mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-27 15:35:06 +07:00
7ed98dddb7
The OCC is a device embedded on a POWER processor that collects and aggregates sensor data from the processor and system. The OCC can provide the raw sensor data as well as perform thermal and power management on the system. This driver provides an atomic communications channel between a service processor (e.g. a BMC) and the OCC. The driver is dependent on the FSI SBEFIFO driver to get hardware access through the SBE to the OCC SRAM. Commands are issued to the SBE to send or fetch data to the SRAM. Signed-off-by: Eddie James <eajames@linux.ibm.com> Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
79 lines
2.4 KiB
Plaintext
79 lines
2.4 KiB
Plaintext
#
|
|
# FSI subsystem
|
|
#
|
|
|
|
menuconfig FSI
|
|
tristate "FSI support"
|
|
depends on OF
|
|
select CRC4
|
|
---help---
|
|
FSI - the FRU Support Interface - is a simple bus for low-level
|
|
access to POWER-based hardware.
|
|
|
|
if FSI
|
|
|
|
config FSI_NEW_DEV_NODE
|
|
bool "Create '/dev/fsi' directory for char devices"
|
|
default n
|
|
---help---
|
|
This option causes char devices created for FSI devices to be
|
|
located under a common /dev/fsi/ directory. Set to N unless your
|
|
userspace has been updated to handle the new location.
|
|
|
|
Additionally, it also causes the char device names to be offset
|
|
by one so that chip 0 will have /dev/scom1 and chip1 /dev/scom2
|
|
to match old userspace expectations.
|
|
|
|
New userspace will use udev rules to generate predictable access
|
|
symlinks in /dev/fsi/by-path when this option is enabled.
|
|
|
|
config FSI_MASTER_GPIO
|
|
tristate "GPIO-based FSI master"
|
|
depends on GPIOLIB
|
|
select CRC4
|
|
---help---
|
|
This option enables a FSI master driver using GPIO lines.
|
|
|
|
config FSI_MASTER_HUB
|
|
tristate "FSI hub master"
|
|
---help---
|
|
This option enables a FSI hub master driver. Hub is a type of FSI
|
|
master that is connected to the upstream master via a slave. Hubs
|
|
allow chaining of FSI links to an arbitrary depth. This allows for
|
|
a high target device fanout.
|
|
|
|
config FSI_MASTER_AST_CF
|
|
tristate "FSI master based on Aspeed ColdFire coprocessor"
|
|
depends on GPIOLIB
|
|
depends on GPIO_ASPEED
|
|
select GENERIC_ALLOCATOR
|
|
---help---
|
|
This option enables a FSI master using the AST2400 and AST2500 GPIO
|
|
lines driven by the internal ColdFire coprocessor. This requires
|
|
the corresponding machine specific ColdFire firmware to be available.
|
|
|
|
config FSI_SCOM
|
|
tristate "SCOM FSI client device driver"
|
|
---help---
|
|
This option enables an FSI based SCOM device driver.
|
|
|
|
config FSI_SBEFIFO
|
|
tristate "SBEFIFO FSI client device driver"
|
|
depends on OF_ADDRESS
|
|
---help---
|
|
This option enables an FSI based SBEFIFO device driver. The SBEFIFO is
|
|
a pipe-like FSI device for communicating with the self boot engine
|
|
(SBE) on POWER processors.
|
|
|
|
config FSI_OCC
|
|
tristate "OCC SBEFIFO client device driver"
|
|
depends on FSI_SBEFIFO
|
|
---help---
|
|
This option enables an SBEFIFO based On-Chip Controller (OCC) device
|
|
driver. The OCC is a device embedded on a POWER processor that collects
|
|
and aggregates sensor data from the processor and system. The OCC can
|
|
provide the raw sensor data as well as perform thermal and power
|
|
management on the system.
|
|
|
|
endif
|