mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-17 01:26:57 +07:00
781f0766cc
Devices connected under Terminus Technology Inc. Hub (1a40:0101) may fail to work after the system resumes from suspend: [ 206.063325] usb 3-2.4: reset full-speed USB device number 4 using xhci_hcd [ 206.143691] usb 3-2.4: device descriptor read/64, error -32 [ 206.351671] usb 3-2.4: device descriptor read/64, error -32 Info for this hub: T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=480 MxCh= 4 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=1a40 ProdID=0101 Rev=01.11 S: Product=USB 2.0 Hub C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub Some expirements indicate that the USB devices connected to the hub are innocent, it's the hub itself is to blame. The hub needs extra delay time after it resets its port. Hence wait for extra delay, if the device is connected to this quirky hub. Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Cc: stable <stable@vger.kernel.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
73 lines
2.3 KiB
C
73 lines
2.3 KiB
C
/* SPDX-License-Identifier: GPL-2.0 */
|
|
/*
|
|
* This file holds the definitions of quirks found in USB devices.
|
|
* Only quirks that affect the whole device, not an interface,
|
|
* belong here.
|
|
*/
|
|
|
|
#ifndef __LINUX_USB_QUIRKS_H
|
|
#define __LINUX_USB_QUIRKS_H
|
|
|
|
/* string descriptors must not be fetched using a 255-byte read */
|
|
#define USB_QUIRK_STRING_FETCH_255 BIT(0)
|
|
|
|
/* device can't resume correctly so reset it instead */
|
|
#define USB_QUIRK_RESET_RESUME BIT(1)
|
|
|
|
/* device can't handle Set-Interface requests */
|
|
#define USB_QUIRK_NO_SET_INTF BIT(2)
|
|
|
|
/* device can't handle its Configuration or Interface strings */
|
|
#define USB_QUIRK_CONFIG_INTF_STRINGS BIT(3)
|
|
|
|
/* device can't be reset(e.g morph devices), don't use reset */
|
|
#define USB_QUIRK_RESET BIT(4)
|
|
|
|
/* device has more interface descriptions than the bNumInterfaces count,
|
|
and can't handle talking to these interfaces */
|
|
#define USB_QUIRK_HONOR_BNUMINTERFACES BIT(5)
|
|
|
|
/* device needs a pause during initialization, after we read the device
|
|
descriptor */
|
|
#define USB_QUIRK_DELAY_INIT BIT(6)
|
|
|
|
/*
|
|
* For high speed and super speed interupt endpoints, the USB 2.0 and
|
|
* USB 3.0 spec require the interval in microframes
|
|
* (1 microframe = 125 microseconds) to be calculated as
|
|
* interval = 2 ^ (bInterval-1).
|
|
*
|
|
* Devices with this quirk report their bInterval as the result of this
|
|
* calculation instead of the exponent variable used in the calculation.
|
|
*/
|
|
#define USB_QUIRK_LINEAR_UFRAME_INTR_BINTERVAL BIT(7)
|
|
|
|
/* device can't handle device_qualifier descriptor requests */
|
|
#define USB_QUIRK_DEVICE_QUALIFIER BIT(8)
|
|
|
|
/* device generates spurious wakeup, ignore remote wakeup capability */
|
|
#define USB_QUIRK_IGNORE_REMOTE_WAKEUP BIT(9)
|
|
|
|
/* device can't handle Link Power Management */
|
|
#define USB_QUIRK_NO_LPM BIT(10)
|
|
|
|
/*
|
|
* Device reports its bInterval as linear frames instead of the
|
|
* USB 2.0 calculation.
|
|
*/
|
|
#define USB_QUIRK_LINEAR_FRAME_INTR_BINTERVAL BIT(11)
|
|
|
|
/*
|
|
* Device needs to be disconnected before suspend to prevent spurious
|
|
* wakeup.
|
|
*/
|
|
#define USB_QUIRK_DISCONNECT_SUSPEND BIT(12)
|
|
|
|
/* Device needs a pause after every control message. */
|
|
#define USB_QUIRK_DELAY_CTRL_MSG BIT(13)
|
|
|
|
/* Hub needs extra delay after resetting its port. */
|
|
#define USB_QUIRK_HUB_SLOW_RESET BIT(14)
|
|
|
|
#endif /* __LINUX_USB_QUIRKS_H */
|