mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-19 05:18:41 +07:00
ed616689a3
o min_tx_rate puts lower limit on the VF bandwidth. VF is guaranteed to have a bandwidth of at least this value. max_tx_rate puts cap on the VF bandwidth. VF can have a bandwidth of up to this value. o A new handler set_vf_rate for attr IFLA_VF_RATE has been introduced which takes 4 arguments: netdev, VF number, min_tx_rate, max_tx_rate o ndo_set_vf_rate replaces ndo_set_vf_tx_rate handler. o Drivers that currently implement ndo_set_vf_tx_rate should now call ndo_set_vf_rate instead and reject attempt to set a minimum bandwidth greater than 0 for IFLA_VF_TX_RATE when IFLA_VF_RATE is not yet implemented by driver. o If user enters only one of either min_tx_rate or max_tx_rate, then, userland should read back the other value from driver and set both for IFLA_VF_RATE. Drivers that have not yet implemented IFLA_VF_RATE should always return min_tx_rate as 0 when read from ip tool. o If both IFLA_VF_TX_RATE and IFLA_VF_RATE options are specified, then IFLA_VF_RATE should override. o Idea is to have consistent display of rate values to user. o Usage example: - ./ip link set p4p1 vf 0 rate 900 ./ip link show p4p1 32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT qlen 1000 link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 900 (Mbps), max_tx_rate 900Mbps vf 1 MAC f6:c6:7c:3f:3d:6c vf 2 MAC 56:32:43:98:d7:71 vf 3 MAC d6:be:c3:b5:85:ff vf 4 MAC ee:a9:9a:1e:19:14 vf 5 MAC 4a:d0:4c:07:52:18 vf 6 MAC 3a:76:44:93:62:f9 vf 7 MAC 82:e9:e7:e3:15:1a ./ip link set p4p1 vf 0 max_tx_rate 300 min_tx_rate 200 ./ip link show p4p1 32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT qlen 1000 link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 300 (Mbps), max_tx_rate 300Mbps, min_tx_rate 200Mbps vf 1 MAC f6:c6:7c:3f:3d:6c vf 2 MAC 56:32:43:98:d7:71 vf 3 MAC d6:be:c3:b5:85:ff vf 4 MAC ee:a9:9a:1e:19:14 vf 5 MAC 4a:d0:4c:07:52:18 vf 6 MAC 3a:76:44:93:62:f9 vf 7 MAC 82:e9:e7:e3:15:1a ./ip link set p4p1 vf 0 max_tx_rate 600 rate 300 ./ip link show p4p1 32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT qlen 1000 link/ether 00:0e:1e:08:b0:f brd ff:ff:ff:ff:ff:ff vf 0 MAC 3e:a0:ca:bd:ae:5, tx rate 600 (Mbps), max_tx_rate 600Mbps, min_tx_rate 200Mbps vf 1 MAC f6:c6:7c:3f:3d:6c vf 2 MAC 56:32:43:98:d7:71 vf 3 MAC d6:be:c3:b5:85:ff vf 4 MAC ee:a9:9a:1e:19:14 vf 5 MAC 4a:d0:4c:07:52:18 vf 6 MAC 3a:76:44:93:62:f9 vf 7 MAC 82:e9:e7:e3:15:1a Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
---|---|---|
.. | ||
accessibility | ||
acpi | ||
amba | ||
ata | ||
atm | ||
auxdisplay | ||
base | ||
bcma | ||
block | ||
bluetooth | ||
bus | ||
cdrom | ||
char | ||
clk | ||
clocksource | ||
connector | ||
cpufreq | ||
cpuidle | ||
crypto | ||
dca | ||
devfreq | ||
dio | ||
dma | ||
edac | ||
eisa | ||
extcon | ||
firewire | ||
firmware | ||
fmc | ||
gpio | ||
gpu | ||
hid | ||
hsi | ||
hv | ||
hwmon | ||
hwspinlock | ||
i2c | ||
ide | ||
idle | ||
iio | ||
infiniband | ||
input | ||
iommu | ||
ipack | ||
irqchip | ||
isdn | ||
leds | ||
lguest | ||
macintosh | ||
mailbox | ||
mcb | ||
md | ||
media | ||
memory | ||
memstick | ||
message | ||
mfd | ||
misc | ||
mmc | ||
mtd | ||
net | ||
nfc | ||
ntb | ||
nubus | ||
of | ||
oprofile | ||
parisc | ||
parport | ||
pci | ||
pcmcia | ||
phy | ||
pinctrl | ||
platform | ||
pnp | ||
power | ||
powercap | ||
pps | ||
ps3 | ||
ptp | ||
pwm | ||
rapidio | ||
regulator | ||
remoteproc | ||
reset | ||
rpmsg | ||
rtc | ||
s390 | ||
sbus | ||
scsi | ||
sfi | ||
sh | ||
sn | ||
spi | ||
spmi | ||
ssb | ||
staging | ||
target | ||
tc | ||
thermal | ||
tty | ||
uio | ||
usb | ||
uwb | ||
vfio | ||
vhost | ||
video | ||
virt | ||
virtio | ||
vlynq | ||
vme | ||
w1 | ||
watchdog | ||
xen | ||
zorro | ||
Kconfig | ||
Makefile |