mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-28 11:18:45 +07:00
962d8cdc31
is actually "active high". Thanks for Troy Kisky for pointing that out. Since the patch is in linux-next, this patch is incremental and doesn't replace the original patch. Signed-off-by: Bernhard Walle <bernhard@bwalle.de> Acked-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
66 lines
2.3 KiB
Plaintext
66 lines
2.3 KiB
Plaintext
* Freescale Fast Ethernet Controller (FEC)
|
|
|
|
Required properties:
|
|
- compatible : Should be "fsl,<soc>-fec"
|
|
- reg : Address and length of the register set for the device
|
|
- interrupts : Should contain fec interrupt
|
|
- phy-mode : See ethernet.txt file in the same directory
|
|
|
|
Optional properties:
|
|
- phy-reset-gpios : Should specify the gpio for phy reset
|
|
- phy-reset-duration : Reset duration in milliseconds. Should present
|
|
only if property "phy-reset-gpios" is available. Missing the property
|
|
will have the duration be 1 millisecond. Numbers greater than 1000 are
|
|
invalid and 1 millisecond will be used instead.
|
|
- phy-reset-active-high : If present then the reset sequence using the GPIO
|
|
specified in the "phy-reset-gpios" property is reversed (H=reset state,
|
|
L=operation state).
|
|
- phy-supply : regulator that powers the Ethernet PHY.
|
|
- phy-handle : phandle to the PHY device connected to this device.
|
|
- fixed-link : Assume a fixed link. See fixed-link.txt in the same directory.
|
|
Use instead of phy-handle.
|
|
- fsl,num-tx-queues : The property is valid for enet-avb IP, which supports
|
|
hw multi queues. Should specify the tx queue number, otherwise set tx queue
|
|
number to 1.
|
|
- fsl,num-rx-queues : The property is valid for enet-avb IP, which supports
|
|
hw multi queues. Should specify the rx queue number, otherwise set rx queue
|
|
number to 1.
|
|
- fsl,magic-packet : If present, indicates that the hardware supports waking
|
|
up via magic packet.
|
|
|
|
Optional subnodes:
|
|
- mdio : specifies the mdio bus in the FEC, used as a container for phy nodes
|
|
according to phy.txt in the same directory
|
|
|
|
Example:
|
|
|
|
ethernet@83fec000 {
|
|
compatible = "fsl,imx51-fec", "fsl,imx27-fec";
|
|
reg = <0x83fec000 0x4000>;
|
|
interrupts = <87>;
|
|
phy-mode = "mii";
|
|
phy-reset-gpios = <&gpio2 14 0>; /* GPIO2_14 */
|
|
local-mac-address = [00 04 9F 01 1B B9];
|
|
phy-supply = <®_fec_supply>;
|
|
};
|
|
|
|
Example with phy specified:
|
|
|
|
ethernet@83fec000 {
|
|
compatible = "fsl,imx51-fec", "fsl,imx27-fec";
|
|
reg = <0x83fec000 0x4000>;
|
|
interrupts = <87>;
|
|
phy-mode = "mii";
|
|
phy-reset-gpios = <&gpio2 14 0>; /* GPIO2_14 */
|
|
local-mac-address = [00 04 9F 01 1B B9];
|
|
phy-supply = <®_fec_supply>;
|
|
phy-handle = <ðphy>;
|
|
mdio {
|
|
ethphy: ethernet-phy@6 {
|
|
compatible = "ethernet-phy-ieee802.3-c22";
|
|
reg = <6>;
|
|
max-speed = <100>;
|
|
};
|
|
};
|
|
};
|