mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-28 11:18:45 +07:00
de623ece5b
Add support for non-dma pcm for imx platforms with imx-pcm-fiq support. Instead of imx-pcm-audio, in this case imx-pcm-fiq-audio device is added and the SIER flags are set differently. We need imx-pcm-fiq for some boards that use an incompatible codec. imx-pcm-fiq handles those codecs differently and allows to operate with them. DMA is not possible because some data sent by the codecs, e.g. wm9712, is not in the datastream. Also some data is mixed up in the fifos, so that we need to sort them out manually. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Tested-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Mark Brown <broonie@linaro.org>
78 lines
4.3 KiB
Plaintext
78 lines
4.3 KiB
Plaintext
Freescale Synchronous Serial Interface
|
|
|
|
The SSI is a serial device that communicates with audio codecs. It can
|
|
be programmed in AC97, I2S, left-justified, or right-justified modes.
|
|
|
|
Required properties:
|
|
- compatible: Compatible list, contains "fsl,ssi".
|
|
- cell-index: The SSI, <0> = SSI1, <1> = SSI2, and so on.
|
|
- reg: Offset and length of the register set for the device.
|
|
- interrupts: <a b> where a is the interrupt number and b is a
|
|
field that represents an encoding of the sense and
|
|
level information for the interrupt. This should be
|
|
encoded based on the information in section 2)
|
|
depending on the type of interrupt controller you
|
|
have.
|
|
- interrupt-parent: The phandle for the interrupt controller that
|
|
services interrupts for this device.
|
|
- fsl,mode: The operating mode for the SSI interface.
|
|
"i2s-slave" - I2S mode, SSI is clock slave
|
|
"i2s-master" - I2S mode, SSI is clock master
|
|
"lj-slave" - left-justified mode, SSI is clock slave
|
|
"lj-master" - l.j. mode, SSI is clock master
|
|
"rj-slave" - right-justified mode, SSI is clock slave
|
|
"rj-master" - r.j., SSI is clock master
|
|
"ac97-slave" - AC97 mode, SSI is clock slave
|
|
"ac97-master" - AC97 mode, SSI is clock master
|
|
- fsl,playback-dma: Phandle to a node for the DMA channel to use for
|
|
playback of audio. This is typically dictated by SOC
|
|
design. See the notes below.
|
|
- fsl,capture-dma: Phandle to a node for the DMA channel to use for
|
|
capture (recording) of audio. This is typically dictated
|
|
by SOC design. See the notes below.
|
|
- fsl,fifo-depth: The number of elements in the transmit and receive FIFOs.
|
|
This number is the maximum allowed value for SFCSR[TFWM0].
|
|
- fsl,ssi-asynchronous:
|
|
If specified, the SSI is to be programmed in asynchronous
|
|
mode. In this mode, pins SRCK, STCK, SRFS, and STFS must
|
|
all be connected to valid signals. In synchronous mode,
|
|
SRCK and SRFS are ignored. Asynchronous mode allows
|
|
playback and capture to use different sample sizes and
|
|
sample rates. Some drivers may require that SRCK and STCK
|
|
be connected together, and SRFS and STFS be connected
|
|
together. This would still allow different sample sizes,
|
|
but not different sample rates.
|
|
|
|
Optional properties:
|
|
- codec-handle: Phandle to a 'codec' node that defines an audio
|
|
codec connected to this SSI. This node is typically
|
|
a child of an I2C or other control node.
|
|
- fsl,fiq-stream-filter: Bool property. Disabled DMA and use FIQ instead to
|
|
filter the codec stream. This is necessary for some boards
|
|
where an incompatible codec is connected to this SSI, e.g.
|
|
on pca100 and pcm043.
|
|
|
|
Child 'codec' node required properties:
|
|
- compatible: Compatible list, contains the name of the codec
|
|
|
|
Child 'codec' node optional properties:
|
|
- clock-frequency: The frequency of the input clock, which typically comes
|
|
from an on-board dedicated oscillator.
|
|
|
|
Notes on fsl,playback-dma and fsl,capture-dma:
|
|
|
|
On SOCs that have an SSI, specific DMA channels are hard-wired for playback
|
|
and capture. On the MPC8610, for example, SSI1 must use DMA channel 0 for
|
|
playback and DMA channel 1 for capture. SSI2 must use DMA channel 2 for
|
|
playback and DMA channel 3 for capture. The developer can choose which
|
|
DMA controller to use, but the channels themselves are hard-wired. The
|
|
purpose of these two properties is to represent this hardware design.
|
|
|
|
The device tree nodes for the DMA channels that are referenced by
|
|
"fsl,playback-dma" and "fsl,capture-dma" must be marked as compatible with
|
|
"fsl,ssi-dma-channel". The SOC-specific compatible string (e.g.
|
|
"fsl,mpc8610-dma-channel") can remain. If these nodes are left as
|
|
"fsl,elo-dma-channel" or "fsl,eloplus-dma-channel", then the generic Elo DMA
|
|
drivers (fsldma) will attempt to use them, and it will conflict with the
|
|
sound drivers.
|