mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-28 11:18:45 +07:00
e1b2dc70cd
The BCM2835 GPIO module is a combined GPIO controller, (GPIO) interrupt controller, and pinmux/control device. Original driver by Simon Arlott. Rewrite including GPIO chip device by Chris Boot. Upstreaming changes by Stephen Warren: * Wrote DT binding documentation. * Changed brcm,function to an integer to more directly match the datasheet, and to match brcm,pins being an integer. * Implemented pull-up/down pin config. * Removed read-only DT property and related code. The restriction this implemented are driven by the board, not the GPIO HW block, so don't really make sense of a HW block binding, were in general incomplete (since they could only know about the few pins hard-coded into the Raspberry Pi B board design and not the uncommitted GPIOS), and are better represented simply by not writing incorrect data into pin configuration nodes. * Don't set GPIO_IN function select in gpio_request_enable() to avoid glitches; defer this to gpio_set_direction(). Consequently, removed empty bcm2835_pmx_gpio_request_enable(). * Simplified enabled_irq_map[]; make it explicitly 1 entry per bank. * Lifted use of enabled_irq_map[] outside the per-interrupt loop in IRQ handler, thus fixing an issue where the code was indexing into enabled_irq_map[] by intra-bank GPIO ID, not global GPIO ID. * Removed locking in IRQ handler, since all other code uses spin_lock_irqsave() and so guarantees it doesn't run concurrently with the handler. * Moved duplicated BUILD_BUG_ON()s into probe(). Also check size of bcm2835_gpio_pins[]. * Remove range-checking from bcm2835_pctl_get_groups_count() since we've decided to trust the pinctrl core. * Made bcm2835_pmx_gpio_disable_free() call bcm2835_pinctrl_fsel_set() directly for simplicity. * Fixed body of dt_free_map() to match latest dt_node_to_map(). * Removed GPIO ownership check from bcm2835_pmx_enable() since the pinctrl core owns doing this. * Made irq_chip and pinctrl_gpio_range .name == MODULE_NAME so it's more descriptive. * Simplified remove(); removed call to non-existent pinctrl_remove_gpio_range(), remove early return on error. * Don't force gpiochip's base to 0. Set gpio_range.base to gpiochip's base GPIO number. * Error-handling cleanups in probe(). * Switched to module_platform_driver() rather than open-coding. * Made pin, group, and function names lower-case. * s/broadcom/brcm/ in DT property names. * s/2708/2835/. * Fixed a couple minor checkpatch warnings, and other minor cleanup. Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Signed-off-by: Chris Boot <bootc@bootc.net> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> |
||
|---|---|---|
| .. | ||
| brcm,bcm2835-gpio.txt | ||
| fsl,imx6q-pinctrl.txt | ||
| fsl,imx35-pinctrl.txt | ||
| fsl,imx51-pinctrl.txt | ||
| fsl,imx53-pinctrl.txt | ||
| fsl,imx-pinctrl.txt | ||
| fsl,mxs-pinctrl.txt | ||
| nvidia,tegra20-pinmux.txt | ||
| nvidia,tegra30-pinmux.txt | ||
| pinctrl_spear.txt | ||
| pinctrl-bindings.txt | ||
| pinctrl-single.txt | ||