mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-22 12:27:19 +07:00
aecc313490
SolidRun Clearfog GTR L8 and S4 SBCs are based on Armada 385. They features 8 (L8) or 4 (S4) switched Ethernet ports, 1 1Gb Ethernet port, 1 directly connected SFP port, 1 SFP port behind the switch (not currently described in DT), 3 mini-PCIe slots, eMMC, SPI flash, USB3 port. https://developer.solid-run.com/products/clearfog-gtr-a385/ Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
451 lines
9.2 KiB
Plaintext
451 lines
9.2 KiB
Plaintext
// SPDX-License-Identifier: (GPL-2.0 OR MIT)
|
|
/*
|
|
* Device Tree file for Clearfog GTR machines rev 1.0 (88F6825)
|
|
*
|
|
* Rabeeh Khoury <rabeeh@solid-run.com>, based on Russell King clearfog work
|
|
*/
|
|
|
|
/*
|
|
SERDES mapping -
|
|
0. SATA1 on CON18, or optionally mini PCIe CON3 - PCIe0
|
|
1. 6141 switch (2.5Gbps capable)
|
|
2. SATA0 on CON17, or optionally mini PCIe CON4 - PCIe1
|
|
3. USB 3.0 Host
|
|
4. mini PCIe CON2 - PCIe2
|
|
5. SFP connector, or optionally SGMII Ethernet 1512 PHY
|
|
|
|
USB 2.0 mapping -
|
|
0. USB 2.0 - 0 USB pins header CON12
|
|
1. USB 2.0 - 1 mini PCIe CON2
|
|
2. USB 2.0 - 2 to USB 3.0 connector (used with SERDES #3)
|
|
|
|
Pin mapping -
|
|
0,1 - console UART
|
|
2,3 - I2C0 - connected to I2C EEPROM, two temperature sensors,
|
|
front panel and PSE controller
|
|
4,5 - MDC/MDIO
|
|
6..17 - RGMII
|
|
18 - Topaz switch reset (active low)
|
|
19 - 1512 phy reset
|
|
20 - 1512 phy reset (eth2, optional)
|
|
21,28,37,38,39,40 - SD0
|
|
22 - USB 3.0 current limiter enable (active high)
|
|
24 - SFP TX fault (input active high)
|
|
25 - SFP present (input active low)
|
|
26,27 - I2C1 - connected to SFP
|
|
29 - Fan PWM
|
|
30 - CON4 mini PCIe wifi disable
|
|
31 - CON3 mini PCIe wifi disable
|
|
32 - Fuse programming power toggle (1.8v)
|
|
33 - CON4 mini PCIe reset
|
|
34 - CON2 mini PCIe wifi disable
|
|
35 - CON3 mini PCIe reset
|
|
36 - Rear button (GPIO active low)
|
|
41 - CON1 front panel connector
|
|
42 - Front LED1, or front panel CON1
|
|
43 - Micron L-PBGA 24 ball SPI (1Gb) CS, or TPM SPI CS
|
|
44 - CON2 mini PCIe reset
|
|
45 - TPM PIRQ signal, or front panel CON1
|
|
46 - SFP TX disable
|
|
47 - Control isolation of boot sensitive SAR signals
|
|
48 - PSE reset
|
|
49 - PSE OSS signal
|
|
50 - PSE interrupt
|
|
52 - Front LED2, or front panel
|
|
53 - Front button
|
|
54 - SFP LOS (input active high)
|
|
55 - Fan sense
|
|
56(mosi),57(clk),58(miso) - SPI interface - 32Mb SPI, 1Gb SPI and TPM
|
|
59 - SPI 32Mb W25Q32BVZPIG CS0 chip select (bootable)
|
|
*/
|
|
|
|
/dts-v1/;
|
|
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/leds/common.h>
|
|
#include "armada-385.dtsi"
|
|
|
|
/ {
|
|
compatible = "marvell,armada385", "marvell,armada380";
|
|
|
|
aliases {
|
|
/* So that mvebu u-boot can update the MAC addresses */
|
|
ethernet1 = ð0;
|
|
ethernet2 = ð1;
|
|
ethernet3 = ð2;
|
|
i2c0 = &i2c0;
|
|
i2c1 = &i2c1;
|
|
};
|
|
|
|
chosen {
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
|
|
memory {
|
|
device_type = "memory";
|
|
reg = <0x00000000 0x10000000>; /* 256 MB */
|
|
};
|
|
|
|
reg_3p3v: regulator-3p3v {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "3P3V";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-always-on;
|
|
};
|
|
|
|
reg_5p0v: regulator-5p0v {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "5P0V";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
regulator-always-on;
|
|
};
|
|
|
|
v_usb3_con: regulator-v-usb3-con {
|
|
compatible = "regulator-fixed";
|
|
gpio = <&gpio0 22 GPIO_ACTIVE_LOW>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&cf_gtr_usb3_con_vbus>;
|
|
regulator-max-microvolt = <5000000>;
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-name = "v_usb3_con";
|
|
vin-supply = <®_5p0v>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
|
|
soc {
|
|
ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
|
|
MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
|
|
MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
|
|
MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000
|
|
MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>;
|
|
|
|
internal-regs {
|
|
|
|
rtc@a3800 {
|
|
status = "okay";
|
|
};
|
|
|
|
i2c@11000 { /* ROM, temp sensor and front panel */
|
|
pinctrl-0 = <&i2c0_pins>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
};
|
|
|
|
i2c@11100 { /* SFP (CON5/CON6) */
|
|
pinctrl-0 = <&cf_gtr_i2c1_pins>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
};
|
|
|
|
pinctrl@18000 {
|
|
cf_gtr_switch_reset_pins: cf-gtr-switch-reset-pins {
|
|
marvell,pins = "mpp18";
|
|
marvell,function = "gpio";
|
|
};
|
|
|
|
cf_gtr_usb3_con_vbus: cf-gtr-usb3-con-vbus {
|
|
marvell,pins = "mpp22";
|
|
marvell,function = "gpio";
|
|
};
|
|
|
|
cf_gtr_fan_pwm: cf-gtr-fan-pwm {
|
|
marvell,pins = "mpp23";
|
|
marvell,function = "gpio";
|
|
};
|
|
|
|
cf_gtr_i2c1_pins: i2c1-pins {
|
|
/* SFP */
|
|
marvell,pins = "mpp26", "mpp27";
|
|
marvell,function = "i2c1";
|
|
};
|
|
|
|
cf_gtr_sdhci_pins: cf-gtr-sdhci-pins {
|
|
marvell,pins = "mpp21", "mpp28",
|
|
"mpp37", "mpp38",
|
|
"mpp39", "mpp40";
|
|
marvell,function = "sd0";
|
|
};
|
|
|
|
cf_gtr_isolation_pins: cf-gtr-isolation-pins {
|
|
marvell,pins = "mpp47";
|
|
marvell,function = "gpio";
|
|
};
|
|
|
|
cf_gtr_poe_reset_pins: cf-gtr-poe-reset-pins {
|
|
marvell,pins = "mpp48";
|
|
marvell,function = "gpio";
|
|
};
|
|
|
|
cf_gtr_spi1_cs_pins: spi1-cs-pins {
|
|
marvell,pins = "mpp59";
|
|
marvell,function = "spi1";
|
|
};
|
|
|
|
cf_gtr_front_button_pins: cf-gtr-front-button-pins {
|
|
marvell,pins = "mpp53";
|
|
marvell,function = "gpio";
|
|
};
|
|
|
|
cf_gtr_rear_button_pins: cf-gtr-rear-button-pins {
|
|
marvell,pins = "mpp36";
|
|
marvell,function = "gpio";
|
|
};
|
|
};
|
|
|
|
sdhci@d8000 {
|
|
bus-width = <4>;
|
|
no-1-8-v;
|
|
non-removable;
|
|
pinctrl-0 = <&cf_gtr_sdhci_pins>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
vmmc = <®_3p3v>;
|
|
wp-inverted;
|
|
};
|
|
|
|
usb@58000 {
|
|
status = "okay";
|
|
};
|
|
|
|
usb3@f0000 {
|
|
status = "okay";
|
|
};
|
|
|
|
usb3@f8000 {
|
|
vbus-supply = <&v_usb3_con>;
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
pcie {
|
|
status = "okay";
|
|
/*
|
|
* The PCIe units are accessible through
|
|
* the mini-PCIe connectors on the board.
|
|
*/
|
|
pcie@1,0 {
|
|
reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
|
|
status = "okay";
|
|
};
|
|
|
|
pcie@2,0 {
|
|
reset-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
|
|
status = "okay";
|
|
};
|
|
|
|
pcie@3,0 {
|
|
reset-gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
|
|
status = "okay";
|
|
};
|
|
};
|
|
};
|
|
|
|
sfp0: sfp {
|
|
compatible = "sff,sfp";
|
|
i2c-bus = <&i2c1>;
|
|
los-gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
|
|
mod-def0-gpio = <&gpio0 25 GPIO_ACTIVE_LOW>;
|
|
tx-disable-gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
gpio-keys {
|
|
compatible = "gpio-keys";
|
|
pinctrl-0 = <&cf_gtr_rear_button_pins &cf_gtr_front_button_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
button_0 {
|
|
label = "Rear Button";
|
|
gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
|
|
linux,can-disable;
|
|
linux,code = <BTN_0>;
|
|
};
|
|
|
|
button_1 {
|
|
label = "Front Button";
|
|
gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
|
|
linux,can-disable;
|
|
linux,code = <BTN_1>;
|
|
};
|
|
};
|
|
|
|
gpio-leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led1 {
|
|
function = LED_FUNCTION_CPU;
|
|
color = <LED_COLOR_ID_GREEN>;
|
|
gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
led2 {
|
|
function = LED_FUNCTION_HEARTBEAT;
|
|
color = <LED_COLOR_ID_GREEN>;
|
|
gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&bm {
|
|
status = "okay";
|
|
};
|
|
|
|
&bm_bppi {
|
|
status = "okay";
|
|
};
|
|
|
|
ð0 {
|
|
/* ethernet@70000 */
|
|
pinctrl-0 = <&ge0_rgmii_pins>;
|
|
pinctrl-names = "default";
|
|
phy = <&phy_dedicated>;
|
|
phy-mode = "rgmii-id";
|
|
buffer-manager = <&bm>;
|
|
bm,pool-long = <0>;
|
|
bm,pool-short = <1>;
|
|
status = "okay";
|
|
};
|
|
|
|
ð1 {
|
|
/* ethernet@30000 */
|
|
bm,pool-long = <2>;
|
|
bm,pool-short = <1>;
|
|
buffer-manager = <&bm>;
|
|
phys = <&comphy1 1>;
|
|
phy-mode = "2500base-x";
|
|
status = "okay";
|
|
|
|
fixed-link {
|
|
speed = <2500>;
|
|
full-duplex;
|
|
};
|
|
};
|
|
|
|
ð2 {
|
|
/* ethernet@34000 */
|
|
bm,pool-long = <3>;
|
|
bm,pool-short = <1>;
|
|
buffer-manager = <&bm>;
|
|
managed = "in-band-status";
|
|
phys = <&comphy5 1>;
|
|
phy-mode = "sgmii";
|
|
sfp = <&sfp0>;
|
|
status = "okay";
|
|
};
|
|
|
|
&mdio {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&mdio_pins>;
|
|
status = "okay";
|
|
|
|
phy_dedicated: ethernet-phy@0 {
|
|
/*
|
|
* Annoyingly, the marvell phy driver configures the LED
|
|
* register, rather than preserving reset-loaded setting.
|
|
* We undo that rubbish here.
|
|
*/
|
|
marvell,reg-init = <3 16 0 0x1017>;
|
|
reg = <0>;
|
|
};
|
|
};
|
|
|
|
&uart0 {
|
|
pinctrl-0 = <&uart0_pins>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
};
|
|
|
|
&spi1 {
|
|
/*
|
|
* CS0: W25Q32 flash
|
|
*/
|
|
pinctrl-0 = <&spi1_pins &cf_gtr_spi1_cs_pins>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
|
|
spi-flash@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
compatible = "w25q32", "jedec,spi-nor";
|
|
reg = <0>; /* Chip select 0 */
|
|
spi-max-frequency = <3000000>;
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
&i2c0 {
|
|
pinctrl-0 = <&i2c0_pins>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
|
|
/* U26 temperature sensor placed near SoC */
|
|
temp1: nct75@4c {
|
|
compatible = "lm75";
|
|
reg = <0x4c>;
|
|
};
|
|
|
|
/* U27 temperature sensor placed near RTC battery */
|
|
temp2: nct75@4d {
|
|
compatible = "lm75";
|
|
reg = <0x4d>;
|
|
};
|
|
|
|
/* 2Kb eeprom */
|
|
eeprom@53 {
|
|
compatible = "atmel,24c02";
|
|
reg = <0x53>;
|
|
};
|
|
};
|
|
|
|
&ahci0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&ahci1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpio0 {
|
|
pinctrl-0 = <&cf_gtr_fan_pwm>;
|
|
pinctrl-names = "default";
|
|
|
|
wifi-disable {
|
|
gpio-hog;
|
|
gpios = <30 GPIO_ACTIVE_LOW>, <31 GPIO_ACTIVE_LOW>;
|
|
output-low;
|
|
line-name = "wifi-disable";
|
|
};
|
|
};
|
|
|
|
&gpio1 {
|
|
pinctrl-0 = <&cf_gtr_isolation_pins &cf_gtr_poe_reset_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
lte-disable {
|
|
gpio-hog;
|
|
gpios = <2 GPIO_ACTIVE_LOW>;
|
|
output-low;
|
|
line-name = "lte-disable";
|
|
};
|
|
|
|
/*
|
|
* This signal, when asserted, isolates Armada 38x sample at reset pins
|
|
* from control of external devices. Should be de-asserted after reset.
|
|
*/
|
|
sar-isolation {
|
|
gpio-hog;
|
|
gpios = <15 GPIO_ACTIVE_LOW>;
|
|
output-low;
|
|
line-name = "sar-isolation";
|
|
};
|
|
|
|
poe-reset {
|
|
gpio-hog;
|
|
gpios = <16 GPIO_ACTIVE_LOW>;
|
|
output-low;
|
|
line-name = "poe-reset";
|
|
};
|
|
};
|