linux_dsm_epyc7002/drivers/mmc/host/sdhci.h
Éric Piel 35ff8554d1 sdhci: activate led support also when module
CONFIG_LEDS_CLASS is defined only if led-class is built-in, otherwise
when it is a module the option is called CONFIG_LEDS_CLASS_MODULE. Led
support should also be activated in this case.

Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-12-31 18:18:11 +01:00

289 lines
8.9 KiB
C

/*
* linux/drivers/mmc/host/sdhci.h - Secure Digital Host Controller Interface driver
*
* Copyright (C) 2005-2008 Pierre Ossman, All Rights Reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or (at
* your option) any later version.
*/
#include <linux/scatterlist.h>
/*
* Controller registers
*/
#define SDHCI_DMA_ADDRESS 0x00
#define SDHCI_BLOCK_SIZE 0x04
#define SDHCI_MAKE_BLKSZ(dma, blksz) (((dma & 0x7) << 12) | (blksz & 0xFFF))
#define SDHCI_BLOCK_COUNT 0x06
#define SDHCI_ARGUMENT 0x08
#define SDHCI_TRANSFER_MODE 0x0C
#define SDHCI_TRNS_DMA 0x01
#define SDHCI_TRNS_BLK_CNT_EN 0x02
#define SDHCI_TRNS_ACMD12 0x04
#define SDHCI_TRNS_READ 0x10
#define SDHCI_TRNS_MULTI 0x20
#define SDHCI_COMMAND 0x0E
#define SDHCI_CMD_RESP_MASK 0x03
#define SDHCI_CMD_CRC 0x08
#define SDHCI_CMD_INDEX 0x10
#define SDHCI_CMD_DATA 0x20
#define SDHCI_CMD_RESP_NONE 0x00
#define SDHCI_CMD_RESP_LONG 0x01
#define SDHCI_CMD_RESP_SHORT 0x02
#define SDHCI_CMD_RESP_SHORT_BUSY 0x03
#define SDHCI_MAKE_CMD(c, f) (((c & 0xff) << 8) | (f & 0xff))
#define SDHCI_RESPONSE 0x10
#define SDHCI_BUFFER 0x20
#define SDHCI_PRESENT_STATE 0x24
#define SDHCI_CMD_INHIBIT 0x00000001
#define SDHCI_DATA_INHIBIT 0x00000002
#define SDHCI_DOING_WRITE 0x00000100
#define SDHCI_DOING_READ 0x00000200
#define SDHCI_SPACE_AVAILABLE 0x00000400
#define SDHCI_DATA_AVAILABLE 0x00000800
#define SDHCI_CARD_PRESENT 0x00010000
#define SDHCI_WRITE_PROTECT 0x00080000
#define SDHCI_HOST_CONTROL 0x28
#define SDHCI_CTRL_LED 0x01
#define SDHCI_CTRL_4BITBUS 0x02
#define SDHCI_CTRL_HISPD 0x04
#define SDHCI_CTRL_DMA_MASK 0x18
#define SDHCI_CTRL_SDMA 0x00
#define SDHCI_CTRL_ADMA1 0x08
#define SDHCI_CTRL_ADMA32 0x10
#define SDHCI_CTRL_ADMA64 0x18
#define SDHCI_POWER_CONTROL 0x29
#define SDHCI_POWER_ON 0x01
#define SDHCI_POWER_180 0x0A
#define SDHCI_POWER_300 0x0C
#define SDHCI_POWER_330 0x0E
#define SDHCI_BLOCK_GAP_CONTROL 0x2A
#define SDHCI_WAKE_UP_CONTROL 0x2B
#define SDHCI_CLOCK_CONTROL 0x2C
#define SDHCI_DIVIDER_SHIFT 8
#define SDHCI_CLOCK_CARD_EN 0x0004
#define SDHCI_CLOCK_INT_STABLE 0x0002
#define SDHCI_CLOCK_INT_EN 0x0001
#define SDHCI_TIMEOUT_CONTROL 0x2E
#define SDHCI_SOFTWARE_RESET 0x2F
#define SDHCI_RESET_ALL 0x01
#define SDHCI_RESET_CMD 0x02
#define SDHCI_RESET_DATA 0x04
#define SDHCI_INT_STATUS 0x30
#define SDHCI_INT_ENABLE 0x34
#define SDHCI_SIGNAL_ENABLE 0x38
#define SDHCI_INT_RESPONSE 0x00000001
#define SDHCI_INT_DATA_END 0x00000002
#define SDHCI_INT_DMA_END 0x00000008
#define SDHCI_INT_SPACE_AVAIL 0x00000010
#define SDHCI_INT_DATA_AVAIL 0x00000020
#define SDHCI_INT_CARD_INSERT 0x00000040
#define SDHCI_INT_CARD_REMOVE 0x00000080
#define SDHCI_INT_CARD_INT 0x00000100
#define SDHCI_INT_ERROR 0x00008000
#define SDHCI_INT_TIMEOUT 0x00010000
#define SDHCI_INT_CRC 0x00020000
#define SDHCI_INT_END_BIT 0x00040000
#define SDHCI_INT_INDEX 0x00080000
#define SDHCI_INT_DATA_TIMEOUT 0x00100000
#define SDHCI_INT_DATA_CRC 0x00200000
#define SDHCI_INT_DATA_END_BIT 0x00400000
#define SDHCI_INT_BUS_POWER 0x00800000
#define SDHCI_INT_ACMD12ERR 0x01000000
#define SDHCI_INT_ADMA_ERROR 0x02000000
#define SDHCI_INT_NORMAL_MASK 0x00007FFF
#define SDHCI_INT_ERROR_MASK 0xFFFF8000
#define SDHCI_INT_CMD_MASK (SDHCI_INT_RESPONSE | SDHCI_INT_TIMEOUT | \
SDHCI_INT_CRC | SDHCI_INT_END_BIT | SDHCI_INT_INDEX)
#define SDHCI_INT_DATA_MASK (SDHCI_INT_DATA_END | SDHCI_INT_DMA_END | \
SDHCI_INT_DATA_AVAIL | SDHCI_INT_SPACE_AVAIL | \
SDHCI_INT_DATA_TIMEOUT | SDHCI_INT_DATA_CRC | \
SDHCI_INT_DATA_END_BIT)
#define SDHCI_ACMD12_ERR 0x3C
/* 3E-3F reserved */
#define SDHCI_CAPABILITIES 0x40
#define SDHCI_TIMEOUT_CLK_MASK 0x0000003F
#define SDHCI_TIMEOUT_CLK_SHIFT 0
#define SDHCI_TIMEOUT_CLK_UNIT 0x00000080
#define SDHCI_CLOCK_BASE_MASK 0x00003F00
#define SDHCI_CLOCK_BASE_SHIFT 8
#define SDHCI_MAX_BLOCK_MASK 0x00030000
#define SDHCI_MAX_BLOCK_SHIFT 16
#define SDHCI_CAN_DO_ADMA2 0x00080000
#define SDHCI_CAN_DO_ADMA1 0x00100000
#define SDHCI_CAN_DO_HISPD 0x00200000
#define SDHCI_CAN_DO_DMA 0x00400000
#define SDHCI_CAN_VDD_330 0x01000000
#define SDHCI_CAN_VDD_300 0x02000000
#define SDHCI_CAN_VDD_180 0x04000000
#define SDHCI_CAN_64BIT 0x10000000
/* 44-47 reserved for more caps */
#define SDHCI_MAX_CURRENT 0x48
/* 4C-4F reserved for more max current */
#define SDHCI_SET_ACMD12_ERROR 0x50
#define SDHCI_SET_INT_ERROR 0x52
#define SDHCI_ADMA_ERROR 0x54
/* 55-57 reserved */
#define SDHCI_ADMA_ADDRESS 0x58
/* 60-FB reserved */
#define SDHCI_SLOT_INT_STATUS 0xFC
#define SDHCI_HOST_VERSION 0xFE
#define SDHCI_VENDOR_VER_MASK 0xFF00
#define SDHCI_VENDOR_VER_SHIFT 8
#define SDHCI_SPEC_VER_MASK 0x00FF
#define SDHCI_SPEC_VER_SHIFT 0
#define SDHCI_SPEC_100 0
#define SDHCI_SPEC_200 1
struct sdhci_ops;
struct sdhci_host {
/* Data set by hardware interface driver */
const char *hw_name; /* Hardware bus name */
unsigned int quirks; /* Deviations from spec. */
/* Controller doesn't honor resets unless we touch the clock register */
#define SDHCI_QUIRK_CLOCK_BEFORE_RESET (1<<0)
/* Controller has bad caps bits, but really supports DMA */
#define SDHCI_QUIRK_FORCE_DMA (1<<1)
/* Controller doesn't like to be reset when there is no card inserted. */
#define SDHCI_QUIRK_NO_CARD_NO_RESET (1<<2)
/* Controller doesn't like clearing the power reg before a change */
#define SDHCI_QUIRK_SINGLE_POWER_WRITE (1<<3)
/* Controller has flaky internal state so reset it on each ios change */
#define SDHCI_QUIRK_RESET_CMD_DATA_ON_IOS (1<<4)
/* Controller has an unusable DMA engine */
#define SDHCI_QUIRK_BROKEN_DMA (1<<5)
/* Controller has an unusable ADMA engine */
#define SDHCI_QUIRK_BROKEN_ADMA (1<<6)
/* Controller can only DMA from 32-bit aligned addresses */
#define SDHCI_QUIRK_32BIT_DMA_ADDR (1<<7)
/* Controller can only DMA chunk sizes that are a multiple of 32 bits */
#define SDHCI_QUIRK_32BIT_DMA_SIZE (1<<8)
/* Controller can only ADMA chunks that are a multiple of 32 bits */
#define SDHCI_QUIRK_32BIT_ADMA_SIZE (1<<9)
/* Controller needs to be reset after each request to stay stable */
#define SDHCI_QUIRK_RESET_AFTER_REQUEST (1<<10)
/* Controller needs voltage and power writes to happen separately */
#define SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER (1<<11)
/* Controller provides an incorrect timeout value for transfers */
#define SDHCI_QUIRK_BROKEN_TIMEOUT_VAL (1<<12)
/* Controller has an issue with buffer bits for small transfers */
#define SDHCI_QUIRK_BROKEN_SMALL_PIO (1<<13)
/* Controller supports high speed but doesn't have the caps bit set */
#define SDHCI_QUIRK_FORCE_HIGHSPEED (1<<14)
int irq; /* Device IRQ */
void __iomem * ioaddr; /* Mapped address */
const struct sdhci_ops *ops; /* Low level hw interface */
/* Internal data */
struct mmc_host *mmc; /* MMC structure */
u64 dma_mask; /* custom DMA mask */
#if defined(CONFIG_LEDS_CLASS) || defined(CONFIG_LEDS_CLASS_MODULE)
struct led_classdev led; /* LED control */
#endif
spinlock_t lock; /* Mutex */
int flags; /* Host attributes */
#define SDHCI_USE_DMA (1<<0) /* Host is DMA capable */
#define SDHCI_USE_ADMA (1<<1) /* Host is ADMA capable */
#define SDHCI_REQ_USE_DMA (1<<2) /* Use DMA for this req. */
#define SDHCI_DEVICE_DEAD (1<<3) /* Device unresponsive */
unsigned int version; /* SDHCI spec. version */
unsigned int max_clk; /* Max possible freq (MHz) */
unsigned int timeout_clk; /* Timeout freq (KHz) */
unsigned int clock; /* Current clock (MHz) */
unsigned short power; /* Current voltage */
struct mmc_request *mrq; /* Current request */
struct mmc_command *cmd; /* Current command */
struct mmc_data *data; /* Current data request */
unsigned int data_early:1; /* Data finished before cmd */
struct sg_mapping_iter sg_miter; /* SG state for PIO */
unsigned int blocks; /* remaining PIO blocks */
int sg_count; /* Mapped sg entries */
u8 *adma_desc; /* ADMA descriptor table */
u8 *align_buffer; /* Bounce buffer */
dma_addr_t adma_addr; /* Mapped ADMA descr. table */
dma_addr_t align_addr; /* Mapped bounce buffer */
struct tasklet_struct card_tasklet; /* Tasklet structures */
struct tasklet_struct finish_tasklet;
struct timer_list timer; /* Timer for timeouts */
unsigned long private[0] ____cacheline_aligned;
};
struct sdhci_ops {
int (*enable_dma)(struct sdhci_host *host);
};
extern struct sdhci_host *sdhci_alloc_host(struct device *dev,
size_t priv_size);
extern void sdhci_free_host(struct sdhci_host *host);
static inline void *sdhci_priv(struct sdhci_host *host)
{
return (void *)host->private;
}
extern int sdhci_add_host(struct sdhci_host *host);
extern void sdhci_remove_host(struct sdhci_host *host, int dead);
#ifdef CONFIG_PM
extern int sdhci_suspend_host(struct sdhci_host *host, pm_message_t state);
extern int sdhci_resume_host(struct sdhci_host *host);
#endif