mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-06 02:06:40 +07:00
58eb8cd565
This patch fixes host drivers to use CONFIG_PM_SLEEP instead of CONFIG_PM where applicable. Benefits of this change: * unused code is not being compiled in for CONFIG_PM=y, CONFIG_PM_SLEEP=n and CONFIG_PM_RUNTIME=y configurations * easier transition to use struct dev_pm_ops and SIMPLE_DEV_PM_OPS() in the future * more consistent code (there are host drivers which are using the correct CONFIG_PM_SLEEP checks already) The patch leaves the core libata code and ->port_[suspend,resume] support in sata_[inic162x,nv,sil24].c alone for now. Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Tejun Heo <tj@kernel.org>
456 lines
12 KiB
C
456 lines
12 KiB
C
/*
|
|
* pata_optidma.c - Opti DMA PATA for new ATA layer
|
|
* (C) 2006 Red Hat Inc
|
|
*
|
|
* The Opti DMA controllers are related to the older PIO PCI controllers
|
|
* and indeed the VLB ones. The main differences are that the timing
|
|
* numbers are now based off PCI clocks not VLB and differ, and that
|
|
* MWDMA is supported.
|
|
*
|
|
* This driver should support Viper-N+, FireStar, FireStar Plus.
|
|
*
|
|
* These devices support virtual DMA for read (aka the CS5520). Later
|
|
* chips support UDMA33, but only if the rest of the board logic does,
|
|
* so you have to get this right. We don't support the virtual DMA
|
|
* but we do handle UDMA.
|
|
*
|
|
* Bits that are worth knowing
|
|
* Most control registers are shadowed into I/O registers
|
|
* 0x1F5 bit 0 tells you if the PCI/VLB clock is 33 or 25Mhz
|
|
* Virtual DMA registers *move* between rev 0x02 and rev 0x10
|
|
* UDMA requires a 66MHz FSB
|
|
*
|
|
*/
|
|
|
|
#include <linux/kernel.h>
|
|
#include <linux/module.h>
|
|
#include <linux/pci.h>
|
|
#include <linux/blkdev.h>
|
|
#include <linux/delay.h>
|
|
#include <scsi/scsi_host.h>
|
|
#include <linux/libata.h>
|
|
|
|
#define DRV_NAME "pata_optidma"
|
|
#define DRV_VERSION "0.3.2"
|
|
|
|
enum {
|
|
READ_REG = 0, /* index of Read cycle timing register */
|
|
WRITE_REG = 1, /* index of Write cycle timing register */
|
|
CNTRL_REG = 3, /* index of Control register */
|
|
STRAP_REG = 5, /* index of Strap register */
|
|
MISC_REG = 6 /* index of Miscellaneous register */
|
|
};
|
|
|
|
static int pci_clock; /* 0 = 33 1 = 25 */
|
|
|
|
/**
|
|
* optidma_pre_reset - probe begin
|
|
* @link: ATA link
|
|
* @deadline: deadline jiffies for the operation
|
|
*
|
|
* Set up cable type and use generic probe init
|
|
*/
|
|
|
|
static int optidma_pre_reset(struct ata_link *link, unsigned long deadline)
|
|
{
|
|
struct ata_port *ap = link->ap;
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
static const struct pci_bits optidma_enable_bits = {
|
|
0x40, 1, 0x08, 0x00
|
|
};
|
|
|
|
if (ap->port_no && !pci_test_config_bits(pdev, &optidma_enable_bits))
|
|
return -ENOENT;
|
|
|
|
return ata_sff_prereset(link, deadline);
|
|
}
|
|
|
|
/**
|
|
* optidma_unlock - unlock control registers
|
|
* @ap: ATA port
|
|
*
|
|
* Unlock the control register block for this adapter. Registers must not
|
|
* be unlocked in a situation where libata might look at them.
|
|
*/
|
|
|
|
static void optidma_unlock(struct ata_port *ap)
|
|
{
|
|
void __iomem *regio = ap->ioaddr.cmd_addr;
|
|
|
|
/* These 3 unlock the control register access */
|
|
ioread16(regio + 1);
|
|
ioread16(regio + 1);
|
|
iowrite8(3, regio + 2);
|
|
}
|
|
|
|
/**
|
|
* optidma_lock - issue temporary relock
|
|
* @ap: ATA port
|
|
*
|
|
* Re-lock the configuration register settings.
|
|
*/
|
|
|
|
static void optidma_lock(struct ata_port *ap)
|
|
{
|
|
void __iomem *regio = ap->ioaddr.cmd_addr;
|
|
|
|
/* Relock */
|
|
iowrite8(0x83, regio + 2);
|
|
}
|
|
|
|
/**
|
|
* optidma_mode_setup - set mode data
|
|
* @ap: ATA interface
|
|
* @adev: ATA device
|
|
* @mode: Mode to set
|
|
*
|
|
* Called to do the DMA or PIO mode setup. Timing numbers are all
|
|
* pre computed to keep the code clean. There are two tables depending
|
|
* on the hardware clock speed.
|
|
*
|
|
* WARNING: While we do this the IDE registers vanish. If we take an
|
|
* IRQ here we depend on the host set locking to avoid catastrophe.
|
|
*/
|
|
|
|
static void optidma_mode_setup(struct ata_port *ap, struct ata_device *adev, u8 mode)
|
|
{
|
|
struct ata_device *pair = ata_dev_pair(adev);
|
|
int pio = adev->pio_mode - XFER_PIO_0;
|
|
int dma = adev->dma_mode - XFER_MW_DMA_0;
|
|
void __iomem *regio = ap->ioaddr.cmd_addr;
|
|
u8 addr;
|
|
|
|
/* Address table precomputed with a DCLK of 2 */
|
|
static const u8 addr_timing[2][5] = {
|
|
{ 0x30, 0x20, 0x20, 0x10, 0x10 },
|
|
{ 0x20, 0x20, 0x10, 0x10, 0x10 }
|
|
};
|
|
static const u8 data_rec_timing[2][5] = {
|
|
{ 0x59, 0x46, 0x30, 0x20, 0x20 },
|
|
{ 0x46, 0x32, 0x20, 0x20, 0x10 }
|
|
};
|
|
static const u8 dma_data_rec_timing[2][3] = {
|
|
{ 0x76, 0x20, 0x20 },
|
|
{ 0x54, 0x20, 0x10 }
|
|
};
|
|
|
|
/* Switch from IDE to control mode */
|
|
optidma_unlock(ap);
|
|
|
|
|
|
/*
|
|
* As with many controllers the address setup time is shared
|
|
* and must suit both devices if present. FIXME: Check if we
|
|
* need to look at slowest of PIO/DMA mode of either device
|
|
*/
|
|
|
|
if (mode >= XFER_MW_DMA_0)
|
|
addr = 0;
|
|
else
|
|
addr = addr_timing[pci_clock][pio];
|
|
|
|
if (pair) {
|
|
u8 pair_addr;
|
|
/* Hardware constraint */
|
|
if (pair->dma_mode)
|
|
pair_addr = 0;
|
|
else
|
|
pair_addr = addr_timing[pci_clock][pair->pio_mode - XFER_PIO_0];
|
|
if (pair_addr > addr)
|
|
addr = pair_addr;
|
|
}
|
|
|
|
/* Commence primary programming sequence */
|
|
/* First we load the device number into the timing select */
|
|
iowrite8(adev->devno, regio + MISC_REG);
|
|
/* Now we load the data timings into read data/write data */
|
|
if (mode < XFER_MW_DMA_0) {
|
|
iowrite8(data_rec_timing[pci_clock][pio], regio + READ_REG);
|
|
iowrite8(data_rec_timing[pci_clock][pio], regio + WRITE_REG);
|
|
} else if (mode < XFER_UDMA_0) {
|
|
iowrite8(dma_data_rec_timing[pci_clock][dma], regio + READ_REG);
|
|
iowrite8(dma_data_rec_timing[pci_clock][dma], regio + WRITE_REG);
|
|
}
|
|
/* Finally we load the address setup into the misc register */
|
|
iowrite8(addr | adev->devno, regio + MISC_REG);
|
|
|
|
/* Programming sequence complete, timing 0 dev 0, timing 1 dev 1 */
|
|
iowrite8(0x85, regio + CNTRL_REG);
|
|
|
|
/* Switch back to IDE mode */
|
|
optidma_lock(ap);
|
|
|
|
/* Note: at this point our programming is incomplete. We are
|
|
not supposed to program PCI 0x43 "things we hacked onto the chip"
|
|
until we've done both sets of PIO/DMA timings */
|
|
}
|
|
|
|
/**
|
|
* optiplus_mode_setup - DMA setup for Firestar Plus
|
|
* @ap: ATA port
|
|
* @adev: device
|
|
* @mode: desired mode
|
|
*
|
|
* The Firestar plus has additional UDMA functionality for UDMA0-2 and
|
|
* requires we do some additional work. Because the base work we must do
|
|
* is mostly shared we wrap the Firestar setup functionality in this
|
|
* one
|
|
*/
|
|
|
|
static void optiplus_mode_setup(struct ata_port *ap, struct ata_device *adev, u8 mode)
|
|
{
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
u8 udcfg;
|
|
u8 udslave;
|
|
int dev2 = 2 * adev->devno;
|
|
int unit = 2 * ap->port_no + adev->devno;
|
|
int udma = mode - XFER_UDMA_0;
|
|
|
|
pci_read_config_byte(pdev, 0x44, &udcfg);
|
|
if (mode <= XFER_UDMA_0) {
|
|
udcfg &= ~(1 << unit);
|
|
optidma_mode_setup(ap, adev, adev->dma_mode);
|
|
} else {
|
|
udcfg |= (1 << unit);
|
|
if (ap->port_no) {
|
|
pci_read_config_byte(pdev, 0x45, &udslave);
|
|
udslave &= ~(0x03 << dev2);
|
|
udslave |= (udma << dev2);
|
|
pci_write_config_byte(pdev, 0x45, udslave);
|
|
} else {
|
|
udcfg &= ~(0x30 << dev2);
|
|
udcfg |= (udma << dev2);
|
|
}
|
|
}
|
|
pci_write_config_byte(pdev, 0x44, udcfg);
|
|
}
|
|
|
|
/**
|
|
* optidma_set_pio_mode - PIO setup callback
|
|
* @ap: ATA port
|
|
* @adev: Device
|
|
*
|
|
* The libata core provides separate functions for handling PIO and
|
|
* DMA programming. The architecture of the Firestar makes it easier
|
|
* for us to have a common function so we provide wrappers
|
|
*/
|
|
|
|
static void optidma_set_pio_mode(struct ata_port *ap, struct ata_device *adev)
|
|
{
|
|
optidma_mode_setup(ap, adev, adev->pio_mode);
|
|
}
|
|
|
|
/**
|
|
* optidma_set_dma_mode - DMA setup callback
|
|
* @ap: ATA port
|
|
* @adev: Device
|
|
*
|
|
* The libata core provides separate functions for handling PIO and
|
|
* DMA programming. The architecture of the Firestar makes it easier
|
|
* for us to have a common function so we provide wrappers
|
|
*/
|
|
|
|
static void optidma_set_dma_mode(struct ata_port *ap, struct ata_device *adev)
|
|
{
|
|
optidma_mode_setup(ap, adev, adev->dma_mode);
|
|
}
|
|
|
|
/**
|
|
* optiplus_set_pio_mode - PIO setup callback
|
|
* @ap: ATA port
|
|
* @adev: Device
|
|
*
|
|
* The libata core provides separate functions for handling PIO and
|
|
* DMA programming. The architecture of the Firestar makes it easier
|
|
* for us to have a common function so we provide wrappers
|
|
*/
|
|
|
|
static void optiplus_set_pio_mode(struct ata_port *ap, struct ata_device *adev)
|
|
{
|
|
optiplus_mode_setup(ap, adev, adev->pio_mode);
|
|
}
|
|
|
|
/**
|
|
* optiplus_set_dma_mode - DMA setup callback
|
|
* @ap: ATA port
|
|
* @adev: Device
|
|
*
|
|
* The libata core provides separate functions for handling PIO and
|
|
* DMA programming. The architecture of the Firestar makes it easier
|
|
* for us to have a common function so we provide wrappers
|
|
*/
|
|
|
|
static void optiplus_set_dma_mode(struct ata_port *ap, struct ata_device *adev)
|
|
{
|
|
optiplus_mode_setup(ap, adev, adev->dma_mode);
|
|
}
|
|
|
|
/**
|
|
* optidma_make_bits - PCI setup helper
|
|
* @adev: ATA device
|
|
*
|
|
* Turn the ATA device setup into PCI configuration bits
|
|
* for register 0x43 and return the two bits needed.
|
|
*/
|
|
|
|
static u8 optidma_make_bits43(struct ata_device *adev)
|
|
{
|
|
static const u8 bits43[5] = {
|
|
0, 0, 0, 1, 2
|
|
};
|
|
if (!ata_dev_enabled(adev))
|
|
return 0;
|
|
if (adev->dma_mode)
|
|
return adev->dma_mode - XFER_MW_DMA_0;
|
|
return bits43[adev->pio_mode - XFER_PIO_0];
|
|
}
|
|
|
|
/**
|
|
* optidma_set_mode - mode setup
|
|
* @link: link to set up
|
|
*
|
|
* Use the standard setup to tune the chipset and then finalise the
|
|
* configuration by writing the nibble of extra bits of data into
|
|
* the chip.
|
|
*/
|
|
|
|
static int optidma_set_mode(struct ata_link *link, struct ata_device **r_failed)
|
|
{
|
|
struct ata_port *ap = link->ap;
|
|
u8 r;
|
|
int nybble = 4 * ap->port_no;
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
int rc = ata_do_set_mode(link, r_failed);
|
|
if (rc == 0) {
|
|
pci_read_config_byte(pdev, 0x43, &r);
|
|
|
|
r &= (0x0F << nybble);
|
|
r |= (optidma_make_bits43(&link->device[0]) +
|
|
(optidma_make_bits43(&link->device[0]) << 2)) << nybble;
|
|
pci_write_config_byte(pdev, 0x43, r);
|
|
}
|
|
return rc;
|
|
}
|
|
|
|
static struct scsi_host_template optidma_sht = {
|
|
ATA_BMDMA_SHT(DRV_NAME),
|
|
};
|
|
|
|
static struct ata_port_operations optidma_port_ops = {
|
|
.inherits = &ata_bmdma_port_ops,
|
|
.cable_detect = ata_cable_40wire,
|
|
.set_piomode = optidma_set_pio_mode,
|
|
.set_dmamode = optidma_set_dma_mode,
|
|
.set_mode = optidma_set_mode,
|
|
.prereset = optidma_pre_reset,
|
|
};
|
|
|
|
static struct ata_port_operations optiplus_port_ops = {
|
|
.inherits = &optidma_port_ops,
|
|
.set_piomode = optiplus_set_pio_mode,
|
|
.set_dmamode = optiplus_set_dma_mode,
|
|
};
|
|
|
|
/**
|
|
* optiplus_with_udma - Look for UDMA capable setup
|
|
* @pdev; ATA controller
|
|
*/
|
|
|
|
static int optiplus_with_udma(struct pci_dev *pdev)
|
|
{
|
|
u8 r;
|
|
int ret = 0;
|
|
int ioport = 0x22;
|
|
struct pci_dev *dev1;
|
|
|
|
/* Find function 1 */
|
|
dev1 = pci_get_device(0x1045, 0xC701, NULL);
|
|
if (dev1 == NULL)
|
|
return 0;
|
|
|
|
/* Rev must be >= 0x10 */
|
|
pci_read_config_byte(dev1, 0x08, &r);
|
|
if (r < 0x10)
|
|
goto done_nomsg;
|
|
/* Read the chipset system configuration to check our mode */
|
|
pci_read_config_byte(dev1, 0x5F, &r);
|
|
ioport |= (r << 8);
|
|
outb(0x10, ioport);
|
|
/* Must be 66Mhz sync */
|
|
if ((inb(ioport + 2) & 1) == 0)
|
|
goto done;
|
|
|
|
/* Check the ATA arbitration/timing is suitable */
|
|
pci_read_config_byte(pdev, 0x42, &r);
|
|
if ((r & 0x36) != 0x36)
|
|
goto done;
|
|
pci_read_config_byte(dev1, 0x52, &r);
|
|
if (r & 0x80) /* IDEDIR disabled */
|
|
ret = 1;
|
|
done:
|
|
printk(KERN_WARNING "UDMA not supported in this configuration.\n");
|
|
done_nomsg: /* Wrong chip revision */
|
|
pci_dev_put(dev1);
|
|
return ret;
|
|
}
|
|
|
|
static int optidma_init_one(struct pci_dev *dev, const struct pci_device_id *id)
|
|
{
|
|
static const struct ata_port_info info_82c700 = {
|
|
.flags = ATA_FLAG_SLAVE_POSS,
|
|
.pio_mask = ATA_PIO4,
|
|
.mwdma_mask = ATA_MWDMA2,
|
|
.port_ops = &optidma_port_ops
|
|
};
|
|
static const struct ata_port_info info_82c700_udma = {
|
|
.flags = ATA_FLAG_SLAVE_POSS,
|
|
.pio_mask = ATA_PIO4,
|
|
.mwdma_mask = ATA_MWDMA2,
|
|
.udma_mask = ATA_UDMA2,
|
|
.port_ops = &optiplus_port_ops
|
|
};
|
|
const struct ata_port_info *ppi[] = { &info_82c700, NULL };
|
|
int rc;
|
|
|
|
ata_print_version_once(&dev->dev, DRV_VERSION);
|
|
|
|
rc = pcim_enable_device(dev);
|
|
if (rc)
|
|
return rc;
|
|
|
|
/* Fixed location chipset magic */
|
|
inw(0x1F1);
|
|
inw(0x1F1);
|
|
pci_clock = inb(0x1F5) & 1; /* 0 = 33Mhz, 1 = 25Mhz */
|
|
|
|
if (optiplus_with_udma(dev))
|
|
ppi[0] = &info_82c700_udma;
|
|
|
|
return ata_pci_bmdma_init_one(dev, ppi, &optidma_sht, NULL, 0);
|
|
}
|
|
|
|
static const struct pci_device_id optidma[] = {
|
|
{ PCI_VDEVICE(OPTI, 0xD568), }, /* Opti 82C700 */
|
|
|
|
{ },
|
|
};
|
|
|
|
static struct pci_driver optidma_pci_driver = {
|
|
.name = DRV_NAME,
|
|
.id_table = optidma,
|
|
.probe = optidma_init_one,
|
|
.remove = ata_pci_remove_one,
|
|
#ifdef CONFIG_PM_SLEEP
|
|
.suspend = ata_pci_device_suspend,
|
|
.resume = ata_pci_device_resume,
|
|
#endif
|
|
};
|
|
|
|
module_pci_driver(optidma_pci_driver);
|
|
|
|
MODULE_AUTHOR("Alan Cox");
|
|
MODULE_DESCRIPTION("low-level driver for Opti Firestar/Firestar Plus");
|
|
MODULE_LICENSE("GPL");
|
|
MODULE_DEVICE_TABLE(pci, optidma);
|
|
MODULE_VERSION(DRV_VERSION);
|