mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-25 18:55:05 +07:00
6b293258cd
This was too hard to split ... this adds a number of features to the SCOM user interface: - Support for indirect SCOMs - read()/write() interface now handle errors and retries - New ioctl() "raw" interface for use by debuggers Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Reviewed-by: Eddie James <eajames@linux.vnet.ibm.com> Reviewed-by: Alistair Popple <alistair@popple.id.au>
59 lines
2.2 KiB
C
59 lines
2.2 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ WITH Linux-syscall-note */
|
|
#ifndef _UAPI_LINUX_FSI_H
|
|
#define _UAPI_LINUX_FSI_H
|
|
|
|
#include <linux/types.h>
|
|
#include <linux/ioctl.h>
|
|
|
|
/*
|
|
* /dev/scom "raw" ioctl interface
|
|
*
|
|
* The driver supports a high level "read/write" interface which
|
|
* handles retries and converts the status to Linux error codes,
|
|
* however low level tools an debugger need to access the "raw"
|
|
* HW status information and interpret it themselves, so this
|
|
* ioctl interface is also provided for their use case.
|
|
*/
|
|
|
|
/* Structure for SCOM read/write */
|
|
struct scom_access {
|
|
__u64 addr; /* SCOM address, supports indirect */
|
|
__u64 data; /* SCOM data (in for write, out for read) */
|
|
__u64 mask; /* Data mask for writes */
|
|
__u32 intf_errors; /* Interface error flags */
|
|
#define SCOM_INTF_ERR_PARITY 0x00000001 /* Parity error */
|
|
#define SCOM_INTF_ERR_PROTECTION 0x00000002 /* Blocked by secure boot */
|
|
#define SCOM_INTF_ERR_ABORT 0x00000004 /* PIB reset during access */
|
|
#define SCOM_INTF_ERR_UNKNOWN 0x80000000 /* Unknown error */
|
|
/*
|
|
* Note: Any other bit set in intf_errors need to be considered as an
|
|
* error. Future implementations may define new error conditions. The
|
|
* pib_status below is only valid if intf_errors is 0.
|
|
*/
|
|
__u8 pib_status; /* 3-bit PIB status */
|
|
#define SCOM_PIB_SUCCESS 0 /* Access successful */
|
|
#define SCOM_PIB_BLOCKED 1 /* PIB blocked, pls retry */
|
|
#define SCOM_PIB_OFFLINE 2 /* Chiplet offline */
|
|
#define SCOM_PIB_PARTIAL 3 /* Partial good */
|
|
#define SCOM_PIB_BAD_ADDR 4 /* Invalid address */
|
|
#define SCOM_PIB_CLK_ERR 5 /* Clock error */
|
|
#define SCOM_PIB_PARITY_ERR 6 /* Parity error on the PIB bus */
|
|
#define SCOM_PIB_TIMEOUT 7 /* Bus timeout */
|
|
__u8 pad;
|
|
};
|
|
|
|
/* Flags for SCOM check */
|
|
#define SCOM_CHECK_SUPPORTED 0x00000001 /* Interface supported */
|
|
#define SCOM_CHECK_PROTECTED 0x00000002 /* Interface blocked by secure boot */
|
|
|
|
/* Flags for SCOM reset */
|
|
#define SCOM_RESET_INTF 0x00000001 /* Reset interface */
|
|
#define SCOM_RESET_PIB 0x00000002 /* Reset PIB */
|
|
|
|
#define FSI_SCOM_CHECK _IOR('s', 0x00, __u32)
|
|
#define FSI_SCOM_READ _IOWR('s', 0x01, struct scom_access)
|
|
#define FSI_SCOM_WRITE _IOWR('s', 0x02, struct scom_access)
|
|
#define FSI_SCOM_RESET _IOW('s', 0x03, __u32)
|
|
|
|
#endif /* _UAPI_LINUX_FSI_H */
|