linux_dsm_epyc7002/drivers/net/atl1/atl1_hw.c

/*
 * Copyright(c) 2005 - 2006 Attansic Corporation. All rights reserved.
 * Copyright(c) 2006 Chris Snook <csnook@redhat.com>
 * Copyright(c) 2006 Jay Cliburn <jcliburn@gmail.com>
 *
 * Derived from Intel e1000 driver
 * Copyright(c) 1999 - 2005 Intel Corporation. All rights reserved.
 *
 * This program is free software; you can redistribute it and/or modify it
 * under the terms of the GNU General Public License as published by the Free
 * Software Foundation; either version 2 of the License, or (at your option)
 * any later version.
 *
 * This program is distributed in the hope that it will be useful, but WITHOUT
 * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
 * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
 * more details.
 *
 * You should have received a copy of the GNU General Public License along with
 * this program; if not, write to the Free Software Foundation, Inc., 59
 * Temple Place - Suite 330, Boston, MA  02111-1307, USA.
 */

#include <linux/types.h>
#include <linux/pci.h>
#include <linux/delay.h>
#include <linux/if_vlan.h>
#include <linux/etherdevice.h>
#include <linux/crc32.h>
#include <asm/byteorder.h>

#include "atl1.h"

/*
 * Reset the transmit and receive units; mask and clear all interrupts.
 * hw - Struct containing variables accessed by shared code
 * return : ATL1_SUCCESS  or  idle status (if error)
 */
s32 atl1_reset_hw(struct atl1_hw *hw)
{
	struct pci_dev *pdev = hw->back->pdev;
	u32 icr;
	int i;

	/*
	 * Clear Interrupt mask to stop board from generating
	 * interrupts & Clear any pending interrupt events
	 */
	/*
	 * iowrite32(0, hw->hw_addr + REG_IMR);
	 * iowrite32(0xffffffff, hw->hw_addr + REG_ISR);
	 */

	/*
	 * Issue Soft Reset to the MAC.  This will reset the chip's
	 * transmit, receive, DMA.  It will not effect
	 * the current PCI configuration.  The global reset bit is self-
	 * clearing, and should clear within a microsecond.
	 */
	iowrite32(MASTER_CTRL_SOFT_RST, hw->hw_addr + REG_MASTER_CTRL);
	ioread32(hw->hw_addr + REG_MASTER_CTRL);

	iowrite16(1, hw->hw_addr + REG_GPHY_ENABLE);
	ioread16(hw->hw_addr + REG_GPHY_ENABLE);

	msleep(1);		/* delay about 1ms */

	/* Wait at least 10ms for All module to be Idle */
	for (i = 0; i < 10; i++) {
		icr = ioread32(hw->hw_addr + REG_IDLE_STATUS);
		if (!icr)
			break;
		msleep(1);	/* delay 1 ms */
		cpu_relax();	/* FIXME: is this still the right way to do this? */
	}

	if (icr) {
		dev_dbg(&pdev->dev, "ICR = 0x%x\n", icr);
		return icr;
	}

	return ATL1_SUCCESS;
}

/* function about EEPROM
 *
 * check_eeprom_exist
 * return 0 if eeprom exist
 */
static int atl1_check_eeprom_exist(struct atl1_hw *hw)
{
	u32 value;
	value = ioread32(hw->hw_addr + REG_SPI_FLASH_CTRL);
	if (value & SPI_FLASH_CTRL_EN_VPD) {
		value &= ~SPI_FLASH_CTRL_EN_VPD;
		iowrite32(value, hw->hw_addr + REG_SPI_FLASH_CTRL);
	}

	value = ioread16(hw->hw_addr + REG_PCIE_CAP_LIST);
	return ((value & 0xFF00) == 0x6C00) ? 0 : 1;
}

static bool atl1_read_eeprom(struct atl1_hw *hw, u32 offset, u32 *p_value)
{
	int i;
	u32 control;

	if (offset & 3)
		return false;	/* address do not align */

	iowrite32(0, hw->hw_addr + REG_VPD_DATA);
	control = (offset & VPD_CAP_VPD_ADDR_MASK) << VPD_CAP_VPD_ADDR_SHIFT;
	iowrite32(control, hw->hw_addr + REG_VPD_CAP);
	ioread32(hw->hw_addr + REG_VPD_CAP);

	for (i = 0; i < 10; i++) {
		msleep(2);
		control = ioread32(hw->hw_addr + REG_VPD_CAP);
		if (control & VPD_CAP_VPD_FLAG)
			break;
	}
	if (control & VPD_CAP_VPD_FLAG) {
		*p_value = ioread32(hw->hw_addr + REG_VPD_DATA);
		return true;
	}
	return false;		/* timeout */
}

/*
 * Reads the value from a PHY register
 * hw - Struct containing variables accessed by shared code
 * reg_addr - address of the PHY register to read
 */
s32 atl1_read_phy_reg(struct atl1_hw *hw, u16 reg_addr, u16 *phy_data)
{
	u32 val;
	int i;

	val = ((u32) (reg_addr & MDIO_REG_ADDR_MASK)) << MDIO_REG_ADDR_SHIFT |
		MDIO_START | MDIO_SUP_PREAMBLE | MDIO_RW | MDIO_CLK_25_4 <<
		MDIO_CLK_SEL_SHIFT;
	iowrite32(val, hw->hw_addr + REG_MDIO_CTRL);
	ioread32(hw->hw_addr + REG_MDIO_CTRL);

	for (i = 0; i < MDIO_WAIT_TIMES; i++) {
		udelay(2);
		val = ioread32(hw->hw_addr + REG_MDIO_CTRL);
		if (!(val & (MDIO_START | MDIO_BUSY)))
			break;
	}
	if (!(val & (MDIO_START | MDIO_BUSY))) {
		*phy_data = (u16) val;
		return ATL1_SUCCESS;
	}
	return ATL1_ERR_PHY;
}

#define CUSTOM_SPI_CS_SETUP	2
#define CUSTOM_SPI_CLK_HI	2
#define CUSTOM_SPI_CLK_LO	2
#define CUSTOM_SPI_CS_HOLD	2
#define CUSTOM_SPI_CS_HI	3

static bool atl1_spi_read(struct atl1_hw *hw, u32 addr, u32 *buf)
{
	int i;
	u32 value;

	iowrite32(0, hw->hw_addr + REG_SPI_DATA);
	iowrite32(addr, hw->hw_addr + REG_SPI_ADDR);

	value = SPI_FLASH_CTRL_WAIT_READY |
	    (CUSTOM_SPI_CS_SETUP & SPI_FLASH_CTRL_CS_SETUP_MASK) <<
	    SPI_FLASH_CTRL_CS_SETUP_SHIFT | (CUSTOM_SPI_CLK_HI &
					     SPI_FLASH_CTRL_CLK_HI_MASK) <<
	    SPI_FLASH_CTRL_CLK_HI_SHIFT | (CUSTOM_SPI_CLK_LO &
					   SPI_FLASH_CTRL_CLK_LO_MASK) <<
	    SPI_FLASH_CTRL_CLK_LO_SHIFT | (CUSTOM_SPI_CS_HOLD &
					   SPI_FLASH_CTRL_CS_HOLD_MASK) <<
	    SPI_FLASH_CTRL_CS_HOLD_SHIFT | (CUSTOM_SPI_CS_HI &
					    SPI_FLASH_CTRL_CS_HI_MASK) <<
	    SPI_FLASH_CTRL_CS_HI_SHIFT | (1 & SPI_FLASH_CTRL_INS_MASK) <<
	    SPI_FLASH_CTRL_INS_SHIFT;

	iowrite32(value, hw->hw_addr + REG_SPI_FLASH_CTRL);

	value |= SPI_FLASH_CTRL_START;
	iowrite32(value, hw->hw_addr + REG_SPI_FLASH_CTRL);
	ioread32(hw->hw_addr + REG_SPI_FLASH_CTRL);

	for (i = 0; i < 10; i++) {
		msleep(1);	/* 1ms */
		value = ioread32(hw->hw_addr + REG_SPI_FLASH_CTRL);
		if (!(value & SPI_FLASH_CTRL_START))
			break;
	}

	if (value & SPI_FLASH_CTRL_START)
		return false;

	*buf = ioread32(hw->hw_addr + REG_SPI_DATA);

	return true;
}

/*
 * get_permanent_address
 * return 0 if get valid mac address,
 */
static int atl1_get_permanent_address(struct atl1_hw *hw)
{
	u32 addr[2];
	u32 i, control;
	u16 reg;
	u8 eth_addr[ETH_ALEN];
	bool key_valid;

	if (is_valid_ether_addr(hw->perm_mac_addr))
		return 0;

	/* init */
	addr[0] = addr[1] = 0;

	if (!atl1_check_eeprom_exist(hw)) {	/* eeprom exist */
		reg = 0;
		key_valid = false;
		/* Read out all EEPROM content */
		i = 0;
		while (1) {
			if (atl1_read_eeprom(hw, i + 0x100, &control)) {
				if (key_valid) {
					if (reg == REG_MAC_STA_ADDR)
						addr[0] = control;
					else if (reg == (REG_MAC_STA_ADDR + 4))
						addr[1] = control;
					key_valid = false;
				} else if ((control & 0xff) == 0x5A) {
					key_valid = true;
					reg = (u16) (control >> 16);
				} else
					break;	/* assume data end while encount an invalid KEYWORD */
			} else
				break;	/* read error */
			i += 4;
		}

		*(u32 *) &eth_addr[2] = swab32(addr[0]);
		*(u16 *) &eth_addr[0] = swab16(*(u16 *) &addr[1]);
		if (is_valid_ether_addr(eth_addr)) {
			memcpy(hw->perm_mac_addr, eth_addr, ETH_ALEN);
			return 0;
		}
		return 1;
	}

	/* see if SPI FLAGS exist ? */
	addr[0] = addr[1] = 0;
	reg = 0;
	key_valid = false;
	i = 0;
	while (1) {
		if (atl1_spi_read(hw, i + 0x1f000, &control)) {
			if (key_valid) {
				if (reg == REG_MAC_STA_ADDR)
					addr[0] = control;
				else if (reg == (REG_MAC_STA_ADDR + 4))
					addr[1] = control;
				key_valid = false;
			} else if ((control & 0xff) == 0x5A) {
				key_valid = true;
				reg = (u16) (control >> 16);
			} else
				break;	/* data end */
		} else
			break;	/* read error */
		i += 4;
	}

	*(u32 *) &eth_addr[2] = swab32(addr[0]);
	*(u16 *) &eth_addr[0] = swab16(*(u16 *) &addr[1]);
	if (is_valid_ether_addr(eth_addr)) {
		memcpy(hw->perm_mac_addr, eth_addr, ETH_ALEN);
		return 0;
	}

	/*
	 * On some motherboards, the MAC address is written by the
	 * BIOS directly to the MAC register during POST, and is
	 * not stored in eeprom.  If all else thus far has failed
	 * to fetch the permanent MAC address, try reading it directly.
	 */
	addr[0] = ioread32(hw->hw_addr + REG_MAC_STA_ADDR);
	addr[1] = ioread16(hw->hw_addr + (REG_MAC_STA_ADDR + 4));
	*(u32 *) &eth_addr[2] = swab32(addr[0]);
	*(u16 *) &eth_addr[0] = swab16(*(u16 *) &addr[1]);
	if (is_valid_ether_addr(eth_addr)) {
		memcpy(hw->perm_mac_addr, eth_addr, ETH_ALEN);
		return 0;
	}

	return 1;
}

/*
 * Reads the adapter's MAC address from the EEPROM
 * hw - Struct containing variables accessed by shared code
 */
s32 atl1_read_mac_addr(struct atl1_hw *hw)
{
	u16 i;

	if (atl1_get_permanent_address(hw))
		random_ether_addr(hw->perm_mac_addr);

	for (i = 0; i < ETH_ALEN; i++)
		hw->mac_addr[i] = hw->perm_mac_addr[i];
	return ATL1_SUCCESS;
}

/*
 * Hashes an address to determine its location in the multicast table
 * hw - Struct containing variables accessed by shared code
 * mc_addr - the multicast address to hash
 *
 * atl1_hash_mc_addr
 *  purpose
 *      set hash value for a multicast address
 *      hash calcu processing :
 *          1. calcu 32bit CRC for multicast address
 *          2. reverse crc with MSB to LSB
 */
u32 atl1_hash_mc_addr(struct atl1_hw *hw, u8 *mc_addr)
{
	u32 crc32, value = 0;
	int i;

	crc32 = ether_crc_le(6, mc_addr);
	for (i = 0; i < 32; i++)
		value |= (((crc32 >> i) & 1) << (31 - i));

	return value;
}

/*
 * Sets the bit in the multicast table corresponding to the hash value.
 * hw - Struct containing variables accessed by shared code
 * hash_value - Multicast address hash value
 */
void atl1_hash_set(struct atl1_hw *hw, u32 hash_value)
{
	u32 hash_bit, hash_reg;
	u32 mta;

	/*
	 * The HASH Table  is a register array of 2 32-bit registers.
	 * It is treated like an array of 64 bits.  We want to set
	 * bit BitArray[hash_value]. So we figure out what register
	 * the bit is in, read it, OR in the new bit, then write
	 * back the new value.  The register is determined by the
	 * upper 7 bits of the hash value and the bit within that
	 * register are determined by the lower 5 bits of the value.
	 */
	hash_reg = (hash_value >> 31) & 0x1;
	hash_bit = (hash_value >> 26) & 0x1F;
	mta = ioread32((hw->hw_addr + REG_RX_HASH_TABLE) + (hash_reg << 2));
	mta |= (1 << hash_bit);
	iowrite32(mta, (hw->hw_addr + REG_RX_HASH_TABLE) + (hash_reg << 2));
}

/*
 * Writes a value to a PHY register
 * hw - Struct containing variables accessed by shared code
 * reg_addr - address of the PHY register to write
 * data - data to write to the PHY
 */
s32 atl1_write_phy_reg(struct atl1_hw *hw, u32 reg_addr, u16 phy_data)
{
	int i;
	u32 val;

	val = ((u32) (phy_data & MDIO_DATA_MASK)) << MDIO_DATA_SHIFT |
	    (reg_addr & MDIO_REG_ADDR_MASK) << MDIO_REG_ADDR_SHIFT |
	    MDIO_SUP_PREAMBLE |
	    MDIO_START | MDIO_CLK_25_4 << MDIO_CLK_SEL_SHIFT;
	iowrite32(val, hw->hw_addr + REG_MDIO_CTRL);
	ioread32(hw->hw_addr + REG_MDIO_CTRL);

	for (i = 0; i < MDIO_WAIT_TIMES; i++) {
		udelay(2);
		val = ioread32(hw->hw_addr + REG_MDIO_CTRL);
		if (!(val & (MDIO_START | MDIO_BUSY)))
			break;
	}

	if (!(val & (MDIO_START | MDIO_BUSY)))
		return ATL1_SUCCESS;

	return ATL1_ERR_PHY;
}

/*
 * Make L001's PHY out of Power Saving State (bug)
 * hw - Struct containing variables accessed by shared code
 * when power on, L001's PHY always on Power saving State
 * (Gigabit Link forbidden)
 */
static s32 atl1_phy_leave_power_saving(struct atl1_hw *hw)
{
	s32 ret;
	ret = atl1_write_phy_reg(hw, 29, 0x0029);
	if (ret)
		return ret;
	return atl1_write_phy_reg(hw, 30, 0);
}

/*
 *TODO: do something or get rid of this
 */
s32 atl1_phy_enter_power_saving(struct atl1_hw *hw)
{
/*    s32 ret_val;
 *    u16 phy_data;
 */

/*
    ret_val = atl1_write_phy_reg(hw, ...);
    ret_val = atl1_write_phy_reg(hw, ...);
    ....
*/
	return ATL1_SUCCESS;
}

/*
 * Resets the PHY and make all config validate
 * hw - Struct containing variables accessed by shared code
 *
 * Sets bit 15 and 12 of the MII Control regiser (for F001 bug)
 */
static s32 atl1_phy_reset(struct atl1_hw *hw)
{
	struct pci_dev *pdev = hw->back->pdev;
	s32 ret_val;
	u16 phy_data;

	if (hw->media_type == MEDIA_TYPE_AUTO_SENSOR ||
	    hw->media_type == MEDIA_TYPE_1000M_FULL)
		phy_data = MII_CR_RESET | MII_CR_AUTO_NEG_EN;
	else {
		switch (hw->media_type) {
		case MEDIA_TYPE_100M_FULL:
			phy_data =
			    MII_CR_FULL_DUPLEX | MII_CR_SPEED_100 |
			    MII_CR_RESET;
			break;
		case MEDIA_TYPE_100M_HALF:
			phy_data = MII_CR_SPEED_100 | MII_CR_RESET;
			break;
		case MEDIA_TYPE_10M_FULL:
			phy_data =
			    MII_CR_FULL_DUPLEX | MII_CR_SPEED_10 | MII_CR_RESET;
			break;
		default:	/* MEDIA_TYPE_10M_HALF: */
			phy_data = MII_CR_SPEED_10 | MII_CR_RESET;
			break;
		}
	}

	ret_val = atl1_write_phy_reg(hw, MII_BMCR, phy_data);
	if (ret_val) {
		u32 val;
		int i;
		/* pcie serdes link may be down! */
		dev_dbg(&pdev->dev, "pcie phy link down\n");

		for (i = 0; i < 25; i++) {
			msleep(1);
			val = ioread32(hw->hw_addr + REG_MDIO_CTRL);
			if (!(val & (MDIO_START | MDIO_BUSY)))
				break;
		}

		if ((val & (MDIO_START | MDIO_BUSY)) != 0) {
			dev_warn(&pdev->dev, "pcie link down at least 25ms\n");
			return ret_val;
		}
	}
	return ATL1_SUCCESS;
}

/*
 * Configures PHY autoneg and flow control advertisement settings
 * hw - Struct containing variables accessed by shared code
 */
s32 atl1_phy_setup_autoneg_adv(struct atl1_hw *hw)
{
	s32 ret_val;
	s16 mii_autoneg_adv_reg;
	s16 mii_1000t_ctrl_reg;

	/* Read the MII Auto-Neg Advertisement Register (Address 4). */
	mii_autoneg_adv_reg = MII_AR_DEFAULT_CAP_MASK;

	/* Read the MII 1000Base-T Control Register (Address 9). */
	mii_1000t_ctrl_reg = MII_AT001_CR_1000T_DEFAULT_CAP_MASK;

	/*
	 * First we clear all the 10/100 mb speed bits in the Auto-Neg
	 * Advertisement Register (Address 4) and the 1000 mb speed bits in
	 * the  1000Base-T Control Register (Address 9).
	 */
	mii_autoneg_adv_reg &= ~MII_AR_SPEED_MASK;
	mii_1000t_ctrl_reg &= ~MII_AT001_CR_1000T_SPEED_MASK;

	/*
	 * Need to parse media_type  and set up
	 * the appropriate PHY registers.
	 */
	switch (hw->media_type) {
	case MEDIA_TYPE_AUTO_SENSOR:
		mii_autoneg_adv_reg |= (MII_AR_10T_HD_CAPS |
					MII_AR_10T_FD_CAPS |
					MII_AR_100TX_HD_CAPS |
					MII_AR_100TX_FD_CAPS);
		mii_1000t_ctrl_reg |= MII_AT001_CR_1000T_FD_CAPS;
		break;

	case MEDIA_TYPE_1000M_FULL:
		mii_1000t_ctrl_reg |= MII_AT001_CR_1000T_FD_CAPS;
		break;

	case MEDIA_TYPE_100M_FULL:
		mii_autoneg_adv_reg |= MII_AR_100TX_FD_CAPS;
		break;

	case MEDIA_TYPE_100M_HALF:
		mii_autoneg_adv_reg |= MII_AR_100TX_HD_CAPS;
		break;

	case MEDIA_TYPE_10M_FULL:
		mii_autoneg_adv_reg |= MII_AR_10T_FD_CAPS;
		break;

	default:
		mii_autoneg_adv_reg |= MII_AR_10T_HD_CAPS;
		break;
	}

	/* flow control fixed to enable all */
	mii_autoneg_adv_reg |= (MII_AR_ASM_DIR | MII_AR_PAUSE);

	hw->mii_autoneg_adv_reg = mii_autoneg_adv_reg;
	hw->mii_1000t_ctrl_reg = mii_1000t_ctrl_reg;

	ret_val = atl1_write_phy_reg(hw, MII_ADVERTISE, mii_autoneg_adv_reg);
	if (ret_val)
		return ret_val;

	ret_val = atl1_write_phy_reg(hw, MII_AT001_CR, mii_1000t_ctrl_reg);
	if (ret_val)
		return ret_val;

	return ATL1_SUCCESS;
}

/*
 * Configures link settings.
 * hw - Struct containing variables accessed by shared code
 * Assumes the hardware has previously been reset and the
 * transmitter and receiver are not enabled.
 */
static s32 atl1_setup_link(struct atl1_hw *hw)
{
	struct pci_dev *pdev = hw->back->pdev;
	s32 ret_val;

	/*
	 * Options:
	 *  PHY will advertise value(s) parsed from
	 *  autoneg_advertised and fc
	 *  no matter what autoneg is , We will not wait link result.
	 */
	ret_val = atl1_phy_setup_autoneg_adv(hw);
	if (ret_val) {
		dev_dbg(&pdev->dev, "error setting up autonegotiation\n");
		return ret_val;
	}
	/* SW.Reset , En-Auto-Neg if needed */
	ret_val = atl1_phy_reset(hw);
	if (ret_val) {
		dev_dbg(&pdev->dev, "error resetting phy\n");
		return ret_val;
	}
	hw->phy_configured = true;
	return ret_val;
}

static struct atl1_spi_flash_dev flash_table[] = {
/*	MFR_NAME  WRSR  READ  PRGM  WREN  WRDI  RDSR  RDID  SECTOR_ERASE CHIP_ERASE */
	{"Atmel", 0x00, 0x03, 0x02, 0x06, 0x04, 0x05, 0x15, 0x52,        0x62},
	{"SST",   0x01, 0x03, 0x02, 0x06, 0x04, 0x05, 0x90, 0x20,        0x60},
	{"ST",    0x01, 0x03, 0x02, 0x06, 0x04, 0x05, 0xAB, 0xD8,        0xC7},
};

static void atl1_init_flash_opcode(struct atl1_hw *hw)
{
	if (hw->flash_vendor >= ARRAY_SIZE(flash_table))
		hw->flash_vendor = 0;	/* ATMEL */

	/* Init OP table */
	iowrite8(flash_table[hw->flash_vendor].cmd_program,
		hw->hw_addr + REG_SPI_FLASH_OP_PROGRAM);
	iowrite8(flash_table[hw->flash_vendor].cmd_sector_erase,
		hw->hw_addr + REG_SPI_FLASH_OP_SC_ERASE);
	iowrite8(flash_table[hw->flash_vendor].cmd_chip_erase,
		hw->hw_addr + REG_SPI_FLASH_OP_CHIP_ERASE);
	iowrite8(flash_table[hw->flash_vendor].cmd_rdid,
		hw->hw_addr + REG_SPI_FLASH_OP_RDID);
	iowrite8(flash_table[hw->flash_vendor].cmd_wren,
		hw->hw_addr + REG_SPI_FLASH_OP_WREN);
	iowrite8(flash_table[hw->flash_vendor].cmd_rdsr,
		hw->hw_addr + REG_SPI_FLASH_OP_RDSR);
	iowrite8(flash_table[hw->flash_vendor].cmd_wrsr,
		hw->hw_addr + REG_SPI_FLASH_OP_WRSR);
	iowrite8(flash_table[hw->flash_vendor].cmd_read,
		hw->hw_addr + REG_SPI_FLASH_OP_READ);
}

/*
 * Performs basic configuration of the adapter.
 * hw - Struct containing variables accessed by shared code
 * Assumes that the controller has previously been reset and is in a
 * post-reset uninitialized state. Initializes multicast table,
 * and  Calls routines to setup link
 * Leaves the transmit and receive units disabled and uninitialized.
 */
s32 atl1_init_hw(struct atl1_hw *hw)
{
	u32 ret_val = 0;

	/* Zero out the Multicast HASH table */
	iowrite32(0, hw->hw_addr + REG_RX_HASH_TABLE);
	/* clear the old settings from the multicast hash table */
	iowrite32(0, (hw->hw_addr + REG_RX_HASH_TABLE) + (1 << 2));

	atl1_init_flash_opcode(hw);

	if (!hw->phy_configured) {
		/* enable GPHY LinkChange Interrrupt */
		ret_val = atl1_write_phy_reg(hw, 18, 0xC00);
		if (ret_val)
			return ret_val;
		/* make PHY out of power-saving state */
		ret_val = atl1_phy_leave_power_saving(hw);
		if (ret_val)
			return ret_val;
		/* Call a subroutine to configure the link */
		ret_val = atl1_setup_link(hw);
	}
	return ret_val;
}

/*
 * Detects the current speed and duplex settings of the hardware.
 * hw - Struct containing variables accessed by shared code
 * speed - Speed of the connection
 * duplex - Duplex setting of the connection
 */
s32 atl1_get_speed_and_duplex(struct atl1_hw *hw, u16 *speed, u16 *duplex)
{
	struct pci_dev *pdev = hw->back->pdev;
	s32 ret_val;
	u16 phy_data;

	/* ; --- Read   PHY Specific Status Register (17) */
	ret_val = atl1_read_phy_reg(hw, MII_AT001_PSSR, &phy_data);
	if (ret_val)
		return ret_val;

	if (!(phy_data & MII_AT001_PSSR_SPD_DPLX_RESOLVED))
		return ATL1_ERR_PHY_RES;

	switch (phy_data & MII_AT001_PSSR_SPEED) {
	case MII_AT001_PSSR_1000MBS:
		*speed = SPEED_1000;
		break;
	case MII_AT001_PSSR_100MBS:
		*speed = SPEED_100;
		break;
	case MII_AT001_PSSR_10MBS:
		*speed = SPEED_10;
		break;
	default:
		dev_dbg(&pdev->dev, "error getting speed\n");
		return ATL1_ERR_PHY_SPEED;
		break;
	}
	if (phy_data & MII_AT001_PSSR_DPLX)
		*duplex = FULL_DUPLEX;
	else
		*duplex = HALF_DUPLEX;

	return ATL1_SUCCESS;
}

void atl1_set_mac_addr(struct atl1_hw *hw)
{
	u32 value;
	/*
	 * 00-0B-6A-F6-00-DC
	 * 0:  6AF600DC   1: 000B
	 * low dword
	 */
	value = (((u32) hw->mac_addr[2]) << 24) |
	    (((u32) hw->mac_addr[3]) << 16) |
	    (((u32) hw->mac_addr[4]) << 8) | (((u32) hw->mac_addr[5]));
	iowrite32(value, hw->hw_addr + REG_MAC_STA_ADDR);
	/* high dword */
	value = (((u32) hw->mac_addr[0]) << 8) | (((u32) hw->mac_addr[1]));
	iowrite32(value, (hw->hw_addr + REG_MAC_STA_ADDR) + (1 << 2));
}