mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-05 07:16:56 +07:00
55985e15b8
Slow down the I2C clock speed on M28 and SPS1 as it turns out the I2C block in i.MX28 can not operate stable enough with the bus running at 400kHz. Note that the driver used by Freescale runs the bus at 250kHz when 400kHz speed is selected, but the mainline Linux kernel runs the bus at actual 400kHz and that's where it is occasionally unstable. Play safe and run the bus at 100kHz. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
169 lines
3.3 KiB
Plaintext
169 lines
3.3 KiB
Plaintext
/*
|
|
* Copyright (C) 2012 Marek Vasut <marex@denx.de>
|
|
*
|
|
* The code contained herein is licensed under the GNU General Public
|
|
* License. You may obtain a copy of the GNU General Public License
|
|
* Version 2 or later at the following locations:
|
|
*
|
|
* http://www.opensource.org/licenses/gpl-license.html
|
|
* http://www.gnu.org/copyleft/gpl.html
|
|
*/
|
|
|
|
/dts-v1/;
|
|
/include/ "imx28.dtsi"
|
|
|
|
/ {
|
|
model = "SchulerControl GmbH, SC SPS 1";
|
|
compatible = "schulercontrol,imx28-sps1", "fsl,imx28";
|
|
|
|
memory {
|
|
reg = <0x40000000 0x08000000>;
|
|
};
|
|
|
|
apb@80000000 {
|
|
apbh@80000000 {
|
|
pinctrl@80018000 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&hog_pins_a>;
|
|
|
|
hog_pins_a: hog-gpios@0 {
|
|
reg = <0>;
|
|
fsl,pinmux-ids = <
|
|
0x0003 /* MX28_PAD_GPMI_D00__GPIO_0_0 */
|
|
0x0033 /* MX28_PAD_GPMI_D03__GPIO_0_3 */
|
|
0x0063 /* MX28_PAD_GPMI_D06__GPIO_0_6 */
|
|
>;
|
|
fsl,drive-strength = <0>;
|
|
fsl,voltage = <1>;
|
|
fsl,pull-up = <0>;
|
|
};
|
|
|
|
};
|
|
|
|
ssp0: ssp@80010000 {
|
|
compatible = "fsl,imx28-mmc";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&mmc0_4bit_pins_a>;
|
|
bus-width = <4>;
|
|
status = "okay";
|
|
};
|
|
|
|
ssp2: ssp@80014000 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
compatible = "fsl,imx28-spi";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&spi2_pins_a>;
|
|
status = "okay";
|
|
|
|
flash: m25p80@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "everspin,mr25h256", "mr25h256";
|
|
spi-max-frequency = <40000000>;
|
|
reg = <0>;
|
|
};
|
|
};
|
|
};
|
|
|
|
apbx@80040000 {
|
|
i2c0: i2c@80058000 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&i2c0_pins_a>;
|
|
status = "okay";
|
|
|
|
rtc: rtc@51 {
|
|
compatible = "nxp,pcf8563";
|
|
reg = <0x51>;
|
|
};
|
|
|
|
eeprom: eeprom@52 {
|
|
compatible = "atmel,24c64";
|
|
reg = <0x52>;
|
|
pagesize = <32>;
|
|
};
|
|
};
|
|
|
|
duart: serial@80074000 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&duart_pins_a>;
|
|
status = "okay";
|
|
};
|
|
|
|
usbphy0: usbphy@8007c000 {
|
|
status = "okay";
|
|
};
|
|
|
|
auart0: serial@8006a000 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&auart0_pins_a>;
|
|
status = "okay";
|
|
};
|
|
};
|
|
};
|
|
|
|
ahb@80080000 {
|
|
usb0: usb@80080000 {
|
|
vbus-supply = <®_usb0_vbus>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&usbphy0_pins_b>;
|
|
status = "okay";
|
|
};
|
|
|
|
mac0: ethernet@800f0000 {
|
|
phy-mode = "rmii";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&mac0_pins_a>;
|
|
status = "okay";
|
|
};
|
|
|
|
mac1: ethernet@800f4000 {
|
|
phy-mode = "rmii";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&mac1_pins_a>;
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
regulators {
|
|
compatible = "simple-bus";
|
|
|
|
reg_usb0_vbus: usb0_vbus {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "usb0_vbus";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
gpio = <&gpio3 9 0>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
compatible = "gpio-leds";
|
|
status = "okay";
|
|
|
|
led@1 {
|
|
label = "sps1-1:yellow:user";
|
|
gpios = <&gpio0 6 0>;
|
|
linux,default-trigger = "heartbeat";
|
|
reg = <0>;
|
|
};
|
|
|
|
led@2 {
|
|
label = "sps1-2:red:user";
|
|
gpios = <&gpio0 3 0>;
|
|
linux,default-trigger = "heartbeat";
|
|
reg = <1>;
|
|
};
|
|
|
|
led@3 {
|
|
label = "sps1-3:red:user";
|
|
gpios = <&gpio0 0 0>;
|
|
default-trigger = "heartbeat";
|
|
reg = <2>;
|
|
};
|
|
|
|
};
|
|
};
|