linux_dsm_epyc7002/drivers/net/wireless/ath/wil6210/cfg80211.c
Vladimir Kondratiev 73d839ae50 wil6210: fix for oops while stopping interface
When interface stopped while running intensive Rx traffic, the following oops
observed:

[89846.734683] Call trace:
[89846.737117] [<ffffffc00083aa64>] dev_gro_receive+0xac/0x358
[89846.742674] [<ffffffc00083ae94>] napi_gro_receive+0x24/0xa4
[89846.748251] [<ffffffbffc1c2f88>] $x+0xec/0x1f8 [wil6210]         wil_netif_rx_any
[89846.753547] [<ffffffbffc1c4830>] $x+0x34/0x54 [wil6210]          wil_release_reorder_frame
[89846.758755] [<ffffffbffc1c48ac>] wil_release_reorder_frames+0x5c/0x78 [wil6210]
[89846.766044] [<ffffffbffc1c4bf8>] wil_tid_ampdu_rx_free+0x20/0x48 [wil6210]
[89846.772901] [<ffffffbffc1bedc8>] $x+0x190/0x1e8 [wil6210]
[89846.778285] [<ffffffbffc1c0ed4>] wmi_event_worker+0x230/0x2f8 [wil6210]
[89846.784865] [<ffffffc0000b0bc8>] process_one_work+0x278/0x3fc
[89846.790591] [<ffffffc0000b1218>] worker_thread+0x200/0x330
[89846.796060] [<ffffffc0000b6664>] kthread+0xac/0xb8
[89846.800836] Code: b940c661 f9406a62 8b010041 f9400026 (f8636882)
[89846.807008] ---[ end trace d6fdc17cd27d18f6 ]---

Reason is the following: when removing Rx vring
(wil_netdev_ops.ndo_stop -> wil_stop -> wil_down -> __wil_down -> wil_rx_fini),
Rx interrupt occurs. It trigger Rx NAPI, calling wil_rx_handle() that reaps
(already cleaned) buffer, causing skb referring to garbage memory being set into reorder buffer.
Then, network stack trying to access this buffer and fails.

Prevent Rx NAPI from being scheduled if device going to stop. Bit wil_status_napi_en reflects
NAPI enablement state, check it when triggering Rx NAPI.

Testing shows that check for wil_status_napi_en sometimes gets negative, and new error message
get printed - in this case kernel oops would be observed. Original oops is no more reproducible.

This change requires also changes in the AP flows.
Properly enable/disable NAPI for the AP. Make sure Rx VRING is disabled
when resetting target.

For this, promote __wil_up() and __wil_down() to the module scope, and use it
in the relevant flows.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-11 15:27:39 -04:00

902 lines
23 KiB
C

/*
* Copyright (c) 2012-2014 Qualcomm Atheros, Inc.
*
* Permission to use, copy, modify, and/or distribute this software for any
* purpose with or without fee is hereby granted, provided that the above
* copyright notice and this permission notice appear in all copies.
*
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
*/
#include "wil6210.h"
#include "wmi.h"
#define CHAN60G(_channel, _flags) { \
.band = IEEE80211_BAND_60GHZ, \
.center_freq = 56160 + (2160 * (_channel)), \
.hw_value = (_channel), \
.flags = (_flags), \
.max_antenna_gain = 0, \
.max_power = 40, \
}
static struct ieee80211_channel wil_60ghz_channels[] = {
CHAN60G(1, 0),
CHAN60G(2, 0),
CHAN60G(3, 0),
/* channel 4 not supported yet */
};
static struct ieee80211_supported_band wil_band_60ghz = {
.channels = wil_60ghz_channels,
.n_channels = ARRAY_SIZE(wil_60ghz_channels),
.ht_cap = {
.ht_supported = true,
.cap = 0, /* TODO */
.ampdu_factor = IEEE80211_HT_MAX_AMPDU_64K, /* TODO */
.ampdu_density = IEEE80211_HT_MPDU_DENSITY_8, /* TODO */
.mcs = {
/* MCS 1..12 - SC PHY */
.rx_mask = {0xfe, 0x1f}, /* 1..12 */
.tx_params = IEEE80211_HT_MCS_TX_DEFINED, /* TODO */
},
},
};
static const struct ieee80211_txrx_stypes
wil_mgmt_stypes[NUM_NL80211_IFTYPES] = {
[NL80211_IFTYPE_STATION] = {
.tx = BIT(IEEE80211_STYPE_ACTION >> 4) |
BIT(IEEE80211_STYPE_PROBE_RESP >> 4),
.rx = BIT(IEEE80211_STYPE_ACTION >> 4) |
BIT(IEEE80211_STYPE_PROBE_REQ >> 4)
},
[NL80211_IFTYPE_AP] = {
.tx = BIT(IEEE80211_STYPE_ACTION >> 4) |
BIT(IEEE80211_STYPE_PROBE_RESP >> 4),
.rx = BIT(IEEE80211_STYPE_ACTION >> 4) |
BIT(IEEE80211_STYPE_PROBE_REQ >> 4)
},
[NL80211_IFTYPE_P2P_CLIENT] = {
.tx = BIT(IEEE80211_STYPE_ACTION >> 4) |
BIT(IEEE80211_STYPE_PROBE_RESP >> 4),
.rx = BIT(IEEE80211_STYPE_ACTION >> 4) |
BIT(IEEE80211_STYPE_PROBE_REQ >> 4)
},
[NL80211_IFTYPE_P2P_GO] = {
.tx = BIT(IEEE80211_STYPE_ACTION >> 4) |
BIT(IEEE80211_STYPE_PROBE_RESP >> 4),
.rx = BIT(IEEE80211_STYPE_ACTION >> 4) |
BIT(IEEE80211_STYPE_PROBE_REQ >> 4)
},
};
static const u32 wil_cipher_suites[] = {
WLAN_CIPHER_SUITE_GCMP,
};
int wil_iftype_nl2wmi(enum nl80211_iftype type)
{
static const struct {
enum nl80211_iftype nl;
enum wmi_network_type wmi;
} __nl2wmi[] = {
{NL80211_IFTYPE_ADHOC, WMI_NETTYPE_ADHOC},
{NL80211_IFTYPE_STATION, WMI_NETTYPE_INFRA},
{NL80211_IFTYPE_AP, WMI_NETTYPE_AP},
{NL80211_IFTYPE_P2P_CLIENT, WMI_NETTYPE_P2P},
{NL80211_IFTYPE_P2P_GO, WMI_NETTYPE_P2P},
{NL80211_IFTYPE_MONITOR, WMI_NETTYPE_ADHOC}, /* FIXME */
};
uint i;
for (i = 0; i < ARRAY_SIZE(__nl2wmi); i++) {
if (__nl2wmi[i].nl == type)
return __nl2wmi[i].wmi;
}
return -EOPNOTSUPP;
}
int wil_cid_fill_sinfo(struct wil6210_priv *wil, int cid,
struct station_info *sinfo)
{
struct wmi_notify_req_cmd cmd = {
.cid = cid,
.interval_usec = 0,
};
struct {
struct wil6210_mbox_hdr_wmi wmi;
struct wmi_notify_req_done_event evt;
} __packed reply;
struct wil_net_stats *stats = &wil->sta[cid].stats;
int rc;
rc = wmi_call(wil, WMI_NOTIFY_REQ_CMDID, &cmd, sizeof(cmd),
WMI_NOTIFY_REQ_DONE_EVENTID, &reply, sizeof(reply), 20);
if (rc)
return rc;
wil_dbg_wmi(wil, "Link status for CID %d: {\n"
" MCS %d TSF 0x%016llx\n"
" BF status 0x%08x SNR 0x%08x SQI %d%%\n"
" Tx Tpt %d goodput %d Rx goodput %d\n"
" Sectors(rx:tx) my %d:%d peer %d:%d\n""}\n",
cid, le16_to_cpu(reply.evt.bf_mcs),
le64_to_cpu(reply.evt.tsf), reply.evt.status,
le32_to_cpu(reply.evt.snr_val),
reply.evt.sqi,
le32_to_cpu(reply.evt.tx_tpt),
le32_to_cpu(reply.evt.tx_goodput),
le32_to_cpu(reply.evt.rx_goodput),
le16_to_cpu(reply.evt.my_rx_sector),
le16_to_cpu(reply.evt.my_tx_sector),
le16_to_cpu(reply.evt.other_rx_sector),
le16_to_cpu(reply.evt.other_tx_sector));
sinfo->generation = wil->sinfo_gen;
sinfo->filled = STATION_INFO_RX_BYTES |
STATION_INFO_TX_BYTES |
STATION_INFO_RX_PACKETS |
STATION_INFO_TX_PACKETS |
STATION_INFO_RX_BITRATE |
STATION_INFO_TX_BITRATE |
STATION_INFO_RX_DROP_MISC |
STATION_INFO_TX_FAILED;
sinfo->txrate.flags = RATE_INFO_FLAGS_MCS | RATE_INFO_FLAGS_60G;
sinfo->txrate.mcs = le16_to_cpu(reply.evt.bf_mcs);
sinfo->rxrate.flags = RATE_INFO_FLAGS_MCS | RATE_INFO_FLAGS_60G;
sinfo->rxrate.mcs = stats->last_mcs_rx;
sinfo->rx_bytes = stats->rx_bytes;
sinfo->rx_packets = stats->rx_packets;
sinfo->rx_dropped_misc = stats->rx_dropped;
sinfo->tx_bytes = stats->tx_bytes;
sinfo->tx_packets = stats->tx_packets;
sinfo->tx_failed = stats->tx_errors;
if (test_bit(wil_status_fwconnected, &wil->status)) {
sinfo->filled |= STATION_INFO_SIGNAL;
sinfo->signal = reply.evt.sqi;
}
return rc;
}
static int wil_cfg80211_get_station(struct wiphy *wiphy,
struct net_device *ndev,
const u8 *mac, struct station_info *sinfo)
{
struct wil6210_priv *wil = wiphy_to_wil(wiphy);
int rc;
int cid = wil_find_cid(wil, mac);
wil_dbg_misc(wil, "%s(%pM) CID %d\n", __func__, mac, cid);
if (cid < 0)
return cid;
rc = wil_cid_fill_sinfo(wil, cid, sinfo);
return rc;
}
/*
* Find @idx-th active STA for station dump.
*/
static int wil_find_cid_by_idx(struct wil6210_priv *wil, int idx)
{
int i;
for (i = 0; i < ARRAY_SIZE(wil->sta); i++) {
if (wil->sta[i].status == wil_sta_unused)
continue;
if (idx == 0)
return i;
idx--;
}
return -ENOENT;
}
static int wil_cfg80211_dump_station(struct wiphy *wiphy,
struct net_device *dev, int idx,
u8 *mac, struct station_info *sinfo)
{
struct wil6210_priv *wil = wiphy_to_wil(wiphy);
int rc;
int cid = wil_find_cid_by_idx(wil, idx);
if (cid < 0)
return -ENOENT;
memcpy(mac, wil->sta[cid].addr, ETH_ALEN);
wil_dbg_misc(wil, "%s(%pM) CID %d\n", __func__, mac, cid);
rc = wil_cid_fill_sinfo(wil, cid, sinfo);
return rc;
}
static int wil_cfg80211_change_iface(struct wiphy *wiphy,
struct net_device *ndev,
enum nl80211_iftype type, u32 *flags,
struct vif_params *params)
{
struct wil6210_priv *wil = wiphy_to_wil(wiphy);
struct wireless_dev *wdev = wil->wdev;
switch (type) {
case NL80211_IFTYPE_STATION:
case NL80211_IFTYPE_AP:
case NL80211_IFTYPE_P2P_CLIENT:
case NL80211_IFTYPE_P2P_GO:
break;
case NL80211_IFTYPE_MONITOR:
if (flags)
wil->monitor_flags = *flags;
else
wil->monitor_flags = 0;
break;
default:
return -EOPNOTSUPP;
}
wdev->iftype = type;
return 0;
}
static int wil_cfg80211_scan(struct wiphy *wiphy,
struct cfg80211_scan_request *request)
{
struct wil6210_priv *wil = wiphy_to_wil(wiphy);
struct wireless_dev *wdev = wil->wdev;
struct {
struct wmi_start_scan_cmd cmd;
u16 chnl[4];
} __packed cmd;
uint i, n;
int rc;
if (wil->scan_request) {
wil_err(wil, "Already scanning\n");
return -EAGAIN;
}
/* check we are client side */
switch (wdev->iftype) {
case NL80211_IFTYPE_STATION:
case NL80211_IFTYPE_P2P_CLIENT:
break;
default:
return -EOPNOTSUPP;
}
/* FW don't support scan after connection attempt */
if (test_bit(wil_status_dontscan, &wil->status)) {
wil_err(wil, "Can't scan now\n");
return -EBUSY;
}
wil_dbg_misc(wil, "Start scan_request 0x%p\n", request);
wil->scan_request = request;
mod_timer(&wil->scan_timer, jiffies + WIL6210_SCAN_TO);
memset(&cmd, 0, sizeof(cmd));
cmd.cmd.num_channels = 0;
n = min(request->n_channels, 4U);
for (i = 0; i < n; i++) {
int ch = request->channels[i]->hw_value;
if (ch == 0) {
wil_err(wil,
"Scan requested for unknown frequency %dMhz\n",
request->channels[i]->center_freq);
continue;
}
/* 0-based channel indexes */
cmd.cmd.channel_list[cmd.cmd.num_channels++].channel = ch - 1;
wil_dbg_misc(wil, "Scan for ch %d : %d MHz\n", ch,
request->channels[i]->center_freq);
}
if (request->ie_len)
print_hex_dump_bytes("Scan IE ", DUMP_PREFIX_OFFSET,
request->ie, request->ie_len);
else
wil_dbg_misc(wil, "Scan has no IE's\n");
rc = wmi_set_ie(wil, WMI_FRAME_PROBE_REQ, request->ie_len,
request->ie);
if (rc) {
wil_err(wil, "Aborting scan, set_ie failed: %d\n", rc);
goto out;
}
rc = wmi_send(wil, WMI_START_SCAN_CMDID, &cmd, sizeof(cmd.cmd) +
cmd.cmd.num_channels * sizeof(cmd.cmd.channel_list[0]));
out:
if (rc) {
del_timer_sync(&wil->scan_timer);
wil->scan_request = NULL;
}
return rc;
}
static void wil_print_connect_params(struct wil6210_priv *wil,
struct cfg80211_connect_params *sme)
{
wil_info(wil, "Connecting to:\n");
if (sme->channel) {
wil_info(wil, " Channel: %d freq %d\n",
sme->channel->hw_value, sme->channel->center_freq);
}
if (sme->bssid)
wil_info(wil, " BSSID: %pM\n", sme->bssid);
if (sme->ssid)
print_hex_dump(KERN_INFO, " SSID: ", DUMP_PREFIX_OFFSET,
16, 1, sme->ssid, sme->ssid_len, true);
wil_info(wil, " Privacy: %s\n", sme->privacy ? "secure" : "open");
}
static int wil_cfg80211_connect(struct wiphy *wiphy,
struct net_device *ndev,
struct cfg80211_connect_params *sme)
{
struct wil6210_priv *wil = wiphy_to_wil(wiphy);
struct cfg80211_bss *bss;
struct wmi_connect_cmd conn;
const u8 *ssid_eid;
const u8 *rsn_eid;
int ch;
int rc = 0;
if (test_bit(wil_status_fwconnecting, &wil->status) ||
test_bit(wil_status_fwconnected, &wil->status))
return -EALREADY;
wil_print_connect_params(wil, sme);
bss = cfg80211_get_bss(wiphy, sme->channel, sme->bssid,
sme->ssid, sme->ssid_len,
WLAN_CAPABILITY_ESS, WLAN_CAPABILITY_ESS);
if (!bss) {
wil_err(wil, "Unable to find BSS\n");
return -ENOENT;
}
ssid_eid = ieee80211_bss_get_ie(bss, WLAN_EID_SSID);
if (!ssid_eid) {
wil_err(wil, "No SSID\n");
rc = -ENOENT;
goto out;
}
rsn_eid = sme->ie ?
cfg80211_find_ie(WLAN_EID_RSN, sme->ie, sme->ie_len) :
NULL;
if (rsn_eid) {
if (sme->ie_len > WMI_MAX_IE_LEN) {
rc = -ERANGE;
wil_err(wil, "IE too large (%td bytes)\n",
sme->ie_len);
goto out;
}
/* For secure assoc, send WMI_DELETE_CIPHER_KEY_CMD */
rc = wmi_del_cipher_key(wil, 0, bss->bssid);
if (rc) {
wil_err(wil, "WMI_DELETE_CIPHER_KEY_CMD failed\n");
goto out;
}
}
/* WMI_SET_APPIE_CMD. ie may contain rsn info as well as other info
* elements. Send it also in case it's empty, to erase previously set
* ies in FW.
*/
rc = wmi_set_ie(wil, WMI_FRAME_ASSOC_REQ, sme->ie_len, sme->ie);
if (rc) {
wil_err(wil, "WMI_SET_APPIE_CMD failed\n");
goto out;
}
/* WMI_CONNECT_CMD */
memset(&conn, 0, sizeof(conn));
switch (bss->capability & WLAN_CAPABILITY_DMG_TYPE_MASK) {
case WLAN_CAPABILITY_DMG_TYPE_AP:
conn.network_type = WMI_NETTYPE_INFRA;
break;
case WLAN_CAPABILITY_DMG_TYPE_PBSS:
conn.network_type = WMI_NETTYPE_P2P;
break;
default:
wil_err(wil, "Unsupported BSS type, capability= 0x%04x\n",
bss->capability);
goto out;
}
if (rsn_eid) {
conn.dot11_auth_mode = WMI_AUTH11_SHARED;
conn.auth_mode = WMI_AUTH_WPA2_PSK;
conn.pairwise_crypto_type = WMI_CRYPT_AES_GCMP;
conn.pairwise_crypto_len = 16;
} else {
conn.dot11_auth_mode = WMI_AUTH11_OPEN;
conn.auth_mode = WMI_AUTH_NONE;
}
conn.ssid_len = min_t(u8, ssid_eid[1], 32);
memcpy(conn.ssid, ssid_eid+2, conn.ssid_len);
ch = bss->channel->hw_value;
if (ch == 0) {
wil_err(wil, "BSS at unknown frequency %dMhz\n",
bss->channel->center_freq);
rc = -EOPNOTSUPP;
goto out;
}
conn.channel = ch - 1;
memcpy(conn.bssid, bss->bssid, ETH_ALEN);
memcpy(conn.dst_mac, bss->bssid, ETH_ALEN);
set_bit(wil_status_fwconnecting, &wil->status);
rc = wmi_send(wil, WMI_CONNECT_CMDID, &conn, sizeof(conn));
if (rc == 0) {
/* Connect can take lots of time */
mod_timer(&wil->connect_timer,
jiffies + msecs_to_jiffies(2000));
} else {
clear_bit(wil_status_fwconnecting, &wil->status);
}
out:
cfg80211_put_bss(wiphy, bss);
return rc;
}
static int wil_cfg80211_disconnect(struct wiphy *wiphy,
struct net_device *ndev,
u16 reason_code)
{
int rc;
struct wil6210_priv *wil = wiphy_to_wil(wiphy);
rc = wmi_send(wil, WMI_DISCONNECT_CMDID, NULL, 0);
return rc;
}
int wil_cfg80211_mgmt_tx(struct wiphy *wiphy, struct wireless_dev *wdev,
struct cfg80211_mgmt_tx_params *params,
u64 *cookie)
{
const u8 *buf = params->buf;
size_t len = params->len;
struct wil6210_priv *wil = wiphy_to_wil(wiphy);
int rc;
bool tx_status = false;
struct ieee80211_mgmt *mgmt_frame = (void *)buf;
struct wmi_sw_tx_req_cmd *cmd;
struct {
struct wil6210_mbox_hdr_wmi wmi;
struct wmi_sw_tx_complete_event evt;
} __packed evt;
cmd = kmalloc(sizeof(*cmd) + len, GFP_KERNEL);
if (!cmd) {
rc = -ENOMEM;
goto out;
}
memcpy(cmd->dst_mac, mgmt_frame->da, WMI_MAC_LEN);
cmd->len = cpu_to_le16(len);
memcpy(cmd->payload, buf, len);
rc = wmi_call(wil, WMI_SW_TX_REQ_CMDID, cmd, sizeof(*cmd) + len,
WMI_SW_TX_COMPLETE_EVENTID, &evt, sizeof(evt), 2000);
if (rc == 0)
tx_status = !evt.evt.status;
kfree(cmd);
out:
cfg80211_mgmt_tx_status(wdev, cookie ? *cookie : 0, buf, len,
tx_status, GFP_KERNEL);
return rc;
}
static int wil_cfg80211_set_channel(struct wiphy *wiphy,
struct cfg80211_chan_def *chandef)
{
struct wil6210_priv *wil = wiphy_to_wil(wiphy);
struct wireless_dev *wdev = wil->wdev;
wdev->preset_chandef = *chandef;
return 0;
}
static int wil_cfg80211_add_key(struct wiphy *wiphy,
struct net_device *ndev,
u8 key_index, bool pairwise,
const u8 *mac_addr,
struct key_params *params)
{
struct wil6210_priv *wil = wiphy_to_wil(wiphy);
/* group key is not used */
if (!pairwise)
return 0;
return wmi_add_cipher_key(wil, key_index, mac_addr,
params->key_len, params->key);
}
static int wil_cfg80211_del_key(struct wiphy *wiphy,
struct net_device *ndev,
u8 key_index, bool pairwise,
const u8 *mac_addr)
{
struct wil6210_priv *wil = wiphy_to_wil(wiphy);
/* group key is not used */
if (!pairwise)
return 0;
return wmi_del_cipher_key(wil, key_index, mac_addr);
}
/* Need to be present or wiphy_new() will WARN */
static int wil_cfg80211_set_default_key(struct wiphy *wiphy,
struct net_device *ndev,
u8 key_index, bool unicast,
bool multicast)
{
return 0;
}
static int wil_remain_on_channel(struct wiphy *wiphy,
struct wireless_dev *wdev,
struct ieee80211_channel *chan,
unsigned int duration,
u64 *cookie)
{
struct wil6210_priv *wil = wiphy_to_wil(wiphy);
int rc;
/* TODO: handle duration */
wil_info(wil, "%s(%d, %d ms)\n", __func__, chan->center_freq, duration);
rc = wmi_set_channel(wil, chan->hw_value);
if (rc)
return rc;
rc = wmi_rxon(wil, true);
return rc;
}
static int wil_cancel_remain_on_channel(struct wiphy *wiphy,
struct wireless_dev *wdev,
u64 cookie)
{
struct wil6210_priv *wil = wiphy_to_wil(wiphy);
int rc;
wil_info(wil, "%s()\n", __func__);
rc = wmi_rxon(wil, false);
return rc;
}
static void wil_print_bcon_data(struct cfg80211_beacon_data *b)
{
print_hex_dump_bytes("head ", DUMP_PREFIX_OFFSET,
b->head, b->head_len);
print_hex_dump_bytes("tail ", DUMP_PREFIX_OFFSET,
b->tail, b->tail_len);
print_hex_dump_bytes("BCON IE ", DUMP_PREFIX_OFFSET,
b->beacon_ies, b->beacon_ies_len);
print_hex_dump_bytes("PROBE ", DUMP_PREFIX_OFFSET,
b->probe_resp, b->probe_resp_len);
print_hex_dump_bytes("PROBE IE ", DUMP_PREFIX_OFFSET,
b->proberesp_ies, b->proberesp_ies_len);
print_hex_dump_bytes("ASSOC IE ", DUMP_PREFIX_OFFSET,
b->assocresp_ies, b->assocresp_ies_len);
}
static void wil_print_crypto(struct wil6210_priv *wil,
struct cfg80211_crypto_settings *c)
{
wil_dbg_misc(wil, "WPA versions: 0x%08x cipher group 0x%08x\n",
c->wpa_versions, c->cipher_group);
wil_dbg_misc(wil, "Pairwise ciphers [%d]\n", c->n_ciphers_pairwise);
wil_dbg_misc(wil, "AKM suites [%d]\n", c->n_akm_suites);
wil_dbg_misc(wil, "Control port : %d, eth_type 0x%04x no_encrypt %d\n",
c->control_port, be16_to_cpu(c->control_port_ethertype),
c->control_port_no_encrypt);
}
static int wil_fix_bcon(struct wil6210_priv *wil,
struct cfg80211_beacon_data *bcon)
{
struct ieee80211_mgmt *f = (struct ieee80211_mgmt *)bcon->probe_resp;
size_t hlen = offsetof(struct ieee80211_mgmt, u.probe_resp.variable);
int rc = 0;
if (bcon->probe_resp_len <= hlen)
return 0;
if (!bcon->proberesp_ies) {
bcon->proberesp_ies = f->u.probe_resp.variable;
bcon->proberesp_ies_len = bcon->probe_resp_len - hlen;
rc = 1;
}
if (!bcon->assocresp_ies) {
bcon->assocresp_ies = f->u.probe_resp.variable;
bcon->assocresp_ies_len = bcon->probe_resp_len - hlen;
rc = 1;
}
return rc;
}
static int wil_cfg80211_change_beacon(struct wiphy *wiphy,
struct net_device *ndev,
struct cfg80211_beacon_data *bcon)
{
struct wil6210_priv *wil = wiphy_to_wil(wiphy);
int rc;
wil_dbg_misc(wil, "%s()\n", __func__);
if (wil_fix_bcon(wil, bcon)) {
wil_dbg_misc(wil, "Fixed bcon\n");
wil_print_bcon_data(bcon);
}
/* FW do not form regular beacon, so bcon IE's are not set
* For the DMG bcon, when it will be supported, bcon IE's will
* be reused; add something like:
* wmi_set_ie(wil, WMI_FRAME_BEACON, bcon->beacon_ies_len,
* bcon->beacon_ies);
*/
rc = wmi_set_ie(wil, WMI_FRAME_PROBE_RESP,
bcon->proberesp_ies_len,
bcon->proberesp_ies);
if (rc) {
wil_err(wil, "set_ie(PROBE_RESP) failed\n");
return rc;
}
rc = wmi_set_ie(wil, WMI_FRAME_ASSOC_RESP,
bcon->assocresp_ies_len,
bcon->assocresp_ies);
if (rc) {
wil_err(wil, "set_ie(ASSOC_RESP) failed\n");
return rc;
}
return 0;
}
static int wil_cfg80211_start_ap(struct wiphy *wiphy,
struct net_device *ndev,
struct cfg80211_ap_settings *info)
{
int rc = 0;
struct wil6210_priv *wil = wiphy_to_wil(wiphy);
struct wireless_dev *wdev = ndev->ieee80211_ptr;
struct ieee80211_channel *channel = info->chandef.chan;
struct cfg80211_beacon_data *bcon = &info->beacon;
struct cfg80211_crypto_settings *crypto = &info->crypto;
u8 wmi_nettype = wil_iftype_nl2wmi(wdev->iftype);
wil_dbg_misc(wil, "%s()\n", __func__);
if (!channel) {
wil_err(wil, "AP: No channel???\n");
return -EINVAL;
}
wil_dbg_misc(wil, "AP on Channel %d %d MHz, %s\n", channel->hw_value,
channel->center_freq, info->privacy ? "secure" : "open");
wil_dbg_misc(wil, "Privacy: %d auth_type %d\n",
info->privacy, info->auth_type);
wil_dbg_misc(wil, "BI %d DTIM %d\n", info->beacon_interval,
info->dtim_period);
print_hex_dump_bytes("SSID ", DUMP_PREFIX_OFFSET,
info->ssid, info->ssid_len);
wil_print_bcon_data(bcon);
wil_print_crypto(wil, crypto);
if (wil_fix_bcon(wil, bcon)) {
wil_dbg_misc(wil, "Fixed bcon\n");
wil_print_bcon_data(bcon);
}
mutex_lock(&wil->mutex);
__wil_down(wil);
rc = __wil_up(wil);
if (rc)
goto out;
rc = wmi_set_ssid(wil, info->ssid_len, info->ssid);
if (rc)
goto out;
/* IE's */
/* bcon 'head IE's are not relevant for 60g band */
/*
* FW do not form regular beacon, so bcon IE's are not set
* For the DMG bcon, when it will be supported, bcon IE's will
* be reused; add something like:
* wmi_set_ie(wil, WMI_FRAME_BEACON, bcon->beacon_ies_len,
* bcon->beacon_ies);
*/
wmi_set_ie(wil, WMI_FRAME_PROBE_RESP, bcon->proberesp_ies_len,
bcon->proberesp_ies);
wmi_set_ie(wil, WMI_FRAME_ASSOC_RESP, bcon->assocresp_ies_len,
bcon->assocresp_ies);
wil->secure_pcp = info->privacy;
rc = wmi_pcp_start(wil, info->beacon_interval, wmi_nettype,
channel->hw_value);
if (rc)
goto out;
netif_carrier_on(ndev);
out:
mutex_unlock(&wil->mutex);
return rc;
}
static int wil_cfg80211_stop_ap(struct wiphy *wiphy,
struct net_device *ndev)
{
int rc, rc1;
struct wil6210_priv *wil = wiphy_to_wil(wiphy);
wil_dbg_misc(wil, "%s()\n", __func__);
mutex_lock(&wil->mutex);
rc = wmi_pcp_stop(wil);
__wil_down(wil);
rc1 = __wil_up(wil);
mutex_unlock(&wil->mutex);
return min(rc, rc1);
}
static int wil_cfg80211_del_station(struct wiphy *wiphy,
struct net_device *dev, const u8 *mac)
{
struct wil6210_priv *wil = wiphy_to_wil(wiphy);
mutex_lock(&wil->mutex);
wil6210_disconnect(wil, mac);
mutex_unlock(&wil->mutex);
return 0;
}
static struct cfg80211_ops wil_cfg80211_ops = {
.scan = wil_cfg80211_scan,
.connect = wil_cfg80211_connect,
.disconnect = wil_cfg80211_disconnect,
.change_virtual_intf = wil_cfg80211_change_iface,
.get_station = wil_cfg80211_get_station,
.dump_station = wil_cfg80211_dump_station,
.remain_on_channel = wil_remain_on_channel,
.cancel_remain_on_channel = wil_cancel_remain_on_channel,
.mgmt_tx = wil_cfg80211_mgmt_tx,
.set_monitor_channel = wil_cfg80211_set_channel,
.add_key = wil_cfg80211_add_key,
.del_key = wil_cfg80211_del_key,
.set_default_key = wil_cfg80211_set_default_key,
/* AP mode */
.change_beacon = wil_cfg80211_change_beacon,
.start_ap = wil_cfg80211_start_ap,
.stop_ap = wil_cfg80211_stop_ap,
.del_station = wil_cfg80211_del_station,
};
static void wil_wiphy_init(struct wiphy *wiphy)
{
/* TODO: set real value */
wiphy->max_scan_ssids = 10;
wiphy->max_scan_ie_len = WMI_MAX_IE_LEN;
wiphy->max_num_pmkids = 0 /* TODO: */;
wiphy->interface_modes = BIT(NL80211_IFTYPE_STATION) |
BIT(NL80211_IFTYPE_AP) |
BIT(NL80211_IFTYPE_MONITOR);
/* TODO: enable P2P when integrated with supplicant:
* BIT(NL80211_IFTYPE_P2P_CLIENT) | BIT(NL80211_IFTYPE_P2P_GO)
*/
wiphy->flags |= WIPHY_FLAG_HAVE_AP_SME |
WIPHY_FLAG_AP_PROBE_RESP_OFFLOAD;
dev_dbg(wiphy_dev(wiphy), "%s : flags = 0x%08x\n",
__func__, wiphy->flags);
wiphy->probe_resp_offload =
NL80211_PROBE_RESP_OFFLOAD_SUPPORT_WPS |
NL80211_PROBE_RESP_OFFLOAD_SUPPORT_WPS2 |
NL80211_PROBE_RESP_OFFLOAD_SUPPORT_P2P;
wiphy->bands[IEEE80211_BAND_60GHZ] = &wil_band_60ghz;
/* TODO: figure this out */
wiphy->signal_type = CFG80211_SIGNAL_TYPE_UNSPEC;
wiphy->cipher_suites = wil_cipher_suites;
wiphy->n_cipher_suites = ARRAY_SIZE(wil_cipher_suites);
wiphy->mgmt_stypes = wil_mgmt_stypes;
}
struct wireless_dev *wil_cfg80211_init(struct device *dev)
{
int rc = 0;
struct wireless_dev *wdev;
dev_dbg(dev, "%s()\n", __func__);
wdev = kzalloc(sizeof(*wdev), GFP_KERNEL);
if (!wdev)
return ERR_PTR(-ENOMEM);
wdev->wiphy = wiphy_new(&wil_cfg80211_ops,
sizeof(struct wil6210_priv));
if (!wdev->wiphy) {
rc = -ENOMEM;
goto out;
}
set_wiphy_dev(wdev->wiphy, dev);
wil_wiphy_init(wdev->wiphy);
rc = wiphy_register(wdev->wiphy);
if (rc < 0)
goto out_failed_reg;
return wdev;
out_failed_reg:
wiphy_free(wdev->wiphy);
out:
kfree(wdev);
return ERR_PTR(rc);
}
void wil_wdev_free(struct wil6210_priv *wil)
{
struct wireless_dev *wdev = wil_to_wdev(wil);
dev_dbg(wil_to_dev(wil), "%s()\n", __func__);
if (!wdev)
return;
wiphy_unregister(wdev->wiphy);
wiphy_free(wdev->wiphy);
kfree(wdev);
}