linux_dsm_epyc7002/Documentation/mmc/mmc-dev-attrs.txt
Loic Pallardy 188cc0424e mmc: core: Extend sysfs to ext_csd parameters for RPMB support
Extend current sysfs access to ext_csd rpmb parameters (RPMB partition
size) and rel_sector information.

Signed-off-by: Loic Pallardy <loic.pallardy@stericsson.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Johan Rudholm <johan.rudholm@stericsson.com>
Acked-by: Krishna Konda <kkonda@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-12-06 13:54:48 -05:00

84 lines
3.1 KiB
Plaintext

SD and MMC Block Device Attributes
==================================
These attributes are defined for the block devices associated with the
SD or MMC device.
The following attributes are read/write.
force_ro Enforce read-only access even if write protect switch is off.
SD and MMC Device Attributes
============================
All attributes are read-only.
cid Card Identifaction Register
csd Card Specific Data Register
scr SD Card Configuration Register (SD only)
date Manufacturing Date (from CID Register)
fwrev Firmware/Product Revision (from CID Register) (SD and MMCv1 only)
hwrev Hardware/Product Revision (from CID Register) (SD and MMCv1 only)
manfid Manufacturer ID (from CID Register)
name Product Name (from CID Register)
oemid OEM/Application ID (from CID Register)
serial Product Serial Number (from CID Register)
erase_size Erase group size
preferred_erase_size Preferred erase size
raw_rpmb_size_mult RPMB partition size
rel_sectors Reliable write sector count
Note on Erase Size and Preferred Erase Size:
"erase_size" is the minimum size, in bytes, of an erase
operation. For MMC, "erase_size" is the erase group size
reported by the card. Note that "erase_size" does not apply
to trim or secure trim operations where the minimum size is
always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on
the card wait. This is not a problem if the whole card
is being erased, but erasing one partition will make
I/O for another partition on the same card wait for the
duration of the erase - which could be a several
minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very
useful. Because the erase timeout contains a margin
which is multiplied by the size of the erase area,
the value can end up being several minutes for large
areas.
"erase_size" is not the most efficient unit to erase
(especially for SD where it is just one sector),
hence "preferred_erase_size" provides a good chunk
size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity
erase size if a card specifies one, otherwise it is
based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit
size specified by the card.
"preferred_erase_size" is in bytes.
Note on raw_rpmb_size_mult:
"raw_rpmb_size_mult" is a mutliple of 128kB block.
RPMB size in byte is calculated by using the following equation:
RPMB partition size = 128kB x raw_rpmb_size_mult
SD/MMC/SDIO Clock Gating Attribute
==================================
Read and write access is provided to following attribute.
This attribute appears only if CONFIG_MMC_CLKGATE is enabled.
clkgate_delay Tune the clock gating delay with desired value in milliseconds.
echo <desired delay> > /sys/class/mmc_host/mmcX/clkgate_delay