linux_dsm_epyc7002/arch/sparc/kernel/leon_smp.c
Greg Kroah-Hartman b24413180f License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-02 11:10:55 +01:00

471 lines
11 KiB
C

// SPDX-License-Identifier: GPL-2.0
/* leon_smp.c: Sparc-Leon SMP support.
*
* based on sun4m_smp.c
* Copyright (C) 1996 David S. Miller (davem@caip.rutgers.edu)
* Copyright (C) 2009 Daniel Hellstrom (daniel@gaisler.com) Aeroflex Gaisler AB
* Copyright (C) 2009 Konrad Eisele (konrad@gaisler.com) Aeroflex Gaisler AB
*/
#include <asm/head.h>
#include <linux/kernel.h>
#include <linux/sched/mm.h>
#include <linux/threads.h>
#include <linux/smp.h>
#include <linux/interrupt.h>
#include <linux/kernel_stat.h>
#include <linux/of.h>
#include <linux/init.h>
#include <linux/spinlock.h>
#include <linux/mm.h>
#include <linux/swap.h>
#include <linux/profile.h>
#include <linux/pm.h>
#include <linux/delay.h>
#include <linux/gfp.h>
#include <linux/cpu.h>
#include <linux/clockchips.h>
#include <asm/cacheflush.h>
#include <asm/tlbflush.h>
#include <asm/ptrace.h>
#include <linux/atomic.h>
#include <asm/irq_regs.h>
#include <asm/traps.h>
#include <asm/delay.h>
#include <asm/irq.h>
#include <asm/page.h>
#include <asm/pgalloc.h>
#include <asm/pgtable.h>
#include <asm/oplib.h>
#include <asm/cpudata.h>
#include <asm/asi.h>
#include <asm/leon.h>
#include <asm/leon_amba.h>
#include <asm/timer.h>
#include "kernel.h"
#include "irq.h"
extern ctxd_t *srmmu_ctx_table_phys;
static int smp_processors_ready;
extern volatile unsigned long cpu_callin_map[NR_CPUS];
extern cpumask_t smp_commenced_mask;
void leon_configure_cache_smp(void);
static void leon_ipi_init(void);
/* IRQ number of LEON IPIs */
int leon_ipi_irq = LEON3_IRQ_IPI_DEFAULT;
static inline unsigned long do_swap(volatile unsigned long *ptr,
unsigned long val)
{
__asm__ __volatile__("swapa [%2] %3, %0\n\t" : "=&r"(val)
: "0"(val), "r"(ptr), "i"(ASI_LEON_DCACHE_MISS)
: "memory");
return val;
}
void leon_cpu_pre_starting(void *arg)
{
leon_configure_cache_smp();
}
void leon_cpu_pre_online(void *arg)
{
int cpuid = hard_smp_processor_id();
/* Allow master to continue. The master will then give us the
* go-ahead by setting the smp_commenced_mask and will wait without
* timeouts until our setup is completed fully (signified by
* our bit being set in the cpu_online_mask).
*/
do_swap(&cpu_callin_map[cpuid], 1);
local_ops->cache_all();
local_ops->tlb_all();
/* Fix idle thread fields. */
__asm__ __volatile__("ld [%0], %%g6\n\t" : : "r"(&current_set[cpuid])
: "memory" /* paranoid */);
/* Attach to the address space of init_task. */
mmgrab(&init_mm);
current->active_mm = &init_mm;
while (!cpumask_test_cpu(cpuid, &smp_commenced_mask))
mb();
}
/*
* Cycle through the processors asking the PROM to start each one.
*/
extern struct linux_prom_registers smp_penguin_ctable;
void leon_configure_cache_smp(void)
{
unsigned long cfg = sparc_leon3_get_dcachecfg();
int me = smp_processor_id();
if (ASI_LEON3_SYSCTRL_CFG_SSIZE(cfg) > 4) {
printk(KERN_INFO "Note: SMP with snooping only works on 4k cache, found %dk(0x%x) on cpu %d, disabling caches\n",
(unsigned int)ASI_LEON3_SYSCTRL_CFG_SSIZE(cfg),
(unsigned int)cfg, (unsigned int)me);
sparc_leon3_disable_cache();
} else {
if (cfg & ASI_LEON3_SYSCTRL_CFG_SNOOPING) {
sparc_leon3_enable_snooping();
} else {
printk(KERN_INFO "Note: You have to enable snooping in the vhdl model cpu %d, disabling caches\n",
me);
sparc_leon3_disable_cache();
}
}
local_ops->cache_all();
local_ops->tlb_all();
}
static void leon_smp_setbroadcast(unsigned int mask)
{
int broadcast =
((LEON3_BYPASS_LOAD_PA(&(leon3_irqctrl_regs->mpstatus)) >>
LEON3_IRQMPSTATUS_BROADCAST) & 1);
if (!broadcast) {
prom_printf("######## !!!! The irqmp-ctrl must have broadcast enabled, smp wont work !!!!! ####### nr cpus: %d\n",
leon_smp_nrcpus());
if (leon_smp_nrcpus() > 1) {
BUG();
} else {
prom_printf("continue anyway\n");
return;
}
}
LEON_BYPASS_STORE_PA(&(leon3_irqctrl_regs->mpbroadcast), mask);
}
int leon_smp_nrcpus(void)
{
int nrcpu =
((LEON3_BYPASS_LOAD_PA(&(leon3_irqctrl_regs->mpstatus)) >>
LEON3_IRQMPSTATUS_CPUNR) & 0xf) + 1;
return nrcpu;
}
void __init leon_boot_cpus(void)
{
int nrcpu = leon_smp_nrcpus();
int me = smp_processor_id();
/* Setup IPI */
leon_ipi_init();
printk(KERN_INFO "%d:(%d:%d) cpus mpirq at 0x%x\n", (unsigned int)me,
(unsigned int)nrcpu, (unsigned int)NR_CPUS,
(unsigned int)&(leon3_irqctrl_regs->mpstatus));
leon_enable_irq_cpu(LEON3_IRQ_CROSS_CALL, me);
leon_enable_irq_cpu(LEON3_IRQ_TICKER, me);
leon_enable_irq_cpu(leon_ipi_irq, me);
leon_smp_setbroadcast(1 << LEON3_IRQ_TICKER);
leon_configure_cache_smp();
local_ops->cache_all();
}
int leon_boot_one_cpu(int i, struct task_struct *idle)
{
int timeout;
current_set[i] = task_thread_info(idle);
/* See trampoline.S:leon_smp_cpu_startup for details...
* Initialize the contexts table
* Since the call to prom_startcpu() trashes the structure,
* we need to re-initialize it for each cpu
*/
smp_penguin_ctable.which_io = 0;
smp_penguin_ctable.phys_addr = (unsigned int)srmmu_ctx_table_phys;
smp_penguin_ctable.reg_size = 0;
/* whirrr, whirrr, whirrrrrrrrr... */
printk(KERN_INFO "Starting CPU %d : (irqmp: 0x%x)\n", (unsigned int)i,
(unsigned int)&leon3_irqctrl_regs->mpstatus);
local_ops->cache_all();
/* Make sure all IRQs are of from the start for this new CPU */
LEON_BYPASS_STORE_PA(&leon3_irqctrl_regs->mask[i], 0);
/* Wake one CPU */
LEON_BYPASS_STORE_PA(&(leon3_irqctrl_regs->mpstatus), 1 << i);
/* wheee... it's going... */
for (timeout = 0; timeout < 10000; timeout++) {
if (cpu_callin_map[i])
break;
udelay(200);
}
printk(KERN_INFO "Started CPU %d\n", (unsigned int)i);
if (!(cpu_callin_map[i])) {
printk(KERN_ERR "Processor %d is stuck.\n", i);
return -ENODEV;
} else {
leon_enable_irq_cpu(LEON3_IRQ_CROSS_CALL, i);
leon_enable_irq_cpu(LEON3_IRQ_TICKER, i);
leon_enable_irq_cpu(leon_ipi_irq, i);
}
local_ops->cache_all();
return 0;
}
void __init leon_smp_done(void)
{
int i, first;
int *prev;
/* setup cpu list for irq rotation */
first = 0;
prev = &first;
for (i = 0; i < NR_CPUS; i++) {
if (cpu_online(i)) {
*prev = i;
prev = &cpu_data(i).next;
}
}
*prev = first;
local_ops->cache_all();
/* Free unneeded trap tables */
if (!cpu_present(1)) {
free_reserved_page(virt_to_page(&trapbase_cpu1));
}
if (!cpu_present(2)) {
free_reserved_page(virt_to_page(&trapbase_cpu2));
}
if (!cpu_present(3)) {
free_reserved_page(virt_to_page(&trapbase_cpu3));
}
/* Ok, they are spinning and ready to go. */
smp_processors_ready = 1;
}
struct leon_ipi_work {
int single;
int msk;
int resched;
};
static DEFINE_PER_CPU_SHARED_ALIGNED(struct leon_ipi_work, leon_ipi_work);
/* Initialize IPIs on the LEON, in order to save IRQ resources only one IRQ
* is used for all three types of IPIs.
*/
static void __init leon_ipi_init(void)
{
int cpu, len;
struct leon_ipi_work *work;
struct property *pp;
struct device_node *rootnp;
struct tt_entry *trap_table;
unsigned long flags;
/* Find IPI IRQ or stick with default value */
rootnp = of_find_node_by_path("/ambapp0");
if (rootnp) {
pp = of_find_property(rootnp, "ipi_num", &len);
if (pp && (*(int *)pp->value))
leon_ipi_irq = *(int *)pp->value;
}
printk(KERN_INFO "leon: SMP IPIs at IRQ %d\n", leon_ipi_irq);
/* Adjust so that we jump directly to smpleon_ipi */
local_irq_save(flags);
trap_table = &sparc_ttable[SP_TRAP_IRQ1 + (leon_ipi_irq - 1)];
trap_table->inst_three += smpleon_ipi - real_irq_entry;
local_ops->cache_all();
local_irq_restore(flags);
for_each_possible_cpu(cpu) {
work = &per_cpu(leon_ipi_work, cpu);
work->single = work->msk = work->resched = 0;
}
}
static void leon_send_ipi(int cpu, int level)
{
unsigned long mask;
mask = leon_get_irqmask(level);
LEON3_BYPASS_STORE_PA(&leon3_irqctrl_regs->force[cpu], mask);
}
static void leon_ipi_single(int cpu)
{
struct leon_ipi_work *work = &per_cpu(leon_ipi_work, cpu);
/* Mark work */
work->single = 1;
/* Generate IRQ on the CPU */
leon_send_ipi(cpu, leon_ipi_irq);
}
static void leon_ipi_mask_one(int cpu)
{
struct leon_ipi_work *work = &per_cpu(leon_ipi_work, cpu);
/* Mark work */
work->msk = 1;
/* Generate IRQ on the CPU */
leon_send_ipi(cpu, leon_ipi_irq);
}
static void leon_ipi_resched(int cpu)
{
struct leon_ipi_work *work = &per_cpu(leon_ipi_work, cpu);
/* Mark work */
work->resched = 1;
/* Generate IRQ on the CPU (any IRQ will cause resched) */
leon_send_ipi(cpu, leon_ipi_irq);
}
void leonsmp_ipi_interrupt(void)
{
struct leon_ipi_work *work = this_cpu_ptr(&leon_ipi_work);
if (work->single) {
work->single = 0;
smp_call_function_single_interrupt();
}
if (work->msk) {
work->msk = 0;
smp_call_function_interrupt();
}
if (work->resched) {
work->resched = 0;
smp_resched_interrupt();
}
}
static struct smp_funcall {
smpfunc_t func;
unsigned long arg1;
unsigned long arg2;
unsigned long arg3;
unsigned long arg4;
unsigned long arg5;
unsigned long processors_in[NR_CPUS]; /* Set when ipi entered. */
unsigned long processors_out[NR_CPUS]; /* Set when ipi exited. */
} ccall_info __attribute__((aligned(8)));
static DEFINE_SPINLOCK(cross_call_lock);
/* Cross calls must be serialized, at least currently. */
static void leon_cross_call(smpfunc_t func, cpumask_t mask, unsigned long arg1,
unsigned long arg2, unsigned long arg3,
unsigned long arg4)
{
if (smp_processors_ready) {
register int high = NR_CPUS - 1;
unsigned long flags;
spin_lock_irqsave(&cross_call_lock, flags);
{
/* If you make changes here, make sure gcc generates proper code... */
register smpfunc_t f asm("i0") = func;
register unsigned long a1 asm("i1") = arg1;
register unsigned long a2 asm("i2") = arg2;
register unsigned long a3 asm("i3") = arg3;
register unsigned long a4 asm("i4") = arg4;
register unsigned long a5 asm("i5") = 0;
__asm__ __volatile__("std %0, [%6]\n\t"
"std %2, [%6 + 8]\n\t"
"std %4, [%6 + 16]\n\t" : :
"r"(f), "r"(a1), "r"(a2), "r"(a3),
"r"(a4), "r"(a5),
"r"(&ccall_info.func));
}
/* Init receive/complete mapping, plus fire the IPI's off. */
{
register int i;
cpumask_clear_cpu(smp_processor_id(), &mask);
cpumask_and(&mask, cpu_online_mask, &mask);
for (i = 0; i <= high; i++) {
if (cpumask_test_cpu(i, &mask)) {
ccall_info.processors_in[i] = 0;
ccall_info.processors_out[i] = 0;
leon_send_ipi(i, LEON3_IRQ_CROSS_CALL);
}
}
}
{
register int i;
i = 0;
do {
if (!cpumask_test_cpu(i, &mask))
continue;
while (!ccall_info.processors_in[i])
barrier();
} while (++i <= high);
i = 0;
do {
if (!cpumask_test_cpu(i, &mask))
continue;
while (!ccall_info.processors_out[i])
barrier();
} while (++i <= high);
}
spin_unlock_irqrestore(&cross_call_lock, flags);
}
}
/* Running cross calls. */
void leon_cross_call_irq(void)
{
int i = smp_processor_id();
ccall_info.processors_in[i] = 1;
ccall_info.func(ccall_info.arg1, ccall_info.arg2, ccall_info.arg3,
ccall_info.arg4, ccall_info.arg5);
ccall_info.processors_out[i] = 1;
}
static const struct sparc32_ipi_ops leon_ipi_ops = {
.cross_call = leon_cross_call,
.resched = leon_ipi_resched,
.single = leon_ipi_single,
.mask_one = leon_ipi_mask_one,
};
void __init leon_init_smp(void)
{
/* Patch ipi15 trap table */
t_nmi[1] = t_nmi[1] + (linux_trap_ipi15_leon - linux_trap_ipi15_sun4m);
sparc32_ipi_ops = &leon_ipi_ops;
}