linux_dsm_epyc7002/drivers/i2c/busses/i2c-qup.c
Sricharan R c4f0c5fb38 i2c: qup: Change qup_wait_writeready function to use for all timeouts
qup_wait_writeready waits only on a output fifo empty event.
Change the same function to accept the event and data length
to wait as parameters. This way the same function can be used for
timeouts in other places as well.

Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Tested-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Telkar Nagender <ntelkar@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-02-12 19:29:39 +01:00

804 lines
18 KiB
C

/*
* Copyright (c) 2009-2013, The Linux Foundation. All rights reserved.
* Copyright (c) 2014, Sony Mobile Communications AB.
*
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 and
* only version 2 as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
*/
#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/i2c.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/platform_device.h>
#include <linux/pm_runtime.h>
/* QUP Registers */
#define QUP_CONFIG 0x000
#define QUP_STATE 0x004
#define QUP_IO_MODE 0x008
#define QUP_SW_RESET 0x00c
#define QUP_OPERATIONAL 0x018
#define QUP_ERROR_FLAGS 0x01c
#define QUP_ERROR_FLAGS_EN 0x020
#define QUP_HW_VERSION 0x030
#define QUP_MX_OUTPUT_CNT 0x100
#define QUP_OUT_FIFO_BASE 0x110
#define QUP_MX_WRITE_CNT 0x150
#define QUP_MX_INPUT_CNT 0x200
#define QUP_MX_READ_CNT 0x208
#define QUP_IN_FIFO_BASE 0x218
#define QUP_I2C_CLK_CTL 0x400
#define QUP_I2C_STATUS 0x404
/* QUP States and reset values */
#define QUP_RESET_STATE 0
#define QUP_RUN_STATE 1
#define QUP_PAUSE_STATE 3
#define QUP_STATE_MASK 3
#define QUP_STATE_VALID BIT(2)
#define QUP_I2C_MAST_GEN BIT(4)
#define QUP_OPERATIONAL_RESET 0x000ff0
#define QUP_I2C_STATUS_RESET 0xfffffc
/* QUP OPERATIONAL FLAGS */
#define QUP_I2C_NACK_FLAG BIT(3)
#define QUP_OUT_NOT_EMPTY BIT(4)
#define QUP_IN_NOT_EMPTY BIT(5)
#define QUP_OUT_FULL BIT(6)
#define QUP_OUT_SVC_FLAG BIT(8)
#define QUP_IN_SVC_FLAG BIT(9)
#define QUP_MX_OUTPUT_DONE BIT(10)
#define QUP_MX_INPUT_DONE BIT(11)
/* I2C mini core related values */
#define QUP_CLOCK_AUTO_GATE BIT(13)
#define I2C_MINI_CORE (2 << 8)
#define I2C_N_VAL 15
/* Most significant word offset in FIFO port */
#define QUP_MSW_SHIFT (I2C_N_VAL + 1)
/* Packing/Unpacking words in FIFOs, and IO modes */
#define QUP_OUTPUT_BLK_MODE (1 << 10)
#define QUP_INPUT_BLK_MODE (1 << 12)
#define QUP_UNPACK_EN BIT(14)
#define QUP_PACK_EN BIT(15)
#define QUP_REPACK_EN (QUP_UNPACK_EN | QUP_PACK_EN)
#define QUP_OUTPUT_BLOCK_SIZE(x)(((x) >> 0) & 0x03)
#define QUP_OUTPUT_FIFO_SIZE(x) (((x) >> 2) & 0x07)
#define QUP_INPUT_BLOCK_SIZE(x) (((x) >> 5) & 0x03)
#define QUP_INPUT_FIFO_SIZE(x) (((x) >> 7) & 0x07)
/* QUP tags */
#define QUP_TAG_START (1 << 8)
#define QUP_TAG_DATA (2 << 8)
#define QUP_TAG_STOP (3 << 8)
#define QUP_TAG_REC (4 << 8)
/* Status, Error flags */
#define I2C_STATUS_WR_BUFFER_FULL BIT(0)
#define I2C_STATUS_BUS_ACTIVE BIT(8)
#define I2C_STATUS_ERROR_MASK 0x38000fc
#define QUP_STATUS_ERROR_FLAGS 0x7c
#define QUP_READ_LIMIT 256
#define SET_BIT 0x1
#define RESET_BIT 0x0
#define ONE_BYTE 0x1
struct qup_i2c_dev {
struct device *dev;
void __iomem *base;
int irq;
struct clk *clk;
struct clk *pclk;
struct i2c_adapter adap;
int clk_ctl;
int out_fifo_sz;
int in_fifo_sz;
int out_blk_sz;
int in_blk_sz;
unsigned long one_byte_t;
struct i2c_msg *msg;
/* Current posion in user message buffer */
int pos;
/* I2C protocol errors */
u32 bus_err;
/* QUP core errors */
u32 qup_err;
struct completion xfer;
};
static irqreturn_t qup_i2c_interrupt(int irq, void *dev)
{
struct qup_i2c_dev *qup = dev;
u32 bus_err;
u32 qup_err;
u32 opflags;
bus_err = readl(qup->base + QUP_I2C_STATUS);
qup_err = readl(qup->base + QUP_ERROR_FLAGS);
opflags = readl(qup->base + QUP_OPERATIONAL);
if (!qup->msg) {
/* Clear Error interrupt */
writel(QUP_RESET_STATE, qup->base + QUP_STATE);
return IRQ_HANDLED;
}
bus_err &= I2C_STATUS_ERROR_MASK;
qup_err &= QUP_STATUS_ERROR_FLAGS;
if (qup_err) {
/* Clear Error interrupt */
writel(qup_err, qup->base + QUP_ERROR_FLAGS);
goto done;
}
if (bus_err) {
/* Clear Error interrupt */
writel(QUP_RESET_STATE, qup->base + QUP_STATE);
goto done;
}
if (opflags & QUP_IN_SVC_FLAG)
writel(QUP_IN_SVC_FLAG, qup->base + QUP_OPERATIONAL);
if (opflags & QUP_OUT_SVC_FLAG)
writel(QUP_OUT_SVC_FLAG, qup->base + QUP_OPERATIONAL);
done:
qup->qup_err = qup_err;
qup->bus_err = bus_err;
complete(&qup->xfer);
return IRQ_HANDLED;
}
static int qup_i2c_poll_state_mask(struct qup_i2c_dev *qup,
u32 req_state, u32 req_mask)
{
int retries = 1;
u32 state;
/*
* State transition takes 3 AHB clocks cycles + 3 I2C master clock
* cycles. So retry once after a 1uS delay.
*/
do {
state = readl(qup->base + QUP_STATE);
if (state & QUP_STATE_VALID &&
(state & req_mask) == req_state)
return 0;
udelay(1);
} while (retries--);
return -ETIMEDOUT;
}
static int qup_i2c_poll_state(struct qup_i2c_dev *qup, u32 req_state)
{
return qup_i2c_poll_state_mask(qup, req_state, QUP_STATE_MASK);
}
static int qup_i2c_poll_state_valid(struct qup_i2c_dev *qup)
{
return qup_i2c_poll_state_mask(qup, 0, 0);
}
static int qup_i2c_poll_state_i2c_master(struct qup_i2c_dev *qup)
{
return qup_i2c_poll_state_mask(qup, QUP_I2C_MAST_GEN, QUP_I2C_MAST_GEN);
}
static int qup_i2c_change_state(struct qup_i2c_dev *qup, u32 state)
{
if (qup_i2c_poll_state_valid(qup) != 0)
return -EIO;
writel(state, qup->base + QUP_STATE);
if (qup_i2c_poll_state(qup, state) != 0)
return -EIO;
return 0;
}
/**
* qup_i2c_wait_ready - wait for a give number of bytes in tx/rx path
* @qup: The qup_i2c_dev device
* @op: The bit/event to wait on
* @val: value of the bit to wait on, 0 or 1
* @len: The length the bytes to be transferred
*/
static int qup_i2c_wait_ready(struct qup_i2c_dev *qup, int op, bool val,
int len)
{
unsigned long timeout;
u32 opflags;
u32 status;
u32 shift = __ffs(op);
len *= qup->one_byte_t;
/* timeout after a wait of twice the max time */
timeout = jiffies + len * 4;
for (;;) {
opflags = readl(qup->base + QUP_OPERATIONAL);
status = readl(qup->base + QUP_I2C_STATUS);
if (((opflags & op) >> shift) == val) {
if (op == QUP_OUT_NOT_EMPTY) {
if (!(status & I2C_STATUS_BUS_ACTIVE))
return 0;
} else {
return 0;
}
}
if (time_after(jiffies, timeout))
return -ETIMEDOUT;
usleep_range(len, len * 2);
}
}
static void qup_i2c_set_write_mode(struct qup_i2c_dev *qup, struct i2c_msg *msg)
{
/* Number of entries to shift out, including the start */
int total = msg->len + 1;
if (total < qup->out_fifo_sz) {
/* FIFO mode */
writel(QUP_REPACK_EN, qup->base + QUP_IO_MODE);
writel(total, qup->base + QUP_MX_WRITE_CNT);
} else {
/* BLOCK mode (transfer data on chunks) */
writel(QUP_OUTPUT_BLK_MODE | QUP_REPACK_EN,
qup->base + QUP_IO_MODE);
writel(total, qup->base + QUP_MX_OUTPUT_CNT);
}
}
static int qup_i2c_issue_write(struct qup_i2c_dev *qup, struct i2c_msg *msg)
{
u32 addr = msg->addr << 1;
u32 qup_tag;
int idx;
u32 val;
int ret = 0;
if (qup->pos == 0) {
val = QUP_TAG_START | addr;
idx = 1;
} else {
val = 0;
idx = 0;
}
while (qup->pos < msg->len) {
/* Check that there's space in the FIFO for our pair */
ret = qup_i2c_wait_ready(qup, QUP_OUT_FULL, RESET_BIT,
4 * ONE_BYTE);
if (ret)
return ret;
if (qup->pos == msg->len - 1)
qup_tag = QUP_TAG_STOP;
else
qup_tag = QUP_TAG_DATA;
if (idx & 1)
val |= (qup_tag | msg->buf[qup->pos]) << QUP_MSW_SHIFT;
else
val = qup_tag | msg->buf[qup->pos];
/* Write out the pair and the last odd value */
if (idx & 1 || qup->pos == msg->len - 1)
writel(val, qup->base + QUP_OUT_FIFO_BASE);
qup->pos++;
idx++;
}
return ret;
}
static int qup_i2c_write_one(struct qup_i2c_dev *qup, struct i2c_msg *msg)
{
unsigned long left;
int ret;
qup->msg = msg;
qup->pos = 0;
enable_irq(qup->irq);
qup_i2c_set_write_mode(qup, msg);
ret = qup_i2c_change_state(qup, QUP_RUN_STATE);
if (ret)
goto err;
writel(qup->clk_ctl, qup->base + QUP_I2C_CLK_CTL);
do {
ret = qup_i2c_change_state(qup, QUP_PAUSE_STATE);
if (ret)
goto err;
ret = qup_i2c_issue_write(qup, msg);
if (ret)
goto err;
ret = qup_i2c_change_state(qup, QUP_RUN_STATE);
if (ret)
goto err;
left = wait_for_completion_timeout(&qup->xfer, HZ);
if (!left) {
writel(1, qup->base + QUP_SW_RESET);
ret = -ETIMEDOUT;
goto err;
}
if (qup->bus_err || qup->qup_err) {
if (qup->bus_err & QUP_I2C_NACK_FLAG)
dev_err(qup->dev, "NACK from %x\n", msg->addr);
ret = -EIO;
goto err;
}
} while (qup->pos < msg->len);
/* Wait for the outstanding data in the fifo to drain */
ret = qup_i2c_wait_ready(qup, QUP_OUT_NOT_EMPTY, RESET_BIT, ONE_BYTE);
err:
disable_irq(qup->irq);
qup->msg = NULL;
return ret;
}
static void qup_i2c_set_read_mode(struct qup_i2c_dev *qup, int len)
{
if (len < qup->in_fifo_sz) {
/* FIFO mode */
writel(QUP_REPACK_EN, qup->base + QUP_IO_MODE);
writel(len, qup->base + QUP_MX_READ_CNT);
} else {
/* BLOCK mode (transfer data on chunks) */
writel(QUP_INPUT_BLK_MODE | QUP_REPACK_EN,
qup->base + QUP_IO_MODE);
writel(len, qup->base + QUP_MX_INPUT_CNT);
}
}
static void qup_i2c_issue_read(struct qup_i2c_dev *qup, struct i2c_msg *msg)
{
u32 addr, len, val;
addr = (msg->addr << 1) | 1;
/* 0 is used to specify a length 256 (QUP_READ_LIMIT) */
len = (msg->len == QUP_READ_LIMIT) ? 0 : msg->len;
val = ((QUP_TAG_REC | len) << QUP_MSW_SHIFT) | QUP_TAG_START | addr;
writel(val, qup->base + QUP_OUT_FIFO_BASE);
}
static int qup_i2c_read_fifo(struct qup_i2c_dev *qup, struct i2c_msg *msg)
{
u32 val = 0;
int idx;
int ret = 0;
for (idx = 0; qup->pos < msg->len; idx++) {
if ((idx & 1) == 0) {
/* Check that FIFO have data */
ret = qup_i2c_wait_ready(qup, QUP_IN_NOT_EMPTY,
SET_BIT, 4 * ONE_BYTE);
if (ret)
return ret;
/* Reading 2 words at time */
val = readl(qup->base + QUP_IN_FIFO_BASE);
msg->buf[qup->pos++] = val & 0xFF;
} else {
msg->buf[qup->pos++] = val >> QUP_MSW_SHIFT;
}
}
return ret;
}
static int qup_i2c_read_one(struct qup_i2c_dev *qup, struct i2c_msg *msg)
{
unsigned long left;
int ret;
qup->msg = msg;
qup->pos = 0;
enable_irq(qup->irq);
qup_i2c_set_read_mode(qup, msg->len);
ret = qup_i2c_change_state(qup, QUP_RUN_STATE);
if (ret)
goto err;
writel(qup->clk_ctl, qup->base + QUP_I2C_CLK_CTL);
ret = qup_i2c_change_state(qup, QUP_PAUSE_STATE);
if (ret)
goto err;
qup_i2c_issue_read(qup, msg);
ret = qup_i2c_change_state(qup, QUP_RUN_STATE);
if (ret)
goto err;
do {
left = wait_for_completion_timeout(&qup->xfer, HZ);
if (!left) {
writel(1, qup->base + QUP_SW_RESET);
ret = -ETIMEDOUT;
goto err;
}
if (qup->bus_err || qup->qup_err) {
if (qup->bus_err & QUP_I2C_NACK_FLAG)
dev_err(qup->dev, "NACK from %x\n", msg->addr);
ret = -EIO;
goto err;
}
ret = qup_i2c_read_fifo(qup, msg);
if (ret)
goto err;
} while (qup->pos < msg->len);
err:
disable_irq(qup->irq);
qup->msg = NULL;
return ret;
}
static int qup_i2c_xfer(struct i2c_adapter *adap,
struct i2c_msg msgs[],
int num)
{
struct qup_i2c_dev *qup = i2c_get_adapdata(adap);
int ret, idx;
ret = pm_runtime_get_sync(qup->dev);
if (ret < 0)
goto out;
writel(1, qup->base + QUP_SW_RESET);
ret = qup_i2c_poll_state(qup, QUP_RESET_STATE);
if (ret)
goto out;
/* Configure QUP as I2C mini core */
writel(I2C_MINI_CORE | I2C_N_VAL, qup->base + QUP_CONFIG);
for (idx = 0; idx < num; idx++) {
if (msgs[idx].len == 0) {
ret = -EINVAL;
goto out;
}
if (qup_i2c_poll_state_i2c_master(qup)) {
ret = -EIO;
goto out;
}
if (msgs[idx].flags & I2C_M_RD)
ret = qup_i2c_read_one(qup, &msgs[idx]);
else
ret = qup_i2c_write_one(qup, &msgs[idx]);
if (ret)
break;
ret = qup_i2c_change_state(qup, QUP_RESET_STATE);
if (ret)
break;
}
if (ret == 0)
ret = num;
out:
pm_runtime_mark_last_busy(qup->dev);
pm_runtime_put_autosuspend(qup->dev);
return ret;
}
static u32 qup_i2c_func(struct i2c_adapter *adap)
{
return I2C_FUNC_I2C | (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK);
}
static const struct i2c_algorithm qup_i2c_algo = {
.master_xfer = qup_i2c_xfer,
.functionality = qup_i2c_func,
};
/*
* The QUP block will issue a NACK and STOP on the bus when reaching
* the end of the read, the length of the read is specified as one byte
* which limits the possible read to 256 (QUP_READ_LIMIT) bytes.
*/
static struct i2c_adapter_quirks qup_i2c_quirks = {
.max_read_len = QUP_READ_LIMIT,
};
static void qup_i2c_enable_clocks(struct qup_i2c_dev *qup)
{
clk_prepare_enable(qup->clk);
clk_prepare_enable(qup->pclk);
}
static void qup_i2c_disable_clocks(struct qup_i2c_dev *qup)
{
u32 config;
qup_i2c_change_state(qup, QUP_RESET_STATE);
clk_disable_unprepare(qup->clk);
config = readl(qup->base + QUP_CONFIG);
config |= QUP_CLOCK_AUTO_GATE;
writel(config, qup->base + QUP_CONFIG);
clk_disable_unprepare(qup->pclk);
}
static int qup_i2c_probe(struct platform_device *pdev)
{
static const int blk_sizes[] = {4, 16, 32};
struct device_node *node = pdev->dev.of_node;
struct qup_i2c_dev *qup;
unsigned long one_bit_t;
struct resource *res;
u32 io_mode, hw_ver, size;
int ret, fs_div, hs_div;
int src_clk_freq;
u32 clk_freq = 100000;
qup = devm_kzalloc(&pdev->dev, sizeof(*qup), GFP_KERNEL);
if (!qup)
return -ENOMEM;
qup->dev = &pdev->dev;
init_completion(&qup->xfer);
platform_set_drvdata(pdev, qup);
of_property_read_u32(node, "clock-frequency", &clk_freq);
/* We support frequencies up to FAST Mode (400KHz) */
if (!clk_freq || clk_freq > 400000) {
dev_err(qup->dev, "clock frequency not supported %d\n",
clk_freq);
return -EINVAL;
}
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
qup->base = devm_ioremap_resource(qup->dev, res);
if (IS_ERR(qup->base))
return PTR_ERR(qup->base);
qup->irq = platform_get_irq(pdev, 0);
if (qup->irq < 0) {
dev_err(qup->dev, "No IRQ defined\n");
return qup->irq;
}
qup->clk = devm_clk_get(qup->dev, "core");
if (IS_ERR(qup->clk)) {
dev_err(qup->dev, "Could not get core clock\n");
return PTR_ERR(qup->clk);
}
qup->pclk = devm_clk_get(qup->dev, "iface");
if (IS_ERR(qup->pclk)) {
dev_err(qup->dev, "Could not get iface clock\n");
return PTR_ERR(qup->pclk);
}
qup_i2c_enable_clocks(qup);
/*
* Bootloaders might leave a pending interrupt on certain QUP's,
* so we reset the core before registering for interrupts.
*/
writel(1, qup->base + QUP_SW_RESET);
ret = qup_i2c_poll_state_valid(qup);
if (ret)
goto fail;
ret = devm_request_irq(qup->dev, qup->irq, qup_i2c_interrupt,
IRQF_TRIGGER_HIGH, "i2c_qup", qup);
if (ret) {
dev_err(qup->dev, "Request %d IRQ failed\n", qup->irq);
goto fail;
}
disable_irq(qup->irq);
hw_ver = readl(qup->base + QUP_HW_VERSION);
dev_dbg(qup->dev, "Revision %x\n", hw_ver);
io_mode = readl(qup->base + QUP_IO_MODE);
/*
* The block/fifo size w.r.t. 'actual data' is 1/2 due to 'tag'
* associated with each byte written/received
*/
size = QUP_OUTPUT_BLOCK_SIZE(io_mode);
if (size >= ARRAY_SIZE(blk_sizes)) {
ret = -EIO;
goto fail;
}
qup->out_blk_sz = blk_sizes[size] / 2;
size = QUP_INPUT_BLOCK_SIZE(io_mode);
if (size >= ARRAY_SIZE(blk_sizes)) {
ret = -EIO;
goto fail;
}
qup->in_blk_sz = blk_sizes[size] / 2;
size = QUP_OUTPUT_FIFO_SIZE(io_mode);
qup->out_fifo_sz = qup->out_blk_sz * (2 << size);
size = QUP_INPUT_FIFO_SIZE(io_mode);
qup->in_fifo_sz = qup->in_blk_sz * (2 << size);
src_clk_freq = clk_get_rate(qup->clk);
fs_div = ((src_clk_freq / clk_freq) / 2) - 3;
hs_div = 3;
qup->clk_ctl = (hs_div << 8) | (fs_div & 0xff);
/*
* Time it takes for a byte to be clocked out on the bus.
* Each byte takes 9 clock cycles (8 bits + 1 ack).
*/
one_bit_t = (USEC_PER_SEC / clk_freq) + 1;
qup->one_byte_t = one_bit_t * 9;
dev_dbg(qup->dev, "IN:block:%d, fifo:%d, OUT:block:%d, fifo:%d\n",
qup->in_blk_sz, qup->in_fifo_sz,
qup->out_blk_sz, qup->out_fifo_sz);
i2c_set_adapdata(&qup->adap, qup);
qup->adap.algo = &qup_i2c_algo;
qup->adap.quirks = &qup_i2c_quirks;
qup->adap.dev.parent = qup->dev;
qup->adap.dev.of_node = pdev->dev.of_node;
strlcpy(qup->adap.name, "QUP I2C adapter", sizeof(qup->adap.name));
pm_runtime_set_autosuspend_delay(qup->dev, MSEC_PER_SEC);
pm_runtime_use_autosuspend(qup->dev);
pm_runtime_set_active(qup->dev);
pm_runtime_enable(qup->dev);
ret = i2c_add_adapter(&qup->adap);
if (ret)
goto fail_runtime;
return 0;
fail_runtime:
pm_runtime_disable(qup->dev);
pm_runtime_set_suspended(qup->dev);
fail:
qup_i2c_disable_clocks(qup);
return ret;
}
static int qup_i2c_remove(struct platform_device *pdev)
{
struct qup_i2c_dev *qup = platform_get_drvdata(pdev);
disable_irq(qup->irq);
qup_i2c_disable_clocks(qup);
i2c_del_adapter(&qup->adap);
pm_runtime_disable(qup->dev);
pm_runtime_set_suspended(qup->dev);
return 0;
}
#ifdef CONFIG_PM
static int qup_i2c_pm_suspend_runtime(struct device *device)
{
struct qup_i2c_dev *qup = dev_get_drvdata(device);
dev_dbg(device, "pm_runtime: suspending...\n");
qup_i2c_disable_clocks(qup);
return 0;
}
static int qup_i2c_pm_resume_runtime(struct device *device)
{
struct qup_i2c_dev *qup = dev_get_drvdata(device);
dev_dbg(device, "pm_runtime: resuming...\n");
qup_i2c_enable_clocks(qup);
return 0;
}
#endif
#ifdef CONFIG_PM_SLEEP
static int qup_i2c_suspend(struct device *device)
{
qup_i2c_pm_suspend_runtime(device);
return 0;
}
static int qup_i2c_resume(struct device *device)
{
qup_i2c_pm_resume_runtime(device);
pm_runtime_mark_last_busy(device);
pm_request_autosuspend(device);
return 0;
}
#endif
static const struct dev_pm_ops qup_i2c_qup_pm_ops = {
SET_SYSTEM_SLEEP_PM_OPS(
qup_i2c_suspend,
qup_i2c_resume)
SET_RUNTIME_PM_OPS(
qup_i2c_pm_suspend_runtime,
qup_i2c_pm_resume_runtime,
NULL)
};
static const struct of_device_id qup_i2c_dt_match[] = {
{ .compatible = "qcom,i2c-qup-v1.1.1" },
{ .compatible = "qcom,i2c-qup-v2.1.1" },
{ .compatible = "qcom,i2c-qup-v2.2.1" },
{}
};
MODULE_DEVICE_TABLE(of, qup_i2c_dt_match);
static struct platform_driver qup_i2c_driver = {
.probe = qup_i2c_probe,
.remove = qup_i2c_remove,
.driver = {
.name = "i2c_qup",
.pm = &qup_i2c_qup_pm_ops,
.of_match_table = qup_i2c_dt_match,
},
};
module_platform_driver(qup_i2c_driver);
MODULE_LICENSE("GPL v2");
MODULE_ALIAS("platform:i2c_qup");