mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-28 11:18:45 +07:00
cff7597a46
Need to specify the inductor size in nH. This is a required property. Signed-off-by: Brian Austin <brian.austin@cirrus.com> Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org>
184 lines
6.2 KiB
Plaintext
184 lines
6.2 KiB
Plaintext
CS35L35 Boosted Speaker Amplifier
|
|
|
|
Required properties:
|
|
|
|
- compatible : "cirrus,cs35l35"
|
|
|
|
- reg : the I2C address of the device for I2C
|
|
|
|
- VA-supply, VP-supply : power supplies for the device,
|
|
as covered in
|
|
Documentation/devicetree/bindings/regulator/regulator.txt.
|
|
|
|
- interrupt-parent : Specifies the phandle of the interrupt controller to
|
|
which the IRQs from CS35L35 are delivered to.
|
|
- interrupts : IRQ line info CS35L35.
|
|
(See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
|
|
for further information relating to interrupt properties)
|
|
|
|
- cirrus,boost-ind-nanohenry: Inductor value for boost converter. The value is
|
|
in nH and they can be values of 1000nH, 1200nH, 1500nH, and 2200nH.
|
|
|
|
Optional properties:
|
|
- reset-gpios : gpio used to reset the amplifier
|
|
|
|
- cirrus,stereo-config : Boolean to determine if there are 2 AMPs for a
|
|
Stereo configuration
|
|
|
|
- cirrus,audio-channel : Set Location of Audio Signal on Serial Port
|
|
0 = Data Packet received on Left I2S Channel
|
|
1 = Data Packet received on Right I2S Channel
|
|
|
|
- cirrus,advisory-channel : Set Location of Advisory Signal on Serial Port
|
|
0 = Data Packet received on Left I2S Channel
|
|
1 = Data Packet received on Right I2S Channel
|
|
|
|
- cirrus,shared-boost : Boolean to enable ClassH tracking of Advisory Signal
|
|
if 2 Devices share Boost BST_CTL
|
|
|
|
- cirrus,external-boost : Boolean to specify the device is using an external
|
|
boost supply, note that sharing a boost from another cs35l35 would constitute
|
|
using an external supply for the slave device
|
|
|
|
- cirrus,sp-drv-strength : Value for setting the Serial Port drive strength
|
|
Table 3-10 of the datasheet lists drive-strength specifications
|
|
0 = 1x (Default)
|
|
1 = .5x
|
|
- cirrus,sp-drv-unused : Determines how unused slots should be driven on the
|
|
Serial Port.
|
|
0 - Hi-Z
|
|
2 - Drive 0's (Default)
|
|
3 - Drive 1's
|
|
|
|
- cirrus,bst-pdn-fet-on : Boolean to determine if the Boost PDN control
|
|
powers down with a rectification FET On or Off. If VSPK is supplied
|
|
externally then FET is off.
|
|
|
|
- cirrus,boost-ctl-millivolt : Boost Voltage Value. Configures the boost
|
|
converter's output voltage in mV. The range is from 2600mV to 9000mV with
|
|
increments of 100mV.
|
|
(Default) VP
|
|
|
|
- cirrus,boost-peak-milliamp : Boost-converter peak current limit in mA.
|
|
Configures the peak current by monitoring the current through the boost FET.
|
|
Range starts at 1680mA and goes to a maximum of 4480mA with increments of
|
|
110mA.
|
|
(Default) 2.46 Amps
|
|
|
|
- cirrus,amp-gain-zc : Boolean to determine if to use Amplifier gain-change
|
|
zero-cross
|
|
|
|
Optional H/G Algorithm sub-node:
|
|
|
|
The cs35l35 node can have a single "cirrus,classh-internal-algo" sub-node
|
|
that will disable automatic control of the internal H/G Algorithm.
|
|
|
|
It is strongly recommended that the Datasheet be referenced when adjusting
|
|
or using these Class H Algorithm controls over the internal Algorithm.
|
|
Serious damage can occur to the Device and surrounding components.
|
|
|
|
- cirrus,classh-internal-algo : Sub-node for the Internal Class H Algorithm
|
|
See Section 4.3 Internal Class H Algorithm in the Datasheet.
|
|
If not used, the device manages the ClassH Algorithm internally.
|
|
|
|
Optional properties for the "cirrus,classh-internal-algo" Sub-node
|
|
|
|
Section 7.29 Class H Control
|
|
- cirrus,classh-bst-overide : Boolean
|
|
- cirrus,classh-bst-max-limit
|
|
- cirrus,classh-mem-depth
|
|
|
|
Section 7.30 Class H Headroom Control
|
|
- cirrus,classh-headroom
|
|
|
|
Section 7.31 Class H Release Rate
|
|
- cirrus,classh-release-rate
|
|
|
|
Section 7.32 Class H Weak FET Drive Control
|
|
- cirrus,classh-wk-fet-disable
|
|
- cirrus,classh-wk-fet-delay
|
|
- cirrus,classh-wk-fet-thld
|
|
|
|
Section 7.34 Class H VP Control
|
|
- cirrus,classh-vpch-auto
|
|
- cirrus,classh-vpch-rate
|
|
- cirrus,classh-vpch-man
|
|
|
|
Optional Monitor Signal Format sub-node:
|
|
|
|
The cs35l35 node can have a single "cirrus,monitor-signal-format" sub-node
|
|
for adjusting the Depth, Location and Frame of the Monitoring Signals
|
|
for Algorithms.
|
|
|
|
See Sections 4.8.2 through 4.8.4 Serial-Port Control in the Datasheet
|
|
|
|
-cirrus,monitor-signal-format : Sub-node for the Monitor Signaling Formating
|
|
on the I2S Port. Each of the 3 8 bit values in the array contain the settings
|
|
for depth, location, and frame.
|
|
|
|
If not used, the defaults for the 6 monitor signals is used.
|
|
|
|
Sections 7.44 - 7.53 lists values for the depth, location, and frame
|
|
for each monitoring signal.
|
|
|
|
- cirrus,imon : 4 8 bit values to set the depth, location, frame and ADC
|
|
scale of the IMON monitor signal.
|
|
|
|
- cirrus,vmon : 3 8 bit values to set the depth, location, and frame
|
|
of the VMON monitor signal.
|
|
|
|
- cirrus,vpmon : 3 8 bit values to set the depth, location, and frame
|
|
of the VPMON monitor signal.
|
|
|
|
- cirrus,vbstmon : 3 8 bit values to set the depth, location, and frame
|
|
of the VBSTMON monitor signal
|
|
|
|
- cirrus,vpbrstat : 3 8 bit values to set the depth, location, and frame
|
|
of the VPBRSTAT monitor signal
|
|
|
|
- cirrus,zerofill : 3 8 bit values to set the depth, location, and frame\
|
|
of the ZEROFILL packet in the monitor signal
|
|
|
|
Example:
|
|
|
|
cs35l35: cs35l35@20 {
|
|
compatible = "cirrus,cs35l35";
|
|
reg = <0x20>;
|
|
VA-supply = <&dummy_vreg>;
|
|
VP-supply = <&dummy_vreg>;
|
|
reset-gpios = <&axi_gpio 54 0>;
|
|
interrupt-parent = <&gpio8>;
|
|
interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
|
|
cirrus,boost-ctl-millivolt = <9000>;
|
|
|
|
cirrus,stereo-config;
|
|
cirrus,audio-channel = <0x00>;
|
|
cirrus,advisory-channel = <0x01>;
|
|
cirrus,shared-boost;
|
|
|
|
cirrus,classh-internal-algo {
|
|
cirrus,classh-bst-overide;
|
|
cirrus,classh-bst-max-limit = <0x01>;
|
|
cirrus,classh-mem-depth = <0x01>;
|
|
cirrus,classh-release-rate = <0x08>;
|
|
cirrus,classh-headroom-millivolt = <0x0B>;
|
|
cirrus,classh-wk-fet-disable = <0x01>;
|
|
cirrus,classh-wk-fet-delay = <0x04>;
|
|
cirrus,classh-wk-fet-thld = <0x01>;
|
|
cirrus,classh-vpch-auto = <0x01>;
|
|
cirrus,classh-vpch-rate = <0x02>;
|
|
cirrus,classh-vpch-man = <0x05>;
|
|
};
|
|
|
|
/* Depth, Location, Frame */
|
|
cirrus,monitor-signal-format {
|
|
cirrus,imon = /bits/ 8 <0x03 0x00 0x01>;
|
|
cirrus,vmon = /bits/ 8 <0x03 0x00 0x00>;
|
|
cirrus,vpmon = /bits/ 8 <0x03 0x04 0x00>;
|
|
cirrus,vbstmon = /bits/ 8 <0x03 0x04 0x01>;
|
|
cirrus,vpbrstat = /bits/ 8 <0x00 0x04 0x00>;
|
|
cirrus,zerofill = /bits/ 8 <0x00 0x00 0x00>;
|
|
};
|
|
|
|
};
|