mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-23 13:00:33 +07:00
d97556c801
We need to also have OFFPULLUDENABLE bit set to use the off mode pull values. Otherwise the line is pulled down internally if no external pull exists. This is has some documentation at: http://processors.wiki.ti.com/index.php/Optimizing_OMAP35x_and_AM/DM37x_OFF_mode_PAD_configuration Note that the value is still glitchy during off mode transitions as documented in spz319f.pdf "Advisory 1.45". It's best to use external pulls instead of relying on the internal ones for off mode and even then anything pulled up will get driven down momentarily on off mode restore for GPIO banks other than bank1. Signed-off-by: Tony Lindgren <tony@atomide.com>
91 lines
3.0 KiB
C
91 lines
3.0 KiB
C
/*
|
|
* This header provides constants for OMAP pinctrl bindings.
|
|
*
|
|
* Copyright (C) 2009 Nokia
|
|
* Copyright (C) 2009-2010 Texas Instruments
|
|
*/
|
|
|
|
#ifndef _DT_BINDINGS_PINCTRL_OMAP_H
|
|
#define _DT_BINDINGS_PINCTRL_OMAP_H
|
|
|
|
/* 34xx mux mode options for each pin. See TRM for options */
|
|
#define MUX_MODE0 0
|
|
#define MUX_MODE1 1
|
|
#define MUX_MODE2 2
|
|
#define MUX_MODE3 3
|
|
#define MUX_MODE4 4
|
|
#define MUX_MODE5 5
|
|
#define MUX_MODE6 6
|
|
#define MUX_MODE7 7
|
|
|
|
/* 24xx/34xx mux bit defines */
|
|
#define PULL_ENA (1 << 3)
|
|
#define PULL_UP (1 << 4)
|
|
#define ALTELECTRICALSEL (1 << 5)
|
|
|
|
/* omap3/4/5 specific mux bit defines */
|
|
#define INPUT_EN (1 << 8)
|
|
#define OFF_EN (1 << 9)
|
|
#define OFFOUT_EN (1 << 10)
|
|
#define OFFOUT_VAL (1 << 11)
|
|
#define OFF_PULL_EN (1 << 12)
|
|
#define OFF_PULL_UP (1 << 13)
|
|
#define WAKEUP_EN (1 << 14)
|
|
#define WAKEUP_EVENT (1 << 15)
|
|
|
|
/* Active pin states */
|
|
#define PIN_OUTPUT 0
|
|
#define PIN_OUTPUT_PULLUP (PIN_OUTPUT | PULL_ENA | PULL_UP)
|
|
#define PIN_OUTPUT_PULLDOWN (PIN_OUTPUT | PULL_ENA)
|
|
#define PIN_INPUT INPUT_EN
|
|
#define PIN_INPUT_PULLUP (PULL_ENA | INPUT_EN | PULL_UP)
|
|
#define PIN_INPUT_PULLDOWN (PULL_ENA | INPUT_EN)
|
|
|
|
/* Off mode states */
|
|
#define PIN_OFF_NONE 0
|
|
#define PIN_OFF_OUTPUT_HIGH (OFF_EN | OFFOUT_EN | OFFOUT_VAL)
|
|
#define PIN_OFF_OUTPUT_LOW (OFF_EN | OFFOUT_EN)
|
|
#define PIN_OFF_INPUT_PULLUP (OFF_EN | OFFOUT_EN | OFF_PULL_EN | OFF_PULL_UP)
|
|
#define PIN_OFF_INPUT_PULLDOWN (OFF_EN | OFFOUT_EN | OFF_PULL_EN)
|
|
#define PIN_OFF_WAKEUPENABLE WAKEUP_EN
|
|
|
|
/*
|
|
* Macros to allow using the absolute physical address instead of the
|
|
* padconf registers instead of the offset from padconf base.
|
|
*/
|
|
#define OMAP_IOPAD_OFFSET(pa, offset) (((pa) & 0xffff) - (offset))
|
|
|
|
#define OMAP2420_CORE_IOPAD(pa, val) OMAP_IOPAD_OFFSET((pa), 0x0030) (val)
|
|
#define OMAP2430_CORE_IOPAD(pa, val) OMAP_IOPAD_OFFSET((pa), 0x2030) (val)
|
|
#define OMAP3_CORE1_IOPAD(pa, val) OMAP_IOPAD_OFFSET((pa), 0x2030) (val)
|
|
#define OMAP3430_CORE2_IOPAD(pa, val) OMAP_IOPAD_OFFSET((pa), 0x25d8) (val)
|
|
#define OMAP3630_CORE2_IOPAD(pa, val) OMAP_IOPAD_OFFSET((pa), 0x25a0) (val)
|
|
#define OMAP3_WKUP_IOPAD(pa, val) OMAP_IOPAD_OFFSET((pa), 0x2a00) (val)
|
|
#define DM814X_IOPAD(pa, val) OMAP_IOPAD_OFFSET((pa), 0x0800) (val)
|
|
#define DM816X_IOPAD(pa, val) OMAP_IOPAD_OFFSET((pa), 0x0800) (val)
|
|
#define AM33XX_IOPAD(pa, val) OMAP_IOPAD_OFFSET((pa), 0x0800) (val)
|
|
|
|
/*
|
|
* Macros to allow using the offset from the padconf physical address
|
|
* instead of the offset from padconf base.
|
|
*/
|
|
#define OMAP_PADCONF_OFFSET(offset, base_offset) ((offset) - (base_offset))
|
|
|
|
#define OMAP4_IOPAD(offset, val) OMAP_PADCONF_OFFSET((offset), 0x0040) (val)
|
|
#define OMAP5_IOPAD(offset, val) OMAP_PADCONF_OFFSET((offset), 0x0040) (val)
|
|
|
|
/*
|
|
* Define some commonly used pins configured by the boards.
|
|
* Note that some boards use alternative pins, so check
|
|
* the schematics before using these.
|
|
*/
|
|
#define OMAP3_UART1_RX 0x152
|
|
#define OMAP3_UART2_RX 0x14a
|
|
#define OMAP3_UART3_RX 0x16e
|
|
#define OMAP4_UART2_RX 0xdc
|
|
#define OMAP4_UART3_RX 0x104
|
|
#define OMAP4_UART4_RX 0x11c
|
|
|
|
#endif
|
|
|