mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-23 09:09:36 +07:00
00e3ff8b98
The devicetree specification recommends using generic node names. Some Zii dts files already follow such recommendation, but some don't, so use generic node names for consistency among the Zii dts files. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
341 lines
6.3 KiB
Plaintext
341 lines
6.3 KiB
Plaintext
// SPDX-License-Identifier: (GPL-2.0 OR MIT)
|
|
|
|
/*
|
|
* Copyright (C) 2018 Zodiac Inflight Innovations
|
|
*/
|
|
|
|
/dts-v1/;
|
|
#include "vf610.dtsi"
|
|
|
|
/ {
|
|
model = "ZII VF610 CFU1 Board";
|
|
compatible = "zii,vf610cfu1", "zii,vf610dev", "fsl,vf610";
|
|
|
|
chosen {
|
|
stdout-path = &uart0;
|
|
};
|
|
|
|
memory@80000000 {
|
|
device_type = "memory";
|
|
reg = <0x80000000 0x20000000>;
|
|
};
|
|
|
|
gpio-leds {
|
|
compatible = "gpio-leds";
|
|
pinctrl-0 = <&pinctrl_leds_debug>;
|
|
pinctrl-names = "default";
|
|
|
|
led-debug {
|
|
label = "zii:green:debug1";
|
|
gpios = <&gpio2 18 GPIO_ACTIVE_HIGH>;
|
|
linux,default-trigger = "heartbeat";
|
|
};
|
|
|
|
led-fail {
|
|
label = "zii:red:fail";
|
|
gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
|
|
default-state = "off";
|
|
};
|
|
|
|
led-status {
|
|
label = "zii:green:status";
|
|
gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
|
|
default-state = "off";
|
|
};
|
|
|
|
led-debug-a {
|
|
label = "zii:green:debug_a";
|
|
gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
|
|
default-state = "off";
|
|
};
|
|
|
|
led-debug-b {
|
|
label = "zii:green:debug_b";
|
|
gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>;
|
|
default-state = "off";
|
|
};
|
|
};
|
|
|
|
reg_vcc_3v3_mcu: regulator-vcc-3v3-mcu {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "vcc_3v3_mcu";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
};
|
|
|
|
sff: sfp {
|
|
compatible = "sff,sff";
|
|
pinctrl-0 = <&pinctrl_optical>;
|
|
pinctrl-names = "default";
|
|
i2c-bus = <&i2c0>;
|
|
los-gpio = <&gpio4 4 GPIO_ACTIVE_HIGH>;
|
|
tx-disable-gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
&adc0 {
|
|
vref-supply = <®_vcc_3v3_mcu>;
|
|
status = "okay";
|
|
};
|
|
|
|
&adc1 {
|
|
vref-supply = <®_vcc_3v3_mcu>;
|
|
status = "okay";
|
|
};
|
|
|
|
&dspi1 {
|
|
bus-num = <1>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_dspi1>;
|
|
/*
|
|
* Some CFU1s come with SPI-NOR chip DNPed, so we leave this
|
|
* node disabled by default and rely on bootloader to enable
|
|
* it when appropriate.
|
|
*/
|
|
status = "disabled";
|
|
|
|
flash@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "m25p128", "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <50000000>;
|
|
|
|
partition@0 {
|
|
label = "m25p128-0";
|
|
reg = <0x0 0x01000000>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&edma0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&edma1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&esdhc0 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_esdhc0>;
|
|
bus-width = <8>;
|
|
non-removable;
|
|
no-1-8-v;
|
|
keep-power-in-suspend;
|
|
no-sdio;
|
|
no-sd;
|
|
status = "okay";
|
|
};
|
|
|
|
&esdhc1 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_esdhc1>;
|
|
bus-width = <4>;
|
|
no-sdio;
|
|
status = "okay";
|
|
};
|
|
|
|
&fec1 {
|
|
phy-mode = "rmii";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_fec1>;
|
|
status = "okay";
|
|
|
|
fixed-link {
|
|
speed = <100>;
|
|
full-duplex;
|
|
};
|
|
|
|
mdio1: mdio {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
status = "okay";
|
|
|
|
switch0: switch0@0 {
|
|
compatible = "marvell,mv88e6085";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_switch>;
|
|
reg = <0>;
|
|
eeprom-length = <512>;
|
|
interrupt-parent = <&gpio3>;
|
|
interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
reset-gpios = <&gpio3 11 GPIO_ACTIVE_LOW>;
|
|
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
port@0 {
|
|
reg = <0>;
|
|
label = "eth_cu_1000_1";
|
|
};
|
|
|
|
port@1 {
|
|
reg = <1>;
|
|
label = "eth_cu_1000_2";
|
|
};
|
|
|
|
port@2 {
|
|
reg = <2>;
|
|
label = "eth_cu_1000_3";
|
|
};
|
|
|
|
port@5 {
|
|
reg = <5>;
|
|
label = "eth_fc_1000_1";
|
|
phy-mode = "1000base-x";
|
|
managed = "in-band-status";
|
|
sfp = <&sff>;
|
|
};
|
|
|
|
port@6 {
|
|
reg = <6>;
|
|
label = "cpu";
|
|
ethernet = <&fec1>;
|
|
|
|
fixed-link {
|
|
speed = <100>;
|
|
full-duplex;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&i2c0 {
|
|
clock-frequency = <400000>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_i2c0>;
|
|
status = "okay";
|
|
|
|
io-expander@22 {
|
|
compatible = "nxp,pca9554";
|
|
reg = <0x22>;
|
|
gpio-controller;
|
|
};
|
|
|
|
lm75@48 {
|
|
compatible = "national,lm75";
|
|
reg = <0x48>;
|
|
};
|
|
|
|
eeprom@52 {
|
|
compatible = "atmel,24c04";
|
|
reg = <0x52>;
|
|
label = "nvm";
|
|
};
|
|
|
|
eeprom@54 {
|
|
compatible = "atmel,24c04";
|
|
reg = <0x54>;
|
|
label = "nameplate";
|
|
};
|
|
};
|
|
|
|
&snvsrtc {
|
|
status = "disabled";
|
|
};
|
|
|
|
&uart0 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_uart0>;
|
|
status = "okay";
|
|
};
|
|
|
|
&iomuxc {
|
|
pinctrl_dspi1: dspi1grp {
|
|
fsl,pins = <
|
|
VF610_PAD_PTD5__DSPI1_CS0 0x1182
|
|
VF610_PAD_PTC6__DSPI1_SIN 0x1181
|
|
VF610_PAD_PTC7__DSPI1_SOUT 0x1182
|
|
VF610_PAD_PTC8__DSPI1_SCK 0x1182
|
|
>;
|
|
};
|
|
|
|
pinctrl_esdhc0: esdhc0grp {
|
|
fsl,pins = <
|
|
VF610_PAD_PTC0__ESDHC0_CLK 0x31ef
|
|
VF610_PAD_PTC1__ESDHC0_CMD 0x31ef
|
|
VF610_PAD_PTC2__ESDHC0_DAT0 0x31ef
|
|
VF610_PAD_PTC3__ESDHC0_DAT1 0x31ef
|
|
VF610_PAD_PTC4__ESDHC0_DAT2 0x31ef
|
|
VF610_PAD_PTC5__ESDHC0_DAT3 0x31ef
|
|
VF610_PAD_PTD23__ESDHC0_DAT4 0x31ef
|
|
VF610_PAD_PTD22__ESDHC0_DAT5 0x31ef
|
|
VF610_PAD_PTD21__ESDHC0_DAT6 0x31ef
|
|
VF610_PAD_PTD20__ESDHC0_DAT7 0x31ef
|
|
>;
|
|
};
|
|
|
|
pinctrl_esdhc1: esdhc1grp {
|
|
fsl,pins = <
|
|
VF610_PAD_PTA24__ESDHC1_CLK 0x31ef
|
|
VF610_PAD_PTA25__ESDHC1_CMD 0x31ef
|
|
VF610_PAD_PTA26__ESDHC1_DAT0 0x31ef
|
|
VF610_PAD_PTA27__ESDHC1_DAT1 0x31ef
|
|
VF610_PAD_PTA28__ESDHC1_DATA2 0x31ef
|
|
VF610_PAD_PTA29__ESDHC1_DAT3 0x31ef
|
|
>;
|
|
};
|
|
|
|
pinctrl_fec1: fec1grp {
|
|
fsl,pins = <
|
|
VF610_PAD_PTA6__RMII_CLKIN 0x30d1
|
|
VF610_PAD_PTC9__ENET_RMII1_MDC 0x30fe
|
|
VF610_PAD_PTC10__ENET_RMII1_MDIO 0x30d3
|
|
VF610_PAD_PTC11__ENET_RMII1_CRS 0x30d1
|
|
VF610_PAD_PTC12__ENET_RMII1_RXD1 0x30d1
|
|
VF610_PAD_PTC13__ENET_RMII1_RXD0 0x30d1
|
|
VF610_PAD_PTC14__ENET_RMII1_RXER 0x30d1
|
|
VF610_PAD_PTC15__ENET_RMII1_TXD1 0x30d2
|
|
VF610_PAD_PTC16__ENET_RMII1_TXD0 0x30d2
|
|
VF610_PAD_PTC17__ENET_RMII1_TXEN 0x30d2
|
|
>;
|
|
};
|
|
|
|
pinctrl_i2c0: i2c0grp {
|
|
fsl,pins = <
|
|
VF610_PAD_PTB14__I2C0_SCL 0x37ff
|
|
VF610_PAD_PTB15__I2C0_SDA 0x37ff
|
|
>;
|
|
};
|
|
|
|
pinctrl_leds_debug: pinctrl-leds-debug {
|
|
fsl,pins = <
|
|
VF610_PAD_PTD3__GPIO_82 0x31c2
|
|
VF610_PAD_PTE3__GPIO_108 0x31c2
|
|
VF610_PAD_PTE4__GPIO_109 0x31c2
|
|
VF610_PAD_PTE5__GPIO_110 0x31c2
|
|
VF610_PAD_PTE6__GPIO_111 0x31c2
|
|
>;
|
|
};
|
|
|
|
pinctrl_optical: optical-grp {
|
|
fsl,pins = <
|
|
/* SFF SD input */
|
|
VF610_PAD_PTE27__GPIO_132 0x3061
|
|
|
|
/* SFF Transmit disable output */
|
|
VF610_PAD_PTE13__GPIO_118 0x3043
|
|
>;
|
|
};
|
|
|
|
pinctrl_switch: switch-grp {
|
|
fsl,pins = <
|
|
VF610_PAD_PTB28__GPIO_98 0x3061
|
|
VF610_PAD_PTE2__GPIO_107 0x1042
|
|
>;
|
|
};
|
|
|
|
pinctrl_uart0: uart0grp {
|
|
fsl,pins = <
|
|
VF610_PAD_PTB10__UART0_TX 0x21a2
|
|
VF610_PAD_PTB11__UART0_RX 0x21a1
|
|
>;
|
|
};
|
|
};
|