linux_dsm_epyc7002/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi
Neil Armstrong 32122c465c arm64: dts: meson-gxl-s905x-p212: add keep-power-in-suspend property in SDIO node
The WiFi firmware requires that the power is kept enabled while in
suspend mode. Add the keep-power-in-suspend property in the SDIO node
to specify that the power must be kept when entering in a system wide
suspend state.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2019-10-03 08:43:03 -07:00

201 lines
4.0 KiB
Plaintext

// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Copyright (c) 2016 Martin Blumenstingl <martin.blumenstingl@googlemail.com>.
* Based on meson-gx-p23x-q20x.dtsi:
* - Copyright (c) 2016 Endless Computers, Inc.
* Author: Carlo Caione <carlo@endlessm.com>
* - Copyright (c) 2016 BayLibre, SAS.
* Author: Neil Armstrong <narmstrong@baylibre.com>
*/
/* Common DTSI for devices which are based on the P212 reference board. */
#include "meson-gxl-s905x.dtsi"
/ {
aliases {
serial0 = &uart_AO;
serial1 = &uart_A;
ethernet0 = &ethmac;
};
chosen {
stdout-path = "serial0:115200n8";
};
memory@0 {
device_type = "memory";
reg = <0x0 0x0 0x0 0x80000000>;
};
hdmi_5v: regulator-hdmi-5v {
compatible = "regulator-fixed";
regulator-name = "HDMI_5V";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio GPIOH_3 GPIO_ACTIVE_HIGH>;
enable-active-high;
regulator-always-on;
};
vddio_boot: regulator-vddio_boot {
compatible = "regulator-fixed";
regulator-name = "VDDIO_BOOT";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
vddao_3v3: regulator-vddao_3v3 {
compatible = "regulator-fixed";
regulator-name = "VDDAO_3V3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
vddio_ao18: regulator-vddio_ao18 {
compatible = "regulator-fixed";
regulator-name = "VDDIO_AO18";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
vcc_3v3: regulator-vcc_3v3 {
compatible = "regulator-fixed";
regulator-name = "VCC_3V3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
emmc_pwrseq: emmc-pwrseq {
compatible = "mmc-pwrseq-emmc";
reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
};
wifi32k: wifi32k {
compatible = "pwm-clock";
#clock-cells = <0>;
clock-frequency = <32768>;
pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
};
sdio_pwrseq: sdio-pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
clocks = <&wifi32k>;
clock-names = "ext_clock";
};
};
&ethmac {
status = "okay";
};
&ir {
status = "okay";
pinctrl-0 = <&remote_input_ao_pins>;
pinctrl-names = "default";
};
&saradc {
status = "okay";
vref-supply = <&vddio_ao18>;
};
/* Wireless SDIO Module */
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>;
pinctrl-1 = <&sdio_clk_gate_pins>;
pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
bus-width = <4>;
cap-sd-highspeed;
max-frequency = <50000000>;
non-removable;
disable-wp;
/* WiFi firmware requires power to be kept while in suspend */
keep-power-in-suspend;
mmc-pwrseq = <&sdio_pwrseq>;
vmmc-supply = <&vddao_3v3>;
vqmmc-supply = <&vddio_boot>;
};
/* SD card */
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
pinctrl-1 = <&sdcard_clk_gate_pins>;
pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
max-frequency = <50000000>;
disable-wp;
cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
vmmc-supply = <&vddao_3v3>;
vqmmc-supply = <&vddio_boot>;
};
/* eMMC */
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
pinctrl-1 = <&emmc_clk_gate_pins>;
pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
max-frequency = <200000000>;
non-removable;
disable-wp;
mmc-ddr-1_8v;
mmc-hs200-1_8v;
mmc-pwrseq = <&emmc_pwrseq>;
vmmc-supply = <&vcc_3v3>;
vqmmc-supply = <&vddio_boot>;
};
&pwm_ef {
status = "okay";
pinctrl-0 = <&pwm_e_pins>;
pinctrl-names = "default";
clocks = <&clkc CLKID_FCLK_DIV4>;
clock-names = "clkin0";
};
/* This is connected to the Bluetooth module: */
&uart_A {
status = "okay";
pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
pinctrl-names = "default";
uart-has-rtscts;
};
&uart_AO {
status = "okay";
pinctrl-0 = <&uart_ao_a_pins>;
pinctrl-names = "default";
};
&usb0 {
status = "okay";
};
&usb2_phy0 {
/*
* HDMI_5V is also used as supply for the USB VBUS.
*/
phy-supply = <&hdmi_5v>;
};