mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-22 19:03:28 +07:00
3ae4f3aac0
R-Car GPIO controller provides two interfaces to set GPIO line output signal state, and for a particular GPIO line the selected interface is determined by OUTDTSEL bit value. At the moment the driver supports only one of two interfaces, namely OUTDT General Output Register is used to control the output signal. While this selection is the default one on reset, it is not explicitly configured on probe, thus it might be possible that kernel and userspace consumers of a GPIO won't be able to set the wanted GPIO output signal. Below is a simple test case to reproduce the described problem and verify this fix in the kernel on H3 ULCB by setting non-default OUTDTSEL configuration from a bootloader: u-boot > mw.l 0xe6055440 0x3000 1 ... userspace > echo default-on > /sys/devices/platform/leds/leds/led5/trigger userspace > echo default-on > /sys/devices/platform/leds/leds/led6/trigger Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
612 lines
16 KiB
C
612 lines
16 KiB
C
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* Renesas R-Car GPIO Support
|
|
*
|
|
* Copyright (C) 2014 Renesas Electronics Corporation
|
|
* Copyright (C) 2013 Magnus Damm
|
|
*/
|
|
|
|
#include <linux/err.h>
|
|
#include <linux/gpio/driver.h>
|
|
#include <linux/init.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/io.h>
|
|
#include <linux/ioport.h>
|
|
#include <linux/irq.h>
|
|
#include <linux/module.h>
|
|
#include <linux/of.h>
|
|
#include <linux/of_device.h>
|
|
#include <linux/pinctrl/consumer.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/pm_runtime.h>
|
|
#include <linux/spinlock.h>
|
|
#include <linux/slab.h>
|
|
|
|
struct gpio_rcar_bank_info {
|
|
u32 iointsel;
|
|
u32 inoutsel;
|
|
u32 outdt;
|
|
u32 posneg;
|
|
u32 edglevel;
|
|
u32 bothedge;
|
|
u32 intmsk;
|
|
};
|
|
|
|
struct gpio_rcar_priv {
|
|
void __iomem *base;
|
|
spinlock_t lock;
|
|
struct device *dev;
|
|
struct gpio_chip gpio_chip;
|
|
struct irq_chip irq_chip;
|
|
unsigned int irq_parent;
|
|
atomic_t wakeup_path;
|
|
bool has_outdtsel;
|
|
bool has_both_edge_trigger;
|
|
struct gpio_rcar_bank_info bank_info;
|
|
};
|
|
|
|
#define IOINTSEL 0x00 /* General IO/Interrupt Switching Register */
|
|
#define INOUTSEL 0x04 /* General Input/Output Switching Register */
|
|
#define OUTDT 0x08 /* General Output Register */
|
|
#define INDT 0x0c /* General Input Register */
|
|
#define INTDT 0x10 /* Interrupt Display Register */
|
|
#define INTCLR 0x14 /* Interrupt Clear Register */
|
|
#define INTMSK 0x18 /* Interrupt Mask Register */
|
|
#define MSKCLR 0x1c /* Interrupt Mask Clear Register */
|
|
#define POSNEG 0x20 /* Positive/Negative Logic Select Register */
|
|
#define EDGLEVEL 0x24 /* Edge/level Select Register */
|
|
#define FILONOFF 0x28 /* Chattering Prevention On/Off Register */
|
|
#define OUTDTSEL 0x40 /* Output Data Select Register */
|
|
#define BOTHEDGE 0x4c /* One Edge/Both Edge Select Register */
|
|
|
|
#define RCAR_MAX_GPIO_PER_BANK 32
|
|
|
|
static inline u32 gpio_rcar_read(struct gpio_rcar_priv *p, int offs)
|
|
{
|
|
return ioread32(p->base + offs);
|
|
}
|
|
|
|
static inline void gpio_rcar_write(struct gpio_rcar_priv *p, int offs,
|
|
u32 value)
|
|
{
|
|
iowrite32(value, p->base + offs);
|
|
}
|
|
|
|
static void gpio_rcar_modify_bit(struct gpio_rcar_priv *p, int offs,
|
|
int bit, bool value)
|
|
{
|
|
u32 tmp = gpio_rcar_read(p, offs);
|
|
|
|
if (value)
|
|
tmp |= BIT(bit);
|
|
else
|
|
tmp &= ~BIT(bit);
|
|
|
|
gpio_rcar_write(p, offs, tmp);
|
|
}
|
|
|
|
static void gpio_rcar_irq_disable(struct irq_data *d)
|
|
{
|
|
struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
|
|
struct gpio_rcar_priv *p = gpiochip_get_data(gc);
|
|
|
|
gpio_rcar_write(p, INTMSK, ~BIT(irqd_to_hwirq(d)));
|
|
}
|
|
|
|
static void gpio_rcar_irq_enable(struct irq_data *d)
|
|
{
|
|
struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
|
|
struct gpio_rcar_priv *p = gpiochip_get_data(gc);
|
|
|
|
gpio_rcar_write(p, MSKCLR, BIT(irqd_to_hwirq(d)));
|
|
}
|
|
|
|
static void gpio_rcar_config_interrupt_input_mode(struct gpio_rcar_priv *p,
|
|
unsigned int hwirq,
|
|
bool active_high_rising_edge,
|
|
bool level_trigger,
|
|
bool both)
|
|
{
|
|
unsigned long flags;
|
|
|
|
/* follow steps in the GPIO documentation for
|
|
* "Setting Edge-Sensitive Interrupt Input Mode" and
|
|
* "Setting Level-Sensitive Interrupt Input Mode"
|
|
*/
|
|
|
|
spin_lock_irqsave(&p->lock, flags);
|
|
|
|
/* Configure postive or negative logic in POSNEG */
|
|
gpio_rcar_modify_bit(p, POSNEG, hwirq, !active_high_rising_edge);
|
|
|
|
/* Configure edge or level trigger in EDGLEVEL */
|
|
gpio_rcar_modify_bit(p, EDGLEVEL, hwirq, !level_trigger);
|
|
|
|
/* Select one edge or both edges in BOTHEDGE */
|
|
if (p->has_both_edge_trigger)
|
|
gpio_rcar_modify_bit(p, BOTHEDGE, hwirq, both);
|
|
|
|
/* Select "Interrupt Input Mode" in IOINTSEL */
|
|
gpio_rcar_modify_bit(p, IOINTSEL, hwirq, true);
|
|
|
|
/* Write INTCLR in case of edge trigger */
|
|
if (!level_trigger)
|
|
gpio_rcar_write(p, INTCLR, BIT(hwirq));
|
|
|
|
spin_unlock_irqrestore(&p->lock, flags);
|
|
}
|
|
|
|
static int gpio_rcar_irq_set_type(struct irq_data *d, unsigned int type)
|
|
{
|
|
struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
|
|
struct gpio_rcar_priv *p = gpiochip_get_data(gc);
|
|
unsigned int hwirq = irqd_to_hwirq(d);
|
|
|
|
dev_dbg(p->dev, "sense irq = %d, type = %d\n", hwirq, type);
|
|
|
|
switch (type & IRQ_TYPE_SENSE_MASK) {
|
|
case IRQ_TYPE_LEVEL_HIGH:
|
|
gpio_rcar_config_interrupt_input_mode(p, hwirq, true, true,
|
|
false);
|
|
break;
|
|
case IRQ_TYPE_LEVEL_LOW:
|
|
gpio_rcar_config_interrupt_input_mode(p, hwirq, false, true,
|
|
false);
|
|
break;
|
|
case IRQ_TYPE_EDGE_RISING:
|
|
gpio_rcar_config_interrupt_input_mode(p, hwirq, true, false,
|
|
false);
|
|
break;
|
|
case IRQ_TYPE_EDGE_FALLING:
|
|
gpio_rcar_config_interrupt_input_mode(p, hwirq, false, false,
|
|
false);
|
|
break;
|
|
case IRQ_TYPE_EDGE_BOTH:
|
|
if (!p->has_both_edge_trigger)
|
|
return -EINVAL;
|
|
gpio_rcar_config_interrupt_input_mode(p, hwirq, true, false,
|
|
true);
|
|
break;
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
static int gpio_rcar_irq_set_wake(struct irq_data *d, unsigned int on)
|
|
{
|
|
struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
|
|
struct gpio_rcar_priv *p = gpiochip_get_data(gc);
|
|
int error;
|
|
|
|
if (p->irq_parent) {
|
|
error = irq_set_irq_wake(p->irq_parent, on);
|
|
if (error) {
|
|
dev_dbg(p->dev, "irq %u doesn't support irq_set_wake\n",
|
|
p->irq_parent);
|
|
p->irq_parent = 0;
|
|
}
|
|
}
|
|
|
|
if (on)
|
|
atomic_inc(&p->wakeup_path);
|
|
else
|
|
atomic_dec(&p->wakeup_path);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static irqreturn_t gpio_rcar_irq_handler(int irq, void *dev_id)
|
|
{
|
|
struct gpio_rcar_priv *p = dev_id;
|
|
u32 pending;
|
|
unsigned int offset, irqs_handled = 0;
|
|
|
|
while ((pending = gpio_rcar_read(p, INTDT) &
|
|
gpio_rcar_read(p, INTMSK))) {
|
|
offset = __ffs(pending);
|
|
gpio_rcar_write(p, INTCLR, BIT(offset));
|
|
generic_handle_irq(irq_find_mapping(p->gpio_chip.irq.domain,
|
|
offset));
|
|
irqs_handled++;
|
|
}
|
|
|
|
return irqs_handled ? IRQ_HANDLED : IRQ_NONE;
|
|
}
|
|
|
|
static void gpio_rcar_config_general_input_output_mode(struct gpio_chip *chip,
|
|
unsigned int gpio,
|
|
bool output)
|
|
{
|
|
struct gpio_rcar_priv *p = gpiochip_get_data(chip);
|
|
unsigned long flags;
|
|
|
|
/* follow steps in the GPIO documentation for
|
|
* "Setting General Output Mode" and
|
|
* "Setting General Input Mode"
|
|
*/
|
|
|
|
spin_lock_irqsave(&p->lock, flags);
|
|
|
|
/* Configure postive logic in POSNEG */
|
|
gpio_rcar_modify_bit(p, POSNEG, gpio, false);
|
|
|
|
/* Select "General Input/Output Mode" in IOINTSEL */
|
|
gpio_rcar_modify_bit(p, IOINTSEL, gpio, false);
|
|
|
|
/* Select Input Mode or Output Mode in INOUTSEL */
|
|
gpio_rcar_modify_bit(p, INOUTSEL, gpio, output);
|
|
|
|
/* Select General Output Register to output data in OUTDTSEL */
|
|
if (p->has_outdtsel && output)
|
|
gpio_rcar_modify_bit(p, OUTDTSEL, gpio, false);
|
|
|
|
spin_unlock_irqrestore(&p->lock, flags);
|
|
}
|
|
|
|
static int gpio_rcar_request(struct gpio_chip *chip, unsigned offset)
|
|
{
|
|
struct gpio_rcar_priv *p = gpiochip_get_data(chip);
|
|
int error;
|
|
|
|
error = pm_runtime_get_sync(p->dev);
|
|
if (error < 0)
|
|
return error;
|
|
|
|
error = pinctrl_gpio_request(chip->base + offset);
|
|
if (error)
|
|
pm_runtime_put(p->dev);
|
|
|
|
return error;
|
|
}
|
|
|
|
static void gpio_rcar_free(struct gpio_chip *chip, unsigned offset)
|
|
{
|
|
struct gpio_rcar_priv *p = gpiochip_get_data(chip);
|
|
|
|
pinctrl_gpio_free(chip->base + offset);
|
|
|
|
/*
|
|
* Set the GPIO as an input to ensure that the next GPIO request won't
|
|
* drive the GPIO pin as an output.
|
|
*/
|
|
gpio_rcar_config_general_input_output_mode(chip, offset, false);
|
|
|
|
pm_runtime_put(p->dev);
|
|
}
|
|
|
|
static int gpio_rcar_get_direction(struct gpio_chip *chip, unsigned int offset)
|
|
{
|
|
struct gpio_rcar_priv *p = gpiochip_get_data(chip);
|
|
|
|
return !(gpio_rcar_read(p, INOUTSEL) & BIT(offset));
|
|
}
|
|
|
|
static int gpio_rcar_direction_input(struct gpio_chip *chip, unsigned offset)
|
|
{
|
|
gpio_rcar_config_general_input_output_mode(chip, offset, false);
|
|
return 0;
|
|
}
|
|
|
|
static int gpio_rcar_get(struct gpio_chip *chip, unsigned offset)
|
|
{
|
|
u32 bit = BIT(offset);
|
|
|
|
/* testing on r8a7790 shows that INDT does not show correct pin state
|
|
* when configured as output, so use OUTDT in case of output pins */
|
|
if (gpio_rcar_read(gpiochip_get_data(chip), INOUTSEL) & bit)
|
|
return !!(gpio_rcar_read(gpiochip_get_data(chip), OUTDT) & bit);
|
|
else
|
|
return !!(gpio_rcar_read(gpiochip_get_data(chip), INDT) & bit);
|
|
}
|
|
|
|
static void gpio_rcar_set(struct gpio_chip *chip, unsigned offset, int value)
|
|
{
|
|
struct gpio_rcar_priv *p = gpiochip_get_data(chip);
|
|
unsigned long flags;
|
|
|
|
spin_lock_irqsave(&p->lock, flags);
|
|
gpio_rcar_modify_bit(p, OUTDT, offset, value);
|
|
spin_unlock_irqrestore(&p->lock, flags);
|
|
}
|
|
|
|
static void gpio_rcar_set_multiple(struct gpio_chip *chip, unsigned long *mask,
|
|
unsigned long *bits)
|
|
{
|
|
struct gpio_rcar_priv *p = gpiochip_get_data(chip);
|
|
unsigned long flags;
|
|
u32 val, bankmask;
|
|
|
|
bankmask = mask[0] & GENMASK(chip->ngpio - 1, 0);
|
|
if (chip->valid_mask)
|
|
bankmask &= chip->valid_mask[0];
|
|
|
|
if (!bankmask)
|
|
return;
|
|
|
|
spin_lock_irqsave(&p->lock, flags);
|
|
val = gpio_rcar_read(p, OUTDT);
|
|
val &= ~bankmask;
|
|
val |= (bankmask & bits[0]);
|
|
gpio_rcar_write(p, OUTDT, val);
|
|
spin_unlock_irqrestore(&p->lock, flags);
|
|
}
|
|
|
|
static int gpio_rcar_direction_output(struct gpio_chip *chip, unsigned offset,
|
|
int value)
|
|
{
|
|
/* write GPIO value to output before selecting output mode of pin */
|
|
gpio_rcar_set(chip, offset, value);
|
|
gpio_rcar_config_general_input_output_mode(chip, offset, true);
|
|
return 0;
|
|
}
|
|
|
|
struct gpio_rcar_info {
|
|
bool has_outdtsel;
|
|
bool has_both_edge_trigger;
|
|
};
|
|
|
|
static const struct gpio_rcar_info gpio_rcar_info_gen1 = {
|
|
.has_outdtsel = false,
|
|
.has_both_edge_trigger = false,
|
|
};
|
|
|
|
static const struct gpio_rcar_info gpio_rcar_info_gen2 = {
|
|
.has_outdtsel = true,
|
|
.has_both_edge_trigger = true,
|
|
};
|
|
|
|
static const struct of_device_id gpio_rcar_of_table[] = {
|
|
{
|
|
.compatible = "renesas,gpio-r8a7743",
|
|
/* RZ/G1 GPIO is identical to R-Car Gen2. */
|
|
.data = &gpio_rcar_info_gen2,
|
|
}, {
|
|
.compatible = "renesas,gpio-r8a7790",
|
|
.data = &gpio_rcar_info_gen2,
|
|
}, {
|
|
.compatible = "renesas,gpio-r8a7791",
|
|
.data = &gpio_rcar_info_gen2,
|
|
}, {
|
|
.compatible = "renesas,gpio-r8a7792",
|
|
.data = &gpio_rcar_info_gen2,
|
|
}, {
|
|
.compatible = "renesas,gpio-r8a7793",
|
|
.data = &gpio_rcar_info_gen2,
|
|
}, {
|
|
.compatible = "renesas,gpio-r8a7794",
|
|
.data = &gpio_rcar_info_gen2,
|
|
}, {
|
|
.compatible = "renesas,gpio-r8a7795",
|
|
/* Gen3 GPIO is identical to Gen2. */
|
|
.data = &gpio_rcar_info_gen2,
|
|
}, {
|
|
.compatible = "renesas,gpio-r8a7796",
|
|
/* Gen3 GPIO is identical to Gen2. */
|
|
.data = &gpio_rcar_info_gen2,
|
|
}, {
|
|
.compatible = "renesas,rcar-gen1-gpio",
|
|
.data = &gpio_rcar_info_gen1,
|
|
}, {
|
|
.compatible = "renesas,rcar-gen2-gpio",
|
|
.data = &gpio_rcar_info_gen2,
|
|
}, {
|
|
.compatible = "renesas,rcar-gen3-gpio",
|
|
/* Gen3 GPIO is identical to Gen2. */
|
|
.data = &gpio_rcar_info_gen2,
|
|
}, {
|
|
.compatible = "renesas,gpio-rcar",
|
|
.data = &gpio_rcar_info_gen1,
|
|
}, {
|
|
/* Terminator */
|
|
},
|
|
};
|
|
|
|
MODULE_DEVICE_TABLE(of, gpio_rcar_of_table);
|
|
|
|
static int gpio_rcar_parse_dt(struct gpio_rcar_priv *p, unsigned int *npins)
|
|
{
|
|
struct device_node *np = p->dev->of_node;
|
|
const struct gpio_rcar_info *info;
|
|
struct of_phandle_args args;
|
|
int ret;
|
|
|
|
info = of_device_get_match_data(p->dev);
|
|
p->has_outdtsel = info->has_outdtsel;
|
|
p->has_both_edge_trigger = info->has_both_edge_trigger;
|
|
|
|
ret = of_parse_phandle_with_fixed_args(np, "gpio-ranges", 3, 0, &args);
|
|
*npins = ret == 0 ? args.args[2] : RCAR_MAX_GPIO_PER_BANK;
|
|
|
|
if (*npins == 0 || *npins > RCAR_MAX_GPIO_PER_BANK) {
|
|
dev_warn(p->dev, "Invalid number of gpio lines %u, using %u\n",
|
|
*npins, RCAR_MAX_GPIO_PER_BANK);
|
|
*npins = RCAR_MAX_GPIO_PER_BANK;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int gpio_rcar_probe(struct platform_device *pdev)
|
|
{
|
|
struct gpio_rcar_priv *p;
|
|
struct resource *io, *irq;
|
|
struct gpio_chip *gpio_chip;
|
|
struct irq_chip *irq_chip;
|
|
struct device *dev = &pdev->dev;
|
|
const char *name = dev_name(dev);
|
|
unsigned int npins;
|
|
int ret;
|
|
|
|
p = devm_kzalloc(dev, sizeof(*p), GFP_KERNEL);
|
|
if (!p)
|
|
return -ENOMEM;
|
|
|
|
p->dev = dev;
|
|
spin_lock_init(&p->lock);
|
|
|
|
/* Get device configuration from DT node */
|
|
ret = gpio_rcar_parse_dt(p, &npins);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
platform_set_drvdata(pdev, p);
|
|
|
|
pm_runtime_enable(dev);
|
|
|
|
irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
|
|
if (!irq) {
|
|
dev_err(dev, "missing IRQ\n");
|
|
ret = -EINVAL;
|
|
goto err0;
|
|
}
|
|
|
|
io = platform_get_resource(pdev, IORESOURCE_MEM, 0);
|
|
p->base = devm_ioremap_resource(dev, io);
|
|
if (IS_ERR(p->base)) {
|
|
ret = PTR_ERR(p->base);
|
|
goto err0;
|
|
}
|
|
|
|
gpio_chip = &p->gpio_chip;
|
|
gpio_chip->request = gpio_rcar_request;
|
|
gpio_chip->free = gpio_rcar_free;
|
|
gpio_chip->get_direction = gpio_rcar_get_direction;
|
|
gpio_chip->direction_input = gpio_rcar_direction_input;
|
|
gpio_chip->get = gpio_rcar_get;
|
|
gpio_chip->direction_output = gpio_rcar_direction_output;
|
|
gpio_chip->set = gpio_rcar_set;
|
|
gpio_chip->set_multiple = gpio_rcar_set_multiple;
|
|
gpio_chip->label = name;
|
|
gpio_chip->parent = dev;
|
|
gpio_chip->owner = THIS_MODULE;
|
|
gpio_chip->base = -1;
|
|
gpio_chip->ngpio = npins;
|
|
|
|
irq_chip = &p->irq_chip;
|
|
irq_chip->name = name;
|
|
irq_chip->parent_device = dev;
|
|
irq_chip->irq_mask = gpio_rcar_irq_disable;
|
|
irq_chip->irq_unmask = gpio_rcar_irq_enable;
|
|
irq_chip->irq_set_type = gpio_rcar_irq_set_type;
|
|
irq_chip->irq_set_wake = gpio_rcar_irq_set_wake;
|
|
irq_chip->flags = IRQCHIP_SET_TYPE_MASKED | IRQCHIP_MASK_ON_SUSPEND;
|
|
|
|
ret = gpiochip_add_data(gpio_chip, p);
|
|
if (ret) {
|
|
dev_err(dev, "failed to add GPIO controller\n");
|
|
goto err0;
|
|
}
|
|
|
|
ret = gpiochip_irqchip_add(gpio_chip, irq_chip, 0, handle_level_irq,
|
|
IRQ_TYPE_NONE);
|
|
if (ret) {
|
|
dev_err(dev, "cannot add irqchip\n");
|
|
goto err1;
|
|
}
|
|
|
|
p->irq_parent = irq->start;
|
|
if (devm_request_irq(dev, irq->start, gpio_rcar_irq_handler,
|
|
IRQF_SHARED, name, p)) {
|
|
dev_err(dev, "failed to request IRQ\n");
|
|
ret = -ENOENT;
|
|
goto err1;
|
|
}
|
|
|
|
dev_info(dev, "driving %d GPIOs\n", npins);
|
|
|
|
return 0;
|
|
|
|
err1:
|
|
gpiochip_remove(gpio_chip);
|
|
err0:
|
|
pm_runtime_disable(dev);
|
|
return ret;
|
|
}
|
|
|
|
static int gpio_rcar_remove(struct platform_device *pdev)
|
|
{
|
|
struct gpio_rcar_priv *p = platform_get_drvdata(pdev);
|
|
|
|
gpiochip_remove(&p->gpio_chip);
|
|
|
|
pm_runtime_disable(&pdev->dev);
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_PM_SLEEP
|
|
static int gpio_rcar_suspend(struct device *dev)
|
|
{
|
|
struct gpio_rcar_priv *p = dev_get_drvdata(dev);
|
|
|
|
p->bank_info.iointsel = gpio_rcar_read(p, IOINTSEL);
|
|
p->bank_info.inoutsel = gpio_rcar_read(p, INOUTSEL);
|
|
p->bank_info.outdt = gpio_rcar_read(p, OUTDT);
|
|
p->bank_info.intmsk = gpio_rcar_read(p, INTMSK);
|
|
p->bank_info.posneg = gpio_rcar_read(p, POSNEG);
|
|
p->bank_info.edglevel = gpio_rcar_read(p, EDGLEVEL);
|
|
if (p->has_both_edge_trigger)
|
|
p->bank_info.bothedge = gpio_rcar_read(p, BOTHEDGE);
|
|
|
|
if (atomic_read(&p->wakeup_path))
|
|
device_set_wakeup_path(dev);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int gpio_rcar_resume(struct device *dev)
|
|
{
|
|
struct gpio_rcar_priv *p = dev_get_drvdata(dev);
|
|
unsigned int offset;
|
|
u32 mask;
|
|
|
|
for (offset = 0; offset < p->gpio_chip.ngpio; offset++) {
|
|
if (!gpiochip_line_is_valid(&p->gpio_chip, offset))
|
|
continue;
|
|
|
|
mask = BIT(offset);
|
|
/* I/O pin */
|
|
if (!(p->bank_info.iointsel & mask)) {
|
|
if (p->bank_info.inoutsel & mask)
|
|
gpio_rcar_direction_output(
|
|
&p->gpio_chip, offset,
|
|
!!(p->bank_info.outdt & mask));
|
|
else
|
|
gpio_rcar_direction_input(&p->gpio_chip,
|
|
offset);
|
|
} else {
|
|
/* Interrupt pin */
|
|
gpio_rcar_config_interrupt_input_mode(
|
|
p,
|
|
offset,
|
|
!(p->bank_info.posneg & mask),
|
|
!(p->bank_info.edglevel & mask),
|
|
!!(p->bank_info.bothedge & mask));
|
|
|
|
if (p->bank_info.intmsk & mask)
|
|
gpio_rcar_write(p, MSKCLR, mask);
|
|
}
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
#endif /* CONFIG_PM_SLEEP*/
|
|
|
|
static SIMPLE_DEV_PM_OPS(gpio_rcar_pm_ops, gpio_rcar_suspend, gpio_rcar_resume);
|
|
|
|
static struct platform_driver gpio_rcar_device_driver = {
|
|
.probe = gpio_rcar_probe,
|
|
.remove = gpio_rcar_remove,
|
|
.driver = {
|
|
.name = "gpio_rcar",
|
|
.pm = &gpio_rcar_pm_ops,
|
|
.of_match_table = of_match_ptr(gpio_rcar_of_table),
|
|
}
|
|
};
|
|
|
|
module_platform_driver(gpio_rcar_device_driver);
|
|
|
|
MODULE_AUTHOR("Magnus Damm");
|
|
MODULE_DESCRIPTION("Renesas R-Car GPIO Driver");
|
|
MODULE_LICENSE("GPL v2");
|