linux_dsm_epyc7002/drivers/net/ethernet/lantiq_xrx200.c
Hauke Mehrtens a44ecfbda4 net: lantiq: lantiq_xrx200: Move clock prepare to probe function
The switch and the MAC are in one IP core and they use the same clock
signal from the clock generation unit.
Currently the clock architecture in the lantiq SoC code does not allow
to easily share the same clocks, this has to be fixed by switching to
the common clock framework.
As a workaround the clock of the switch and MAC should be activated when
the MAC gets probed and only disabled when the MAC gets removed. This
way it is ensured that the clock is always enabled when the switch or
MAC is used. The switch can not be used without the MAC.

This fixes a data bus error when rebooting the system and deactivating
the switch and mac and later accessing some registers in the cleanup
while the clocks are disabled.

Fixes: fe1a56420c ("net: lantiq: Add Lantiq / Intel VRX200 Ethernet driver")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-17 08:12:11 -07:00

568 lines
13 KiB
C

// SPDX-License-Identifier: GPL-2.0
/*
* Lantiq / Intel PMAC driver for XRX200 SoCs
*
* Copyright (C) 2010 Lantiq Deutschland
* Copyright (C) 2012 John Crispin <john@phrozen.org>
* Copyright (C) 2017 - 2018 Hauke Mehrtens <hauke@hauke-m.de>
*/
#include <linux/etherdevice.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/interrupt.h>
#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/of_net.h>
#include <linux/of_platform.h>
#include <xway_dma.h>
/* DMA */
#define XRX200_DMA_DATA_LEN 0x600
#define XRX200_DMA_RX 0
#define XRX200_DMA_TX 1
/* cpu port mac */
#define PMAC_RX_IPG 0x0024
#define PMAC_RX_IPG_MASK 0xf
#define PMAC_HD_CTL 0x0000
/* Add Ethernet header to packets from DMA to PMAC */
#define PMAC_HD_CTL_ADD BIT(0)
/* Add VLAN tag to Packets from DMA to PMAC */
#define PMAC_HD_CTL_TAG BIT(1)
/* Add CRC to packets from DMA to PMAC */
#define PMAC_HD_CTL_AC BIT(2)
/* Add status header to packets from PMAC to DMA */
#define PMAC_HD_CTL_AS BIT(3)
/* Remove CRC from packets from PMAC to DMA */
#define PMAC_HD_CTL_RC BIT(4)
/* Remove Layer-2 header from packets from PMAC to DMA */
#define PMAC_HD_CTL_RL2 BIT(5)
/* Status header is present from DMA to PMAC */
#define PMAC_HD_CTL_RXSH BIT(6)
/* Add special tag from PMAC to switch */
#define PMAC_HD_CTL_AST BIT(7)
/* Remove specail Tag from PMAC to DMA */
#define PMAC_HD_CTL_RST BIT(8)
/* Check CRC from DMA to PMAC */
#define PMAC_HD_CTL_CCRC BIT(9)
/* Enable reaction to Pause frames in the PMAC */
#define PMAC_HD_CTL_FC BIT(10)
struct xrx200_chan {
int tx_free;
struct napi_struct napi;
struct ltq_dma_channel dma;
struct sk_buff *skb[LTQ_DESC_NUM];
struct xrx200_priv *priv;
};
struct xrx200_priv {
struct clk *clk;
struct xrx200_chan chan_tx;
struct xrx200_chan chan_rx;
struct net_device *net_dev;
struct device *dev;
__iomem void *pmac_reg;
};
static u32 xrx200_pmac_r32(struct xrx200_priv *priv, u32 offset)
{
return __raw_readl(priv->pmac_reg + offset);
}
static void xrx200_pmac_w32(struct xrx200_priv *priv, u32 val, u32 offset)
{
__raw_writel(val, priv->pmac_reg + offset);
}
static void xrx200_pmac_mask(struct xrx200_priv *priv, u32 clear, u32 set,
u32 offset)
{
u32 val = xrx200_pmac_r32(priv, offset);
val &= ~(clear);
val |= set;
xrx200_pmac_w32(priv, val, offset);
}
/* drop all the packets from the DMA ring */
static void xrx200_flush_dma(struct xrx200_chan *ch)
{
int i;
for (i = 0; i < LTQ_DESC_NUM; i++) {
struct ltq_dma_desc *desc = &ch->dma.desc_base[ch->dma.desc];
if ((desc->ctl & (LTQ_DMA_OWN | LTQ_DMA_C)) != LTQ_DMA_C)
break;
desc->ctl = LTQ_DMA_OWN | LTQ_DMA_RX_OFFSET(NET_IP_ALIGN) |
XRX200_DMA_DATA_LEN;
ch->dma.desc++;
ch->dma.desc %= LTQ_DESC_NUM;
}
}
static int xrx200_open(struct net_device *net_dev)
{
struct xrx200_priv *priv = netdev_priv(net_dev);
napi_enable(&priv->chan_tx.napi);
ltq_dma_open(&priv->chan_tx.dma);
ltq_dma_enable_irq(&priv->chan_tx.dma);
napi_enable(&priv->chan_rx.napi);
ltq_dma_open(&priv->chan_rx.dma);
/* The boot loader does not always deactivate the receiving of frames
* on the ports and then some packets queue up in the PPE buffers.
* They already passed the PMAC so they do not have the tags
* configured here. Read the these packets here and drop them.
* The HW should have written them into memory after 10us
*/
usleep_range(20, 40);
xrx200_flush_dma(&priv->chan_rx);
ltq_dma_enable_irq(&priv->chan_rx.dma);
netif_wake_queue(net_dev);
return 0;
}
static int xrx200_close(struct net_device *net_dev)
{
struct xrx200_priv *priv = netdev_priv(net_dev);
netif_stop_queue(net_dev);
napi_disable(&priv->chan_rx.napi);
ltq_dma_close(&priv->chan_rx.dma);
napi_disable(&priv->chan_tx.napi);
ltq_dma_close(&priv->chan_tx.dma);
return 0;
}
static int xrx200_alloc_skb(struct xrx200_chan *ch)
{
int ret = 0;
ch->skb[ch->dma.desc] = netdev_alloc_skb_ip_align(ch->priv->net_dev,
XRX200_DMA_DATA_LEN);
if (!ch->skb[ch->dma.desc]) {
ret = -ENOMEM;
goto skip;
}
ch->dma.desc_base[ch->dma.desc].addr = dma_map_single(ch->priv->dev,
ch->skb[ch->dma.desc]->data, XRX200_DMA_DATA_LEN,
DMA_FROM_DEVICE);
if (unlikely(dma_mapping_error(ch->priv->dev,
ch->dma.desc_base[ch->dma.desc].addr))) {
dev_kfree_skb_any(ch->skb[ch->dma.desc]);
ret = -ENOMEM;
goto skip;
}
skip:
ch->dma.desc_base[ch->dma.desc].ctl =
LTQ_DMA_OWN | LTQ_DMA_RX_OFFSET(NET_IP_ALIGN) |
XRX200_DMA_DATA_LEN;
return ret;
}
static int xrx200_hw_receive(struct xrx200_chan *ch)
{
struct xrx200_priv *priv = ch->priv;
struct ltq_dma_desc *desc = &ch->dma.desc_base[ch->dma.desc];
struct sk_buff *skb = ch->skb[ch->dma.desc];
int len = (desc->ctl & LTQ_DMA_SIZE_MASK);
struct net_device *net_dev = priv->net_dev;
int ret;
ret = xrx200_alloc_skb(ch);
ch->dma.desc++;
ch->dma.desc %= LTQ_DESC_NUM;
if (ret) {
netdev_err(net_dev, "failed to allocate new rx buffer\n");
return ret;
}
skb_put(skb, len);
skb->protocol = eth_type_trans(skb, net_dev);
netif_receive_skb(skb);
net_dev->stats.rx_packets++;
net_dev->stats.rx_bytes += len - ETH_FCS_LEN;
return 0;
}
static int xrx200_poll_rx(struct napi_struct *napi, int budget)
{
struct xrx200_chan *ch = container_of(napi,
struct xrx200_chan, napi);
int rx = 0;
int ret;
while (rx < budget) {
struct ltq_dma_desc *desc = &ch->dma.desc_base[ch->dma.desc];
if ((desc->ctl & (LTQ_DMA_OWN | LTQ_DMA_C)) == LTQ_DMA_C) {
ret = xrx200_hw_receive(ch);
if (ret)
return ret;
rx++;
} else {
break;
}
}
if (rx < budget) {
napi_complete(&ch->napi);
ltq_dma_enable_irq(&ch->dma);
}
return rx;
}
static int xrx200_tx_housekeeping(struct napi_struct *napi, int budget)
{
struct xrx200_chan *ch = container_of(napi,
struct xrx200_chan, napi);
struct net_device *net_dev = ch->priv->net_dev;
int pkts = 0;
int bytes = 0;
while (pkts < budget) {
struct ltq_dma_desc *desc = &ch->dma.desc_base[ch->tx_free];
if ((desc->ctl & (LTQ_DMA_OWN | LTQ_DMA_C)) == LTQ_DMA_C) {
struct sk_buff *skb = ch->skb[ch->tx_free];
pkts++;
bytes += skb->len;
ch->skb[ch->tx_free] = NULL;
consume_skb(skb);
memset(&ch->dma.desc_base[ch->tx_free], 0,
sizeof(struct ltq_dma_desc));
ch->tx_free++;
ch->tx_free %= LTQ_DESC_NUM;
} else {
break;
}
}
net_dev->stats.tx_packets += pkts;
net_dev->stats.tx_bytes += bytes;
netdev_completed_queue(ch->priv->net_dev, pkts, bytes);
if (pkts < budget) {
napi_complete(&ch->napi);
ltq_dma_enable_irq(&ch->dma);
}
return pkts;
}
static int xrx200_start_xmit(struct sk_buff *skb, struct net_device *net_dev)
{
struct xrx200_priv *priv = netdev_priv(net_dev);
struct xrx200_chan *ch = &priv->chan_tx;
struct ltq_dma_desc *desc = &ch->dma.desc_base[ch->dma.desc];
u32 byte_offset;
dma_addr_t mapping;
int len;
skb->dev = net_dev;
if (skb_put_padto(skb, ETH_ZLEN)) {
net_dev->stats.tx_dropped++;
return NETDEV_TX_OK;
}
len = skb->len;
if ((desc->ctl & (LTQ_DMA_OWN | LTQ_DMA_C)) || ch->skb[ch->dma.desc]) {
netdev_err(net_dev, "tx ring full\n");
netif_stop_queue(net_dev);
return NETDEV_TX_BUSY;
}
ch->skb[ch->dma.desc] = skb;
mapping = dma_map_single(priv->dev, skb->data, len, DMA_TO_DEVICE);
if (unlikely(dma_mapping_error(priv->dev, mapping)))
goto err_drop;
/* dma needs to start on a 16 byte aligned address */
byte_offset = mapping % 16;
desc->addr = mapping - byte_offset;
/* Make sure the address is written before we give it to HW */
wmb();
desc->ctl = LTQ_DMA_OWN | LTQ_DMA_SOP | LTQ_DMA_EOP |
LTQ_DMA_TX_OFFSET(byte_offset) | (len & LTQ_DMA_SIZE_MASK);
ch->dma.desc++;
ch->dma.desc %= LTQ_DESC_NUM;
if (ch->dma.desc == ch->tx_free)
netif_stop_queue(net_dev);
netdev_sent_queue(net_dev, len);
return NETDEV_TX_OK;
err_drop:
dev_kfree_skb(skb);
net_dev->stats.tx_dropped++;
net_dev->stats.tx_errors++;
return NETDEV_TX_OK;
}
static const struct net_device_ops xrx200_netdev_ops = {
.ndo_open = xrx200_open,
.ndo_stop = xrx200_close,
.ndo_start_xmit = xrx200_start_xmit,
.ndo_set_mac_address = eth_mac_addr,
.ndo_validate_addr = eth_validate_addr,
.ndo_change_mtu = eth_change_mtu,
};
static irqreturn_t xrx200_dma_irq(int irq, void *ptr)
{
struct xrx200_chan *ch = ptr;
ltq_dma_disable_irq(&ch->dma);
ltq_dma_ack_irq(&ch->dma);
napi_schedule(&ch->napi);
return IRQ_HANDLED;
}
static int xrx200_dma_init(struct xrx200_priv *priv)
{
struct xrx200_chan *ch_rx = &priv->chan_rx;
struct xrx200_chan *ch_tx = &priv->chan_tx;
int ret = 0;
int i;
ltq_dma_init_port(DMA_PORT_ETOP);
ch_rx->dma.nr = XRX200_DMA_RX;
ch_rx->dma.dev = priv->dev;
ch_rx->priv = priv;
ltq_dma_alloc_rx(&ch_rx->dma);
for (ch_rx->dma.desc = 0; ch_rx->dma.desc < LTQ_DESC_NUM;
ch_rx->dma.desc++) {
ret = xrx200_alloc_skb(ch_rx);
if (ret)
goto rx_free;
}
ch_rx->dma.desc = 0;
ret = devm_request_irq(priv->dev, ch_rx->dma.irq, xrx200_dma_irq, 0,
"xrx200_net_rx", &priv->chan_rx);
if (ret) {
dev_err(priv->dev, "failed to request RX irq %d\n",
ch_rx->dma.irq);
goto rx_ring_free;
}
ch_tx->dma.nr = XRX200_DMA_TX;
ch_tx->dma.dev = priv->dev;
ch_tx->priv = priv;
ltq_dma_alloc_tx(&ch_tx->dma);
ret = devm_request_irq(priv->dev, ch_tx->dma.irq, xrx200_dma_irq, 0,
"xrx200_net_tx", &priv->chan_tx);
if (ret) {
dev_err(priv->dev, "failed to request TX irq %d\n",
ch_tx->dma.irq);
goto tx_free;
}
return ret;
tx_free:
ltq_dma_free(&ch_tx->dma);
rx_ring_free:
/* free the allocated RX ring */
for (i = 0; i < LTQ_DESC_NUM; i++) {
if (priv->chan_rx.skb[i])
dev_kfree_skb_any(priv->chan_rx.skb[i]);
}
rx_free:
ltq_dma_free(&ch_rx->dma);
return ret;
}
static void xrx200_hw_cleanup(struct xrx200_priv *priv)
{
int i;
ltq_dma_free(&priv->chan_tx.dma);
ltq_dma_free(&priv->chan_rx.dma);
/* free the allocated RX ring */
for (i = 0; i < LTQ_DESC_NUM; i++)
dev_kfree_skb_any(priv->chan_rx.skb[i]);
}
static int xrx200_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
struct device_node *np = dev->of_node;
struct resource *res;
struct xrx200_priv *priv;
struct net_device *net_dev;
const u8 *mac;
int err;
/* alloc the network device */
net_dev = devm_alloc_etherdev(dev, sizeof(struct xrx200_priv));
if (!net_dev)
return -ENOMEM;
priv = netdev_priv(net_dev);
priv->net_dev = net_dev;
priv->dev = dev;
net_dev->netdev_ops = &xrx200_netdev_ops;
SET_NETDEV_DEV(net_dev, dev);
net_dev->min_mtu = ETH_ZLEN;
net_dev->max_mtu = XRX200_DMA_DATA_LEN;
/* load the memory ranges */
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!res) {
dev_err(dev, "failed to get resources\n");
return -ENOENT;
}
priv->pmac_reg = devm_ioremap_resource(dev, res);
if (IS_ERR(priv->pmac_reg)) {
dev_err(dev, "failed to request and remap io ranges\n");
return PTR_ERR(priv->pmac_reg);
}
priv->chan_rx.dma.irq = platform_get_irq_byname(pdev, "rx");
if (priv->chan_rx.dma.irq < 0) {
dev_err(dev, "failed to get RX IRQ, %i\n",
priv->chan_rx.dma.irq);
return -ENOENT;
}
priv->chan_tx.dma.irq = platform_get_irq_byname(pdev, "tx");
if (priv->chan_tx.dma.irq < 0) {
dev_err(dev, "failed to get TX IRQ, %i\n",
priv->chan_tx.dma.irq);
return -ENOENT;
}
/* get the clock */
priv->clk = devm_clk_get(dev, NULL);
if (IS_ERR(priv->clk)) {
dev_err(dev, "failed to get clock\n");
return PTR_ERR(priv->clk);
}
mac = of_get_mac_address(np);
if (mac && is_valid_ether_addr(mac))
ether_addr_copy(net_dev->dev_addr, mac);
else
eth_hw_addr_random(net_dev);
/* bring up the dma engine and IP core */
err = xrx200_dma_init(priv);
if (err)
return err;
/* enable clock gate */
err = clk_prepare_enable(priv->clk);
if (err)
goto err_uninit_dma;
/* set IPG to 12 */
xrx200_pmac_mask(priv, PMAC_RX_IPG_MASK, 0xb, PMAC_RX_IPG);
/* enable status header, enable CRC */
xrx200_pmac_mask(priv, 0,
PMAC_HD_CTL_RST | PMAC_HD_CTL_AST | PMAC_HD_CTL_RXSH |
PMAC_HD_CTL_AS | PMAC_HD_CTL_AC | PMAC_HD_CTL_RC,
PMAC_HD_CTL);
/* setup NAPI */
netif_napi_add(net_dev, &priv->chan_rx.napi, xrx200_poll_rx, 32);
netif_napi_add(net_dev, &priv->chan_tx.napi, xrx200_tx_housekeeping, 32);
platform_set_drvdata(pdev, priv);
err = register_netdev(net_dev);
if (err)
goto err_unprepare_clk;
return err;
err_unprepare_clk:
clk_disable_unprepare(priv->clk);
err_uninit_dma:
xrx200_hw_cleanup(priv);
return 0;
}
static int xrx200_remove(struct platform_device *pdev)
{
struct xrx200_priv *priv = platform_get_drvdata(pdev);
struct net_device *net_dev = priv->net_dev;
/* free stack related instances */
netif_stop_queue(net_dev);
netif_napi_del(&priv->chan_tx.napi);
netif_napi_del(&priv->chan_rx.napi);
/* remove the actual device */
unregister_netdev(net_dev);
/* release the clock */
clk_disable_unprepare(priv->clk);
/* shut down hardware */
xrx200_hw_cleanup(priv);
return 0;
}
static const struct of_device_id xrx200_match[] = {
{ .compatible = "lantiq,xrx200-net" },
{},
};
MODULE_DEVICE_TABLE(of, xrx200_match);
static struct platform_driver xrx200_driver = {
.probe = xrx200_probe,
.remove = xrx200_remove,
.driver = {
.name = "lantiq,xrx200-net",
.of_match_table = xrx200_match,
},
};
module_platform_driver(xrx200_driver);
MODULE_AUTHOR("John Crispin <john@phrozen.org>");
MODULE_DESCRIPTION("Lantiq SoC XRX200 ethernet");
MODULE_LICENSE("GPL");