WireGuard support for Synology NAS ================================== This package adds WireGuard support for Synology NAS drives. It provides the WireGuard kernel module and the ``wg``/``wg-quick`` commands. Disclaimer ---------- You use everything here at your own risk. I am not responsible if this breaks your NAS. Realistically it should not result in data loss, but it could render your NAS unaccessible if something goes wrong. If you are not comfortable with removing your drives from the NAS and manually recover the data, this might not be for you. FAQ/Known issues ---------------- * The ``Dns = x.x.x.x`` setting is unsupported. If you try it you will get the following message: ``/usr/local/bin/wg-quick: line 31: resolvconf: command not found`` * IPv6 is probably not supported (at least not using ``wg-quick``). Due to the system version of ``iproute2`` `being too old `_. You'll get the error message ``Error: argument "suppress_prefixlength" is wrong: Failed to parse rule type``. * Everything appears to be OK when running ``wg show`` but no traffic is flowing through the tunnel. Apparently there is some kind of race when setting up the interface. The simplest known workaround is to append ``; sleep 5; ip route add 10.0.0.0/16 dev wg0`` to the ``PostUp`` rule. This assumes that your WireGuard IP subnet is ``10.0.x.x``. See `issue #10 `_ for more information. PRs that solve these issues are welcome. Compatibility list ------------------ All models marked *Is working* have been confirmed by users to work. If your model has the same platform as one of the working ones, chances are it will work for you too. DSM 6 ~~~~~ =========== ========== =========== =========================== Model Platform DSM Version Is working? ----------- ---------- ----------- --------------------------- DS1019+ apollolake 6.2 Yes DS114 armada370 *N/A* No (Kernel version too old) DS115j armada370 *N/A* No (Kernel version too old) DS116 armada38x 6.2 Yes DS1511+ x64 6.2 Yes DS1618+ denverton 6.2 Yes DS1817+ avoton 6.2 Yes DS1815+ avoton 6.2 Yes DS213j armada370 *N/A* No (Kernel version too old) DS213j armada370 *N/A* No (Kernel version too old) DS214play armada370 *N/A* No (Kernel version too old) DS214se armada370 *N/A* No (Kernel version too old) DS216+II braswell 6.2 Yes DS216se armada370 *N/A* No (Kernel version too old) DS216Play monaco 6.2 Yes DS218 rtd1296 6.2 Yes DS218+ apollolake 6.2 Yes DS218j armada38x 6.2 Yes DS3617xs broadwell 6.2 Yes DS414slim armada370 *N/A* No (Kernel version too old) DS415+ avoton 6.2 Yes DS418play apollolake 6.2 Yes DS713+ cedarview 6.2 Yes DS716+II braswell 6.2 Yes DS718+ apollolake 6.2 Yes DS916+ braswell 6.2 Yes DS918+ apollolake 6.2 Yes RS214 armada370 *N/A* No (Kernel version too old) RS816 armada38x 6.2 Yes Virtual DSM kvmx64 6.2 Yes =========== ========== =========== =========================== DSM 7 ~~~~~ =========== ========== =========== =========================== Model Platform DSM Version Is working? ----------- ---------- ----------- --------------------------- DS220+ geminilake 7.0 Beta Yes Virtual DSM kvmx64 7.0 Beta Yes =========== ========== =========== =========================== The minimum required kernel version is 3.10. If you have a kernel version lower than that, WireGuard will not work. You can check your kernel version by logging in through SSH and running the ``uname -a`` command. This project is also confirmed to be compatible with other brand NAS stations using `XPEnology `_. ========= ================ ========== =========== =========================== Model Hardware version Platform DSM Version Is working? --------- ---------------- ---------- ----------- --------------------------- HP54NL DS3615xs bromolow 6.2 Yes ========= ================ ========== =========== =========================== Installation ------------ 1. Check the `releases `_ page for SPKs for your platform and DSM version. If there is no SPK you have to compile it yourself using the instruction below. 2. (*Not applicable for DSM from 7.0*) In the Synology DSM web admin UI, open the Package Center and press the Settings button. Set the trust level to Any publisher and press OK to confirm. 3. In the Package Center, press the *Manual install* button and provide the SPK file. Follow the instructions until done. 4. (*Only for DSM from 7.0*) From DSM 7.0, an additional step is required for the WireGuard package to start. This is related to `preventing packages not signed by Synology from running with root privileges `_. When installing the package, uncheck the ``run after installation`` option. After installing the package, `connect to the NAS via SSH `_ and run the ``sudo /var/packages/WireGuard/scripts/start`` command. Now you just need to figure out how to configure WireGuard. There are lots of good guides on how to do that. To put my WireGuard configuration on the NAS, I used SSH and created a ``wg-quick`` configuration in ``/etc/wireguard/wg0.conf``. My configuration looks like this: .. code-block:: [Interface] Address = 10.0.1.1/16 PrivateKey = ListenPort = 16666 PostUp = iptables -A FORWARD -i %i -j ACCEPT; iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE PostDown = iptables -D FORWARD -i %i -j ACCEPT; iptables -t nat -D POSTROUTING -o eth0 -j MASQUERADE [Peer] PublicKey = AllowedIPs = 10.0.1.2/32 Note that you need to modify the rules if your network interface is not ``eth0``. You can check which name your interface has by running ``ip a`` in an SSH session. Adding WireGuard to autostart ----------------------------- DSM since version 7.0 comes with `systemd unit `_ support, while for previous versions you can use the built-in `upstart `_. To standardize the process of adding the WireGuard interface to the autostart, a simple ``wg-autostart`` script has been developed. **Important note:** before adding the interface to the autostart, start it manually by ``sudo wg-quick up wg0`` ensure that it does not cause the system to crash and that you can still access your NAS properly. Otherwise, you may not be able to start the NAS or you may not be able to access the device after a reboot. To add the ``wg0`` interface to the autostart, run the command: .. code-block:: sudo wg-autostart enable wg0 To remove the ``wg0`` interface from the autostart, run the command: .. code-block:: sudo wg-autostart disable wg0 Compiling --------- I've used docker to compile everything, as ``pkgscripts-ng`` clutters the file system quite a bit. First create a docker image by running the following command in this repository: .. code-block:: bash git clone https://github.com/runfalk/synology-wireguard.git cd synology-wireguard/ sudo docker build -t synobuild . Now we can build for any platform and DSM version using: .. code-block:: bash sudo docker run --rm --privileged --env PACKAGE_ARCH= --env DSM_VER= -v $(pwd)/artifacts:/result_spk synobuild You should replace ```` with your NAS's package arch. Using `this table `_ you can figure out which one to use. Note that the package arch must be lowercase. ```` should be replaced with the version of DSM you are compiling for. For the DS218j that I have, the complete command looks like this: .. code-block:: bash sudo docker run --rm --privileged --env PACKAGE_ARCH=armada38x --env DSM_VER=6.2 -v $(pwd)/artifacts:/result_spk synobuild If everything worked you should have a directory called ``artifacts`` that contains your SPK files. Avoiding timeouts when downloading build files ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ It can take a long time to pull development files from SourceForge, including occasional timeouts. To get around this, create a folder locally and map it to the `/toolkit_tarballs` Docker volume using the following command: `-v $(pwd)/:/toolkit_tarballs` to the `docker run` command listed above. This will allow the development files to be stored on your host machine instead of ephemerally in the container. The image will check for existing development files in that folder and will use them instead of pulling them from SourceForge when possible. You can also download the files directly and put them in the folder you created by downloading them from here: https://sourceforge.net/projects/dsgpl/files/toolkit/DSM (e.g. https://sourceforge.net/projects/dsgpl/files/toolkit/DSM6.2) Credits ------- I based a lot of this work on `this guide `_ by Reddit user `akhener `_. However, I had to modify their instructions a lot since my NAS has an ARM CPU which made cross compilation a lot trickier. GitHub user `galaxysd `_ made `a guide `_ on how to enable iptables NAT support.