mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-28 11:18:45 +07:00
ed1a230f96
Driver support for the Summit I²C battery charger. This is used in some Intel devices. Signed-off-by: Bruce E. Robertson <bruce.e.robertson@intel.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
118 lines
4.5 KiB
C
118 lines
4.5 KiB
C
/*
|
|
* Summit Microelectronics SMB347 Battery Charger Driver
|
|
*
|
|
* Copyright (C) 2011, Intel Corporation
|
|
*
|
|
* Authors: Bruce E. Robertson <bruce.e.robertson@intel.com>
|
|
* Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 as
|
|
* published by the Free Software Foundation.
|
|
*/
|
|
|
|
#ifndef SMB347_CHARGER_H
|
|
#define SMB347_CHARGER_H
|
|
|
|
#include <linux/types.h>
|
|
#include <linux/power_supply.h>
|
|
|
|
enum {
|
|
/* use the default compensation method */
|
|
SMB347_SOFT_TEMP_COMPENSATE_DEFAULT = -1,
|
|
|
|
SMB347_SOFT_TEMP_COMPENSATE_NONE,
|
|
SMB347_SOFT_TEMP_COMPENSATE_CURRENT,
|
|
SMB347_SOFT_TEMP_COMPENSATE_VOLTAGE,
|
|
};
|
|
|
|
/* Use default factory programmed value for hard/soft temperature limit */
|
|
#define SMB347_TEMP_USE_DEFAULT -273
|
|
|
|
/*
|
|
* Charging enable can be controlled by software (via i2c) by
|
|
* smb347-charger driver or by EN pin (active low/high).
|
|
*/
|
|
enum smb347_chg_enable {
|
|
SMB347_CHG_ENABLE_SW,
|
|
SMB347_CHG_ENABLE_PIN_ACTIVE_LOW,
|
|
SMB347_CHG_ENABLE_PIN_ACTIVE_HIGH,
|
|
};
|
|
|
|
/**
|
|
* struct smb347_charger_platform_data - platform data for SMB347 charger
|
|
* @battery_info: Information about the battery
|
|
* @max_charge_current: maximum current (in uA) the battery can be charged
|
|
* @max_charge_voltage: maximum voltage (in uV) the battery can be charged
|
|
* @pre_charge_current: current (in uA) to use in pre-charging phase
|
|
* @termination_current: current (in uA) used to determine when the
|
|
* charging cycle terminates
|
|
* @pre_to_fast_voltage: voltage (in uV) treshold used for transitioning to
|
|
* pre-charge to fast charge mode
|
|
* @mains_current_limit: maximum input current drawn from AC/DC input (in uA)
|
|
* @usb_hc_current_limit: maximum input high current (in uA) drawn from USB
|
|
* input
|
|
* @chip_temp_threshold: die temperature where device starts limiting charge
|
|
* current [%100 - %130] (in degree C)
|
|
* @soft_cold_temp_limit: soft cold temperature limit [%0 - %15] (in degree C),
|
|
* granularity is 5 deg C.
|
|
* @soft_hot_temp_limit: soft hot temperature limit [%40 - %55] (in degree C),
|
|
* granularity is 5 deg C.
|
|
* @hard_cold_temp_limit: hard cold temperature limit [%-5 - %10] (in degree C),
|
|
* granularity is 5 deg C.
|
|
* @hard_hot_temp_limit: hard hot temperature limit [%50 - %65] (in degree C),
|
|
* granularity is 5 deg C.
|
|
* @suspend_on_hard_temp_limit: suspend charging when hard limit is hit
|
|
* @soft_temp_limit_compensation: compensation method when soft temperature
|
|
* limit is hit
|
|
* @charge_current_compensation: current (in uA) for charging compensation
|
|
* current when temperature hits soft limits
|
|
* @use_mains: AC/DC input can be used
|
|
* @use_usb: USB input can be used
|
|
* @use_usb_otg: USB OTG output can be used (not implemented yet)
|
|
* @irq_gpio: GPIO number used for interrupts (%-1 if not used)
|
|
* @enable_control: how charging enable/disable is controlled
|
|
* (driver/pin controls)
|
|
*
|
|
* @use_main, @use_usb, and @use_usb_otg are means to enable/disable
|
|
* hardware support for these. This is useful when we want to have for
|
|
* example OTG charging controlled via OTG transceiver driver and not by
|
|
* the SMB347 hardware.
|
|
*
|
|
* Hard and soft temperature limit values are given as described in the
|
|
* device data sheet and assuming NTC beta value is %3750. Even if this is
|
|
* not the case, these values should be used. They can be mapped to the
|
|
* corresponding NTC beta values with the help of table %2 in the data
|
|
* sheet. So for example if NTC beta is %3375 and we want to program hard
|
|
* hot limit to be %53 deg C, @hard_hot_temp_limit should be set to %50.
|
|
*
|
|
* If zero value is given in any of the current and voltage values, the
|
|
* factory programmed default will be used. For soft/hard temperature
|
|
* values, pass in %SMB347_TEMP_USE_DEFAULT instead.
|
|
*/
|
|
struct smb347_charger_platform_data {
|
|
struct power_supply_info battery_info;
|
|
unsigned int max_charge_current;
|
|
unsigned int max_charge_voltage;
|
|
unsigned int pre_charge_current;
|
|
unsigned int termination_current;
|
|
unsigned int pre_to_fast_voltage;
|
|
unsigned int mains_current_limit;
|
|
unsigned int usb_hc_current_limit;
|
|
unsigned int chip_temp_threshold;
|
|
int soft_cold_temp_limit;
|
|
int soft_hot_temp_limit;
|
|
int hard_cold_temp_limit;
|
|
int hard_hot_temp_limit;
|
|
bool suspend_on_hard_temp_limit;
|
|
unsigned int soft_temp_limit_compensation;
|
|
unsigned int charge_current_compensation;
|
|
bool use_mains;
|
|
bool use_usb;
|
|
bool use_usb_otg;
|
|
int irq_gpio;
|
|
enum smb347_chg_enable enable_control;
|
|
};
|
|
|
|
#endif /* SMB347_CHARGER_H */
|