linux_dsm_epyc7002/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts
Manivannan Sadhasivam 7d578b7d09
arm64: dts: actions: Add uSD and eMMC support for Bubblegum96
Add uSD and eMMC support for Bubblegum96 board based on Actions Semi
S900 SoC. SD0 is connected to uSD slot and SD2 is connected to eMMC.
Since there is no PMIC support added yet, fixed regulator has been
used as a regulator node.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2019-10-22 20:05:42 +05:30

315 lines
8.1 KiB
Plaintext

// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Copyright (c) 2017 Andreas Färber
*/
/dts-v1/;
#include "s900.dtsi"
/ {
compatible = "ucrobotics,bubblegum-96", "actions,s900";
model = "Bubblegum-96";
aliases {
mmc0 = &mmc0;
mmc1 = &mmc1;
mmc2 = &mmc2;
serial5 = &uart5;
};
chosen {
stdout-path = "serial5:115200n8";
};
memory@0 {
device_type = "memory";
reg = <0x0 0x0 0x0 0x80000000>;
};
/* Fixed regulator used in the absence of PMIC */
vcc_3v1: vcc-3v1 {
compatible = "regulator-fixed";
regulator-name = "fixed-3.1V";
regulator-min-microvolt = <3100000>;
regulator-max-microvolt = <3100000>;
regulator-always-on;
};
/* Fixed regulator used in the absence of PMIC */
sd_vcc: sd-vcc {
compatible = "regulator-fixed";
regulator-name = "fixed-3.1V";
regulator-min-microvolt = <3100000>;
regulator-max-microvolt = <3100000>;
regulator-always-on;
};
};
&i2c0 {
status = "disabled";
pinctrl-names = "default";
pinctrl-0 = <&i2c0_default>;
};
&i2c1 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&i2c1_default>;
};
&i2c2 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&i2c2_default>;
};
/*
* GPIO name legend: proper name = the GPIO line is used as GPIO
* NC = not connected (pin out but not routed from the chip to
* anything the board)
* "[PER]" = pin is muxed for [peripheral] (not GPIO)
* LSEC = Low Speed External Connector
* HSEC = High Speed External Connector
*
* Line names are taken from the schematic "Schematics Bubblegum96"
* version v1.0
*
* For the lines routed to the external connectors the
* lines are named after the 96Boards CE Specification 1.0,
* Appendix "Expansion Connector Signal Description".
*
* When the 96Boards naming of a line and the schematic name of
* the same line are in conflict, the 96Boards specification
* takes precedence, which means that the external UART on the
* LSEC is named UART0 while the schematic and SoC names this
* UART2. Only exception is the I2C lines for which the schematic
* naming has been preferred. This is only for the informational
* lines i.e. "[FOO]", the GPIO named lines "GPIO-A" thru "GPIO-L"
* are the only ones actually used for GPIO.
*/
&pinctrl {
gpio-line-names =
"GPIO-A", /* GPIO_0, LSEC pin 23 */
"GPIO-B", /* GPIO_1, LSEC pin 24 */
"GPIO-C", /* GPIO_2, LSEC pin 25 */
"GPIO-D", /* GPIO_3, LSEC pin 26 */
"GPIO-E", /* GPIO_4, LSEC pin 27 */
"GPIO-F", /* GPIO_5, LSEC pin 28 */
"GPIO-G", /* GPIO_6, LSEC pin 29 */
"GPIO-H", /* GPIO_7, LSEC pin 30 */
"GPIO-I", /* GPIO_8, LSEC pin 31 */
"GPIO-J", /* GPIO_9, LSEC pin 32 */
"NC", /* GPIO_10 */
"NC", /* GPIO_11 */
"SIRQ2_1V8", /* GPIO_12 */
"PCM0_OUT", /* GPIO_13 */
"WIFI_LED", /* GPIO_14 */
"PCM0_SYNC", /* GPIO_15 */
"PCM0_CLK", /* GPIO_16 */
"PCM0_IN", /* GPIO_17 */
"BT_LED", /* GPIO_18 */
"LED0", /* GPIO_19 */
"LED1", /* GPIO_20 */
"JTAG_TCK", /* GPIO_21 */
"JTAG_TMS", /* GPIO_22 */
"JTAG_TDI", /* GPIO_23 */
"JTAG_TDO", /* GPIO_24 */
"[UART1_RxD]", /* GPIO_25, LSEC pin 13 */
"NC", /* GPIO_26 */
"[UART1_TxD]", /* GPIO_27, LSEC pin 11 */
"SD0_D0", /* GPIO_28 */
"SD0_D1", /* GPIO_29 */
"SD0_D2", /* GPIO_30 */
"SD0_D3", /* GPIO_31 */
"SD1_D0", /* GPIO_32 */
"SD1_D1", /* GPIO_33 */
"SD1_D2", /* GPIO_34 */
"SD1_D3", /* GPIO_35 */
"SD0_CMD", /* GPIO_36 */
"SD0_CLK", /* GPIO_37 */
"SD1_CMD", /* GPIO_38 */
"SD1_CLK", /* GPIO_39 */
"SPI0_SCLK", /* GPIO_40, LSEC pin 8 */
"SPI0_CS", /* GPIO_41, LSEC pin 12 */
"SPI0_DIN", /* GPIO_42, LSEC pin 10 */
"SPI0_DOUT", /* GPIO_43, LSEC pin 14 */
"I2C5_SDATA", /* GPIO_44, HSEC pin 36 */
"I2C5_SCLK", /* GPIO_45, HSEC pin 38 */
"UART0_RX", /* GPIO_46, LSEC pin 7 */
"UART0_TX", /* GPIO_47, LSEC pin 5 */
"UART0_RTSB", /* GPIO_48, LSEC pin 9 */
"UART0_CTSB", /* GPIO_49, LSEC pin 3 */
"I2C4_SCLK", /* GPIO_50, HSEC pin 32 */
"I2C4_SDATA", /* GPIO_51, HSEC pin 34 */
"I2C0_SCLK", /* GPIO_52 */
"I2C0_SDATA", /* GPIO_53 */
"I2C1_SCLK", /* GPIO_54, LSEC pin 15 */
"I2C1_SDATA", /* GPIO_55, LSEC pin 17 */
"I2C2_SCLK", /* GPIO_56, LSEC pin 19 */
"I2C2_SDATA", /* GPIO_57, LSEC pin 21 */
"CSI0_DN0", /* GPIO_58, HSEC pin 10 */
"CSI0_DP0", /* GPIO_59, HSEC pin 8 */
"CSI0_DN1", /* GPIO_60, HSEC pin 16 */
"CSI0_DP1", /* GPIO_61, HSEC pin 14 */
"CSI0_CN", /* GPIO_62, HSEC pin 4 */
"CSI0_CP", /* GPIO_63, HSEC pin 2 */
"CSI0_DN2", /* GPIO_64, HSEC pin 22 */
"CSI0_DP2", /* GPIO_65, HSEC pin 20 */
"CSI0_DN3", /* GPIO_66, HSEC pin 28 */
"CSI0_DP3", /* GPIO_67, HSEC pin 26 */
"[CLK0]", /* GPIO_68, HSEC pin 15 */
"CSI1_DN0", /* GPIO_69, HSEC pin 44 */
"CSI1_DP0", /* GPIO_70, HSEC pin 42 */
"CSI1_DN1", /* GPIO_71, HSEC pin 50 */
"CSI1_DP1", /* GPIO_72, HSEC pin 48 */
"CSI1_CN", /* GPIO_73, HSEC pin 56 */
"CSI1_CP", /* GPIO_74, HSEC pin 54 */
"[CLK1]", /* GPIO_75, HSEC pin 17 */
"[GPIOD0]", /* GPIO_76 */
"[GPIOD1]", /* GPIO_77 */
"BT_RST_N", /* GPIO_78 */
"EXT_DC_EN", /* GPIO_79 */
"[PCM_DI]", /* GPIO_80, LSEC pin 22 */
"[PCM_DO]", /* GPIO_81, LSEC pin 20 */
"[PCM_CLK]", /* GPIO_82, LSEC pin 18 */
"[PCM_FS]", /* GPIO_83, LSEC pin 16 */
"WAKE_BT", /* GPIO_84 */
"WL_REG_ON", /* GPIO_85 */
"NC", /* GPIO_86 */
"NC", /* GPIO_87 */
"NC", /* GPIO_88 */
"NC", /* GPIO_89 */
"NC", /* GPIO_90 */
"WIFI_WAKE", /* GPIO_91 */
"BT_WAKE", /* GPIO_92 */
"NC", /* GPIO_93 */
"OTG_EN2", /* GPIO_94 */
"OTG_EN", /* GPIO_95 */
"DSI_DP3", /* GPIO_96, HSEC pin 45 */
"DSI_DN3", /* GPIO_97, HSEC pin 47 */
"DSI_DP1", /* GPIO_98, HSEC pin 33 */
"DSI_DN1", /* GPIO_99, HSEC pin 35 */
"DSI_CP", /* GPIO_100, HSEC pin 21 */
"DSI_CN", /* GPIO_101, HSEC pin 23 */
"DSI_DP0", /* GPIO_102, HSEC pin 27 */
"DSI_DN0", /* GPIO_103, HSEC pin 29 */
"DSI_DP2", /* GPIO_104, HSEC pin 39 */
"DSI_DN2", /* GPIO_105, HSEC pin 41 */
"N0_D0", /* GPIO_106 */
"N0_D1", /* GPIO_107 */
"N0_D2", /* GPIO_108 */
"N0_D3", /* GPIO_109 */
"N0_D4", /* GPIO_110 */
"N0_D5", /* GPIO_111 */
"N0_D6", /* GPIO_112 */
"N0_D7", /* GPIO_113 */
"N0_DQS", /* GPIO_114 */
"N0_DQSN", /* GPIO_115 */
"NC", /* GPIO_116 */
"NC", /* GPIO_117 */
"NC", /* GPIO_118 */
"N0_CEB1", /* GPIO_119 */
"CARD_DT", /* GPIO_120 */
"N0_CEB3", /* GPIO_121 */
"SD_DAT0", /* GPIO_122, HSEC pin 1 */
"SD_DAT1", /* GPIO_123, HSEC pin 3 */
"SD_DAT2", /* GPIO_124, HSEC pin 5 */
"SD_DAT3", /* GPIO_125, HSEC pin 7 */
"NC", /* GPIO_126 */
"NC", /* GPIO_127 */
"[PWR_BTN_N]", /* GPIO_128, LSEC pin 4 */
"[RST_BTN_N]", /* GPIO_129, LSEC pin 6 */
"NC", /* GPIO_130 */
"SD_CMD", /* GPIO_131 */
"GPIO-L", /* GPIO_132, LSEC pin 34 */
"GPIO-K", /* GPIO_133, LSEC pin 33 */
"NC", /* GPIO_134 */
"SD_SCLK", /* GPIO_135 */
"NC", /* GPIO_136 */
"JTAG_TRST", /* GPIO_137 */
"I2C3_SCLK", /* GPIO_138 */
"LED2", /* GPIO_139 */
"LED3", /* GPIO_140 */
"I2C3_SDATA", /* GPIO_141 */
"UART3_RX", /* GPIO_142 */
"UART3_TX", /* GPIO_143 */
"UART3_RTSB", /* GPIO_144 */
"UART3_CTSB"; /* GPIO_145 */
i2c0_default: i2c0-default {
pinmux {
groups = "i2c0_mfp";
function = "i2c0";
};
pinconf {
pins = "i2c0_sclk", "i2c0_sdata";
bias-pull-up;
};
};
i2c1_default: i2c1-default {
pinconf {
pins = "i2c1_sclk", "i2c1_sdata";
bias-pull-up;
};
};
i2c2_default: i2c2-default {
pinconf {
pins = "i2c2_sclk", "i2c2_sdata";
bias-pull-up;
};
};
mmc0_default: mmc0_default {
pinmux {
groups = "sd0_d0_mfp", "sd0_d1_mfp", "sd0_d2_d3_mfp",
"sd0_cmd_mfp", "sd0_clk_mfp";
function = "sd0";
};
};
mmc2_default: mmc2_default {
pinmux {
groups = "nand0_d0_ceb3_mfp";
function = "sd2";
};
};
};
/* uSD */
&mmc0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mmc0_default>;
no-sdio;
no-mmc;
no-1-8-v;
cd-gpios = <&pinctrl 120 GPIO_ACTIVE_LOW>;
bus-width = <4>;
vmmc-supply = <&sd_vcc>;
vqmmc-supply = <&sd_vcc>;
};
/* eMMC */
&mmc2 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mmc2_default>;
no-sdio;
no-sd;
non-removable;
bus-width = <8>;
vmmc-supply = <&vcc_3v1>;
};
&timer {
clocks = <&hosc>;
};
&uart5 {
status = "okay";
};