mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-06 21:16:39 +07:00
68f20d948c
- Update the Intel Wired LAN documentation with the latest URL for ethtool. - replace "Ethtool" with "ethtool" Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
261 lines
10 KiB
Plaintext
261 lines
10 KiB
Plaintext
Linux Base Driver for 10 Gigabit PCI Express Intel(R) Network Connection
|
|
========================================================================
|
|
|
|
Intel Gigabit Linux driver.
|
|
Copyright(c) 1999 - 2010 Intel Corporation.
|
|
|
|
Contents
|
|
========
|
|
|
|
- Identifying Your Adapter
|
|
- Additional Configurations
|
|
- Performance Tuning
|
|
- Known Issues
|
|
- Support
|
|
|
|
Identifying Your Adapter
|
|
========================
|
|
|
|
The driver in this release is compatible with 82598 and 82599-based Intel
|
|
Network Connections.
|
|
|
|
For more information on how to identify your adapter, go to the Adapter &
|
|
Driver ID Guide at:
|
|
|
|
http://support.intel.com/support/network/sb/CS-012904.htm
|
|
|
|
SFP+ Devices with Pluggable Optics
|
|
----------------------------------
|
|
|
|
82599-BASED ADAPTERS
|
|
|
|
NOTES: If your 82599-based Intel(R) Network Adapter came with Intel optics, or
|
|
is an Intel(R) Ethernet Server Adapter X520-2, then it only supports Intel
|
|
optics and/or the direct attach cables listed below.
|
|
|
|
When 82599-based SFP+ devices are connected back to back, they should be set to
|
|
the same Speed setting via ethtool. Results may vary if you mix speed settings.
|
|
82598-based adapters support all passive direct attach cables that comply
|
|
with SFF-8431 v4.1 and SFF-8472 v10.4 specifications. Active direct attach
|
|
cables are not supported.
|
|
|
|
Supplier Type Part Numbers
|
|
|
|
SR Modules
|
|
Intel DUAL RATE 1G/10G SFP+ SR (bailed) FTLX8571D3BCV-IT
|
|
Intel DUAL RATE 1G/10G SFP+ SR (bailed) AFBR-703SDDZ-IN1
|
|
Intel DUAL RATE 1G/10G SFP+ SR (bailed) AFBR-703SDZ-IN2
|
|
LR Modules
|
|
Intel DUAL RATE 1G/10G SFP+ LR (bailed) FTLX1471D3BCV-IT
|
|
Intel DUAL RATE 1G/10G SFP+ LR (bailed) AFCT-701SDDZ-IN1
|
|
Intel DUAL RATE 1G/10G SFP+ LR (bailed) AFCT-701SDZ-IN2
|
|
|
|
The following is a list of 3rd party SFP+ modules and direct attach cables that
|
|
have received some testing. Not all modules are applicable to all devices.
|
|
|
|
Supplier Type Part Numbers
|
|
|
|
Finisar SFP+ SR bailed, 10g single rate FTLX8571D3BCL
|
|
Avago SFP+ SR bailed, 10g single rate AFBR-700SDZ
|
|
Finisar SFP+ LR bailed, 10g single rate FTLX1471D3BCL
|
|
|
|
Finisar DUAL RATE 1G/10G SFP+ SR (No Bail) FTLX8571D3QCV-IT
|
|
Avago DUAL RATE 1G/10G SFP+ SR (No Bail) AFBR-703SDZ-IN1
|
|
Finisar DUAL RATE 1G/10G SFP+ LR (No Bail) FTLX1471D3QCV-IT
|
|
Avago DUAL RATE 1G/10G SFP+ LR (No Bail) AFCT-701SDZ-IN1
|
|
Finistar 1000BASE-T SFP FCLF8522P2BTL
|
|
Avago 1000BASE-T SFP ABCU-5710RZ
|
|
|
|
82599-based adapters support all passive and active limiting direct attach
|
|
cables that comply with SFF-8431 v4.1 and SFF-8472 v10.4 specifications.
|
|
|
|
Laser turns off for SFP+ when ifconfig down
|
|
-------------------------------------------
|
|
"ifconfig down" turns off the laser for 82599-based SFP+ fiber adapters.
|
|
"ifconfig up" turns on the later.
|
|
|
|
|
|
82598-BASED ADAPTERS
|
|
|
|
NOTES for 82598-Based Adapters:
|
|
- Intel(R) Network Adapters that support removable optical modules only support
|
|
their original module type (i.e., the Intel(R) 10 Gigabit SR Dual Port
|
|
Express Module only supports SR optical modules). If you plug in a different
|
|
type of module, the driver will not load.
|
|
- Hot Swapping/hot plugging optical modules is not supported.
|
|
- Only single speed, 10 gigabit modules are supported.
|
|
- LAN on Motherboard (LOMs) may support DA, SR, or LR modules. Other module
|
|
types are not supported. Please see your system documentation for details.
|
|
|
|
The following is a list of 3rd party SFP+ modules and direct attach cables that
|
|
have received some testing. Not all modules are applicable to all devices.
|
|
|
|
Supplier Type Part Numbers
|
|
|
|
Finisar SFP+ SR bailed, 10g single rate FTLX8571D3BCL
|
|
Avago SFP+ SR bailed, 10g single rate AFBR-700SDZ
|
|
Finisar SFP+ LR bailed, 10g single rate FTLX1471D3BCL
|
|
|
|
82598-based adapters support all passive direct attach cables that comply
|
|
with SFF-8431 v4.1 and SFF-8472 v10.4 specifications. Active direct attach
|
|
cables are not supported.
|
|
|
|
|
|
Flow Control
|
|
------------
|
|
Ethernet Flow Control (IEEE 802.3x) can be configured with ethtool to enable
|
|
receiving and transmitting pause frames for ixgbe. When TX is enabled, PAUSE
|
|
frames are generated when the receive packet buffer crosses a predefined
|
|
threshold. When rx is enabled, the transmit unit will halt for the time delay
|
|
specified when a PAUSE frame is received.
|
|
|
|
Flow Control is enabled by default. If you want to disable a flow control
|
|
capable link partner, use ethtool:
|
|
|
|
ethtool -A eth? autoneg off RX off TX off
|
|
|
|
NOTE: For 82598 backplane cards entering 1 gig mode, flow control default
|
|
behavior is changed to off. Flow control in 1 gig mode on these devices can
|
|
lead to Tx hangs.
|
|
|
|
Additional Configurations
|
|
=========================
|
|
|
|
Jumbo Frames
|
|
------------
|
|
The driver supports Jumbo Frames for all adapters. Jumbo Frames support is
|
|
enabled by changing the MTU to a value larger than the default of 1500.
|
|
The maximum value for the MTU is 16110. Use the ifconfig command to
|
|
increase the MTU size. For example:
|
|
|
|
ifconfig ethx mtu 9000 up
|
|
|
|
The maximum MTU setting for Jumbo Frames is 16110. This value coincides
|
|
with the maximum Jumbo Frames size of 16128.
|
|
|
|
Generic Receive Offload, aka GRO
|
|
--------------------------------
|
|
The driver supports the in-kernel software implementation of GRO. GRO has
|
|
shown that by coalescing Rx traffic into larger chunks of data, CPU
|
|
utilization can be significantly reduced when under large Rx load. GRO is an
|
|
evolution of the previously-used LRO interface. GRO is able to coalesce
|
|
other protocols besides TCP. It's also safe to use with configurations that
|
|
are problematic for LRO, namely bridging and iSCSI.
|
|
|
|
Data Center Bridging, aka DCB
|
|
-----------------------------
|
|
DCB is a configuration Quality of Service implementation in hardware.
|
|
It uses the VLAN priority tag (802.1p) to filter traffic. That means
|
|
that there are 8 different priorities that traffic can be filtered into.
|
|
It also enables priority flow control which can limit or eliminate the
|
|
number of dropped packets during network stress. Bandwidth can be
|
|
allocated to each of these priorities, which is enforced at the hardware
|
|
level.
|
|
|
|
To enable DCB support in ixgbe, you must enable the DCB netlink layer to
|
|
allow the userspace tools (see below) to communicate with the driver.
|
|
This can be found in the kernel configuration here:
|
|
|
|
-> Networking support
|
|
-> Networking options
|
|
-> Data Center Bridging support
|
|
|
|
Once this is selected, DCB support must be selected for ixgbe. This can
|
|
be found here:
|
|
|
|
-> Device Drivers
|
|
-> Network device support (NETDEVICES [=y])
|
|
-> Ethernet (10000 Mbit) (NETDEV_10000 [=y])
|
|
-> Intel(R) 10GbE PCI Express adapters support
|
|
-> Data Center Bridging (DCB) Support
|
|
|
|
After these options are selected, you must rebuild your kernel and your
|
|
modules.
|
|
|
|
In order to use DCB, userspace tools must be downloaded and installed.
|
|
The dcbd tools can be found at:
|
|
|
|
http://e1000.sf.net
|
|
|
|
Ethtool
|
|
-------
|
|
The driver utilizes the ethtool interface for driver configuration and
|
|
diagnostics, as well as displaying statistical information. The latest
|
|
ethtool version is required for this functionality.
|
|
|
|
The latest release of ethtool can be found from
|
|
http://ftp.kernel.org/pub/software/network/ethtool/
|
|
|
|
FCoE
|
|
----
|
|
This release of the ixgbe driver contains new code to enable users to use
|
|
Fiber Channel over Ethernet (FCoE) and Data Center Bridging (DCB)
|
|
functionality that is supported by the 82598-based hardware. This code has
|
|
no default effect on the regular driver operation, and configuring DCB and
|
|
FCoE is outside the scope of this driver README. Refer to
|
|
http://www.open-fcoe.org/ for FCoE project information and contact
|
|
e1000-eedc@lists.sourceforge.net for DCB information.
|
|
|
|
MAC and VLAN anti-spoofing feature
|
|
----------------------------------
|
|
When a malicious driver attempts to send a spoofed packet, it is dropped by
|
|
the hardware and not transmitted. An interrupt is sent to the PF driver
|
|
notifying it of the spoof attempt.
|
|
|
|
When a spoofed packet is detected the PF driver will send the following
|
|
message to the system log (displayed by the "dmesg" command):
|
|
|
|
Spoof event(s) detected on VF (n)
|
|
|
|
Where n=the VF that attempted to do the spoofing.
|
|
|
|
|
|
Performance Tuning
|
|
==================
|
|
|
|
An excellent article on performance tuning can be found at:
|
|
|
|
http://www.redhat.com/promo/summit/2008/downloads/pdf/Thursday/Mark_Wagner.pdf
|
|
|
|
|
|
Known Issues
|
|
============
|
|
|
|
Enabling SR-IOV in a 32-bit Microsoft* Windows* Server 2008 Guest OS using
|
|
Intel (R) 82576-based GbE or Intel (R) 82599-based 10GbE controller under KVM
|
|
-----------------------------------------------------------------------------
|
|
KVM Hypervisor/VMM supports direct assignment of a PCIe device to a VM. This
|
|
includes traditional PCIe devices, as well as SR-IOV-capable devices using
|
|
Intel 82576-based and 82599-based controllers.
|
|
|
|
While direct assignment of a PCIe device or an SR-IOV Virtual Function (VF)
|
|
to a Linux-based VM running 2.6.32 or later kernel works fine, there is a
|
|
known issue with Microsoft Windows Server 2008 VM that results in a "yellow
|
|
bang" error. This problem is within the KVM VMM itself, not the Intel driver,
|
|
or the SR-IOV logic of the VMM, but rather that KVM emulates an older CPU
|
|
model for the guests, and this older CPU model does not support MSI-X
|
|
interrupts, which is a requirement for Intel SR-IOV.
|
|
|
|
If you wish to use the Intel 82576 or 82599-based controllers in SR-IOV mode
|
|
with KVM and a Microsoft Windows Server 2008 guest try the following
|
|
workaround. The workaround is to tell KVM to emulate a different model of CPU
|
|
when using qemu to create the KVM guest:
|
|
|
|
"-cpu qemu64,model=13"
|
|
|
|
|
|
Support
|
|
=======
|
|
|
|
For general information, go to the Intel support website at:
|
|
|
|
http://support.intel.com
|
|
|
|
or the Intel Wired Networking project hosted by Sourceforge at:
|
|
|
|
http://e1000.sourceforge.net
|
|
|
|
If an issue is identified with the released source code on the supported
|
|
kernel with a supported adapter, email the specific information related
|
|
to the issue to e1000-devel@lists.sf.net
|