mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-21 05:49:10 +07:00
1004a2977b
Use the new EBI/NAND bindings to declare NAND chips and remove old NAND nodes along the way. Note that we keep using old bindings in at91rm9200.dtsi because this SoC is not supported by the EBI driver. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Tested-by: Peter Rosin <peda@axentia.se> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
174 lines
3.0 KiB
Plaintext
174 lines
3.0 KiB
Plaintext
/*
|
|
* pm9g45.dts - Device Tree file for Ronetix pm9g45 board
|
|
*
|
|
* Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
*
|
|
* Licensed under GPLv2.
|
|
*/
|
|
/dts-v1/;
|
|
#include "at91sam9g45.dtsi"
|
|
|
|
/ {
|
|
model = "Ronetix pm9g45";
|
|
compatible = "ronetix,pm9g45", "atmel,at91sam9g45", "atmel,at91sam9";
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200";
|
|
};
|
|
|
|
memory {
|
|
reg = <0x70000000 0x8000000>;
|
|
};
|
|
|
|
clocks {
|
|
slow_xtal {
|
|
clock-frequency = <32768>;
|
|
};
|
|
|
|
main_xtal {
|
|
clock-frequency = <12000000>;
|
|
};
|
|
};
|
|
|
|
ahb {
|
|
apb {
|
|
dbgu: serial@ffffee00 {
|
|
status = "okay";
|
|
};
|
|
|
|
pinctrl@fffff200 {
|
|
nand {
|
|
pinctrl_nand_rb: nand-rb-0 {
|
|
atmel,pins =
|
|
<AT91_PIOD 3 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
|
|
};
|
|
};
|
|
|
|
mmc {
|
|
pinctrl_board_mmc: mmc0-board {
|
|
atmel,pins =
|
|
<AT91_PIOD 6 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD6 gpio CD pin pull_up and deglitch */
|
|
};
|
|
};
|
|
};
|
|
|
|
mmc0: mmc@fff80000 {
|
|
pinctrl-0 = <
|
|
&pinctrl_board_mmc
|
|
&pinctrl_mmc0_slot0_clk_cmd_dat0
|
|
&pinctrl_mmc0_slot0_dat1_3>;
|
|
status = "okay";
|
|
slot@0 {
|
|
reg = <0>;
|
|
bus-width = <4>;
|
|
cd-gpios = <&pioD 6 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
macb0: ethernet@fffbc000 {
|
|
phy-mode = "rmii";
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
ebi: ebi@10000000 {
|
|
status = "okay";
|
|
|
|
nand_controller: nand-controller {
|
|
status = "okay";
|
|
pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb>;
|
|
pinctrl-names = "default";
|
|
|
|
nand@3 {
|
|
reg = <0x3 0x0 0x800000>;
|
|
rb-gpios = <&pioD 3 GPIO_ACTIVE_HIGH>;
|
|
cs-gpios = <&pioC 14 GPIO_ACTIVE_HIGH>;
|
|
nand-bus-width = <8>;
|
|
nand-ecc-mode = "soft";
|
|
nand-on-flash-bbt;
|
|
label = "atmel_nand";
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
at91bootstrap@0 {
|
|
label = "at91bootstrap";
|
|
reg = <0x0 0x20000>;
|
|
};
|
|
|
|
barebox@20000 {
|
|
label = "barebox";
|
|
reg = <0x20000 0x40000>;
|
|
};
|
|
|
|
bareboxenv@60000 {
|
|
label = "bareboxenv";
|
|
reg = <0x60000 0x1A0000>;
|
|
};
|
|
|
|
kernel@200000 {
|
|
label = "bareboxenv2";
|
|
reg = <0x200000 0x300000>;
|
|
};
|
|
|
|
kernel@500000 {
|
|
label = "root";
|
|
reg = <0x500000 0x400000>;
|
|
};
|
|
|
|
data@900000 {
|
|
label = "data";
|
|
reg = <0x900000 0x8340000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
usb0: ohci@00700000 {
|
|
status = "okay";
|
|
num-ports = <2>;
|
|
};
|
|
|
|
usb1: ehci@00800000 {
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led0 {
|
|
label = "led0";
|
|
gpios = <&pioD 0 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "nand-disk";
|
|
};
|
|
|
|
led1 {
|
|
label = "led1";
|
|
gpios = <&pioD 31 GPIO_ACTIVE_HIGH>;
|
|
linux,default-trigger = "heartbeat";
|
|
};
|
|
};
|
|
|
|
gpio_keys {
|
|
compatible = "gpio-keys";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
right {
|
|
label = "SW4";
|
|
gpios = <&pioE 7 GPIO_ACTIVE_LOW>;
|
|
linux,code = <106>;
|
|
};
|
|
|
|
up {
|
|
label = "SW3";
|
|
gpios = <&pioE 8 GPIO_ACTIVE_LOW>;
|
|
linux,code = <103>;
|
|
};
|
|
};
|
|
};
|