mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-13 17:16:41 +07:00
2db4a76d5f
Implement selftest feature as specified by chip manufacturer. Control: read selftest sysfs entry Response: "OK x y z" or "FAIL x y z" where x, y, and z are difference between selftest mode and normal mode. Test is passed when values are within acceptance limit values. Acceptance limits are provided via platform data. See chip spesifications for acceptance limits. If limits are not properly set, OK / FAIL decision is meaningless. However, userspace application can still make decision based on the numeric x, y, z values. Selftest is meant for HW diagnostic purposes. It is not meant to be called during normal use of the chip. It may cause false interrupt events. Selftest mode delays polling of the normal results but it doesn't cause wrong values. Chip must be in static state during selftest. Any acceration during the test causes most probably failure. Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Acked-by: Éric Piel <Eric.Piel@tremplin-utc.net> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
64 lines
1.9 KiB
C
64 lines
1.9 KiB
C
#ifndef __LIS3LV02D_H_
|
|
#define __LIS3LV02D_H_
|
|
|
|
struct lis3lv02d_platform_data {
|
|
/* please note: the 'click' feature is only supported for
|
|
* LIS[32]02DL variants of the chip and will be ignored for
|
|
* others */
|
|
#define LIS3_CLICK_SINGLE_X (1 << 0)
|
|
#define LIS3_CLICK_DOUBLE_X (1 << 1)
|
|
#define LIS3_CLICK_SINGLE_Y (1 << 2)
|
|
#define LIS3_CLICK_DOUBLE_Y (1 << 3)
|
|
#define LIS3_CLICK_SINGLE_Z (1 << 4)
|
|
#define LIS3_CLICK_DOUBLE_Z (1 << 5)
|
|
unsigned char click_flags;
|
|
unsigned char click_thresh_x;
|
|
unsigned char click_thresh_y;
|
|
unsigned char click_thresh_z;
|
|
unsigned char click_time_limit;
|
|
unsigned char click_latency;
|
|
unsigned char click_window;
|
|
|
|
#define LIS3_IRQ1_DISABLE (0 << 0)
|
|
#define LIS3_IRQ1_FF_WU_1 (1 << 0)
|
|
#define LIS3_IRQ1_FF_WU_2 (2 << 0)
|
|
#define LIS3_IRQ1_FF_WU_12 (3 << 0)
|
|
#define LIS3_IRQ1_DATA_READY (4 << 0)
|
|
#define LIS3_IRQ1_CLICK (7 << 0)
|
|
#define LIS3_IRQ2_DISABLE (0 << 3)
|
|
#define LIS3_IRQ2_FF_WU_1 (1 << 3)
|
|
#define LIS3_IRQ2_FF_WU_2 (2 << 3)
|
|
#define LIS3_IRQ2_FF_WU_12 (3 << 3)
|
|
#define LIS3_IRQ2_DATA_READY (4 << 3)
|
|
#define LIS3_IRQ2_CLICK (7 << 3)
|
|
#define LIS3_IRQ_OPEN_DRAIN (1 << 6)
|
|
#define LIS3_IRQ_ACTIVE_LOW (1 << 7)
|
|
unsigned char irq_cfg;
|
|
|
|
#define LIS3_WAKEUP_X_LO (1 << 0)
|
|
#define LIS3_WAKEUP_X_HI (1 << 1)
|
|
#define LIS3_WAKEUP_Y_LO (1 << 2)
|
|
#define LIS3_WAKEUP_Y_HI (1 << 3)
|
|
#define LIS3_WAKEUP_Z_LO (1 << 4)
|
|
#define LIS3_WAKEUP_Z_HI (1 << 5)
|
|
unsigned char wakeup_flags;
|
|
unsigned char wakeup_thresh;
|
|
#define LIS3_NO_MAP 0
|
|
#define LIS3_DEV_X 1
|
|
#define LIS3_DEV_Y 2
|
|
#define LIS3_DEV_Z 3
|
|
#define LIS3_INV_DEV_X -1
|
|
#define LIS3_INV_DEV_Y -2
|
|
#define LIS3_INV_DEV_Z -3
|
|
s8 axis_x;
|
|
s8 axis_y;
|
|
s8 axis_z;
|
|
int (*setup_resources)(void);
|
|
int (*release_resources)(void);
|
|
/* Limits for selftest are specified in chip data sheet */
|
|
s16 st_min_limits[3]; /* min pass limit x, y, z */
|
|
s16 st_max_limits[3]; /* max pass limit x, y, z */
|
|
};
|
|
|
|
#endif /* __LIS3LV02D_H_ */
|