mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-05 10:06:48 +07:00
dccd573bb0
Minor SPI controller driver updates: make the setup() methods reject spi->mode bits they don't support, by masking aginst the inverse of bits they *do* support. This insures against misbehavior later when new mode bits get added. Most controllers can't support SPI_LSB_FIRST; more handle SPI_CS_HIGH. Support for all four SPI clock/transfer modes is routine. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
144 lines
4.3 KiB
C
144 lines
4.3 KiB
C
#ifndef __SPI_BITBANG_H
|
|
#define __SPI_BITBANG_H
|
|
|
|
/*
|
|
* Mix this utility code with some glue code to get one of several types of
|
|
* simple SPI master driver. Two do polled word-at-a-time I/O:
|
|
*
|
|
* - GPIO/parport bitbangers. Provide chipselect() and txrx_word[](),
|
|
* expanding the per-word routines from the inline templates below.
|
|
*
|
|
* - Drivers for controllers resembling bare shift registers. Provide
|
|
* chipselect() and txrx_word[](), with custom setup()/cleanup() methods
|
|
* that use your controller's clock and chipselect registers.
|
|
*
|
|
* Some hardware works well with requests at spi_transfer scope:
|
|
*
|
|
* - Drivers leveraging smarter hardware, with fifos or DMA; or for half
|
|
* duplex (MicroWire) controllers. Provide chipslect() and txrx_bufs(),
|
|
* and custom setup()/cleanup() methods.
|
|
*/
|
|
struct spi_bitbang {
|
|
struct workqueue_struct *workqueue;
|
|
struct work_struct work;
|
|
|
|
spinlock_t lock;
|
|
struct list_head queue;
|
|
u8 busy;
|
|
u8 use_dma;
|
|
u8 flags; /* extra spi->mode support */
|
|
|
|
struct spi_master *master;
|
|
|
|
/* setup_transfer() changes clock and/or wordsize to match settings
|
|
* for this transfer; zeroes restore defaults from spi_device.
|
|
*/
|
|
int (*setup_transfer)(struct spi_device *spi,
|
|
struct spi_transfer *t);
|
|
|
|
void (*chipselect)(struct spi_device *spi, int is_on);
|
|
#define BITBANG_CS_ACTIVE 1 /* normally nCS, active low */
|
|
#define BITBANG_CS_INACTIVE 0
|
|
|
|
/* txrx_bufs() may handle dma mapping for transfers that don't
|
|
* already have one (transfer.{tx,rx}_dma is zero), or use PIO
|
|
*/
|
|
int (*txrx_bufs)(struct spi_device *spi, struct spi_transfer *t);
|
|
|
|
/* txrx_word[SPI_MODE_*]() just looks like a shift register */
|
|
u32 (*txrx_word[4])(struct spi_device *spi,
|
|
unsigned nsecs,
|
|
u32 word, u8 bits);
|
|
};
|
|
|
|
/* you can call these default bitbang->master methods from your custom
|
|
* methods, if you like.
|
|
*/
|
|
extern int spi_bitbang_setup(struct spi_device *spi);
|
|
extern void spi_bitbang_cleanup(struct spi_device *spi);
|
|
extern int spi_bitbang_transfer(struct spi_device *spi, struct spi_message *m);
|
|
extern int spi_bitbang_setup_transfer(struct spi_device *spi,
|
|
struct spi_transfer *t);
|
|
|
|
/* start or stop queue processing */
|
|
extern int spi_bitbang_start(struct spi_bitbang *spi);
|
|
extern int spi_bitbang_stop(struct spi_bitbang *spi);
|
|
|
|
#endif /* __SPI_BITBANG_H */
|
|
|
|
/*-------------------------------------------------------------------------*/
|
|
|
|
#ifdef EXPAND_BITBANG_TXRX
|
|
|
|
/*
|
|
* The code that knows what GPIO pins do what should have declared four
|
|
* functions, ideally as inlines, before #defining EXPAND_BITBANG_TXRX
|
|
* and including this header:
|
|
*
|
|
* void setsck(struct spi_device *, int is_on);
|
|
* void setmosi(struct spi_device *, int is_on);
|
|
* int getmiso(struct spi_device *);
|
|
* void spidelay(unsigned);
|
|
*
|
|
* A non-inlined routine would call bitbang_txrx_*() routines. The
|
|
* main loop could easily compile down to a handful of instructions,
|
|
* especially if the delay is a NOP (to run at peak speed).
|
|
*
|
|
* Since this is software, the timings may not be exactly what your board's
|
|
* chips need ... there may be several reasons you'd need to tweak timings
|
|
* in these routines, not just make to make it faster or slower to match a
|
|
* particular CPU clock rate.
|
|
*/
|
|
|
|
static inline u32
|
|
bitbang_txrx_be_cpha0(struct spi_device *spi,
|
|
unsigned nsecs, unsigned cpol,
|
|
u32 word, u8 bits)
|
|
{
|
|
/* if (cpol == 0) this is SPI_MODE_0; else this is SPI_MODE_2 */
|
|
|
|
/* clock starts at inactive polarity */
|
|
for (word <<= (32 - bits); likely(bits); bits--) {
|
|
|
|
/* setup MSB (to slave) on trailing edge */
|
|
setmosi(spi, word & (1 << 31));
|
|
spidelay(nsecs); /* T(setup) */
|
|
|
|
setsck(spi, !cpol);
|
|
spidelay(nsecs);
|
|
|
|
/* sample MSB (from slave) on leading edge */
|
|
word <<= 1;
|
|
word |= getmiso(spi);
|
|
setsck(spi, cpol);
|
|
}
|
|
return word;
|
|
}
|
|
|
|
static inline u32
|
|
bitbang_txrx_be_cpha1(struct spi_device *spi,
|
|
unsigned nsecs, unsigned cpol,
|
|
u32 word, u8 bits)
|
|
{
|
|
/* if (cpol == 0) this is SPI_MODE_1; else this is SPI_MODE_3 */
|
|
|
|
/* clock starts at inactive polarity */
|
|
for (word <<= (32 - bits); likely(bits); bits--) {
|
|
|
|
/* setup MSB (to slave) on leading edge */
|
|
setsck(spi, !cpol);
|
|
setmosi(spi, word & (1 << 31));
|
|
spidelay(nsecs); /* T(setup) */
|
|
|
|
setsck(spi, cpol);
|
|
spidelay(nsecs);
|
|
|
|
/* sample MSB (from slave) on trailing edge */
|
|
word <<= 1;
|
|
word |= getmiso(spi);
|
|
}
|
|
return word;
|
|
}
|
|
|
|
#endif /* EXPAND_BITBANG_TXRX */
|