mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-06 02:46:42 +07:00
b918f6e62c
Add a swsusp debugging mode. This does everything that's needed for a suspend except for actually suspending. So we can look in the log messages and work out a) what code is being slow and b) which drivers are misbehaving. (1) # echo testproc > /sys/power/disk # echo disk > /sys/power/state This should turn off the non-boot CPU, freeze all processes, wait for 5 seconds and then thaw the processes and the CPU. (2) # echo test > /sys/power/disk # echo disk > /sys/power/state This should turn off the non-boot CPU, freeze all processes, shrink memory, suspend all devices, wait for 5 seconds, resume the devices etc. Cc: Pavel Machek <pavel@ucw.cz> Cc: Stefan Seyfried <seife@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
83 lines
3.5 KiB
Plaintext
83 lines
3.5 KiB
Plaintext
Power Management Interface
|
|
|
|
|
|
The power management subsystem provides a unified sysfs interface to
|
|
userspace, regardless of what architecture or platform one is
|
|
running. The interface exists in /sys/power/ directory (assuming sysfs
|
|
is mounted at /sys).
|
|
|
|
/sys/power/state controls system power state. Reading from this file
|
|
returns what states are supported, which is hard-coded to 'standby'
|
|
(Power-On Suspend), 'mem' (Suspend-to-RAM), and 'disk'
|
|
(Suspend-to-Disk).
|
|
|
|
Writing to this file one of those strings causes the system to
|
|
transition into that state. Please see the file
|
|
Documentation/power/states.txt for a description of each of those
|
|
states.
|
|
|
|
|
|
/sys/power/disk controls the operating mode of the suspend-to-disk
|
|
mechanism. Suspend-to-disk can be handled in several ways. The
|
|
greatest distinction is who writes memory to disk - the firmware or
|
|
the kernel. If the firmware does it, we assume that it also handles
|
|
suspending the system.
|
|
|
|
If the kernel does it, then we have three options for putting the system
|
|
to sleep - using the platform driver (e.g. ACPI or other PM
|
|
registers), powering off the system or rebooting the system (for
|
|
testing). The system will support either 'firmware' or 'platform', and
|
|
that is known a priori. But, the user may choose 'shutdown' or
|
|
'reboot' as alternatives.
|
|
|
|
Additionally, /sys/power/disk can be used to turn on one of the two testing
|
|
modes of the suspend-to-disk mechanism: 'testproc' or 'test'. If the
|
|
suspend-to-disk mechanism is in the 'testproc' mode, writing 'disk' to
|
|
/sys/power/state will cause the kernel to disable nonboot CPUs and freeze
|
|
tasks, wait for 5 seconds, unfreeze tasks and enable nonboot CPUs. If it is
|
|
in the 'test' mode, writing 'disk' to /sys/power/state will cause the kernel
|
|
to disable nonboot CPUs and freeze tasks, shrink memory, suspend devices, wait
|
|
for 5 seconds, resume devices, unfreeze tasks and enable nonboot CPUs. Then,
|
|
we are able to look in the log messages and work out, for example, which code
|
|
is being slow and which device drivers are misbehaving.
|
|
|
|
Reading from this file will display what the mode is currently set
|
|
to. Writing to this file will accept one of
|
|
|
|
'firmware'
|
|
'platform'
|
|
'shutdown'
|
|
'reboot'
|
|
'testproc'
|
|
'test'
|
|
|
|
It will only change to 'firmware' or 'platform' if the system supports
|
|
it.
|
|
|
|
/sys/power/image_size controls the size of the image created by
|
|
the suspend-to-disk mechanism. It can be written a string
|
|
representing a non-negative integer that will be used as an upper
|
|
limit of the image size, in bytes. The suspend-to-disk mechanism will
|
|
do its best to ensure the image size will not exceed that number. However,
|
|
if this turns out to be impossible, it will try to suspend anyway using the
|
|
smallest image possible. In particular, if "0" is written to this file, the
|
|
suspend image will be as small as possible.
|
|
|
|
Reading from this file will display the current image size limit, which
|
|
is set to 500 MB by default.
|
|
|
|
/sys/power/pm_trace controls the code which saves the last PM event point in
|
|
the RTC across reboots, so that you can debug a machine that just hangs
|
|
during suspend (or more commonly, during resume). Namely, the RTC is only
|
|
used to save the last PM event point if this file contains '1'. Initially it
|
|
contains '0' which may be changed to '1' by writing a string representing a
|
|
nonzero integer into it.
|
|
|
|
To use this debugging feature you should attempt to suspend the machine, then
|
|
reboot it and run
|
|
|
|
dmesg -s 1000000 | grep 'hash matches'
|
|
|
|
CAUTION: Using it will cause your machine's real-time (CMOS) clock to be
|
|
set to a random invalid time after a resume.
|