mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-28 11:18:45 +07:00
f4bdfcc29a
This adds and updates the device tree nodes for the MCDE display controller and connects the Samsung display to the TVK1281618 user interface board (UIB) so we get nicely working graphics on this reference design. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
292 lines
7.2 KiB
Plaintext
292 lines
7.2 KiB
Plaintext
/*
|
|
* Copyright 2012 ST-Ericsson AB
|
|
*
|
|
* The code contained herein is licensed under the GNU General Public
|
|
* License. You may obtain a copy of the GNU General Public License
|
|
* Version 2 or later at the following locations:
|
|
*
|
|
* http://www.opensource.org/licenses/gpl-license.html
|
|
* http://www.gnu.org/copyleft/gpl.html
|
|
*
|
|
* Device Tree for the TVK1281618 UIB
|
|
*/
|
|
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
|
|
/ {
|
|
gpio_keys {
|
|
compatible = "gpio-keys";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
vdd-supply = <&ab8500_ldo_aux1_reg>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&prox_tvk_mode>, <&hall_tvk_mode>;
|
|
|
|
button@139 {
|
|
/* Proximity sensor */
|
|
gpios = <&gpio6 25 GPIO_ACTIVE_HIGH>;
|
|
linux,code = <11>; /* SW_FRONT_PROXIMITY */
|
|
label = "SFH7741 Proximity Sensor";
|
|
};
|
|
button@145 {
|
|
/* Hall sensor */
|
|
gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>;
|
|
linux,code = <0>; /* SW_LID */
|
|
label = "HED54XXU11 Hall Effect Sensor";
|
|
};
|
|
};
|
|
|
|
soc {
|
|
i2c@80004000 {
|
|
tc35893@44 {
|
|
compatible = "toshiba,tc35893";
|
|
reg = <0x44>;
|
|
interrupt-parent = <&gpio6>;
|
|
interrupts = <26 IRQ_TYPE_EDGE_RISING>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&tc35893_tvk_mode>;
|
|
|
|
interrupt-controller;
|
|
#interrupt-cells = <1>;
|
|
|
|
tc3589x_gpio {
|
|
compatible = "toshiba,tc3589x-gpio";
|
|
interrupts = <0>;
|
|
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
};
|
|
tc3589x_keypad {
|
|
compatible = "toshiba,tc3589x-keypad";
|
|
interrupts = <6>;
|
|
debounce-delay-ms = <4>;
|
|
keypad,num-columns = <8>;
|
|
keypad,num-rows = <8>;
|
|
linux,no-autorepeat;
|
|
wakeup-source;
|
|
linux,keymap = <0x0301006b
|
|
0x04010066
|
|
0x06040072
|
|
0x040200d7
|
|
0x0303006a
|
|
0x0205000e
|
|
0x0607008b
|
|
0x0500001c
|
|
0x0403000b
|
|
0x03040034
|
|
0x05020067
|
|
0x0305006c
|
|
0x040500e7
|
|
0x0005009e
|
|
0x06020073
|
|
0x01030039
|
|
0x07060069
|
|
0x050500d9>;
|
|
};
|
|
};
|
|
};
|
|
/* Sensors mounted on this board variant */
|
|
i2c@80128000 {
|
|
lsm303dlh@18 {
|
|
/* Accelerometer */
|
|
compatible = "st,lsm303dlh-accel";
|
|
st,drdy-int-pin = <1>;
|
|
drive-open-drain;
|
|
reg = <0x18>;
|
|
vdd-supply = <&ab8500_ldo_aux1_reg>;
|
|
vddio-supply = <&db8500_vsmps2_reg>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&accel_tvk_mode>;
|
|
/*
|
|
* These interrupts cannot be used: the other component
|
|
* ST-Micro L3D4200D gyro that is connected to the same lines
|
|
* cannot set its DRDY line to open drain, so it cannot be
|
|
* shared with other peripherals. The should be defined for
|
|
* the falling edge if they could be wired together.
|
|
*
|
|
* interrupts-extended =
|
|
* <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
|
|
* <&gpio2 19 IRQ_TYPE_EDGE_FALLING>;
|
|
*/
|
|
};
|
|
lsm303dlh@1e {
|
|
/* Magnetometer */
|
|
compatible = "st,lsm303dlh-magn";
|
|
reg = <0x1e>;
|
|
vdd-supply = <&ab8500_ldo_aux1_reg>;
|
|
vddio-supply = <&db8500_vsmps2_reg>;
|
|
/*
|
|
* These interrupts cannot be used: the other component
|
|
* ST-Micro L3D4200D gyro that is connected to the same lines
|
|
* cannot set its DRDY line to open drain, so it cannot be
|
|
* shared with other peripherals. The should be defined for
|
|
* the falling edge if they could be wired together.
|
|
*
|
|
* interrupts-extended =
|
|
* <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
|
|
* <&gpio2 19 IRQ_TYPE_EDGE_FALLING>;
|
|
*/
|
|
};
|
|
lis331dl@1c {
|
|
/* Accelerometer */
|
|
compatible = "st,lis331dl-accel";
|
|
st,drdy-int-pin = <1>;
|
|
reg = <0x1c>;
|
|
vdd-supply = <&ab8500_ldo_aux1_reg>;
|
|
vddio-supply = <&db8500_vsmps2_reg>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&accel_tvk_mode>;
|
|
interrupt-parent = <&gpio2>;
|
|
/* INT2 would need to be open drain */
|
|
interrupts = <18 IRQ_TYPE_EDGE_RISING>,
|
|
<19 IRQ_TYPE_EDGE_RISING>;
|
|
};
|
|
ak8974@f {
|
|
/* Magnetometer */
|
|
compatible = "asahi-kasei,ak8974";
|
|
reg = <0x0f>;
|
|
avdd-supply = <&ab8500_ldo_aux1_reg>;
|
|
dvdd-supply = <&db8500_vsmps2_reg>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&gyro_magn_tvk_mode>;
|
|
/*
|
|
* These interrupts cannot be used: the other component
|
|
* ST-Micro L3D4200D gyro that is connected to the same lines
|
|
* cannot set its DRDY line to open drain, so it cannot be
|
|
* shared with other peripherals. The should be defined for
|
|
* the falling edge if they could be wired together.
|
|
*
|
|
* interrupts-extended =
|
|
* <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
|
|
* <&gpio0 31 IRQ_TYPE_EDGE_FALLING>;
|
|
*/
|
|
};
|
|
l3g4200d@68 {
|
|
/* Gyroscope */
|
|
compatible = "st,l3g4200d-gyro";
|
|
st,drdy-int-pin = <2>;
|
|
reg = <0x68>;
|
|
vdd-supply = <&ab8500_ldo_aux1_reg>;
|
|
vddio-supply = <&db8500_vsmps2_reg>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&gyro_magn_tvk_mode>;
|
|
interrupts-extended =
|
|
<&gpio1 0 IRQ_TYPE_EDGE_RISING>,
|
|
<&gpio0 31 IRQ_TYPE_EDGE_RISING>;
|
|
};
|
|
lsp001wm@5c {
|
|
/* Barometer/pressure sensor */
|
|
compatible = "st,lps001wp-press";
|
|
reg = <0x5c>;
|
|
vdd-supply = <&ab8500_ldo_aux1_reg>;
|
|
vddio-supply = <&db8500_vsmps2_reg>;
|
|
};
|
|
};
|
|
|
|
i2c@80110000 {
|
|
synaptics@4b {
|
|
/* Synaptics RMI4 TM1217 touchscreen */
|
|
compatible = "syna,rmi4-i2c";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <0x4b>;
|
|
vdd-supply = <&ab8500_ldo_aux1_reg>;
|
|
vddio-supply = <&db8500_vsmps2_reg>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&synaptics_tvk_mode>;
|
|
interrupt-parent = <&gpio2>;
|
|
interrupts = <20 IRQ_TYPE_EDGE_FALLING>;
|
|
|
|
rmi-f01@1 {
|
|
reg = <0x1>;
|
|
syna,nosleep = <1>;
|
|
};
|
|
rmi-f11@11 {
|
|
reg = <0x11>;
|
|
touchscreen-inverted-x;
|
|
syna,sensor-type = <1>;
|
|
};
|
|
};
|
|
};
|
|
|
|
pinctrl {
|
|
/* Pull up this GPIO pin */
|
|
tc35893 {
|
|
tc35893_tvk_mode: tc35893_tvk {
|
|
tvk_cfg {
|
|
pins = "GPIO218_AH11";
|
|
ste,config = <&gpio_in_pu>;
|
|
};
|
|
};
|
|
};
|
|
prox {
|
|
prox_tvk_mode: prox_tvk {
|
|
tvk_cfg {
|
|
pins = "GPIO217_AH12";
|
|
ste,config = <&gpio_in_pu>;
|
|
};
|
|
};
|
|
};
|
|
hall {
|
|
hall_tvk_mode: hall_tvk {
|
|
tvk_cfg {
|
|
pins = "GPIO145_C13";
|
|
ste,config = <&gpio_in_pu>;
|
|
};
|
|
};
|
|
};
|
|
accelerometer {
|
|
accel_tvk_mode: accel_tvk {
|
|
/* Accelerometer interrupt lines 1 & 2 */
|
|
tvk_cfg {
|
|
pins = "GPIO82_C1", "GPIO83_D3";
|
|
ste,config = <&gpio_in_pd>;
|
|
};
|
|
};
|
|
};
|
|
gyroscope {
|
|
/*
|
|
* These lines are shared between Gyroscope l3g400dh
|
|
* and AK8974 magnetometer.
|
|
*/
|
|
gyro_magn_tvk_mode: gyro_magn_tvk {
|
|
/* GPIO 31 used for INT pull down the line */
|
|
tvk_cfg1 {
|
|
pins = "GPIO31_V3";
|
|
ste,config = <&gpio_in_pd>;
|
|
};
|
|
/* GPIO 32 used for DRDY, pull this down */
|
|
tvk_cfg2 {
|
|
pins = "GPIO32_V2";
|
|
ste,config = <&gpio_in_pd>;
|
|
};
|
|
};
|
|
};
|
|
synaptics {
|
|
synaptics_tvk_mode: synaptics_tvk {
|
|
/* Touchscreen uses GPIO 84 */
|
|
tvk_cfg1 {
|
|
pins = "GPIO84_C2";
|
|
ste,config = <&gpio_in_pu>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
mcde@a0350000 {
|
|
status = "okay";
|
|
|
|
dsi@a0351000 {
|
|
panel {
|
|
compatible = "samsung,s6d16d0";
|
|
reg = <0>;
|
|
vdd1-supply = <&ab8500_ldo_aux1_reg>;
|
|
reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|