VSC8531_COLLISION) | \
BIT(VSC8531_ACTIVITY) | \
BIT(VSC8531_AUTONEG_FAULT) | \
BIT(VSC8531_SERIAL_MODE) | \
BIT(VSC8531_FORCE_LED_OFF) | \
BIT(VSC8531_FORCE_LED_ON))
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
#define MSCC_VSC8584_REVB_INT8051_FW "mscc_vsc8584_revb_int8051_fb48.bin"
#define MSCC_VSC8584_REVB_INT8051_FW_START_ADDR 0xe800
#define MSCC_VSC8584_REVB_INT8051_FW_CRC 0xfb48
net: phy: mscc: add support for VSC8574 PHY The VSC8574 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports WOL, downshifting and can set the blinking pattern of each of its 4 LEDs, supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, WOL, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8574 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:43 +07:00
#define MSCC_VSC8574_REVB_INT8051_FW "mscc_vsc8574_revb_int8051_29e8.bin"
#define MSCC_VSC8574_REVB_INT8051_FW_START_ADDR 0x4000
#define MSCC_VSC8574_REVB_INT8051_FW_CRC 0x29e8
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
#define VSC8584_REVB 0x0001
#define MSCC_DEV_REV_MASK GENMASK(3, 0)
struct reg_val {
u16 reg;
u32 val;
};
struct vsc85xx_hw_stat {
const char *string;
u8 reg;
u16 page;
u16 mask;
};
static const struct vsc85xx_hw_stat vsc85xx_hw_stats[] = {
{
.string = "phy_receive_errors",
.reg = MSCC_PHY_ERR_RX_CNT,
.page = MSCC_PHY_PAGE_STANDARD,
.mask = ERR_CNT_MASK,
}, {
.string = "phy_false_carrier",
.reg = MSCC_PHY_ERR_FALSE_CARRIER_CNT,
.page = MSCC_PHY_PAGE_STANDARD,
.mask = ERR_CNT_MASK,
}, {
.string = "phy_cu_media_link_disconnect",
.reg = MSCC_PHY_ERR_LINK_DISCONNECT_CNT,
.page = MSCC_PHY_PAGE_STANDARD,
.mask = ERR_CNT_MASK,
}, {
.string = "phy_cu_media_crc_good_count",
.reg = MSCC_PHY_CU_MEDIA_CRC_VALID_CNT,
.page = MSCC_PHY_PAGE_EXTENDED,
.mask = VALID_CRC_CNT_CRC_MASK,
}, {
.string = "phy_cu_media_crc_error_count",
.reg = MSCC_PHY_EXT_PHY_CNTL_4,
.page = MSCC_PHY_PAGE_EXTENDED,
.mask = ERR_CNT_MASK,
},
};
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
static const struct vsc85xx_hw_stat vsc8584_hw_stats[] = {
{
.string = "phy_receive_errors",
.reg = MSCC_PHY_ERR_RX_CNT,
.page = MSCC_PHY_PAGE_STANDARD,
.mask = ERR_CNT_MASK,
}, {
.string = "phy_false_carrier",
.reg = MSCC_PHY_ERR_FALSE_CARRIER_CNT,
.page = MSCC_PHY_PAGE_STANDARD,
.mask = ERR_CNT_MASK,
}, {
.string = "phy_cu_media_link_disconnect",
.reg = MSCC_PHY_ERR_LINK_DISCONNECT_CNT,
.page = MSCC_PHY_PAGE_STANDARD,
.mask = ERR_CNT_MASK,
}, {
.string = "phy_cu_media_crc_good_count",
.reg = MSCC_PHY_CU_MEDIA_CRC_VALID_CNT,
.page = MSCC_PHY_PAGE_EXTENDED,
.mask = VALID_CRC_CNT_CRC_MASK,
}, {
.string = "phy_cu_media_crc_error_count",
.reg = MSCC_PHY_EXT_PHY_CNTL_4,
.page = MSCC_PHY_PAGE_EXTENDED,
.mask = ERR_CNT_MASK,
}, {
.string = "phy_serdes_tx_good_pkt_count",
.reg = MSCC_PHY_SERDES_TX_VALID_CNT,
.page = MSCC_PHY_PAGE_EXTENDED_3,
.mask = VALID_CRC_CNT_CRC_MASK,
}, {
.string = "phy_serdes_tx_bad_crc_count",
.reg = MSCC_PHY_SERDES_TX_CRC_ERR_CNT,
.page = MSCC_PHY_PAGE_EXTENDED_3,
.mask = ERR_CNT_MASK,
}, {
.string = "phy_serdes_rx_good_pkt_count",
.reg = MSCC_PHY_SERDES_RX_VALID_CNT,
.page = MSCC_PHY_PAGE_EXTENDED_3,
.mask = VALID_CRC_CNT_CRC_MASK,
}, {
.string = "phy_serdes_rx_bad_crc_count",
.reg = MSCC_PHY_SERDES_RX_CRC_ERR_CNT,
.page = MSCC_PHY_PAGE_EXTENDED_3,
.mask = ERR_CNT_MASK,
},
};
#if IS_ENABLED(CONFIG_MACSEC)
struct macsec_flow {
struct list_head list;
enum mscc_macsec_destination_ports port;
enum macsec_bank bank;
u32 index;
int assoc_num;
bool has_transformation;
/* Highest takes precedence [0..15] */
u8 priority;
u8 key[MACSEC_KEYID_LEN];
union {
struct macsec_rx_sa *rx_sa;
struct macsec_tx_sa *tx_sa;
};
/* Matching */
struct {
u8 sci:1;
u8 tagged:1;
u8 untagged:1;
u8 etype:1;
} match;
u16 etype;
/* Action */
struct {
u8 bypass:1;
u8 drop:1;
} action;
};
#endif
struct vsc8531_private {
int rate_magic;
u16 supp_led_modes;
u32 leds_mode[MAX_LEDS];
u8 nleds;
const struct vsc85xx_hw_stat *hw_stats;
u64 *stats;
int nstats;
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
bool pkg_init;
/* For multiple port PHYs; the MDIO address of the base PHY in the
* package.
*/
unsigned int base_addr;
#if IS_ENABLED(CONFIG_MACSEC)
/* MACsec fields:
* - One SecY per device (enforced at the s/w implementation level)
* - macsec_flows: list of h/w flows
* - ingr_flows: bitmap of ingress flows
* - egr_flows: bitmap of egress flows
*/
struct macsec_secy *secy;
struct list_head macsec_flows;
unsigned long ingr_flows;
unsigned long egr_flows;
#endif
};
#ifdef CONFIG_OF_MDIO
struct vsc8531_edge_rate_table {
u32 vddmac;
u32 slowdown[8];
};
static const struct vsc8531_edge_rate_table edge_table[] = {
{MSCC_VDDMAC_3300, { 0, 2, 4, 7, 10, 17, 29, 53} },
{MSCC_VDDMAC_2500, { 0, 3, 6, 10, 14, 23, 37, 63} },
{MSCC_VDDMAC_1800, { 0, 5, 9, 16, 23, 35, 52, 76} },
{MSCC_VDDMAC_1500, { 0, 6, 14, 21, 29, 42, 58, 77} },
};
#endif /* CONFIG_OF_MDIO */
static int vsc85xx_phy_read_page(struct phy_device *phydev)
{
return __phy_read(phydev, MSCC_EXT_PAGE_ACCESS);
}
static int vsc85xx_phy_write_page(struct phy_device *phydev, int page)
{
return __phy_write(phydev, MSCC_EXT_PAGE_ACCESS, page);
}
static int vsc85xx_get_sset_count(struct phy_device *phydev)
{
struct vsc8531_private *priv = phydev->priv;
if (!priv)
return 0;
return priv->nstats;
}
static void vsc85xx_get_strings(struct phy_device *phydev, u8 *data)
{
struct vsc8531_private *priv = phydev->priv;
int i;
if (!priv)
return;
for (i = 0; i < priv->nstats; i++)
strlcpy(data + i * ETH_GSTRING_LEN, priv->hw_stats[i].string,
ETH_GSTRING_LEN);
}
static u64 vsc85xx_get_stat(struct phy_device *phydev, int i)
{
struct vsc8531_private *priv = phydev->priv;
int val;
val = phy_read_paged(phydev, priv->hw_stats[i].page,
priv->hw_stats[i].reg);
if (val < 0)
return U64_MAX;
val = val & priv->hw_stats[i].mask;
priv->stats[i] += val;
return priv->stats[i];
}
static void vsc85xx_get_stats(struct phy_device *phydev,
struct ethtool_stats *stats, u64 *data)
{
struct vsc8531_private *priv = phydev->priv;
int i;
if (!priv)
return;
for (i = 0; i < priv->nstats; i++)
data[i] = vsc85xx_get_stat(phydev, i);
}
static int vsc85xx_led_cntl_set(struct phy_device *phydev,
u8 led_num,
u8 mode)
{
int rc;
u16 reg_val;
mutex_lock(&phydev->lock);
reg_val = phy_read(phydev, MSCC_PHY_LED_MODE_SEL);
reg_val &= ~LED_MODE_SEL_MASK(led_num);
reg_val |= LED_MODE_SEL(led_num, (u16)mode);
rc = phy_write(phydev, MSCC_PHY_LED_MODE_SEL, reg_val);
mutex_unlock(&phydev->lock);
return rc;
}
static int vsc85xx_mdix_get(struct phy_device *phydev, u8 *mdix)
{
u16 reg_val;
reg_val = phy_read(phydev, MSCC_PHY_DEV_AUX_CNTL);
if (reg_val & HP_AUTO_MDIX_X_OVER_IND_MASK)
*mdix = ETH_TP_MDI_X;
else
*mdix = ETH_TP_MDI;
return 0;
}
static int vsc85xx_mdix_set(struct phy_device *phydev, u8 mdix)
{
int rc;
u16 reg_val;
reg_val = phy_read(phydev, MSCC_PHY_BYPASS_CONTROL);
if (mdix == ETH_TP_MDI || mdix == ETH_TP_MDI_X) {
reg_val |= (DISABLE_PAIR_SWAP_CORR_MASK |
DISABLE_POLARITY_CORR_MASK |
DISABLE_HP_AUTO_MDIX_MASK);
} else {
reg_val &= ~(DISABLE_PAIR_SWAP_CORR_MASK |
DISABLE_POLARITY_CORR_MASK |
DISABLE_HP_AUTO_MDIX_MASK);
}
rc = phy_write(phydev, MSCC_PHY_BYPASS_CONTROL, reg_val);
if (rc)
return rc;
reg_val = 0;
if (mdix == ETH_TP_MDI)
reg_val = FORCE_MDI_CROSSOVER_MDI;
else if (mdix == ETH_TP_MDI_X)
reg_val = FORCE_MDI_CROSSOVER_MDIX;
rc = phy_modify_paged(phydev, MSCC_PHY_PAGE_EXTENDED,
MSCC_PHY_EXT_MODE_CNTL, FORCE_MDI_CROSSOVER_MASK,
reg_val);
if (rc < 0)
return rc;
return genphy_restart_aneg(phydev);
}
static int vsc85xx_downshift_get(struct phy_device *phydev, u8 *count)
{
int reg_val;
reg_val = phy_read_paged(phydev, MSCC_PHY_PAGE_EXTENDED,
MSCC_PHY_ACTIPHY_CNTL);
if (reg_val < 0)
return reg_val;
reg_val &= DOWNSHIFT_CNTL_MASK;
if (!(reg_val & DOWNSHIFT_EN))
*count = DOWNSHIFT_DEV_DISABLE;
else
*count = ((reg_val & ~DOWNSHIFT_EN) >> DOWNSHIFT_CNTL_POS) + 2;
return 0;
}
static int vsc85xx_downshift_set(struct phy_device *phydev, u8 count)
{
if (count == DOWNSHIFT_DEV_DEFAULT_COUNT) {
/* Default downshift count 3 (i.e. Bit3:2 = 0b01) */
count = ((1 << DOWNSHIFT_CNTL_POS) | DOWNSHIFT_EN);
} else if (count > DOWNSHIFT_COUNT_MAX || count == 1) {
phydev_err(phydev, "Downshift count should be 2,3,4 or 5\n");
return -ERANGE;
} else if (count) {
/* Downshift count is either 2,3,4 or 5 */
count = (((count - 2) << DOWNSHIFT_CNTL_POS) | DOWNSHIFT_EN);
}
return phy_modify_paged(phydev, MSCC_PHY_PAGE_EXTENDED,
MSCC_PHY_ACTIPHY_CNTL, DOWNSHIFT_CNTL_MASK,
count);
}
static int vsc85xx_wol_set(struct phy_device *phydev,
struct ethtool_wolinfo *wol)
{
int rc;
u16 reg_val;
u8 i;
u16 pwd[3] = {0, 0, 0};
struct ethtool_wolinfo *wol_conf = wol;
u8 *mac_addr = phydev->attached_dev->dev_addr;
mutex_lock(&phydev->lock);
rc = phy_select_page(phydev, MSCC_PHY_PAGE_EXTENDED_2);
if (rc < 0) {
rc = phy_restore_page(phydev, rc, rc);
goto out_unlock;
}
if (wol->wolopts & WAKE_MAGIC) {
/* Store the device address for the magic packet */
for (i = 0; i < ARRAY_SIZE(pwd); i++)
pwd[i] = mac_addr[5 - (i * 2 + 1)] << 8 |
mac_addr[5 - i * 2];
__phy_write(phydev, MSCC_PHY_WOL_LOWER_MAC_ADDR, pwd[0]);
__phy_write(phydev, MSCC_PHY_WOL_MID_MAC_ADDR, pwd[1]);
__phy_write(phydev, MSCC_PHY_WOL_UPPER_MAC_ADDR, pwd[2]);
} else {
__phy_write(phydev, MSCC_PHY_WOL_LOWER_MAC_ADDR, 0);
__phy_write(phydev, MSCC_PHY_WOL_MID_MAC_ADDR, 0);
__phy_write(phydev, MSCC_PHY_WOL_UPPER_MAC_ADDR, 0);
}
if (wol_conf->wolopts & WAKE_MAGICSECURE) {
for (i = 0; i < ARRAY_SIZE(pwd); i++)
pwd[i] = wol_conf->sopass[5 - (i * 2 + 1)] << 8 |
wol_conf->sopass[5 - i * 2];
__phy_write(phydev, MSCC_PHY_WOL_LOWER_PASSWD, pwd[0]);
__phy_write(phydev, MSCC_PHY_WOL_MID_PASSWD, pwd[1]);
__phy_write(phydev, MSCC_PHY_WOL_UPPER_PASSWD, pwd[2]);
} else {
__phy_write(phydev, MSCC_PHY_WOL_LOWER_PASSWD, 0);
__phy_write(phydev, MSCC_PHY_WOL_MID_PASSWD, 0);
__phy_write(phydev, MSCC_PHY_WOL_UPPER_PASSWD, 0);
}
reg_val = __phy_read(phydev, MSCC_PHY_WOL_MAC_CONTROL);
if (wol_conf->wolopts & WAKE_MAGICSECURE)
reg_val |= SECURE_ON_ENABLE;
else
reg_val &= ~SECURE_ON_ENABLE;
__phy_write(phydev, MSCC_PHY_WOL_MAC_CONTROL, reg_val);
rc = phy_restore_page(phydev, rc, rc > 0 ? 0 : rc);
if (rc < 0)
goto out_unlock;
if (wol->wolopts & WAKE_MAGIC) {
/* Enable the WOL interrupt */
reg_val = phy_read(phydev, MII_VSC85XX_INT_MASK);
reg_val |= MII_VSC85XX_INT_MASK_WOL;
rc = phy_write(phydev, MII_VSC85XX_INT_MASK, reg_val);
if (rc)
goto out_unlock;
} else {
/* Disable the WOL interrupt */
reg_val = phy_read(phydev, MII_VSC85XX_INT_MASK);
reg_val &= (~MII_VSC85XX_INT_MASK_WOL);
rc = phy_write(phydev, MII_VSC85XX_INT_MASK, reg_val);
if (rc)
goto out_unlock;
}
/* Clear WOL iterrupt status */
reg_val = phy_read(phydev, MII_VSC85XX_INT_STATUS);
out_unlock:
mutex_unlock(&phydev->lock);
return rc;
}
static void vsc85xx_wol_get(struct phy_device *phydev,
struct ethtool_wolinfo *wol)
{
int rc;
u16 reg_val;
u8 i;
u16 pwd[3] = {0, 0, 0};
struct ethtool_wolinfo *wol_conf = wol;
mutex_lock(&phydev->lock);
rc = phy_select_page(phydev, MSCC_PHY_PAGE_EXTENDED_2);
if (rc < 0)
goto out_unlock;
reg_val = __phy_read(phydev, MSCC_PHY_WOL_MAC_CONTROL);
if (reg_val & SECURE_ON_ENABLE)
wol_conf->wolopts |= WAKE_MAGICSECURE;
if (wol_conf->wolopts & WAKE_MAGICSECURE) {
pwd[0] = __phy_read(phydev, MSCC_PHY_WOL_LOWER_PASSWD);
pwd[1] = __phy_read(phydev, MSCC_PHY_WOL_MID_PASSWD);
pwd[2] = __phy_read(phydev, MSCC_PHY_WOL_UPPER_PASSWD);
for (i = 0; i < ARRAY_SIZE(pwd); i++) {
wol_conf->sopass[5 - i * 2] = pwd[i] & 0x00ff;
wol_conf->sopass[5 - (i * 2 + 1)] = (pwd[i] & 0xff00)
>> 8;
}
}
out_unlock:
phy_restore_page(phydev, rc, rc > 0 ? 0 : rc);
mutex_unlock(&phydev->lock);
}
#ifdef CONFIG_OF_MDIO
static int vsc85xx_edge_rate_magic_get(struct phy_device *phydev)
{
u32 vdd, sd;
int i, j;
struct device *dev = &phydev->mdio.dev;
struct device_node *of_node = dev->of_node;
u8 sd_array_size = ARRAY_SIZE(edge_table[0].slowdown);
if (!of_node)
return -ENODEV;
if (of_property_read_u32(of_node, "vsc8531,vddmac", &vdd))
vdd = MSCC_VDDMAC_3300;
if (of_property_read_u32(of_node, "vsc8531,edge-slowdown", &sd))
sd = 0;
for (i = 0; i < ARRAY_SIZE(edge_table); i++)
if (edge_table[i].vddmac == vdd)
for (j = 0; j < sd_array_size; j++)
if (edge_table[i].slowdown[j] == sd)
return (sd_array_size - j - 1);
return -EINVAL;
}
static int vsc85xx_dt_led_mode_get(struct phy_device *phydev,
char *led,
u32 default_mode)
{
struct vsc8531_private *priv = phydev->priv;
struct device *dev = &phydev->mdio.dev;
struct device_node *of_node = dev->of_node;
u32 led_mode;
int err;
if (!of_node)
return -ENODEV;
led_mode = default_mode;
err = of_property_read_u32(of_node, led, &led_mode);
if (!err && !(BIT(led_mode) & priv->supp_led_modes)) {
phydev_err(phydev, "DT %s invalid\n", led);
return -EINVAL;
}
return led_mode;
}
#else
static int vsc85xx_edge_rate_magic_get(struct phy_device *phydev)
{
return 0;
}
static int vsc85xx_dt_led_mode_get(struct phy_device *phydev,
char *led,
u8 default_mode)
{
return default_mode;
}
#endif /* CONFIG_OF_MDIO */
static int vsc85xx_dt_led_modes_get(struct phy_device *phydev,
u32 *default_mode)
{
struct vsc8531_private *priv = phydev->priv;
char led_dt_prop[28];
int i, ret;
for (i = 0; i < priv->nleds; i++) {
ret = sprintf(led_dt_prop, "vsc8531,led-%d-mode", i);
if (ret < 0)
return ret;
ret = vsc85xx_dt_led_mode_get(phydev, led_dt_prop,
default_mode[i]);
if (ret < 0)
return ret;
priv->leds_mode[i] = ret;
}
return 0;
}
static int vsc85xx_edge_rate_cntl_set(struct phy_device *phydev, u8 edge_rate)
{
int rc;
mutex_lock(&phydev->lock);
rc = phy_modify_paged(phydev, MSCC_PHY_PAGE_EXTENDED_2,
MSCC_PHY_WOL_MAC_CONTROL, EDGE_RATE_CNTL_MASK,
edge_rate << EDGE_RATE_CNTL_POS);
mutex_unlock(&phydev->lock);
return rc;
}
static int vsc85xx_mac_if_set(struct phy_device *phydev,
phy_interface_t interface)
{
int rc;
u16 reg_val;
mutex_lock(&phydev->lock);
reg_val = phy_read(phydev, MSCC_PHY_EXT_PHY_CNTL_1);
reg_val &= ~(MAC_IF_SELECTION_MASK);
switch (interface) {
case PHY_INTERFACE_MODE_RGMII:
reg_val |= (MAC_IF_SELECTION_RGMII << MAC_IF_SELECTION_POS);
break;
case PHY_INTERFACE_MODE_RMII:
reg_val |= (MAC_IF_SELECTION_RMII << MAC_IF_SELECTION_POS);
break;
case PHY_INTERFACE_MODE_MII:
case PHY_INTERFACE_MODE_GMII:
reg_val |= (MAC_IF_SELECTION_GMII << MAC_IF_SELECTION_POS);
break;
default:
rc = -EINVAL;
goto out_unlock;
}
rc = phy_write(phydev, MSCC_PHY_EXT_PHY_CNTL_1, reg_val);
if (rc)
goto out_unlock;
rc = genphy_soft_reset(phydev);
out_unlock:
mutex_unlock(&phydev->lock);
return rc;
}
static int vsc85xx_default_config(struct phy_device *phydev)
{
int rc;
u16 reg_val;
phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
mutex_lock(&phydev->lock);
reg_val = RGMII_RX_CLK_DELAY_1_1_NS << RGMII_RX_CLK_DELAY_POS;
rc = phy_modify_paged(phydev, MSCC_PHY_PAGE_EXTENDED_2,
MSCC_PHY_RGMII_CNTL, RGMII_RX_CLK_DELAY_MASK,
reg_val);
mutex_unlock(&phydev->lock);
return rc;
}
static int vsc85xx_get_tunable(struct phy_device *phydev,
struct ethtool_tunable *tuna, void *data)
{
switch (tuna->id) {
case ETHTOOL_PHY_DOWNSHIFT:
return vsc85xx_downshift_get(phydev, (u8 *)data);
default:
return -EINVAL;
}
}
static int vsc85xx_set_tunable(struct phy_device *phydev,
struct ethtool_tunable *tuna,
const void *data)
{
switch (tuna->id) {
case ETHTOOL_PHY_DOWNSHIFT:
return vsc85xx_downshift_set(phydev, *(u8 *)data);
default:
return -EINVAL;
}
}
/* mdiobus lock should be locked when using this function */
static void vsc85xx_tr_write(struct phy_device *phydev, u16 addr, u32 val)
{
__phy_write(phydev, MSCC_PHY_TR_MSB, val >> 16);
__phy_write(phydev, MSCC_PHY_TR_LSB, val & GENMASK(15, 0));
__phy_write(phydev, MSCC_PHY_TR_CNTL, TR_WRITE | TR_ADDR(addr));
}
static int vsc8531_pre_init_seq_set(struct phy_device *phydev)
{
int rc;
static const struct reg_val init_seq[] = {
{0x0f90, 0x00688980},
{0x0696, 0x00000003},
{0x07fa, 0x0050100f},
{0x1686, 0x00000004},
};
unsigned int i;
int oldpage;
rc = phy_modify_paged(phydev, MSCC_PHY_PAGE_STANDARD,
MSCC_PHY_EXT_CNTL_STATUS, SMI_BROADCAST_WR_EN,
SMI_BROADCAST_WR_EN);
if (rc < 0)
return rc;
rc = phy_modify_paged(phydev, MSCC_PHY_PAGE_TEST,
MSCC_PHY_TEST_PAGE_24, 0, 0x0400);
if (rc < 0)
return rc;
rc = phy_modify_paged(phydev, MSCC_PHY_PAGE_TEST,
MSCC_PHY_TEST_PAGE_5, 0x0a00, 0x0e00);
if (rc < 0)
return rc;
rc = phy_modify_paged(phydev, MSCC_PHY_PAGE_TEST,
MSCC_PHY_TEST_PAGE_8, 0x8000, 0x8000);
if (rc < 0)
return rc;
mutex_lock(&phydev->lock);
oldpage = phy_select_page(phydev, MSCC_PHY_PAGE_TR);
if (oldpage < 0)
goto out_unlock;
for (i = 0; i < ARRAY_SIZE(init_seq); i++)
vsc85xx_tr_write(phydev, init_seq[i].reg, init_seq[i].val);
out_unlock:
oldpage = phy_restore_page(phydev, oldpage, oldpage);
mutex_unlock(&phydev->lock);
return oldpage;
}
static int vsc85xx_eee_init_seq_set(struct phy_device *phydev)
{
static const struct reg_val init_eee[] = {
{0x0f82, 0x0012b00a},
{0x1686, 0x00000004},
{0x168c, 0x00d2c46f},
{0x17a2, 0x00000620},
{0x16a0, 0x00eeffdd},
{0x16a6, 0x00071448},
{0x16a4, 0x0013132f},
{0x16a8, 0x00000000},
{0x0ffc, 0x00c0a028},
{0x0fe8, 0x0091b06c},
{0x0fea, 0x00041600},
{0x0f80, 0x00000af4},
{0x0fec, 0x00901809},
{0x0fee, 0x0000a6a1},
{0x0ffe, 0x00b01007},
{0x16b0, 0x00eeff00},
{0x16b2, 0x00007000},
{0x16b4, 0x00000814},
};
unsigned int i;
int oldpage;
mutex_lock(&phydev->lock);
oldpage = phy_select_page(phydev, MSCC_PHY_PAGE_TR);
if (oldpage < 0)
goto out_unlock;
for (i = 0; i < ARRAY_SIZE(init_eee); i++)
vsc85xx_tr_write(phydev, init_eee[i].reg, init_eee[i].val);
out_unlock:
oldpage = phy_restore_page(phydev, oldpage, oldpage);
mutex_unlock(&phydev->lock);
return oldpage;
}
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
/* phydev->bus->mdio_lock should be locked when using this function */
static int phy_base_write(struct phy_device *phydev, u32 regnum, u16 val)
{
struct vsc8531_private *priv = phydev->priv;
if (unlikely(!mutex_is_locked(&phydev->mdio.bus->mdio_lock))) {
dev_err(&phydev->mdio.dev, "MDIO bus lock not held!\n");
dump_stack();
}
return __mdiobus_write(phydev->mdio.bus, priv->base_addr, regnum, val);
}
/* phydev->bus->mdio_lock should be locked when using this function */
static int phy_base_read(struct phy_device *phydev, u32 regnum)
{
struct vsc8531_private *priv = phydev->priv;
if (unlikely(!mutex_is_locked(&phydev->mdio.bus->mdio_lock))) {
dev_err(&phydev->mdio.dev, "MDIO bus lock not held!\n");
dump_stack();
}
return __mdiobus_read(phydev->mdio.bus, priv->base_addr, regnum);
}
/* bus->mdio_lock should be locked when using this function */
static void vsc8584_csr_write(struct phy_device *phydev, u16 addr, u32 val)
{
phy_base_write(phydev, MSCC_PHY_TR_MSB, val >> 16);
phy_base_write(phydev, MSCC_PHY_TR_LSB, val & GENMASK(15, 0));
phy_base_write(phydev, MSCC_PHY_TR_CNTL, TR_WRITE | TR_ADDR(addr));
}
/* bus->mdio_lock should be locked when using this function */
static int vsc8584_cmd(struct phy_device *phydev, u16 val)
{
unsigned long deadline;
u16 reg_val;
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS,
MSCC_PHY_PAGE_EXTENDED_GPIO);
phy_base_write(phydev, MSCC_PHY_PROC_CMD, PROC_CMD_NCOMPLETED | val);
deadline = jiffies + msecs_to_jiffies(PROC_CMD_NCOMPLETED_TIMEOUT_MS);
do {
reg_val = phy_base_read(phydev, MSCC_PHY_PROC_CMD);
} while (time_before(jiffies, deadline) &&
(reg_val & PROC_CMD_NCOMPLETED) &&
!(reg_val & PROC_CMD_FAILED));
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
if (reg_val & PROC_CMD_FAILED)
return -EIO;
if (reg_val & PROC_CMD_NCOMPLETED)
return -ETIMEDOUT;
return 0;
}
/* bus->mdio_lock should be locked when using this function */
static int vsc8584_micro_deassert_reset(struct phy_device *phydev,
bool patch_en)
{
u32 enable, release;
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS,
MSCC_PHY_PAGE_EXTENDED_GPIO);
enable = RUN_FROM_INT_ROM | MICRO_CLK_EN | DW8051_CLK_EN;
release = MICRO_NSOFT_RESET | RUN_FROM_INT_ROM | DW8051_CLK_EN |
MICRO_CLK_EN;
if (patch_en) {
enable |= MICRO_PATCH_EN;
release |= MICRO_PATCH_EN;
/* Clear all patches */
phy_base_write(phydev, MSCC_INT_MEM_CNTL, READ_RAM);
}
/* Enable 8051 Micro clock; CLEAR/SET patch present; disable PRAM clock
* override and addr. auto-incr; operate at 125 MHz
*/
phy_base_write(phydev, MSCC_DW8051_CNTL_STATUS, enable);
/* Release 8051 Micro SW reset */
phy_base_write(phydev, MSCC_DW8051_CNTL_STATUS, release);
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
return 0;
}
/* bus->mdio_lock should be locked when using this function */
static int vsc8584_micro_assert_reset(struct phy_device *phydev)
{
int ret;
u16 reg;
ret = vsc8584_cmd(phydev, PROC_CMD_NOP);
if (ret)
return ret;
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS,
MSCC_PHY_PAGE_EXTENDED_GPIO);
reg = phy_base_read(phydev, MSCC_INT_MEM_CNTL);
reg &= ~EN_PATCH_RAM_TRAP_ADDR(4);
phy_base_write(phydev, MSCC_INT_MEM_CNTL, reg);
phy_base_write(phydev, MSCC_TRAP_ROM_ADDR(4), 0x005b);
phy_base_write(phydev, MSCC_PATCH_RAM_ADDR(4), 0x005b);
reg = phy_base_read(phydev, MSCC_INT_MEM_CNTL);
reg |= EN_PATCH_RAM_TRAP_ADDR(4);
phy_base_write(phydev, MSCC_INT_MEM_CNTL, reg);
phy_base_write(phydev, MSCC_PHY_PROC_CMD, PROC_CMD_NOP);
reg = phy_base_read(phydev, MSCC_DW8051_CNTL_STATUS);
reg &= ~MICRO_NSOFT_RESET;
phy_base_write(phydev, MSCC_DW8051_CNTL_STATUS, reg);
phy_base_write(phydev, MSCC_PHY_PROC_CMD, PROC_CMD_MCB_ACCESS_MAC_CONF |
PROC_CMD_SGMII_PORT(0) | PROC_CMD_NO_MAC_CONF |
PROC_CMD_READ);
reg = phy_base_read(phydev, MSCC_INT_MEM_CNTL);
reg &= ~EN_PATCH_RAM_TRAP_ADDR(4);
phy_base_write(phydev, MSCC_INT_MEM_CNTL, reg);
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
return 0;
}
/* bus->mdio_lock should be locked when using this function */
static int vsc8584_get_fw_crc(struct phy_device *phydev, u16 start, u16 size,
u16 *crc)
{
int ret;
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_EXTENDED);
phy_base_write(phydev, MSCC_PHY_VERIPHY_CNTL_2, start);
phy_base_write(phydev, MSCC_PHY_VERIPHY_CNTL_3, size);
/* Start Micro command */
ret = vsc8584_cmd(phydev, PROC_CMD_CRC16);
if (ret)
goto out;
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_EXTENDED);
*crc = phy_base_read(phydev, MSCC_PHY_VERIPHY_CNTL_2);
out:
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
return ret;
}
/* bus->mdio_lock should be locked when using this function */
static int vsc8584_patch_fw(struct phy_device *phydev,
const struct firmware *fw)
{
int i, ret;
ret = vsc8584_micro_assert_reset(phydev);
if (ret) {
dev_err(&phydev->mdio.dev,
"%s: failed to assert reset of micro\n", __func__);
return ret;
}
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS,
MSCC_PHY_PAGE_EXTENDED_GPIO);
/* Hold 8051 Micro in SW Reset, Enable auto incr address and patch clock
* Disable the 8051 Micro clock
*/
phy_base_write(phydev, MSCC_DW8051_CNTL_STATUS, RUN_FROM_INT_ROM |
AUTOINC_ADDR | PATCH_RAM_CLK | MICRO_CLK_EN |
MICRO_CLK_DIVIDE(2));
phy_base_write(phydev, MSCC_INT_MEM_CNTL, READ_PRAM | INT_MEM_WRITE_EN |
INT_MEM_DATA(2));
phy_base_write(phydev, MSCC_INT_MEM_ADDR, 0x0000);
for (i = 0; i < fw->size; i++)
phy_base_write(phydev, MSCC_INT_MEM_CNTL, READ_PRAM |
INT_MEM_WRITE_EN | fw->data[i]);
/* Clear internal memory access */
phy_base_write(phydev, MSCC_INT_MEM_CNTL, READ_RAM);
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
return 0;
}
net: phy: mscc: add support for VSC8574 PHY The VSC8574 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports WOL, downshifting and can set the blinking pattern of each of its 4 LEDs, supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, WOL, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8574 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:43 +07:00
/* bus->mdio_lock should be locked when using this function */
static bool vsc8574_is_serdes_init(struct phy_device *phydev)
{
u16 reg;
bool ret;
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS,
MSCC_PHY_PAGE_EXTENDED_GPIO);
reg = phy_base_read(phydev, MSCC_TRAP_ROM_ADDR(1));
if (reg != 0x3eb7) {
ret = false;
goto out;
}
reg = phy_base_read(phydev, MSCC_PATCH_RAM_ADDR(1));
if (reg != 0x4012) {
ret = false;
goto out;
}
reg = phy_base_read(phydev, MSCC_INT_MEM_CNTL);
if (reg != EN_PATCH_RAM_TRAP_ADDR(1)) {
ret = false;
goto out;
}
reg = phy_base_read(phydev, MSCC_DW8051_CNTL_STATUS);
if ((MICRO_NSOFT_RESET | RUN_FROM_INT_ROM | DW8051_CLK_EN |
MICRO_CLK_EN) != (reg & MSCC_DW8051_VLD_MASK)) {
ret = false;
goto out;
}
ret = true;
out:
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
return ret;
}
/* bus->mdio_lock should be locked when using this function */
static int vsc8574_config_pre_init(struct phy_device *phydev)
{
static const struct reg_val pre_init1[] = {
net: phy: mscc: add support for VSC8574 PHY The VSC8574 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports WOL, downshifting and can set the blinking pattern of each of its 4 LEDs, supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, WOL, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8574 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:43 +07:00
{0x0fae, 0x000401bd},
{0x0fac, 0x000f000f},
{0x17a0, 0x00a0f147},
{0x0fe4, 0x00052f54},
{0x1792, 0x0027303d},
{0x07fe, 0x00000704},
{0x0fe0, 0x00060150},
{0x0f82, 0x0012b00a},
{0x0f80, 0x00000d74},
{0x02e0, 0x00000012},
{0x03a2, 0x00050208},
{0x03b2, 0x00009186},
{0x0fb0, 0x000e3700},
{0x1688, 0x00049f81},
{0x0fd2, 0x0000ffff},
{0x168a, 0x00039fa2},
{0x1690, 0x0020640b},
{0x0258, 0x00002220},
{0x025a, 0x00002a20},
{0x025c, 0x00003060},
{0x025e, 0x00003fa0},
{0x03a6, 0x0000e0f0},
{0x0f92, 0x00001489},
{0x16a2, 0x00007000},
{0x16a6, 0x00071448},
{0x16a0, 0x00eeffdd},
{0x0fe8, 0x0091b06c},
{0x0fea, 0x00041600},
{0x16b0, 0x00eeff00},
{0x16b2, 0x00007000},
{0x16b4, 0x00000814},
{0x0f90, 0x00688980},
{0x03a4, 0x0000d8f0},
{0x0fc0, 0x00000400},
{0x07fa, 0x0050100f},
{0x0796, 0x00000003},
{0x07f8, 0x00c3ff98},
{0x0fa4, 0x0018292a},
{0x168c, 0x00d2c46f},
{0x17a2, 0x00000620},
{0x16a4, 0x0013132f},
{0x16a8, 0x00000000},
{0x0ffc, 0x00c0a028},
{0x0fec, 0x00901c09},
{0x0fee, 0x0004a6a1},
{0x0ffe, 0x00b01807},
};
static const struct reg_val pre_init2[] = {
net: phy: mscc: add support for VSC8574 PHY The VSC8574 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports WOL, downshifting and can set the blinking pattern of each of its 4 LEDs, supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, WOL, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8574 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:43 +07:00
{0x0486, 0x0008a518},
{0x0488, 0x006dc696},
{0x048a, 0x00000912},
{0x048e, 0x00000db6},
{0x049c, 0x00596596},
{0x049e, 0x00000514},
{0x04a2, 0x00410280},
{0x04a4, 0x00000000},
{0x04a6, 0x00000000},
{0x04a8, 0x00000000},
{0x04aa, 0x00000000},
{0x04ae, 0x007df7dd},
{0x04b0, 0x006d95d4},
{0x04b2, 0x00492410},
};
struct device *dev = &phydev->mdio.dev;
const struct firmware *fw;
unsigned int i;
u16 crc, reg;
bool serdes_init;
int ret;
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
/* all writes below are broadcasted to all PHYs in the same package */
reg = phy_base_read(phydev, MSCC_PHY_EXT_CNTL_STATUS);
reg |= SMI_BROADCAST_WR_EN;
phy_base_write(phydev, MSCC_PHY_EXT_CNTL_STATUS, reg);
phy_base_write(phydev, MII_VSC85XX_INT_MASK, 0);
/* The below register writes are tweaking analog and electrical
* configuration that were determined through characterization by PHY
* engineers. These don't mean anything more than "these are the best
* values".
*/
phy_base_write(phydev, MSCC_PHY_EXT_PHY_CNTL_2, 0x0040);
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_TEST);
phy_base_write(phydev, MSCC_PHY_TEST_PAGE_20, 0x4320);
phy_base_write(phydev, MSCC_PHY_TEST_PAGE_24, 0x0c00);
phy_base_write(phydev, MSCC_PHY_TEST_PAGE_9, 0x18ca);
phy_base_write(phydev, MSCC_PHY_TEST_PAGE_5, 0x1b20);
reg = phy_base_read(phydev, MSCC_PHY_TEST_PAGE_8);
reg |= 0x8000;
phy_base_write(phydev, MSCC_PHY_TEST_PAGE_8, reg);
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_TR);
for (i = 0; i < ARRAY_SIZE(pre_init1); i++)
vsc8584_csr_write(phydev, pre_init1[i].reg, pre_init1[i].val);
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_EXTENDED_2);
phy_base_write(phydev, MSCC_PHY_CU_PMD_TX_CNTL, 0x028e);
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_TR);
for (i = 0; i < ARRAY_SIZE(pre_init2); i++)
vsc8584_csr_write(phydev, pre_init2[i].reg, pre_init2[i].val);
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_TEST);
reg = phy_base_read(phydev, MSCC_PHY_TEST_PAGE_8);
reg &= ~0x8000;
phy_base_write(phydev, MSCC_PHY_TEST_PAGE_8, reg);
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
/* end of write broadcasting */
reg = phy_base_read(phydev, MSCC_PHY_EXT_CNTL_STATUS);
reg &= ~SMI_BROADCAST_WR_EN;
phy_base_write(phydev, MSCC_PHY_EXT_CNTL_STATUS, reg);
ret = request_firmware(&fw, MSCC_VSC8574_REVB_INT8051_FW, dev);
if (ret) {
dev_err(dev, "failed to load firmware %s, ret: %d\n",
MSCC_VSC8574_REVB_INT8051_FW, ret);
return ret;
}
/* Add one byte to size for the one added by the patch_fw function */
ret = vsc8584_get_fw_crc(phydev,
MSCC_VSC8574_REVB_INT8051_FW_START_ADDR,
fw->size + 1, &crc);
if (ret)
goto out;
if (crc == MSCC_VSC8574_REVB_INT8051_FW_CRC) {
serdes_init = vsc8574_is_serdes_init(phydev);
if (!serdes_init) {
ret = vsc8584_micro_assert_reset(phydev);
if (ret) {
dev_err(dev,
"%s: failed to assert reset of micro\n",
__func__);
goto out;
net: phy: mscc: add support for VSC8574 PHY The VSC8574 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports WOL, downshifting and can set the blinking pattern of each of its 4 LEDs, supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, WOL, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8574 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:43 +07:00
}
}
} else {
dev_dbg(dev, "FW CRC is not the expected one, patching FW\n");
serdes_init = false;
if (vsc8584_patch_fw(phydev, fw))
dev_warn(dev,
"failed to patch FW, expect non-optimal device\n");
}
if (!serdes_init) {
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS,
MSCC_PHY_PAGE_EXTENDED_GPIO);
phy_base_write(phydev, MSCC_TRAP_ROM_ADDR(1), 0x3eb7);
phy_base_write(phydev, MSCC_PATCH_RAM_ADDR(1), 0x4012);
phy_base_write(phydev, MSCC_INT_MEM_CNTL,
EN_PATCH_RAM_TRAP_ADDR(1));
vsc8584_micro_deassert_reset(phydev, false);
/* Add one byte to size for the one added by the patch_fw
* function
*/
ret = vsc8584_get_fw_crc(phydev,
MSCC_VSC8574_REVB_INT8051_FW_START_ADDR,
fw->size + 1, &crc);
if (ret)
goto out;
if (crc != MSCC_VSC8574_REVB_INT8051_FW_CRC)
dev_warn(dev,
"FW CRC after patching is not the expected one, expect non-optimal device\n");
}
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS,
MSCC_PHY_PAGE_EXTENDED_GPIO);
ret = vsc8584_cmd(phydev, PROC_CMD_1588_DEFAULT_INIT |
PROC_CMD_PHY_INIT);
out:
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
release_firmware(fw);
return ret;
}
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
/* bus->mdio_lock should be locked when using this function */
static int vsc8584_config_pre_init(struct phy_device *phydev)
{
static const struct reg_val pre_init1[] = {
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
{0x07fa, 0x0050100f},
{0x1688, 0x00049f81},
{0x0f90, 0x00688980},
{0x03a4, 0x0000d8f0},
{0x0fc0, 0x00000400},
{0x0f82, 0x0012b002},
{0x1686, 0x00000004},
{0x168c, 0x00d2c46f},
{0x17a2, 0x00000620},
{0x16a0, 0x00eeffdd},
{0x16a6, 0x00071448},
{0x16a4, 0x0013132f},
{0x16a8, 0x00000000},
{0x0ffc, 0x00c0a028},
{0x0fe8, 0x0091b06c},
{0x0fea, 0x00041600},
{0x0f80, 0x00fffaff},
{0x0fec, 0x00901809},
{0x0ffe, 0x00b01007},
{0x16b0, 0x00eeff00},
{0x16b2, 0x00007000},
{0x16b4, 0x00000814},
};
static const struct reg_val pre_init2[] = {
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
{0x0486, 0x0008a518},
{0x0488, 0x006dc696},
{0x048a, 0x00000912},
};
const struct firmware *fw;
struct device *dev = &phydev->mdio.dev;
unsigned int i;
u16 crc, reg;
int ret;
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
/* all writes below are broadcasted to all PHYs in the same package */
reg = phy_base_read(phydev, MSCC_PHY_EXT_CNTL_STATUS);
reg |= SMI_BROADCAST_WR_EN;
phy_base_write(phydev, MSCC_PHY_EXT_CNTL_STATUS, reg);
phy_base_write(phydev, MII_VSC85XX_INT_MASK, 0);
reg = phy_base_read(phydev, MSCC_PHY_BYPASS_CONTROL);
reg |= PARALLEL_DET_IGNORE_ADVERTISED;
phy_base_write(phydev, MSCC_PHY_BYPASS_CONTROL, reg);
/* The below register writes are tweaking analog and electrical
* configuration that were determined through characterization by PHY
* engineers. These don't mean anything more than "these are the best
* values".
*/
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_EXTENDED_3);
phy_base_write(phydev, MSCC_PHY_SERDES_TX_CRC_ERR_CNT, 0x2000);
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_TEST);
phy_base_write(phydev, MSCC_PHY_TEST_PAGE_5, 0x1f20);
reg = phy_base_read(phydev, MSCC_PHY_TEST_PAGE_8);
reg |= 0x8000;
phy_base_write(phydev, MSCC_PHY_TEST_PAGE_8, reg);
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_TR);
phy_base_write(phydev, MSCC_PHY_TR_CNTL, TR_WRITE | TR_ADDR(0x2fa4));
reg = phy_base_read(phydev, MSCC_PHY_TR_MSB);
reg &= ~0x007f;
reg |= 0x0019;
phy_base_write(phydev, MSCC_PHY_TR_MSB, reg);
phy_base_write(phydev, MSCC_PHY_TR_CNTL, TR_WRITE | TR_ADDR(0x0fa4));
for (i = 0; i < ARRAY_SIZE(pre_init1); i++)
vsc8584_csr_write(phydev, pre_init1[i].reg, pre_init1[i].val);
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_EXTENDED_2);
phy_base_write(phydev, MSCC_PHY_CU_PMD_TX_CNTL, 0x028e);
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_TR);
for (i = 0; i < ARRAY_SIZE(pre_init2); i++)
vsc8584_csr_write(phydev, pre_init2[i].reg, pre_init2[i].val);
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_TEST);
reg = phy_base_read(phydev, MSCC_PHY_TEST_PAGE_8);
reg &= ~0x8000;
phy_base_write(phydev, MSCC_PHY_TEST_PAGE_8, reg);
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
/* end of write broadcasting */
reg = phy_base_read(phydev, MSCC_PHY_EXT_CNTL_STATUS);
reg &= ~SMI_BROADCAST_WR_EN;
phy_base_write(phydev, MSCC_PHY_EXT_CNTL_STATUS, reg);
ret = request_firmware(&fw, MSCC_VSC8584_REVB_INT8051_FW, dev);
if (ret) {
dev_err(dev, "failed to load firmware %s, ret: %d\n",
MSCC_VSC8584_REVB_INT8051_FW, ret);
return ret;
}
/* Add one byte to size for the one added by the patch_fw function */
ret = vsc8584_get_fw_crc(phydev,
MSCC_VSC8584_REVB_INT8051_FW_START_ADDR,
fw->size + 1, &crc);
if (ret)
goto out;
if (crc != MSCC_VSC8584_REVB_INT8051_FW_CRC) {
dev_dbg(dev, "FW CRC is not the expected one, patching FW\n");
if (vsc8584_patch_fw(phydev, fw))
dev_warn(dev,
"failed to patch FW, expect non-optimal device\n");
}
vsc8584_micro_deassert_reset(phydev, false);
/* Add one byte to size for the one added by the patch_fw function */
ret = vsc8584_get_fw_crc(phydev,
MSCC_VSC8584_REVB_INT8051_FW_START_ADDR,
fw->size + 1, &crc);
if (ret)
goto out;
if (crc != MSCC_VSC8584_REVB_INT8051_FW_CRC)
dev_warn(dev,
"FW CRC after patching is not the expected one, expect non-optimal device\n");
ret = vsc8584_micro_assert_reset(phydev);
if (ret)
goto out;
vsc8584_micro_deassert_reset(phydev, true);
out:
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
release_firmware(fw);
return ret;
}
#if IS_ENABLED(CONFIG_MACSEC)
static u32 vsc8584_macsec_phy_read(struct phy_device *phydev,
enum macsec_bank bank, u32 reg)
{
u32 val, val_l = 0, val_h = 0;
unsigned long deadline;
int rc;
rc = phy_select_page(phydev, MSCC_PHY_PAGE_MACSEC);
if (rc < 0)
goto failed;
__phy_write(phydev, MSCC_EXT_PAGE_MACSEC_20,
MSCC_PHY_MACSEC_20_TARGET(bank >> 2));
if (bank >> 2 == 0x1)
/* non-MACsec access */
bank &= 0x3;
else
bank = 0;
__phy_write(phydev, MSCC_EXT_PAGE_MACSEC_19,
MSCC_PHY_MACSEC_19_CMD | MSCC_PHY_MACSEC_19_READ |
MSCC_PHY_MACSEC_19_REG_ADDR(reg) |
MSCC_PHY_MACSEC_19_TARGET(bank));
deadline = jiffies + msecs_to_jiffies(PROC_CMD_NCOMPLETED_TIMEOUT_MS);
do {
val = __phy_read(phydev, MSCC_EXT_PAGE_MACSEC_19);
} while (time_before(jiffies, deadline) && !(val & MSCC_PHY_MACSEC_19_CMD));
val_l = __phy_read(phydev, MSCC_EXT_PAGE_MACSEC_17);
val_h = __phy_read(phydev, MSCC_EXT_PAGE_MACSEC_18);
failed:
phy_restore_page(phydev, rc, rc);
return (val_h << 16) | val_l;
}
static void vsc8584_macsec_phy_write(struct phy_device *phydev,
enum macsec_bank bank, u32 reg, u32 val)
{
unsigned long deadline;
int rc;
rc = phy_select_page(phydev, MSCC_PHY_PAGE_MACSEC);
if (rc < 0)
goto failed;
__phy_write(phydev, MSCC_EXT_PAGE_MACSEC_20,
MSCC_PHY_MACSEC_20_TARGET(bank >> 2));
if ((bank >> 2 == 0x1) || (bank >> 2 == 0x3))
bank &= 0x3;
else
/* MACsec access */
bank = 0;
__phy_write(phydev, MSCC_EXT_PAGE_MACSEC_17, (u16)val);
__phy_write(phydev, MSCC_EXT_PAGE_MACSEC_18, (u16)(val >> 16));
__phy_write(phydev, MSCC_EXT_PAGE_MACSEC_19,
MSCC_PHY_MACSEC_19_CMD | MSCC_PHY_MACSEC_19_REG_ADDR(reg) |
MSCC_PHY_MACSEC_19_TARGET(bank));
deadline = jiffies + msecs_to_jiffies(PROC_CMD_NCOMPLETED_TIMEOUT_MS);
do {
val = __phy_read(phydev, MSCC_EXT_PAGE_MACSEC_19);
} while (time_before(jiffies, deadline) && !(val & MSCC_PHY_MACSEC_19_CMD));
failed:
phy_restore_page(phydev, rc, rc);
}
static void vsc8584_macsec_classification(struct phy_device *phydev,
enum macsec_bank bank)
{
/* enable VLAN tag parsing */
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_SAM_CP_TAG,
MSCC_MS_SAM_CP_TAG_PARSE_STAG |
MSCC_MS_SAM_CP_TAG_PARSE_QTAG |
MSCC_MS_SAM_CP_TAG_PARSE_QINQ);
}
static void vsc8584_macsec_flow_default_action(struct phy_device *phydev,
enum macsec_bank bank,
bool block)
{
u32 port = (bank == MACSEC_INGR) ?
MSCC_MS_PORT_UNCONTROLLED : MSCC_MS_PORT_COMMON;
u32 action = MSCC_MS_FLOW_BYPASS;
if (block)
action = MSCC_MS_FLOW_DROP;
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_SAM_NM_FLOW_NCP,
/* MACsec untagged */
MSCC_MS_SAM_NM_FLOW_NCP_UNTAGGED_FLOW_TYPE(action) |
MSCC_MS_SAM_NM_FLOW_NCP_UNTAGGED_DROP_ACTION(MSCC_MS_ACTION_DROP) |
MSCC_MS_SAM_NM_FLOW_NCP_UNTAGGED_DEST_PORT(port) |
/* MACsec tagged */
MSCC_MS_SAM_NM_FLOW_NCP_TAGGED_FLOW_TYPE(action) |
MSCC_MS_SAM_NM_FLOW_NCP_TAGGED_DROP_ACTION(MSCC_MS_ACTION_DROP) |
MSCC_MS_SAM_NM_FLOW_NCP_TAGGED_DEST_PORT(port) |
/* Bad tag */
MSCC_MS_SAM_NM_FLOW_NCP_BADTAG_FLOW_TYPE(action) |
MSCC_MS_SAM_NM_FLOW_NCP_BADTAG_DROP_ACTION(MSCC_MS_ACTION_DROP) |
MSCC_MS_SAM_NM_FLOW_NCP_BADTAG_DEST_PORT(port) |
/* Kay tag */
MSCC_MS_SAM_NM_FLOW_NCP_KAY_FLOW_TYPE(action) |
MSCC_MS_SAM_NM_FLOW_NCP_KAY_DROP_ACTION(MSCC_MS_ACTION_DROP) |
MSCC_MS_SAM_NM_FLOW_NCP_KAY_DEST_PORT(port));
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_SAM_NM_FLOW_CP,
/* MACsec untagged */
MSCC_MS_SAM_NM_FLOW_NCP_UNTAGGED_FLOW_TYPE(action) |
MSCC_MS_SAM_NM_FLOW_CP_UNTAGGED_DROP_ACTION(MSCC_MS_ACTION_DROP) |
MSCC_MS_SAM_NM_FLOW_CP_UNTAGGED_DEST_PORT(port) |
/* MACsec tagged */
MSCC_MS_SAM_NM_FLOW_NCP_TAGGED_FLOW_TYPE(action) |
MSCC_MS_SAM_NM_FLOW_CP_TAGGED_DROP_ACTION(MSCC_MS_ACTION_DROP) |
MSCC_MS_SAM_NM_FLOW_CP_TAGGED_DEST_PORT(port) |
/* Bad tag */
MSCC_MS_SAM_NM_FLOW_NCP_BADTAG_FLOW_TYPE(action) |
MSCC_MS_SAM_NM_FLOW_CP_BADTAG_DROP_ACTION(MSCC_MS_ACTION_DROP) |
MSCC_MS_SAM_NM_FLOW_CP_BADTAG_DEST_PORT(port) |
/* Kay tag */
MSCC_MS_SAM_NM_FLOW_NCP_KAY_FLOW_TYPE(action) |
MSCC_MS_SAM_NM_FLOW_CP_KAY_DROP_ACTION(MSCC_MS_ACTION_DROP) |
MSCC_MS_SAM_NM_FLOW_CP_KAY_DEST_PORT(port));
}
static void vsc8584_macsec_integrity_checks(struct phy_device *phydev,
enum macsec_bank bank)
{
u32 val;
if (bank != MACSEC_INGR)
return;
/* Set default rules to pass unmatched frames */
val = vsc8584_macsec_phy_read(phydev, bank,
MSCC_MS_PARAMS2_IG_CC_CONTROL);
val |= MSCC_MS_PARAMS2_IG_CC_CONTROL_NON_MATCH_CTRL_ACT |
MSCC_MS_PARAMS2_IG_CC_CONTROL_NON_MATCH_ACT;
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_PARAMS2_IG_CC_CONTROL,
val);
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_PARAMS2_IG_CP_TAG,
MSCC_MS_PARAMS2_IG_CP_TAG_PARSE_STAG |
MSCC_MS_PARAMS2_IG_CP_TAG_PARSE_QTAG |
MSCC_MS_PARAMS2_IG_CP_TAG_PARSE_QINQ);
}
static void vsc8584_macsec_block_init(struct phy_device *phydev,
enum macsec_bank bank)
{
u32 val;
int i;
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_ENA_CFG,
MSCC_MS_ENA_CFG_SW_RST |
MSCC_MS_ENA_CFG_MACSEC_BYPASS_ENA);
/* Set the MACsec block out of s/w reset and enable clocks */
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_ENA_CFG,
MSCC_MS_ENA_CFG_CLK_ENA);
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_STATUS_CONTEXT_CTRL,
bank == MACSEC_INGR ? 0xe5880214 : 0xe5880218);
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_MISC_CONTROL,
MSCC_MS_MISC_CONTROL_MC_LATENCY_FIX(bank == MACSEC_INGR ? 57 : 40) |
MSCC_MS_MISC_CONTROL_XFORM_REC_SIZE(bank == MACSEC_INGR ? 1 : 2));
/* Clear the counters */
val = vsc8584_macsec_phy_read(phydev, bank, MSCC_MS_COUNT_CONTROL);
val |= MSCC_MS_COUNT_CONTROL_AUTO_CNTR_RESET;
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_COUNT_CONTROL, val);
/* Enable octet increment mode */
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_PP_CTRL,
MSCC_MS_PP_CTRL_MACSEC_OCTET_INCR_MODE);
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_BLOCK_CTX_UPDATE, 0x3);
val = vsc8584_macsec_phy_read(phydev, bank, MSCC_MS_COUNT_CONTROL);
val |= MSCC_MS_COUNT_CONTROL_RESET_ALL;
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_COUNT_CONTROL, val);
/* Set the MTU */
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_NON_VLAN_MTU_CHECK,
MSCC_MS_NON_VLAN_MTU_CHECK_NV_MTU_COMPARE(32761) |
MSCC_MS_NON_VLAN_MTU_CHECK_NV_MTU_COMP_DROP);
for (i = 0; i < 8; i++)
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_VLAN_MTU_CHECK(i),
MSCC_MS_VLAN_MTU_CHECK_MTU_COMPARE(32761) |
MSCC_MS_VLAN_MTU_CHECK_MTU_COMP_DROP);
if (bank == MACSEC_EGR) {
val = vsc8584_macsec_phy_read(phydev, bank, MSCC_MS_INTR_CTRL_STATUS);
val &= ~MSCC_MS_INTR_CTRL_STATUS_INTR_ENABLE_M;
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_INTR_CTRL_STATUS, val);
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_FC_CFG,
MSCC_MS_FC_CFG_FCBUF_ENA |
MSCC_MS_FC_CFG_LOW_THRESH(0x1) |
MSCC_MS_FC_CFG_HIGH_THRESH(0x4) |
MSCC_MS_FC_CFG_LOW_BYTES_VAL(0x4) |
MSCC_MS_FC_CFG_HIGH_BYTES_VAL(0x6));
}
vsc8584_macsec_classification(phydev, bank);
vsc8584_macsec_flow_default_action(phydev, bank, false);
vsc8584_macsec_integrity_checks(phydev, bank);
/* Enable the MACsec block */
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_ENA_CFG,
MSCC_MS_ENA_CFG_CLK_ENA |
MSCC_MS_ENA_CFG_MACSEC_ENA |
MSCC_MS_ENA_CFG_MACSEC_SPEED_MODE(0x5));
}
static void vsc8584_macsec_mac_init(struct phy_device *phydev,
enum macsec_bank bank)
{
u32 val;
int i;
/* Clear host & line stats */
for (i = 0; i < 36; i++)
vsc8584_macsec_phy_write(phydev, bank, 0x1c + i, 0);
val = vsc8584_macsec_phy_read(phydev, bank,
MSCC_MAC_PAUSE_CFG_TX_FRAME_CTRL);
val &= ~MSCC_MAC_PAUSE_CFG_TX_FRAME_CTRL_PAUSE_MODE_M;
val |= MSCC_MAC_PAUSE_CFG_TX_FRAME_CTRL_PAUSE_MODE(2) |
MSCC_MAC_PAUSE_CFG_TX_FRAME_CTRL_PAUSE_VALUE(0xffff);
vsc8584_macsec_phy_write(phydev, bank,
MSCC_MAC_PAUSE_CFG_TX_FRAME_CTRL, val);
val = vsc8584_macsec_phy_read(phydev, bank,
MSCC_MAC_PAUSE_CFG_TX_FRAME_CTRL_2);
val |= 0xffff;
vsc8584_macsec_phy_write(phydev, bank,
MSCC_MAC_PAUSE_CFG_TX_FRAME_CTRL_2, val);
val = vsc8584_macsec_phy_read(phydev, bank,
MSCC_MAC_PAUSE_CFG_RX_FRAME_CTRL);
if (bank == HOST_MAC)
val |= MSCC_MAC_PAUSE_CFG_RX_FRAME_CTRL_PAUSE_TIMER_ENA |
MSCC_MAC_PAUSE_CFG_RX_FRAME_CTRL_PAUSE_FRAME_DROP_ENA;
else
val |= MSCC_MAC_PAUSE_CFG_RX_FRAME_CTRL_PAUSE_REACT_ENA |
MSCC_MAC_PAUSE_CFG_RX_FRAME_CTRL_PAUSE_FRAME_DROP_ENA |
MSCC_MAC_PAUSE_CFG_RX_FRAME_CTRL_PAUSE_MODE |
MSCC_MAC_PAUSE_CFG_RX_FRAME_CTRL_EARLY_PAUSE_DETECT_ENA;
vsc8584_macsec_phy_write(phydev, bank,
MSCC_MAC_PAUSE_CFG_RX_FRAME_CTRL, val);
vsc8584_macsec_phy_write(phydev, bank, MSCC_MAC_CFG_PKTINF_CFG,
MSCC_MAC_CFG_PKTINF_CFG_STRIP_FCS_ENA |
MSCC_MAC_CFG_PKTINF_CFG_INSERT_FCS_ENA |
MSCC_MAC_CFG_PKTINF_CFG_LPI_RELAY_ENA |
MSCC_MAC_CFG_PKTINF_CFG_STRIP_PREAMBLE_ENA |
MSCC_MAC_CFG_PKTINF_CFG_INSERT_PREAMBLE_ENA |
(bank == HOST_MAC ?
MSCC_MAC_CFG_PKTINF_CFG_ENABLE_TX_PADDING : 0));
val = vsc8584_macsec_phy_read(phydev, bank, MSCC_MAC_CFG_MODE_CFG);
val &= ~MSCC_MAC_CFG_MODE_CFG_DISABLE_DIC;
vsc8584_macsec_phy_write(phydev, bank, MSCC_MAC_CFG_MODE_CFG, val);
val = vsc8584_macsec_phy_read(phydev, bank, MSCC_MAC_CFG_MAXLEN_CFG);
val &= ~MSCC_MAC_CFG_MAXLEN_CFG_MAX_LEN_M;
val |= MSCC_MAC_CFG_MAXLEN_CFG_MAX_LEN(10240);
vsc8584_macsec_phy_write(phydev, bank, MSCC_MAC_CFG_MAXLEN_CFG, val);
vsc8584_macsec_phy_write(phydev, bank, MSCC_MAC_CFG_ADV_CHK_CFG,
MSCC_MAC_CFG_ADV_CHK_CFG_SFD_CHK_ENA |
MSCC_MAC_CFG_ADV_CHK_CFG_PRM_CHK_ENA |
MSCC_MAC_CFG_ADV_CHK_CFG_OOR_ERR_ENA |
MSCC_MAC_CFG_ADV_CHK_CFG_INR_ERR_ENA);
val = vsc8584_macsec_phy_read(phydev, bank, MSCC_MAC_CFG_LFS_CFG);
val &= ~MSCC_MAC_CFG_LFS_CFG_LFS_MODE_ENA;
vsc8584_macsec_phy_write(phydev, bank, MSCC_MAC_CFG_LFS_CFG, val);
vsc8584_macsec_phy_write(phydev, bank, MSCC_MAC_CFG_ENA_CFG,
MSCC_MAC_CFG_ENA_CFG_RX_CLK_ENA |
MSCC_MAC_CFG_ENA_CFG_TX_CLK_ENA |
MSCC_MAC_CFG_ENA_CFG_RX_ENA |
MSCC_MAC_CFG_ENA_CFG_TX_ENA);
}
/* Must be called with mdio_lock taken */
static int vsc8584_macsec_init(struct phy_device *phydev)
{
u32 val;
vsc8584_macsec_block_init(phydev, MACSEC_INGR);
vsc8584_macsec_block_init(phydev, MACSEC_EGR);
vsc8584_macsec_mac_init(phydev, HOST_MAC);
vsc8584_macsec_mac_init(phydev, LINE_MAC);
vsc8584_macsec_phy_write(phydev, FC_BUFFER,
MSCC_FCBUF_FC_READ_THRESH_CFG,
MSCC_FCBUF_FC_READ_THRESH_CFG_TX_THRESH(4) |
MSCC_FCBUF_FC_READ_THRESH_CFG_RX_THRESH(5));
val = vsc8584_macsec_phy_read(phydev, FC_BUFFER, MSCC_FCBUF_MODE_CFG);
val |= MSCC_FCBUF_MODE_CFG_PAUSE_GEN_ENA |
MSCC_FCBUF_MODE_CFG_RX_PPM_RATE_ADAPT_ENA |
MSCC_FCBUF_MODE_CFG_TX_PPM_RATE_ADAPT_ENA;
vsc8584_macsec_phy_write(phydev, FC_BUFFER, MSCC_FCBUF_MODE_CFG, val);
vsc8584_macsec_phy_write(phydev, FC_BUFFER, MSCC_FCBUF_PPM_RATE_ADAPT_THRESH_CFG,
MSCC_FCBUF_PPM_RATE_ADAPT_THRESH_CFG_TX_THRESH(8) |
MSCC_FCBUF_PPM_RATE_ADAPT_THRESH_CFG_TX_OFFSET(9));
val = vsc8584_macsec_phy_read(phydev, FC_BUFFER,
MSCC_FCBUF_TX_DATA_QUEUE_CFG);
val &= ~(MSCC_FCBUF_TX_DATA_QUEUE_CFG_START_M |
MSCC_FCBUF_TX_DATA_QUEUE_CFG_END_M);
val |= MSCC_FCBUF_TX_DATA_QUEUE_CFG_START(0) |
MSCC_FCBUF_TX_DATA_QUEUE_CFG_END(5119);
vsc8584_macsec_phy_write(phydev, FC_BUFFER,
MSCC_FCBUF_TX_DATA_QUEUE_CFG, val);
val = vsc8584_macsec_phy_read(phydev, FC_BUFFER, MSCC_FCBUF_ENA_CFG);
val |= MSCC_FCBUF_ENA_CFG_TX_ENA | MSCC_FCBUF_ENA_CFG_RX_ENA;
vsc8584_macsec_phy_write(phydev, FC_BUFFER, MSCC_FCBUF_ENA_CFG, val);
val = vsc8584_macsec_phy_read(phydev, IP_1588,
MSCC_PROC_0_IP_1588_TOP_CFG_STAT_MODE_CTL);
val &= ~MSCC_PROC_0_IP_1588_TOP_CFG_STAT_MODE_CTL_PROTOCOL_MODE_M;
val |= MSCC_PROC_0_IP_1588_TOP_CFG_STAT_MODE_CTL_PROTOCOL_MODE(4);
vsc8584_macsec_phy_write(phydev, IP_1588,
MSCC_PROC_0_IP_1588_TOP_CFG_STAT_MODE_CTL, val);
return 0;
}
static void vsc8584_macsec_flow(struct phy_device *phydev,
struct macsec_flow *flow)
{
struct vsc8531_private *priv = phydev->priv;
enum macsec_bank bank = flow->bank;
u32 val, match = 0, mask = 0, action = 0, idx = flow->index;
if (flow->match.tagged)
match |= MSCC_MS_SAM_MISC_MATCH_TAGGED;
if (flow->match.untagged)
match |= MSCC_MS_SAM_MISC_MATCH_UNTAGGED;
if (bank == MACSEC_INGR && flow->assoc_num >= 0) {
match |= MSCC_MS_SAM_MISC_MATCH_AN(flow->assoc_num);
mask |= MSCC_MS_SAM_MASK_AN_MASK(0x3);
}
if (bank == MACSEC_INGR && flow->match.sci && flow->rx_sa->sc->sci) {
match |= MSCC_MS_SAM_MISC_MATCH_TCI(BIT(3));
mask |= MSCC_MS_SAM_MASK_TCI_MASK(BIT(3)) |
MSCC_MS_SAM_MASK_SCI_MASK;
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_SAM_MATCH_SCI_LO(idx),
lower_32_bits(flow->rx_sa->sc->sci));
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_SAM_MATCH_SCI_HI(idx),
upper_32_bits(flow->rx_sa->sc->sci));
}
if (flow->match.etype) {
mask |= MSCC_MS_SAM_MASK_MAC_ETYPE_MASK;
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_SAM_MAC_SA_MATCH_HI(idx),
MSCC_MS_SAM_MAC_SA_MATCH_HI_ETYPE(htons(flow->etype)));
}
match |= MSCC_MS_SAM_MISC_MATCH_PRIORITY(flow->priority);
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_SAM_MISC_MATCH(idx), match);
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_SAM_MASK(idx), mask);
/* Action for matching packets */
if (flow->action.drop)
action = MSCC_MS_FLOW_DROP;
else if (flow->action.bypass || flow->port == MSCC_MS_PORT_UNCONTROLLED)
action = MSCC_MS_FLOW_BYPASS;
else
action = (bank == MACSEC_INGR) ?
MSCC_MS_FLOW_INGRESS : MSCC_MS_FLOW_EGRESS;
val = MSCC_MS_SAM_FLOW_CTRL_FLOW_TYPE(action) |
MSCC_MS_SAM_FLOW_CTRL_DROP_ACTION(MSCC_MS_ACTION_DROP) |
MSCC_MS_SAM_FLOW_CTRL_DEST_PORT(flow->port);
if (action == MSCC_MS_FLOW_BYPASS)
goto write_ctrl;
if (bank == MACSEC_INGR) {
if (priv->secy->replay_protect)
val |= MSCC_MS_SAM_FLOW_CTRL_REPLAY_PROTECT;
if (priv->secy->validate_frames == MACSEC_VALIDATE_STRICT)
val |= MSCC_MS_SAM_FLOW_CTRL_VALIDATE_FRAMES(MSCC_MS_VALIDATE_STRICT);
else if (priv->secy->validate_frames == MACSEC_VALIDATE_CHECK)
val |= MSCC_MS_SAM_FLOW_CTRL_VALIDATE_FRAMES(MSCC_MS_VALIDATE_CHECK);
} else if (bank == MACSEC_EGR) {
if (priv->secy->protect_frames)
val |= MSCC_MS_SAM_FLOW_CTRL_PROTECT_FRAME;
if (priv->secy->tx_sc.encrypt)
val |= MSCC_MS_SAM_FLOW_CTRL_CONF_PROTECT;
if (priv->secy->tx_sc.send_sci)
val |= MSCC_MS_SAM_FLOW_CTRL_INCLUDE_SCI;
}
write_ctrl:
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_SAM_FLOW_CTRL(idx), val);
}
static struct macsec_flow *vsc8584_macsec_find_flow(struct macsec_context *ctx,
enum macsec_bank bank)
{
struct vsc8531_private *priv = ctx->phydev->priv;
struct macsec_flow *pos, *tmp;
list_for_each_entry_safe(pos, tmp, &priv->macsec_flows, list)
if (pos->assoc_num == ctx->sa.assoc_num && pos->bank == bank)
return pos;
return ERR_PTR(-ENOENT);
}
static void vsc8584_macsec_flow_enable(struct phy_device *phydev,
struct macsec_flow *flow)
{
enum macsec_bank bank = flow->bank;
u32 val, idx = flow->index;
if ((flow->bank == MACSEC_INGR && flow->rx_sa && !flow->rx_sa->active) ||
(flow->bank == MACSEC_EGR && flow->tx_sa && !flow->tx_sa->active))
return;
/* Enable */
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_SAM_ENTRY_SET1, BIT(idx));
/* Set in-use */
val = vsc8584_macsec_phy_read(phydev, bank, MSCC_MS_SAM_FLOW_CTRL(idx));
val |= MSCC_MS_SAM_FLOW_CTRL_SA_IN_USE;
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_SAM_FLOW_CTRL(idx), val);
}
static void vsc8584_macsec_flow_disable(struct phy_device *phydev,
struct macsec_flow *flow)
{
enum macsec_bank bank = flow->bank;
u32 val, idx = flow->index;
/* Disable */
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_SAM_ENTRY_CLEAR1, BIT(idx));
/* Clear in-use */
val = vsc8584_macsec_phy_read(phydev, bank, MSCC_MS_SAM_FLOW_CTRL(idx));
val &= ~MSCC_MS_SAM_FLOW_CTRL_SA_IN_USE;
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_SAM_FLOW_CTRL(idx), val);
}
static u32 vsc8584_macsec_flow_context_id(struct macsec_flow *flow)
{
if (flow->bank == MACSEC_INGR)
return flow->index + MSCC_MS_MAX_FLOWS;
return flow->index;
}
/* Derive the AES key to get a key for the hash autentication */
static int vsc8584_macsec_derive_key(const u8 key[MACSEC_KEYID_LEN],
u16 key_len, u8 hkey[16])
{
struct crypto_skcipher *tfm = crypto_alloc_skcipher("ecb(aes)", 0, 0);
struct skcipher_request *req = NULL;
struct scatterlist src, dst;
DECLARE_CRYPTO_WAIT(wait);
u32 input[4] = {0};
int ret;
if (IS_ERR(tfm))
return PTR_ERR(tfm);
req = skcipher_request_alloc(tfm, GFP_KERNEL);
if (!req) {
ret = -ENOMEM;
goto out;
}
skcipher_request_set_callback(req, CRYPTO_TFM_REQ_MAY_BACKLOG |
CRYPTO_TFM_REQ_MAY_SLEEP, crypto_req_done,
&wait);
ret = crypto_skcipher_setkey(tfm, key, key_len);
if (ret < 0)
goto out;
sg_init_one(&src, input, 16);
sg_init_one(&dst, hkey, 16);
skcipher_request_set_crypt(req, &src, &dst, 16, NULL);
ret = crypto_wait_req(crypto_skcipher_encrypt(req), &wait);
out:
skcipher_request_free(req);
crypto_free_skcipher(tfm);
return ret;
}
static int vsc8584_macsec_transformation(struct phy_device *phydev,
struct macsec_flow *flow)
{
struct vsc8531_private *priv = phydev->priv;
enum macsec_bank bank = flow->bank;
int i, ret, index = flow->index;
u32 rec = 0, control = 0;
u8 hkey[16];
sci_t sci;
ret = vsc8584_macsec_derive_key(flow->key, priv->secy->key_len, hkey);
if (ret)
return ret;
switch (priv->secy->key_len) {
case 16:
control |= CONTROL_CRYPTO_ALG(CTRYPTO_ALG_AES_CTR_128);
break;
case 32:
control |= CONTROL_CRYPTO_ALG(CTRYPTO_ALG_AES_CTR_256);
break;
default:
return -EINVAL;
}
control |= (bank == MACSEC_EGR) ?
(CONTROL_TYPE_EGRESS | CONTROL_AN(priv->secy->tx_sc.encoding_sa)) :
(CONTROL_TYPE_INGRESS | CONTROL_SEQ_MASK);
control |= CONTROL_UPDATE_SEQ | CONTROL_ENCRYPT_AUTH | CONTROL_KEY_IN_CTX |
CONTROL_IV0 | CONTROL_IV1 | CONTROL_IV_IN_SEQ |
CONTROL_DIGEST_TYPE(0x2) | CONTROL_SEQ_TYPE(0x1) |
CONTROL_AUTH_ALG(AUTH_ALG_AES_GHAS) | CONTROL_CONTEXT_ID;
/* Set the control word */
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_XFORM_REC(index, rec++),
control);
/* Set the context ID. Must be unique. */
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_XFORM_REC(index, rec++),
vsc8584_macsec_flow_context_id(flow));
/* Set the encryption/decryption key */
for (i = 0; i < priv->secy->key_len / sizeof(u32); i++)
vsc8584_macsec_phy_write(phydev, bank,
MSCC_MS_XFORM_REC(index, rec++),
((u32 *)flow->key)[i]);
/* Set the authentication key */
for (i = 0; i < 4; i++)
vsc8584_macsec_phy_write(phydev, bank,
MSCC_MS_XFORM_REC(index, rec++),
((u32 *)hkey)[i]);
/* Initial sequence number */
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_XFORM_REC(index, rec++),
bank == MACSEC_INGR ?
flow->rx_sa->next_pn : flow->tx_sa->next_pn);
if (bank == MACSEC_INGR)
/* Set the mask (replay window size) */
vsc8584_macsec_phy_write(phydev, bank,
MSCC_MS_XFORM_REC(index, rec++),
priv->secy->replay_window);
/* Set the input vectors */
sci = bank == MACSEC_INGR ? flow->rx_sa->sc->sci : priv->secy->sci;
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_XFORM_REC(index, rec++),
lower_32_bits(sci));
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_XFORM_REC(index, rec++),
upper_32_bits(sci));
while (rec < 20)
vsc8584_macsec_phy_write(phydev, bank, MSCC_MS_XFORM_REC(index, rec++),
0);
flow->has_transformation = true;
return 0;
}
static struct macsec_flow *vsc8584_macsec_alloc_flow(struct vsc8531_private *priv,
enum macsec_bank bank)
{
unsigned long *bitmap = bank == MACSEC_INGR ?
&priv->ingr_flows : &priv->egr_flows;
struct macsec_flow *flow;
int index;
index = find_first_zero_bit(bitmap, MSCC_MS_MAX_FLOWS);
if (index == MSCC_MS_MAX_FLOWS)
return ERR_PTR(-ENOMEM);
flow = kzalloc(sizeof(*flow), GFP_KERNEL);
if (!flow)
return ERR_PTR(-ENOMEM);
set_bit(index, bitmap);
flow->index = index;
flow->bank = bank;
flow->priority = 8;
flow->assoc_num = -1;
list_add_tail(&flow->list, &priv->macsec_flows);
return flow;
}
static void vsc8584_macsec_free_flow(struct vsc8531_private *priv,
struct macsec_flow *flow)
{
unsigned long *bitmap = flow->bank == MACSEC_INGR ?
&priv->ingr_flows : &priv->egr_flows;
list_del(&flow->list);
clear_bit(flow->index, bitmap);
kfree(flow);
}
static int vsc8584_macsec_add_flow(struct phy_device *phydev,
struct macsec_flow *flow, bool update)
{
int ret;
flow->port = MSCC_MS_PORT_CONTROLLED;
vsc8584_macsec_flow(phydev, flow);
if (update)
return 0;
ret = vsc8584_macsec_transformation(phydev, flow);
if (ret) {
vsc8584_macsec_free_flow(phydev->priv, flow);
return ret;
}
return 0;
}
static int vsc8584_macsec_default_flows(struct phy_device *phydev)
{
struct macsec_flow *flow;
/* Add a rule to let the MKA traffic go through, ingress */
flow = vsc8584_macsec_alloc_flow(phydev->priv, MACSEC_INGR);
if (IS_ERR(flow))
return PTR_ERR(flow);
flow->priority = 15;
flow->port = MSCC_MS_PORT_UNCONTROLLED;
flow->match.tagged = 1;
flow->match.untagged = 1;
flow->match.etype = 1;
flow->etype = ETH_P_PAE;
flow->action.bypass = 1;
vsc8584_macsec_flow(phydev, flow);
vsc8584_macsec_flow_enable(phydev, flow);
/* Add a rule to let the MKA traffic go through, egress */
flow = vsc8584_macsec_alloc_flow(phydev->priv, MACSEC_EGR);
if (IS_ERR(flow))
return PTR_ERR(flow);
flow->priority = 15;
flow->port = MSCC_MS_PORT_COMMON;
flow->match.untagged = 1;
flow->match.etype = 1;
flow->etype = ETH_P_PAE;
flow->action.bypass = 1;
vsc8584_macsec_flow(phydev, flow);
vsc8584_macsec_flow_enable(phydev, flow);
return 0;
}
static void vsc8584_macsec_del_flow(struct phy_device *phydev,
struct macsec_flow *flow)
{
vsc8584_macsec_flow_disable(phydev, flow);
vsc8584_macsec_free_flow(phydev->priv, flow);
}
static int __vsc8584_macsec_add_rxsa(struct macsec_context *ctx,
struct macsec_flow *flow, bool update)
{
struct phy_device *phydev = ctx->phydev;
struct vsc8531_private *priv = phydev->priv;
if (!flow) {
flow = vsc8584_macsec_alloc_flow(priv, MACSEC_INGR);
if (IS_ERR(flow))
return PTR_ERR(flow);
memcpy(flow->key, ctx->sa.key, priv->secy->key_len);
}
flow->assoc_num = ctx->sa.assoc_num;
flow->rx_sa = ctx->sa.rx_sa;
/* Always match tagged packets on ingress */
flow->match.tagged = 1;
flow->match.sci = 1;
if (priv->secy->validate_frames != MACSEC_VALIDATE_DISABLED)
flow->match.untagged = 1;
return vsc8584_macsec_add_flow(phydev, flow, update);
}
static int __vsc8584_macsec_add_txsa(struct macsec_context *ctx,
struct macsec_flow *flow, bool update)
{
struct phy_device *phydev = ctx->phydev;
struct vsc8531_private *priv = phydev->priv;
if (!flow) {
flow = vsc8584_macsec_alloc_flow(priv, MACSEC_EGR);
if (IS_ERR(flow))
return PTR_ERR(flow);
memcpy(flow->key, ctx->sa.key, priv->secy->key_len);
}
flow->assoc_num = ctx->sa.assoc_num;
flow->tx_sa = ctx->sa.tx_sa;
/* Always match untagged packets on egress */
flow->match.untagged = 1;
return vsc8584_macsec_add_flow(phydev, flow, update);
}
static int vsc8584_macsec_dev_open(struct macsec_context *ctx)
{
struct vsc8531_private *priv = ctx->phydev->priv;
struct macsec_flow *flow, *tmp;
/* No operation to perform before the commit step */
if (ctx->prepare)
return 0;
list_for_each_entry_safe(flow, tmp, &priv->macsec_flows, list)
vsc8584_macsec_flow_enable(ctx->phydev, flow);
return 0;
}
static int vsc8584_macsec_dev_stop(struct macsec_context *ctx)
{
struct vsc8531_private *priv = ctx->phydev->priv;
struct macsec_flow *flow, *tmp;
/* No operation to perform before the commit step */
if (ctx->prepare)
return 0;
list_for_each_entry_safe(flow, tmp, &priv->macsec_flows, list)
vsc8584_macsec_flow_disable(ctx->phydev, flow);
return 0;
}
static int vsc8584_macsec_add_secy(struct macsec_context *ctx)
{
struct vsc8531_private *priv = ctx->phydev->priv;
struct macsec_secy *secy = ctx->secy;
if (ctx->prepare) {
if (priv->secy)
return -EEXIST;
return 0;
}
priv->secy = secy;
vsc8584_macsec_flow_default_action(ctx->phydev, MACSEC_EGR,
secy->validate_frames != MACSEC_VALIDATE_DISABLED);
vsc8584_macsec_flow_default_action(ctx->phydev, MACSEC_INGR,
secy->validate_frames != MACSEC_VALIDATE_DISABLED);
return vsc8584_macsec_default_flows(ctx->phydev);
}
static int vsc8584_macsec_del_secy(struct macsec_context *ctx)
{
struct vsc8531_private *priv = ctx->phydev->priv;
struct macsec_flow *flow, *tmp;
/* No operation to perform before the commit step */
if (ctx->prepare)
return 0;
list_for_each_entry_safe(flow, tmp, &priv->macsec_flows, list)
vsc8584_macsec_del_flow(ctx->phydev, flow);
vsc8584_macsec_flow_default_action(ctx->phydev, MACSEC_EGR, false);
vsc8584_macsec_flow_default_action(ctx->phydev, MACSEC_INGR, false);
priv->secy = NULL;
return 0;
}
static int vsc8584_macsec_upd_secy(struct macsec_context *ctx)
{
/* No operation to perform before the commit step */
if (ctx->prepare)
return 0;
vsc8584_macsec_del_secy(ctx);
return vsc8584_macsec_add_secy(ctx);
}
static int vsc8584_macsec_add_rxsc(struct macsec_context *ctx)
{
/* Nothing to do */
return 0;
}
static int vsc8584_macsec_upd_rxsc(struct macsec_context *ctx)
{
return -EOPNOTSUPP;
}
static int vsc8584_macsec_del_rxsc(struct macsec_context *ctx)
{
struct vsc8531_private *priv = ctx->phydev->priv;
struct macsec_flow *flow, *tmp;
/* No operation to perform before the commit step */
if (ctx->prepare)
return 0;
list_for_each_entry_safe(flow, tmp, &priv->macsec_flows, list) {
if (flow->bank == MACSEC_INGR && flow->rx_sa &&
flow->rx_sa->sc->sci == ctx->rx_sc->sci)
vsc8584_macsec_del_flow(ctx->phydev, flow);
}
return 0;
}
static int vsc8584_macsec_add_rxsa(struct macsec_context *ctx)
{
struct macsec_flow *flow = NULL;
if (ctx->prepare)
return __vsc8584_macsec_add_rxsa(ctx, flow, false);
flow = vsc8584_macsec_find_flow(ctx, MACSEC_INGR);
if (IS_ERR(flow))
return PTR_ERR(flow);
vsc8584_macsec_flow_enable(ctx->phydev, flow);
return 0;
}
static int vsc8584_macsec_upd_rxsa(struct macsec_context *ctx)
{
struct macsec_flow *flow;
flow = vsc8584_macsec_find_flow(ctx, MACSEC_INGR);
if (IS_ERR(flow))
return PTR_ERR(flow);
if (ctx->prepare) {
/* Make sure the flow is disabled before updating it */
vsc8584_macsec_flow_disable(ctx->phydev, flow);
return __vsc8584_macsec_add_rxsa(ctx, flow, true);
}
vsc8584_macsec_flow_enable(ctx->phydev, flow);
return 0;
}
static int vsc8584_macsec_del_rxsa(struct macsec_context *ctx)
{
struct macsec_flow *flow;
flow = vsc8584_macsec_find_flow(ctx, MACSEC_INGR);
if (IS_ERR(flow))
return PTR_ERR(flow);
if (ctx->prepare)
return 0;
vsc8584_macsec_del_flow(ctx->phydev, flow);
return 0;
}
static int vsc8584_macsec_add_txsa(struct macsec_context *ctx)
{
struct macsec_flow *flow = NULL;
if (ctx->prepare)
return __vsc8584_macsec_add_txsa(ctx, flow, false);
flow = vsc8584_macsec_find_flow(ctx, MACSEC_EGR);
if (IS_ERR(flow))
return PTR_ERR(flow);
vsc8584_macsec_flow_enable(ctx->phydev, flow);
return 0;
}
static int vsc8584_macsec_upd_txsa(struct macsec_context *ctx)
{
struct macsec_flow *flow;
flow = vsc8584_macsec_find_flow(ctx, MACSEC_EGR);
if (IS_ERR(flow))
return PTR_ERR(flow);
if (ctx->prepare) {
/* Make sure the flow is disabled before updating it */
vsc8584_macsec_flow_disable(ctx->phydev, flow);
return __vsc8584_macsec_add_txsa(ctx, flow, true);
}
vsc8584_macsec_flow_enable(ctx->phydev, flow);
return 0;
}
static int vsc8584_macsec_del_txsa(struct macsec_context *ctx)
{
struct macsec_flow *flow;
flow = vsc8584_macsec_find_flow(ctx, MACSEC_EGR);
if (IS_ERR(flow))
return PTR_ERR(flow);
if (ctx->prepare)
return 0;
vsc8584_macsec_del_flow(ctx->phydev, flow);
return 0;
}
static struct macsec_ops vsc8584_macsec_ops = {
.mdo_dev_open = vsc8584_macsec_dev_open,
.mdo_dev_stop = vsc8584_macsec_dev_stop,
.mdo_add_secy = vsc8584_macsec_add_secy,
.mdo_upd_secy = vsc8584_macsec_upd_secy,
.mdo_del_secy = vsc8584_macsec_del_secy,
.mdo_add_rxsc = vsc8584_macsec_add_rxsc,
.mdo_upd_rxsc = vsc8584_macsec_upd_rxsc,
.mdo_del_rxsc = vsc8584_macsec_del_rxsc,
.mdo_add_rxsa = vsc8584_macsec_add_rxsa,
.mdo_upd_rxsa = vsc8584_macsec_upd_rxsa,
.mdo_del_rxsa = vsc8584_macsec_del_rxsa,
.mdo_add_txsa = vsc8584_macsec_add_txsa,
.mdo_upd_txsa = vsc8584_macsec_upd_txsa,
.mdo_del_txsa = vsc8584_macsec_del_txsa,
};
#endif /* CONFIG_MACSEC */
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
/* Check if one PHY has already done the init of the parts common to all PHYs
* in the Quad PHY package.
*/
static bool vsc8584_is_pkg_init(struct phy_device *phydev, bool reversed)
{
struct mdio_device **map = phydev->mdio.bus->mdio_map;
struct vsc8531_private *vsc8531;
struct phy_device *phy;
int i, addr;
/* VSC8584 is a Quad PHY */
for (i = 0; i < 4; i++) {
vsc8531 = phydev->priv;
if (reversed)
addr = vsc8531->base_addr - i;
else
addr = vsc8531->base_addr + i;
if (!map[addr])
continue;
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
phy = container_of(map[addr], struct phy_device, mdio);
if ((phy->phy_id & phydev->drv->phy_id_mask) !=
(phydev->drv->phy_id & phydev->drv->phy_id_mask))
continue;
vsc8531 = phy->priv;
if (vsc8531 && vsc8531->pkg_init)
return true;
}
return false;
}
static int vsc8584_config_init(struct phy_device *phydev)
{
struct vsc8531_private *vsc8531 = phydev->priv;
u16 addr, val;
int ret, i;
phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
mutex_lock(&phydev->mdio.bus->mdio_lock);
__mdiobus_write(phydev->mdio.bus, phydev->mdio.addr,
MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_EXTENDED);
addr = __mdiobus_read(phydev->mdio.bus, phydev->mdio.addr,
MSCC_PHY_EXT_PHY_CNTL_4);
addr >>= PHY_CNTL_4_ADDR_POS;
val = __mdiobus_read(phydev->mdio.bus, phydev->mdio.addr,
MSCC_PHY_ACTIPHY_CNTL);
if (val & PHY_ADDR_REVERSED)
vsc8531->base_addr = phydev->mdio.addr + addr;
else
vsc8531->base_addr = phydev->mdio.addr - addr;
/* Some parts of the init sequence are identical for every PHY in the
* package. Some parts are modifying the GPIO register bank which is a
* set of registers that are affecting all PHYs, a few resetting the
* microprocessor common to all PHYs. The CRC check responsible of the
* checking the firmware within the 8051 microprocessor can only be
* accessed via the PHY whose internal address in the package is 0.
* All PHYs' interrupts mask register has to be zeroed before enabling
* any PHY's interrupt in this register.
* For all these reasons, we need to do the init sequence once and only
* once whatever is the first PHY in the package that is initialized and
* do the correct init sequence for all PHYs that are package-critical
* in this pre-init function.
*/
if (!vsc8584_is_pkg_init(phydev, val & PHY_ADDR_REVERSED ? 1 : 0)) {
/* The following switch statement assumes that the lowest
* nibble of the phy_id_mask is always 0. This works because
* the lowest nibble of the PHY_ID's below are also 0.
*/
WARN_ON(phydev->drv->phy_id_mask & 0xf);
switch (phydev->phy_id & phydev->drv->phy_id_mask) {
case PHY_ID_VSC8504:
case PHY_ID_VSC8552:
case PHY_ID_VSC8572:
case PHY_ID_VSC8574:
net: phy: mscc: add support for VSC8574 PHY The VSC8574 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports WOL, downshifting and can set the blinking pattern of each of its 4 LEDs, supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, WOL, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8574 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:43 +07:00
ret = vsc8574_config_pre_init(phydev);
break;
case PHY_ID_VSC856X:
case PHY_ID_VSC8575:
case PHY_ID_VSC8582:
case PHY_ID_VSC8584:
net: phy: mscc: add support for VSC8574 PHY The VSC8574 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports WOL, downshifting and can set the blinking pattern of each of its 4 LEDs, supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, WOL, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8574 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:43 +07:00
ret = vsc8584_config_pre_init(phydev);
break;
default:
net: phy: mscc: add support for VSC8574 PHY The VSC8574 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports WOL, downshifting and can set the blinking pattern of each of its 4 LEDs, supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, WOL, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8574 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:43 +07:00
ret = -EINVAL;
break;
}
net: phy: mscc: add support for VSC8574 PHY The VSC8574 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports WOL, downshifting and can set the blinking pattern of each of its 4 LEDs, supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, WOL, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8574 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:43 +07:00
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
if (ret)
goto err;
}
vsc8531->pkg_init = true;
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS,
MSCC_PHY_PAGE_EXTENDED_GPIO);
val = phy_base_read(phydev, MSCC_PHY_MAC_CFG_FASTLINK);
val &= ~MAC_CFG_MASK;
if (phydev->interface == PHY_INTERFACE_MODE_QSGMII)
val |= MAC_CFG_QSGMII;
else
val |= MAC_CFG_SGMII;
ret = phy_base_write(phydev, MSCC_PHY_MAC_CFG_FASTLINK, val);
if (ret)
goto err;
val = PROC_CMD_MCB_ACCESS_MAC_CONF | PROC_CMD_RST_CONF_PORT |
PROC_CMD_READ_MOD_WRITE_PORT;
if (phydev->interface == PHY_INTERFACE_MODE_QSGMII)
val |= PROC_CMD_QSGMII_MAC;
else
val |= PROC_CMD_SGMII_MAC;
ret = vsc8584_cmd(phydev, val);
if (ret)
goto err;
usleep_range(10000, 20000);
/* Disable SerDes for 100Base-FX */
ret = vsc8584_cmd(phydev, PROC_CMD_FIBER_MEDIA_CONF |
PROC_CMD_FIBER_PORT(addr) | PROC_CMD_FIBER_DISABLE |
PROC_CMD_READ_MOD_WRITE_PORT |
PROC_CMD_RST_CONF_PORT | PROC_CMD_FIBER_100BASE_FX);
if (ret)
goto err;
/* Disable SerDes for 1000Base-X */
ret = vsc8584_cmd(phydev, PROC_CMD_FIBER_MEDIA_CONF |
PROC_CMD_FIBER_PORT(addr) | PROC_CMD_FIBER_DISABLE |
PROC_CMD_READ_MOD_WRITE_PORT |
PROC_CMD_RST_CONF_PORT | PROC_CMD_FIBER_1000BASE_X);
if (ret)
goto err;
mutex_unlock(&phydev->mdio.bus->mdio_lock);
#if IS_ENABLED(CONFIG_MACSEC)
/* MACsec */
switch (phydev->phy_id & phydev->drv->phy_id_mask) {
case PHY_ID_VSC856X:
case PHY_ID_VSC8575:
case PHY_ID_VSC8582:
case PHY_ID_VSC8584:
INIT_LIST_HEAD(&vsc8531->macsec_flows);
vsc8531->secy = NULL;
phydev->macsec_ops = &vsc8584_macsec_ops;
ret = vsc8584_macsec_init(phydev);
if (ret)
goto err;
}
#endif
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
phy_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
val = phy_read(phydev, MSCC_PHY_EXT_PHY_CNTL_1);
val &= ~(MEDIA_OP_MODE_MASK | VSC8584_MAC_IF_SELECTION_MASK);
val |= MEDIA_OP_MODE_COPPER | (VSC8584_MAC_IF_SELECTION_SGMII <<
VSC8584_MAC_IF_SELECTION_POS);
ret = phy_write(phydev, MSCC_PHY_EXT_PHY_CNTL_1, val);
ret = genphy_soft_reset(phydev);
if (ret)
return ret;
for (i = 0; i < vsc8531->nleds; i++) {
ret = vsc85xx_led_cntl_set(phydev, i, vsc8531->leds_mode[i]);
if (ret)
return ret;
}
return 0;
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
err:
mutex_unlock(&phydev->mdio.bus->mdio_lock);
return ret;
}
static int vsc8584_handle_interrupt(struct phy_device *phydev)
{
#if IS_ENABLED(CONFIG_MACSEC)
struct vsc8531_private *priv = phydev->priv;
struct macsec_flow *flow, *tmp;
u32 cause, rec;
/* Check MACsec PN rollover */
cause = vsc8584_macsec_phy_read(phydev, MACSEC_EGR,
MSCC_MS_INTR_CTRL_STATUS);
cause &= MSCC_MS_INTR_CTRL_STATUS_INTR_CLR_STATUS_M;
if (!(cause & MACSEC_INTR_CTRL_STATUS_ROLLOVER))
goto skip_rollover;
rec = 6 + priv->secy->key_len / sizeof(u32);
list_for_each_entry_safe(flow, tmp, &priv->macsec_flows, list) {
u32 val;
if (flow->bank != MACSEC_EGR || !flow->has_transformation)
continue;
val = vsc8584_macsec_phy_read(phydev, MACSEC_EGR,
MSCC_MS_XFORM_REC(flow->index, rec));
if (val == 0xffffffff) {
vsc8584_macsec_flow_disable(phydev, flow);
macsec_pn_wrapped(priv->secy, flow->tx_sa);
break;
}
}
skip_rollover:
#endif
phy_mac_interrupt(phydev);
return 0;
}
static int vsc85xx_config_init(struct phy_device *phydev)
{
int rc, i, phy_id;
struct vsc8531_private *vsc8531 = phydev->priv;
rc = vsc85xx_default_config(phydev);
if (rc)
return rc;
rc = vsc85xx_mac_if_set(phydev, phydev->interface);
if (rc)
return rc;
rc = vsc85xx_edge_rate_cntl_set(phydev, vsc8531->rate_magic);
if (rc)
return rc;
phy_id = phydev->drv->phy_id & phydev->drv->phy_id_mask;
if (PHY_ID_VSC8531 == phy_id || PHY_ID_VSC8541 == phy_id ||
PHY_ID_VSC8530 == phy_id || PHY_ID_VSC8540 == phy_id) {
rc = vsc8531_pre_init_seq_set(phydev);
if (rc)
return rc;
}
rc = vsc85xx_eee_init_seq_set(phydev);
if (rc)
return rc;
for (i = 0; i < vsc8531->nleds; i++) {
rc = vsc85xx_led_cntl_set(phydev, i, vsc8531->leds_mode[i]);
if (rc)
return rc;
}
return 0;
}
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
static int vsc8584_did_interrupt(struct phy_device *phydev)
{
int rc = 0;
if (phydev->interrupts == PHY_INTERRUPT_ENABLED)
rc = phy_read(phydev, MII_VSC85XX_INT_STATUS);
return (rc < 0) ? 0 : rc & MII_VSC85XX_INT_MASK_MASK;
}
net: phy: mscc: add support for VSC8514 PHY. The VSC8514 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X, can communicate with the MAC via QSGMII. The MAC interface protocol for each port within QSGMII can be either 1000BASE-X or SGMII, if the QSGMII MAC that the VSC8514 is connecting to supports this functionality. VSC8514 also supports SGMII MAC-side autonegotiation on each individual port, downshifting, can set the blinking pattern of each of its 4 LEDs, SyncE, 1000BASE-T Ring Resiliency as well as HP Auto-MDIX detection. This adds support for 10BASE-T, 100BASE-TX, and 1000BASE-T, QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. Signed-off-by: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com> Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Co-developed-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-22 18:51:35 +07:00
static int vsc8514_config_pre_init(struct phy_device *phydev)
{
/* These are the settings to override the silicon default
* values to handle hardware performance of PHY. They
* are set at Power-On state and remain until PHY Reset.
*/
static const struct reg_val pre_init1[] = {
net: phy: mscc: add support for VSC8514 PHY. The VSC8514 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X, can communicate with the MAC via QSGMII. The MAC interface protocol for each port within QSGMII can be either 1000BASE-X or SGMII, if the QSGMII MAC that the VSC8514 is connecting to supports this functionality. VSC8514 also supports SGMII MAC-side autonegotiation on each individual port, downshifting, can set the blinking pattern of each of its 4 LEDs, SyncE, 1000BASE-T Ring Resiliency as well as HP Auto-MDIX detection. This adds support for 10BASE-T, 100BASE-TX, and 1000BASE-T, QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. Signed-off-by: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com> Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Co-developed-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-22 18:51:35 +07:00
{0x0f90, 0x00688980},
{0x0786, 0x00000003},
{0x07fa, 0x0050100f},
{0x0f82, 0x0012b002},
{0x1686, 0x00000004},
{0x168c, 0x00d2c46f},
{0x17a2, 0x00000620},
{0x16a0, 0x00eeffdd},
{0x16a6, 0x00071448},
{0x16a4, 0x0013132f},
{0x16a8, 0x00000000},
{0x0ffc, 0x00c0a028},
{0x0fe8, 0x0091b06c},
{0x0fea, 0x00041600},
{0x0f80, 0x00fffaff},
{0x0fec, 0x00901809},
{0x0ffe, 0x00b01007},
{0x16b0, 0x00eeff00},
{0x16b2, 0x00007000},
{0x16b4, 0x00000814},
};
unsigned int i;
u16 reg;
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
/* all writes below are broadcasted to all PHYs in the same package */
reg = phy_base_read(phydev, MSCC_PHY_EXT_CNTL_STATUS);
reg |= SMI_BROADCAST_WR_EN;
phy_base_write(phydev, MSCC_PHY_EXT_CNTL_STATUS, reg);
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_TEST);
reg = phy_base_read(phydev, MSCC_PHY_TEST_PAGE_8);
reg |= BIT(15);
phy_base_write(phydev, MSCC_PHY_TEST_PAGE_8, reg);
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_TR);
for (i = 0; i < ARRAY_SIZE(pre_init1); i++)
vsc8584_csr_write(phydev, pre_init1[i].reg, pre_init1[i].val);
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_TEST);
reg = phy_base_read(phydev, MSCC_PHY_TEST_PAGE_8);
reg &= ~BIT(15);
phy_base_write(phydev, MSCC_PHY_TEST_PAGE_8, reg);
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
reg = phy_base_read(phydev, MSCC_PHY_EXT_CNTL_STATUS);
reg &= ~SMI_BROADCAST_WR_EN;
phy_base_write(phydev, MSCC_PHY_EXT_CNTL_STATUS, reg);
return 0;
}
static u32 vsc85xx_csr_ctrl_phy_read(struct phy_device *phydev,
u32 target, u32 reg)
{
unsigned long deadline;
u32 val, val_l, val_h;
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_CSR_CNTL);
/* CSR registers are grouped under different Target IDs.
* 6-bit Target_ID is split between MSCC_EXT_PAGE_CSR_CNTL_20 and
* MSCC_EXT_PAGE_CSR_CNTL_19 registers.
* Target_ID[5:2] maps to bits[3:0] of MSCC_EXT_PAGE_CSR_CNTL_20
* and Target_ID[1:0] maps to bits[13:12] of MSCC_EXT_PAGE_CSR_CNTL_19.
*/
/* Setup the Target ID */
phy_base_write(phydev, MSCC_EXT_PAGE_CSR_CNTL_20,
MSCC_PHY_CSR_CNTL_20_TARGET(target >> 2));
/* Trigger CSR Action - Read into the CSR's */
phy_base_write(phydev, MSCC_EXT_PAGE_CSR_CNTL_19,
MSCC_PHY_CSR_CNTL_19_CMD | MSCC_PHY_CSR_CNTL_19_READ |
MSCC_PHY_CSR_CNTL_19_REG_ADDR(reg) |
MSCC_PHY_CSR_CNTL_19_TARGET(target & 0x3));
/* Wait for register access*/
deadline = jiffies + msecs_to_jiffies(PROC_CMD_NCOMPLETED_TIMEOUT_MS);
do {
usleep_range(500, 1000);
val = phy_base_read(phydev, MSCC_EXT_PAGE_CSR_CNTL_19);
} while (time_before(jiffies, deadline) &&
!(val & MSCC_PHY_CSR_CNTL_19_CMD));
if (!(val & MSCC_PHY_CSR_CNTL_19_CMD))
return 0xffffffff;
/* Read the Least Significant Word (LSW) (17) */
val_l = phy_base_read(phydev, MSCC_EXT_PAGE_CSR_CNTL_17);
/* Read the Most Significant Word (MSW) (18) */
val_h = phy_base_read(phydev, MSCC_EXT_PAGE_CSR_CNTL_18);
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS,
MSCC_PHY_PAGE_STANDARD);
return (val_h << 16) | val_l;
}
static int vsc85xx_csr_ctrl_phy_write(struct phy_device *phydev,
u32 target, u32 reg, u32 val)
{
unsigned long deadline;
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_CSR_CNTL);
/* CSR registers are grouped under different Target IDs.
* 6-bit Target_ID is split between MSCC_EXT_PAGE_CSR_CNTL_20 and
* MSCC_EXT_PAGE_CSR_CNTL_19 registers.
* Target_ID[5:2] maps to bits[3:0] of MSCC_EXT_PAGE_CSR_CNTL_20
* and Target_ID[1:0] maps to bits[13:12] of MSCC_EXT_PAGE_CSR_CNTL_19.
*/
/* Setup the Target ID */
phy_base_write(phydev, MSCC_EXT_PAGE_CSR_CNTL_20,
MSCC_PHY_CSR_CNTL_20_TARGET(target >> 2));
/* Write the Least Significant Word (LSW) (17) */
phy_base_write(phydev, MSCC_EXT_PAGE_CSR_CNTL_17, (u16)val);
/* Write the Most Significant Word (MSW) (18) */
phy_base_write(phydev, MSCC_EXT_PAGE_CSR_CNTL_18, (u16)(val >> 16));
/* Trigger CSR Action - Write into the CSR's */
phy_base_write(phydev, MSCC_EXT_PAGE_CSR_CNTL_19,
MSCC_PHY_CSR_CNTL_19_CMD |
MSCC_PHY_CSR_CNTL_19_REG_ADDR(reg) |
MSCC_PHY_CSR_CNTL_19_TARGET(target & 0x3));
/* Wait for register access */
deadline = jiffies + msecs_to_jiffies(PROC_CMD_NCOMPLETED_TIMEOUT_MS);
do {
usleep_range(500, 1000);
val = phy_base_read(phydev, MSCC_EXT_PAGE_CSR_CNTL_19);
} while (time_before(jiffies, deadline) &&
!(val & MSCC_PHY_CSR_CNTL_19_CMD));
if (!(val & MSCC_PHY_CSR_CNTL_19_CMD))
return -ETIMEDOUT;
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS,
MSCC_PHY_PAGE_STANDARD);
return 0;
}
static int __phy_write_mcb_s6g(struct phy_device *phydev, u32 reg, u8 mcb,
u32 op)
{
unsigned long deadline;
u32 val;
int ret;
ret = vsc85xx_csr_ctrl_phy_write(phydev, PHY_MCB_TARGET, reg,
op | (1 << mcb));
if (ret)
return -EINVAL;
deadline = jiffies + msecs_to_jiffies(PROC_CMD_NCOMPLETED_TIMEOUT_MS);
do {
usleep_range(500, 1000);
val = vsc85xx_csr_ctrl_phy_read(phydev, PHY_MCB_TARGET, reg);
if (val == 0xffffffff)
return -EIO;
} while (time_before(jiffies, deadline) && (val & op));
if (val & op)
return -ETIMEDOUT;
return 0;
}
/* Trigger a read to the spcified MCB */
static int phy_update_mcb_s6g(struct phy_device *phydev, u32 reg, u8 mcb)
{
return __phy_write_mcb_s6g(phydev, reg, mcb, PHY_MCB_S6G_READ);
}
/* Trigger a write to the spcified MCB */
static int phy_commit_mcb_s6g(struct phy_device *phydev, u32 reg, u8 mcb)
{
return __phy_write_mcb_s6g(phydev, reg, mcb, PHY_MCB_S6G_WRITE);
}
static int vsc8514_config_init(struct phy_device *phydev)
{
struct vsc8531_private *vsc8531 = phydev->priv;
unsigned long deadline;
u16 val, addr;
int ret, i;
u32 reg;
phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
mutex_lock(&phydev->mdio.bus->mdio_lock);
__phy_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_EXTENDED);
addr = __phy_read(phydev, MSCC_PHY_EXT_PHY_CNTL_4);
addr >>= PHY_CNTL_4_ADDR_POS;
val = __phy_read(phydev, MSCC_PHY_ACTIPHY_CNTL);
if (val & PHY_ADDR_REVERSED)
vsc8531->base_addr = phydev->mdio.addr + addr;
else
vsc8531->base_addr = phydev->mdio.addr - addr;
/* Some parts of the init sequence are identical for every PHY in the
* package. Some parts are modifying the GPIO register bank which is a
* set of registers that are affecting all PHYs, a few resetting the
* microprocessor common to all PHYs.
* All PHYs' interrupts mask register has to be zeroed before enabling
* any PHY's interrupt in this register.
* For all these reasons, we need to do the init sequence once and only
* once whatever is the first PHY in the package that is initialized and
* do the correct init sequence for all PHYs that are package-critical
* in this pre-init function.
*/
if (!vsc8584_is_pkg_init(phydev, val & PHY_ADDR_REVERSED ? 1 : 0))
vsc8514_config_pre_init(phydev);
vsc8531->pkg_init = true;
phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS,
MSCC_PHY_PAGE_EXTENDED_GPIO);
val = phy_base_read(phydev, MSCC_PHY_MAC_CFG_FASTLINK);
val &= ~MAC_CFG_MASK;
val |= MAC_CFG_QSGMII;
ret = phy_base_write(phydev, MSCC_PHY_MAC_CFG_FASTLINK, val);
if (ret)
goto err;
ret = vsc8584_cmd(phydev,
PROC_CMD_MCB_ACCESS_MAC_CONF |
PROC_CMD_RST_CONF_PORT |
PROC_CMD_READ_MOD_WRITE_PORT | PROC_CMD_QSGMII_MAC);
if (ret)
goto err;
/* 6g mcb */
phy_update_mcb_s6g(phydev, PHY_MCB_S6G_CFG, 0);
/* lcpll mcb */
phy_update_mcb_s6g(phydev, PHY_S6G_LCPLL_CFG, 0);
/* pll5gcfg0 */
ret = vsc85xx_csr_ctrl_phy_write(phydev, PHY_MCB_TARGET,
PHY_S6G_PLL5G_CFG0, 0x7036f145);
if (ret)
goto err;
phy_commit_mcb_s6g(phydev, PHY_S6G_LCPLL_CFG, 0);
/* pllcfg */
ret = vsc85xx_csr_ctrl_phy_write(phydev, PHY_MCB_TARGET,
PHY_S6G_PLL_CFG,
(3 << PHY_S6G_PLL_ENA_OFFS_POS) |
(120 << PHY_S6G_PLL_FSM_CTRL_DATA_POS)
| (0 << PHY_S6G_PLL_FSM_ENA_POS));
if (ret)
goto err;
/* commoncfg */
ret = vsc85xx_csr_ctrl_phy_write(phydev, PHY_MCB_TARGET,
PHY_S6G_COMMON_CFG,
(0 << PHY_S6G_SYS_RST_POS) |
(0 << PHY_S6G_ENA_LANE_POS) |
(0 << PHY_S6G_ENA_LOOP_POS) |
(0 << PHY_S6G_QRATE_POS) |
(3 << PHY_S6G_IF_MODE_POS));
if (ret)
goto err;
/* misccfg */
ret = vsc85xx_csr_ctrl_phy_write(phydev, PHY_MCB_TARGET,
PHY_S6G_MISC_CFG, 1);
if (ret)
goto err;
/* gpcfg */
ret = vsc85xx_csr_ctrl_phy_write(phydev, PHY_MCB_TARGET,
PHY_S6G_GPC_CFG, 768);
if (ret)
goto err;
phy_commit_mcb_s6g(phydev, PHY_S6G_DFT_CFG2, 0);
deadline = jiffies + msecs_to_jiffies(PROC_CMD_NCOMPLETED_TIMEOUT_MS);
do {
usleep_range(500, 1000);
phy_update_mcb_s6g(phydev, PHY_MCB_S6G_CFG,
0); /* read 6G MCB into CSRs */
reg = vsc85xx_csr_ctrl_phy_read(phydev, PHY_MCB_TARGET,
PHY_S6G_PLL_STATUS);
if (reg == 0xffffffff) {
mutex_unlock(&phydev->mdio.bus->mdio_lock);
return -EIO;
}
} while (time_before(jiffies, deadline) && (reg & BIT(12)));
if (reg & BIT(12)) {
mutex_unlock(&phydev->mdio.bus->mdio_lock);
return -ETIMEDOUT;
}
/* misccfg */
ret = vsc85xx_csr_ctrl_phy_write(phydev, PHY_MCB_TARGET,
PHY_S6G_MISC_CFG, 0);
if (ret)
goto err;
phy_commit_mcb_s6g(phydev, PHY_MCB_S6G_CFG, 0);
deadline = jiffies + msecs_to_jiffies(PROC_CMD_NCOMPLETED_TIMEOUT_MS);
do {
usleep_range(500, 1000);
phy_update_mcb_s6g(phydev, PHY_MCB_S6G_CFG,
0); /* read 6G MCB into CSRs */
reg = vsc85xx_csr_ctrl_phy_read(phydev, PHY_MCB_TARGET,
PHY_S6G_IB_STATUS0);
if (reg == 0xffffffff) {
mutex_unlock(&phydev->mdio.bus->mdio_lock);
return -EIO;
}
} while (time_before(jiffies, deadline) && !(reg & BIT(8)));
if (!(reg & BIT(8))) {
mutex_unlock(&phydev->mdio.bus->mdio_lock);
return -ETIMEDOUT;
}
mutex_unlock(&phydev->mdio.bus->mdio_lock);
ret = phy_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
if (ret)
return ret;
ret = phy_modify(phydev, MSCC_PHY_EXT_PHY_CNTL_1, MEDIA_OP_MODE_MASK,
MEDIA_OP_MODE_COPPER);
if (ret)
return ret;
ret = genphy_soft_reset(phydev);
if (ret)
return ret;
for (i = 0; i < vsc8531->nleds; i++) {
ret = vsc85xx_led_cntl_set(phydev, i, vsc8531->leds_mode[i]);
if (ret)
return ret;
}
return ret;
err:
mutex_unlock(&phydev->mdio.bus->mdio_lock);
return ret;
}
static int vsc85xx_ack_interrupt(struct phy_device *phydev)
{
int rc = 0;
if (phydev->interrupts == PHY_INTERRUPT_ENABLED)
rc = phy_read(phydev, MII_VSC85XX_INT_STATUS);
return (rc < 0) ? rc : 0;
}
static int vsc85xx_config_intr(struct phy_device *phydev)
{
int rc;
if (phydev->interrupts == PHY_INTERRUPT_ENABLED) {
#if IS_ENABLED(CONFIG_MACSEC)
phy_write(phydev, MSCC_EXT_PAGE_ACCESS,
MSCC_PHY_PAGE_EXTENDED_2);
phy_write(phydev, MSCC_PHY_EXTENDED_INT,
MSCC_PHY_EXTENDED_INT_MS_EGR);
phy_write(phydev, MSCC_EXT_PAGE_ACCESS,
MSCC_PHY_PAGE_STANDARD);
vsc8584_macsec_phy_write(phydev, MACSEC_EGR,
MSCC_MS_AIC_CTRL, 0xf);
vsc8584_macsec_phy_write(phydev, MACSEC_EGR,
MSCC_MS_INTR_CTRL_STATUS,
MSCC_MS_INTR_CTRL_STATUS_INTR_ENABLE(MACSEC_INTR_CTRL_STATUS_ROLLOVER));
#endif
rc = phy_write(phydev, MII_VSC85XX_INT_MASK,
MII_VSC85XX_INT_MASK_MASK);
} else {
rc = phy_write(phydev, MII_VSC85XX_INT_MASK, 0);
if (rc < 0)
return rc;
rc = phy_read(phydev, MII_VSC85XX_INT_STATUS);
}
return rc;
}
static int vsc85xx_config_aneg(struct phy_device *phydev)
{
int rc;
rc = vsc85xx_mdix_set(phydev, phydev->mdix_ctrl);
if (rc < 0)
return rc;
return genphy_config_aneg(phydev);
}
static int vsc85xx_read_status(struct phy_device *phydev)
{
int rc;
rc = vsc85xx_mdix_get(phydev, &phydev->mdix);
if (rc < 0)
return rc;
return genphy_read_status(phydev);
}
net: phy: mscc: add support for VSC8514 PHY. The VSC8514 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X, can communicate with the MAC via QSGMII. The MAC interface protocol for each port within QSGMII can be either 1000BASE-X or SGMII, if the QSGMII MAC that the VSC8514 is connecting to supports this functionality. VSC8514 also supports SGMII MAC-side autonegotiation on each individual port, downshifting, can set the blinking pattern of each of its 4 LEDs, SyncE, 1000BASE-T Ring Resiliency as well as HP Auto-MDIX detection. This adds support for 10BASE-T, 100BASE-TX, and 1000BASE-T, QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. Signed-off-by: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com> Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Co-developed-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-22 18:51:35 +07:00
static int vsc8514_probe(struct phy_device *phydev)
{
struct vsc8531_private *vsc8531;
u32 default_mode[4] = {VSC8531_LINK_1000_ACTIVITY,
VSC8531_LINK_100_ACTIVITY, VSC8531_LINK_ACTIVITY,
VSC8531_DUPLEX_COLLISION};
vsc8531 = devm_kzalloc(&phydev->mdio.dev, sizeof(*vsc8531), GFP_KERNEL);
if (!vsc8531)
return -ENOMEM;
phydev->priv = vsc8531;
vsc8531->nleds = 4;
vsc8531->supp_led_modes = VSC85XX_SUPP_LED_MODES;
vsc8531->hw_stats = vsc85xx_hw_stats;
vsc8531->nstats = ARRAY_SIZE(vsc85xx_hw_stats);
vsc8531->stats = devm_kcalloc(&phydev->mdio.dev, vsc8531->nstats,
sizeof(u64), GFP_KERNEL);
net: phy: mscc: add support for VSC8514 PHY. The VSC8514 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X, can communicate with the MAC via QSGMII. The MAC interface protocol for each port within QSGMII can be either 1000BASE-X or SGMII, if the QSGMII MAC that the VSC8514 is connecting to supports this functionality. VSC8514 also supports SGMII MAC-side autonegotiation on each individual port, downshifting, can set the blinking pattern of each of its 4 LEDs, SyncE, 1000BASE-T Ring Resiliency as well as HP Auto-MDIX detection. This adds support for 10BASE-T, 100BASE-TX, and 1000BASE-T, QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. Signed-off-by: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com> Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Co-developed-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-22 18:51:35 +07:00
if (!vsc8531->stats)
return -ENOMEM;
return vsc85xx_dt_led_modes_get(phydev, default_mode);
}
net: phy: mscc: add support for VSC8574 PHY The VSC8574 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports WOL, downshifting and can set the blinking pattern of each of its 4 LEDs, supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, WOL, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8574 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:43 +07:00
static int vsc8574_probe(struct phy_device *phydev)
{
struct vsc8531_private *vsc8531;
u32 default_mode[4] = {VSC8531_LINK_1000_ACTIVITY,
VSC8531_LINK_100_ACTIVITY, VSC8531_LINK_ACTIVITY,
VSC8531_DUPLEX_COLLISION};
vsc8531 = devm_kzalloc(&phydev->mdio.dev, sizeof(*vsc8531), GFP_KERNEL);
if (!vsc8531)
return -ENOMEM;
phydev->priv = vsc8531;
vsc8531->nleds = 4;
vsc8531->supp_led_modes = VSC8584_SUPP_LED_MODES;
vsc8531->hw_stats = vsc8584_hw_stats;
vsc8531->nstats = ARRAY_SIZE(vsc8584_hw_stats);
vsc8531->stats = devm_kcalloc(&phydev->mdio.dev, vsc8531->nstats,
sizeof(u64), GFP_KERNEL);
net: phy: mscc: add support for VSC8574 PHY The VSC8574 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports WOL, downshifting and can set the blinking pattern of each of its 4 LEDs, supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, WOL, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8574 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:43 +07:00
if (!vsc8531->stats)
return -ENOMEM;
return vsc85xx_dt_led_modes_get(phydev, default_mode);
}
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
static int vsc8584_probe(struct phy_device *phydev)
{
struct vsc8531_private *vsc8531;
u32 default_mode[4] = {VSC8531_LINK_1000_ACTIVITY,
VSC8531_LINK_100_ACTIVITY, VSC8531_LINK_ACTIVITY,
VSC8531_DUPLEX_COLLISION};
if ((phydev->phy_id & MSCC_DEV_REV_MASK) != VSC8584_REVB) {
dev_err(&phydev->mdio.dev, "Only VSC8584 revB is supported.\n");
return -ENOTSUPP;
}
vsc8531 = devm_kzalloc(&phydev->mdio.dev, sizeof(*vsc8531), GFP_KERNEL);
if (!vsc8531)
return -ENOMEM;
phydev->priv = vsc8531;
vsc8531->nleds = 4;
vsc8531->supp_led_modes = VSC8584_SUPP_LED_MODES;
vsc8531->hw_stats = vsc8584_hw_stats;
vsc8531->nstats = ARRAY_SIZE(vsc8584_hw_stats);
vsc8531->stats = devm_kcalloc(&phydev->mdio.dev, vsc8531->nstats,
sizeof(u64), GFP_KERNEL);
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
if (!vsc8531->stats)
return -ENOMEM;
return vsc85xx_dt_led_modes_get(phydev, default_mode);
}
static int vsc85xx_probe(struct phy_device *phydev)
{
struct vsc8531_private *vsc8531;
int rate_magic;
u32 default_mode[2] = {VSC8531_LINK_1000_ACTIVITY,
VSC8531_LINK_100_ACTIVITY};
rate_magic = vsc85xx_edge_rate_magic_get(phydev);
if (rate_magic < 0)
return rate_magic;
vsc8531 = devm_kzalloc(&phydev->mdio.dev, sizeof(*vsc8531), GFP_KERNEL);
if (!vsc8531)
return -ENOMEM;
phydev->priv = vsc8531;
vsc8531->rate_magic = rate_magic;
vsc8531->nleds = 2;
vsc8531->supp_led_modes = VSC85XX_SUPP_LED_MODES;
vsc8531->hw_stats = vsc85xx_hw_stats;
vsc8531->nstats = ARRAY_SIZE(vsc85xx_hw_stats);
vsc8531->stats = devm_kcalloc(&phydev->mdio.dev, vsc8531->nstats,
sizeof(u64), GFP_KERNEL);
if (!vsc8531->stats)
return -ENOMEM;
return vsc85xx_dt_led_modes_get(phydev, default_mode);
}
/* Microsemi VSC85xx PHYs */
static struct phy_driver vsc85xx_driver[] = {
{
.phy_id = PHY_ID_VSC8504,
.name = "Microsemi GE VSC8504 SyncE",
.phy_id_mask = 0xfffffff0,
/* PHY_GBIT_FEATURES */
.soft_reset = &genphy_soft_reset,
.config_init = &vsc8584_config_init,
.config_aneg = &vsc85xx_config_aneg,
.aneg_done = &genphy_aneg_done,
.read_status = &vsc85xx_read_status,
.ack_interrupt = &vsc85xx_ack_interrupt,
.config_intr = &vsc85xx_config_intr,
.did_interrupt = &vsc8584_did_interrupt,
.suspend = &genphy_suspend,
.resume = &genphy_resume,
.probe = &vsc8574_probe,
.set_wol = &vsc85xx_wol_set,
.get_wol = &vsc85xx_wol_get,
.get_tunable = &vsc85xx_get_tunable,
.set_tunable = &vsc85xx_set_tunable,
.read_page = &vsc85xx_phy_read_page,
.write_page = &vsc85xx_phy_write_page,
.get_sset_count = &vsc85xx_get_sset_count,
.get_strings = &vsc85xx_get_strings,
.get_stats = &vsc85xx_get_stats,
},
net: phy: mscc: add support for VSC8514 PHY. The VSC8514 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X, can communicate with the MAC via QSGMII. The MAC interface protocol for each port within QSGMII can be either 1000BASE-X or SGMII, if the QSGMII MAC that the VSC8514 is connecting to supports this functionality. VSC8514 also supports SGMII MAC-side autonegotiation on each individual port, downshifting, can set the blinking pattern of each of its 4 LEDs, SyncE, 1000BASE-T Ring Resiliency as well as HP Auto-MDIX detection. This adds support for 10BASE-T, 100BASE-TX, and 1000BASE-T, QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. Signed-off-by: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com> Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Co-developed-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-22 18:51:35 +07:00
{
.phy_id = PHY_ID_VSC8514,
.name = "Microsemi GE VSC8514 SyncE",
.phy_id_mask = 0xfffffff0,
.soft_reset = &genphy_soft_reset,
.config_init = &vsc8514_config_init,
.config_aneg = &vsc85xx_config_aneg,
.read_status = &vsc85xx_read_status,
.ack_interrupt = &vsc85xx_ack_interrupt,
.config_intr = &vsc85xx_config_intr,
.suspend = &genphy_suspend,
.resume = &genphy_resume,
.probe = &vsc8514_probe,
.set_wol = &vsc85xx_wol_set,
.get_wol = &vsc85xx_wol_get,
.get_tunable = &vsc85xx_get_tunable,
.set_tunable = &vsc85xx_set_tunable,
.read_page = &vsc85xx_phy_read_page,
.write_page = &vsc85xx_phy_write_page,
.get_sset_count = &vsc85xx_get_sset_count,
.get_strings = &vsc85xx_get_strings,
.get_stats = &vsc85xx_get_stats,
},
{
.phy_id = PHY_ID_VSC8530,
.name = "Microsemi FE VSC8530",
.phy_id_mask = 0xfffffff0,
/* PHY_BASIC_FEATURES */
.soft_reset = &genphy_soft_reset,
.config_init = &vsc85xx_config_init,
.config_aneg = &vsc85xx_config_aneg,
.read_status = &vsc85xx_read_status,
.ack_interrupt = &vsc85xx_ack_interrupt,
.config_intr = &vsc85xx_config_intr,
.suspend = &genphy_suspend,
.resume = &genphy_resume,
.probe = &vsc85xx_probe,
.set_wol = &vsc85xx_wol_set,
.get_wol = &vsc85xx_wol_get,
.get_tunable = &vsc85xx_get_tunable,
.set_tunable = &vsc85xx_set_tunable,
.read_page = &vsc85xx_phy_read_page,
.write_page = &vsc85xx_phy_write_page,
.get_sset_count = &vsc85xx_get_sset_count,
.get_strings = &vsc85xx_get_strings,
.get_stats = &vsc85xx_get_stats,
},
{
.phy_id = PHY_ID_VSC8531,
.name = "Microsemi VSC8531",
.phy_id_mask = 0xfffffff0,
/* PHY_GBIT_FEATURES */
.soft_reset = &genphy_soft_reset,
.config_init = &vsc85xx_config_init,
.config_aneg = &vsc85xx_config_aneg,
.read_status = &vsc85xx_read_status,
.ack_interrupt = &vsc85xx_ack_interrupt,
.config_intr = &vsc85xx_config_intr,
.suspend = &genphy_suspend,
.resume = &genphy_resume,
.probe = &vsc85xx_probe,
.set_wol = &vsc85xx_wol_set,
.get_wol = &vsc85xx_wol_get,
.get_tunable = &vsc85xx_get_tunable,
.set_tunable = &vsc85xx_set_tunable,
.read_page = &vsc85xx_phy_read_page,
.write_page = &vsc85xx_phy_write_page,
.get_sset_count = &vsc85xx_get_sset_count,
.get_strings = &vsc85xx_get_strings,
.get_stats = &vsc85xx_get_stats,
},
{
.phy_id = PHY_ID_VSC8540,
.name = "Microsemi FE VSC8540 SyncE",
.phy_id_mask = 0xfffffff0,
/* PHY_BASIC_FEATURES */
.soft_reset = &genphy_soft_reset,
.config_init = &vsc85xx_config_init,
.config_aneg = &vsc85xx_config_aneg,
.read_status = &vsc85xx_read_status,
.ack_interrupt = &vsc85xx_ack_interrupt,
.config_intr = &vsc85xx_config_intr,
.suspend = &genphy_suspend,
.resume = &genphy_resume,
.probe = &vsc85xx_probe,
.set_wol = &vsc85xx_wol_set,
.get_wol = &vsc85xx_wol_get,
.get_tunable = &vsc85xx_get_tunable,
.set_tunable = &vsc85xx_set_tunable,
.read_page = &vsc85xx_phy_read_page,
.write_page = &vsc85xx_phy_write_page,
.get_sset_count = &vsc85xx_get_sset_count,
.get_strings = &vsc85xx_get_strings,
.get_stats = &vsc85xx_get_stats,
},
{
.phy_id = PHY_ID_VSC8541,
.name = "Microsemi VSC8541 SyncE",
.phy_id_mask = 0xfffffff0,
/* PHY_GBIT_FEATURES */
.soft_reset = &genphy_soft_reset,
.config_init = &vsc85xx_config_init,
.config_aneg = &vsc85xx_config_aneg,
.read_status = &vsc85xx_read_status,
.ack_interrupt = &vsc85xx_ack_interrupt,
.config_intr = &vsc85xx_config_intr,
.suspend = &genphy_suspend,
.resume = &genphy_resume,
.probe = &vsc85xx_probe,
.set_wol = &vsc85xx_wol_set,
.get_wol = &vsc85xx_wol_get,
.get_tunable = &vsc85xx_get_tunable,
.set_tunable = &vsc85xx_set_tunable,
.read_page = &vsc85xx_phy_read_page,
.write_page = &vsc85xx_phy_write_page,
.get_sset_count = &vsc85xx_get_sset_count,
.get_strings = &vsc85xx_get_strings,
.get_stats = &vsc85xx_get_stats,
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
},
{
.phy_id = PHY_ID_VSC8552,
.name = "Microsemi GE VSC8552 SyncE",
.phy_id_mask = 0xfffffff0,
/* PHY_GBIT_FEATURES */
.soft_reset = &genphy_soft_reset,
.config_init = &vsc8584_config_init,
.config_aneg = &vsc85xx_config_aneg,
.read_status = &vsc85xx_read_status,
.ack_interrupt = &vsc85xx_ack_interrupt,
.config_intr = &vsc85xx_config_intr,
.did_interrupt = &vsc8584_did_interrupt,
.suspend = &genphy_suspend,
.resume = &genphy_resume,
.probe = &vsc8574_probe,
.set_wol = &vsc85xx_wol_set,
.get_wol = &vsc85xx_wol_get,
.get_tunable = &vsc85xx_get_tunable,
.set_tunable = &vsc85xx_set_tunable,
.read_page = &vsc85xx_phy_read_page,
.write_page = &vsc85xx_phy_write_page,
.get_sset_count = &vsc85xx_get_sset_count,
.get_strings = &vsc85xx_get_strings,
.get_stats = &vsc85xx_get_stats,
},
{
.phy_id = PHY_ID_VSC856X,
.name = "Microsemi GE VSC856X SyncE",
.phy_id_mask = 0xfffffff0,
/* PHY_GBIT_FEATURES */
.soft_reset = &genphy_soft_reset,
.config_init = &vsc8584_config_init,
.config_aneg = &vsc85xx_config_aneg,
.read_status = &vsc85xx_read_status,
.ack_interrupt = &vsc85xx_ack_interrupt,
.config_intr = &vsc85xx_config_intr,
.did_interrupt = &vsc8584_did_interrupt,
.suspend = &genphy_suspend,
.resume = &genphy_resume,
.probe = &vsc8584_probe,
.get_tunable = &vsc85xx_get_tunable,
.set_tunable = &vsc85xx_set_tunable,
.read_page = &vsc85xx_phy_read_page,
.write_page = &vsc85xx_phy_write_page,
.get_sset_count = &vsc85xx_get_sset_count,
.get_strings = &vsc85xx_get_strings,
.get_stats = &vsc85xx_get_stats,
},
{
.phy_id = PHY_ID_VSC8572,
.name = "Microsemi GE VSC8572 SyncE",
.phy_id_mask = 0xfffffff0,
/* PHY_GBIT_FEATURES */
.soft_reset = &genphy_soft_reset,
.config_init = &vsc8584_config_init,
.config_aneg = &vsc85xx_config_aneg,
.aneg_done = &genphy_aneg_done,
.read_status = &vsc85xx_read_status,
.handle_interrupt = &vsc8584_handle_interrupt,
.ack_interrupt = &vsc85xx_ack_interrupt,
.config_intr = &vsc85xx_config_intr,
.did_interrupt = &vsc8584_did_interrupt,
.suspend = &genphy_suspend,
.resume = &genphy_resume,
.probe = &vsc8574_probe,
.set_wol = &vsc85xx_wol_set,
.get_wol = &vsc85xx_wol_get,
.get_tunable = &vsc85xx_get_tunable,
.set_tunable = &vsc85xx_set_tunable,
.read_page = &vsc85xx_phy_read_page,
.write_page = &vsc85xx_phy_write_page,
.get_sset_count = &vsc85xx_get_sset_count,
.get_strings = &vsc85xx_get_strings,
.get_stats = &vsc85xx_get_stats,
},
net: phy: mscc: add support for VSC8574 PHY The VSC8574 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports WOL, downshifting and can set the blinking pattern of each of its 4 LEDs, supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, WOL, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8574 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:43 +07:00
{
.phy_id = PHY_ID_VSC8574,
.name = "Microsemi GE VSC8574 SyncE",
.phy_id_mask = 0xfffffff0,
/* PHY_GBIT_FEATURES */
net: phy: mscc: add support for VSC8574 PHY The VSC8574 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports WOL, downshifting and can set the blinking pattern of each of its 4 LEDs, supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, WOL, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8574 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:43 +07:00
.soft_reset = &genphy_soft_reset,
.config_init = &vsc8584_config_init,
.config_aneg = &vsc85xx_config_aneg,
.aneg_done = &genphy_aneg_done,
.read_status = &vsc85xx_read_status,
.ack_interrupt = &vsc85xx_ack_interrupt,
.config_intr = &vsc85xx_config_intr,
.did_interrupt = &vsc8584_did_interrupt,
.suspend = &genphy_suspend,
.resume = &genphy_resume,
.probe = &vsc8574_probe,
.set_wol = &vsc85xx_wol_set,
.get_wol = &vsc85xx_wol_get,
.get_tunable = &vsc85xx_get_tunable,
.set_tunable = &vsc85xx_set_tunable,
.read_page = &vsc85xx_phy_read_page,
.write_page = &vsc85xx_phy_write_page,
.get_sset_count = &vsc85xx_get_sset_count,
.get_strings = &vsc85xx_get_strings,
.get_stats = &vsc85xx_get_stats,
},
{
.phy_id = PHY_ID_VSC8575,
.name = "Microsemi GE VSC8575 SyncE",
.phy_id_mask = 0xfffffff0,
/* PHY_GBIT_FEATURES */
.soft_reset = &genphy_soft_reset,
.config_init = &vsc8584_config_init,
.config_aneg = &vsc85xx_config_aneg,
.aneg_done = &genphy_aneg_done,
.read_status = &vsc85xx_read_status,
.handle_interrupt = &vsc8584_handle_interrupt,
.ack_interrupt = &vsc85xx_ack_interrupt,
.config_intr = &vsc85xx_config_intr,
.did_interrupt = &vsc8584_did_interrupt,
.suspend = &genphy_suspend,
.resume = &genphy_resume,
.probe = &vsc8584_probe,
.get_tunable = &vsc85xx_get_tunable,
.set_tunable = &vsc85xx_set_tunable,
.read_page = &vsc85xx_phy_read_page,
.write_page = &vsc85xx_phy_write_page,
.get_sset_count = &vsc85xx_get_sset_count,
.get_strings = &vsc85xx_get_strings,
.get_stats = &vsc85xx_get_stats,
},
{
.phy_id = PHY_ID_VSC8582,
.name = "Microsemi GE VSC8582 SyncE",
.phy_id_mask = 0xfffffff0,
/* PHY_GBIT_FEATURES */
.soft_reset = &genphy_soft_reset,
.config_init = &vsc8584_config_init,
.config_aneg = &vsc85xx_config_aneg,
.aneg_done = &genphy_aneg_done,
.read_status = &vsc85xx_read_status,
.handle_interrupt = &vsc8584_handle_interrupt,
.ack_interrupt = &vsc85xx_ack_interrupt,
.config_intr = &vsc85xx_config_intr,
.did_interrupt = &vsc8584_did_interrupt,
.suspend = &genphy_suspend,
.resume = &genphy_resume,
.probe = &vsc8584_probe,
.get_tunable = &vsc85xx_get_tunable,
.set_tunable = &vsc85xx_set_tunable,
.read_page = &vsc85xx_phy_read_page,
.write_page = &vsc85xx_phy_write_page,
.get_sset_count = &vsc85xx_get_sset_count,
.get_strings = &vsc85xx_get_strings,
.get_stats = &vsc85xx_get_stats,
},
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
{
.phy_id = PHY_ID_VSC8584,
.name = "Microsemi GE VSC8584 SyncE",
.phy_id_mask = 0xfffffff0,
/* PHY_GBIT_FEATURES */
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
.soft_reset = &genphy_soft_reset,
.config_init = &vsc8584_config_init,
.config_aneg = &vsc85xx_config_aneg,
.aneg_done = &genphy_aneg_done,
.read_status = &vsc85xx_read_status,
.handle_interrupt = &vsc8584_handle_interrupt,
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
.ack_interrupt = &vsc85xx_ack_interrupt,
.config_intr = &vsc85xx_config_intr,
.did_interrupt = &vsc8584_did_interrupt,
.suspend = &genphy_suspend,
.resume = &genphy_resume,
.probe = &vsc8584_probe,
.get_tunable = &vsc85xx_get_tunable,
.set_tunable = &vsc85xx_set_tunable,
.read_page = &vsc85xx_phy_read_page,
.write_page = &vsc85xx_phy_write_page,
.get_sset_count = &vsc85xx_get_sset_count,
.get_strings = &vsc85xx_get_strings,
.get_stats = &vsc85xx_get_stats,
}
};
module_phy_driver(vsc85xx_driver);
static struct mdio_device_id __maybe_unused vsc85xx_tbl[] = {
{ PHY_ID_VSC8504, 0xfffffff0, },
net: phy: mscc: add support for VSC8514 PHY. The VSC8514 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X, can communicate with the MAC via QSGMII. The MAC interface protocol for each port within QSGMII can be either 1000BASE-X or SGMII, if the QSGMII MAC that the VSC8514 is connecting to supports this functionality. VSC8514 also supports SGMII MAC-side autonegotiation on each individual port, downshifting, can set the blinking pattern of each of its 4 LEDs, SyncE, 1000BASE-T Ring Resiliency as well as HP Auto-MDIX detection. This adds support for 10BASE-T, 100BASE-TX, and 1000BASE-T, QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. Signed-off-by: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com> Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Co-developed-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-22 18:51:35 +07:00
{ PHY_ID_VSC8514, 0xfffffff0, },
{ PHY_ID_VSC8530, 0xfffffff0, },
{ PHY_ID_VSC8531, 0xfffffff0, },
{ PHY_ID_VSC8540, 0xfffffff0, },
{ PHY_ID_VSC8541, 0xfffffff0, },
{ PHY_ID_VSC8552, 0xfffffff0, },
{ PHY_ID_VSC856X, 0xfffffff0, },
{ PHY_ID_VSC8572, 0xfffffff0, },
net: phy: mscc: add support for VSC8574 PHY The VSC8574 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports WOL, downshifting and can set the blinking pattern of each of its 4 LEDs, supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, WOL, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8574 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:43 +07:00
{ PHY_ID_VSC8574, 0xfffffff0, },
{ PHY_ID_VSC8575, 0xfffffff0, },
{ PHY_ID_VSC8582, 0xfffffff0, },
net: phy: mscc: add support for VSC8584 PHY The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X and triple-speed copper SFP capable, can communicate with the MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking pattern of each of its 4 LEDs, supports hardware offloading of MACsec and supports SyncE as well as HP Auto-MDIX detection. This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for its 4 LEDs. The VSC8584 has also an internal Intel 8051 microcontroller whose firmware needs to be patched when the PHY is reset. If the 8051's firmware has the expected CRC, its patching can be skipped. The microcontroller can be accessed from any port of the PHY, though the CRC function can only be done through the PHY that is the base PHY of the package (internal address 0) due to a limitation of the firmware. The GPIO register bank is a set of registers that are common to all PHYs in the package. So any modification in any register of this bank affects all PHYs of the package. If the PHYs haven't been reset before booting the Linux kernel and were configured to use interrupts for e.g. link status updates, it is required to clear the interrupts mask register of all PHYs before being able to use interrupts with any PHY. The first PHY of the package that will be init will take care of clearing all PHYs interrupts mask registers. Thus, we need to keep track of the init sequence in the package, if it's already been done or if it's to be done. Most of the init sequence of a PHY of the package is common to all PHYs in the package, thus we use the SMI broadcast feature which enables us to propagate a write in one register of one PHY to all PHYs in the same package. The revA of the VSC8584 PHY (which is not and will not be publicly released) should NOT patch the firmware of the microcontroller or it'll make things worse, the easiest way is just to not support it. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 17:14:42 +07:00
{ PHY_ID_VSC8584, 0xfffffff0, },
{ }
};
MODULE_DEVICE_TABLE(mdio, vsc85xx_tbl);
MODULE_DESCRIPTION("Microsemi VSC85xx PHY driver");
MODULE_AUTHOR("Nagaraju Lakkaraju");
MODULE_LICENSE("Dual MIT/GPL");