AuxXxilium/linux_dsm_epyc7002
1
0
Fork 0
mirror of https://github.com/AuxXxilium/linux_dsm_epyc7002.git synced 2024-12-16 08:58:12 +07:00
Code Issues Actions Packages Projects Releases Wiki Activity
c11113d502
linux_dsm_epyc7002/drivers/mmc/host/sdhci-esdhc-imx.c
Ulf Hansson af5d2b7b0d mmc: sdhci: Drop redundant code for SDIO IRQs 
Nowadays sdhci prevents runtime suspend when SDIO IRQs are enabled.

However, some variants such as sdhci-esdhc-imx's, tries to allow runtime
suspend while having the SDIO IRQs enabled, but without supporting remote
wakeups. This support is a bit questionable, especially if the host device
have a PM domain attached that can be power gated, but more importantly,
the code have also become redundant (which was not the case when it was
introduced).

Rather than keeping the redundant code around, let's drop it and leave this
to be revisited later on.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-09-11 16:10:19 +02:00

1750 lines
50 KiB
C
Raw Blame History

// SPDX-License-Identifier: GPL-2.0
/*
* Freescale eSDHC i.MX controller driver for the platform bus.
*
* derived from the OF-version.
*
* Copyright (c) 2010 Pengutronix e.K.
* Author: Wolfram Sang <kernel@pengutronix.de>
*/
#include <linux/io.h>
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/clk.h>
#include <linux/module.h>
#include <linux/slab.h>
#include <linux/pm_qos.h>
#include <linux/mmc/host.h>
#include <linux/mmc/mmc.h>
#include <linux/mmc/sdio.h>
#include <linux/mmc/slot-gpio.h>
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/pinctrl/consumer.h>
#include <linux/platform_data/mmc-esdhc-imx.h>
#include <linux/pm_runtime.h>
#include "sdhci-pltfm.h"
#include "sdhci-esdhc.h"
#include "cqhci.h"
#define ESDHC_SYS_CTRL_DTOCV_MASK 0x0f
#define ESDHC_CTRL_D3CD 0x08
#define ESDHC_BURST_LEN_EN_INCR (1 << 27)
/* VENDOR SPEC register */
#define ESDHC_VENDOR_SPEC 0xc0
#define ESDHC_VENDOR_SPEC_SDIO_QUIRK (1 << 1)
#define ESDHC_VENDOR_SPEC_VSELECT (1 << 1)
#define ESDHC_VENDOR_SPEC_FRC_SDCLK_ON (1 << 8)
#define ESDHC_WTMK_LVL 0x44
#define ESDHC_WTMK_DEFAULT_VAL 0x10401040
#define ESDHC_WTMK_LVL_RD_WML_MASK 0x000000FF
#define ESDHC_WTMK_LVL_RD_WML_SHIFT 0
#define ESDHC_WTMK_LVL_WR_WML_MASK 0x00FF0000
#define ESDHC_WTMK_LVL_WR_WML_SHIFT 16
#define ESDHC_WTMK_LVL_WML_VAL_DEF 64
#define ESDHC_WTMK_LVL_WML_VAL_MAX 128
#define ESDHC_MIX_CTRL 0x48
#define ESDHC_MIX_CTRL_DDREN (1 << 3)
#define ESDHC_MIX_CTRL_AC23EN (1 << 7)
#define ESDHC_MIX_CTRL_EXE_TUNE (1 << 22)
#define ESDHC_MIX_CTRL_SMPCLK_SEL (1 << 23)
#define ESDHC_MIX_CTRL_AUTO_TUNE_EN (1 << 24)
#define ESDHC_MIX_CTRL_FBCLK_SEL (1 << 25)
#define ESDHC_MIX_CTRL_HS400_EN (1 << 26)
#define ESDHC_MIX_CTRL_HS400_ES_EN (1 << 27)
/* Bits 3 and 6 are not SDHCI standard definitions */
#define ESDHC_MIX_CTRL_SDHCI_MASK 0xb7
/* Tuning bits */
#define ESDHC_MIX_CTRL_TUNING_MASK 0x03c00000
/* dll control register */
#define ESDHC_DLL_CTRL 0x60
#define ESDHC_DLL_OVERRIDE_VAL_SHIFT 9
#define ESDHC_DLL_OVERRIDE_EN_SHIFT 8
/* tune control register */
#define ESDHC_TUNE_CTRL_STATUS 0x68
#define ESDHC_TUNE_CTRL_STEP 1
#define ESDHC_TUNE_CTRL_MIN 0
#define ESDHC_TUNE_CTRL_MAX ((1 << 7) - 1)
/* strobe dll register */
#define ESDHC_STROBE_DLL_CTRL 0x70
#define ESDHC_STROBE_DLL_CTRL_ENABLE (1 << 0)
#define ESDHC_STROBE_DLL_CTRL_RESET (1 << 1)
#define ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT 3
#define ESDHC_STROBE_DLL_CTRL_SLV_UPDATE_INT_DEFAULT (4 << 20)
#define ESDHC_STROBE_DLL_STATUS 0x74
#define ESDHC_STROBE_DLL_STS_REF_LOCK (1 << 1)
#define ESDHC_STROBE_DLL_STS_SLV_LOCK 0x1
#define ESDHC_VEND_SPEC2 0xc8
#define ESDHC_VEND_SPEC2_EN_BUSY_IRQ (1 << 8)
#define ESDHC_TUNING_CTRL 0xcc
#define ESDHC_STD_TUNING_EN (1 << 24)
/* NOTE: the minimum valid tuning start tap for mx6sl is 1 */
#define ESDHC_TUNING_START_TAP_DEFAULT 0x1
#define ESDHC_TUNING_START_TAP_MASK 0xff
#define ESDHC_TUNING_STEP_MASK 0x00070000
#define ESDHC_TUNING_STEP_SHIFT 16
/* pinctrl state */
#define ESDHC_PINCTRL_STATE_100MHZ "state_100mhz"
#define ESDHC_PINCTRL_STATE_200MHZ "state_200mhz"
/*
* Our interpretation of the SDHCI_HOST_CONTROL register
*/
#define ESDHC_CTRL_4BITBUS (0x1 << 1)
#define ESDHC_CTRL_8BITBUS (0x2 << 1)
#define ESDHC_CTRL_BUSWIDTH_MASK (0x3 << 1)
/*
* There is an INT DMA ERR mismatch between eSDHC and STD SDHC SPEC:
* Bit25 is used in STD SPEC, and is reserved in fsl eSDHC design,
* but bit28 is used as the INT DMA ERR in fsl eSDHC design.
* Define this macro DMA error INT for fsl eSDHC
*/
#define ESDHC_INT_VENDOR_SPEC_DMA_ERR (1 << 28)
/* the address offset of CQHCI */
#define ESDHC_CQHCI_ADDR_OFFSET 0x100
/*
* The CMDTYPE of the CMD register (offset 0xE) should be set to
* "11" when the STOP CMD12 is issued on imx53 to abort one
* open ended multi-blk IO. Otherwise the TC INT wouldn't
* be generated.
* In exact block transfer, the controller doesn't complete the
* operations automatically as required at the end of the
* transfer and remains on hold if the abort command is not sent.
* As a result, the TC flag is not asserted and SW received timeout
* exception. Bit1 of Vendor Spec register is used to fix it.
*/
#define ESDHC_FLAG_MULTIBLK_NO_INT BIT(1)
/*
* The flag tells that the ESDHC controller is an USDHC block that is
* integrated on the i.MX6 series.
*/
#define ESDHC_FLAG_USDHC BIT(3)
/* The IP supports manual tuning process */
#define ESDHC_FLAG_MAN_TUNING BIT(4)
/* The IP supports standard tuning process */
#define ESDHC_FLAG_STD_TUNING BIT(5)
/* The IP has SDHCI_CAPABILITIES_1 register */
#define ESDHC_FLAG_HAVE_CAP1 BIT(6)
/*
* The IP has erratum ERR004536
* uSDHC: ADMA Length Mismatch Error occurs if the AHB read access is slow,
* when reading data from the card
* This flag is also set for i.MX25 and i.MX35 in order to get
* SDHCI_QUIRK_BROKEN_ADMA, but for different reasons (ADMA capability bits).
*/
#define ESDHC_FLAG_ERR004536 BIT(7)
/* The IP supports HS200 mode */
#define ESDHC_FLAG_HS200 BIT(8)
/* The IP supports HS400 mode */
#define ESDHC_FLAG_HS400 BIT(9)
/*
* The IP has errata ERR010450
* uSDHC: Due to the I/O timing limit, for SDR mode, SD card clock can't
* exceed 150MHz, for DDR mode, SD card clock can't exceed 45MHz.
*/
#define ESDHC_FLAG_ERR010450 BIT(10)
/* The IP supports HS400ES mode */
#define ESDHC_FLAG_HS400_ES BIT(11)
/* The IP has Host Controller Interface for Command Queuing */
#define ESDHC_FLAG_CQHCI BIT(12)
/* need request pmqos during low power */
#define ESDHC_FLAG_PMQOS BIT(13)
struct esdhc_soc_data {
u32 flags;
};
static const struct esdhc_soc_data esdhc_imx25_data = {
.flags = ESDHC_FLAG_ERR004536,
};
static const struct esdhc_soc_data esdhc_imx35_data = {
.flags = ESDHC_FLAG_ERR004536,
};
static const struct esdhc_soc_data esdhc_imx51_data = {
.flags = 0,
};
static const struct esdhc_soc_data esdhc_imx53_data = {
.flags = ESDHC_FLAG_MULTIBLK_NO_INT,
};
static const struct esdhc_soc_data usdhc_imx6q_data = {
.flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_MAN_TUNING,
};
static const struct esdhc_soc_data usdhc_imx6sl_data = {
.flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
| ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_ERR004536
| ESDHC_FLAG_HS200,
};
static const struct esdhc_soc_data usdhc_imx6sx_data = {
.flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
| ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200,
};
static const struct esdhc_soc_data usdhc_imx6ull_data = {
.flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
| ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
| ESDHC_FLAG_ERR010450,
};
static const struct esdhc_soc_data usdhc_imx7d_data = {
.flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
| ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
| ESDHC_FLAG_HS400,
};
static struct esdhc_soc_data usdhc_imx7ulp_data = {
.flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
| ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
| ESDHC_FLAG_PMQOS | ESDHC_FLAG_HS400,
};
static struct esdhc_soc_data usdhc_imx8qxp_data = {
.flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
| ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
| ESDHC_FLAG_HS400 | ESDHC_FLAG_HS400_ES
| ESDHC_FLAG_CQHCI,
};
struct pltfm_imx_data {
u32 scratchpad;
struct pinctrl *pinctrl;
struct pinctrl_state *pins_default;
struct pinctrl_state *pins_100mhz;
struct pinctrl_state *pins_200mhz;
const struct esdhc_soc_data *socdata;
struct esdhc_platform_data boarddata;
struct clk *clk_ipg;
struct clk *clk_ahb;
struct clk *clk_per;
unsigned int actual_clock;
enum {
NO_CMD_PENDING, /* no multiblock command pending */
MULTIBLK_IN_PROCESS, /* exact multiblock cmd in process */
WAIT_FOR_INT, /* sent CMD12, waiting for response INT */
} multiblock_status;
u32 is_ddr;
struct pm_qos_request pm_qos_req;
};
static const struct platform_device_id imx_esdhc_devtype[] = {
{
.name = "sdhci-esdhc-imx25",
.driver_data = (kernel_ulong_t) &esdhc_imx25_data,
}, {
.name = "sdhci-esdhc-imx35",
.driver_data = (kernel_ulong_t) &esdhc_imx35_data,
}, {
.name = "sdhci-esdhc-imx51",
.driver_data = (kernel_ulong_t) &esdhc_imx51_data,
}, {
/* sentinel */
}
};
MODULE_DEVICE_TABLE(platform, imx_esdhc_devtype);
static const struct of_device_id imx_esdhc_dt_ids[] = {
{ .compatible = "fsl,imx25-esdhc", .data = &esdhc_imx25_data, },
{ .compatible = "fsl,imx35-esdhc", .data = &esdhc_imx35_data, },
{ .compatible = "fsl,imx51-esdhc", .data = &esdhc_imx51_data, },
{ .compatible = "fsl,imx53-esdhc", .data = &esdhc_imx53_data, },
{ .compatible = "fsl,imx6sx-usdhc", .data = &usdhc_imx6sx_data, },
{ .compatible = "fsl,imx6sl-usdhc", .data = &usdhc_imx6sl_data, },
{ .compatible = "fsl,imx6q-usdhc", .data = &usdhc_imx6q_data, },
{ .compatible = "fsl,imx6ull-usdhc", .data = &usdhc_imx6ull_data, },
{ .compatible = "fsl,imx7d-usdhc", .data = &usdhc_imx7d_data, },
{ .compatible = "fsl,imx7ulp-usdhc", .data = &usdhc_imx7ulp_data, },
{ .compatible = "fsl,imx8qxp-usdhc", .data = &usdhc_imx8qxp_data, },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, imx_esdhc_dt_ids);
static inline int is_imx25_esdhc(struct pltfm_imx_data *data)
{
return data->socdata == &esdhc_imx25_data;
}
static inline int is_imx53_esdhc(struct pltfm_imx_data *data)
{
return data->socdata == &esdhc_imx53_data;
}
static inline int is_imx6q_usdhc(struct pltfm_imx_data *data)
{
return data->socdata == &usdhc_imx6q_data;
}
static inline int esdhc_is_usdhc(struct pltfm_imx_data *data)
{
return !!(data->socdata->flags & ESDHC_FLAG_USDHC);
}
static inline void esdhc_clrset_le(struct sdhci_host *host, u32 mask, u32 val, int reg)
{
void __iomem *base = host->ioaddr + (reg & ~0x3);
u32 shift = (reg & 0x3) * 8;
writel(((readl(base) & ~(mask << shift)) | (val << shift)), base);
}
static u32 esdhc_readl_le(struct sdhci_host *host, int reg)
{
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
u32 val = readl(host->ioaddr + reg);
if (unlikely(reg == SDHCI_PRESENT_STATE)) {
u32 fsl_prss = val;
/* save the least 20 bits */
val = fsl_prss & 0x000FFFFF;
/* move dat[0-3] bits */
val |= (fsl_prss & 0x0F000000) >> 4;
/* move cmd line bit */
val |= (fsl_prss & 0x00800000) << 1;
}
if (unlikely(reg == SDHCI_CAPABILITIES)) {
/* ignore bit[0-15] as it stores cap_1 register val for mx6sl */
if (imx_data->socdata->flags & ESDHC_FLAG_HAVE_CAP1)
val &= 0xffff0000;
/* In FSL esdhc IC module, only bit20 is used to indicate the
* ADMA2 capability of esdhc, but this bit is messed up on
* some SOCs (e.g. on MX25, MX35 this bit is set, but they
* don't actually support ADMA2). So set the BROKEN_ADMA
* quirk on MX25/35 platforms.
*/
if (val & SDHCI_CAN_DO_ADMA1) {
val &= ~SDHCI_CAN_DO_ADMA1;
val |= SDHCI_CAN_DO_ADMA2;
}
}
if (unlikely(reg == SDHCI_CAPABILITIES_1)) {
if (esdhc_is_usdhc(imx_data)) {
if (imx_data->socdata->flags & ESDHC_FLAG_HAVE_CAP1)
val = readl(host->ioaddr + SDHCI_CAPABILITIES) & 0xFFFF;
else
/* imx6q/dl does not have cap_1 register, fake one */
val = SDHCI_SUPPORT_DDR50 | SDHCI_SUPPORT_SDR104
| SDHCI_SUPPORT_SDR50
| SDHCI_USE_SDR50_TUNING
| (SDHCI_TUNING_MODE_3 << SDHCI_RETUNING_MODE_SHIFT);
if (imx_data->socdata->flags & ESDHC_FLAG_HS400)
val |= SDHCI_SUPPORT_HS400;
/*
* Do not advertise faster UHS modes if there are no
* pinctrl states for 100MHz/200MHz.
*/
if (IS_ERR_OR_NULL(imx_data->pins_100mhz) ||
IS_ERR_OR_NULL(imx_data->pins_200mhz))
val &= ~(SDHCI_SUPPORT_SDR50 | SDHCI_SUPPORT_DDR50
| SDHCI_SUPPORT_SDR104 | SDHCI_SUPPORT_HS400);
}
}
if (unlikely(reg == SDHCI_MAX_CURRENT) && esdhc_is_usdhc(imx_data)) {
val = 0;
val |= 0xFF << SDHCI_MAX_CURRENT_330_SHIFT;
val |= 0xFF << SDHCI_MAX_CURRENT_300_SHIFT;
val |= 0xFF << SDHCI_MAX_CURRENT_180_SHIFT;
}
if (unlikely(reg == SDHCI_INT_STATUS)) {
if (val & ESDHC_INT_VENDOR_SPEC_DMA_ERR) {
val &= ~ESDHC_INT_VENDOR_SPEC_DMA_ERR;
val |= SDHCI_INT_ADMA_ERROR;
}
/*
* mask off the interrupt we get in response to the manually
* sent CMD12
*/
if ((imx_data->multiblock_status == WAIT_FOR_INT) &&
((val & SDHCI_INT_RESPONSE) == SDHCI_INT_RESPONSE)) {
val &= ~SDHCI_INT_RESPONSE;
writel(SDHCI_INT_RESPONSE, host->ioaddr +
SDHCI_INT_STATUS);
imx_data->multiblock_status = NO_CMD_PENDING;
}
}
return val;
}
static void esdhc_writel_le(struct sdhci_host *host, u32 val, int reg)
{
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
u32 data;
if (unlikely(reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE ||
reg == SDHCI_INT_STATUS)) {
if ((val & SDHCI_INT_CARD_INT) && !esdhc_is_usdhc(imx_data)) {
/*
* Clear and then set D3CD bit to avoid missing the
* card interrupt. This is an eSDHC controller problem
* so we need to apply the following workaround: clear
* and set D3CD bit will make eSDHC re-sample the card
* interrupt. In case a card interrupt was lost,
* re-sample it by the following steps.
*/
data = readl(host->ioaddr + SDHCI_HOST_CONTROL);
data &= ~ESDHC_CTRL_D3CD;
writel(data, host->ioaddr + SDHCI_HOST_CONTROL);
data |= ESDHC_CTRL_D3CD;
writel(data, host->ioaddr + SDHCI_HOST_CONTROL);
}
if (val & SDHCI_INT_ADMA_ERROR) {
val &= ~SDHCI_INT_ADMA_ERROR;
val |= ESDHC_INT_VENDOR_SPEC_DMA_ERR;
}
}
if (unlikely((imx_data->socdata->flags & ESDHC_FLAG_MULTIBLK_NO_INT)
&& (reg == SDHCI_INT_STATUS)
&& (val & SDHCI_INT_DATA_END))) {
u32 v;
v = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
v &= ~ESDHC_VENDOR_SPEC_SDIO_QUIRK;
writel(v, host->ioaddr + ESDHC_VENDOR_SPEC);
if (imx_data->multiblock_status == MULTIBLK_IN_PROCESS)
{
/* send a manual CMD12 with RESPTYP=none */
data = MMC_STOP_TRANSMISSION << 24 |
SDHCI_CMD_ABORTCMD << 16;
writel(data, host->ioaddr + SDHCI_TRANSFER_MODE);
imx_data->multiblock_status = WAIT_FOR_INT;
}
}
writel(val, host->ioaddr + reg);
}
static u16 esdhc_readw_le(struct sdhci_host *host, int reg)
{
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
u16 ret = 0;
u32 val;
if (unlikely(reg == SDHCI_HOST_VERSION)) {
reg ^= 2;
if (esdhc_is_usdhc(imx_data)) {
/*
* The usdhc register returns a wrong host version.
* Correct it here.
*/
return SDHCI_SPEC_300;
}
}
if (unlikely(reg == SDHCI_HOST_CONTROL2)) {
val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
if (val & ESDHC_VENDOR_SPEC_VSELECT)
ret |= SDHCI_CTRL_VDD_180;
if (esdhc_is_usdhc(imx_data)) {
if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING)
val = readl(host->ioaddr + ESDHC_MIX_CTRL);
else if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING)
/* the std tuning bits is in ACMD12_ERR for imx6sl */
val = readl(host->ioaddr + SDHCI_AUTO_CMD_STATUS);
}
if (val & ESDHC_MIX_CTRL_EXE_TUNE)
ret |= SDHCI_CTRL_EXEC_TUNING;
if (val & ESDHC_MIX_CTRL_SMPCLK_SEL)
ret |= SDHCI_CTRL_TUNED_CLK;
ret &= ~SDHCI_CTRL_PRESET_VAL_ENABLE;
return ret;
}
if (unlikely(reg == SDHCI_TRANSFER_MODE)) {
if (esdhc_is_usdhc(imx_data)) {
u32 m = readl(host->ioaddr + ESDHC_MIX_CTRL);
ret = m & ESDHC_MIX_CTRL_SDHCI_MASK;
/* Swap AC23 bit */
if (m & ESDHC_MIX_CTRL_AC23EN) {
ret &= ~ESDHC_MIX_CTRL_AC23EN;
ret |= SDHCI_TRNS_AUTO_CMD23;
}
} else {
ret = readw(host->ioaddr + SDHCI_TRANSFER_MODE);
}
return ret;
}
return readw(host->ioaddr + reg);
}
static void esdhc_writew_le(struct sdhci_host *host, u16 val, int reg)
{
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
u32 new_val = 0;
switch (reg) {
case SDHCI_CLOCK_CONTROL:
new_val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
if (val & SDHCI_CLOCK_CARD_EN)
new_val |= ESDHC_VENDOR_SPEC_FRC_SDCLK_ON;
else
new_val &= ~ESDHC_VENDOR_SPEC_FRC_SDCLK_ON;
writel(new_val, host->ioaddr + ESDHC_VENDOR_SPEC);
return;
case SDHCI_HOST_CONTROL2:
new_val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
if (val & SDHCI_CTRL_VDD_180)
new_val |= ESDHC_VENDOR_SPEC_VSELECT;
else
new_val &= ~ESDHC_VENDOR_SPEC_VSELECT;
writel(new_val, host->ioaddr + ESDHC_VENDOR_SPEC);
if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING) {
new_val = readl(host->ioaddr + ESDHC_MIX_CTRL);
if (val & SDHCI_CTRL_TUNED_CLK) {
new_val |= ESDHC_MIX_CTRL_SMPCLK_SEL;
new_val |= ESDHC_MIX_CTRL_AUTO_TUNE_EN;
} else {
new_val &= ~ESDHC_MIX_CTRL_SMPCLK_SEL;
new_val &= ~ESDHC_MIX_CTRL_AUTO_TUNE_EN;
}
writel(new_val , host->ioaddr + ESDHC_MIX_CTRL);
} else if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING) {
u32 v = readl(host->ioaddr + SDHCI_AUTO_CMD_STATUS);
u32 m = readl(host->ioaddr + ESDHC_MIX_CTRL);
if (val & SDHCI_CTRL_TUNED_CLK) {
v |= ESDHC_MIX_CTRL_SMPCLK_SEL;
} else {
v &= ~ESDHC_MIX_CTRL_SMPCLK_SEL;
m &= ~ESDHC_MIX_CTRL_FBCLK_SEL;
m &= ~ESDHC_MIX_CTRL_AUTO_TUNE_EN;
}
if (val & SDHCI_CTRL_EXEC_TUNING) {
v |= ESDHC_MIX_CTRL_EXE_TUNE;
m |= ESDHC_MIX_CTRL_FBCLK_SEL;
m |= ESDHC_MIX_CTRL_AUTO_TUNE_EN;
} else {
v &= ~ESDHC_MIX_CTRL_EXE_TUNE;
}
writel(v, host->ioaddr + SDHCI_AUTO_CMD_STATUS);
writel(m, host->ioaddr + ESDHC_MIX_CTRL);
}
return;
case SDHCI_TRANSFER_MODE:
if ((imx_data->socdata->flags & ESDHC_FLAG_MULTIBLK_NO_INT)
&& (host->cmd->opcode == SD_IO_RW_EXTENDED)
&& (host->cmd->data->blocks > 1)
&& (host->cmd->data->flags & MMC_DATA_READ)) {
u32 v;
v = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
v |= ESDHC_VENDOR_SPEC_SDIO_QUIRK;
writel(v, host->ioaddr + ESDHC_VENDOR_SPEC);
}
if (esdhc_is_usdhc(imx_data)) {
u32 wml;
u32 m = readl(host->ioaddr + ESDHC_MIX_CTRL);
/* Swap AC23 bit */
if (val & SDHCI_TRNS_AUTO_CMD23) {
val &= ~SDHCI_TRNS_AUTO_CMD23;
val |= ESDHC_MIX_CTRL_AC23EN;
}
m = val | (m & ~ESDHC_MIX_CTRL_SDHCI_MASK);
writel(m, host->ioaddr + ESDHC_MIX_CTRL);
/* Set watermark levels for PIO access to maximum value
* (128 words) to accommodate full 512 bytes buffer.
* For DMA access restore the levels to default value.
*/
m = readl(host->ioaddr + ESDHC_WTMK_LVL);
if (val & SDHCI_TRNS_DMA)
wml = ESDHC_WTMK_LVL_WML_VAL_DEF;
else
wml = ESDHC_WTMK_LVL_WML_VAL_MAX;
m &= ~(ESDHC_WTMK_LVL_RD_WML_MASK |
ESDHC_WTMK_LVL_WR_WML_MASK);
m |= (wml << ESDHC_WTMK_LVL_RD_WML_SHIFT) |
(wml << ESDHC_WTMK_LVL_WR_WML_SHIFT);
writel(m, host->ioaddr + ESDHC_WTMK_LVL);
} else {
/*
* Postpone this write, we must do it together with a
* command write that is down below.
*/
imx_data->scratchpad = val;
}
return;
case SDHCI_COMMAND:
if (host->cmd->opcode == MMC_STOP_TRANSMISSION)
val |= SDHCI_CMD_ABORTCMD;
if ((host->cmd->opcode == MMC_SET_BLOCK_COUNT) &&
(imx_data->socdata->flags & ESDHC_FLAG_MULTIBLK_NO_INT))
imx_data->multiblock_status = MULTIBLK_IN_PROCESS;
if (esdhc_is_usdhc(imx_data))
writel(val << 16,
host->ioaddr + SDHCI_TRANSFER_MODE);
else
writel(val << 16 | imx_data->scratchpad,
host->ioaddr + SDHCI_TRANSFER_MODE);
return;
case SDHCI_BLOCK_SIZE:
val &= ~SDHCI_MAKE_BLKSZ(0x7, 0);
break;
}
esdhc_clrset_le(host, 0xffff, val, reg);
}
static u8 esdhc_readb_le(struct sdhci_host *host, int reg)
{
u8 ret;
u32 val;
switch (reg) {
case SDHCI_HOST_CONTROL:
val = readl(host->ioaddr + reg);
ret = val & SDHCI_CTRL_LED;
ret |= (val >> 5) & SDHCI_CTRL_DMA_MASK;
ret |= (val & ESDHC_CTRL_4BITBUS);
ret |= (val & ESDHC_CTRL_8BITBUS) << 3;
return ret;
}
return readb(host->ioaddr + reg);
}
static void esdhc_writeb_le(struct sdhci_host *host, u8 val, int reg)
{
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
u32 new_val = 0;
u32 mask;
switch (reg) {
case SDHCI_POWER_CONTROL:
/*
* FSL put some DMA bits here
* If your board has a regulator, code should be here
*/
return;
case SDHCI_HOST_CONTROL:
/* FSL messed up here, so we need to manually compose it. */
new_val = val & SDHCI_CTRL_LED;
/* ensure the endianness */
new_val |= ESDHC_HOST_CONTROL_LE;
/* bits 8&9 are reserved on mx25 */
if (!is_imx25_esdhc(imx_data)) {
/* DMA mode bits are shifted */
new_val |= (val & SDHCI_CTRL_DMA_MASK) << 5;
}
/*
* Do not touch buswidth bits here. This is done in
* esdhc_pltfm_bus_width.
* Do not touch the D3CD bit either which is used for the
* SDIO interrupt erratum workaround.
*/
mask = 0xffff & ~(ESDHC_CTRL_BUSWIDTH_MASK | ESDHC_CTRL_D3CD);
esdhc_clrset_le(host, mask, new_val, reg);
return;
case SDHCI_SOFTWARE_RESET:
if (val & SDHCI_RESET_DATA)
new_val = readl(host->ioaddr + SDHCI_HOST_CONTROL);
break;
}
esdhc_clrset_le(host, 0xff, val, reg);
if (reg == SDHCI_SOFTWARE_RESET) {
if (val & SDHCI_RESET_ALL) {
/*
* The esdhc has a design violation to SDHC spec which
* tells that software reset should not affect card
* detection circuit. But esdhc clears its SYSCTL
* register bits [0..2] during the software reset. This
* will stop those clocks that card detection circuit
* relies on. To work around it, we turn the clocks on
* back to keep card detection circuit functional.
*/
esdhc_clrset_le(host, 0x7, 0x7, ESDHC_SYSTEM_CONTROL);
/*
* The reset on usdhc fails to clear MIX_CTRL register.
* Do it manually here.
*/
if (esdhc_is_usdhc(imx_data)) {
/*
* the tuning bits should be kept during reset
*/
new_val = readl(host->ioaddr + ESDHC_MIX_CTRL);
writel(new_val & ESDHC_MIX_CTRL_TUNING_MASK,
host->ioaddr + ESDHC_MIX_CTRL);
imx_data->is_ddr = 0;
}
} else if (val & SDHCI_RESET_DATA) {
/*
* The eSDHC DAT line software reset clears at least the
* data transfer width on i.MX25, so make sure that the
* Host Control register is unaffected.
*/
esdhc_clrset_le(host, 0xff, new_val,
SDHCI_HOST_CONTROL);
}
}
}
static unsigned int esdhc_pltfm_get_max_clock(struct sdhci_host *host)
{
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
return pltfm_host->clock;
}
static unsigned int esdhc_pltfm_get_min_clock(struct sdhci_host *host)
{
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
return pltfm_host->clock / 256 / 16;
}
static inline void esdhc_pltfm_set_clock(struct sdhci_host *host,
unsigned int clock)
{
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
unsigned int host_clock = pltfm_host->clock;
int ddr_pre_div = imx_data->is_ddr ? 2 : 1;
int pre_div = 1;
int div = 1;
u32 temp, val;
if (esdhc_is_usdhc(imx_data)) {
val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
writel(val & ~ESDHC_VENDOR_SPEC_FRC_SDCLK_ON,
host->ioaddr + ESDHC_VENDOR_SPEC);
}
if (clock == 0) {
host->mmc->actual_clock = 0;
return;
}
/* For i.MX53 eSDHCv3, SYSCTL.SDCLKFS may not be set to 0. */
if (is_imx53_esdhc(imx_data)) {
/*
* According to the i.MX53 reference manual, if DLLCTRL[10] can
* be set, then the controller is eSDHCv3, else it is eSDHCv2.
*/
val = readl(host->ioaddr + ESDHC_DLL_CTRL);
writel(val | BIT(10), host->ioaddr + ESDHC_DLL_CTRL);
temp = readl(host->ioaddr + ESDHC_DLL_CTRL);
writel(val, host->ioaddr + ESDHC_DLL_CTRL);
if (temp & BIT(10))
pre_div = 2;
}
temp = sdhci_readl(host, ESDHC_SYSTEM_CONTROL);
temp &= ~(ESDHC_CLOCK_IPGEN | ESDHC_CLOCK_HCKEN | ESDHC_CLOCK_PEREN
| ESDHC_CLOCK_MASK);
sdhci_writel(host, temp, ESDHC_SYSTEM_CONTROL);
if (imx_data->socdata->flags & ESDHC_FLAG_ERR010450) {
unsigned int max_clock;
max_clock = imx_data->is_ddr ? 45000000 : 150000000;
clock = min(clock, max_clock);
}
while (host_clock / (16 * pre_div * ddr_pre_div) > clock &&
pre_div < 256)
pre_div *= 2;
while (host_clock / (div * pre_div * ddr_pre_div) > clock && div < 16)
div++;
host->mmc->actual_clock = host_clock / (div * pre_div * ddr_pre_div);
dev_dbg(mmc_dev(host->mmc), "desired SD clock: %d, actual: %d\n",
clock, host->mmc->actual_clock);
pre_div >>= 1;
div--;
temp = sdhci_readl(host, ESDHC_SYSTEM_CONTROL);
temp |= (ESDHC_CLOCK_IPGEN | ESDHC_CLOCK_HCKEN | ESDHC_CLOCK_PEREN
| (div << ESDHC_DIVIDER_SHIFT)
| (pre_div << ESDHC_PREDIV_SHIFT));
sdhci_writel(host, temp, ESDHC_SYSTEM_CONTROL);
if (esdhc_is_usdhc(imx_data)) {
val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
writel(val | ESDHC_VENDOR_SPEC_FRC_SDCLK_ON,
host->ioaddr + ESDHC_VENDOR_SPEC);
}
mdelay(1);
}
static unsigned int esdhc_pltfm_get_ro(struct sdhci_host *host)
{
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
struct esdhc_platform_data *boarddata = &imx_data->boarddata;
switch (boarddata->wp_type) {
case ESDHC_WP_GPIO:
return mmc_gpio_get_ro(host->mmc);
case ESDHC_WP_CONTROLLER:
return !(readl(host->ioaddr + SDHCI_PRESENT_STATE) &
SDHCI_WRITE_PROTECT);
case ESDHC_WP_NONE:
break;
}
return -ENOSYS;
}
static void esdhc_pltfm_set_bus_width(struct sdhci_host *host, int width)
{
u32 ctrl;
switch (width) {
case MMC_BUS_WIDTH_8:
ctrl = ESDHC_CTRL_8BITBUS;
break;
case MMC_BUS_WIDTH_4:
ctrl = ESDHC_CTRL_4BITBUS;
break;
default:
ctrl = 0;
break;
}
esdhc_clrset_le(host, ESDHC_CTRL_BUSWIDTH_MASK, ctrl,
SDHCI_HOST_CONTROL);
}
static int usdhc_execute_tuning(struct mmc_host *mmc, u32 opcode)
{
struct sdhci_host *host = mmc_priv(mmc);
/*
* i.MX uSDHC internally already uses a fixed optimized timing for
* DDR50, normally does not require tuning for DDR50 mode.
*/
if (host->timing == MMC_TIMING_UHS_DDR50)
return 0;
return sdhci_execute_tuning(mmc, opcode);
}
static void esdhc_prepare_tuning(struct sdhci_host *host, u32 val)
{
u32 reg;
/* FIXME: delay a bit for card to be ready for next tuning due to errors */
mdelay(1);
reg = readl(host->ioaddr + ESDHC_MIX_CTRL);
reg |= ESDHC_MIX_CTRL_EXE_TUNE | ESDHC_MIX_CTRL_SMPCLK_SEL |
ESDHC_MIX_CTRL_FBCLK_SEL;
writel(reg, host->ioaddr + ESDHC_MIX_CTRL);
writel(val << 8, host->ioaddr + ESDHC_TUNE_CTRL_STATUS);
dev_dbg(mmc_dev(host->mmc),
"tuning with delay 0x%x ESDHC_TUNE_CTRL_STATUS 0x%x\n",
val, readl(host->ioaddr + ESDHC_TUNE_CTRL_STATUS));
}
static void esdhc_post_tuning(struct sdhci_host *host)
{
u32 reg;
reg = readl(host->ioaddr + ESDHC_MIX_CTRL);
reg &= ~ESDHC_MIX_CTRL_EXE_TUNE;
reg |= ESDHC_MIX_CTRL_AUTO_TUNE_EN;
writel(reg, host->ioaddr + ESDHC_MIX_CTRL);
}
static int esdhc_executing_tuning(struct sdhci_host *host, u32 opcode)
{
int min, max, avg, ret;
/* find the mininum delay first which can pass tuning */
min = ESDHC_TUNE_CTRL_MIN;
while (min < ESDHC_TUNE_CTRL_MAX) {
esdhc_prepare_tuning(host, min);
if (!mmc_send_tuning(host->mmc, opcode, NULL))
break;
min += ESDHC_TUNE_CTRL_STEP;
}
/* find the maxinum delay which can not pass tuning */
max = min + ESDHC_TUNE_CTRL_STEP;
while (max < ESDHC_TUNE_CTRL_MAX) {
esdhc_prepare_tuning(host, max);
if (mmc_send_tuning(host->mmc, opcode, NULL)) {
max -= ESDHC_TUNE_CTRL_STEP;
break;
}
max += ESDHC_TUNE_CTRL_STEP;
}
/* use average delay to get the best timing */
avg = (min + max) / 2;
esdhc_prepare_tuning(host, avg);
ret = mmc_send_tuning(host->mmc, opcode, NULL);
esdhc_post_tuning(host);
dev_dbg(mmc_dev(host->mmc), "tuning %s at 0x%x ret %d\n",
ret ? "failed" : "passed", avg, ret);
return ret;
}
static void esdhc_hs400_enhanced_strobe(struct mmc_host *mmc, struct mmc_ios *ios)
{
struct sdhci_host *host = mmc_priv(mmc);
u32 m;
m = readl(host->ioaddr + ESDHC_MIX_CTRL);
if (ios->enhanced_strobe)
m |= ESDHC_MIX_CTRL_HS400_ES_EN;
else
m &= ~ESDHC_MIX_CTRL_HS400_ES_EN;
writel(m, host->ioaddr + ESDHC_MIX_CTRL);
}
static int esdhc_change_pinstate(struct sdhci_host *host,
unsigned int uhs)
{
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
struct pinctrl_state *pinctrl;
dev_dbg(mmc_dev(host->mmc), "change pinctrl state for uhs %d\n", uhs);
if (IS_ERR(imx_data->pinctrl) ||
IS_ERR(imx_data->pins_default) ||
IS_ERR(imx_data->pins_100mhz) ||
IS_ERR(imx_data->pins_200mhz))
return -EINVAL;
switch (uhs) {
case MMC_TIMING_UHS_SDR50:
case MMC_TIMING_UHS_DDR50:
pinctrl = imx_data->pins_100mhz;
break;
case MMC_TIMING_UHS_SDR104:
case MMC_TIMING_MMC_HS200:
case MMC_TIMING_MMC_HS400:
pinctrl = imx_data->pins_200mhz;
break;
default:
/* back to default state for other legacy timing */
pinctrl = imx_data->pins_default;
}
return pinctrl_select_state(imx_data->pinctrl, pinctrl);
}
/*
* For HS400 eMMC, there is a data_strobe line. This signal is generated
* by the device and used for data output and CRC status response output
* in HS400 mode. The frequency of this signal follows the frequency of
* CLK generated by host. The host receives the data which is aligned to the
* edge of data_strobe line. Due to the time delay between CLK line and
* data_strobe line, if the delay time is larger than one clock cycle,
* then CLK and data_strobe line will be misaligned, read error shows up.
*/
static void esdhc_set_strobe_dll(struct sdhci_host *host)
{
u32 v;
/* disable clock before enabling strobe dll */
writel(readl(host->ioaddr + ESDHC_VENDOR_SPEC) &
~ESDHC_VENDOR_SPEC_FRC_SDCLK_ON,
host->ioaddr + ESDHC_VENDOR_SPEC);
/* force a reset on strobe dll */
writel(ESDHC_STROBE_DLL_CTRL_RESET,
host->ioaddr + ESDHC_STROBE_DLL_CTRL);
/* clear the reset bit on strobe dll before any setting */
writel(0, host->ioaddr + ESDHC_STROBE_DLL_CTRL);
/*
* enable strobe dll ctrl and adjust the delay target
* for the uSDHC loopback read clock
*/
v = ESDHC_STROBE_DLL_CTRL_ENABLE |
ESDHC_STROBE_DLL_CTRL_SLV_UPDATE_INT_DEFAULT |
(7 << ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT);
writel(v, host->ioaddr + ESDHC_STROBE_DLL_CTRL);
/* wait 5us to make sure strobe dll status register stable */
udelay(5);
v = readl(host->ioaddr + ESDHC_STROBE_DLL_STATUS);
if (!(v & ESDHC_STROBE_DLL_STS_REF_LOCK))
dev_warn(mmc_dev(host->mmc),
"warning! HS400 strobe DLL status REF not lock!\n");
if (!(v & ESDHC_STROBE_DLL_STS_SLV_LOCK))
dev_warn(mmc_dev(host->mmc),
"warning! HS400 strobe DLL status SLV not lock!\n");
}
static void esdhc_reset_tuning(struct sdhci_host *host)
{
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
u32 ctrl;
/* Reset the tuning circuit */
if (esdhc_is_usdhc(imx_data)) {
if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING) {
ctrl = readl(host->ioaddr + ESDHC_MIX_CTRL);
ctrl &= ~ESDHC_MIX_CTRL_SMPCLK_SEL;
ctrl &= ~ESDHC_MIX_CTRL_FBCLK_SEL;
writel(ctrl, host->ioaddr + ESDHC_MIX_CTRL);
writel(0, host->ioaddr + ESDHC_TUNE_CTRL_STATUS);
} else if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING) {
ctrl = readl(host->ioaddr + SDHCI_AUTO_CMD_STATUS);
ctrl &= ~ESDHC_MIX_CTRL_SMPCLK_SEL;
writel(ctrl, host->ioaddr + SDHCI_AUTO_CMD_STATUS);
}
}
}
static void esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned timing)
{
u32 m;
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
struct esdhc_platform_data *boarddata = &imx_data->boarddata;
/* disable ddr mode and disable HS400 mode */
m = readl(host->ioaddr + ESDHC_MIX_CTRL);
m &= ~(ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN);
imx_data->is_ddr = 0;
switch (timing) {
case MMC_TIMING_UHS_SDR12:
case MMC_TIMING_UHS_SDR25:
case MMC_TIMING_UHS_SDR50:
case MMC_TIMING_UHS_SDR104:
case MMC_TIMING_MMC_HS:
case MMC_TIMING_MMC_HS200:
writel(m, host->ioaddr + ESDHC_MIX_CTRL);
break;
case MMC_TIMING_UHS_DDR50:
case MMC_TIMING_MMC_DDR52:
m |= ESDHC_MIX_CTRL_DDREN;
writel(m, host->ioaddr + ESDHC_MIX_CTRL);
imx_data->is_ddr = 1;
if (boarddata->delay_line) {
u32 v;
v = boarddata->delay_line <<
ESDHC_DLL_OVERRIDE_VAL_SHIFT |
(1 << ESDHC_DLL_OVERRIDE_EN_SHIFT);
if (is_imx53_esdhc(imx_data))
v <<= 1;
writel(v, host->ioaddr + ESDHC_DLL_CTRL);
}
break;
case MMC_TIMING_MMC_HS400:
m |= ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN;
writel(m, host->ioaddr + ESDHC_MIX_CTRL);
imx_data->is_ddr = 1;
/* update clock after enable DDR for strobe DLL lock */
host->ops->set_clock(host, host->clock);
esdhc_set_strobe_dll(host);
break;
case MMC_TIMING_LEGACY:
default:
esdhc_reset_tuning(host);
break;
}
esdhc_change_pinstate(host, timing);
}
static void esdhc_reset(struct sdhci_host *host, u8 mask)
{
sdhci_reset(host, mask);
sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
}
static unsigned int esdhc_get_max_timeout_count(struct sdhci_host *host)
{
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
/* Doc Erratum: the uSDHC actual maximum timeout count is 1 << 29 */
return esdhc_is_usdhc(imx_data) ? 1 << 29 : 1 << 27;
}
static void esdhc_set_timeout(struct sdhci_host *host, struct mmc_command *cmd)
{
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
/* use maximum timeout counter */
esdhc_clrset_le(host, ESDHC_SYS_CTRL_DTOCV_MASK,
esdhc_is_usdhc(imx_data) ? 0xF : 0xE,
SDHCI_TIMEOUT_CONTROL);
}
static u32 esdhc_cqhci_irq(struct sdhci_host *host, u32 intmask)
{
int cmd_error = 0;
int data_error = 0;
if (!sdhci_cqe_irq(host, intmask, &cmd_error, &data_error))
return intmask;
cqhci_irq(host->mmc, intmask, cmd_error, data_error);
return 0;
}
static struct sdhci_ops sdhci_esdhc_ops = {
.read_l = esdhc_readl_le,
.read_w = esdhc_readw_le,
.read_b = esdhc_readb_le,
.write_l = esdhc_writel_le,
.write_w = esdhc_writew_le,
.write_b = esdhc_writeb_le,
.set_clock = esdhc_pltfm_set_clock,
.get_max_clock = esdhc_pltfm_get_max_clock,
.get_min_clock = esdhc_pltfm_get_min_clock,
.get_max_timeout_count = esdhc_get_max_timeout_count,
.get_ro = esdhc_pltfm_get_ro,
.set_timeout = esdhc_set_timeout,
.set_bus_width = esdhc_pltfm_set_bus_width,
.set_uhs_signaling = esdhc_set_uhs_signaling,
.reset = esdhc_reset,
.irq = esdhc_cqhci_irq,
};
static const struct sdhci_pltfm_data sdhci_esdhc_imx_pdata = {
.quirks = ESDHC_DEFAULT_QUIRKS | SDHCI_QUIRK_NO_HISPD_BIT
| SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC
| SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC
| SDHCI_QUIRK_BROKEN_CARD_DETECTION,
.ops = &sdhci_esdhc_ops,
};
static void sdhci_esdhc_imx_hwinit(struct sdhci_host *host)
{
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
int tmp;
if (esdhc_is_usdhc(imx_data)) {
/*
* The imx6q ROM code will change the default watermark
* level setting to something insane. Change it back here.
*/
writel(ESDHC_WTMK_DEFAULT_VAL, host->ioaddr + ESDHC_WTMK_LVL);
/*
* ROM code will change the bit burst_length_enable setting
* to zero if this usdhc is chosen to boot system. Change
* it back here, otherwise it will impact the performance a
* lot. This bit is used to enable/disable the burst length
* for the external AHB2AXI bridge. It's useful especially
* for INCR transfer because without burst length indicator,
* the AHB2AXI bridge does not know the burst length in
* advance. And without burst length indicator, AHB INCR
* transfer can only be converted to singles on the AXI side.
*/
writel(readl(host->ioaddr + SDHCI_HOST_CONTROL)
| ESDHC_BURST_LEN_EN_INCR,
host->ioaddr + SDHCI_HOST_CONTROL);
/*
* erratum ESDHC_FLAG_ERR004536 fix for MX6Q TO1.2 and MX6DL
* TO1.1, it's harmless for MX6SL
*/
writel(readl(host->ioaddr + 0x6c) & ~BIT(7),
host->ioaddr + 0x6c);
/* disable DLL_CTRL delay line settings */
writel(0x0, host->ioaddr + ESDHC_DLL_CTRL);
/*
* For the case of command with busy, if set the bit
* ESDHC_VEND_SPEC2_EN_BUSY_IRQ, USDHC will generate a
* transfer complete interrupt when busy is deasserted.
* When CQHCI use DCMD to send a CMD need R1b respons,
* CQHCI require to set ESDHC_VEND_SPEC2_EN_BUSY_IRQ,
* otherwise DCMD will always meet timeout waiting for
* hardware interrupt issue.
*/
if (imx_data->socdata->flags & ESDHC_FLAG_CQHCI) {
tmp = readl(host->ioaddr + ESDHC_VEND_SPEC2);
tmp |= ESDHC_VEND_SPEC2_EN_BUSY_IRQ;
writel(tmp, host->ioaddr + ESDHC_VEND_SPEC2);
host->quirks &= ~SDHCI_QUIRK_NO_BUSY_IRQ;
}
if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING) {
tmp = readl(host->ioaddr + ESDHC_TUNING_CTRL);
tmp |= ESDHC_STD_TUNING_EN |
ESDHC_TUNING_START_TAP_DEFAULT;
if (imx_data->boarddata.tuning_start_tap) {
tmp &= ~ESDHC_TUNING_START_TAP_MASK;
tmp |= imx_data->boarddata.tuning_start_tap;
}
if (imx_data->boarddata.tuning_step) {
tmp &= ~ESDHC_TUNING_STEP_MASK;
tmp |= imx_data->boarddata.tuning_step
<< ESDHC_TUNING_STEP_SHIFT;
}
writel(tmp, host->ioaddr + ESDHC_TUNING_CTRL);
} else if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING) {
/*
* ESDHC_STD_TUNING_EN may be configed in bootloader
* or ROM code, so clear this bit here to make sure
* the manual tuning can work.
*/
tmp = readl(host->ioaddr + ESDHC_TUNING_CTRL);
tmp &= ~ESDHC_STD_TUNING_EN;
writel(tmp, host->ioaddr + ESDHC_TUNING_CTRL);
}
}
}
static void esdhc_cqe_enable(struct mmc_host *mmc)
{
struct sdhci_host *host = mmc_priv(mmc);
struct cqhci_host *cq_host = mmc->cqe_private;
u32 reg;
u16 mode;
int count = 10;
/*
* CQE gets stuck if it sees Buffer Read Enable bit set, which can be
* the case after tuning, so ensure the buffer is drained.
*/
reg = sdhci_readl(host, SDHCI_PRESENT_STATE);
while (reg & SDHCI_DATA_AVAILABLE) {
sdhci_readl(host, SDHCI_BUFFER);
reg = sdhci_readl(host, SDHCI_PRESENT_STATE);
if (count-- == 0) {
dev_warn(mmc_dev(host->mmc),
"CQE may get stuck because the Buffer Read Enable bit is set\n");
break;
}
mdelay(1);
}
/*
* Runtime resume will reset the entire host controller, which
* will also clear the DMAEN/BCEN of register ESDHC_MIX_CTRL.
* Here set DMAEN and BCEN when enable CMDQ.
*/
mode = sdhci_readw(host, SDHCI_TRANSFER_MODE);
if (host->flags & SDHCI_REQ_USE_DMA)
mode |= SDHCI_TRNS_DMA;
if (!(host->quirks2 & SDHCI_QUIRK2_SUPPORT_SINGLE))
mode |= SDHCI_TRNS_BLK_CNT_EN;
sdhci_writew(host, mode, SDHCI_TRANSFER_MODE);
/*
* Though Runtime resume reset the entire host controller,
* but do not impact the CQHCI side, need to clear the
* HALT bit, avoid CQHCI stuck in the first request when
* system resume back.
*/
cqhci_writel(cq_host, 0, CQHCI_CTL);
if (cqhci_readl(cq_host, CQHCI_CTL) && CQHCI_HALT)
dev_err(mmc_dev(host->mmc),
"failed to exit halt state when enable CQE\n");
sdhci_cqe_enable(mmc);
}
static void esdhc_sdhci_dumpregs(struct mmc_host *mmc)
{
sdhci_dumpregs(mmc_priv(mmc));
}
static const struct cqhci_host_ops esdhc_cqhci_ops = {
.enable = esdhc_cqe_enable,
.disable = sdhci_cqe_disable,
.dumpregs = esdhc_sdhci_dumpregs,
};
#ifdef CONFIG_OF
static int
sdhci_esdhc_imx_probe_dt(struct platform_device *pdev,
struct sdhci_host *host,
struct pltfm_imx_data *imx_data)
{
struct device_node *np = pdev->dev.of_node;
struct esdhc_platform_data *boarddata = &imx_data->boarddata;
int ret;
if (of_get_property(np, "fsl,wp-controller", NULL))
boarddata->wp_type = ESDHC_WP_CONTROLLER;
/*
* If we have this property, then activate WP check.
* Retrieveing and requesting the actual WP GPIO will happen
* in the call to mmc_of_parse().
*/
if (of_property_read_bool(np, "wp-gpios"))
boarddata->wp_type = ESDHC_WP_GPIO;
of_property_read_u32(np, "fsl,tuning-step", &boarddata->tuning_step);
of_property_read_u32(np, "fsl,tuning-start-tap",
&boarddata->tuning_start_tap);
if (of_find_property(np, "no-1-8-v", NULL))
host->quirks2 |= SDHCI_QUIRK2_NO_1_8_V;
if (of_property_read_u32(np, "fsl,delay-line", &boarddata->delay_line))
boarddata->delay_line = 0;
mmc_of_parse_voltage(np, &host->ocr_mask);
if (esdhc_is_usdhc(imx_data) && !IS_ERR(imx_data->pins_default)) {
imx_data->pins_100mhz = pinctrl_lookup_state(imx_data->pinctrl,
ESDHC_PINCTRL_STATE_100MHZ);
imx_data->pins_200mhz = pinctrl_lookup_state(imx_data->pinctrl,
ESDHC_PINCTRL_STATE_200MHZ);
}
/* call to generic mmc_of_parse to support additional capabilities */
ret = mmc_of_parse(host->mmc);
if (ret)
return ret;
if (mmc_gpio_get_cd(host->mmc) >= 0)
host->quirks &= ~SDHCI_QUIRK_BROKEN_CARD_DETECTION;
return 0;
}
#else
static inline int
sdhci_esdhc_imx_probe_dt(struct platform_device *pdev,
struct sdhci_host *host,
struct pltfm_imx_data *imx_data)
{
return -ENODEV;
}
#endif
static int sdhci_esdhc_imx_probe_nondt(struct platform_device *pdev,
struct sdhci_host *host,
struct pltfm_imx_data *imx_data)
{
struct esdhc_platform_data *boarddata = &imx_data->boarddata;
int err;
if (!host->mmc->parent->platform_data) {
dev_err(mmc_dev(host->mmc), "no board data!\n");
return -EINVAL;
}
imx_data->boarddata = *((struct esdhc_platform_data *)
host->mmc->parent->platform_data);
/* write_protect */
if (boarddata->wp_type == ESDHC_WP_GPIO) {
err = mmc_gpiod_request_ro(host->mmc, "wp", 0, 0, NULL);
if (err) {
dev_err(mmc_dev(host->mmc),
"failed to request write-protect gpio!\n");
return err;
}
host->mmc->caps2 |= MMC_CAP2_RO_ACTIVE_HIGH;
}
/* card_detect */
switch (boarddata->cd_type) {
case ESDHC_CD_GPIO:
err = mmc_gpiod_request_cd(host->mmc, "cd", 0, false, 0, NULL);
if (err) {
dev_err(mmc_dev(host->mmc),
"failed to request card-detect gpio!\n");
return err;
}
/* fall through */
case ESDHC_CD_CONTROLLER:
/* we have a working card_detect back */
host->quirks &= ~SDHCI_QUIRK_BROKEN_CARD_DETECTION;
break;
case ESDHC_CD_PERMANENT:
host->mmc->caps |= MMC_CAP_NONREMOVABLE;
break;
case ESDHC_CD_NONE:
break;
}
switch (boarddata->max_bus_width) {
case 8:
host->mmc->caps |= MMC_CAP_8_BIT_DATA | MMC_CAP_4_BIT_DATA;
break;
case 4:
host->mmc->caps |= MMC_CAP_4_BIT_DATA;
break;
case 1:
default:
host->quirks |= SDHCI_QUIRK_FORCE_1_BIT_DATA;
break;
}
return 0;
}
static int sdhci_esdhc_imx_probe(struct platform_device *pdev)
{
const struct of_device_id *of_id =
of_match_device(imx_esdhc_dt_ids, &pdev->dev);
struct sdhci_pltfm_host *pltfm_host;
struct sdhci_host *host;
struct cqhci_host *cq_host;
int err;
struct pltfm_imx_data *imx_data;
host = sdhci_pltfm_init(pdev, &sdhci_esdhc_imx_pdata,
sizeof(*imx_data));
if (IS_ERR(host))
return PTR_ERR(host);
pltfm_host = sdhci_priv(host);
imx_data = sdhci_pltfm_priv(pltfm_host);
imx_data->socdata = of_id ? of_id->data : (struct esdhc_soc_data *)
pdev->id_entry->driver_data;
if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
pm_qos_add_request(&imx_data->pm_qos_req,
PM_QOS_CPU_DMA_LATENCY, 0);
imx_data->clk_ipg = devm_clk_get(&pdev->dev, "ipg");
if (IS_ERR(imx_data->clk_ipg)) {
err = PTR_ERR(imx_data->clk_ipg);
goto free_sdhci;
}
imx_data->clk_ahb = devm_clk_get(&pdev->dev, "ahb");
if (IS_ERR(imx_data->clk_ahb)) {
err = PTR_ERR(imx_data->clk_ahb);
goto free_sdhci;
}
imx_data->clk_per = devm_clk_get(&pdev->dev, "per");
if (IS_ERR(imx_data->clk_per)) {
err = PTR_ERR(imx_data->clk_per);
goto free_sdhci;
}
pltfm_host->clk = imx_data->clk_per;
pltfm_host->clock = clk_get_rate(pltfm_host->clk);
err = clk_prepare_enable(imx_data->clk_per);
if (err)
goto free_sdhci;
err = clk_prepare_enable(imx_data->clk_ipg);
if (err)
goto disable_per_clk;
err = clk_prepare_enable(imx_data->clk_ahb);
if (err)
goto disable_ipg_clk;
imx_data->pinctrl = devm_pinctrl_get(&pdev->dev);
if (IS_ERR(imx_data->pinctrl)) {
err = PTR_ERR(imx_data->pinctrl);
goto disable_ahb_clk;
}
imx_data->pins_default = pinctrl_lookup_state(imx_data->pinctrl,
PINCTRL_STATE_DEFAULT);
if (IS_ERR(imx_data->pins_default))
dev_warn(mmc_dev(host->mmc), "could not get default state\n");
if (esdhc_is_usdhc(imx_data)) {
host->quirks2 |= SDHCI_QUIRK2_PRESET_VALUE_BROKEN;
host->mmc->caps |= MMC_CAP_1_8V_DDR | MMC_CAP_3_3V_DDR;
if (!(imx_data->socdata->flags & ESDHC_FLAG_HS200))
host->quirks2 |= SDHCI_QUIRK2_BROKEN_HS200;
/* clear tuning bits in case ROM has set it already */
writel(0x0, host->ioaddr + ESDHC_MIX_CTRL);
writel(0x0, host->ioaddr + SDHCI_AUTO_CMD_STATUS);
writel(0x0, host->ioaddr + ESDHC_TUNE_CTRL_STATUS);
/*
* Link usdhc specific mmc_host_ops execute_tuning function,
* to replace the standard one in sdhci_ops.
*/
host->mmc_host_ops.execute_tuning = usdhc_execute_tuning;
}
if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING)
sdhci_esdhc_ops.platform_execute_tuning =
esdhc_executing_tuning;
if (imx_data->socdata->flags & ESDHC_FLAG_ERR004536)
host->quirks |= SDHCI_QUIRK_BROKEN_ADMA;
if (imx_data->socdata->flags & ESDHC_FLAG_HS400)
host->quirks2 |= SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400;
if (imx_data->socdata->flags & ESDHC_FLAG_HS400_ES) {
host->mmc->caps2 |= MMC_CAP2_HS400_ES;
host->mmc_host_ops.hs400_enhanced_strobe =
esdhc_hs400_enhanced_strobe;
}
if (imx_data->socdata->flags & ESDHC_FLAG_CQHCI) {
host->mmc->caps2 |= MMC_CAP2_CQE | MMC_CAP2_CQE_DCMD;
cq_host = devm_kzalloc(&pdev->dev, sizeof(*cq_host), GFP_KERNEL);
if (!cq_host) {
err = -ENOMEM;
goto disable_ahb_clk;
}
cq_host->mmio = host->ioaddr + ESDHC_CQHCI_ADDR_OFFSET;
cq_host->ops = &esdhc_cqhci_ops;
err = cqhci_init(cq_host, host->mmc, false);
if (err)
goto disable_ahb_clk;
}
if (of_id)
err = sdhci_esdhc_imx_probe_dt(pdev, host, imx_data);
else
err = sdhci_esdhc_imx_probe_nondt(pdev, host, imx_data);
if (err)
goto disable_ahb_clk;
host->tuning_delay = 1;
sdhci_esdhc_imx_hwinit(host);
err = sdhci_add_host(host);
if (err)
goto disable_ahb_clk;
pm_runtime_set_active(&pdev->dev);
pm_runtime_set_autosuspend_delay(&pdev->dev, 50);
pm_runtime_use_autosuspend(&pdev->dev);
pm_suspend_ignore_children(&pdev->dev, 1);
pm_runtime_enable(&pdev->dev);
return 0;
disable_ahb_clk:
clk_disable_unprepare(imx_data->clk_ahb);
disable_ipg_clk:
clk_disable_unprepare(imx_data->clk_ipg);
disable_per_clk:
clk_disable_unprepare(imx_data->clk_per);
free_sdhci:
if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
pm_qos_remove_request(&imx_data->pm_qos_req);
sdhci_pltfm_free(pdev);
return err;
}
static int sdhci_esdhc_imx_remove(struct platform_device *pdev)
{
struct sdhci_host *host = platform_get_drvdata(pdev);
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
int dead = (readl(host->ioaddr + SDHCI_INT_STATUS) == 0xffffffff);
pm_runtime_get_sync(&pdev->dev);
pm_runtime_disable(&pdev->dev);
pm_runtime_put_noidle(&pdev->dev);
sdhci_remove_host(host, dead);
clk_disable_unprepare(imx_data->clk_per);
clk_disable_unprepare(imx_data->clk_ipg);
clk_disable_unprepare(imx_data->clk_ahb);
if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
pm_qos_remove_request(&imx_data->pm_qos_req);
sdhci_pltfm_free(pdev);
return 0;
}
#ifdef CONFIG_PM_SLEEP
static int sdhci_esdhc_suspend(struct device *dev)
{
struct sdhci_host *host = dev_get_drvdata(dev);
int ret;
if (host->mmc->caps2 & MMC_CAP2_CQE) {
ret = cqhci_suspend(host->mmc);
if (ret)
return ret;
}
if (host->tuning_mode != SDHCI_TUNING_MODE_3)
mmc_retune_needed(host->mmc);
return sdhci_suspend_host(host);
}
static int sdhci_esdhc_resume(struct device *dev)
{
struct sdhci_host *host = dev_get_drvdata(dev);
int ret;
/* re-initialize hw state in case it's lost in low power mode */
sdhci_esdhc_imx_hwinit(host);
ret = sdhci_resume_host(host);
if (ret)
return ret;
if (host->mmc->caps2 & MMC_CAP2_CQE)
ret = cqhci_resume(host->mmc);
return ret;
}
#endif
#ifdef CONFIG_PM
static int sdhci_esdhc_runtime_suspend(struct device *dev)
{
struct sdhci_host *host = dev_get_drvdata(dev);
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
int ret;
if (host->mmc->caps2 & MMC_CAP2_CQE) {
ret = cqhci_suspend(host->mmc);
if (ret)
return ret;
}
ret = sdhci_runtime_suspend_host(host);
if (ret)
return ret;
if (host->tuning_mode != SDHCI_TUNING_MODE_3)
mmc_retune_needed(host->mmc);
imx_data->actual_clock = host->mmc->actual_clock;
esdhc_pltfm_set_clock(host, 0);
clk_disable_unprepare(imx_data->clk_per);
clk_disable_unprepare(imx_data->clk_ipg);
clk_disable_unprepare(imx_data->clk_ahb);
if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
pm_qos_remove_request(&imx_data->pm_qos_req);
return ret;
}
static int sdhci_esdhc_runtime_resume(struct device *dev)
{
struct sdhci_host *host = dev_get_drvdata(dev);
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
int err;
if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
pm_qos_add_request(&imx_data->pm_qos_req,
PM_QOS_CPU_DMA_LATENCY, 0);
err = clk_prepare_enable(imx_data->clk_ahb);
if (err)
goto remove_pm_qos_request;
err = clk_prepare_enable(imx_data->clk_per);
if (err)
goto disable_ahb_clk;
err = clk_prepare_enable(imx_data->clk_ipg);
if (err)
goto disable_per_clk;
esdhc_pltfm_set_clock(host, imx_data->actual_clock);
err = sdhci_runtime_resume_host(host, 0);
if (err)
goto disable_ipg_clk;
if (host->mmc->caps2 & MMC_CAP2_CQE)
err = cqhci_resume(host->mmc);
return err;
disable_ipg_clk:
clk_disable_unprepare(imx_data->clk_ipg);
disable_per_clk:
clk_disable_unprepare(imx_data->clk_per);
disable_ahb_clk:
clk_disable_unprepare(imx_data->clk_ahb);
remove_pm_qos_request:
if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
pm_qos_remove_request(&imx_data->pm_qos_req);
return err;
}
#endif
static const struct dev_pm_ops sdhci_esdhc_pmops = {
SET_SYSTEM_SLEEP_PM_OPS(sdhci_esdhc_suspend, sdhci_esdhc_resume)
SET_RUNTIME_PM_OPS(sdhci_esdhc_runtime_suspend,
sdhci_esdhc_runtime_resume, NULL)
};
static struct platform_driver sdhci_esdhc_imx_driver = {
.driver = {
.name = "sdhci-esdhc-imx",
.of_match_table = imx_esdhc_dt_ids,
.pm = &sdhci_esdhc_pmops,
},
.id_table = imx_esdhc_devtype,
.probe = sdhci_esdhc_imx_probe,
.remove = sdhci_esdhc_imx_remove,
};
module_platform_driver(sdhci_esdhc_imx_driver);
MODULE_DESCRIPTION("SDHCI driver for Freescale i.MX eSDHC");
MODULE_AUTHOR("Wolfram Sang <kernel@pengutronix.de>");
MODULE_LICENSE("GPL v2");
Reference in New Issue View Git Blame Copy Permalink