AuxXxilium/linux_dsm_epyc7002
1
0
Fork 0
mirror of https://github.com/AuxXxilium/linux_dsm_epyc7002.git synced 2024-12-23 00:47:11 +07:00
Code Issues Actions Packages Projects Releases Wiki Activity
c58a14a9cc
linux_dsm_epyc7002/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts
Stephen Boyd b993292f73 ARM: dts: qcom-apq8064: Collapse usb support into one node 
We currently have three device nodes for the same USB hardware
block, as evident by the reuse of the same reg address multiple
times. Now that the chipidea driver fully supports OTG with the
MSM wrapper we can collapse the three nodes into one USB device
node, reflecting the true nature of the hardware.

Since we're here, we also mark the irq trigger flags correctly,
as IRQ_TYPE_LEVEL_HIGH instead of IRQ_TYPE_NONE.

Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
2017-05-26 00:52:23 -05:00

381 lines
6.8 KiB
Plaintext
Raw Blame History

#include "qcom-apq8064-v2.0.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
/ {
model = "Qualcomm APQ8064/IFC6410";
compatible = "qcom,apq8064-ifc6410", "qcom,apq8064";
aliases {
serial0 = &gsbi7_serial;
serial1 = &gsbi6_serial;
i2c0 = &gsbi1_i2c;
i2c1 = &gsbi2_i2c;
i2c2 = &gsbi3_i2c;
i2c3 = &gsbi4_i2c;
spi0 = &gsbi5_spi;
};
chosen {
stdout-path = "serial0:115200n8";
};
pwrseq {
compatible = "simple-bus";
sdcc4_pwrseq: sdcc4_pwrseq {
pinctrl-names = "default";
pinctrl-0 = <&wlan_default_gpios>;
compatible = "mmc-pwrseq-simple";
reset-gpios = <&pm8921_gpio 43 GPIO_ACTIVE_LOW>;
};
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&notify_led>;
led@1 {
label = "apq8064:green:user1";
gpios = <&pm8921_gpio 18 GPIO_ACTIVE_HIGH>;
default-state = "on";
};
};
hdmi-out {
compatible = "hdmi-connector";
type = "d";
port {
hdmi_con: endpoint {
remote-endpoint = <&hdmi_out>;
};
};
};
soc {
pinctrl@800000 {
card_detect: card_detect {
mux {
pins = "gpio26";
function = "gpio";
bias-disable;
};
};
pcie_pins: pcie_pinmux {
mux {
pins = "gpio27";
function = "gpio";
};
conf {
pins = "gpio27";
drive-strength = <12>;
bias-disable;
};
};
};
rpm@108000 {
regulators {
vin_lvs1_3_6-supply = <&pm8921_s4>;
vin_lvs2-supply = <&pm8921_s1>;
vin_lvs4_5_7-supply = <&pm8921_s4>;
vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
vdd_l24-supply = <&pm8921_s1>;
vdd_l25-supply = <&pm8921_s1>;
vdd_l26-supply = <&pm8921_s7>;
vdd_l27-supply = <&pm8921_s7>;
vdd_l28-supply = <&pm8921_s7>;
/* Buck SMPS */
s1 {
regulator-always-on;
regulator-min-microvolt = <1225000>;
regulator-max-microvolt = <1225000>;
qcom,switch-mode-frequency = <3200000>;
bias-pull-down;
};
s3 {
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1400000>;
qcom,switch-mode-frequency = <4800000>;
};
s4 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
qcom,switch-mode-frequency = <3200000>;
};
s7 {
regulator-min-microvolt = <1300000>;
regulator-max-microvolt = <1300000>;
qcom,switch-mode-frequency = <3200000>;
};
l3 {
regulator-min-microvolt = <3050000>;
regulator-max-microvolt = <3300000>;
bias-pull-down;
};
l4 {
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1800000>;
bias-pull-down;
};
l5 {
regulator-min-microvolt = <2750000>;
regulator-max-microvolt = <3000000>;
bias-pull-down;
};
l6 {
regulator-min-microvolt = <2950000>;
regulator-max-microvolt = <2950000>;
bias-pull-down;
};
l23 {
regulator-min-microvolt = <1700000>;
regulator-max-microvolt = <1900000>;
bias-pull-down;
};
lvs1 {
bias-pull-down;
};
lvs6 {
bias-pull-down;
};
};
};
ext_3p3v: regulator-fixed@1 {
compatible = "regulator-fixed";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "ext_3p3v";
regulator-type = "voltage";
startup-delay-us = <0>;
gpio = <&tlmm_pinmux 77 GPIO_ACTIVE_HIGH>;
enable-active-high;
regulator-boot-on;
};
gsbi3: gsbi@16200000 {
status = "okay";
qcom,mode = <GSBI_PROT_I2C>;
i2c@16280000 {
status = "okay";
};
};
gsbi@16300000 {
status = "okay";
qcom,mode = <GSBI_PROT_I2C>;
/* CAM I2C MIPI-CSI connector */
i2c@16380000 {
status = "okay";
};
};
gsbi@12440000 {
status = "okay";
qcom,mode = <GSBI_PROT_I2C>;
i2c@12460000 {
status = "okay";
clock-frequency = <200000>;
eeprom@52 {
compatible = "atmel,24c128";
reg = <0x52>;
pagesize = <32>;
};
};
};
gsbi@1a200000 {
qcom,mode = <GSBI_PROT_SPI>;
status = "okay";
spi4: spi@1a280000 {
status = "okay";
num-cs = <1>;
cs-gpios = <&tlmm_pinmux 53 0>;
};
};
gsbi@16500000 {
status = "ok";
qcom,mode = <GSBI_PROT_UART_W_FC>;
serial@16540000 {
status = "ok";
pinctrl-names = "default";
pinctrl-0 = <&gsbi6_uart_4pins>;
};
};
gsbi@16600000 {
status = "ok";
qcom,mode = <GSBI_PROT_I2C_UART>;
serial@16640000 {
status = "ok";
pinctrl-names = "default";
pinctrl-0 = <&gsbi7_uart_2pins>;
};
};
sata_phy0: phy@1b400000 {
status = "okay";
};
sata0: sata@29000000 {
status = "okay";
target-supply = <&pm8921_s4>;
};
/* OTG */
usb@12500000 {
status = "okay";
dr_mode = "otg";
ulpi {
phy {
v3p3-supply = <&pm8921_l3>;
v1p8-supply = <&pm8921_l4>;
};
};
};
usb@12520000 {
status = "okay";
dr_mode = "host";
ulpi {
phy {
v3p3-supply = <&pm8921_l3>;
v1p8-supply = <&pm8921_l23>;
};
};
};
usb@12530000 {
status = "okay";
dr_mode = "host";
ulpi {
phy {
v3p3-supply = <&pm8921_l3>;
v1p8-supply = <&pm8921_l23>;
};
};
};
pci@1b500000 {
status = "ok";
vdda-supply = <&pm8921_s3>;
vdda_phy-supply = <&pm8921_lvs6>;
vdda_refclk-supply = <&ext_3p3v>;
pinctrl-0 = <&pcie_pins>;
pinctrl-names = "default";
perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
};
qcom,ssbi@500000 {
pmic@0 {
gpio@150 {
wlan_default_gpios: wlan-gpios {
pios {
pins = "gpio43";
function = "normal";
bias-disable;
power-source = <PM8921_GPIO_S4>;
};
};
notify_led: nled {
pios {
pins = "gpio18";
function = "normal";
bias-disable;
power-source = <PM8921_GPIO_S4>;
};
};
};
};
};
amba {
/* eMMC */
sdcc1: sdcc@12400000 {
status = "okay";
vmmc-supply = <&pm8921_l5>;
vqmmc-supply = <&pm8921_s4>;
};
/* External micro SD card */
sdcc3: sdcc@12180000 {
status = "okay";
vmmc-supply = <&pm8921_l6>;
pinctrl-names = "default";
pinctrl-0 = <&card_detect>;
cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
};
/* WLAN */
sdcc4: sdcc@121c0000 {
status = "okay";
vmmc-supply = <&ext_3p3v>;
vqmmc-supply = <&pm8921_lvs1>;
mmc-pwrseq = <&sdcc4_pwrseq>;
};
};
hdmi-tx@4a00000 {
status = "okay";
core-vdda-supply = <&pm8921_hdmi_switch>;
hdmi-mux-supply = <&ext_3p3v>;
hpd-gpios = <&tlmm_pinmux 72 GPIO_ACTIVE_HIGH>;
ports {
port@0 {
endpoint {
remote-endpoint = <&mdp_dtv_out>;
};
};
port@1 {
endpoint {
remote-endpoint = <&hdmi_con>;
};
};
};
};
hdmi-phy@4a00400 {
status = "okay";
core-vdda-supply = <&pm8921_hdmi_switch>;
};
mdp@5100000 {
status = "okay";
ports {
port@3 {
endpoint {
remote-endpoint = <&hdmi_in>;
};
};
};
};
};
};
Reference in New Issue View Git Blame Copy Permalink